1
0.018.8843(4)h90 Specification Door width : Up to 1100mm (refer to selection chart) Door Weight : Up to 115kg as standard Door thickness : Minimum for timber 32mm Door control : Two independent adjustment valves provide full hydraulic control from 130 to 15 of closing and 15 to 0 of latching. Door frame type : Timber/ aluminium/ steel Non hold open & hold open versions : Available in both non hold open & hold open versions. Mechanical hold open 90. Door adjustment : Adjustable for height of 4mm, a width of 10mm, a length of 9mm Cover plate finish : Stainless steel (SSS), Gold (GLD), Polished stainless Steel (PSS) Other finished on application Size Selection Chart Power Size Door Width Max Door Weight Closing Torque 3 950mm 115kgs 2Nm 4 1100mm 115kgs 39Nm Limiting Dimensions www.sehanluce.co.kr 32 40 130 108 24 20 54 306 324 Bottom Strap 10 SP884-10 5 25 Top Pivot 165 Top Pivot Housing 122 SP884-20(kit) 11 29 15 C C B B 90 A 105 130 A 90 & 105 HOLD B CLOSING RANGE C LATCHING RANGE 2
0.018.8843(4)H90 24 10 FLOOR HINGE 108 20 23 40 90 Hold Open 843H90SSS Size 3 standard floor spring 90 hold open 8844H90SSS Size 4 standard floor spring 90 hold open A Standard Extended Spindle Range Part number Standard Insert +5mm +10mm +15mm +20mm +25mm +30mm SP884-60 SP884-60-5 SP884-60-10 SP884-60-15 SP884-60-20 SP884-60-25 SP884-60-30 3 Left Hand Offset SP884-60LH SP884-60-5LH SP884-60-10LH SP884-60-15LH SP884-60-20LH SP884-60-25LH SP884-60-30LH 3 Right Hand Offset SP884-60RH SP884-60-5RH SP884-60-10RH SP884-60-15RH SP884-60-20RH SP884-60-25RH SP884-60-30RH More to expect from our hardware than just design and technology. 3
0.018.55H90 Limiting Dimensions 5-62 Adjustments within Cement Box - Vertical 9mm - Side 6mm - Front 5mm 5 8 82 55 241 345 103-42 - 42 Power and Closing Speed Turn 1 mm hex force adjuster clockwise to increase power. Turn anticlockwise to decrease power. Starting from the minimum power, with 10 complete turns maximum power is reached. Thermostatic valves 1 and 2 control independently the general closing speed from 15 to 15 and the final closing from 15 to 0 (constant, damping or latching). Starting from valve closed, maximum speed is reached with three full turns anti-clockwise. 15 0 15 ~15 Recommended Door Size Min. power 3 =24Nm Min. 850 x 2300 kg.300 Max. power 6 =60Nm Max. 1400 x 2500 kg.300 Universal Mounting LEFT HAND DOUBLE ACTION RIGHT HAND Extended Spindle Range www.sehanluce.co.kr 0 5 10 15 20 25 30 SP0-60 SP0-60-5 SP0-60-10 SP0-60-15 SP0-60-20 SP0-60-25 SP0-60-30 4
0.018.55H90 Features & Specification Power adjustable All models are power adjustable size 3 to 6 which allows adjustment at installation to suit most site conditions. Closing force ranges from 24Nm to 69Nm. Suitable for doors Up to 1400mm in width(refer to selection chart), up to 2500mm in height minimum door thickness 40mm Door weight : Up to 300kg Door controls (15 in both directions) Two independent adjustment valves provide full hydraulic control. Closing from approx. 15 to 15. Latching from approx. 