M323F Railroad Wheeled Excavator Technical Specifications Engine Engine Model Ratings Cat C4.4 ACERT 2,000 rpm Rated Net Power (ISO 24/SAE J134) 112 kw/152 PS Maximum Net Power (ISO 24/SAE J134) 112 kw/152 PS Maximum Gross Power (ISO 1436) 117 kw/15 PS Bore 105 mm Stroke 127 mm Displacement 4.4 L Maximum Torque at 1,400 rpm 710 N m Number of Cylinders In Line 4 Meets EU Stage IV emission standards. Rated speed 2,000 rpm. Net power advertised is the power available at the flywheel when engine is equipped with air cleaner, Cat Clean Emission Module (CEM) exhaust gas aftertreatment, alternator, and cooling fan running at intermediate speed. No deratings required up to 3000 m altitude. Automatic derating occurs after 3000 m. Swing Mechanism Maximum Swing Speed Maximum Swing Torque Weights rpm 42 kn m Operating Weights* 22 00 kg 23 00 kg Stick 2100 mm 705 kg Counterweights Standard 6400 kg Optional 7400 kg * Operating weight includes short stick, full fuel tank, operator, no quick coupler, no bucket and dual pneumatic tires. Weight varies based on configuration. Tires Standard 10.00-20 (Dual Pneumatic) Drive Maximum Gradeability (22 00 kg) 52.5% Maximum Travel Speed Road Mode 20 km/h Maximum Travel Speed Rail Mode 20 km/h Drawbar Pull Road Mode 104 kn Drawbar Pull Rail Mode 45 kn Hydraulic System Tank Capacity System Maximum Pressure Implement Circuit Normal Heavy Lift Travel Circuit Maximum Pressure Auxiliary Circuit High Pressure Medium Pressure Swing Mechanism Maximum Flow Implement/Travel Circuit Auxiliary Circuit High Pressure Medium Pressure Swing Mechanism 122 L 240 L 35 000 kpa 37 500 kpa 35 000 kpa 35 000 kpa 18 500 kpa 37 000 kpa 240 L/min 240 L/min 4 L/min 80 L/min
Service Refill Capacities Fuel Tank Capacity 240 L Cooling System 30 L Engine Crankcase 8 L Rear Axle Housing (differential) 11.2 L Front Steering Axle (differential) L Final Drive 2.4 L Powershift Transmission 2.5 L DEF Tank 1 L Standards Cab/ROPS ISO 12117-2:2008 Rail Power Train Rail Wheel (UIC profile) Ø632 mm Track Width 1435 mm Park Brake (integrated in motor) Multi-disc Tire Ground Clearance on Rail 15 mm Undercarriage Road Ground Clearance Rail Ground Clearance Maximum Steering Angle Oscillation Axle Angle Minimum Turning Radius: Outside of Tire End of Variable Adjustable Boom Sound Performance 360 mm 15 mm 35 ±8.5 6300 mm 7100 mm Operator Sound 2000/14/EC, ISO 636:2008 77 db(a) Spectator Sound 2000/14/EC, ISO 635:2008 db(a) The operator sound level is measured according to the procedures specified in 2000/14/EC and ISO 636:2008, for a cab offered by Caterpillar, when properly installed, maintained, and tested with the door and windows closed. The external sound level is measured according to the test procedures and conditions specified in 2000/14/EC as amended by 2005/88/EC. Hearing protection may be needed when operating with an open operator station and cab (when not properly maintained or doors/ windows open) for extended periods or in a noisy environment. Emissions and Safety Engine Emissions Fluids (optional) Hydraulic Oil CAT BIO HYDRAULIC OIL Stage IV Biodiesel up to B20 Diesel Exhaust Fluid Must meet ISO 22241 Vibration Levels Maximum Hand/Arm (ISO 534-2001) <2.5 m/s² Maximum Whole Body (ISO/TR 2538:2006) <0.5 m/s² Seat Transmissibility Factor (ISO 706:2000-spectral class EM5) <0.7 m/s² Readily biodegradeable EU Flower eco-label certified. Meets EN 14214 or ASTM D6751 with EN50 or ASTM D75. Standard mineral diesel fuels 2
