Section 9: Gearboxes: Series W

GEARBOXES Section : 9 Section 9: Gearboxes: Series W A modular designed aluminium worm box available in a vast range of sizes and ratios for cost effective solutions. 9 s with ratings from 0.09 to 7.5kW s from 5:1 to 300:1 helical Hollow bore or solid shaft versions Accepts standard IEC motors Modular design with multiple flange options to interchange aith other makes Geared Drives: Design Data Required Motorised (integral motor) or non-motorised? Shaft mounting or flange mounted? Type of driven machine Rotational speed of driven machine Power absorbed by driven machine (or required output torque) Hours/day duty & start/stop frequency > If motorised: electrical supply available any special motor features required (brake, clutch, flameproof etc.) > If non-motorised: type of prime mover, rotational speed of prime mover, power rating of prime mover, is an input shaft coupling required? If so, prime mover shaft dia. > If shaft mounted, machine shaft diameter/length > if shaft mounted, is an output shaft coupling required? > constant or variable over what range? Series W Page Procedure 319 Motorised 320 Dimensions - worm geared motor 326 Dimensions - motor input 327 Dimensions - options 328 Dimensions - Heli-worm 330 on-motorised selection 331 Dimensions - reducers 335 Mesh Data 336 Ordering Instructions 337 Codes 338 s 339 Installation & Maintenance 340 Visit www.fptgroup.com

SERIES W Vast range of sizes and ratios for cost effective solutions. > 11 s with ratings from 0.06 to 15kW > s from 5:1 to 5000:1 with helical or double worm combinations > Interchangeable dimensionally with other makes > Hollow bore or solid shaft versions > Accepts standard IEC motors The Mark of Engineering Excellence www.fptgroup.com

GeArboxes Section : 9 Series W Gearboxes : Motorised selection MOTORISED UITS SELECTIO PROCEDURE (a) From Table 1 select the Mechanical (Fm) applicable to the drive. If the unit is to be subjected to frequent stop/starts in excess of 10 times per day then multiply factor Fm by Fs from table 2. (b) Motor Power Refer to the selection tables on pages 320 to 325 and choose a motor power equal to or in excess of that required, if the motor power is not known then from the formula below determine the power requirements of the driven machine and select a motor power in excess of the calculated machine absorbed power. M 2 x n 2 P2 = 9550 P 2 = machine absorbed power (kw) M 2 = machine absorbed torque (m) n 2 = machine speed (rev/min) (c) Refer to the selection tables on page 320 to 325 and choose a motor power equal to or closest above that calculated in step (b). Then read down the column headed ominal Speed until a speed equal to or near to the required speed is found. On this line read across to the service factor column and check that the service factor exceeds the value from step (a). If the service factor is either lower or much higher than that required check the speeds at each side of the required speed to see if a more suitable unit and factor can be found. (d) s If the unit is to be fitted with an output shaft and an indirect drive attached to the shaft, calculate the overhung load value using the formula on page 339 and compare this value with the maximum allowable value given in column 5 of the selection tables. If the value exceeds the maximum allowed, then either re-design the indirect drive or select a larger unit capable of supporting the overhung load. (e) Shaft Mounted If the unit is to be shaft mounted determine the relevant machine shaft size from the dimension tables on page 326. arm dimensions can be found on page 329. SELECTIO EXAMPLE A series W shaft mounted gearbox is required to drive a variable density mixer, which absorbs 450 m at 36 rev/min and operates for up to 8 hours per day. The mixer stops and starts on average 4 times a day. Specify the shaft diameter required to fit the unit selected, a torque arm bracket is also required please specify the relevant product code. (a) From table 1, a variable density mixer is classed as a moderately loaded machine and when running for 8 hours per day has a service factor of 1.2. The machine stops and starts only 4 times a day therefore an additional stop/start factor is not required. (b) Motor Power To determine the required motor power use the absorbed torque and the machine shaft speed in the formula given. Then use the next largest standard motor power above this. Therefore the absorbed Power P 2 = 450 x 36 = 1.7 kw 9550 (c) The nearest standard motor power above 1.7 kw is 2.2 kw therefore we go to the 2.2kW geared motor selections on page 324. Reading down the column headed nominal output speed it is found that there are 2 units listed at 36 rev/min, at the first one of these read across to maximum service factor column, it can be seen that the unit size 747A0645 has a service factor of 1.4. This exceeds the 1.2 factor required and therefore is suitable for the application. TABLE 1 - MECHAICAL SERVICE FACTOR (Fm) (d) s The gearbox is to be shaft mounted therefore there are no overhung loads present. (e) Shaft Mounted The unit is to be shaft mounted, referring to page 326 we see that the hub bore size is 42 mm. From page 329 the torque arm bracket to suit the size 747 unit selected has a product code of 748A9600. Types of Driven Machine Operational Hours Under 3 3 to 10 Over 10 Uniform s Agitators and Mixers liquid or semi-liquid Blowers centrifugal Bottling Machines Conveyors and Elevators uniformly loaded Cookers 0.80 1.00 1.20 Laundry Washing Machines non-reversing Line Shafts Pumps centrifugal and gear Wire Drawing Machines Moderate Shock s Agitators and Mixers variable density Conveyors not uniformly loaded Cranes travel motion and hoisting Drawbench Feeders pulsating load Hoists Kilns 1.00 1.20 1.40 Laundry Tumblers Lifts Pumps reciprocating with 3 or more cylinders Pump and Paper Making Machinery Rubber Mixers and Calendars Screens rotary Textile Machinery Heavy Shock s Brick Presses Briquetting Machines Conveyors reciprocating and shaker Crushers Feeders reciprocating Hammer Mills Pumps reciprocating, 1 or 2 cylinders Rubber Masticators Screens vibrating 1.50 1.75 2.00 For High Inertia Applications, consult your authorised distributor for verification of selection TABLE 2 - STARTIG FACTOR (Fs) Start/stops per hour Up to 5 6-20 21-30 31-50 51-80 81-100 Uniform 1.00 1.05 1.10 1.15 1.20 1.25 Moderate Shock 1.05 1.10 1.20 1.25 1.35 1.40 Heavy Shock 1.20 1.25 1.30 1.40 1.45 1.50 FE01/14 : Drive Design & Maintenance Manual 319

