F A L C O N T S E R I E S F E A T U R E S

F A L C O N T S E R I E S Simply put, the Falcon T-Series lock is the most versatile lockset in the industry. This extra heavy duty lock can accept any manufacturer s cylinder, and the cylinder can easily be removed for quick, easy re-keying. Redesigned with a compression spring behind the cylinder, the T-Series is now stronger than ever and lever sag has been virtually eliminated. This adaptable lock is well suited to either new construction or retrofit use in buildings as varied as multi-family, retail, institutional and government/military. F E A T U R E S Brass or cold-formed steel construction, zinc plated and dichromated for rust resistance Proven compression spring design supports levers, eliminating lever sag and provides years of reliable service Heavy wrought brass or bronze roses over steel through-bolted rose inserts PressureRelease outside lever disengages when locked to protect internal mechanisms 3

T S E R I E S L E V E R D E S I G N S Levers Levers are solid pressure cast zinc, finished to match mating parts. Roses are wrought brass or bronze installed over steel through-bolted rose inserts. Pressure Release levers are standard. Levers are secured by a spring-loaded retainer. Retainer cannot be depressed when locks have been locked. 5 3-1/2 A Avalon 3-1/4 5 3-1/2 3-1/4 D Dane 5 3-1/2 Q Quantum 3-1/4 Abrasive Coated Levers All levers are available with abrasive coating along the length of the lever to identify entrances to hazardous areas to the handicapped. To order add: with abrasive coated outer lever in detail section of order. 4

T S E R I E S LO C K F E AT U R E S A N D S P E C I F I C AT I O N S Lock Features Door Thickness: 1-3/4 to 2-1/8 standard. Thin door adapter kit (A30775-000-00) available for doors thinner than 1-3/4, please specify door thickness. Backset: 2-3/4 standard. 2-3/8 also available. Link (A22161-005-10) available for 5 backset. Mechanism: Parts constructed of brass or cold formed steel, zinc plated and dichromated for rust resistance. Springs are stainless steel. Attachment: Lock chassis secured to door by threaded mounting nuts. Completely preassembled outer trim and inner spindle assembly are through-bolted over chassis using (2) 10-32 screws. Adding rose and lever to inner spindle assembly completes installation. Handing: Locks are non-handed. Cylinders: Drilled with 6-pin chambers, pinned in 5. Pinning in 6 chambers available when specified, at no cost. 7-pin cylinders also available. Cylinder assemblies removable to rekey. Also available with 6 or 7-pin interchangeable core cylinders. Cylinder housings and plugs machined from solid brass. Springs are phosphor bronze. Two nickel silver keys furnished standard. Interchangeable core design is available for small format (SFIC) and large format for most manufacturers, see page 8. Falcon Lock T Series Specifications Key-in-lever cylindrical locksets shall be Falcon Lock T Series or equal and meet the following requirements: All locks shall meet the new ANSI/BHMA A156.2, Series 4000, Grade 1 for key-in-lever locksets. Locksets shall be UL Listed (3 hour A Label). Locksets shall be provided standard with Pressure Release feature. When outside lever is locked, it is not rigid but will move freely without operating the latch bolt. Lever trim shall have individual heavy-duty compression springs behind rose for lever return and to prevent lever sag. Trim shall be through-bolted with two (2) 10-32 screws coated with thread sealant to provide strength and resistance to loosening. Inner Keyways: G keyway standard on conventional cylinders. A keyway standard on I/C core cylinders. Also available with some optional keyways. Trim: Roses are heavy wrought brass or bronze, installed over pressure cast rose inserts which are through-bolted through door. Levers are pressure cast (solid levers no inserts) material finished to match mating parts. Latches: 9/16 bolt projection, UL listed with latch faceplates 2-1/4 x 1-1/8 with square corners standard. 3/4 projection, UL listed latch with 2-3/4 backset also available. Adjustable front standard. See page 10 for optional latches. Strikes: 4-7/8 x 1-1/4 ANSI strike with curved lip to meet ANSI A115.2 door frame preparation standard. Consult page 11 for other available strike sizes and configurations. Screws: Furnished with combination screws for use in wood or metal doors and frames. Electrified Functions: Available in 24 VDC.185 AMP. ANSI/BHMA: Meets ANSI/BHMA A156.2, Series 4000, Grade 1. UL: 3 hour A label. and outer trim shall bottom out to prevent door collapse. Roses shall be minimum of 3-1/2 diameter. All lever designs shall be solid and meet the federal ADA and state disability requirements. Inside levers shall be attached by Allen-head set screw to prevent tampering or vandalism. Locksets shall adjust to fit door thickness from 1-3/4 to 2-1/8. All locksets shall be non-handed and not require field disassembly for re-handing. Preparation for door must be non-handed. Acceptable manufacturer: FALCON LOCK 5/16 Dia. thru hole 2-3/8, 2-3/4 Backset (from center of door for beveled stile) C L door, lock & strike are common 5/32 1-1/4 5/16 1 Dia. 3/4 2-3/4 5/32 x 1/8 Deep 2-1/4 1-1/8 4-7/8 3-3/8 3-1/2 4-1/8 14 2-25/32 Elevation 2-1/8 Dia. Door Edge 1-1/8 1-1/16 Standard Strike 3/8 9/16

Machined steel lever spindle carries high levels of torque and shear. This spindle is re-used when upgrading existing locks to the new design. Heavy-duty case zinc rose insert accommodates the new style spring. This insert is replaced when upgrading to the new design. New stamped steel torque plates hold the springs in place and transfer the spring energy to the spindle and lever assembly. Stainless steel compression springs replace steel torsion springs, providing the most reliable and robust method of supporting levers. New retaining ring holds the assembly together. Falcon T-series locks feature our high performance compression springs. This newly designed spring far exceeds ANSI/BHMA requirements for cycle tests, and ensures the most robust support for levers. Unlike typical torsion springs that can break at the bend points, this new design will provide years of reliable service even in high-use applications. A retrofit kit is available to outfit your existing T-series locks with this new, more robust spring design. 5

To order Falcon T Series locksets, please consult page 15 for ordering information and assistance. Indicates interchangeable core available. Catalog Number Function Description ANSI No. & Grade T571 Dormitory Lock Deadlocking latch bolt by levers except when locked by push button in inside lever. Key in outside lever locks or unlocks outside lever and releases button. Closing door releases push button. Inside lever always free. F90-1 T581 Storeroom Lock Deadlocking latch bolt by lever inside or key outside. Outside lever is inoperable. Inside lever always free. F86-1 T851 Storeroom (Electrified Fail Safe) Inside Lever Always Free. Latch bolt operated by lever from either side except when outer lever is electrically locked. When outer lever is locked (inoperable), latch bolt retracted by key in cylinder outside. 24 volt DC.185 Amps, continuous duty. T881 Storeroom (Electrified Fail Secure) Inside Lever Always Free. Deadlocking latch bolt operated by lever inside at all times. Outside lever inoperable until electrically unlocked, then latch bolt from either side. When outside lever is inoperable latch bolt retracted by key in cylinder outside. 24 volt DC.185 Amps, continuous duty.. T12 Dummy Trim Single Trim-surface mounted rigid lever. 7

W Series Medium Duty, Grade 2 Cylindrical Lever and Knob Locks

FALCON W SERIES Whether your application is government/military, retail, industrial or multi-family, there s a W Series lock that fits perfectly. In two popular lever and two popular knob styles Falcon can match most commercial door trim. The Falcon W Series locks feature conventional cylinders and small format interchangeable cores that are compatible with SFIC products from other manufacturers. Our conventional cylinders are available in all Falcon conventional key sections as well as Schlage C Keyway, which we now masterkey across the complete Falcon product line. If quality product at a value price is what you are looking for, the Falcon W Series is the lock for you. And they re backed by one of the best names in the business, Ingersoll Rand. FEATURES Stainless steel latch bolt UL listed latch standard Solid, pressure-cast zinc levers Wrought brass or bronze roses over steel through-bolted rose inserts Conventional cylinders or interchangeable core keying compatible with SFIC products from Falcon or other manufacturers Non-handed levers for easy Þeld installation 3

LEVERS Levers are solid pressure-cast zinc, fi nished to match mating parts. Roses are wrought brass or bronze installed over steel through-bolted rose inserts. A spring-loaded retainer secures levers. Secure side retainer cannot be depressed without a key that operates the lock. Small Format Interchangeable Core (SFIC) Dane shown Thumbturn (interior) Quantum shown Plain Dane shown Conventional Cylinder Quantum shown Dane Quantum 2-11/32 2-19/32 ~ 2-11/32 2-19/32 ~ 4-5/8 4-5/8 ø3-3/8 ø3-3/8 Abrasive Lever Options All levers are available with an abrasive strip along the length of the lever to identify entrances to areas hazardous to the disabled. To order add 6 (for example, 6DA for Dane lever or 6QU for Quantum lever) to the order number. 4

Catalog Number W101 Description Passage Latchset Latch bolt by levers at all times. ANSI Number and Grade F75 W161 Communicating/Exit Latch Deadlocking latch bolt by inside lever. Non-removable blank plate outside. Inside lever is always free. W201 W301 W501 W511 W561 Patio Lock Deadlocking latch bolt by levers. Outside lever is locked by push button from inside. Rotating inside lever or closing door releases button and unlocks outside lever. Privacy Lock Latch bolt by levers. Outside lever is locked by push button on inside lever. Rotating inside lever or closing door releases push button and frees outside lever. Inside lever is always free. Emergency release in outside lever unlocks door. Entry Lock Push button locking. Button on inside locks outside lever until unlocked by key or by rotating inside lever. Closing door release push button and unlocks door. Inside lever always free. Deadlock latchbolt. Entry/OfÞce Lock Deadlocking latch bolt by levers. Turn/push button locking. Pushing and turning button locks outside lever, requiring use of a key for unlocking the door until button is manually unlocked. Pushing button locks outside lever until unlocked by key or by rotating inside lever. Inside lever is always free. Classroom Lock Deadlocking latch bolt by levers. Outside lever is locked by key in outside lever. Inside lever is always free. F77 F76 F82 F109 F84 W581 W711 W12 Storeroom Lock Deadlocking latch bolt by lever inside or key outside. Outside lever is always locked. Inside lever is always free. Apartment Entrance Lock Deadlocking latch bolt by levers. Turn/push button locking. Pushing and turning button locks outside lever, requiring use of a key for unlocking the door until button is manually unlocked. Pushing button locks outside lever until unlocked by key, by rotating inside lever, or by closing the door. Inside lever is always free. Single Dummy Trim Single trim, surface-mounted rigid lever. F86 5