M323F Railroad Wheeled Excavator Specifications Dimensions All dimensions are approximate and may vary depending on bucket selection. 320 477 4680 440 80 3240 Boom Option Stick Option Top of Cab Height: Road Mode Rail Mode Shipping Height: With Boom/Stick Installed Shipping Length: With Boom/Stick Installed Variable Adjustable 2.1 m 3215 mm 3440 mm 332 mm Boom Option Stick Option Upper Frame Width without Walkways Tail Swing Radius Counterweight Clearance: Road Mode Rail Mode Bucket Capacity Variable Adjustable 2.1 m 2533 mm 1566 mm 1306 mm 1501 mm 0.35 m3 0.1 m3 677 mm 3
M323F Railroad Wheeled Excavator Specifications Work Mode Dimensions All dimensions are approximate and may vary depending on bucket selection. Work Mode Parallel to Track 1 Swing Center to Stick Pin 2 Overall Height 3 Stick Pin Center to Rail 1 Swing Center to Stick Pin 2 Overall Height 3 Stick Pin Center to Rail Overhead Line Clearance of 320 mm 7628 mm 320 mm 278 mm Overhead Line Clearance of 4280 mm 7514 mm 4280 mm 3503 mm Work Mode Perpendicular to Track 4 Overall Height 5 Stick Pin Center to Rail 6 Swing Center to Stick Pin 4 Overall Height 5 Stick Pin Center to Rail 6 Swing Center to Stick Pin Overhead Line Clearance of 320 mm 320 mm 1163 mm 553 mm Overhead Line Clearance of 4280 mm 4280 mm 1521 mm 5261 mm Work Mode On Rails Traveling Position 320 mm 7 Overall Height 8 Stick Pin Center to Rail Swing Center to Stick Pin 1100 mm 5200 mm 7 8 4
Working Ranges 7.5 7.5 6 6 4.5 4.5 3 3 1.5 1.5 0 m 0 m 1.5 1.5 3 3 4.5 4.5 0 m 1.5 3 4.5 6 7.5 0 m 1.5 3 4.5 6 7.5 Boom Type Stick Length Digging Height Dump Height Digging Depth Vertical Wall Digging Depth Depth 2.5 m in Straight Clean-Up Reach Reach at Ground Level Bucket Digging Force (ISO 6015) Stick Digging Force (ISO 6015) Variable Adjustable 2100 mm 10 070 mm 620 mm 5610 mm 4380 mm 5500 mm 110 mm 00 mm 114 kn Range values are calculated with GD bucket 1100 mm, 0.80 m3 with tips K080 and CW-20-H.4.N quick coupler with a tip radius of 1574 mm. Breakout force values are calculated with heavy lift on (no quick coupler) and a cutting edge tip radius of 1237 mm. 84 kn 5
Lift Capacities Variable Adjustable Boom Counterweight: 6.4 t Road Mode All values are in kg. Load at maximum reach (stick nose/bucket pin) Load over front Load over rear Load over side Load point height Stick 2100 mm 7500 mm 6000 mm 4500 mm 3000 mm 1500 mm 0 mm 1500 mm 3000 mm 3000 mm 4500 mm 6000 mm 7500 mm TOOL POINT *5350 *5350 *400 *5000 *5000 4050 503 ALP *550 *550 4850 *6050 *6050 5100 4348 TOOL POINT *5250 *5250 *4800 *4500 *4500 3250 *4350 *4350 2800 6443 ALP *5400 *5400 *4700 *5050 4300 3050 *5050 *5050 3150 58 TOOL POINT *8650 *8650 *7750 *500 *500 *4650 *4400 4400 3250 *4100 3250 2300 7213 ALP 8000 8000 *7600 *6000 *6000 *4600 *4550 4300 3100 *4750 3550 2500 6736 TOOL POINT *8750 *8750 *7400 *6600 6300 *4550 *4850 4250 3250 *4150 250 2050 753 ALP *7000 6150 *4500 *450 4200 3100 *4550 3150 2250 7144 TOOL POINT *10 150 *10 150 *7350 *7700 5800 *4500 *5200 4100 3150 *4300 3000 2050 *4200 2850 2000 7648 ALP *600 6150 *5100 *5250 4100 3000 *4400 3050 2150 7202 TOOL POINT *12 200 11 350 700 *7750 500 4550 *5600 4000 250 *300 250 2050 7383 ALP *7650 6050 4500 *5600 4000 2850 *4200 3200 2250 61 TOOL POINT *12 50 11 350 7750 *750 6100 4400 *5350 4000 2800 3350 2350 675 ALP *7800 6000 4250 *4450 300 2700 3700 2550 6256 TOOL POINT *6100 6000 4200 ALP *5150 *5150 4150 mm Lift Capacities Variable Adjustable Boom Counterweight: 7.4 t Road Mode All values are in kg. Load at maximum reach (stick nose/bucket pin) Load over front Load over rear Load over side Load point height Stick 2100 mm 7500 mm 6000 mm 4500 mm 3000 mm 1500 mm 0 mm 1500 mm 3000 mm 3000 mm 4500 mm 6000 mm 7500 mm TOOL POINT *5350 *5350 *400 *5000 *5000 *5000 503 ALP *550 *550 *550 *6050 *6050 *6050 4348 TOOL POINT *5250 *5250 *4800 *4500 *4500 *3700 *4350 *4350 3050 6443 ALP *5400 *5400 *4700 *5050 *5050 3400 *5050 *5050 3450 58 TOOL POINT *8650 *8650 *7750 *500 *500 *4650 *4400 *4400 *3800 *4100 3500 2550 7213 ALP 8000 8000 *7600 *6000 *6000 *4600 *4550 *4550 3400 *4750 3850 2750 6736 TOOL POINT *8750 *8750 *7400 *6600 *6600 *4550 *4850 4600 3550 *4150 3200 2300 753 ALP *7000 6650 *4500 *450 4550 3400 *4550 3450 2450 7144 TOOL POINT *10 150 *10 150 *7350 *7700 6350 *4500 *5200 4500 3450 *4300 3250 2300 *4200 3150 2250 7648 ALP *600 6650 *5100 *5250 4450 3300 *4400 3350 2400 7202 TOOL POINT *12 200 12 300 8650 *7750 6400 450 *5600 4350 3250 *300 3250 2300 7383 ALP *7650 6550 400 *5600 4350 3150 *4200 3500 2500 61 TOOL POINT *12 50 12 300 8500 *750 6650 4850 *5350 4350 3100 3650 2600 675 ALP *7800 6500 4700 *4450 4250 3050 *3800 2850 6256 TOOL POINT *6100 *6100 4650 ALP *5150 *5150 4600 mm * Limited by hydraulic rather than tipping load. Lift capacity ratings are based on ISO 10567:2007, they do not exceed 87% of hydraulic lifting capacity or 75% of tipping load. The load point is the center line of the bucket pivot mounting pin on the stick. The oscillating axle must be locked. Lifting capacities are based on the machine standing on a firm uniform supporting surface and the Variable Boom Cylinder adjusted to the maximum length. For lifting capacity including bucket and/or quick coupler, the respective weight has to be subtracted from above values. The use of a work tool attachment point to handle/ lift objects, could affect the machine lift performance. Always refer to the appropriate Operation and Maintenance Manual for specific product information. 6
Lift Capacities Variable Adjustable Boom Counterweight: 6.4 t Rail Mode Level Track All values are in kg. Stick 2100 mm Load at maximum reach (stick nose/bucket pin) Load over front Load over rear Load over side Load point height 3000 mm 4500 mm 6000 mm 7500 mm 7500 mm S54 + TOOL POINT *5350 *5350 4150 *5000 *5000 3350 S4 + TOOL POINT *5350 5200 3000 *5000 4600 2500 503 S54 + ALP *550 *550 4000 *6050 *6050 4200 S4 + ALP 500 5100 2850 6000 5200 3000 4348 6000 mm S54 + TOOL POINT *5250 *5250 4200 *4500 *4500 2700 *4350 *4350 2300 S4 + TOOL POINT *5250 5150 3000 *4500 4150 2100 4300 4000 1750 6443 S54 + ALP *5400 *5400 4100 *5050 *5050 2500 *5050 *5050 2600 S4 + ALP *5400 5050 250 4550 4150 1850 4550 4150 150 58 4500 mm S54 + TOOL POINT *8650 *8650 7050 *500 *500 4050 *4400 *4400 2700 *4100 *4100 1850 S4 + TOOL POINT 7650 6550 4300 5750 450 250 *4400 4200 2100 3750 3550 1400 7213 S54 + ALP 8000 8000 600 *6000 *6000 4000 *4550 *4550 2550 *4750 *4750 2000 S4 + ALP 7500 6400 4150 5750 450 2850 4500 4200 100 4000 3750 1500 6736 3000 mm S54 + TOOL POINT *8750 *8750 6700 *6600 *6600 350 *4850 *4850 2650 *4150 *4150 1650 S4 + TOOL POINT 7450 6350 4050 5600 4800 2800 4500 4200 2050 3550 3350 1200 753 S54 + ALP *7000 *7000 300 *450 *450 2550 *4550 *4550 1800 S4 + ALP 5500 4700 2800 4500 4150 100 3700 3500 1350 7144 1500 mm S54 + TOOL POINT *10 150 *10 150 6650 *7700 *7700 300 *5200 *5200 2600 *4300 *4300 1650 *4200 *4200 1600 S4 + TOOL POINT 7350 6250 4000 5250 4450 2800 4450 4100 2000 3550 3350 1200 3500 3300 1200 7648 S54 + ALP *600 *600 3850 *5250 *5250 2400 *4400 *4400 1700 S4 + ALP 5500 4700 2700 4350 4100 1800 3650 3400 1250 7202 0 mm S54 + TOOL POINT *12 200 *12 200 6250 *7750 *7750 3700 *5600 *5600 2400 *300 *300 1650 S4 + TOOL POINT 7200 6100 3750 5350 4550 2600 4300 4000 1800 3550 3350 1200 7383 S54 + ALP *7650 *7650 3600 *5600 *5600 2250 *4200 *4200 1750 S4 + ALP 5400 4700 2550 4300 4000 1650 3750 