15 to 0 Hold open: 90 and 105 Non hold open(fire rated) Comes with mechanical backcheck at approx 0 Floor spring has successfully been fire tested up to 4hours on fire door assemblies in accordance with Australian Standard AS 1905.1~2005: Fire resistant doorsets Built in pressure relief valve: To protect against abuse Adjustment within cement box Large range of adjustment(see limiting dimensions below) to suit most site conditions Cast iron body Cement box: hot zinc plated steel Interchageable spindle A large range of spindle are available from + 5mm to 30mm to meet door heights above thresholds or uneven floor conditions Cover plate finishes Satin Stainless steel (standard) -SSS Polished stainless steel (Order cover plate separately) - PSS Polished brass (Order cover plate separately) -PB A Standard Extended Spindle Range Part number Standard Insert +5mm +10mm +15mm +20mm +25mm +30mm SP884-60 SP884-60-5 SP884-60-10 SP884-60-15 SP884-60-20 SP884-60-25 SP884-60-30 3 Left Hand Offset SP884-60LH SP884-60-5LH SP884-60-10LH SP884-60-15LH SP884-60-20LH SP884-60-25LH SP884-60-30LH 3 Right Hand Offset SP884-60RH SP884-60-5RH SP884-60-10RH SP884-60-15RH SP884-60-20RH SP884-60-25RH SP884-60-30RH More to expect from our hardware than just design and technology. 5
0.018.9854h90 The closer fits into the transom above the door, most of the preparatory work is undertaken prior to installation, leaving minimal on-site fitting. Fully concealed door closers are designed to provide positive centering and door control on manually operated single or double action internal and external doors in schools, hospitals, clubs, factories, offices and commercial buildings. Features The closer fits into commercial buildings. Suitable for fire, metal, timber and glass doors. Minimum door thickness 38 mm. Suitable for both single and double action doors. Suitable for both single and double action doors. Adjustable closing and latching speeds. (Closing from 130 to 15, latching from 15 to 0.) All models feature easy to install side load design. Maximum door opening angle of 130. Mechanical hold-open at 90 &105. Built in back check from approximately 80. Fully adjustable, vertically within opening & central parking positions. 0mm pivot point. Specifications High grade cast iron body. Internal mechanism components utilising heat treated high alloy steels and ball bearings for optimum efficiency. Stable hydraulic oil for a wide range of climatic conditions enabling constant operation. Built in pressure release valve protects closer from rough use. Compact body size fits into 44.5 mm x 100 mm header section. Door Pivot Sets Suitable for door applications when a free swing pivot door is required. Consists of retractable top pivot set with heavy duty bottom pivot and strap. Suitable for Aluminium, Timber and Glass Doors. Successfully tested on fire door assemblies in accordance with Australian Standard AS 1905 Part 1, 199 Fire Resistant Doorsets. Size Selection Chart www.sehanluce.co.kr POWER SIZE DOOR WIDTH MAX DOOR WEIGHT CLOSING TORQUE 4 1220mm 115kgs 29Nm 6
0.018.9854h90 Size 4 overhead transom closer 90 hold open Limiting Dimensions Heavy Duty Bottom Pivot 200kg Fire Rated Heavy Duty 38 56 24 93.5 92 298 38 25 25 80 C C B 80 90 105 A A 130 24 20 3 20 - x 10 Bottom Strap 10 10 Floor Pivot Bearing 44 100 63 205 12 14 12 B A BACK CHECK BCLOSING RANGE CLATCHING RANGE Aluminium/Timber/Glass Doors Arange of OTC Designed specifically to meet the needs of Aluminium/Timber door requirements. Exploded View Fire Box Cover Plate Aluminium/ Timber Door Adjustable Pivot Heavy Door Bottom Pivot & Strap Fire Rated SP884-10 SP985-35 (200kg) More to expect from our hardware than just design and technology.