24-R Series Rim Device Non-Handed Rim Device 17-R Series Panic Exit Hardware The Falcon 24-R Series narrow stile rim device allows for application versatility in high-traffic installations. Standard features include a single-point, rim type latch and a streamlined touch bar design. This device can also be electrified for maximum ease of use and accessibility. 299 Strike 2789 Dogging Key Cylinder Dogging Single Door Application Door Door Min Min Door Device Size Strike Stile (in) Opening Width 24-R 3 299 3 1 2 2 7 3 8 264 3 3 8 2 7 1 4 1439 2 1 4 2 6 1 2 1606 2 3 4 2 7 1 8 24-R 4 299 3 1 2 3 1 3 8 264 3 3 8 2 7 1 4 1439 2 1 4 3 1 2 1606 2 3 4 3 1 1 8 Double Door Application Door Strike x Min Min Door Device Size Mullion Stile (in) Opening Width 24-R 3 299 x 2923 3 1 2 2 7 1 2 299 x 4023 4 2 7 3 4 264 x 2923 3 3 8 2 7 3 8 264 x 4023 3 5 8 2 7 3 4 1439 x 2923 3 1 2 2 7 1 8 1439 x 4023 3 3 4 2 7 3 8 1606 x 2923 3 1 2 2 7 1 4 1606 x 4023 3 3 4 2 7 1 2 4396 x 4423 2 1 8 2 6 1 2 24-R 4 299 x 2923 3 1 2 3 1 1 2 299 x 4023 4 3 1 3 4 264 x 2923 3 3 8 3 1 3 8 264 x 4023 3 5 8 3 1 3 4 1439 x 2923 3 1 2 3 1 1 8 1439 x 4023 3 3 4 3 1 3 8 1606 x 2923 3 1 2 3 1 1 4 1606 x 4023 3 3 4 3 1 1 2 4396 x 4423 2 1 8 3 1 2 Specifications Hand: Non-handed. Functions: 24-EO (Exit Only) has all functions built in. Order trim with the device, or add it later. See Trim Selection Chart on page 29. Finishes: US3 (605); US4 (606); US10 (612); US26 (625); US26D (626); US32 (629); US32D (630); US28 (628), 313AN. (See page 29 for finishes.) strikes: 299 strike standard. See page 27 for optional strikes. Latchbolt: Stainless steel, 3 4 throw. Deadlocking Latchbolt: Optional. Specify DL prefix. Dogging Feature: 1 2 turn hex dogging standard. No threaded parts to wear out. Cylinder Dogging: Specify CD prefix. Uses 1 1 8 long mortise cylinder with standard cam. Stock Sizes: See chart to left. Doors: 1 3 4 thick, wood or metal. Specify thickness if other than 1 3 4. Projection: 2 3 4 maximum, 2 dogged. Mounting Height: 40 from CL to finished floor. Electric Function: Can be interfaced with building security systems. Latch retraction, security monitoring, electric dogging, delayed egress and exit alarm available (EL and ED fail- secure only). Subject to code requirements, state and local. (See pages 33-41 for details.) Fasteners: All mounting screws are concealed. Sex Bolts: Recommended when device is used with hollow core wood, composite or light gauge hollow metal doors. For EO device, specify 4-425 (#I0-24) SNB and 2-325 ( 1 4-20) SNB. For devices with trim, specify 4-425 (#I0-24) SNB. ANSI: Certified ANSI A156.3-2001 Grade 1 standards. Center Case & Working Parts: Wrought steel with heavy wrought and sintered metal parts. Shim Kit: For glass lite applications; 1 4 thick, specify SK24-R. 20

24 series Trim Designs Trim Designs Lever Trims (712L) Lever Designs Dane Projection: 2 1 4 Quantum Projection: 3 1 8 Sutro Projection: 2 13 16 712L 712L/NL 712L/DT 712L/BE Projection: 2 1 4, Dane 2 13 16, Sutro 3 1 8, Quantum Dane, Quantum and Sutro levers return to within 1 2 of door. Pull Trims (710) Knob Trim (711K) Athena (715) 710TP 710DT 710NL 711K 711-NL 711K-DT K-BE 715DT Grip overall: 9 Width: 1 5 8 Pull: 6 1 4 C x C Projection: 2 1 4 Delta Trims 1 1 8 mortise cylinder 1 cylinder 28 719TL 719TLP 718TP 718DT 718C 718NL 717DT Specify Handing All Delta pulls: 6 1 4 C x C All Delta pulls: 2 projection TLP, NL, TP & DT: 13 overall length TL: 7 1 4 L x 1 3 4 W x 1 3 4 projection Brass, Stainless and/or Plated finishes. For cylinder information see page 14. When locking function is not required, specify trim by (BE) blank escutcheon.

25-R Series Rim Device Panic Exit Hardware The Falcon 25-R Series rim device meets the demanding requirements of high traffic installations with a single-point, rim type latch and a streamlined touch bar design. This device can also be electrified for maximum ease of use and accessibility. 299 Strike 2789 Dogging Key Cylinder Dogging Single Door Application Door Door Min Min Door Device Size Strike Stile (in) Opening Width 25-R 3 299 4 2 7 1 2 264 3 7 8 2 7 3 8 1439 3 1 4 2 6 1 2 1606 3 5 8 2 7 25-R 4 299 4 3 1 1 2 264 3 7 8 3 1 3 8 1439 3 1 4 3 1 2 1606 3 5 8 3 1 Double Door Application Door Strike x Min Min Door Device Size Mullion Stile (in) Opening Width 25-R 3 299 x 2923 4 1 8 2 7 5 8 299 x 4023 4 3 8 2 7 7 8 264 x 2923 4 2 7 1 2 264 x 4023 4 1 4 2 7 3 4 1439 x 2923 3 7 8 2 7 3 8 1439 x 4023 4 1 8 2 7 5 8 1606 x 2923 4 1 4 2 7 1 4 1606 x 4023 4 1 2 2 7 1 2 25-R 4 299 x 2923 4 1 8 3 1 5 8 299 x 4023 4 3 8 3 1 7 8 264 x 2923 4 3 1 1 2 264 x 4023 4 1 4 3 1 3 4 1439 x 2923 3 7 8 3 1 3 8 1439 x 4023 4 1 8 3 1 5 8 1606 x 2923 4 1 4 3 1 1 4 1606 x 4023 4 1 2 3 1 1 2 25-V x 25-R 3 1609 2 3 8 2 7 3 4 25-V x 25-R 4 1609 2 3 8 3 1 3 4 Specifications Hand: Non-handed. Finishes: US3 (605); US4 (606); US10 (612); US26 (625); US26D (626); US32 (629); US32D (630); US28 (628), 313AN. (See page 17 for finishes.) Strikes: Latchbolt: Deadlocking Latchbolt: Dogging Feature: Cylinder Dogging: Stock Sizes: Doors: Projection: Mounting Height: 299 strike standard. See page 15 for additional info. Stainless steel, 3 4 throw. Standard. 1 2 turn hex dogging standard. No threaded parts to wear out. Specify CD prefix. Uses 1-1 8 long mortise cylinder with standard cam. See chart to left. Cut to size in the field. 1-3 4 thick, wood or metal. Specify thickness if other than 1-3 4. 2 3 4 maximum, 2 dogged. 40 1 4 from CL to finished floor. Electric Function: Can be interfaced with building security systems. Latch retraction, FSA/FSE trim, security monitoring, electric dogging, delayed egress and exit alarm available (EL and ED fail-secure only). Subject to code requirements, state and local. (See pages 33-41 for details). Fasteners: All mounting screws are concealed, sheet metal screws and machine screws standard. Sex Bolts: Recommended when device is used with hollow core wood, composite or light gauge hollow metal doors. For EO device, specify 8-425 (#I0-24) SNB. For devices with trim, specify 2-425 (#IO-24) SNB. ANSI: Certified ANSI A156.3-2001 Grade 1 standards. Center Case & Working Parts: Center case is heavy wrought and sintered metal parts. Shim Kit: For glass lite applications; 1 4 thick, specify SK25-RM. 579 Strike Retrofit Kit: Consult factory. 6

25 series Trim Designs Functionality built into the trim, facilitating easy door preps, easy field retrofit and easy ordering. Lever Trims (510L) Lever Designs 510L 510L-NL 510L-DT 510L-BE Projection: 2 1 4, Dane 2 13 16, Sutro 3 1 8, Quantum Vandal-Resistant Lever Trims (511L) Dane Projection: 2 13 16 Quantum Projection: 3 1 2 Sutro Projection: 3 13 16 Lever: 4 5 8 escutcheon: 2 3 4 x 9 3 4 (specify handing) brass and stainless finishes. Protected by easily replaceable shear pin. Lever is reversible, supplied RHR if not specified. For keyed functions, see page 14 for cylinder requirements. Provides resistance to rotation, making damage of trim due to attack from the outside less likely. Designed to operate normally after vandalism attempts without the need for maintenance personnel intervention. Pull Trims (512TP) Heavy duty, vandal-resistant, ANSI AI56.3 Grade 1 security trim Lever deflects up to 22 ft-lb for a minimum of 10,000 vandal-resistant cycles Vandal resistance is present in both lever rotation directions After lever is fully deflected, lever stops rotating and a shear pin breaks at 70 ft-lb to prevent damage to unit Available on 25 rim, vertical, mortise, and concealed devices Retrofits all existing 25 trim without additional door prep LK monitor switch is available Works with all electric lock and unlock functions Available in all finishes and designs including Dane, Quantum and Sutro Knob Trims (513K) Cylinder Only (NL-OP) Delta (717) 512TP 512NL 512DT 512TP-BE Escutcheon: 2 3 4 x 16 Grip: 6 1 4 C C Projection: 2 11 16 Brass and Stainless Steel For keyed functions, see page 14 for cylinder requirements. 717DT 513K-DT 513K-BE 513K 513K-NL Round Ball Knob Escutcheon: 2 3 4 x 9 3 4 Projection: 3 3 8 Brass and Stainless Steel For keyed functions, see page 14 for cylinder requirements. Key retracts latch bolt. Cylinder sold separately (see page 14). 16

F-25-R Series Rim Device ZFire Exit Hardware The Falcon F-25-R Series rim device combines sleek styling and durability with the protection of a fire-rated device. The F-25-R also features a single-point, rim type latch and can be electrified. 299F Strike Single Door Application Door Door Min Min Door Device Size Strike Stile (in) Opening Width F-25-R 3 299-F 4 2 7 1 2 F-25-R 4 299-F 4 3 1 1 2 Double Door Application Door Strike x Min Min Door Device Size Mullion Stile (in) Opening Width F-25-R 3 299-F x F-4023 4 3 8 2 7 7 8 499-F x F-4023 4 1 2 2 7 7 8 F-25-R 4 299-F x F-4023 4 3 8 3 1 7 8 499-F x F-4023 4 1 2 3 1 7 8 specifications Hand: Non-handed. UL: A label (3 hr.); 4 0 x 8 0 ; 8 0 x 8 0 with F-4023 mullion. B label (1 1 2 hr.); 8 0 x 8 0 ; with KRF4023. Finishes: US3 (605); US4 (606); US10 (612); US26 (625); US26D (626); US32 (629); US32D (630); US28 (628), 313AN. (See page 17 for finishes.) strikes: 299F strike standard 499F with mullion optional Latchbolt: Stainless steel, 3 4 throw. Deadlocking Latchbolt: Standard. Stock Sizes: See chart to left. Cut to size in the field. Doors: 1 3 4 thick, wood or metal. Specify thickness if other than 1 3 4. Projection: 2 3 4 maximum. Mounting Height: 40 1 4 from CL to finished floor. Electric Function: Can be interfaced with building security systems. Latch retraction, FSA/FSE trim, security monitoring, electric dogging, delayed egress and exit alarm available (EL and ED fail- secure only). Subject to code requirements, state and local. (See pages 33-41 for details). Fasteners: All mounting screws are concealed, sheet metal screws and machine screws standard. Sex Bolts: Required for use in EO applications when used with wood, composite or non-reinforced hollow metal doors. For EO device, specify 8-425 (#10-24) SNB. For devices with trim, specify 2-425 (#10-24) SNB. ANSI: Certified ANSI A156.3-2001 Grade 1 standards. Center Case & Working Parts: Center case is heavy wrought and sintered metal parts. Shim Kit: For glass lite applications; 1 4 thick, specify SK25-RM. 7