3500 1250 61 1500 mm S54 + TOOL POINT *12 50 *12 50 6100 *750 *750 3550 *5350 *5350 2250 *3550 1850 S4 + TOOL POINT 7100 6100 3650 5500 4700 2500 4250 4000 1600 *3550 1400 675 S54 + ALP *7800 *7800 3450 *4450 *4450 2250 *3800 2050 S4 + ALP 5350 4650 2400 4200 350 1600 *3800 1500 6256 S54 + TOOL POINT *6100 *6100 3350 3000 mm S4 + TOOL POINT 5350 4650 2350 S54 + ALP *5150 *5150 3300 S4 + ALP *5150 4650 2300 * Limited by hydraulic rather than tipping load. Lift capacity ratings are based on ISO 10567:2007, they do not exceed 87% of hydraulic lifting capacity or 75% of tipping load. The load point is the center line of the bucket pivot mounting pin on the stick. The oscillating axle must be locked. Lifting capacities are based on the machine standing on a firm uniform supporting surface and the Variable Boom Cylinder adjusted to the maximum length. For lifting capacity including bucket and/or quick coupler, the respective weight has to be subtracted from above values. The use of a work tool attachment point to handle/ lift objects, could affect the machine lift performance. Always refer to the appropriate Operation and Maintenance Manual for specific product information. mm 7
Lift Capacities Variable Adjustable Boom Counterweight: 7.4 t Rail Mode Level Track All values are in kg. Stick 2100 mm Load at maximum reach (stick nose/bucket pin) Load over front Load over rear Load over side Load point height 3000 mm 4500 mm 6000 mm 7500 mm 7500 mm S54 + TOOL POINT *5350 *5350 4550 *5000 *5000 3700 S4 + TOOL POINT *5350 5100 3100 *5000 4500 2550 503 S54 + ALP *550 *550 4400 *6050 *6050 4650 S4 + ALP 5800 5000 250 500 5100 3100 4348 6000 mm S54 + TOOL POINT *5250 *5250 4600 *4500 *4500 3000 *4350 *4350 2550 S4 + TOOL POINT *5250 5050 3100 *4500 350 2150 4200 300 1800 6443 S54 + ALP *5400 *5400 4500 *5050 *5050 2800 *5050 *5050 2850 S4 + ALP *5400 450 3050 4450 350 100 4550 350 2000 58 4500 mm S54 + TOOL POINT *8650 *8650 7650 *500 *500 4450 *4400 *4400 3000 *4100 *4100 2100 S4 + TOOL POINT 7550 6350 4400 5650 4850 3050 *4400 4000 2150 3700 3450 1500 7213 S54 + ALP 8000 8000 7550 *6000 *6000 4350 *4550 *4550 2800 *4750 *4750 2250 S4 + ALP 7400 6300 4300 5650 4850 250 4500 4000 150 300 3650 1550 6736 3000 mm S54 + TOOL POINT *8750 *8750 7350 *6600 *6600 4350 *4850 *4850 250 *4150 *4150 1850 S4 + TOOL POINT 7350 6150 4150 5500 4700 200 4400 4000 2150 3450 3250 1300 753 S54 + ALP *7000 *7000 4300 *450 *450 2800 *4550 *4550 2000 S4 + ALP 5400 4600 200 4400 4000 150 3650 3400 1400 7144 1500 mm S54 + TOOL POINT *10 150 *10 150 *7350 *7700 *7700 4500 *5200 *5200 200 *4300 *4300 1850 *4200 *4200 1800 S4 + TOOL POINT 7150 6050 4150 5150 4350 200 4350 4000 2050 3450 3250 1300 3400 3200 1200 7648 S54 + ALP *600 *600 4200 *5250 *5250 2700 *4400 *4400 150 S4 + ALP 5400 4600 2800 4250 4000 100 3550 3300 1300 7202 0 mm S54 + TOOL POINT *12 200 *12 200 600 *7750 *7750 4100 *5600 *5600 2700 *300 *300 1850 S4 + TOOL POINT 7000 500 3850 5250 4450 2700 4200 300 100 3450 3250 1300 7383 S54 + ALP *7650 *7650 4000 *5600 *5600 2550 *4200 *4200 2000 S4 + ALP 5300 4500 2650 4200 300 1700 3650 3400 1350 61 1500 mm S54 + TOOL POINT *12 50 *12 50 6800 *750 *750 350 *5350 *5350 2550 *3550 2100 S4 + TOOL POINT 7000 500 3800 5400 4600 2600 4250 300 1700 3500 1400 675 S54 + ALP *7800 *7800 3800 *4450 *4450 2450 *3800 2300 S4 + ALP 5250 4450 2450 4200 3850 1650 3700 1550 6256 S54 + TOOL POINT *6100 *6100 3750 3000 mm S4 + TOOL POINT 5350 4450 2450 S54 + ALP *5150 *5150 3700 S4 + ALP *5150 4450 2350 * Limited by hydraulic rather than tipping load. Lift capacity ratings are based on ISO 10567:2007, they do not