0.018.SP985 OFFSET HUNG TYPE CENTER HUNG TYPE Bottom Strap Floor Pivot Bearing 24 44 10 3 20- x 10 20 10 100 Heavy Duty Bottom Pivot - 200kg www.sehanluce.co.kr 8
SPARE PARTS 0 5 10 15 20 25 30 SP0-60 SP0-60 -5 SP0-60 -10 SP0-60 -15 SP0-60 -20 SP0-60 -25 SP0-60 -30 40 Ø14 25 20 10 22 90 10 6 6 21 24 35 2 54 54 153 62 10 2 132 40 Ø14 2 25 40 6 6 15 10 3 15 85 85 10 22 90 10 35 2 249 2 132 200 200 18 10 20.5 6.5 20.5 6.5 50 46 46 46 50 46 46 46 20 20 33 33 3 56 56 More to expect from our hardware than just design and technology. 9
0.012.5004 Features: Tested to EN 1154, CN QB/T 269-2005-A class certified: For door width and weight maximum of 1.2m and 130kg respectively Tested to 500,000 cycles: 3years warranty Dual action floor spring with 3 installation adjustment to meet the needs of new and retrofit applications Closing and latching speed adjustments control the door during operation Suitable for -25 C to 40 C Cast iron body with stainless steel cover Size requirements for floor spring and timber/ aluminium door accessory 24 10 108 18 40.5 MAX5 = A (MAX 12 = B) (MAX 20 = C).5 42.5 150 M5x8.5 M5x25 150 30 46 46 8 8 VIEW X-X M6x25 32 Z 32.5 24 40 40 Z Y X X 165 Y 150 (20) (20).5.5 52-55 VIEW Z-Z 8.5 COVER PLATE 1mm 12 VIEW Y-Y 35 www.sehanluce.co.kr 305 10
0.012.5004 Patch Fitting Features: Cast aluminium body with steel spindle housing provides stability and longer life cycle Durable stainless steel cover Suitable for 10mm-12mm door thickness Patch lock with ingersoll rand : commercial E series lock cylinder can be easily integrated into a master keying system PF40 PF10 PF20 PL10 Size of glass door patch fittings PF30 PF20 PF40 PF20 166 52 3 218 166 PF10 PF10 PF10 PF10 FLOOR SPRING FLOOR SPRING Size requirements for glass door 34 62 8 126 R8 35 Ø20 132 146 186 34 5 PF10/PF20/PF30 PF40 PL10 A. PF10, PF,20, PF30 B. PF40 C. PL10 52 R92 96 Ø15 102 64 4 Ø20 52 106 25 42 25 52 15 130 15 More to expect from our hardware than just design and technology. 11
Door Closer Selection Guide Door Closer Selection Guide Selection of door closer size is judged in two ways. 1.Does the door closer have the strength to effectively close the door against unexpected air pressures? 2.Is the door closer oversize for the application and therefore affecting the ease of operation? Efficiency of the door closer also has a major bearing on ease of operation. For optimum performance it is essential that a highly efficient door closer of a correct size is selected. The use of spring strength adjustability, which allows fine tuning of strength on site, has simplified this task but not removed all of the guesswork. With more architects and engineers becoming conscious of the problems caused by incorrect selection of door closer strength, it has become the responsibility of manufacturers to provide better technical information, such as closing torque and efficiency of their products. The following charts have been produced to cover most conditions. If you have an unusual application which you feel requires special consideration, please forward all relevant information to your local of fice and we will be happy to advise the best door control for your application. Fire doors and pressurised stairwells pose significant challenges in ensuring closing and latching of fire doors. The problems are created by differential air pressures resulting from airconditioning systems, either on one or the other side of the door. To achieve complete fire safety, fire doors must latch securely at all times. If this performance is not achieved, the stairwell may be unsafe, and in the event of fire, loss of life and property may occur. Correct selection of door hardware is of paramount importance in ensuring that the appropriate operating standards are met. Fire doors which open into a pressurised stairwell must