Section : 9 Roller Chain Drive Series W Gearboxes : Motorised selection GEARBOXES Bold print indicates 6 pole motor, italics indicates 2 pole motor, all others are 4 pole motors. 0.09 KW Motor ominal m 551 1.4 8.65 741A0143 474 367 2.0 5.50 740A0243 399 367 2.0 6.39 741A0243 542 276 2.6 4.73 740A0343 439 276 2.7 4.91 741A0343 597 264 2.8 6.36 741A0114 597 184 3.7 3.16 740A0443 503 184 3.8 3.43 741A0443 683 180 4.1 4.93 741A0115 692 180 4.2 9.63 742A0115 1331 176 4.2 2.64 740A0214 399 176 4.2 4.34 741A0214 683 138 4.9 2.47 741A0543 752 138 4.7 2.56 740A0543 553 132 5.4 2.27 740A0314 439 132 5.3 3.38 741A0314 752 120 6.0 3.37 741A0215 792 120 6.1 7.23 742A0215 1524 110 5.5 2.28 740A0643 633 110 5.8 2.78 741A0643 810 92 6.3 2.11 740A0743 633 92 6.7 2.26 741A0743 861 90 7.6 2.62 741A0315 871 90 7.9 5.56 742A0315 1677 88 7.7 1.52 740A0414 503 88 7.5 2.40 741A0414 861 69 8.2 1.70 741A0843 948 69 7.7 1.75 740A0843 697 66 9.8 1.23 740A0514 553 66 9.5 1.90 741A0514 948 60 10.6 1.89 741A0415 997 60 11.2 4.03 742A0415 1920 55 9.1 1.20 740A0943 751 55 9.7 1.35 741A0943 1021 55 10.6 2.83 742A0943 1964 53 11.6 1.09 740A0614 633 53 11.1 1.90 741A0614 1021 46 10.3 0.96 740A1043 798 46 10.9 1.11 741A1043 1085 46 12.2 2.31 742A1043 2104 45 13.4 1.50 741A0515 1098 45 14.3 3.08 742A0515 2113 44 13.1 1.01 740A0714 633 44 12.7 1.58 741A0714 1085 36 15.3 1.51 741A0615 1183 36 17.2 2.51 742A0615 2276 34 13.0 0.85 741A1143 1194 34 14.7 1.70 742A1143 2384 33 16.2 0.84 740A0814 697 33 15.4 1.18 741A0814 1194 30 17.5 1.21 741A0715 1257 30 18.9 2.60 742A0715 2419 28 16.9 1.37 742A1243 2664 26 18.9 0.58 740A0914 751 26 17.9 0.95 741A0914 1286 26 20.2 1.94 742A0914 2475 23 21.0 0.96 741A0815 1383 23 23.7 1.91 742A0815 2662 23 24.1 3.41 743A0815 3654 22 21.5 0.46 740A1014 798 22 19.9 0.81 741A1014 1367 22 22.7 1.59 742A1014 2630 18 24.4 0.74 741A0915 1490 18 27.2 1.55 742A0915 2868 18 28.2 2.74 743A0915 3936 17 22.9 0.57 741A1114 1540 17 27.1 1.22 742A1114 2895 15 31.0 1.27 742A1015 3047 15 31.5 2.29 743A1015 4183 13 30.6 0.95 742A1214 3118 12 40.1 0.80 741A2015 1706 12 47.3 1.21 742A2015 3283 11 36.7 0.96 742A1115 3354 11 37.4 1.82 743A1115 4604 10 46.4 0.63 741A2115 1813 ominal m 10 51.6 1.32 742A2115 3488 9 41.1 0.78 742A1215 3490 9 42.0 1.34 743A1215 4840 8 55.0 0.48 741A2215 1820 8 61.9 0.99 742A2215 3490 8 63.0 1.83 743A2215 4840 6 63.0 0.39 741A2315 1820 6 71.6 0.79 742A2315 3490 6 73.1 1.51 743A2315 4840 5 79.1 0.68 742A2415 3490 5 80.8 1.22 743A2415 4840 4 94.0 0.48 742A2515 3490 4 94.0 0.86 743A2515 4840 3 103.1 0.40 742A2615 3490 3 106.0 0.70 743A2615 4840 0.12 KW Motor ominal m 551 1.9 6.49 741A0147 474 367 2.7 4.12 740A0247 399 367 2.7 4.79 741A0247 542 276 3.6 4.99 741A0148 597 276 3.7 9.21 742A0148 1149 276 3.5 3.55 740A0347 439 276 3.5 3.68 741A0347 597 184 5.3 3.41 741A0248 683 184 5.4 7.39 742A0248 1315 184 4.9 2.37 740A0447 503 184 5.1 2.58 741A0447 683 181 5.4 3.72 741A0113 692 181 5.5 7.27 742A0113 1331 138 6.8 2.65 741A0348 752 138 7.1 5.67 742A0348 1447 138 6.5 1.85 741A0547 752 138 6.2 1.92 740A0547 553 121 7.9 2.54 741A0213 792 121 8.1 5.46 742A0213 1524 110 7.4 1.71 740A0647 633 110 7.7 2.08 741A0647 810 92 9.6 1.88 741A0448 861 92 10.2 3.92 742A0448 1657 92 8.4 1.58 740A0747 633 92 8.9 1.70 741A0747 861 91 10.1 1.98 741A0313 871 91 10.5 4.19 742A0313 1677 69 12.1 1.49 741A0548 948 69 13.0 3.02 742A0548 1824 69 11.0 1.28 741A0847 948 69 10.3 1.31 740A0847 697 60 14.1 1.43 741A0413 997 60 14.8 3.04 742A0413 1920 55 14.1 1.49 741A0648 1021 55 15.6 2.45 742A0648 1964 55 12.1 0.90 740A0947 751 55 12.9 1.01 741A0947 1021 55 14.2 2.13 742A0947 1964 46 16.2 1.24 741A0748 1085 46 17.4 2.59 742A0748 2087 46 13.7 0.72 740A1047 798 46 14.5 0.83 741A1047 1085 46 16.2 1.73 742A1047 2104 45 17.7 1.13 741A0513 1098 45 19.0 2.32 742A0513 2113 36 20.3 1.14 741A0613 1183 36 22.8 1.89 742A0613 2276 35 19.6 0.92 741A0848 1194 35 21.6 1.90 742A0848 2298 35 22.3 3.42 743A0848 3153 34 17.3 0.64 741A1147 1194 34 19.6 1.28 742A1147 2384 30 23.2 0.91 741A0713 1257 30 25.1 1.96 742A0713 2419 28 22.8 0.75 741A0948 1286 28 25.8 1.52 742A0948 2475 ominal 0.18kW MOTOR ominal m m 28 26.2 2.80 743A0948 3397 28 22.5 1.03 742A1247 2664 23 28.9 1.25 742A1048 2630 23 29.4 2.32 743A1048 3610 23 27.9 0.72 741A0813 1383 23 31.4 1.44 742A0813 2662 23 31.9 2.57 743A0813 3654 18 38.0 0.77 741A2048 1200 18 43.0 1.15 742A2048 2833 18 32.3 0.56 741A0913 1490 18 36.1 1.17 742A0913 2868 18 37.4 2.07 743A0913 3936 17 34.6 0.96 742A1148 2895 17 35.2 1.85 743A1148 3973 15 42.6 0.62 741A2148 1621 15 47.1 1.24 742A2148 3011 15 41.0 0.96 742A1013 3047 15 41.8 1.73 743A1013 4183 14 39.0 0.75 742A1248 3118 14 40.7 1.36 743A1248 4280 12 53.2 0.61 741A2013 1706 12 62.7 0.91 742A2013 3283 12 51.8 0.45 741A2248 1785 12 57.8 0.92 742A2248 3314 12 58.8 1.67 743A2248 4548 11 48.6 0.72 742A1113 3354 11 49.6 1.37 743A1113 4604 10 61.5 0.48 741A2113 1813 10 68.4 1.00 742A2113 3488 9 58.5 0.36 741A2348 1880 9 67.3 0.73 742A2348 3490 9 68.5 1.33 743A2348 4840 9 54.5 0.59 742A1213 3490 9 55.7 1.01 743A1213 4840 8 74.7 0.62 742A2448 3490 8 82.2 1.01 743A2448 4840 8 72.9 0.36 741A2213 1820 8 82.1 0.75 742A2213 3490 8 83.6 1.38 743A2213 4840 6 83.6 0.29 741A2313 1820 6 95.0 0.59 742A2313 3490 6 96.9 1.14 743A2313 4840 6 87.7 0.46 742A2548 3490 6 89.7 0.84 743A2548 4840 5 104.8 0.51 742A2413 3490 5 107.1 0.92 743A2413 4840 5 97.2 0.38 742A2648 3490 5 99.7 0.66 743A2648 4840 4 124.6 0.37 742A2513 3490 4 124.6 0.65 743A2513 4840 3 136.8 0.30 742A2613 3490 3 140.6 0.53 743A2613 4840 554 2.8 4.35 741A0101 474 554 2.8 8.60 742A0101 912 369 4.1 3.22 741A0201 542 369 4.2 6.76 742A0201 1044 277 5.3 2.47 741A0301 597 277 5.5 5.32 742A0301 1149 276 5.4 3.33 741A0102 597 276 5.6 6.14 742A0102 1149 185 7.6 1.73 741A0401 683 185 7.8 3.97 742A0401 1315 184 8.0 2.27 741A0202 683 184 8.1 4.93 742A0202 1315 178 8.4 4.77 742A0105 1331 178 8.5 8.83 743A0105 1827 139 9.7 1.24 741A0501 752 139 10.2 2.85 742A0501 1447 138 10.2 1.77 741A0302 752 138 10.6 3.78 742A0302 1447 119 12.3 3.58 742A0205 1524 320