exceed 87% of hydraulic lifting capacity or 75% of tipping load. The load point is the center line of the bucket pivot mounting pin on the stick. The oscillating axle must be locked. Lifting capacities are based on the machine standing on a firm uniform supporting surface and the Variable Boom Cylinder adjusted to the maximum length. For lifting capacity including bucket and/or quick coupler, the respective weight has to be subtracted from above values. The use of a work tool attachment point to handle/ lift objects, could affect the machine lift performance. Always refer to the appropriate Operation and Maintenance Manual for specific product information. mm 8
Lift Capacities Variable Adjustable Boom Counterweight: 6.4 t Rail Mode 200 mm Cant All values are in kg. Stick 2100 mm Load at maximum reach (stick nose/bucket pin) Load over front Load over rear Load over side Load point height 3000 mm 4500 mm 6000 mm 7500 mm 7500 mm S54 + TOOL POINT *5350 *5350 3100 *5000 *5000 2550 S4 + TOOL POINT 3550 2250 1850 3250 2000 1600 503 S54 + ALP *550 *550 3200 *6050 *6050 3200 S4 + ALP 3500 2150 2000 3550 2200 150 4348 6000 mm S54 + TOOL POINT *5250 *5250 3250 *4500 *4500 2100 *4350 *4350 1700 S4 + TOOL POINT 3850 2400 2000 3150 100 1350 200 1650 1000 6443 S54 + ALP *5400 *5400 3200 *5050 *5050 150 *5050 *5050 100 S4 + ALP 3800 2350 2000 250 1750 1200 3150 1800 1150 58 4500 mm S54 + TOOL POINT *8650 *8650 *500 *500 3150 *4400 *4400 2100 *4100 *4100 1350 S4 + TOOL POINT 5050 3200 4050 2450 100 3400 150 1300 200 1550 800 7213 S54 + ALP 8000 8000 *6000 *6000 3100 *4550 *4550 2050 *4750 *4750 1450 S4 + ALP 5000 3100 3850 2400 1850 3400 150 1250 3050 1650 800 6736 3000 mm S54 + TOOL POINT *8750 *8750 *6600 *6600 3050 *4850 *4850 2100 *4150 *4150 1150 S4 + TOOL POINT 5600 3400 4350 2500 1750 3650 2000 1300 3000 1550 600 753 S54 + ALP *7000 *7000 3000 *450 *450 2050 *4550 *4550 1250 S4 + ALP 4300 2450 1700 3650 2000 1200 3150 1600 650 7144 1500 mm S54 + TOOL POINT *10 150 *10 150 5600 *7700 *7700 3000 *5200 *5200 2100 *4300 *4300 1250 *4200 *4200 1100 S4 + TOOL POINT 6350 3750 2550 4700 2550 1750 350 2100 1300 3300 1650 700 3200 1600 550 7648 S54 + ALP *600 *600 3000 *5250 *5250 150 *4400 *4400 1200 S4 + ALP 400 2750 1750 4000 2150 1150 3400 1700 600 7202 0 mm S54 + TOOL POINT *12 200 *12 200 5600 *7750 *7750 250 *5600 *5600 100 *300 *300 1150 S4 + TOOL POINT 7300 4150 2400 5400 200 1650 4350 2250 1100 3650 1850 500 7383 S54 + ALP *7650 *7650 200 *5600 *5600 1800 *4200 *4200 1200 S4 + ALP 5500 3000 1600 4400 2250 1000 3850 150 600 61 1500 mm S54 + TOOL POINT *12 50 *12 50 5050 *750 *750 2850 *5350 *5350 1750 *3550 1300 S4 + TOOL POINT 7800 5000 2300 6050 3400 1550 4750 2550 50 2250 650 675 S54 + ALP *7800 *7800 2750 *4450 *4450 1650 *3800 1400 S4 + ALP 500 3350 1500 *4450 2500 800 2400 700 6256 S54 + TOOL POINT *6100 *6100 2700 3000 mm S4 + TOOL POINT 5050 3650 1400 S54 + ALP *5150 *5150 2600 S4 + ALP *5150 3650 1300 * Limited by hydraulic rather than tipping load. Lift capacity ratings are based on ISO 10567:2007, they do not exceed 87% of hydraulic lifting capacity or 75% of tipping load. The load point is the center line of the bucket pivot mounting pin on the stick. The oscillating axle must be locked. Lifting capacities are based on the machine standing on a firm uniform supporting surface and the Variable Boom Cylinder adjusted to the maximum length. For lifting capacity including bucket and/or quick coupler, the respective weight has to be subtracted from above values. The use of a work tool attachment point to handle/ lift objects, could affect the machine lift performance. Always refer to the appropriate Operation and Maintenance Manual for specific product information. mm