meet the following criteria: the door must close against a pressure differential between the airconditioned floor area and non-airconditioned stairwell; -the door must latch securely every time it closes; -the door must be able to be opened with a force not exceeding 110N when the stairwell is pressurised; and the door must be protected from damage when it is opened by means of a backcheck action which is built into the door closer Note Always round up to the next door width (ie for 80 mm door use 950 mm). If parallel arm installation, then use next door width door line (ie, for 830 mm door use 950 mm). For internal doors deduct 200 mm from actual door width (ie for 1250 mm internal door use 1050 line). This chart is based on normal climatic conditions (ie pressure differential of 30Pa or wind of 15 knots). If more severe conditions are expected then use the next door width or consult the office in your location (refer back page). When specifying parallel arm and slide rail functions, allowance should be made for the following power loss: Parallel Arm Mounting Approximately 20 per cent loss Slide Rail Mounting Approximately 30 per cent loss Power Selection Chart Power Selection Chart This chart will be most useful in selecting the correct door closer. Simply identify the dimensions of the appropriate door and select the recommended door closer. The chart is intended as a guide only and as such the following variations should be taken into account when making your selection: Environmental factors such as the effect of wind or airconditioning pressures. An unsheltered external door is a door on which prevailing wind gusts will directly produce a sail area affect. A sheltered external door is a door way which is protected by a wind break or wall, which acts as a barrier against direct wind gusts. Note: Movement curve represents approximate forces r equired to operate a size 3 door closer. Note: The illustration is an approximation based on one set of parameters. Any change to these parameters will result in a variation of performance. Closer Selection Chart Door Width 50 850 950 1100 1250 1400 Maximum Door Weight 20kg 40kg 60kg 80kg 100kg 120kg Closer Size 1 2 3 4 5 6 Closing Torque min max 9Nm 13 Nm 13 Nm 18 Nm 18 Nm 26 Nm 26 Nm 3 Nm 3 Nm 54 Nm 54 Nm 8 Nm Movement Curve Slide arm pull side NM 40 30 Parallel arm push side www.sehanluce.co.kr 20 10 120 90 60 30 0 30 60 90 120 Slide arm pull side Parallel arm push side 12
0.018.14 Maximum Width 1,800m/m, Maximum Weight 80kg A range of adjustable power door closer units suitable for architectural and commercial applications. Approved on fire door assemblies up to 4HR, in accordance with Australian Standards AS1905 Part 1 Fire Resistant Doors 1984. Standard Features Stainless steel cover 2-6 power adjustable Delayed action Adjustable backcheck Speed controls Overload protection. Non-handed Regular, parallel & over door mounting Hold Open Hold open can be set at any angle up to 150º of opening Standard Finishes Satin Stainless Steel Polished Stainless Steel Bright Gold lsss lpss GLD 14 Standard Arm Closer installed on pull side of door. This mounting position permits opening of 180. Part Numbers : Non hold open 14 Hold open 14 32 264 83 309 30 55 14 Parallel Arm Closer installed on push side of door. This mounting position permits opening of 180. Part Numbers : Non hold open 14 Hold open 14H 449 61 124 81 3 0 14 Over Door Mounting Closer installed on push side of door and top rail where conditions do not allow parallel mounting. This mounting position permits opening of 180. Part Numbers : Non hold open 14 Hold open 14H 0 29 22 55 264 40 More to expect from our hardware than just design and technology. 13
