Boom truck 3 tons national series : ft to 7ft JIB : ft JIB OFFSETS:
NOTES: portland office: 53.23.11 seattle office: 2.74.4
features Why Buy a National Crane Series? 3 USt (32. t) Rating The provides a 3 USt (32.t) capacity at a ft (1.2 m) radius, a 9% increase over the Series 14. 3 USt (32. t) maximum capacity 1 ft (5. m) maximum vertical reach* 1 ft (41. m) maximum vertical hydraulic reach* Load Moment Indicator system (LMI) Proportional boom extension High performance planetary winch Vickers PVH 1 pressure compensated, load sensing, axial piston, variable volume pump direct mounts to PTO * Maximum vertical reach is ground-level to boom tip height at maximum extension and angle with outriggers/stabilizers fully extended. 7 ft (3.71 m) Five-section Boom The long boom allows the operator to perform more lifts without the use of a jib, reducing setup time and improving efficiency. Overload Protection All National Crane boom trucks are equipped with overload protection: Load Moment Indicator (LMI) standard on all Series machines. LMI display and CPU are weatherproof. LCD display is visible in full or low light. All crane load lifting values are displayed simultaneously. Stronger Torsion Box The stronger standard torsion box improves rigidity, reduces truck frame flex and reduces the need for counterweight. y-reeve Boom Tip and Sheave Blocks These standard features simplify rigging changes by decreasing the time needed to change line reeving. Pre-painted Components Painting crane components before assembly reduces the possibility of rust, improves serviceability and enhances the appearance of the machine. Easy Glide Boom Wear Pads Reduce the conditions that cause boom chatter and vibration. The net result is smoother crane operation. Deluxe Operator s Cab Rigid galvanized steel structure, well insulated, with ample safety glass for operator visibility and comfort. Multi-position seat with arm rest controls, ventilation fans, diesel heater, wipers. Optional air-conditioning is available. Outrigger Outrigger span of 24.7 ft (7.53 m) when fully extended; 17.5 ft (5.33 m) at midspan. Ground-level outrigger controls on both sides. In-cab outrigger controls for all functions. Front bumper stabilizer for stable base over front. Improved Ser viceability Boom sections are supported by one hydraulic extend cylinder, minimizing maintenance. Bearings on the boom extend and retract cables can be greased through access holes in the boom side plates. Pre-paint reduces rust. Electronic versions of manuals available through Manitowoc Crane Care. New State-of-the-art Control V alve Provides smoother operation. The new load-sensing, pressure-compensated design greatly enhances function meterability, eliminates parts, reduces repair costs and improves the machine s serviceability. National Crane Is the Market Leader National Crane is number one in the production of commercial truck-mounted boom trucks, with more than, units sold. National Crane has many programs and people directly and indirectly involved to provide our customers with reliable