Lift Capacities Variable Adjustable Boom Counterweight: 7.4 t Rail Mode 200 mm Cant All values are in kg. Stick 2100 mm Load at maximum reach (stick nose/bucket pin) Load over front Load over rear Load over side Load point height 3000 mm 4500 mm 6000 mm 7500 mm 7500 mm S54 + TOOL POINT *5350 *5350 3100 *5000 *5000 2600 S4 + TOOL POINT 3350 2050 2700 3100 1800 2250 503 S54 + ALP *550 *550 3500 *6050 *6050 3500 S4 + ALP 3300 150 2000 3400 2000 2000 4348 6000 mm S54 + TOOL POINT *5250 *5250 3250 *4500 *4500 2150 *4350 *4350 1750 S4 + TOOL POINT 3650 2150 2650 3000 1650 100 2800 1500 1550 6443 S54 + ALP *5400 *5400 3550 *5050 *5050 2200 *5050 *5050 2100 S4 + ALP 3600 2100 2000 250 1600 1200 250 1600 1150 58 4500 mm S54 + TOOL POINT *8650 *8650 *500 *500 3150 *4400 *4400 2150 *4100 *4100 1400 S4 + TOOL POINT 4800 200 3850 2200 2500 3200 1750 1800 2750 1400 1150 7213 S54 + ALP 8000 8000 *6000 *6000 3400 *4550 *4550 2250 *4750 *4750 1650 S4 + ALP 4750 2850 3800 2200 1850 3200 1750 1250 2850 1450 800 6736 3000 mm S54 + TOOL POINT *8750 *8750 *6600 *6600 3050 *4850 *4850 2100 *4150 *4150 1200 S4 + TOOL POINT 5250 3100 4100 2250 2300 3400 1800 1700 2850 1400 00 753 S54 + ALP *7000 *7000 3300 *450 *450 2250 *4550 *4550 1400 S4 + ALP 4100 2200 1750 3450 1800 1200 250 1450 650 7144 1500 mm S54 + TOOL POINT *10 150 *10 150 5850 *7700 *7700 3000 *5200 *5200 2100 *4300 *4300 1300 *4200 *4200 1150 S4 + TOOL POINT 6050 3450 2500 4450 2250 2250 3750 100 1700 3100 1500 00 3050 1450 750 7648 S54 + ALP *600 *600 3350 *5250 *5250 2150 *4400 *4400 1350 S4 + ALP 4650 2450 1750 3750 150 1150 3200 1550 600 7202 0 mm S54 + TOOL POINT *12 200 *12 200 5850 *7750 *7750 250 *5600 *5600 150 *300 *300 1200 S4 + TOOL POINT 650 3800 2400 5100 2600 2100 4100 2050 1500 3450 1650 750 7383 S54 + ALP *7650 *7650 3200 *5600 *5600 2000 *4200 *4200 1400 S4 + ALP 5250 2700 1600 4150 2050 1000 3650 1750 600 61 1500 mm S54 + TOOL POINT *12 50 *12 50 4850 *750 *750 2850 *5350 *5350 1750 *3550 1350 S4 + TOOL POINT 700 4400 2850 6050 3100 2000 4700 2300 1200 2000 800 675 S54 + ALP *7800 *7800 3100 *4450 *4450 100 *3800 1650 S4 + ALP 550 3050 1500 *4450 2250 850 2200 700 6256 S54 + TOOL POINT *6100 *6100 2650 3000 mm S4 + TOOL POINT 5400 2800 1700 S54 + ALP *5150 *5150 250 S4 + ALP *5150 3850 1300 * Limited by hydraulic rather than tipping load. Lift capacity ratings are based on ISO 10567:2007, they do not exceed 87% of hydraulic lifting capacity or 75% of tipping load. The load point is the center line of the bucket pivot mounting pin on the stick. The oscillating axle must be locked. Lifting capacities are based on the machine standing on a firm uniform supporting surface and the Variable Boom Cylinder adjusted to the maximum length. For lifting capacity including bucket and/or quick coupler, the respective weight has to be subtracted from above values. The use of a work tool attachment point to handle/ lift objects, could affect the machine lift performance. Always refer to the appropriate Operation and Maintenance Manual for specific product information. mm 10