100 Series Concealed Overhead Door Holders/Stops Materials and Finishes: In Heavy Gauge Brass or 300 Series Stainless Steel, these models offer the broadest range of finishes in the industry, complementing any design and offering the highest resistance to corrosion. Available in the following finishes: 100 Series Heavy-Duty Glynn-Johnson offers a complete line of overhead door holders and stops, accommodating virtually all openings with solutions for even the most complex door control problems. These concealed holders and stops provide the most attractive and reliable heavy-duty door control available. Glynn-Johnson 100 series holders and stops provide the most reliable and versatile concealed overhead door control. They are designed for installation on virtually all types of doors mounted on conventional type butt hinges, pivots, continuous hinges, swing clear hinges and numerous other specialty hinges. When used in conjunction with many surface-applied door closers, 100 series holders and stops provide the most effective control for entrance doors and vestibule doors of all types, as well as heavy or often used interior doors. Templates provided allow for variable mounting positions, ranging from 85-110 of opening. Five Models: 100H Series Hold-Open Model 100HP Series Internal Hold-Open Model 100F Series Friction Hold-Open Model 100S Series Stop-Only Model 100SE Series Special Stop-Only Model Six Sizes: Each model comes in six sizes. Simple Standardized Three Options: ADJ Adjustable Jamb Bracket CJ Jamb Bracket for use with LCN5030 Closer SOC Pin-in-Socket Security Screw Package Unmatched Convenience: Non-handed Improved Compatibility with Door Closers Single/Double-Acting Doors Interior/Exterior Applications Reduced Door Prep Durable Improved Corrosion Resistance Function Conversion Kits are Available. Finishes US3 US4 US10 US10B US32 US32D SP4 SP10 SP28 SP313 SPBLK Models Description Polished Brass Satin Brass Satin Bronze Oil Rubbed Bronze Polished Stainless Steel Satin Stainless Steel Powder Coat Brass Powder Coat Bronze Powder Coat Aluminum Powder Coat Dark Bronze Powder Coat Black These models provide a wide range of optional features, and are ideal for use on entrance and vestibule doors, large doors, doors opened frequently, or doors subject to abuse. These models are also furnished with an offset-style jamb bracket. Designed for heavy-duty applications, 100 series models will provide long-lasting protection to doors, frames, hinges, related hardware and surrounding walls or obstructions. 100H Series Hold-Open (Suffix H) The Hold-Open function should be used where it is desired to hold a door open at a predetermined position for short or long periods of time, permitting an unobstructed traffic flow through the opening. These models are both selective and adjustable, featuring the most reliable Hold-Open mechanism available. They feature a control knob which protrudes from the face of the door and turns the Hold-Open function on or off. Set in the inactive position, the unit acts as a stop and shock absorber. The tension on the Hold-Open mechanism can be adjusted using an allen wrench to offset air currents or other exterior conditions. The Hold-Open tension adjustment is located in the bottom of the track in the top of the door. 100HP Series Internal Hold-Open These models provide a Hold-Open unit with the Hold-Open mechanism built into the channel, thus reducing the door prep. The 100HP have a preset Hold-Open force that is not adjustable. The Hold-Open feature is not selectable in these units, so the doors are always held open. 18

100F Series Friction Hold-Open (Suffix F) Friction Hold-Open models provide an alternative holding method, ideal for heavy patient room doors, closet doors or similar applications where multiple Hold-Open positions are desired. The friction tension is adjusted using an allen wrench and an open end wrench. The friction tension adjustment is located on the top of the slider in the channel. 100S Series Stop-Only (Suffix S) When the Hold-Open function is not required, the Stop-Only function provides the same effective door control minus the Hold-Open feature. The Stop-Only model may be used on fire doors. 100SE Series Special Stop-Only (Suffix SE) When Stop-Only models are used in conjunction with single point Hold-Open electronic door closers, they may be ordered without the shock-absorbing mechanism. Used as an auxiliary stop with these closers, they will prolong the life of the closer. The stop location is adjusted using an allen wrench on the stop block located in the channel. Note: Caution should be used when using this option in other applications, as the elimination of the shock-absorbing spring can put added stress on door and frame if used improperly. Application Information UL Classification The 100 series Stop-Only models are classified by Underwriters Laboratories (UL) as Miscellaneous Fire Door Accessories. This classification applies to use on either Hollow Metal Fire Doors or Wood Fire Doors. Where Wood Door manufacturer s listing allows for the cutout required for installation, concealed overhead stops may be used on those wood fire doors. These units may be used on doors of any rating. As a reminder, the Miscellaneous Fire Door Accessories (GVUX) section is defined by UL as: Miscellaneous fire door accessories are intended in the individual Listings. The accessories have been investigated to determine that when installed in accordance with the manufacturer s instructions, the accessories do not adversely affect the fire rating of the fire door and/or fire door frames. Dead Stop Templating: If a wall or similar obstruction is in place at 110 or less opening angle (i.e. doors that open back-to-back), Dead Stop Templating should be used. This includes all Hold-Open, Friction and Stop-Only models, except when the SE Option is used. The Dead Stop position is reached when the shock-absorbing spring is fully compressed, the initial degree of opening will be 5 to 7 less than the Dead Stop opening. Example: If the holder is templated to 100 Dead Stop, the door will hold open somewhere between 93 and 95, but no further than 100. Note: Do not use dead-stop templating on the 100SE Series since there is no shock-absorbing spring. Environmental Considerations: Environmental factors should always be considered when specifying overhead holders and stops. Doors that are positioned on a building s exterior or subject to corrosive conditions should be equipped with a holder constructed primarily of stainless steel or brass materials. For interior applications, steel is acceptable, though brass substrates generally provide a more attractive architectural-grade finish. Function Conversion Kits FK100F Converts a 100H or 100S unit into a 100F unit. To order specify FK100F. FK100H Converts a 100F or 100S unit into a 100H unit. To order specify FK100H. No kit is needed to convert a 100H or 100F unit into a 100S unit. Options Suffix ADJ (Adjustable Jamb Bracket): An additional option on the 100 series is the adjustable jamb bracket, which allows the degree of Hold-Open or Stop angle to be adjusted after installation. Suffix ADJ is available in all functions, but only in sizes 3, 4, 5 & 6. ADJ jamb bracket requires additional frame prep. The ADJ option cannot be added to an existing unit, it must be factory ordered. Suffix CJ (Closer Jamb Bracket): Provides a special jamb bracket needed for 100 series units used with LCN5030 closers. These special jamb brackets are handed, so handing will need to be specified when ordering the CJ option, CJLH for a left hand door and CJRH for a right hand door. The CJ option cannot be added to an existing unit, it must be factory ordered. Suffix SOC (Pin-in-Socket Security Screw Package): A screw package with pin-in-socket screws for mounting the jamb bracket to the frame is provided instead of the standard screw package. 19

100 Series Concealed Overhead Door Holders/Stops 3/4" 1/4" 2" 1" 1-1/4" 1" 1-1/4" 4-1/4" 1" 1/4" 1-1/4" 3/8" 1/4" 3/4" 2-3/8" 5-1/2" 3-1/2" 1/2" 12" 1-1/4" 3/8" 100 Series Sizing Chart BUTTS/OFFSET PIVOTS CENTER HUNG DOOR STOP HOLD DOOR STOP HOLD SIZE OPENING ONLY OPEN FRICTION OPENING ONLY OPEN FRICTION 1 18" 23" 101S* 101H* 101F* ----- ---- ---- ---- 2 23-1/16" 27" 102S* 102H* 102F* ----- ----- ----- ----- 3 27-1/16" 33" 103S 103H 103F 33-1/16" 39" 103S 103H 103F 4 33-1/16" 39" 104S 104H 104F 39-1/16" 45" 104S 104H 104F 5 39-1/16" 45" 105S 105H 105F 45-1/16" 51" 105S 105H 105F 6 45-1/16" 54" 106S 106H 106F 51-1/16" 59" 106S 106H 106F Note: This chart illustrates the most common types of hinging and door opening sizes. For unusual door details, contact Glynn-Johnson for availability. *These sizes are not available for use with offset pivots. Also not available with the ADJ option. BHMA/ANSI, A156.8 & FED. Spec. Cross Reference G-J Model BHMA* FED. Spec. 101-106 H C01511 1160 101-106 S C01541 ---- 101-106 F C01531 ---- * First numeral (0) designates optional material. To specify: Brass material, change 0 to 1 (i.e. C11511) Stainless Steel material, change 0 to 5 (i.e. C51511) BHMA All 100 series models are designed for heavy-duty applications and far exceed BHMA cycle test and force test requirements for Grade 1 holders and stops. The template information on this page is for reference only and is not intended to serve as an installation template. For complete dimensional information, refer to Glynn-Johnson template book. 20

7226 & 7226F 3/4" Offset 7226 or 7226F Pivot Sets 7226 Pivot Set Non-handed 3/4" offset pivot set consisting of a base plate7226f Pivot Set mounted 7226 or 7226F Bottom Pivot, and a head frame mounted 7226 or 7226F Top Pivot. Door Thickness minimum 1-3/4" (44mm), bevel 1/8" (3mm) in 2" (51mm). Center Line Offset 3/4" (19mm) from face of door and 3/4" from edge of door. Maximum Load 600 pounds (272 kg). UL Listed 7226 for 20 minute rated door. 7226F for 3 hour rated door. 7226F meets ANSI/BHMA Grade 1. Vertical Adjustment Range of 3/16" (5mm), which includes a positive locking feature. Optional Intermediate Pivot For 7226 set, use 7226 Intermediate Pivot (handed). For 7226F set, use 7226F Intermediate Pivot (handed). Each Intermediate Pivot carries up to an additional 100 pounds (45.5 kg) load or needed for doors over 7'. See page 42. Optional 7226 PT Power Transfer Intermediate Pivot (handed). Provides 4 wire transfer with no weight bearing capabilities. See page 48. How to Order: 7226 - - - Rating: Blank F Non-fire-rated Fire-rated Pivot Style: Blank Top and bottom set TOP Top pivot only BTM Bottom pivot only INT Intermediate pivot only PT INT Power transfer intermediate pivot only Handing: LH Left-hand door RH Right-hand door Finishes: Non-Fire-Rated US3, US4, US10, US10B, US26, US26D, SP4, SP10, SP28, SP313, SPBLK Fire-Rated US3, US10, US32, US32D, SP4, SP10, SP28, SP313, SPBLK P I V O T S 36

7200 Series Pivots - Overview 3/4" Offset Pivots - 200 Lb. Doors 7212-7215-7222-7226-7227 Top Pivot 7212V Top Pivot Optional 7212 PIVOT SET 7222 PIVOT SET 7212V PIVOT SET 7212-7212V-7222 Intermediate Pivot 7212 Bottom Pivot 7222 Bottom Pivot 7212 Bottom Pivot 3/4" Offset Pivots - Standard and Fire-Rated - 500 to 700 Lb. Doors 7212-7215-7222-7226-7227 Top Pivot 7215F-7226F-7227F Top Pivot Optional 7215 OR 7215F PIVOT SET 7226 OR 7226F PIVOT SET 7227 OR 7227F PIVOT SET 7215-7226-7227 Intermediate Pivot 7215F-7226F-7227F Intermediate Pivot 7215 Bottom Pivot 7215F Bottom Pivot 7226-Bottom Pivot 7226F-Bottom Pivot 7227-7227F-Bottom Pivot 7215-7226-7227PT Power Transfer Intermediate Pivot 3/4" Offset Pivots - Fire-Rated - 1000 to 1750 Lb. Doors 7230F-7237F Top Pivot Optional 7230F PIVOT SET 7237F PIVOT SET 7230F-7237F Intermediate Pivot 7230F Bottom Pivot 7237F Bottom Pivot B2