products. National Crane has the boom truck industry s leading test program. Every structural part of the crane is cycle tested, some up to, cycles at full capacity. In addition to cycle testing, each model is subjected to state-of-the-art strain gauge testing that measures metal deformation as small as one one-millionth of an inch. The net result is that weak areas are caught in test, not on job sites where costly downtime occurs. Parts are available for all National Crane machines for the life of the crane. National Crane has a formalized quality program and is ISO 91 approved. portland office: 53.23.11 seattle office: 2.74.4
mounting configurations The configurations are based on the Series with an 5% stability factor. The complete unit must be installed in accordance with factory requirements and a test performed to determine actual stability and counterweight requirements since individual truck chassis vary. *CLEAR OF OBSTRUCTIONS (MUFFLERS, EXHAUST STACKS, ETC.) ON TOP OF TRUCK FRAME FOR FULL FOOT WIDTH. Configuration 1 Working area...3 Gross Axle Weight Rating Front...2, lb (972 kg)* Gross Axle Weight Rating Rear...34, lb ( 422 kg)* Gross Vehicle Weight Rating...54, lb (24 494 kg)* Wheelbase... in ( cm) Cab to Axle/trunnion (CA/CT)...1 in (7 cm) After Frame (AF)...92 in (2.44 m) minimum Frame Section Modulus (SM), front axle to end of afterframe, w/11, PSI ( MPa)...3 in 3 (492 cm 3 ) Stability Weight, Front...9, lb (441 kg) minimum** Stability Weight, Rear...,5 lb (3 kg) minimum** Estimated Average Final Weight...51, lb (23 57 kg)*** The diagram shows the 3 working area achieved with the front stabilizer (standard on the Series ). The front stabilizer is required when extending the boom and lifting loads over the front of the truck. A minimum of 1-in 3 (14 cm 3 ) section modulus at 11, psi ( MPa) is required from the rear of the front spring hanger forward to the front stabilizer. Integral front frame extension requested. *Required to mount basic crane with 3 ft (9. m) jib option. Additional options or heavier base chassis weights will require additional axles or a GVWR in excess of 54, lb (24 494 kg); in some states, special permits for overload are required. Estimated axle scale weights prior to installation of crane, stabilizers and subbase for 5% stability. ***Includes basic crane without jib, 1 gal (3 L) fuel tank and two workers in cab. Note: Chassis will require extended front frame rails for SFO addition. MINIMUM TRUCK Many factors must be considered in the selection of proper truck for a series crane. Items which must be considered are: 1. Axle Rating. Axle ratings are determined by the axles, tires, rims, springs, brakes, steering and frame strength of the truck. If any one of these components is below the required rating, the gross axle rating is reduced to its weakest component value. 