GEARBOXES Series W Gearboxes : Motorised selection Roller Chain Drive Section : 9 ominal m 119 12.5 6.75 743A0205 2091 111 11.5 1.40 741A0601 810 111 12.3 2.29 742A0601 1559 92 13.2 1.14 741A0701 861 92 14.2 2.41 742A0701 1657 92 14.4 1.26 741A0402 861 92 15.3 2.62 742A0402 1657 89 16.0 2.75 742A0305 1677 89 16.2 5.18 743A0305 2302 69 16.4 0.86 741A0801 948 69 17.9 1.74 742A0801 1824 69 18.1 3.26 743A0801 2503 69 18.2 0.99 741A0502 948 69 19.4 2.01 742A0502 1824 59 22.6 2.00 742A0405 1920 59 22.9 3.68 743A0405 2635 55 19.2 0.68 741A0901 1021 55 21.1 1.43 742A0901 1964 55 21.4 2.48 743A0901 2696 55 21.2 1.00 741A0602 1021 55 23.4 1.63 742A0602 1964 46 24.2 1.16 742A1001 2104 46 24.6 2.04 743A1001 2865 46 24.3 0.83 741A0702 1085 46 26.2 1.73 742A0702 2087 45 29.0 1.52 742A0505 2113 45 29.4 2.63 743A0505 2900 36 34.8 1.24 742A0605 2276 36 35.3 2.13 743A0605 3124 35 29.3 0.86 742A1101 2384 35 30.3 1.49 743A1101 3153 35 29.4 0.62 741A0802 1194 35 32.4 1.27 742A0802 2298 35 33.4 2.28 743A0802 3153 30 38.3 1.29 742A0705 2419 30 39.4 2.29 743A0705 3320 28 33.5 0.69 742A1201 2664 28 34.8 1.16 743A1201 3397 28 34.3 0.50 741A0902 1286 28 38.6 1.01 742A0902 2475 28 39.2 1.87 743A0902 3397 23 43.4 0.84 742A1002 2630 23 44.1 1.55 743A1002 3610 22 47.9 0.94 742A0805 2662 22 48.7 1.69 743A0805 3654 18 57.0 0.51 741A2002 1200 18 64.5 0.77 742A2002 2833 18 57.0 1.36 743A0905 3936 18 61.8 3.56 745A0905 6073 17 51.8 0.64 742A1102 2895 17 52.8 1.24 743A1102 3973 15 63.9 0.41 741A2102 1621 15 70.6 0.83 742A2102 3011 15 63.7 1.13 743A1005 4183 15 70.7 2.98 745A1005 6453 14 58.6 0.50 742A1202 3118 14 61.0 0.91 743A1202 4280 12 95.6 0.60 742A2005 3283 12 95.6 1.09 743A2005 4506 12 77.7 0.30 741A2202 1785 12 86.7 0.62 742A2202 3314 12 88.2 1.12 743A2202 4548 11 75.7 0.90 743A1105 4604 11 85.0 2.36 745A1105 7103 10 104.3 0.66 742A2105 3488 10 106.0 1.26 743A2105 4788 9 87.8 0.24 741A2302 1880 9 100.9 0.49 742A2302 3490 9 102.8 0.89 743A2302 4840 9 85.0 0.66 743A1205 4840 9 96.6 1.97 745A1205 7380 8 112.1 0.42 742A2402 3490 8 123.3 0.68 743A2402 4840 7 125.2 0.49 742A2205 3490 7 127.5 0.91 743A2205 4840 7 132.1 1.64 744A2205 6270 6 147.8 0.75 743A2305 4840 6 153.6 1.32 744A2305 6270 ominal m 6 159.3 1.87 745A2305 7380 6 131.5 0.31 742A2502 3490 6 134.5 0.56 743A2502 4840 5 163.4 0.60 743A2405 4840 5 170.4 1.09 744A2405 6270 5 180.8 1.55 745A2405 7380 5 145.7 0.25 742A2602 3490 5 149.5 0.44 743A2602 4840 4 190.1 0.43 743A2505 4840 4 199.3 0.81 744A2505 6270 4 213.2 1.12 745A2505 7380 3 214.4 0.35 743A2605 4840 3 220.2 0.65 744A2605 6270 3 237.6 0.94 745A2605 7380 0.25W MOTOR ominal m 552 3.9 3.12 741A0103 474 552 3.9 6.17 742A0103 912 368 5.7 2.31 741A0203 542 368 5.8 4.85 742A0203 1044 276 7.4 1.77 741A0303 597 276 7.6 3.81 742A0303 1149 272 7.8 4.36 742A0106 1149 272 7.8 7.94 743A0106 1577 184 10.5 1.24 741A0403 683 184 10.9 2.85 742A0403 1315 181 11.5 3.50 742A0206 1315 181 11.6 6.13 743A0206 1805 180 11.5 3.47 742A0107 1331 180 11.7 6.43 743A0107 1827 138 13.5 0.89 741A0503 752 138 14.2 2.05 742A0503 1447 136 14.9 2.69 742A0306 1447 136 15.1 4.77 743A0306 1987 120 16.9 2.61 742A0207 1524 120 17.1 4.91 743A0207 2091 110 16.0 1.00 741A0603 810 110 17.1 1.64 742A0603 1559 92 18.4 0.82 741A0703 861 92 19.7 1.73 742A0703 1657 91 21.6 1.86 742A0406 1657 91 21.6 3.43 743A0406 2274 90 22.0 2.00 742A0307 1677 90 22.3 3.77 743A0307 2302 69 22.8 0.62 741A0803 948 69 24.9 1.25 742A0803 1824 69 25.3 2.34 743A0803 2503 68 27.4 1.43 742A0506 1824 68 27.7 2.64 743A0506 2503 60 31.0 1.45 742A0407 1920 60 31.4 2.68 743A0407 2635 55 26.8 0.49 741A0903 1021 55 29.4 1.03 742A0903 1964 55 29.9 1.78 743A0903 2696 54 32.9 1.16 742A0606 1964 54 33.4 2.10 743A0606 2696 46 33.7 0.83 742A1003 2104 46 34.3 1.46 743A1003 2865 45 36.9 1.23 742A0706 2087 45 37.9 2.22 743A0706 2865 45 39.8 1.11 742A0507 2113 45 40.3 1.91 743A0507 2900 36 47.8 0.91 742A0607 2276 36 48.4 1.55 743A0607 3124 35 40.8 0.62 742A1103 2384 35 42.2 1.07 743A1103 3153 34 45.7 0.90 742A0806 2298 34 47.1 1.62 743A0806 3153 34 49.2 2.95 744A0806 4122 30 52.5 0.94 742A0707 2419 30 54.1 1.67 743A0707 3320 28 46.7 0.50 742A1203 2664 ominal m 28 48.5 0.83 743A1203 3397 27 55.3 1.33 743A0906 3397 27 57.9 2.34 744A0906 4440 27 60.6 3.47 745A0906 5241 23 62.2 1.10 743A1006 3610 23 65.3 2.00 744A1006 4719 23 68.5 2.93 745A1006 5569 23 65.8 0.69 742A0807 2662 23 66.9 1.23 743A0807 3654 18 90.8 0.54 742A2006 2833 18 90.8 1.01 743A2006 3889 18 78.3 0.99 743A0907 3936 18 84.9 2.60 745A0907 6073 17 74.4 0.88 743A1106 3973 17 80.1 1.53 744A1106 5193 17 84.3 2.26 745A1106 6130 15 99.5 0.59 742A2106 3011 15 101.1 1.07 743A2106 4132 15 87.6 0.83 743A1007 4183 15 97.1 2.17 745A1007 6453 14 86.0 0.64 743A1206 4280 14 89.5 1.32 744A1206 5595 14 96.6 1.87 745A1206 6603 12 131.3 0.44 742A2007 3283 12 131.3 0.80 743A2007 4506 11 122.2 0.44 742A2206 3314 11 124.3 0.79 743A2206 4548 11 128.5 1.44 744A2206 5945 11 104.0 0.66 743A1107 4604 11 116.7 1.72 745A1107 7103 10 143.3 0.48 742A2107 3488 10 145.6 0.92 743A2107 4788 9 144.8 0.63 743A2306 4840 9 147.5 1.18 744A2306 6270 9 155.4 1.61 745A2306 7380 9 116.7 0.48 743A1207 4840 9 132.6 1.44 745A1207 7380 8 173.8 0.48 743A2406 4840 8 167.5 0.96 744A2406 6270 8 177.0 1.36 745A2406 7380 8 171.9 0.36 742A2207 3490 8 175.1 0.66 743A2207 4840 8 181.5 1.20 744A2207 6270 6 202.9 0.55 743A2307 4840 6 210.9 0.96 744A2307 6270 6 218.9 1.36 745A2307 7380 6 189.6 0.40 743A2506 4840 6 198.0 0.70 744A2506 6270 6 206.4 1.05 745A2506 7380 5 224.4 0.44 743A2407 4840 5 234.0 0.80 744A2407 6270 5 248.3 1.13 745A2407 7380 5 210.7 0.31 743A2606 4840 5 221.2 0.58 744A2606 6270 5 237.0 0.89 745A2606 7380 4 261.0 0.31 743A2507 4840 4 273.8 0.59 744A2507 6270 4 292.9 0.82 745A2507 7380 3 294.5 0.26 743A2607 4840 3 302.4 0.47 744A2607 6270 3 326.3 0.69 745A2607 7380 FE01/14 : Drive Design & Maintenance Manual 321