Wall Bumpers WS406CVX & WS407CVX WS406CCV & WS407CCV Features: Constructed in sturdy yet economical wrought base of brass, aluminum or stainless steel construction. Feature concealed tamper-proof mounting. Shipped factory preassembled backplate to reduce installation cost. Easy installation by inserting screwdriver through small hole in rubber. The WS406CVX unit is designed with a convex rubber bumper, packed with wood screw and plastic anchor. The WS406CCV unit is designed with a concave rubber bumper, which avoids damage to locks with projecting buttons, packed with wood screw and plastic anchor. The WS407CVX unit is designed with a convex rubber bumper packed with screw and drywall anchor. The WS407CCV unit is designed with a concave rubber bumper which avoids damage to locks with projecting buttons and is packed with screw and drywall anchor. WS406CVX & WS407CVX meets ANSI/BHMA 156.16 L22201 for brass, L42101 for aluminum and L52101 for stainless steel. WS406CCV &WS407CCV meets ANSI/BHMA 156.16 L22251 for brass and L42251 for aluminum, and L52251 for stainless steel. Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D, US28, US32D. Mounting Base Base Overall Product No. Hardware Diameter Thickness Projection Wood screw, WS406CVX plastic anchor 2-1/2" 3/8" 1" Wood screw, WS406CCV plastic anchor 2-1/2" 3/8" 1" Screw, Drywall WS407CVX Anchor 2-1/2" 3/8" 1" Screw, Drywall WS407CCV Anchor 2-1/2" 3/8" 1" WS406CVX & WS407CVX WS406CCV & WS407CCV D14

Door Silencers SR64 Features: For use on metal frames featuring pneumatic design that, once installed, forms an air pocket to absorb shock and reduce noise of door closing. Tamper-proof once installed on the frame. Proper installation also eliminates door rattle and provides constant tension for door latches or locks. Packed in bags of 100. Grey also available in bulk pack of 2500. Each bag has an installation tool included. Meets ANSI/BHMA 156.16, L03011. Finish: grey is standard. Black optional. Product No. Diameter Thickness SR64 1/2" 1/8" SR65 Features: For use on wood frames, also feature pneumatic design to cushion shock and absorb noise. To prevent removal, a small brad should be driven into stop strip and through stem of silencer, as shown in the detail. Packed in bags of 100. Meets ANSI/BHMA 156.16, L03021 Finish: grey. Product No. Height Width Thickness SR64 3/4" 3/8" 1/8" SR66 Features: Self Adhesive Rubber Silencers. Economical installation requires no drilling of frames. Packed in sheets of 100. Finishes: brown, grey, white. Product No. Diameter Thickness SR66 1/2" 1/8" D21

Residential Door Stops 060 and 061 Flexible Door Stops Features: Utilizes heavy gauge spring to maintain rigid protections. Simple to install - only a screwdriver required. Rubber tip is replaceable. Made from burnished wrought steel. Meets design requirements of ANSI/BHMA A156.16. Packed disassembled for quick installation. Finishes: F3, F5, F10, F10B, F14, F26, F26D. Product Number 060 3" 061 4" Projection 060 061 60, 61 and 62 Base Door Stops Features: Available in three sizes to accommodate varying areas of installation and door trim dimensions. Rubber tip is replaceable. 60 Base Door Stop Projection: 3-3/4". Made from solid brass or aluminum. Finishes: B3 (B-605), B4, B5, B10, B10B (B-613), B14, B15 (B-619), B15A (B-620), B26 (B-625), B26D, A3, A4, A5, A10, A10B, A14, A26, A92. 61 Base Door Stop Projection: 3-1/8" on brass units. 3-3/16" on aluminum units. Made from solid brass, aluminum, or epoxy colored aluminum. Finishes: B3 (B-605), B4, B5, B10, B10B (B-613), B14, B15 (B-619), B15A (B-620), B26 (B-625), B26D, A3, A4, A5, A10, A10B, A14, A26, A92, A-A (Almond Epoxy Coated), A-W (White Epoxy Coated), A-BLK (Black Epoxy Coated). 62 Base Door Stop Projection: 4-1/2". Made from solid brass or aluminum. Finishes: B3 (B-605), B4, B5, B10, B10B (B-613), B14, B15 (B-619), B15A (B-620), B26 (B-625), B26D, A3, A4, A5, A10, A10B, A14, A26, A92. 60 61 062 Base Door Stop Features: Base Door Stop features one-piece styling. Designed with a flat surface to accommodate wrench or pliers when installing. Rubber tip is replaceable. Made from solid brass or aluminum. Meets ANSI/BHMA A156.16. Finishes: B3 (B-605), B4, B5, B10, B10B (B-613), B14, B15 (B-619), B15A (B-620), B26 (B-625), B26D, A3, A4, A5, A10, A10B, A14, A26, A92. Product Number Projection 062 2-1/2" D22

Viewers Meets ANSI/BHMA A156.16 L23222 UL Listed 90 minute fire doors U696 One-Way Viewer 150 Angle of View. For doors 1-3/8" to 2-1/16" thick. Secure, tamper-resistant. Solid brass body; glass lens. Simple installation only a 1/2" hole required. Suggested installation height: 60" from floor. Trim washer available, 3/4" x.032" thick. Finishes Ives Number B4 B10B B26D BHMA 606 613 626 A Hinges & Pivots B Pulls & Plates 698 U698 One-Way Wide Angle Viewer 190 Angle of View. Lens projects 1/4" from face of door. 4 optical glass lenses. For doors 1-3/8" to 2-1/8" thick. Solid brass body and barrel. Simple installation only a 9/16" hole required. Suggested installation height: 60" from floor. C Flush Bolts & Coordinators D Latches, Catches & Bolts 698 meets ANSI/BHMA A156.16 L23172 U698 meets ANSI/BHMA A156.16 L23222 U698 is UL Listed 90 minute fire doors Finishes Ives Number B3 B15** B26D B716* BHMA 605 619 626 * not available on U698 ** only available in Schlage Carded E F5 Stops Exterior Hardware G Miscellaneous Hardware USA 1.877.613.8766 Canada 1.905.403.1800 www.ives.ingersollrand.com F5

Roller Latches RL30 Actuation is simple, closing of the door causes the roller to fall in the depression of the strike, thereby holding the door closed. The projection of the roller is easily adjusted using adjusting screws on the face of the unit. Maximum projection of the roller is 3/8" allowing for variance in the door clearance. Nylon Roller Standard. Forged Brass Construction. Meets ANSI/BHMA A156.16, E19091. Finishes: US3, US4, US10, US10B, US26, US26D. Optional Roller F Nylon covered brass roller. Optional Strike A ASA Dimensions: Body: 1" Wide x 3-3/8" Long x 1-11/16" Deep Strike: 1-11/16" Wide x 2-1/4" Long x 5/32" Thick Optional ASA Strike: STK726 (not shown): 1-1/4" wide x 4-7/8" long x 3/32" thick RL32 Actuation is simple, closing of the door causes the roller to fall in the depression of the strike, thereby holding the door closed. The projection of the roller is easily adjusted by turning knurled knob on back of latch. Maximum projection of the roller is 1/2" allowing for variance in the door clearance. Fits heavy-duty cylindrical lock cutout. Nylon Roller Standard. Non-handed. Brass or Stainless Steel Construction. Meets ANSI/BHMA A156.16, E19101. Finishes: US3, US4, US10, US10B, US32, US32D. Optional Roller F Nylon covered brass roller. Optional Strike A ASA. Dimensions: Body: 1-1/8" Wide x 2-1/4" Long x 2-1/4" Deep Strike: 1-1/8" Wide x 2-3/4" Long x 3/32" Thick Optional ASA Strike: STK726 (not shown): 1-1/4" wide x 4-7/8" long x 3/32" thick How to Order: RL - Model: 30 32 Roller Type: Blank Standard Nylon Roller F Nylon Coated Brass Roller Strike Type: Blank Standard Strike A ASA Strike Finishes: RL30 RL32 US3, US4, US10, US10B, US26, US26D US3, US4, US10, US10B, US32, US32D G1

Cabinet/Closet Knobs and Pulls 22 Flush Pull Low profile makes this pull ideal for louvered, bi-folding or wardrobe doors. Extra deep recess and reverse tapered grip provide for ease of pulling and gripping. Made from wrought brass. Conforms to design requirements of ANSI/BHMA A156.9 B22201 and A156.14 D2781. Finishes: B3, B4, B5, B10, B10B, B14, B15 (B-619), B15A (B-620), B19, B26 (B-625), B26D, B-619, B-620, B-625. Dimensions: 1-5/16" H x 3-1/8" W x 7/16" D 218 Finger Pull Ideal for use on sliding doors. Easy installation. Made from wrought brass. Conforms to design requirements of ANSI/BHMA A156.9 B22201 and A156.14 D2781. Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D. Dimensions: Inside Cup Diameter: 3/4" Overall Diameter: 1" Depth: 5/16" 220/221 Flush Pull Ideal for use on sliding doors. Built-in prong design eliminates the need for screws or brads and facilitates installation. Packed with two escutcheon pins for added holding power. Made from wrought brass. Conforms to design requirements of ANSI/BHMA A156.9 B22201 and A156.14 D2781. Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D. Dimensions: 220 Inside Cup Diameter: 2" 220 Overall Diameter: 2-3/8" 220 Depth: 7/16" 221 Inside Cup Diameter: 2-1/8" 221 Overall Diameter: 2-7/16" 221 Depth: 7/16" K5

Cabinet/Closet Knobs and Pulls 425/426 Flush Ring Pull Ideal for use on sliding doors. Convenient finger grip provides easy use of pull. Made from wrought brass. Conforms to design requirements of ANSI/BHMA A156.9 B22201. Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D. Dimensions: 425 Inside Cup Diameter: 1-1/2" 425 Overall Diameter: 1-3/4" 425 Depth: 3/8" 426 Inside Cup Diameter: 2-1/8" 426 Overall Diameter: 2-1/2" 426 Depth: 3/8" 42 Pocket Sliding Door Bolt Exclusive Ives design permits emergency release of bolt from outside the door. Spring activated design allows feather-touch action. Brass grommet supplied to cap release hole, protecting the door s finish. Made from wrought brass. Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D. Dimensions: Overall Size, Plate: 3-1/16" x 1-5/32" Strike: 1" x 3/4" Depth of Mortise: 5/8" 230 Sliding Door Edge Pull 3/4" width allows installation on narrow as well as standard doors. Spring automatically returns lever flush with plate. Made from solid brass. Conforms to design requirements of ANSI/BHMA A156.14 D2801. Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D. Dimensions: 3-7/8" H x 3/4" W K7