2. Wheelbase (WB), Cab-to-Trunnion (CT) and Bare Chassis Weight. The wheelbase, CT and chassis weights shown are required so the basic can be legally driven in most states and meet stability requirements. The dimensions given assume the sub-base is installed properly behind the truck cab. If exhaust stacks, transmission protrusions, etc., do not allow aclose installation to the cab, the WB and CT dimensions must be increased. Refer to the Mounting Configuration pages for additional information. 3. Truck Frame. Try to select a truck frame that will minimize or eliminate frame reinforcement or extension of the after frame (AF). Many frames are available that have the necessary REQUIREMENTS after frame (AF) section modulus (S.M.) and resistance to bending moment (RBM) so that reinforcing is not required. The front hydraulic jack is used for a 3 working range around the truck. The frame under the cab through the front suspension must have the minimum S.M. and RBM because reinforcing through the front suspension is often difficult because of engine, radiator mounts and steering mechanics. See Truck Requirements and Frame Strength information above for the necessary section modulus and resistance to bending moment values. 4. Additional Equipment. In addition to the axle ratings, wheelbase, cab-to-axle requirements and frame, it is recommended that the truck is equipped with electronic engine control, increased cooling and a transmission with a PTO opening available with an extra heavy duty PTO. A conventional cab truck should be used for standard crane mounts. 5. Neutral Start Switch. The chassis must be equipped with a switch that prevents operation of the engine starter when the transmission is in gear. portland office: 53.23.11 seattle office: 2.74.4
specifications Boom and Jib Combinations Data Available in three basic models: four-section, 13 four-section and 7 five- Model Equipped with a - (9.-24. m) four-section boom. Maximum tip height is 7 ft (.52 m). - (9.-24. m) four-section boom Model 13 Equipped with a -13 ft (9.-.4 m) four-section boom. This model can be equipped with a ft (9. m) single section side-stowing jib providing a maximum tip height of 142 ft (43.29 m), or a - ft (9.-1.7 m) side-stowing folding jib, providing a vertical reach of 1 ft (5. m). Contact factory for information on angling jib. - 13 ft (9.-.4 m) four-section hydraulic boom - 13 ft (9.-.4 m) four-section hydraulic boom FJ ft (9. m) single-section jib - 13 ft (9.-.4 m) four-section hydraulic boom FJM - ft (9.-1.7 m) single-section jib Model 7 Equipped with a -7 ft (9.-3.72 m) five-section hydraulic boom. This model can be equipped with a ft (9. m) single-section side-stowing jib. Maximum tip height w/ ft (9. m) jib is 1 ft (5. m). - 7 ft (9.-3.72 m) five-section hydraulic boom - 7 ft (9.-3.72 m) five-section hydraulic boom FJ ft (9. m) single-section manual jib Note: maximum tip height is measur ed with outrigger s/stabilizers fully extended. Winch Data All winch pulls and speeds are shown on the fifth layer. Winch line pulls would increase on the first, second, third and fourth layers. Winch line speed would decrease on the first, second, third and fourth layers. Winch line pulls may be limited by the winch capacity or the ANSI 5 to 1 cable safety factor. Winch Standard