0.018.14SR Maximum Width 950m/m, Maximum Weight 60kg The Slide Arm Series permits smoother opening by way of reducing power as the door opens. Ideally suited for schools, hospitals or doors where children, disabled or the aged may enter. Standard Features Stainless steel cover. 1-3 Power adjustable. Delayed action. Adjustable hold open (Inclusive). Adjustable backcheck. Speed controls. Overload protection. Non-handed. Regular & over door mounting. Standard Finishes Satin Stainless Steel SSS Polished Stainless Steel PSS Bright Gold GLD Approved on fire door assemblies up to 4HR, in accordance with Australian Standards AS1905 Part 1 Fire Resistant Doors 1984. Hold Open Hold open angle is the same as opening angle. 14 SIDE ARM PULL SIDE Closer installed on pull side of door. This mounting position permits opening of 15. Part Numbers : 14SR 546 49 41 81 0 66 55 14 SIDE ARM PUSH SIDE Closer installed on push side of door. This mounting position permits opening of of 130. Part Numbers : 14SR 546 49 126 0 25 55 14 SLIDE ARM OVER DOOR MOUNTING Closer installed on push side of door and top rail where conditions do not allow parallel mounting. This mounting position permits opening of 130. Part Numbers : 14SR 0 4 50 www.sehanluce.co.kr 8 4 546 4 14
0.018.24 Maximum Width 1,100m/m, Maximum Weight 80kg A range of adjustable power door closer units suitable for architectural and commercial applications. *Other finishes available on request. Approved on fire door assemblies up to 4HR, in accordance with Australian Standards AS1905 Part 1 Fire Resistant Doors 1984. Standard Features 2-4Power adjustable Hold open Adjustable backcheck. Speed controls Overload protection Non-handed. Regular, parallel & over door mounting Short arm - to suit 400 mm width door SP24-130SIL Hold Open Hold open can be set at any angle up to 150º of opening. Standard Finishes Silver SIL Gold GLD Brown BRN Black BLK 24 Standard Arm Closer installed on pull side of door. This mounting position permits opening of 180. Part Numbers : Non hold open 24 Hold open 24H 264 32 69 40 235 91 24 Parallel Arm Closer installed on push side of door. This mounting position permits opening of 180. Part Numbers : Non hold open 24 Hold open 24H 449 61 109 24 Over-Door Mounting Closer installed on push side of door and top rail where conditions do not allow parallel mounting. This mounting position permits opening of 180. Part Numbers : Non hold open 24 Hold open 24H 6 3 235 235 91 35 40 264 40 More to expect from our hardware than just design and technology. 15
0.018.24SR Maximum Width 950m/m, Maximum Weight 60kg The Slide Arm Series permits smoother opening by way of reducing power as the door opens. Ideally suited for schools, hospitals or doors where children, disabled or the aged may enter. Standard Features 2-3 power adjustable Adjustable hold open (Inclusive) Adjustable backcheck Speed controls Overload protection. non-handed Regular & over door mounting Standard Finishes SIlver SIL Brown BRN Gold GLD Black BLK Approved on fire door assemblies up to 4HR, in accordance with Australian Standards AS1905 Part1 Fire Resistant Doors 1984. Hold Open Hold open angle is the same as opening angle. 24 Slide Arm Pull Side Closer installed on pull side of door. This mounting position permits opening of 15. Part Numbers : 24SR 41 546 49 81 235 128 40 24 Slide Arm Push Side Closer installed on push side of door. This mounting position permits opening of 130. Part Numbers : 24SR 546 49 126 235 38 40 24 Slide Arm Over Door Mounting Closer installed on push side of door and top rail where conditions do not allow parallel mounting. This mounting position permits opening of 130. Part Numbers : 24SR 235 109 50 64 www.sehanluce.co.kr 4 546 4 16