Bucket Specifications and Compatibility Variable Adjustable Boom 2100 mm Stick Road Rail without Cant Width Capacity Weight Fill Counterweight Counterweight mm m3 kg % 6.4 t 7.4 t 6.4 t 7.4 t Without Quick Coupler General Duty (GD) 750 0.4 464 100% 1100 0.7 583 100% 1200 0.1 651 100% Maximum load with pin-on (payload + bucket) kg 2000 2250 1600 1800 With Pin Grabber Quick Coupler General Duty (GD) 750 0.4 464 100% 1100 0.7 583 100% 1200 0.1 651 100% Maximum load with pin-on (payload + bucket coupler) kg 2000 2250 1600 1800 With Quick Coupler (CW/CWs) Ditch Cleaning (DC) General Duty (GD) Heavy Duty (HD) With TR14 (Tilt Rotator) 1800 1.14 646 100% X 2100 1.45 738 100% X X 600 0.35 421 100% 750 0.4 454 100% 00 0.62 514 100% 1100 0.7 573 100% 1200 0.1 623 100% 1200 0.1 64 Maximum load with coupler (payload + bucket coupler) 100% kg 2000 2250 1600 1800 General Duty (GD) 600 0.35 421 100% 750 0.4 454 100% 00 0.62 514 100% 1100 0.7 573 100% 1200 0.1 623 100% 1300 1.00 653 100% 1400 1.0 683 100% X Maximum load with coupler (payload + bucket coupler) kg 2000 2250 1600 1800 Capacity based on ISO 7451:2007. Bucket weight with General Duty tips. Bucket recommendation based on S54 rail type. Bucket recommendation based on no rail Cant. Specialized work tools are available. Please contact your dealer for further information. Maximum Material Density: 2100 kg/m3 1800 kg/m3 1500 kg/m3 1200 kg/m3 00 kg/m3 X Not Recommended (stability) Caterpillar recommends using appropriate work tools to maximize the value customers receive from our products. Use of work tools, including buckets, which are outside of Caterpillar s recommendations or specifications for weight, dimensions, flows, pressures, etc. may result in less-than-optimal performance, including but not limited to reductions in production, stability, reliability, and component durability. Improper use of a work tool resulting in sweeping, prying, twisting and/or catching of heavy loads will reduce the life of the boom and stick. 11
Attachments Offering Guide* PIN-ON ATTACHMENTS Counterweight 6.4 t 7.4 t Boom Type Stick Length Variable Adjustable Hydraulic Hammers H110Es 2.10 m H115Es H120Es Demolition and Sorting Grapples G310B D/R G310 GC G313 GC Compactors (Vibratory Plate) CVP75 Tilt Rotators TRS14-Pin-On/S60 Pin Grabber Couplers TRS14-Pin-On/CW Cat PG Dedicated Quick Couplers CW-20 These couplers are available for the M323F. CAT PIN GRABBER COUPLER ATTACHMENTS CW-20s Counterweight 6.4 t 7.4 t Boom Type Stick Length Variable Adjustable Hydraulic Hammers H110Es 2.10 m H115Es Compactors (Vibratory Plate) CVP75 CW-20 COUPLER ATTACHMENTS Counterweight 6.4 t 7.4 t Boom Type Variable Adjustable Stick Length 2.10 m Hydraulic Hammers H110Es H115Es Compactors (Vibratory Plate) CVP75 CW-20s COUPLER ATTACHMENTS Counterweight 6.4 t 7.4 t Boom Type Variable Adjustable Stick Length 2.10 m Hydraulic Hammers H110Es H115Es Compactors (Vibratory Plate) CVP75 *Offerings not available in all areas. Matches are dependent on Wheeled Excavator configurations. Consult your Cat dealer to determine what is offered in your area and for proper work tool match. D Demolition shells. R Recycling shells. Attachment recommendation based on S54 rail type. Attachment recommendation based on no rail Cant. Specialized work tools are available. Please contact your dealer for further information. 12
M323F Standard and Optional Equipment Standard and Optional Equipment Standard and optional equipment may vary. Consult your Cat dealer for details. Standard Optional UNDERCARRIAGE AND STRUCTURES Rail wheels insulated according to local regulations Road and rail all-wheel drive 6.4 t counterweight 7.4 t counterweight Two speed hydrostatic transmission on road or rail Independent rail hydrostatic transmission, one motor per rail axle Automatic rail axle lock Automatic lock mode for oscillating front road axle and service brake Heavy-duty rail axles with advanced disc brake system and travel motor with adjustable braking force Travel restraint bracket for clamshell/grapple Towing bar Left- and right-side steps One or