Section : 9 Roller Chain Drive Series W Gearboxes : Motorised selection GEARBOXES Bold print indicates 6 pole motor, italics indicates 2 pole motor, all others are 4 pole motors. 0.37 KW Motor 322 ominal m 560 5.7 4.23 742A0109 912 560 5.8 7.84 743A0109 1251 373 8.4 3.33 742A0209 1044 373 8.5 6.11 743A0209 1433 280 11.1 2.62 742A0309 1149 280 11.1 4.87 743A0309 1577 273 11.5 2.96 742A0108 1149 273 11.5 5.39 743A0108 1577 187 15.9 1.95 742A0409 1315 187 16.1 3.55 743A0409 1805 182 16.9 2.37 742A0208 1315 182 17.1 4.16 743A0208 1805 182 17.1 4.39 743A0112 1827 140 20.7 1.41 742A0509 1447 140 20.7 2.57 743A0509 1987 137 22.0 1.82 742A0308 1447 137 22.3 3.24 743A0308 1987 121 25.1 3.36 743A0212 2091 121 25.3 5.96 744A0212 2735 112 24.9 1.13 742A0609 1559 112 25.2 2.03 743A0609 2140 93 28.8 1.19 742A0709 1657 93 28.8 2.23 743A0709 2274 91 31.9 1.26 742A0408 1657 91 31.9 2.33 743A0408 2274 91 32.6 2.58 743A0312 2302 91 33.0 4.64 744A0312 3009 70 36.4 0.86 742A0809 1824 70 36.9 1.61 743A0809 2503 70 37.9 2.86 744A0809 3272 68 40.4 0.97 742A0508 1824 68 40.9 1.79 743A0508 2503 61 46.0 1.83 743A0412 2635 61 47.2 3.29 744A0412 3444 56 43.5 1.22 743A0909 2696 56 44.8 2.24 744A0909 3524 56 46.7 3.22 745A0909 4160 55 48.5 0.79 742A0608 1964 55 49.2 1.43 743A0608 2696 47 50.0 1.01 743A1009 2865 47 51.5 1.85 744A1009 3745 47 53.8 2.70 745A1009 4421 46 54.4 0.83 742A0708 2087 46 59.0 1.31 743A0512 2900 46 55.9 1.51 743A0708 2865 46 59.8 2.48 744A0512 3791 46 61.4 3.84 745A0512 4474 36 70.9 1.06 743A0612 3124 36 72.8 1.89 744A0612 4084 36 74.8 2.88 745A0612 4820 35 61.6 0.74 743A1109 3153 35 63.6 1.34 744A1109 4122 35 66.6 1.96 745A1109 4865 34 67.3 0.61 742A0808 2298 34 69.4 1.10 743A0808 3153 30 79.2 1.14 743A0712 3320 30 81.6 2.15 744A0712 4339 30 85.0 3.06 745A0712 5122 28 70.7 0.57 743A1209 3397 28 73.2 1.02 744A1209 4440 28 77.0 1.56 745A1209 5241 27 81.6 0.90 743A0908 3397 27 89.3 2.36 745A0908 5241 23 91.6 0.75 743A1008 3610 23 97.9 0.84 743A0812 3654 23 101.0 1.59 744A0812 4776 23 101.0 1.99 745A1008 5569 23 105.6 2.28 745A0812 5637 23 110.3 3.72 746A0812 6328 18 134.0 0.37 742A2008 2833 18 134.0 0.68 743A2008 3889 18 118.4 1.23 744A0912 5145 18 124.3 1.78 745A0912 6073 18 132.0 2.96 746A0912 6719 17 109.8 0.60 743A1108 3973 ominal m 0.55 KW Motor 17 124.3 1.53 745A1108 6130 15 146.8 0.40 742A2108 3011 15 149.1 0.73 743A2108 4132 15 135.1 1.03 744A1012 5467 15 142.1 1.48 745A1012 6453 15 149.1 2.35 746A1012 7140 14 126.9 0.44 743A1208 4280 14 142.4 1.27 745A1208 6603 12 192.2 0.55 743A2012 4506 12 198.0 0.99 744A2012 5810 12 203.9 1.50 745A2012 6952 11 180.2 0.30 742A2208 3314 11 183.3 0.54 743A2208 4548 11 161.5 0.80 744A1112 6018 11 189.5 0.98 744A2208 5945 11 170.9 1.18 745A1112 7103 11 183.3 1.72 746A1112 7859 10 213.2 0.63 743A2112 4788 10 216.7 1.11 744A2112 6259 10 227.2 1.59 745A2112 7380 9 213.6 0.43 743A2308 4840 9 217.4 0.80 744A2308 6270 9 194.2 0.98 745A1212 7380 9 229.1 1.10 745A2308 7380 9 209.7 1.34 746A1212 8180 8 256.3 0.33 743A2408 4840 8 256.3 0.45 743A2212 4840 8 247.0 0.65 744A2408 6270 8 265.6 0.82 744A2212 6270 8 260.9 0.92 745A2408 7380 8 279.6 1.20 745A2212 7380 8 293.6 1.94 746A2212 8180 6 308.7 0.66 744A2312 6270 6 320.3 0.93 745A2312 7380 6 343.6 1.53 746A2312 8180 6 279.6 0.27 743A2508 4840 6 292.0 0.47 744A2508 6270 6 304.4 0.71 745A2508 7380 5 342.5 0.55 744A2412 6270 5 363.4 0.78 745A2412 7380 5 384.4 1.23 746A2412 8180 5 310.6 0.21 743A2608 4840 5 326.2 0.40 744A2608 6270 5 349.5 0.61 745A2608 7380 4 400.7 0.40 744A2512 6270 4 428.7 0.56 745A2512 7380 4 466.0 0.92 746A2512 8180 3 477.6 0.47 745A2612 7380 3 524.2 0.74 746A2612 8180 ominal m 556 8.5 2.83 742A0110 912 556 8.6 5.24 743A0110 1251 371 12.6 2.23 742A0210 1044 371 12.8 4.08 743A0210 1433 282 16.6 3.75 743A0116 1577 278 16.6 1.75 742A0310 1149 278 16.6 3.25 743A0310 1577 188 24.6 2.89 743A0216 1805 188 24.6 5.21 744A0216 2360 185 23.8 1.31 742A0410 1315 185 24.1 2.37 743A0410 1805 182 25.4 2.96 743A0117 1827 141 32.0 2.25 743A0316 1987 141 32.4 4.02 744A0316 2597 139 31.0 0.94 742A0510 1447 139 31.0 1.72 743A0510 1987 121 37.2 2.26 743A0217 2091 121 37.7 4.01 744A0217 2735 111 37.3 0.76 742A0610 1559 111 37.8 1.35 743A0610 2140 94 45.8 1.62 743A0416 2274 94 46.4 3.02 744A0416 2973 ominal m 93 43.1 0.79 742A0710 1657 93 43.1 1.49 743A0710 2274 91 48.5 1.74 743A0317 2302 91 49.1 3.12 744A0317 3009 71 58.9 1.25 743A0516 2503 71 60.4 2.24 744A0516 3272 71 61.1 3.44 745A0516 3862 70 54.4 0.57 742A0810 1824 70 55.2 1.07 743A0810 2503 70 56.7 1.91 744A0810 3272 61 68.4 1.23 743A0417 2635 61 70.1 2.22 744A0417 3444 56 70.8 0.99 743A0616 2696 56 72.7 1.79 744A0616 3524 56 74.5 2.69 745A0616 4160 56 65.2 0.82 743A0910 2696 56 67.1 1.50 744A0910 3524 56 69.9 2.15 745A0910 4160 47 80.5 1.05 743A0716 2865 47 82.7 1.94 744A0716 3745 47 84.9 2.71 745A0716 4421 46 74.8 0.67 743A1010 2865 46 77.1 1.24 744A1010 3745 46 80.5 1.81 745A1010 4421 46 87.7 0.88 743A0517 2900 46 88.9 1.67 744A0517 3791 46 91.2 2.58 745A0517 4474 36 105.3 0.72 743A0617 3124 36 108.2 1.27 744A0617 4084 36 111.1 1.94 745A0617 4820 35 99.8 0.77 743A0816 3153 35 104.3 1.40 744A0816 4122 35 107.3 2.06 745A0816 4865 35 111.8 3.23 746A0816 5383 35 92.2 0.49 743A1110 3153 35 95.2 0.90 744A1110 4122 35 99.8 1.31 745A1110 4865 30 117.8 0.77 743A0717 3320 30 121.2 1.45 744A0717 4339 30 126.4 2.06 745A0717 5122 28 122.9 1.10 744A0916 4440 28 128.5 1.64 745A0916 5241 28 134.1 2.54 746A0916 5799 28 105.8 0.38 743A1210 3397 28 109.6 0.68 744A1210 4440 28 115.3 1.05 745A1210 5241 24 138.6 0.94 744A1016 4719 24 145.3 1.38 745A1016 5569 24 154.2 2.08 746A1016 6163 23 145.5 0.57 743A0817 3654 23 150.1 1.07 744A0817 4776 23 157.0 1.53 745A0817 5637 23 163.9 2.51 746A0817 6328 19 192.8 0.48 743A2016 3889 19 198.4 0.83 744A2016 5083 19 204.0 1.26 745A2016 6000 18 176.1 0.83 744A0917 5145 18 184.7 1.20 745A0917 6073 18 196.3 1.99 746A0917 6719 18 169.9 0.72 744A1116 5193 18 178.8 1.07 745A1116 6130 18 187.8 1.52 746A1116 6783 16 214.6 0.51 743A2116 4132 16 217.9 0.92 744A2116 5300 16 228.0 1.32 745A2116 6375 15 200.9 0.69 744A1017 5467 15 211.3 1.00 745A1017 6453 15 221.7 1.58 746A1017 7140 14 204.9 0.88 745A1216 6603 14 219.8 1.23 746A1216 7306 12 285.7 0.37 743A2017 4506 12 294.4 0.67 744A2017 5810 12 303.0 1.01 745A2017 6952 12 263.7 0.38 743A2216 4548 12 272.7 0.68 744A2216 5945 12 281.6 1.00 745A2216 7017 12 295.0 1.63 746A2216 7764 11 240.1 0.54 744A1117 6018 11 254.0 0.79 745A1117 7103