0.018.26 Maximum Width 1,400m/m, Maximum Weight 120kg A range of adjustable power door closer units suitable for architectural and commercial applications. Standard Features Stainless steel cover 2-6 Power adjustable Delayed action Adjustable backcheck Speed controls Overload protection Non-handed Regular, parallel & over door mounting Standard Finishes Satin Stainless Steel SSS Polished Stainless Steel PSS Bright Gold GLD Approved on fire door assemblies up to 4HR, in accordance with Australian Standards AS1905 Part 1 Fire Resistant Doors 1984. Hold Open Hold open can be set at any angle up to 150º of opening. 26 Standard Arm Closer installed on pull side of door. This mounting position permits opening of 180. Part Numbers : Non hold open 26 Hold open 26H 32 282 81 0 91 55 26 Parallel Arm Closer installed on push side of door. This mounting position permits opening of 180. Part Numbers : Non hold open 26 Hold open 26H 480 61 123 26 Over Door Mounting Closer installed on push side of door and top rail where conditions do not allow parallel mounting. This mounting position permits opening of 180. Part Numbers : Non hold open 26 Hold open 26H 81 35 0 0 91 19 55 282 40 More to expect from our hardware than just design and technology. 1
0.018.26SR Maximum Width 1,250m/m, Maximum Weight100kg The Slide Arm Series permits smoother opening by way of reducing power as the door opens. Ideally suited for schools, hospitals or doors where children, disabled or the aged may enter. Standard Features Stainless steel cover 2 5 power adjustable Delayed action Adjustable hold open (Inclusive) Adjustable backcheck Speed controls Overload protection Non-handed Regular & over door mounting Standard Finishes Satin Stainless Steel SSS Polished Stainless Stee lpss Bright Gold GLD Approved on fire door assemblies up to 4HR, in accordance with Australian Standards AS1905 Part 1 Fire Resistant Doors 1984. Hold open Hold open angle is the same as opening angle. 26 Slide Arm Pull Side Closer installed on pull side of door. This mounting position permits opening of 15. Part Numbers : 26SR 546 54 126 0 106 55 26 Slide Arm Push Side Closer installed on push side of door. This mounting position permits opening of 130. Part Numbers : 26SR 546 89 124 0 19 55 26 Slide Arm Over Door Mounting Closer installed on push side of door and top rail where conditions do not allow parallel mounting. This mounting position permi ts opening of 130. Part Numbers : 26SR 0 86 50 9 www.sehanluce.co.kr 45 18
0.012.1110 Briton 1110 & 1120B with and without optional covers Finish options Basic Trimplate versions for 1110 Silver sprayed with matching armset (.SES) Gold sprayed with matching armset (.GES) Silver sprayed with black armset (.SE) Optional all-over cover note: additional covers can be used with any trimplate closer combination PS - Polished Stainless Steel SS - Satin Stainless Steel PA - Polished Aluminium SA - Satin Aluminium PB - Polished Brass Trimplate and Cover options The all-over cover option can be applied directly to the trimplate versions providing a means of combining different arm and cover finishes (see table opposite). Product Feature Product References max. door size closer size width - weight 1 850mm - 40kg 2 950mm - 60kg 3 1100mm - 80kg Main Features CE Marked Body size Method of adjustment Angle of opening Separate latch action/closing speed Manual hold open option Matching arm finish Tri-pack for Fig.1, Fig.61 & Fig.66 Non handed, for LH or RH applications Trimplate All over cover option 1110 1110 small template 180 More to expect from our hardware than just design and technology. 19