Protection Trim 8400 Series Protection Plates Door protection plates are available in.050 thick brass, stainless steel or aluminum; and 1/8 thick high impact polyethylene in clear or black. Bevel edge options; specify B4E for all four edges. Mounting screw pack furnished standard, 16 screws per pack. Optional screw packs are available for TEK or TORK screw heads. Refer to the following chart for ordering. Specify NMH for no mounting holes. Specify NMH-A for no mounting holes with adhesive. Specify CS for counter sunk mounting holes. Specify ERS prepped with extra row of screws. Kickplate Gasket Tape Tape is recommended when using a brass plate on a metal door to reduce tarnishing from electrolytic oxidation. One tape pack will cover an the perimeters of a 8 x 34 kickplate. Order 8401 Gasket Tape. A Hinges & Pivots B13 Pulls & Plates C Flush Bolts & Coordinators 8400 Protection Plate 8402 (UL)* Protection Plate *UL mark appears in upper right corner. Number of screw packs required by plate size (specify TEK Screws or TORK screws). 22"-25" 26"-33" 34"-41" 42"-48" 4"-8" 1 1 1 1 9"-16" 1 1 1 1 17"-24" 1 1 1 2 25"-32" 1 1 2 2 33"-40" 1 2 2 2 41"-48" 2 2 2 2 Finishes brass US Number US3 US4 US10 US10B US15 US26 US26D BHMA 605 606 612 613 619 625 626 Finishes stainless steel US Number US32 US32D BHMA 629 630 D Latches, Catches & Bolts E F Stops Exterior Hardware Finishes aluminum US Number US28 BHMA 628 Finishes plastic Clear and Black USA 1.877.613.8766 Canada 1.905.403.1800 www.ives.ingersollrand.com Residential Grade Kickplates available Carded only, finishes PA28, PA3, PA619, PA716, B3, B505, B619, B716 B13 G Miscellaneous Hardware

Protection Trim A Hinges & Pivots G Miscellaneous Hardware F Exterior Hardware B14 Pulls & Plates C Flush Bolts & Coordinators D Latches, Catches & Bolts E Stops Mop Plates Protect the bottom of the pull side of door subject to cleaning and mopping procedures. Size Ranges:4" to 6" high, 22" to 48" wide Kick Plates Protect the bottom of the push side of doors subject to scuffing from foot traffic. Recommended for all doors subject to normal use (especially doors using a closer). Size Ranges: 8" to 24" high, 22" to 48" wide Stretcher Plates Protect doors at specific areas where consistent contact is made by stretchers, service carts or other equipment. Usually applied to push side of doors. Specify B4E Option for beveled edges. Size Ranges: 6" to 8" high, 22" to 48" wide Armor Plates Protect lower half of doors from abuse by hard carts, trucks and rough usage. Usually applied to push side of single doors and both sides of double acting doors. Size Ranges: 26" to 48" high, 22" to 48" wide B14 USA 1.877.613.8766 Canada 1.905.403.1800 www.ives.ingersollrand.com

Full Mortise Hinges - 5 Knuckle 5PB1 5 Knuckle, Plain Bearing PLAIN BEARING LOW FREQUENCY STANDARD WEIGHT For use on Standard Weight Doors with Low Frequency Usage, not intended for use with door closing devices. 5PB1 Steel with steel pin 5PB1 Brass with stainless steel pin 5PB1 Stainless steel with stainless steel pin (630 finish) NRP = Non-Removable Pin Dimensions & tolerances conform to ANSI - A156.7 Packed with wood and machine screws 5PB1 Steel description conforms to ANSI - A8133 5PB1 Brass conforms to ANSI - A2133 5PB1 Stainless Steel description conforms to ANSI - A5133 Size (Inches) Size (mm) Gauge 3.5 x 3.5 89 x 89 0.123 4.5 x 4 114 x 102 0.134 4.5 x 4.5 114 x 114 0.134 A R C H I T E C T U R A L H I N G E S 5BB1 5 Knuckle, Ball Bearing 2 BALL BEARING MEDIUM FREQUENCY STANDARD WEIGHT For use on Standard Weight Doors with Medium Frequency Usage 5BB1 Steel with steel pin 5BB1 Brass with stainless steel pin 5BB1 Stainless steel with stainless steel pin (630 finish only) NRP = Non-Removable Pin Dimensions & tolerances conform to ANSI - A156.7 5BB1 Steel description conforms to ANSI - A8112 5BB1 Brass conforms to ANSI - A2112 5BB1 Stainless description conforms to ANSI - A5112 Packed with wood and machine screws Size (Inches) Size (mm) Gauge 4 x 4 102 x 102 0.130 4.5 x 4 114 x 102 0.134 4.5 x 4.5 114 x 114 0.134 4.5 x 5 114 x 127 0.146 5 x 4.5 127 x 114 0.146 5BB1RC 5 Knuckle, Ball Bearing, Round Corner 2 BALL BEARING MEDIUM FREQUENCY STANDARD WEIGHT For use on Standard Weight Doors with Medium Frequency Usage 5BB1 Steel with steel pin NRP = Non-Removable Pin Dimensions & tolerances conform to ANSI - A156.7 1/4" radius 5BB1 Steel description conforms to ANSI - A8112 Packed with wood and machine screws Size (Inches) Size (mm) Gauge 3.5 x 3.5 89 x 89 0.123 4.5 x 4 114 x 102 0.134

1500 Commercial Grade Pocket Door Frame for 1 to 13/8 Thick Doors (13/4 with 1575 Adaptor Kit) to 125 lbs. (200 lbs. with 1125 Hanger) ORDERING DATA 3/4" (19mm) 3/16" (5mm) 1500 DOOR HEIGHT + 4-1/2" (114mm) For 2 x 4 Construction. Removable aluminum track with convex rails for smooth quiet operation, rust resistant steel reinforced wood split studs, jump proof three wheel (1 dia.) hangers, self adjusting floor anchors, 2 6 and 3 0 headers marked to cut to smaller door sizes. Brass-tone steel parts. All frames for doors up to 13/8 can be converted for 13/4 doors with 1575PPK3 adaptor kit. All oversized frames include 1575PPK3 adaptor kit. Item No. Description lbs/case Accessories 1500PPK3 Replacement Hardware Kit 5/10 1555PPK3 Converging Door Kit 3/10 1575PPK3 1-3/4 Door Adapter Kit 3/10 Steel Wrapped Uprights Please Note: 3 6 and 4 0 Frames have 1 extra pair of uprights. 4 6 and 5 0 Frames have 2 extra pairs of uprights. 1568UPRT 80 Upright Pair with 13/8 Floor Bracket 72/6 1570UPRT 84 Upright Pair with 13/8 Floor Bracket 75/6 1580UPRT 96 Upright Pair with 13/8 Floor Bracket 86/6 *1590UPRT* 108 Upright Pair with 13/8 Floor Bracket 96/6 Hangers 1120 Standard Hanger, max weight 125 lbs. 13/50 1125 Ball-Bearing Hanger, max weight 200 lbs. 23/50 1121 Hanger Plate w/ screws 9/100 1500 Series Pocket Door Frame Prices Item No. Max Door Size lbs/case Frames for 80 Tall Doors up to 125 lbs. 152068PF For Doors up to 24 wide x 80 tall x 13/8 28/1 152468PF For Doors up to 28 wide x 80 tall x 13/8 29/1 152668PF For Doors up to 30 wide x 80 tall x 13/8 30/1 152868PF For Doors up to 32 wide x 80 tall x 13/8 30/1 153068PF For Doors up to 36 wide x 80 tall x 13/8 30/1 Frames for 80 Tall Doors up to 200 lbs. (Uses 1125 Ball Bearing Hanger) 152068HD For Doors up to 24 wide x 80 tall x 13/8 28/1 152468HD For Doors up to 28 wide x 80 tall x 13/8 29/1 152668HD For Doors up to 30 wide x 80 tall x 13/8 30/1 152868HD For Doors up to 32 wide x 80 tall x 13/8 30/1 153068HD For Doors up to 36 wide x 80 tall x 13/8 30/1 Frames Below include 1575 13/4 Adaptor Kit 153668PF For Doors up to 42 wide x 80 tall x 13/4 40/1 154068PF For Doors up to 48 wide x 80 tall x 13/4 42/1 *154668PF* For Doors up to 54 wide x 80 tall x 13/4 54/1 *155068PF* For Doors up to 60 wide x 80 tall x 13/4 55/1 Frames for 84 Tall Doors up to 200 lbs. (Uses 1125 Ball Bearing Hanger) 152070PF For Doors up to 24 wide x 84 tall x 13/4 32/1 152470PF For Doors up to 28 wide x 84 tall x 13/4 34/1 152670PF For Doors up to 30 wide x 84 tall x 13/4 35/1 152870PF For Doors up to 32 wide x 84 tall x 13/4 37/1 153070PF For Doors up to 36 wide x 84 tall x 13/4 39/1 153670PF For Doors up to 42 wide x 84 tall x 13/4 43/1 154070PF For Doors up to 48 wide x 84 tall x 13/4 50/1 *154670PF* For Doors up to 54 wide x 84 tall x 13/4 57/1 *155070PF* For Doors up to 60 wide x 84 tall x 13/4 61/1 Frames for 96 Tall Doors up to 200 lbs. (Uses 1125 Ball Bearing Hanger) 152080PF For Doors up to 24 wide x 96 tall x 13/4 35/1 152480PF For Doors up to 28 wide x 96 tall x 13/4 39/1 152680PF For Doors up to 30 wide x 96 tall x 13/4 40/1 152880PF For Doors up to 32 wide x 96 tall x 13/4 41/1 153080PF For Doors up to 36 wide x 96 tall x 13/4 43/1 153680PF For Doors up to 42 wide x 96 tall x 13/4 44/1 154080PF For Doors up to 48 wide x 96 tall x 13/4 50/1 *154680PF* For Doors up to 54 wide x 96 tall x 13/4 59/1 *155080PF* For Doors up to 60 wide x 96 tall x 13/4 62/1 Frames for 108 Tall Doors up to 200 lbs. (Uses 1125 Ball Bearing Hanger) *152090PF* For Doors up to 24 wide x 108 tall x 13/4 38/1 *152490PF* For Doors up to 28 wide x 108 tall x 13/4 40/1 *152690PF* For Doors up to 30 wide x 108 tall x 13/4 41/1 *152890PF* For Doors up to 32 wide x 108 tall x 13/4 42/1 *153090PF* For Doors up to 36 wide x 108 tall x 13/4 44/1 *153690PF* For Doors up to 42 wide x 108 tall x 13/4 56/1 *154090PF* For Doors up to 48 wide x 108 tall x 13/4 62/1 *154690PF* For Doors up to 54 wide x 108 tall x 13/4 72/1 *155090PF* For Doors up to 60 wide x 108 tall x 13/4 80/1 11