two additional tool boxes at undercarriage steps Trailer coupling unit with manual or automatic lock Roading package Standard Optional HYDRAULIC SYSTEM Adjustable hydraulic sensitivity One medium pressure circuit Two medium pressure circuits Auxiliary hydraulic selection button, controlled through left console lever Dedicated swing pump Load sensing hydraulic system Programmable flow and pressure for up to 10 attachments Auxiliary circuit pedal Biodegradable hydraulic oil Bio oil micro-filtration unit High pressure circuit control valve Heavy lift mode Medium pressure auxiliary boom lines High pressure auxiliary boom lines SAFETY AND SECURITY Emergency stop button Backup electro-hydraulic pump for rail emergencies Safety decals for rail certification Pneumatic system for rail trailer or rail car brakes Rear and right-side cameras ROPS operator and secondary cab Stick lowering control valve (SLCV) and boom lowering control valve (BLCV) including overload warning device Pin code engine start prevention Variable Adjustable (VA) boom includes foreboom lowering control valve (FLCV) Automatic swing brake Emergency kit Emergency coupling unit (continued on next page) 13
M323F Standard and Optional Equipment Standard and Optional Equipment (continued) Standard and optional equipment may vary. Consult your Cat dealer for details. Standard Optional Standard Optional BOOM AND STICK PRIMARY CAB 5.2 m VA boom, 2.1 m stick Bolt-on falling object guard system SERVICE AND MAINTENANCE (FOGS) capability Ground-level fuel and engine oil filters FM radio with speakers and fluid taps High resolution, full graphic and Centralized lubrication for color instrument panel display undercarriage and rail bogies Pilot operated joysticks Auto-lubricating system Air conditioner, heater, and defroster ENGINE 24V lighter Cat C4.4 ACERT, Stage IV engine Bottle holder Altitude 3000 m capability without de-rate Top and bottom mounted, intermittent, parallel wiper and washer Electric fuel priming pump Washable floor mat with Automatic starting aid storage compartment ELECTRICAL SYSTEM Interior lighting with door switch 100 A alternator Tiltable left side console with lock-out for all controls Main shut-off switch Steering lock device 12V 10 A power supply in primary and secondary cab Adjustable steering column Two front and two rear roading lights Windshield and skylight sunshade Right side, VA boom, and stick flood lights Adjustable travel alarm Cruise control system LCD screens for hydrostatic deceleration power and rail trailer brake pressure Refueling pump Road/rail mode button and signal International Union of Railways (UIC) certified rail lights On/off-tracking control Joystick for hydrostatic deceleration Electric and pneumatic signal/ Power and rail trailer brakes control warning horn SECONDARY CAB 24V 10 A power supply at stick end Retractable seat belt Back door and openable roof for maintenance access to top part of the upper frame Rear window emergency exit Backup electric horn Warning beacon control Support parts for rail safety devices Main machine power switch 14
For more complete information on Cat products, dealer services, and industry solutions, visit us on the web at www.cat.com AEXQ2372 (07-2018) (France, Germany) 2018 Caterpillar All rights reserved Materials and specifications are subject to change without notice. Featured machines in photos may include additional equipment. See your Cat dealer for available options. CAT, CATERPILLAR, SAFETY.CAT.COM, their respective logos, Caterpillar Yellow and the Power Edge trade dress, as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.