GEARBOXES Series W Gearboxes : Motorised selection Roller Chain Drive Section : 9 ominal ominal m m 11 272.4 1.16 746A1117 7859 10 316.9 0.42 743A2117 4788 10 322.1 0.75 744A2117 6259 10 337.7 1.07 745A2117 7380 9 312.9 0.56 744A2316 6270 9 329.7 0.76 745A2316 7380 9 352.0 1.28 746A2316 8180 9 288.6 0.66 745A1217 7380 9 311.7 0.90 746A1217 8180 8 355.4 0.46 744A2416 6270 8 375.5 0.64 745A2416 7380 8 395.6 1.02 746A2416 8180 8 381.0 0.31 743A2217 4840 8 394.8 0.55 744A2217 6270 8 415.6 0.81 745A2217 7380 8 436.4 1.30 746A2217 8180 6 458.9 0.45 744A2317 6270 6 476.2 0.63 745A2317 7380 6 510.8 1.03 746A2317 8180 6 420.2 0.33 744A2516 6270 6 438.1 0.50 745A2516 7380 6 473.8 0.78 746A2516 8180 5 509.1 0.37 744A2417 6270 5 540.3 0.52 745A2417 7380 5 571.4 0.83 746A2417 8180 5 502.9 0.42 745A2616 7380 5 547.6 0.64 746A2616 8180 4 595.7 0.27 744A2517 6270 4 637.2 0.38 745A2517 7380 4 692.6 0.62 746A2517 8180 3 710.0 0.32 745A2617 7380 3 779.2 0.50 746A2617 8180 0.75KW Motor 558 11.7 3.86 743A0119 1251 372 17.3 3.01 743A0219 1433 372 17.3 5.37 744A0219 1873 282 22.6 2.75 743A0118 1577 279 22.6 2.40 743A0319 1577 279 22.9 4.25 744A0319 2061 188 33.5 2.12 743A0218 1805 188 33.5 3.82 744A0218 2360 186 32.7 1.75 743A0419 1805 186 33.1 3.12 744A0419 2359 141 43.7 1.65 743A0318 1987 141 44.2 2.95 744A0318 2597 140 42.1 1.26 743A0519 1987 140 43.1 2.32 744A0519 2597 140 43.7 3.67 745A0519 3065 123 51.1 4.21 745A0223 3227 123 51.7 6.58 746A0223 3570 112 51.4 1.00 743A0619 2140 112 52.6 1.75 744A0619 2797 112 53.3 2.82 745A0619 3302 94 62.5 1.19 743A0418 2274 94 63.3 2.22 744A0418 2973 93 58.5 1.10 743A0719 2274 93 60.1 2.00 744A0719 2973 93 61.6 2.76 745A0719 3509 93 66.6 3.46 745A0323 3551 93 67.4 5.50 746A0323 3929 71 80.3 0.91 743A0518 2503 71 82.3 1.65 744A0518 3272 71 83.3 2.53 745A0518 3862 70 75.0 0.79 743A0819 2503 70 77.0 1.41 744A0819 3272 70 79.1 2.09 745A0819 3862 70 81.1 3.39 746A0819 4273 62 95.3 2.47 745A0423 4065 62 97.6 4.31 746A0423 4498 56 96.5 0.73 743A0618 2696 56 99.1 1.32 744A0618 3524 ominal m 56 101.6 1.97 745A0618 4160 56 91.1 1.10 744A0919 3524 56 95.0 1.58 745A0919 4160 56 97.6 2.72 746A0919 4603 47 109.7 0.77 743A0718 2865 47 112.8 1.42 744A0718 3745 47 115.8 1.99 745A0718 4421 47 104.8 0.91 744A1019 3745 47 109.4 1.33 745A1019 4421 47 114.0 2.15 746A1019 4891 46 122.4 1.93 745A0523 4474 46 125.5 3.11 746A0523 4951 37 149.1 1.45 745A0623 4820 37 152.9 2.42 746A0623 5333 35 136.1 0.56 743A0818 3153 35 142.2 1.02 744A0818 4122 35 146.3 1.51 745A0818 4865 35 152.4 2.37 746A0818 5383 35 129.4 0.66 744A1119 4122 35 135.6 0.96 745A1119 4865 35 141.7 1.59 746A1119 5383 31 169.6 1.54 745A0723 5122 31 174.2 2.65 746A0723 5667 28 167.6 0.81 744A0918 4440 28 175.3 1.20 745A0918 5241 28 182.9 1.86 746A0918 5799 28 156.6 0.77 745A1219 5241 28 166.9 1.20 746A1219 5799 24 189.0 0.69 744A1018 4719 24 198.1 1.01 745A1018 5569 24 210.3 1.53 746A1018 6163 23 210.6 1.14 745A0823 5637 23 219.9 1.87 746A0823 6238 23 229.2 3.32 747A0823 7882 19 262.9 0.35 743A2018 3889 19 270.5 0.61 744A2018 5083 19 278.1 0.92 745A2018 6000 19 247.8 0.89 745A0923 6073 19 263.3 1.49 746A0923 6719 19 274.9 2.73 747A0923 8491 18 231.6 0.53 744A1118 5193 18 243.8 0.78 745A1118 6130 18 256.0 1.12 746A1118 6783 16 292.6 0.37 743A2118 4132 16 297.2 0.68 744A2118 5300 16 310.9 0.97 745A2118 6375 15 297.4 1.18 746A1023 7140 15 315.9 2.16 747A1023 9023 15 327.9 0.94 745A2023 6453 15 337.3 1.57 746A2023 7140 14 279.4 0.65 745A1218 6603 14 299.7 0.91 746A1218 7306 13 365.4 0.99 745A2123 6952 13 382.3 1.71 746A2123 7859 12 359.6 0.28 743A2218 4548 12 371.8 0.50 744A2218 5945 12 384.0 0.73 745A2218 7017 12 402.3 1.20 746A2218 7764 12 390.3 1.46 747A1123 9931 12 396.5 2.17 749A1123 12989 10 449.7 0.75 745A2223 7380 10 472.2 1.21 746A2223 8180 10 464.7 1.59 747A2223 10320 9 426.7 0.41 744A2318 6270 9 449.6 0.56 745A2318 7380 9 480.0 0.94 746A2318 8180 9 449.1 1.15 747A1223 10320 9 456.9 1.71 749A1223 13500 8 484.6 0.34 744A2418 6270 8 512.0 0.47 745A2418 7380 8 539.5 0.75 746A2418 8180 8 515.3 0.58 745A2323 7380 8 552.8 0.95 746A2323 8180 8 590.3 1.59 747A2323 10320 6 618.4 0.77 746A2423 8180 6 663.3 1.27 747A2423 10320 6 573.0 0.24 744A2518 6270 6 597.4 0.36 745A2518 7380 ominal 1.1 KW Motor ominal m m 6 646.1 0.57 746A2518 8180 5 809.5 0.91 747A2523 10320 5 809.5 1.41 749A2523 13500 5 685.8 0.31 745A2618 7380 5 746.7 0.47 746A2618 8180 4 918.2 0.73 747A2623 10320 4 918.2 1.12 749A2623 13500 558 17.1 2.63 743A0120 1251 372 25.4 2.05 743A0220 1433 372 25.4 3.66 744A0220 1873 279 33.1 1.63 743A0320 1577 279 33.5 2.90 744A0320 2061 192 48.7 3.80 745A0224 2785 192 49.3 5.89 746A0224 3081 186 48.0 1.19 743A0420 1805 186 48.6 2.13 744A0420 2359 144 64.2 3.04 745A0324 3065 144 64.9 4.78 746A0324 3391 140 61.8 0.86 743A0520 1987 140 63.3 1.59 744A0520 2597 140 64.0 2.50 745A0520 3065 123 75.0 2.87 745A0227 3227 123 75.8 4.49 746A0227 3570 112 75.3 0.68 743A0620 2140 112 77.2 1.20 744A0620 2797 112 78.1 1.92 745A0620 3302 96 93.0 2.16 745A0424 3509 96 94.1 3.83 746A0424 3882 93 85.9 0.75 743A0720 2274 93 88.1 1.37 744A0720 2973 93 90.4 1.89 745A0720 3509 93 97.7 2.36 745A0327 3551 93 98.8 3.75 746A0327 3929 72 119.7 1.76 745A0524 3862 72 122.6 2.90 746A0524 4273 70 110.0 0.54 743A0820 2503 70 113.0 0.96 744A0820 3272 70 116.0 1.43 745A0820 3862 70 119.0 2.32 746A0820 4273 62 139.7 1.69 745A0427 4065 62 143.1 2.94 746A0427 4498 58 145.9 1.38 745A0624 4160 58 149.6 2.28 746A0624 4603 56 133.7 0.75 744A0920 3524 56 139.3 1.08 745A0920 4160 56 143.1 1.86 746A0920 4603 48 166.3 1.39 745A0724 4421 48 170.7 2.41 746A0724 4891 47 153.6 0.62 744A1020 3745 47 160.4 0.91 745A1020 4421 47 167.2 1.47 746A1020 4891 46 179.4 1.31 745A0527 4474 46 184.0 2.12 746A0527 4951 37 218.6 0.99 745A0627 4820 37 224.3 1.65 746A0627 5333 36 210.1 1.05 745A0824 4865 36 218.9 1.65 746A0824 5383 36 227.6 2.95 747A0824 6803 35 189.8 0.45 744A1120 4122 35 198.8 0.66 745A1120 4865 35 207.9 1.09 746A1120 5383 31 248.7 1.05 745A0727 5122 31 255.5 1.81 746A0727 5667 29 251.7 0.84 745A0924 5241 29 262.6 1.30 746A0924 5799 29 273.6 2.42 747A0924 7328 28 229.7 0.53 745A1220 5241 28 244.8 0.82 746A1220 5799 FE01/14 : Drive Design & Maintenance Manual 323