Multiple-Door Sliding Door Hardware 200MD, 100MD, 111MD Shown below are typical 3 track layouts for 1-3/8 doors. Other door thicknesses may be used. For thicker doors, the tracks must be spaced further apart and a wider header may be necessary. Also, more than 3 tracks may be used by extending the header and using other track combinations as required. 200MD Series-300 lbs. Doors 6-1/2" (165mm) Header 200 200 200 1-3/8" Door 1-3/8" Door 1-3/8" Door (35mm) (35mm) (35mm) 100MD Series-200 lbs. Doors 5-1/4" (133mm) Header 100 100 100 1-3/8" Door 1-3/8" Door 1-3/8" Door (35mm) (35mm) (35mm) 111MD Series-150 lbs. Doors 3-1/8" MIN. (79mm MIN.) 3-7/8" MAX. (98mm MAX.) 1-3/4" MIN (45mm MIN 2-1/4" MAX (57mm MAX 6, 8, and 9 Sets Utilizing 200, 100, and 111 Hardware Sets. 200MD Series Hardware Sets- 300lbs Doors (min 1-1/8 thick) Set Image Part # Track Length 200M0723 70 1829mm 200M0963 94 2438mm 200M1083 106 2692mm 200M1443 142 3657mm Max Door Width (ea) 24 x 3 610mm x 3 32 x 3 813mm x 3 36 x 3 914mm x 3 48 x 3 1219mm x 3 Max Door Weight (ea) 300 lbs. 136 kgs. 300 lbs. 136 kgs. 300 lbs. 136 kgs. 300 lbs. 136 kgs. Set consists of 3-200 tracks, 3-1050 bottom tracks, 6-2020 hangers, 6-1705 guides, and 2-2055 track stops. 100MD Series Hardware Sets- 200lbs Doors (min 1 thick) Set Image Part # Track Length 100M0723 70 1829mm 100M0963 94 2438mm 100M1083 106 2692mm 100M1443 142 3657mm Max Door Width (ea) 24 x 3 610mm x 3 32 x 3 813mm x 3 36 x 3 914mm x 3 36 x 3 1219mm x 3 Max Door Weight (ea) 200 lbs. 91 kg. 200 lbs. 91 kg 200 lbs. 91 kg 200 lbs. 91 kg Set consists of 3-100 tracks, 3-1050 bottom tracks, 6-1125 hangers, 6-1705 guides, and 2-1155 track stops. 1/4" (6.4mm) 5-1/4" (133mm) Header 111 111 111 1/2" (12.5mm) 1/2" (12.5mm) 1-3/8" Door 1-3/8" Door 1-3/8" Door (35mm) (35mm) (35mm) 1-9/16" MIN (40mm MIN 1-7/8" MAX (48mm MAX 1050 Bottom Track- Included w/ all Sets 1/4 ROUND OR CARPET 1-3/8" Door 1-3/8" Door 1-3/8" Door (35mm) (35mm) (35mm) 1705 1705 1705 HARD HARD WOOD WOOD 3/4" X 1-1/8" 3/4" X 1-1/8" (19mm X 29mm) (19mm X 29mm) (200 SERIES 3/4" x 1-1/4" (19mm X 32mm)) 1-3/8" (35mm) 1-7/16" (37mm) 1/4 ROUND OR CARPET All nosing and hardware filler supplied by others. Surface mount shown/ Bottom channel may be recessed into floor. Spacing and dimensions will vary with other door thicknesses. Tracks can be cut down for smaller openings. 24 111MD Series Hardware Sets- 150lbs Doors (min 3/4 thick) Set Image Part # Track Length 2054 PLBG MULTI PULL CATCH 2054PLBG 111M0723 70 1829mm 111M0963 94 2438mm 111M1083 106 2692mm 111M1443 142 3657mm Max Door Width (ea) 24 x 3 610mm x 3 32 x 3 813mm x 3 36 x 3 914mm x 3 48 x 3 1219mm x 3 Max Door Weight (ea) 150 lbs. 68 kgs. 150 lbs. 68 kgs. 150 lbs. 68 kgs. 150 lbs. 68 kgs. Set consists of 3-111 tracks, 3-1050 bottom tracks, 6-1025 hangers, 6-1705 guides, and 2-1155 track stops. Multi Pull Catch

National Guard Products, Inc. PROTECTION, INSIDE OUT Toll Free Phone 1-800-647-7874 Toll Free Fax 1-800-255-7874 Self Adhesive Seals Self Adhesive Seals ESS 10C 1/4" 1/2" 5050B Brown 5050C Charcoal 5050W White 5050T Tan 5050CL Clear S Silicone JAMB JAMB Sealing System on 20 min **Edge rated wood doors up to 4 0 x 8 0 single, 8 0 x 8 0 std. pair with 9800 or 9500 at meeting edge. Available in 17, 20, 21, 25 and 300 rolls. HEAD & LATCH SIDE DOOR DOOR HINGE SIDE 1/4" 3/8" 2525B Brown 2525C Charcoal 2525W White 2525T Tan 10C S Silicone Available in 17, 20, 21, 25 and 300 rolls. JAMB (optional astragal application) JAMB HEAD & LATCH SIDE DOOR DOOR HINGE SIDE 1/2" 5060B Brown 5060CL Clear 10C S 5/16" Available in 7, 8, 9, 17, and 21 rolls Neoprene Gasketing 7/16" 7/16" 11/32" 7/16" width thickness 361 18, 21, 50 rolls 3/8 x 3/16 362 18, 50 rolls 1/2 x 1/4 363 18, 50 rolls 3/8 x 1/8 5020B Brown 5020C Charcoal 5020W White 7/16" Kerf Application 5021B Brown 5021C Charcoal LATCH SIDE DOOR HINGE SIDE DOOR 5021W White 10C S Available in 36, 48, 84, 96 and 108 lengths. FATT Fast Attach Two-Way Tape Fast attach two way tape provides an easy and effective alternative to gasketing installation. A 1/2 wide 2-way tape is applied to the metal housing insuring a quick and easy installation. Then for security, 3 tek-type self drilling screws are used to further secure each piece of material to the frame stop. A no problem installation with no holes to drill. To order add suffix FATT to product number. See price list for products available with this feature. FATT IS NOT CLASSIFIED FOR USE ON FIRE DOORS. 50 E-mail: ngpinfo@ngpinc.com www.ngpinc.com

National Guard Products, Inc. PROTECTION, INSIDE OUT Toll Free Phone 1-800-647-7874 Toll Free Fax 1-800-255-7874 Wild Hair - Nylon Brush Seals C627A C627B C627DKB 10C 1 7/16" 9/16" A605A A605B A605DKB 10C S 600 600A 600B 600DKB 10C B606A B606B B606DKB 7/8" 1/2" 601 601A 601B 601DKB 10C 7/8" 1" OV633A OV633B OV633DKB 602A 602DKB S 10C 7/8" 1/2" OV634A OV634B OV634DKB 603A 603DKB 10C 7/8" 1" A617A 10C.45 O S 1/2" 7/16" All Products this page. #6 x 3/4 Stainless Steel Sheet Metal Screws furnished. 5 1/2" S 5/8" 10C 3/4" 10C 5/8" 10C 7/16" C607A C607B C607DKB 1 1/16" 9/16" 3/4" 1/2" 1 3/16" 1" 1 9/16" 1 3/8" 1 3/4" 5 1/2" 1 3/4" 5/8" 10C 10C 10C 10C 1" 10C 3/4" 2 1/2" 1 3/8" 1 3/8" 4" 2 1/2" 5 1/2" 4" 56 D608A D608B D608DKB E609A E609B E609DKB G610A G610B G610DKB H612A H612B H612DKB I-615A I-615B I-615DKB G611A G611DKB H614A H614DKB E-mail: ngpinfo@ngpinc.com I-616A I-616DKB

National Guard Products, Inc. PROTECTION, INSIDE OUT Toll Free Phone 1-800-647-7874 Toll Free Fax 1-800-255-7874 Specialty Astragals, Drip Strips, Overhead Door Bottom Seal 1 3/4" 14RA 14RB 14RDKB Available for 2 1/4 door- specify 112N 112NDKB 1 3/16" Security Astragal black rubber covered fabric astragal Max. 1 1/2" 5/32" 96" MAXIMUM HEIGHT 23/32" neoprene Drip Strips 1 1/2" 5/8" 16A 16B 16DKB Overhead Door Bottom Seal 81369N 81369NDKB 1 1/8" 17 17DKB 2 1/2" 3/4" 1/4" 1 1/2" detail 1/2 size 145PA 145PB 145PDKB Spring loaded protection for pairs of outswinging doors up to 96 in height. Pile insert for weather protection, sturdy aluminum for pry bar protection. Glass Door Astragal Seals Our glass door seal consists of translucent PVC channel and nylon brush for an attractive solution to a difficult problem. 15/16" 15/16" 15/16" 5/8" 1/2" 5/8" 1/2" 2 3/4" neoprene 1/8" #8 x 1 1/4" Stainless Steel Screw 66 nylon brush A650 A651 5/8" 7/16" 7/16" 5/8" Order as set to receive two pieces Maximum length120 E-mail: ngpinfo@ngpinc.com 7/16" www.ngpinc.com nylon brush

National Guard Products, Inc. PROTECTION, INSIDE OUT Toll Free Phone 1-800-647-7874 Toll Free Fax 1-800-255-7874 Offset Thresholds 10C All products this page. 653.78 lbs./ft. 653DKB.78 lbs./ft. 5 1/2" Typical Wall.125 1/4" 1/2" 1/4" 1/4" 655.84 lbs./ft. 655DKB.84 lbs./ft. Typical Wall.125 1/2" 3/4" 5 1/2" 656 1.00 lbs./ft. 656DKB 1.00 lbs./ft. Typical Wall.125 1/2" 1/2" 1" 6" 659.89lbs./ft. 659DKB.89 lbs./ft. Typical Wall.125 1/2" 1/4" 7" Carpet Dividers/Carpet Edges Carpet Dividers 414.31 lbs./ft. 414DKB.31 lbs./ft. 403.70 lbs/ft. Typical Wall.125 403DKB.70 lbs./ft. 404.70 lbs./ft. 404DKB.70 lbs./ft. 4" Typical Wall.125 4" 1 3/4" Typical Wall.141 3/8" 1/2" 3/8" Carpet Edges 416.19 lbs./ft. 417.50 lbs./ft. 417DKB.50 lbs./ft. Typical Wall.125 1 7/16" Typical Wall.188 2 1/2" 3/4" 1/2" 3/8" Typical Wall.125 404-75.80 lbs./ft. 404-75DKB.80 lbs./ft. 4" 3/4" 1 3/4" 414-75.39 lbs./ft. 414-75DKB.39 lbs./ft. 16 409 1.20 lbs./ft. 409DKB 1.20 lbs./ft. E-mail: ngpinfo@ngpinc.com 6" Typical Wall.125 www.ngpinc.com 1/2"

National Guard Products, Inc. PROTECTION, INSIDE OUT Toll Free Phone 1-800-647-7874 Toll Free Fax 1-800-255-7874 Neoprene Door Shoes 3/4" 1/2" 1/4" 15NA 15NB 15NDKB 1 3/4" neoprene 26NA 26NDKB 1 3/4" A - clear B -gold DKB - dark bronze neoprene is black neoprene 1 " 23/32" All products this section: OK for use on S label doors. 112N 112NDKB 1 3/16" 10C neoprene 23/32" Door Shoes - Neoprene 1 3/4" neoprene 113NA 113NDKB 1 3/16" 1/4" 3/4" 1/4" 1/2" neoprene 118NA 118NDKB 23/32" 1" 119N 119NA 119NB 119NDKB neoprene 1 " 23/32" Door Bottom Seals 1 3/4" 23/32" 3/8" 3/16" 5/16" 116N 116NDKB neoprene 1 1/4" 14RA 14RB 14RDKB rubber covered fabric 3/4" neoprene 136N 136NDKB 3/16" 1/4" Available for a 2 1/4 door - specify Mortise 7/16 wide x desired depth. #4 SMS furnished. Pile Door Shoes #6 x 3/4 stainless steel sheet metal screws furnished. 154P 154PDKB 1 3/4" E-mail: ngpinfo@ngpinc.com gray pile 3/8" 1" 5/32" 254P 254PDKB 1 7/16" www.ngpinc.com gray pile 3/8" 67