0.012.1110 Cover style Dimensions (mm) All-over cover Trimplate 1110. length (L) 245 20 width (W) 2 60 depth (D) 50 38.5 W EN classifications range shown in brackets (3/4) (8) (1-) (0/1) (1) (0/4) 1110 3 8 2-4 1 1 3 Designed to and fully compliant with EN 1154 and best practice codes for performance, reliability and safety (see page 16 for more information) D L Designed to and fully compliant with EN 1154 and best practice codes for performance, reliability and safety (see page 16 for more information) CF388 Snap joint arm for quick and easy installation and future maintenance Optional hold open armset allows the door to be held in the open position for convenience ( not to be used on fire door applications) Arm set manufactured from forged steel for additional strength and durability Supplied with Tri-pack armset suitable for Fig.1, Fig.61, and Fig.66 applications Trimplate design conceals fixing and adjustment screws reducing the risk of vandalism High quality silicon chrome alloy steel used for the coil spring High quality hydraulic fluid for optimum performance and long life with temperature compensation from -15 C to + 40 C Precision needle roller bearings allied with rack and pinion mechanism provides efficient operation and high levels of durability Covered version has an all-over cover to conceal all fixings and adjustment screws providing a neat appearance and reducing the risk of tampering and vandalism www.sehanluce.co.kr Separate latch action and closing speed adjustment provides total accuracy of adjustment of the full closing cycle. Adjustable backcheck (1120B) minimises the risk of damage to the door, its hardware and the surrounding structure 20
0.012.C2003 Features C2000 series is a newly designed concealed door closer suitable for all types of luxury doors and frames. The C2000 s slim closer body, 30.5mm in thickness, provides complete concealment. Reversible valve system is suitable for right or left handing. Precise adjustable valve function(closing and latching speed control) provides smooth, quiet door control. Slide arm set is designed to allow easy adjustment of hold open points. 3years warranty, 500,000 life cycle. Hold - open force adjusting nut Hold - open siding block (New hold - open device) Hold - open hook Model No. C2003 For door width(max mm) 950 For door weight (Max kgs) 65 For door thickness ( min mm) 40 Hold open Optional Back check Optional Finish SE-SILVER, GE-GOLDEN, BE-BROWN 158 530 155.5 163.5 1 18 22.5 2 22.5 255 400 19 260 4.5 4.5 164 164 164 19 29 19 61 0 12 3.0 More to expect from our hardware than just design and technology. 21
0.018.1000 Featuring a non handed cast aluminium body which is non handed and is designed to meet E1154 performance. Standard Features Size EN2 & 3 fixed power strength Door weight 1020 : 40kg 1030 : 60kg Adjustable backcheck Speed controls Non-handed Concealed mounting Standards Complied with CE standard EN 1634 Fire Test : 90mins EN 1154 performance standard. Tested to 500,000 operation cycles. Standard Finishes Silver - SB Gold - GB Standard Concealed Operation Closer installed inside of door. This mounting position permits opening of 120. Body Dimension Length : 230mm Height : 6.8mm Width : 32mm Maximum Door Width 1020 : 850mm 1030 : 950mm Technical Data - Limiting Dimensions Applications - Mounting Details 29 6.8mm 19 Sliding Arm installation closer is concealed into the door. 81 230mm 32mm 33 Metal Door 35mm Wooden Door 40mm How to order 33 Metal Door 35mm Wooden Door 40mm www.sehanluce.co.kr Ordering No. Product Description Max. Door Weight Range 1020 Concealed Door Closer size 2 40kg 1030 Concealed Door Closer size 3 60kg 19 29 81 Sliding Arm installation closer is concealed into the door frame. 22
0.011.8202 Control valve of brake. Top 8.5 5.5 120 25 8.5 2 2 108 101 95 R6 R6 R6 Thickness 10~12mm Maximum width 1,200mm Maximum Weight 150kg 16.5 35 113 10-12 32 91 98 0.011.8201 Oildynamic hinge with adjustment of the closing speed of the door. Stop at 0 +90-90 Bottom 23 35.5 10-12 98 91 40 2 32 R13 R6 Thickness 10~12mm Maximum width 1,200mm Maximum Weight 150kg 155 120.5 10 2 8.5 108 148 50 3.5 134 128 R6 More to expect from our hardware than just design and technology. 23