Section : 9 Roller Chain Drive Series W Gearboxes : Motorised selection GEARBOXES Bold print indicates 6 pole motor, italics indicates 2 pole motor, all others are 4 pole motors. ominal 1.5 KW Motor m 24 302.0 1.06 746A1024 6163 24 315.2 1.96 747A1024 7787 24 322.2 0.80 745A2024 5569 24 331.0 1.33 746A2024 6163 23 308.9 0.78 745A0827 5637 23 322.5 1.28 746A0827 6238 23 336.2 2.26 747A0827 7882 20 360.1 0.84 745A2124 6000 20 376.0 1.47 746A2124 6783 19 363.4 0.61 745A0927 6073 19 386.1 1.02 746A0927 6719 19 403.2 1.86 747A0927 8491 18 391.0 1.32 747A1124 8571 18 396.9 2.12 749A1124 11210 15 436.1 0.81 746A1027 7140 15 463.4 1.48 747A1027 9023 15 481.0 0.64 745A2027 6453 15 494.7 1.07 746A2027 7140 15 444.9 0.63 745A2224 6603 15 466.1 1.03 746A2224 7306 15 494.3 1.64 747A2224 9838 14 459.6 1.06 747A1224 9232 14 466.9 1.59 749A1224 12076 13 535.9 0.68 745A2127 6952 13 560.7 1.16 746A2127 7859 12 520.8 0.49 745A2324 7017 12 556.1 0.81 746A2324 7764 12 582.6 1.38 747A2324 10320 12 572.4 1.00 747A1127 9931 12 581.5 1.48 749A1127 12989 10 625.0 0.65 746A2424 8180 10 667.3 1.07 747A2424 10320 10 659.6 0.51 745A2227 7380 10 692.6 0.82 746A2227 8180 10 681.6 1.09 747A2227 10320 9 658.7 0.79 747A1227 10320 9 670.1 1.17 749A1227 13500 8 755.8 0.40 745A2327 7380 8 810.8 0.65 746A2327 8180 8 865.7 1.08 747A2327 10320 7 805.0 0.79 747A2524 10320 7 819.2 1.19 749A2524 13500 6 907.0 0.52 746A2427 8180 6 972.9 0.87 747A2427 10320 6 935.7 0.61 747A2624 10320 6 935.7 0.92 749A2624 13500 5 1187.3 0.62 747A2527 10320 5 1187.3 0.96 749A2527 13500 4 1346.7 0.50 747A2627 10320 4 1346.7 0.76 749A2627 13500 ominal m 377 34.6 3.76 745A0226 2210 377 35.0 6.01 746A0226 2446 283 45.6 3.18 745A0326 2433 283 45.6 5.15 746A0326 2692 192 66.4 2.79 745A0228 2785 192 67.2 4.32 746A0228 3081 188 66.2 2.27 745A0426 2785 188 66.9 4.04 746A0426 2785 144 87.6 2.23 745A0328 3065 144 88.5 3.51 746A0328 3391 141 86.2 1.86 745A0526 3065 141 88.2 2.95 746A0526 3391 125 100.6 2.14 745A0237 3227 125 101.7 3.35 746A0237 3570 125 101.7 6.39 747A0237 4511 113 105.2 1.43 745A0626 3302 113 107.8 2.33 746A0626 3653 96 126.8 1.58 745A0428 3509 96 128.3 2.81 746A0428 3882 ominal m 94 121.7 1.40 745A0726 3509 94 124.8 2.49 746A0726 3882 94 131.1 1.76 745A0337 3551 94 132.6 2.80 746A0337 3929 94 134.1 5.32 747A0337 4965 72 163.2 1.29 745A0528 3862 72 167.1 2.13 746A0528 4273 71 156.2 1.06 745A0826 3862 71 160.2 1.72 746A0826 4273 71 166.3 3.05 747A0826 5399 63 187.5 1.26 745A0437 4065 63 192.0 2.19 746A0437 4498 63 194.3 3.91 747A0437 5684 58 199.0 1.01 745A0628 4160 58 203.9 1.67 746A0628 4603 57 187.6 0.80 745A0926 4160 57 192.7 1.38 746A0926 4603 57 200.3 2.48 747A0926 5816 48 226.8 1.02 745A0728 4421 48 232.8 1.77 746A0728 4891 47 225.2 1.09 746A1026 4891 47 234.3 1.93 747A1026 6181 47 246.9 1.58 746A0537 4951 47 253.0 2.87 747A0537 6256 38 301.0 1.23 746A0637 5333 38 308.6 2.46 747A0637 6739 36 286.5 0.77 745A0828 4865 36 298.4 1.21 746A0828 5383 36 310.4 2.17 747A0828 6803 35 292.1 1.37 747A1126 6803 35 296.1 2.00 749A1126 8897 31 342.9 1.35 746A0737 5667 31 347.5 2.42 747A0737 7161 31 356.6 3.29 749A0737 9366 29 343.2 0.62 745A0928 5241 29 358.1 0.95 746A0928 5799 29 373.1 1.77 747A0928 7328 28 349.9 1.06 747A1226 7328 28 355.0 1.47 749A1226 9584 24 411.9 0.78 746A1028 6163 24 429.8 1.44 747A1028 7787 24 439.3 0.59 745A2028 5569 24 451.4 0.98 746A2028 6163 24 451.1 1.69 747A0837 7882 24 457.2 2.41 749A0837 10309 20 491.1 0.62 745A2128 6000 20 512.8 1.08 746A2128 6783 19 541.0 1.39 747A0937 8491 19 548.6 1.92 749A0937 11105 18 533.2 0.97 747A1128 8571 18 541.2 1.56 749A1128 11210 16 621.8 1.10 747A1037 9023 16 630.9 1.49 749A1037 11801 15 606.7 0.47 745A2228 6603 15 635.6 0.76 746A2228 7306 15 674.1 1.21 747A2228 9838 14 626.7 0.78 747A1228 9232 14 636.7 1.17 749A1228 12076 12 710.2 0.36 745A2328 7017 12 758.3 0.60 746A2328 7764 12 794.4 1.01 747A2328 10320 12 780.3 1.11 749A1137 12989 10 852.2 0.47 746A2428 8180 10 910.0 0.79 747A2428 10320 9 899.1 0.87 749A1237 13500 7 1097.8 0.58 747A2528 10320 7 1117.0 0.87 749A2528 13500 6 1275.9 0.45 747A2628 10320 6 1275.9 0.68 749A2628 13500 2.2 KW Motor ominal m 379 50.5 2.58 745A0229 2210 379 51.1 4.12 746A0229 2446 284 66.6 2.18 745A0329 2433 284 66.6 3.53 746A0329 2692 190 98.4 1.88 745A0236 2785 190 99.5 2.92 746A0236 3081 190 99.5 5.55 747A0236 3893 189 96.6 1.56 745A0429 2785 189 97.7 2.77 746A0429 2785 143 129.8 1.51 745A0336 3065 143 131.2 2.37 746A0336 3391 143 131.2 4.56 747A0336 4285 142 125.8 1.28 745A0529 3065 142 128.7 2.02 746A0529 3391 125 147.5 1.46 745A0245 3227 125 149.2 2.28 746A0245 3570 125 149.2 4.36 747A0245 4511 114 153.5 0.98 745A0629 3302 114 157.2 1.60 746A0629 3653 95 188.0 1.07 745A0436 3509 95 190.2 1.90 746A0436 3882 95 190.2 3.45 747A0436 4905 95 177.6 0.96 745A0729 3509 95 182.0 1.71 746A0729 3882 94 192.2 1.20 745A0345 3551 94 194.5 1.91 746A0345 3929 94 196.7 3.63 747A0345 4965 71 247.7 1.44 746A0536 4273 71 250.7 2.57 747A0536 5399 71 227.9 0.73 745A0829 3862 71 233.8 1.18 746A0829 4273 71 242.7 2.09 747A0829 5399 63 274.9 0.86 745A0445 4065 63 281.6 1.50 746A0445 4498 63 285.0 2.67 747A0445 5684 57 302.3 1.13 746A0636 4603 57 309.6 2.20 747A0636 5816 57 273.7 0.55 745A0929 4160 57 281.1 0.95 746A0929 4603 57 292.2 1.70 747A0929 5816 48 345.0 1.19 746A0736 4891 48 349.4 2.08 747A0736 6181 48 353.9 2.94 749A0736 8084 47 328.5 0.75 746A1029 4891 47 341.8 1.33 747A1029 6181 47 362.1 1.08 746A0545 4951 47 371.0 1.96 747A0545 6256 38 441.4 0.84 746A0645 5333 38 452.6 1.68 747A0645 6739 36 460.0 1.46 747A0836 6803 36 460.0 2.29 749A0836 8897 36 426.1 0.94 747A1129 6803 36 432.0 1.37 749A1129 8897 31 502.9 0.92 746A0745 5667 31 509.6 1.65 747A0745 7161 31 523.0 2.24 749A0745 9366 29 552.9 1.20 747A0936 7328 29 552.9 1.78 749A0936 9584 28 510.5 0.73 747A1229 7328 28 517.9 1.01 749A1229 9584 24 636.9 0.97 747A1036 7787 24 636.9 1.42 749A1036 10185 24 661.6 1.15 747A0845 7882 24 670.5 1.65 749A0845 10309 19 793.5 0.95 747A0945 8491 19 804.6 1.31 749A0945 11105 18 802.1 1.05 749A1136 11210 16 911.9 0.75 747A1045 9023 16 925.3 1.02 749A1045 11801 14 943.6 0.79 749A1236 12076 12 1144.4 0.76 749A1145 12989 9 1318.7 0.60 749A1245 13500 324