FA-Series and F-Series Residential Lock Sets Knob/Lever Design Options FA-Series 2-3/4" 70 mm Andover 2-5/16" 59 mm 2-1/4" 57 mm Danbury 2-3/4" 70 mm 2-3/8" 60 mm 2-9/16" 65 mm St. Annes 2-3/4" 69 mm 2-1/2" 64 mm 4-7/8" 123 mm 2-3/4" 69 mm 4-1/2" 114 mm 2-3/4" 69 mm 4-13/16" 123 mm 2-3/4" 69 mm 4-1/ 105 Callington 2-1/4" 57 mm French Door Escutcheon Champagne 2-7/16" 62 mm FINISHES Merano 2-5/8" 123 mm See page 25 for Finish Samples Shown with Champagne Lever FRENCH DOOR ESCUTCHEON As a decorative option, French door escutcheons can be added to any F/FA-Series knob or lever function, except for keyed levers (F51/FA51). The French door escutcheons do come standard on the FA patio knob function (FA30). ADA-COMPLIANT PRODUCTS In compliance with the American National Standards Institute (ANSI A117.1) and the Americans with Dis abil i ties Act (ADA), Schlage Lock Company offers a wide selection of locks designed for the needs of the physically challenged. These solid lever designs are available as inside trim on handlesets. Knobs 505 605 609 613 619 620 622 625 626 716 Siena Plymouth Georgian Orbit Bell Andover Danbury Levers Avanti Accent Flair Manhattan Jazz Elan Callington Champagne Merano St. Annes DOOR PREPARATION 2-1/4" 57 mm 2-3/8" 1" 60 mm 25 mm = Helps meet LEED certification = Complies with ADA Accessibility Guidelines 1" dia. 25 mm 2-1/8" 54 mm 26 U.S.A. 1.800.847.1864 Canada 1.905.403.1800 www.schlage.com

CS 210/RS 210 Series Interconnected Lock Introducing the Schlage Interconnected lock. The new Schlage CS and RS 210 Interconnected Locks combine exclusive options with increased strength, for both residential and commercial applications. The Schlage CS and RS 210 feature single motion egress to meet Life and Safety code requirements, as well as adjustability from the standard 4 to 5-1/2 door preps. Robust performance exceeds BHMA grade 2 requirements, giving the CS and RS 210 the combination of aesthetics, versatility and strength. Features and Benefits Reliable: Meets all ANSI/BHMA A156.25 Grade 2 requirements 3 hr. UL fire rating Field Configurable: Works with door prep of 4 or 5-1/2 Adaptable: 15 Levers styles 2 Escutcheon styles 6 Finishes Flexible: FE210: Electronic Deadbolt RS210: B60 Trim CS210: B500 Trim SFIC and FSIC

Lever Styles Jazz Elan Jupiter Callington Merano Manhattan Neptune Champagne Escutcheon Styles Avila Avanti Flair Saturn St. Annes Accent Specifications 4 to 5 1/2 adjustable door prep Plymouth Escutcheon Decorative Camelot Escutcheon Deadbolt Choices 3 styles - (2) for mechanical security (1) for electronic Mechanical Electronic CS200 Latitude RS200 FE200 Cylinder Choices - available for CS 200 Series only 3 options - standard, full size or small format interchangeable core Full Size Interchangeable Core ANSI/BHMA Grade 2 certified UL Rating UL 3hr. rating is standard Latch UL latch comes with 1 x 2-1/4 square and round corner faceplate (square corner standard, round corner included in package). 1 edge bore required. Strikes 1-1/8 x 2-3/4 square corner deadbolt strikes and 2-1/4 x 1-5/8 square corner full lip latch strike reinforcer. Dust box not included. Backset Adjustable backset, fits 2-3/8 or 2-3/4 backsets Levers All lever trim is non-handed and field reversible Stile width Minimum 4-1/2 for 2-3/8 backset, minimum 5 stile for 2-3/4. To ensure proper fit, use the dimensions below Return to Door Saturn (SAT) and Neptune (NEP) levers are return to door code compliant Cylinder FE & RS Series Standard: 6 pin solid brass, keyed 5-pin CS Series Standard: 6 pin solid brass, keyed 5-pin, C123 keyway Optional: FSIC (full size interchangeable core), SFIC (small format interchangeable core) Keys (2) Silver nickel keys included Door Range 1-3/8 to 1-3/4 standard. 1-3/4 to 2 optional. Must be specified Center to Center Fits 4 or 5-1/2 center to center door preps. *Credential Deadbolt is operated using ibutton credential (sold separately) *Note: Only available on the FE200. Small Format Interchangeable Core Finishes 605 Bright Brass 609 Antique Brass 619 625 Satin Nickel Bright Chrome 877-671-7011 schlage.com 626 Satin Chrome 716/643e Aged Bronze 2012 Ingersoll Rand 005085 01/12

Cylinder Only Compr. Ring & Spring With Blocking Ring

6210, 6211, 6211AL, 6211WF ELECTRIC STRIKES 6210 Electric strike for use with mortise locks without deadbolt on single door, hollow metal frame applications and using ANSI prep at standard height, Strike pocket inserts are provided to accommodate different manufacturers deadlocking trigger locations. 6211 Electric strike for use with mortise locks without deadbolt or cylindrical locks on single door, hollow metal frame applications. Designed to replace Von Duprin 3140 or Folger Adam 712. 6211AL Electric strike for use with mortise locks without deadbolt or cylindrical locks on single door, aluminum frame applications. Designed to replace Folger Adam 722. 6211WF Electric strike for use with mortise locks without deadbolt or cylindrical locks on single door, wood frame applications. Designed to replace Folger Adam 732. FEATURES All Stainless Steel Construction Accepts 3 /4 (19mm) Throw Latchbolt Six Finishes Non-handed Fail Secure Horizontally Adjustable Plug Connectors OPTIONS Fail Safe Dual Monitor Switches Entry Buzzer VON DUPRIN VON DUPRIN VON DUPRIN VON DUPRIN 6210 6211AL VON DUPRIN VON DUPRIN 6211 VON DUPRIN SPECIFICATIONS 12V 24V Resistance in Ohms 10% @ 70 F 21 72 Watt-seated @ 70 F 7.5 8 Amps-seated @ 70 F.6.33 Amps-inrush @ 70 F.6.33 UL listed Burglary Resistant CVXY and Electric Strike for fire doors or frames GXAY (fail secure only). ANSI E59321 VON DUPRIN 6211WF DIMENSIONS AND CONFIGURATIONS 6210 6211 6211AL 6211WF 4 7 /8 (124mm) 1 3 /8 (35mm) 1 1 /4 (32mm) 1/2 (13mm) 7/8 (22mm) 1 3 /4 (44mm) 3 3 /8 (86mm) 3 1 /4 (83mm) 1/8 (3mm) 1 7 /16 (37mm) 12 (305mm) Minimum Clearance 1 1 /4 (32mm) 4 7 /8 (124mm) 1 1 /4 (32mm) 7/8 (22mm) 1/2 (13mm) 1 11 /16 (43mm) 3 3 /8 (86mm) 2 1 /16 (52mm) 1/8 (3mm) 1 15 /32 (49mm) 12 4 7 /8 (305mm) (124mm) Minimum Clearance 7/8 (22mm) 1 1 /4 (32mm) 1 1 /4 (32mm) 1 11 /16 (43mm) 3 3 /8 (86mm) 2 1 /16 (52mm) 1/2 1/8 (13mm) (3mm) 1 15 /32 (49mm) 12 4 (305mm) 7 /8 (124mm) Minimum Clearance 1 1 /4 (32mm) 7/8 (22mm) 3 3 /8 (86mm) 2 1 /16 (52mm) 1/8 (3mm) 1 15 /32 (49mm) 4 1 /2 (114mm) 3 9 /16 (90mm) Minimum Clearance 7

98/99 Rim Exit Device 299 Strike 98 and 99 rim exit devices for all types of single and double doors with mullion, UL listed for Panic Exit Hardware. Devices are ANSI A156.3 2001 Grade 1. The 98 device has a smooth mechanism case and the 99 device has a grooved case. The rim device is non-handed except when the following device options are used: SD (Special Dogging), -2 (Double Cylinder) or SS (Signal Switch). See Opposite page for available outside trim and device functions. Covers stock hollow metal doors with 86 or 161 cutouts on single doors (may cover cutouts on pairs consult template). The 98/99 devices are available in the following finishes: US3, US4, US10, US26, US26D, US28, 313AN, 315AN and US32D for the 98 device only. See page 52 for component finishes and the inside cover for finish chips. Specifications Device Functions Device ships EO/DT/NL. Field selectable. For TP,K,or L remove NL drive screw from device Device Lengths 3 2 4" to 3 (711mm to 914 mm) Door Size 4 2 10" to 4 (864 mm to 1219 mm) Door Size Strikes 299 Dull Black Optional Strikes see page 39 Dogging Feature Hex key dogging standard Dogging Options CD Cylinder Dogging see page 48 SD Special Center Case Dogging see page 48 LD Less Dogging see page 48 Electric Options LX Latchbolt Monitor Switch see page 42 RX Pushpad Monitor Switch see page 42 RX2 Double Pushpad Monitor Switch see page 42 E Electric Locking & Unlocking see page 44 EL Electric Latch Retraction see page 43 SS Signal Switch see page 43 CX Chexit Delayed Exit see page 45 ALK Alarm Exit Kit see page 42 Miscellaneous Options PN Pneumatic Latch Retraction see page 48-2 Double Cylinder see page 48 GBK Glass Bead Kit see page 49 Fasteners & Includes 1 ³ ₄" (19mm) 2 ¹ ₄" (57mm) Wood & Metal Doors Sex Bolts (SNB) Optional SNB available for device, see next page for quantities Latch Bolt Device Centerline from Finished Floor Center Case Dimensions Mechanism Case Dimensions Projection Deadlocking, ³ ₄" (19mm) throw 39 ¹³ ₁₆" (1011 mm) 39 ¹¹ ₁₆" (1008 mm) with Mullion 8" x 2 ³ ₄" x 2 ³ ₈" (203mm x 70mm x 60mm) 2 ¹ ₄" x 2 ¹ ₄" (57mm x 57mm) Pushbar Neutral 3 ¹³ ₁₆" (97 mm) Pushbar Depressed 3 ¹ ₁₆" (78 mm) See page 53 for How to Order specification 4 2004 Ingersoll-Rand. May be copied for use with specification submittal.