0.011.8010 Oildynamic hinge with adjustment of the closing speed of the door. Stop at 0, +90, -90. 55 50 14.5 40.5 10-12 29.5 5 8 84 108 80 6.5 40 9.5 R5 R11 Thickness : 10~12mm Maximum Width : 1,000mm Maximum Weight : 100kg 0.011.8011 50 29.5 80 0.011.8015 50 29.5 14 14 Oildynamic hinge(with offset fixing wing) with adjustment of the closing speed of the door. Stop at 0, +90, -90. 14.5 10-12 108 10-12 84 8 84 108 5 6.5 40 14 9.5 R5 R11 52 Thickness : 10~12mm Maximum Width : 1,000mm Maximum Weight : 100kg Oildynamic hinge(glass to glass 180 ) with adjustment of the closing speed of the door. Stop at 0, +90, -90. 40 84 8 6.5 www.sehanluce.co.kr Thickness : 10~12mm Maximum Width : 1,000mm Maximum Weight : 80kg 3 3 R11 R5 24
Patch Fitting Range 0.018.LWP010 Bottom door patch to suit 8800 floor springs. 164 32 0.018.LWP020 Top door patch to suit 15mm pivot. 164 32 0.018.LWP022 Top patch to suit 9800 transom closer(side load). 164 32 More to expect from our hardware than just design and technology. 25
Patch Fitting Range 0.018.LWP030 Top patch with 15 mm pivot. 164 0.018.LWP040 Top patch for over and side panel with 15 mm pivot. 218 32 106 0.018.LWP041L/R Patch for over panels, side panel with fin fitting (Handed left or right). www.sehanluce.co.kr 111 55/65 218 Ø15 26
Patch Fitting Range 0.018.LWP060/61 Over panel and side panel for double or single swing doors with or without stops. 106 32 106 53 53 0.018.LWP062 Connector for over panel and side panel with stop. 32 53 2 106 53 106 0.018.LWP00 Over panel connector with stop inserts. 30 116 26 23 29 29 15 More to expect from our hardware than just design and technology. 2
Patch Fitting Range 0.018.LWl010 Corner lock suits Europrofile cylinder. Bolt has 20mm projection. C4 Keying. 164 164 164 0.018.LWl020 Centre lock suits Europrofile cylinder. Bolt has 20mm projection. C4 keying. 164 164 52 52 52 52 52 0.018.LWs020 Double over panel strike box. Suits LWL/010 corner locks. 164 164 164 164 164 www.sehanluce.co.kr 32 32 32 32 32 332 332 332 332 332 28
Patch Fitting Range 0.018.LWs030 Single over panel strike box. Suits LWL/010. 164 32 0.018.LWs040 Corner over panel strike box. 218 105 52 0.018.LWs050 Universal strike box. 164 More to expect from our hardware than just design and technology. 29
TYPICAL INSTALLATION DETAILS LWP/ 030 COVER Gum Paper (Install cover after removing protective paper) LWP/ 040 COVER Gum Paper (Install cover after removing protective paper) LWP/ 020 COVER Gum Paper (Install cover after removing protective paper) LWL/ 020 LWP/ 010 LWL/ 010 COVER Gum Paper (Install cover after removing protective paper) www.sehanluce.co.kr COVER Gum Paper (Install cover after removing protective paper) 30
Glass Cutout Details LWP/010/020/022/030 and LWS/030 Top, bottom and over panel patch cutout. Note: Not to scale. R55 R80 3 Ø20 68 146 161 LWP/040 Over panel and side panel with 15mm pivot glass cutout. Note: Not to scale. Ø20 68 1 Ø20 R55 R80 3 161 146 3 Ø20 LWP/060/061/062 Connector for over panel with inserts glass cutout. Note: Not to scale. 3-Ø20 1 3 More to expect from our hardware than just design and technology.
Glass Cutout Details LWP/041L/R Corner patch with reinforcing fin right/left hand glass cutout. Note: Not to scale. 161 1 146 3-Ø20 68 A R55 R80 3 B 3 LWP/00 Over panel connector. Note: Not to scale. 1 3 2-Ø20 30 LWL/010 Corner lock glass cutout. Note: Not to scale. R10 43 www.sehanluce.co.kr 148 32
A Glass Cutout Details LWS/020 Double over panel strike box glass cutout. Note: Not to scale. 161 1 161 146 146 68 68 R55 R80 3 R80 R55 LWS/040 Corner over panel glass cutout. Note: Not to scale. 1 146 161 68 3-Ø20 3 R80 R55 3 B LWS/050 and L WL/020 Strike box and centre lock glass cutout. Note: Not to scale. 133 2-R10 45 More to expect from our hardware than just design and technology. 33
MEMO www.sehanluce.co.kr 34