GEARBOXES Series W Gearboxes : Motorised selection Roller Chain Drive Section : 9 3.0 KW Motor ominal m 384 67.9 1.92 745A0239 2210 384 68.7 3.06 746A0239 2446 384 68.7 5.69 747A0239 3090 288 89.5 1.62 745A0339 2433 288 89.5 2.63 746A0339 2692 288 90.5 4.83 747A0339 3401 192 129.8 1.16 745A0439 2785 192 131.3 2.06 746A0439 2785 192 132.8 3.69 747A0439 3893 189 134.7 1.38 745A0238 2785 189 136.2 2.13 746A0238 3081 189 136.2 4.06 747A0238 3893 144 173.1 1.51 746A0539 3391 144 175.1 2.76 747A0539 4285 142 177.6 1.10 745A0338 3065 142 179.6 1.73 746A0338 3391 142 179.6 3.34 747A0338 4285 128 199.2 3.27 747A0253 4511 128 201.5 4.37 749A0253 5901 115 211.4 1.19 746A0639 3653 115 216.4 2.34 747A0639 4816 96 244.7 1.27 746A0739 3882 96 247.7 2.23 747A0739 4905 96 262.6 2.72 747A0353 4965 96 250.7 3.08 749A0739 6416 96 262.6 3.66 749A0353 6494 95 257.3 0.78 745A0438 3509 95 260.3 1.39 746A0438 3882 95 260.3 2.53 747A0438 4905 72 326.3 1.56 747A0839 5399 72 326.3 2.24 749A0839 7062 71 339.0 1.05 746A0538 4273 71 343.0 1.88 747A0538 5399 64 380.5 2.00 747A0453 5684 64 380.5 2.79 749A0453 7434 58 393.0 1.26 747A0939 5816 58 397.9 1.76 749A0939 7607 57 413.6 0.83 746A0638 4603 57 423.7 1.61 747A0638 5816 48 459.6 0.99 747A1039 6181 48 465.6 1.38 749A1039 8084 48 495.4 1.47 747A0553 6256 48 501.4 2.08 749A0553 8182 47 472.1 0.87 746A0738 4891 47 478.2 1.52 747A0738 6181 47 484.2 2.15 749A0738 8084 38 611.8 1.72 749A0653 8814 36 581.0 1.02 749A1139 8897 36 629.5 1.07 747A0838 6803 36 629.5 1.67 749A0838 8897 32 698.4 1.68 749A0753 9366 29 696.4 0.75 749A1239 9584 28 756.6 0.88 747A0938 7328 28 756.6 1.30 749A0938 9584 24 895.3 1.23 749A0853 10309 24 871.6 0.71 747A1038 7787 24 871.6 1.04 749A1038 10185 18 1097.6 0.77 749A1138 11210 14 1291.3 0.58 749A1238 12076 4.0 KW Motor ominal m 383 90.9 1.44 745A0244 2210 383 91.8 2.29 746A0244 2446 383 91.8 4.25 747A0244 3090 287 119.8 1.22 745A0344 2433 287 119.8 1.97 746A0344 2692 287 121.1 3.61 747A0344 3401 192 177.1 1.05 745A0246 2785 192 179.1 1.62 746A0246 3081 192 179.1 3.09 747A0246 3893 191 173.7 0.87 745A0444 2785 191 175.7 1.54 746A0444 2785 191 177.7 2.76 747A0444 3893 144 233.5 0.84 745A0346 3065 144 236.1 1.32 746A0346 3391 144 236.1 2.54 747A0346 4285 144 231.6 1.13 746A0544 3391 144 234.3 2.07 747A0544 4285 128 265.6 2.45 747A0255 4511 128 268.6 3.28 749A0255 5901 115 282.8 0.89 746A0644 3653 115 289.5 1.75 747A0644 4816 96 338.2 0.60 745A0446 3509 96 342.2 1.06 746A0446 3882 96 342.2 1.92 747A0446 4905 96 350.2 2.04 747A0355 4965 96 350.2 2.75 749A0355 6494 96 327.4 0.95 746A0744 3882 96 331.4 1.67 747A0744 4905 96 335.4 2.30 749A0744 6416 72 445.7 0.80 746A0546 4273 72 451.0 1.43 747A0546 5399 72 436.6 1.16 747A0844 5399 72 436.6 1.68 749A0844 7062 64 507.4 1.50 747A0455 5684 64 507.4 2.09 749A0455 7434 58 543.8 0.63 746A0646 4603 58 557.1 1.22 747A0646 5816 57 525.8 0.95 747A0944 5816 57 532.4 1.32 749A0944 7607 48 620.8 0.67 746A0746 4891 48 660.6 1.10 747A0555 6256 48 628.7 1.16 747A0746 6181 48 668.5 1.56 749A0555 8182 48 636.7 1.64 749A0746 8084 48 614.9 0.74 747A1044 6181 48 622.9 1.03 749A1044 8084 38 815.7 1.29 749A0655 8814 36 827.7 0.82 747A0846 6803 36 827.7 1.27 749A0846 8897 36 777.3 0.76 749A1144 8897 32 931.1 1.26 749A0755 9366 29 994.8 0.67 747A0946 7328 29 994.8 0.99 749A0946 9584 29 931.7 0.56 749A1244 9584 24 1146.0 0.54 747A1046 7787 24 1146.0 0.79 749A1046 10185 24 1193.8 0.93 749A0855 10309 18 1443.1 0.59 749A1146 11210 14 1697.8 0.44 749A1246 12076 5.5 KW Motor ominal m 388 124.6 3.14 747A0252 3090 388 124.6 4.18 749A0252 4042 291 164.3 2.67 747A0352 3401 291 164.3 3.54 749A0352 4449 195 242.8 2.28 747A0254 3893 195 245.5 3.06 749A0254 5092 194 241.0 2.03 747A0452 3893 194 241.0 2.79 749A0452 5092 146 320.2 1.87 747A0354 4285 146 320.2 2.57 749A0354 5605 146 317.7 1.53 747A0552 4285 146 317.7 2.08 749A0552 5605 128 365.2 1.78 747A0257 4511 128 369.3 2.39 749A0257 5901 116 392.6 1.71 749A0652 6038 97 464.1 1.42 747A0454 4905 97 469.5 1.96 749A0454 6416 97 454.9 1.70 749A0752 6416 96 481.5 1.49 747A0357 4965 96 481.5 2.00 749A0357 6494 73 611.6 1.06 747A0554 5399 73 618.8 1.48 749A0554 7062 73 592.0 1.24 749A0852 7062 64 697.6 1.09 747A0457 5684 64 697.6 1.52 749A0457 7434 58 755.5 1.24 749A0654 7607 49 863.4 1.21 749A0754 8084 48 908.3 0.80 747A0557 6256 48 919.2 1.14 749A0557 8182 38 1121.6 0.94 749A0657 8814 37 1122.5 0.94 749A0854 8897 32 1280.3 0.92 749A0757 9366 24 1641.4 0.68 749A0857 10309 7.5 KW Motor ominal m 388 169.8 2.30 747A0258 3090 388 169.8 3.07 749A0258 4042 291 224.0 1.96 747A0358 3401 291 224.0 2.59 749A0358 4449 194 328.6 1.49 747A0458 3893 194 332.3 1.67 747A0256 3893 194 328.6 2.04 749A0458 5092 194 336.0 2.24 749A0256 5092 146 433.2 1.12 747A0558 4285 146 438.1 1.37 747A0356 4285 146 433.2 1.53 749A0558 5605 146 438.1 1.88 749A0356 5605 116 535.4 1.26 749A0658 6038 97 635.0 1.04 747A0456 4905 97 620.3 1.25 749A0758 6416 97 642.4 1.44 749A0456 6416 73 836.9 0.77 747A0556 5399 73 807.3 0.91 749A0858 7062 73 846.7 1.08 749A0556 7062 58 1033.8 0.90 749A0656 7607 49 1181.5 0.89 749A0756 8084 36 1535.9 0.69 749A0856 8897 FE01/14 : Drive Design & Maintenance Manual 325

Section : 9 Roller Chain Drive Series W Gearboxes : Dimensions motorised X* GEARBOXES TRIPLE REDUCTIO X* Y* Z* Z* Y* FLAGE MOUTED *for motor dimensions see page 314 Dimension (mm) 740 741 742 743 744 745 746 747 749 A 45 54 70 80 100 120 140 170 200 B - 20 23 30 40 50 50 60 80 D 11 14 18 (19) 25 (24) 25 (28) 28 (35) 35 (38) 42 45 D1-9 11 14 19 24 24 28 30 G 45 55 70 80 95 112.5 129.5 160 180 G1 50 63 78 92 112 120 140 155 170 G3-45 53 64 75 90 108 135 155 H 35 40 50 60 72 86 103 127.5 147.5 I 25 30 40 50 63 75 90 110 130 K 34 44 60 70 85 90 100 115 120 KE** 6.5 (3) M6x11 (4) M6x10 (4) M8x10 (4) M8x14(8) M8x14(8) M10x18(8) M10x18(8) M12x21(8) L 42 56 71 85 103 112 130 144 155 M 55 65 75 85 95 115 130 165 215 (h8) 45 55 60 70 80 95 110 130 180 1 22.5 29.0 36.5 43.5 53.0 57.0 67.0 74.0 81.0 O 6.0 6.5 6.5 8.5 8.5 11.5 13.0 14.0 16.0 P - 75 87 100 110 140 160 200 250 Q 35.5 44 55 64 80 93 102 125 140 R 48.0 57.0 71.5 84.0 102.0 119.0 135.0 167.5 187.5 S 5.0 5.5 6.5 7.0 8.0 10.0 11.0 16.0 15.5 T 16.0 21.0 26.0 30.0 36.0 40.0 45.0 50.0 60.0 V 22.5 27 35 40 50 60 70 85 100 W 100 0 45 45 45 45 45 45 45 b 4 5 6 8 8 8 (10) 10 12 14 t 12.8 16.3 20.8 (21.8) 28.3 (27.3) 28.3 (31.3) 31.3 (38.3) 38.3 (41.3) 45.3 48.8 b1-3 4 5 6 8 8 8 8 t1-10.2 12.5 16.0 21.5 27.0 27.0 31.0 33.0 f - - - M6 M6 M8 M8 M10 M10 ~kg 0.7 1.2 2.3 3.5 6.2 9.0 13.0 21.0 48.0 All dimensions in mm. Dimension in brackets are the alternative bore option. ** umber in brackets are the number of tapped holes with the exception of the size 740 where the holes are not tapped. ~kg refers to the approximate weight without motor. 326