Planetary Winch Low Standard Planetary Winch High Cable Supplied 5/ in diameter rotation resistant 1 x 19 IWRC Average Breaking Srength,4 lb (93 kg) Same as corresponding cable data shown above 9, lb (42 kg) fpm (2 m/m) 4,5 lb (241 kg) 41 fpm (4 m/m) 1, lb (1 kg) 13 fpm ( m/m) 9, lb (42 kg) fpm (2 m/m) 27, lb (247 kg) fpm (21 m/m) 13,5 lb (3 kg) 137 fpm (42 m/m) 3, lb (1329 kg) 51 fpm (1 m/m) 1, lb (1 kg) 13 fpm ( m/m), lb (24 kg) 41 fpm ( m/m) 22,5 lb ( kg) 2 fpm ( m/m) 54, lb (24494 kg) 34 fpm (1 m/m) 27, lb (247 kg) fpm (21 m/m) 3, lb (2577 kg) 29 fpm ( m/m),5 lb (142 kg) 59 fpm (1 m/m) 72, lb (329 kg) 2 fpm (7 m/m) 3, lb (1329 kg) 51 fpm (1 m/m) Winch Full Drum Pull Allowable Cable Pull Standard planetary 4,5 lb (high speed) 9, lb & Auxiliary planetary 9, lb (low speed) Aux Boom Head 1 lb ( kg) 5 USt Downhaul Weight 1 lb (2 kg) USt 1 Sheave Block 3 lb (1 kg) USt 2 Sheave Block 4 lb (29 kg) USt 3 Sheave Block lb (395 kg) 3 USt 4 Sheave Block 9 lb (44 kg) portland office: 53.23.11 seattle office: 2.74.4
Load Rating Chart: Series (24. m) Boom/Fullspan Outrigger 24. ft (7.51m) LENGTH IN FEET 3 47 5 4 3 2 1-1 FULL-SPAN OUTRIGGER 24. FT. ' 1 2 3 4 5 IN FEET 9 5 4 3 2 1 HEIGHT IN FEET accessories or loads within 1 ft (3m) of live power lines Always level the crane with the level indicator located on the crane. Load Rating Chart: Series (24. m) Boom/Fullspan Outrigger 24. ft (7.51m) TO FOOT (FEET) FT 47 FT 3 FT FT SERIES (24. M) /MIDSPAN OUTRIGGER 24. FT (7.51 M) 1 2 3 4 5 71.5 7 2.5 5 43.5 27 72, 4,, 4, 39,5 3, 23, 17,5 77.5.5 72.5 9.5 2.5.5 47 3.5 2.5, 44,1 39, 34,3 27,9 23, 1, 14,1 11,4 9, 77.5 54.5 4.5 41.5 34.5 9,2 3,,4 21,4 1,3 14,3 11, 9,,1, 5, 5,5 7.5 71 7 3 59 54.5 5 39 33 13 2, 22,3 19,1 1,5 14,5 11, 9,,2,95 5, 4,9 4, 3,5 3,3 NOTE: 1. All capacities are in pounds, angles in degrees, radius in feet. 2. Loaded boom angles are given as reference only. 3. Shaded areas are structurally limited capacities. portland office: 53.23.11 seattle office: 2.74.4
Load Rating Chart: Series (24. m) Boom/Midspan Outrigger 17.5 ft (5.33 m) LENGTH IN FEET 3 47 5 4 3 2 1 MID-SPAN OUTRIGGER 17.5 FT. ' -1 1 2 3 4 5 IN FEET 9 5 4 3 2 1 HEIGHT IN FEET accessories or loads within 1 ft (3m) of live power lines Always level the crane with the level indicator located on the crane. Load Rating Chart: Series (24. m) Boom/Midspan Outrigger 17.5 ft (5.33 m) SERIES (24. M) /MID- SPAN OUTRIGGER 17.5 FT (5.33 M) (FEET) 1 2 3 4 5 ft 47 ft TO 13 ft RATED S WITHOUT JIB ft ft 13 ft (ft) 72,.7 72, 71.5 71. 4, 77.5, 4, 17 7.5,7. 42,.5 44,1 3.3 4, 7.4 37, 2.5. 39,5 4,73.1 32, 72.5.2 39, 2, 77.5 2 44 21,3 7.3 22,.4 21,., 2 27.4 13,3 39,51.1 14, 9.5 71.3 34,3 14,1 7. 13,5 3 54.7 9, 7.2 9, 73. 9, 43.5 22,1 2.5 22, 4.2 7,1 3.2 7,2. 7,2 427 14,14.5 5, 5.9 14,5 5, 7.4 4.5 5,4.3 3, 54.4 4, 4.2 4, 5 1.1 2, 47 49. 1,2 2,95.9 59.5 3, 44.5 2, 57.5 2, 3 7,5 54 3. 