98/99 Rim Exit Device Standard Trim Exit only Dummy Trim Night Latch Night Latch Pull when Dogged Key Retracts Latchbolt Key Retracts Latchbolt Optional Pull Required Product Description Trim Description Escutcheon Plate Size Pull Center to Center Projection ANSI Function Cylinder Type Optional Trim (See pages 32 34) Optional #425 Sex Bolt Quantity for Device 98EO 98DT 98NL 98NL-OP 99EO 99DT 99NL 99NL-OP 990DT 990NL-R/V 110NL-MD 110NL-WD 3" x 14³ ₁₆" x ³ ₃₂" 3" x 14³ ₁₆" x ³ ₃₂" (76x360x2mm) (76x360x2mm) 5¹ ₂" (140mm) 5¹ ₂" (140mm) 2" (51mm) 2" (51mm) 01 02 03 03 Rim Rim x990eo x991k-dt x991k-nl x992eo x992l-dt x992l-nl x994eo x994l-dt x994l-nl x996eo x996l-dt x996l-nl x696dt x696nl x697dt x697nl 6 2 2 6 Lever Lever Night Latch Lever Blank Escutcheon Lever Dummy Trim Key Locks & Unlocks Key Retracts Latchbolt Always operable Pull when Dogged (No Cylinder) Product Description Trim Description Escutcheon Plate Size Pull Center to Center Projection ANSI Function Cylinder Type Optional Trim (See pages 32 34) 98L 98L-NL 98L-BE 98L-DT 99L 99L-NL 99L-BE 99L-DT 996L-R/V 996L-NL-R/V 996L-BE-R/V 996L-DT-R/V 2³ ₄" x 10³ ₄" x ²⁷ ₃₂" 2³ ₄" x 10³ ₄" x ²⁷ ₃₂" 2³ ₄" x 10³ ₄" x ²⁷ ₃₂" 2³ ₄" x 10³ ₄" x ²⁷ ₃₂" (70x273x21mm) (70x273x21mm) (70x273x21mm) (70x273x21mm) 2⁷ ₈" (73mm) 2⁷ ₈" (73mm) 2⁷ ₈" (73mm) 2⁷ ₈" (73mm) 08 09 02 Rim Rim x992l x992l-nl x992l-be x992l-dt x994l x994l-nl x994l-be x994l-dt Optional #425 Sex Bolt Quantity for Device For optional trims and functions see pages 32-34 2 2 2 2 5

Alarmed Exit Devices Chexit Controlled Exit Device CX33A/CX35A CX98/CX99 Rim device shown Refer to Chexit Catalog for complete selection information. CX Chexit is designed for use on delayed exit applications. The Chexit system is ideal for controlled areas. This concept in delayed exit systems combines life safety with the needs of security and meets all requirements of NFPA 101 for Special Locking Arrangement. The Chexit system will keep an exit door secured for a 15 second period, yet tied into the fire alarm system will release immediately when an alarm condition exists. All controls, auxiliary locking, local alarm, and remote signaling output are self-contained in the Chexit assembly, providing safe, secure and easy to install door control hardware. The Chexit system is ideal for highly controlled areas such as airports, hospitals, government facilities and development labs, retail stores, libraries and security facilities. CX98 and CX99 are available for rim, mortise lock and surface and concealed vertical rod mounting styles. CX33A and CX35A are available on rim mounting style only. For CX98/9927 and CX98/9957 Panic and Fire Devices, two Rod Guards (RGO) are required. For door heights over 7 additional Rod Guards (RGO) will be added as needed to protect the rods. UL listed for use on panic or fire exit doors 3 or 4 wide. The Chexit device includes decal for application on door, PUSH UNTIL ALARM SOUNDS. DOOR CAN BE OPENED IN 15 SECONDS. A complete Chexit system requires a PS873 power supply and a power transfer. See pages 28 and 29. FEATURES Non handed Field sizable 3 4 (19mm) throw, latch bolt Deadlocking 20 Request to Exit Switch is built in to detect when someone attempts to exit. Applying less than 15 pounds to the push pad will cause this switch to start an irreversible alarm cycle. Nuisance Alarm When the Nuisance Audible and Nuisance Delay options are set to off the device will go into alarm as soon as the push pad is touched. Turning the Nuisance Delay on will require the push pad to be pressed for 2 seconds before the Chexit goes into alarm, which is ideal in public areas. If the Nuisance Audible and Nuisance Delay are both on, the alarm will sound as soon as the push pad is pressed, but the alarm sequence will stop unless held for 2 seconds or more. Remote Alarm A set of relay contacts (rated 1 ampere, 24VDC) are provided to give external alarm indication. These contacts close when the device is in an irreversible alarm condition. These contacts can be used to drive a horn, lamp, or other signaling devices. Key Switch The Key Switch provides the means to arm, disarm, or reset the Chexit. The key can be removed in either the Arm or Disarm position. Indicator Lamp The Indicator Lamp determines the status of the Chexit. When the lamp is off, it indicates disarmed and is functioning as a normal exit device. A slow flashing lamp indicates armed. A fast flashing indicator lamp indicates the device is in alarm. Internal Horn Whenever the device is in alarm or the push pad is pressed the Internal Horn will sound. The volume level of this horn exceeds 85 db at 6 feet. Door Position Input An external door position switch can be connected to the Chexit. The door position switch will cause the alarm to sound if the door is not closed when the device is armed. External Inhibit Input This optional input is provided to allow remote override of the Chexit in the armed condition. It also allows remote reset of the Chexit in an alarmed condition. Fire Alarm Input This input disables the Chexit immediately upon a fire alarm. Internal Auxiliary Lock The Auxiliary Lock is engaged when the Chexit is armed. The locking mechanism is specifically designed to hold securely even when the exit device is struck with forceful blows. User Definable Rearm Time The Rearm Time is the amount of time after the device is activated (via key switch or external inhibit) before it arms. It is designed to give someone time to pass through the door before rearming occurs. The user can change timing for any time between 2 and 28 seconds in two-second intervals. There is also an infinite rearm setting that requires the use of an external door position switch. In this setting the door remains in the rearm mode until the door is closed. This can be useful on jet way doors in an airport. Factory Definable Delay Most jurisdictions allow 15 seconds of delay before allowing egress. In those cases when 15 seconds is not appropriate, Von Duprin can set the Chexit for any delay time between 0 and 60 seconds in two-second increments. For delays greater than 15 seconds a letter from the local authority must be provided with the order.

Alarmed Exit Devices (cont.) To Order, Specify: 1. Prefix product description number CX. Example: CX99L 2. Door size other than 3 (914mm). 3. Door thickness other than 1 3/4 (45mm). 4. Finish. 5. Handing, LHR or RHR. Required with CD option. Cylinders Cylinders are not furnished with the Chexit device and must be specified when ordering. Uses a standard 1 1 4 (32mm) mortise cylinder for the device and the CD cylinder dogging option. OPTIONS (See Chexit catalog for all options and accessories) RCM Remote Chexit Module is designed to provide the concept of the Chexit delayed exit system for door sizes smaller than the standard Chexit device can accommodate. The Chexit module is installed in a control box and mounted in a remote location. Features and functions of the standard Chexit exit device are available on the Remote Chexit Module. SPECIFICATIONS Continuous Duty 24VDC Current In-rush 16 amperes Current Holding.3 amperes External Alarm Contact 1 ampere @ 24VDC Fire Alarm Input, External Inhibit Input, Door Position Input set-up for normally closed dry contacts. RCM Module RCM Control Box, Lens, Cover Basic Chexit single door application configuration consists of the Chexit device, power transfer and PS873 power supply. Using this setup, the Chexit will delay egress when armed and act as a normal exit device when turned off. Minimum Door Opening for CX and CX-R (RCM) 3 (914mm) 4 (1219mm) Device Length Length CX33A/35A RIM 2 10 (864mm) 3 4 (1016mm) CX 98/99 RIM 2 10 (864mm) 3 4 (1016mm) CX 98/9927 2 9 (838mm) 3 3 (1041mm) CX 98/9947 2 9 (838mm) 3 3 (1041mm) CX 98/9947-F 2 10 (864mm) 3 4 (1016mm) CX 98/9975 2 10 (864mm) 3 4 (1016mm) CX-R 33A/35A RIM 2 5 (864mm) 2 11 (1016mm) CX-R 98/99 RIM 2 5 (864mm) 2 11 (1016mm) CX-R 98/9927 2 4 (838mm) 2 10 (1041mm) CX-R 98/9947 2 4 (838mm) 2 10 (1041mm) CX-R 98/9947-F 2 5 (864mm) 2 11 (1016mm) CX-R 98/9947WDC 2 5 (864mm) 2 11 (1016mm) CX-R 98/9975 2 5 (864mm) 2 11 (1016mm) To Fire Alarm 2 x 18 ga. 2 x 12 ga. 2 x 18 ga. 120 VAC 3 x 14 ga. Junction Box EPT-10 Cable 2 x 12 ga. PS873 Power Supply Cylinder Dogging Special Center Case Cylinder dogging option is available to allow push/pull operation of the Chexit, when disarmed and used in a heavy traffic area. Prefix device with CD and specify handing. Gnd +24 PS873 Power Supply Fire Alarm +24 Red Gnd Black SC White FA Yellow DPS Orange EI Green CM+ Grey CM- Violet NO Blue C Brown Chexit Cable 21

Accessories Electrical Power Transfer Electric Power Transfer provides a means of transferring electrical power from a door frame to the edge of a swinging door. The units are completely concealed when the door is in the closed position, and are ideally suited for installations involving abuse or heavy traffic. Two models are available; EPT-2, two 18 gauge wires and EPT-10, ten 24 gauge wires. The EPT-2 and EPT-10 are UL listed as miscellaneous door accessory. Pneumatic Controls PNT-1 is available for pneumatic latch retraction exit devices. Appearance and dimensions are identical to EPT models. UL listed for use on fire doors. Door Applications Up to 5 butt hinges - 180 Swing 5 1/2 butt hinges - 130 Swing 6 butt hinges - 110 Swing 3/4 butt offset pivots - 180 Swing Not for use with swing clear hinges or center-hung pivots. SPECIFICATIONS Housing 9 x 1 1 4 x 1 5 8 (229mm x 32mm x 38mm) EPT-2 Two 18 gauge wires Up to 2 amps @ 24VDC, with a 16 amps maximum surge EPT-10 Ten 24 gauge wires, up to 1 amp @ 24VDC, with a 16 amps maximum surge PNT-1 5 32 Tubing TO ORDER, SPECIFY: 1. EPT-2, EPT-10 or PNT-1 2. Finish, SP28 or SP313 UL Listed as Miscellaneous Fire Door Accessory GVUX Junction Box High quality NEMA 1, junction boxes provide convenient installation, available in three models. These surface mounted units are 10 (254mm) high, 10" (254mm) wide and 6 (152mm) deep and includes hinged door with twist turn lock. 24 position terminal strip will accept from 24 to 12 gauge wire. Five models: JB7 Junction box only. JB7-R1 Junction box with SPDT Relay. JB7-R2 Junction box with DPDT Relay. JB7-R3 Junction box with DPDT Relay on Make Relay. JB7-R4 Junction box with DPDT Relay on Brake Relay. 29

PS914 4 amp power supply (Von Duprin) Photo as shown includes optional board(s). Please contact your local sales office or visit the support section on our website for configuration assistance. Overview Features and benefits Von Duprin s power supply and option boards were designed to meet the specific requirements of electrified fire exit devices. Installation is simplified by utilizing a flat mounting design and polarized locking connectors for option boards. This new design eliminates the need for racks and side connectors. The flat mounting of the option boards also provides for easier access to the terminal blocks for connection of electrified devices (such as electrified panic devices, strikes, card readers, etc.). Common to the line of PS900 Series power supplies is a constant output rating at both 12v and 24v settings, universal 120 VAC to 240 VAC input, and polarized option board connectors. New fire alarm interface board mounting allows outputs to be configured as switched (power cut) or unswitched (power continues) when signal is provided. * All PS900 Series power supplies and option boards have been tested and certified to meet UL 294. 4A @ 12/24 VDC output, field selectable with jumper Designed with high in rush current for powering electrified panic devices Universal 120-240 VAC input Low voltage DC, regulated and filtered Electronic power limiting foldback circuit for AC current overload protection Two polarized connectors for distribution boards Fused primary input AC status monitor - isolated SPDT contacts AC input and DC output LED status indicators Cover mounted AC input indication Hinged cover with lock down screws High voltage protective cover