1, 54 1,5.5 32.3 5, 95 5.4 41, 24.2 4 4.5 1,1 2,3 41.5 LENGTH ft ft 13 ft 1, RATED REDUCTIONS WITH JIB - ft JIB STOWED Reduce load lb Reduce load lb Reduce load lb Reduce load lb 4, 34 24.5.5 3 ft ft JIB 24 3 4 5,2 3, ALL,5,9 3, 2, 5 ft JIB 23,2 ALL 14, 71 4, 1,4 4.5 3, 5 2,4 7, 3 9 1, 5,9 4, 3, 2, 2,1 - ft JIB ERECTED AT ft LENGTH Reduce load 2,3 lb Reduce load 2, lb Reduce load 1,9 lb Reduce load 1, lb 2, 7.5 5.5 54 49.5 44 3.5 32 24.5 2, 22,3, 1, 7,5, 4, 3, 2,5 2,2 1, 1,2 NOTE: 1. All capacities are in pounds, angles in degrees, radius in feet. 2. Loaded boom angles are given as reference only. 3. Shaded areas are structurally limited capacities. portland office: 53.23.11 seattle office: 2.74.4
Load Rating Chart: Series 13 (1.7 m) Boom with - ft (9.-1.7 m) Jib/Fullspan Outrigger 24. ft (7.51 m) HOOK ELEVATION IN FEET 1 1 14 13 11 1 9 5 4 3 2 1 13 LENG T H IN FEET 134 O O -1 O C/L 1 2 3 4 5 9 1 OPERATING FROM C/L ROTATION IN FEET WITH UN O O O O O 3 O 13 FULL-SPAN OUTRIGGER 24. FT. 13 ft - ft JIB O 2 O 5 O 4 O 3 O O 1 O 5 O O O 43 O STABILITY LIMIT LINE WITH 4 lb BLOCK STRUCTURAL LIMIT LINE WITH ft JIB DEPLOYED STRUCTURAL LIMIT LINE WITH ft JIB DEPLOYED accessories or loads within 1 ft (3m) of live power lines Always level the crane with the level indicator located on the crane. Load Rating Chart: Series 13 (1.7 m) Boom with - ft (9.-1.7 m) Jib/Fullspan Outrigger 24. ft (7.51 m) SERIES 13 (24. M) WITH - FT (9.-1.7 M) JIB/FULLSPAN OUTRIGGER 24. FT (7.51 M) TO 13 ft WITHOUT JIB (ft) ft ft 13 ft 1 2 3 4 5 5 9 95 1.7 71. 7.5 3.3 5. 44 27.3 72, 4,, 4, 39,5 3,5 23, 1,5 7. 7.4 73.1 7.5 1.5.2 4.3 4.5.1 1.7 42, 37, 32,,5 21, 1, 14,3 11,4 9,3 7,,.2.4 71. 7.7 3.7 59.5 54.9 5.3.2 39.5 33.7 2, 21, 17,5,2 13,4 11, 9,5,,5 5,3 4,4 3, 3, 2,. 7. 74 71.1.1.2 2 5. 51.3 47.4 43.2 3.7 33.7 27.9 2.5 7.2, 13,5, 11, 1, 9,,, 5,5 4, 3, 3,5 2,5 2,5 1, 1, 9 5 RATED REDUCTIONS WITH JIB 24 37 4 59 9 7 7 95 29 59 71 3 94 14 113 ft JIB 5 4 ft JIB 5 ALL,5 7,5,4 5,1 3,9 2, 1,9 1, ALL 4, 3, 3,2 2, 2, 1, 1,3 LENGTH ft ft 13 ft - ft JIB STOWED Reduce load lb Reduce load lb Reduce load lb Reduce load lb - ft JIB ERECTED AT ft LENGTH Reduce load 2,3 lb Reduce load 2, lb Reduce load 1,9 lb Reduce load 1, lb NOTE: portland office: 53.23.11 seattle office: 2.74.4
Load Rating Chart: Series 13 (1.7 m) Boom with - ft (9.-1.7 m) Jib/Midspan Outrigger 17.5 ft (5.33 m) HOOK ELEVATION IN FEET 1 1 14 13 11 1 9 5 4 3 2 1 OPERATING FROM C/L ROTATION IN FEET WITH UN LENGTH IN FEET 13 134 O O O O C/L 1 2 3 4 5 O 3 O O 5 O -1 O O 4 O O 3 O O 2 O O 1 O 5 O O 13 MID-SPAN OUTRIGGER 17.5 ft 13 ft - ft JIB STABILITY LIMIT LINE WITH 4 lb BLOCK STRUCTURAL LIMIT LINE WITH ft JIB DEPLOYED STRUCTURAL LIMIT LINE WITH ft JIB DEPLOYED accessories or loads within 1 ft (3m) of live power lines Always level the crane with the level indicator located on the crane. Load Rating Chart: Series 13 (1.7 m) Boom with - ft (9.-1.7 m) Jib/Midspan Outrigger 17.5 ft (5.33 m) SERIES 13 (24. M) WITH - FT (9.-1.7 M) JIB/MID- SPAN OUTRIGGER 17.5 FT (5.33 M) TO 13 ft WITHOUT JIB (ft) ft ft 13 ft 1 2 3 4 5.7 71. 7.5 3.3 5. 44 27.4 72, 4,, 4, 39,5 21,3 13,3 7. 7.4 73.1 7.3 1.1 54.7 4.2 4.5.3 1.1 42, 37, 32, 22, 14, 9, 7,1 5, 3, 2,.2.4 71.3 7.2 3.2 5.9 54.4 49. 44.5 3. 32.3 24.2 2, 21, 14,1 9, 7,2 5, 4, 2,95 2, 1, 95 4. 7. 73.. 7.4 4.2.9 57.5 54 5.4 4.5, 13,5 9, 7,2 5,4 4, 3, 2, 1,5 1, 1,1 2,3 24 3 4 5 4 5 9 ft JIB ft JIB ALL,5,9 3, 2, 5 ALL 4, 3, 2,4 1, RATED REDUCTIONS WITH JIB LENGTH ft ft 13 ft - ft JIB STOWED Reduce load lb Reduce load lb Reduce load lb Reduce load lb portland office: 53.23.11 seattle office: 2.74.4 - ft JIB ERECTED AT ft LENGTH Reduce load 2,3 lb Reduce load 2, lb Reduce load 1,9 lb Reduce load 1, lb
Load Rating Chart: Series 7 (3.71 m) Boom with ft (9. m) Jib/Fullspan Outrigger 24. ft (7.51 m) HEIGHT IN FEET 1 1 14 13 11 1 9 5 4 3 2 1 O M O E NGT L B 13 7 T E E F N I H O O O -1 O C/L 1 2 3 4 5 9 1 IN FEET O O O O 7 FULL-SPAN OUTRIGGER 24. FT. 7 ft ft JIB 5 O 4 O 4 O O 3 O O 2 O O 1 O 5 O O accessories or loads within 1 ft (3m) of live power lines Always level the crane with the level indicator located on the crane. Load Rating Chart: Series 7 (3.71 m) Boom with ft (9. m) Jib/Fullspan Outrigger 24. ft (7.51 m) SERIES 7 (3.71 M) WITH FT (9. M) JIB/FULL-SPAN OUTRIGGER 24. FT (7.51 M) (ft) 1 2 3 4 5 5 9 95 1 7.4 72.2 3.7 57 44.3 27.1 ft ft 13 ft 7 ft 72, 3, 54, 47, 3,5 29,5 22,,5 7. 73.5 7. 1..5 4. 4.7.3 1.9 3,, 24, 2,5 17,4 14, 11, 9, 7,4,3.5. 71.9 3.9 59.7.2 5..4 39. 33.1.1.7, 2,5 17, 14,,9 11,3 9,4 7,,5 5,3 4,3 3,5 2,5 2,. 77 74.2 71.3.4.4 2.2 5.9.3 51.5 47. 43.4 3. 33. 27.9 2.5 7.3 14, 13, 11, 1, 9,5,4 7,, 5,5 4,5 3, 3,5 2,4 1,9 1,5 1,1.5 77.5.3 73.1..5.9 3.3. 57. 51.9 4.7.4 41.9 3.1 34,,2 7, 7,2,,2 5,4 4, 4,2 3, 3,1 2, 2,5 1, 1,2 5 29 44 5 72 4 94 14 ft JIB 5 ALL 3, 3,3 2,9 2,5 2, 1, 1, LENGTH ft ft ft 13ft 7ft RATED REDUCTIONS WITH JIB ft JIB STOWED Reduce load 5 lb Reduce load 3 lb Reduce load 2 lb Reduce load lb Reduce load 1 lb ft JIB ERECTED Reduce load 1, lb Reduce load 1,4 lb Reduce load 1,3 lb Reduce load 1, lb Reduce load 1,2 lb portland office: 53.23.11 seattle office: 2.74.4
Load Rating Chart: Series 7 (3.71 m) Boom with ft (9. m) Jib/Midspan Outrigger 17.5 ft (5.33 m) HEIGHT IN FEET 1 1 14 13 11 1 9 5 4 3 2 1 T H N G FE I O L O EN M B T E 13 7 O -1 O C/L 1 2 3 4 5 O IN FEET O O O 1 O O 5 O O 4 O O 3 O O 2 O O 1 O 5 O O 7 MID-SPAN OUTRIGGER 17.5 ft 7 ft ft JIB accessories or loads within 1 ft (3m) of live power lines Always level the crane with the level indicator located on the crane. Load Rating Chart: Series 7 (3.71 m) Boom with ft (9. m) Jib/Midspan Outrigger 17.5 ft (5.33 m) SERIES 7 (3.71 M) WITH FT (9. M) JIB/MID-SPAN OUTRIGGER 17.5 FT (5.33 M) (ft) 1 2 3 4 5 7.4 72.2 3.7 57 44.1 27.4 ft ft 13 ft 7 ft 72, 3, 54, 47, 3,5 22,1 13,4 9,4 7. 73.5 7.7 1.4 54.9 4.4 4..3 1.2 3,, 23,5 1,4 1,1 7,3 5,2 3, 2, 2,2.5. 71.7 7.4 3.4 59.1 54.5 49.7 44.5 3. 32.2 24.2, 2,5,3 1, 7, 5, 4,2 3,1 2,2 1,5 5 4. 77 74.9 7. 4.3 1 57. 54 5.3 4.4 14, 13, 1, 7,9 5,9 4,4 3,3 2,4 1, 1,5.5 77.5.3 72.7.1 7.4 4.7 2 59.3 5.4,,2 7,, 4, 3,4 2,5 1, 1,2 ft JIB RATED REDUCTIONS WITH JIB ft JIB STOWED ft JIB ERECTED ALL LENGTH Reduce load 5 lb Reduce load 3 lb Reduce load 2 lb Reduce load lb Reduce load 1 lb Reduce load 1, lb Reduce load 1,4 lb Reduce load 1,3 lb Reduce load 1, lb Reduce load 1,2 lb portland office: 53.23.11 seattle office: 2.74.4