GEARBOXES Section : 9 Series W Gearboxes : Motor input dimensions B5 FLAGE dimensions bm tm Pm Dm B5 Flange IEC Motor Frame 56 63 71 80 90 100 112 132 160 180 200 Pm 120 140 160 200 200 250 250 300 350 350 400 Dm 9 11 14 19 24 28 28 38 42 48 55 bm 3 4 5 6 8 8 8 10 12 14 16 tm 10.4 12.8 16.3 21.8 27.3 31.3 31.3 41.3 45.3 51.8 59.3 * 749 Dimension tm is 40.3 (IEC 132) B14 FLAGE dimensions bm tm Pm Dm B14 Face IEC Motor Frame 56 63 71 80 90 100 112 132 160 180 200 Pm 80 90 105 120 140 160 160 200 350 350 400 Dm 9 11 14 19 24 28 28 38 42 48 55 bm 3 4 5 6 8 8 8 10 12 14 16 tm 10.4 12.8 16.3 21.8 27.3 31.3 31.3 41.3 45.3 51.8 59.3 * 749 Dimension tm is 40.3 (IEC 132) FE01/14 : Drive Design & Maintenance Manual 327

Section : 9 Roller Chain Drive Series W Gearboxes : flange dimensions GEARBOXES TRIPLE REDUCTIO FLAGE MOUTED STADARD OUTPUT FLAGE (Type FA) KA KB KC KM K KO KP KQ KW 740 45 6 3 55 40 6.5 (4) 75 70 45 741 54.5 6 4 68 50 6.5 (4) 80 70 45 742 67 7 4 80 min 60 9 (4) 110 95 45 743 90 9 5 90 min 70 11 (4) 125 110 45 744 82 10 6 150 115 11 (4) 180 142 45 745 111 13 6 165 130 14 (4) 200 170 45 746 111 13 6 175 152 14 (4) 210 200 45 747 131 15 6 230 170 14 (8) 280 260 45 749 140 15 6 255 180 16 (8) 320 290 22.5 OUTPUT FLAGE (Type FB) KA KB KC KM K KO KP KQ KW 742 97 7 4 80 min 60 9 (4) 110 95 45 743 120 9 5 90 min 70 11 (4) 125 110 45 744 112 10 6 150 115 11 (4) 180 142 45 745 90 13 6 130 110 14 (4) 160-45 746 122 18 6 215 180 14 (4) 250-45 747 180 15 6 230 170 14 (8) 280 260 45 OUTPUT FLAGE (Type FC) KA KB KC KM K KO KP KQ KW 742 80 9 5 115 95 9.5 (4) 140-45 743 89 10 5 130 110 9.5 (4) 160-45 744 98 10 5 165 130 11 (4) 200-45 745 - - - - - - - - - 746 110 17 6 165 130 11 (4) 200-45 OUTPUT FLAGE (Type FD) KA KB KC KM K KO KP KQ KW 742 58 12 5 100 80 9 (4) 120-45 743 72 14.5 5 115 95 11 (4) 140-45 744 107 10 5 165 130 11 (4) 200-45 745 - - - - - - - - - 746 151 13 6 175 152 14 (4) 210-45 328

GEARBOXES Section : 9 Series W Gearboxes : Accessories OUTPUT SHAFTs Single Extension Double Extension d h6 B B1 G1 L L1 f b1 t1 *Alternative small shaft available on request contact your local Authorised Distributor. All dimensions in mm. Kg Single 740* 11 g6 23 25.5 50 81 101-4 12.5 0.07 0.11 741 14 30 32.5 63 102 128 M6 5 16.0 0.14 0.16 742 18 40 43.0 78 128 164 M6 6 20,5 0.27 0.34 743 25 50 53.5 92 153 199 M10 8 28.0 0.60 0.75 744 25 50 53.5 112 173 219 M10 8 28.0 0.67 0.84 745 28 60 63.5 120 192 247 M10 8 31.0 0.94 1.20 746 35 80 84.5 140 234 309 M12 10 38.0 1.79 2.50 747 42 80 84.5 155 249 324 M16 12 45.0 2.70 3.44 749 45 80 85.0 170 265 340 M16 14 48.5 3.60 4.25 kg Double torque arm dimensions OUTPUT HUB DIMESIOS 3 K1 G KG KH R kg 740 70 14 17.5 8 15 0.17 741 85 14 24.0 8 15 0.18 742 100 14 31.5 10 18 0.24 743 100 14 38.5 10 18 0.27 744 150 14 49.0 10 18 0.57 745 200 25 47.5 20 30 1.1 746 200 25 57.5 20 30 1.26 747 250 30 62.0 25 35 1.92 749 250 30 69.0 25 35 2.23 All dimensions in mm. OTE: s 740 & 741 are not supplied with vibration resistant bushing 3 741 42.0 742 50.0 743 57.5 744 68.5 745 73.5 746 85.5 747 94.0 748 94.0 749 102.0 750 117.0 FE01/14 : Drive Design & Maintenance Manual 329

Section : 9 Roller Chain Drive Series W Gearboxes : Helical worm unit dimensions GEARBOXES * I2 FLAGE MOUTED *for motor dimensions see page 314 IEC Motor 63 Frame 71 Frame 80 & 90 Frame 742 743 744 743 744 745 746 745 746 747 749 A 70 80 100 80 100 120 140 120 140 170 200 E 147.0 167.0 192.0 177.5 202.5 228.5 260.5 241.0 273.0 317.5 357.5 G 165 185 212 193 220 251.5 285.5 267.5 301.5 356.5 396.5 G1 78 92 112 92 112 120 140 120 140 155 170 G2 120.0 140.0 167.0 140.0 167.0 198.5 232.5 198.5 232.5 287.5 327.5 H 50.0 60.0 72.0 60.0 72.0 86.0 103.0 86.0 103.0 127.5 147.5 I 40 50 63 50 63 75 90 75 90 110 130 I2 40 40 40 50 50 50 50 63 63 63 63 L1 71 85 103 85 103 112 130 112 130 144 155 K 60 70 85 70 85 90 100 90 100 115 120 KE** M6x10(4) M8x10(4) M8x14(8) M8x10(4) M8x14(8) M8x14(8) M10x18(8) M8x14(8) M10x18(8) M10x18(8) M12x21(8) M 75 85 95 85 95 115 130 115 130 165 215 60 70 80 70 80 95 110 95 110 130 180 1 36.5 43.5 53.0 43.5 53.0 57.0 67.0 57.0 67.0 74.0 81.0 O 6.5 8.5 8.5 8.5 8.5 11.5 13.0 11.5 13.0 14.0 16.0 P 87 100 110 100 110 140 160 140 160 200 250 Q 55 64 80 64 80 93 102 93 102 125 140 R 71.5 84.0 102.0 84.0 102.0 119.0 135.0 119.0 135.0 167.5 187.5 S 6.5 7.0 8.0 7.0 8.0 10.0 11.0 10.0 11.0 16.0 15.5 T 26 30 36 30 36 40 45 40 45 50 60 V 35 40 50 40 50 60 70 60 70 85 100 W 45 45 45 45 45 45 45 45 45 45 45 D 18 25 25 25 25 28 35 28 35 42 45 b 6 8 8 8 8 8 10 8 10 12 14 t 20.8 28.3 28.3 28.3 28.3 31.3 38.3 31.3 38.3 45.3 48.8 ~kg 3.4 4.6 7.3 5.1 7.8 10.6 14.6 12.4 16.4 24.4 51.4 All Dimesions in mm. For alternative hollow bore options see page 326 and the relevant motorised worm unit size. The frame size of the electric motor fitted to a worm unit determines the helical gear part of the asembly,the relevant dimensions are given in the above table Eg: Dimension G (the overall length) for a size 743 Helical Worm gearbox fitted with an IEC 71 Frame motor is 193mm. ** umber in brackets are the number of tapped holes. ~kg Refers to the approximate weight without motor. See page 314 for additional motor weight. 330

GEARBOXES Section : 9 Series W Gearboxes : on-motorised ratings : Input speed 500 rev/min O-MOTORISED RATIGS Input speed 500 rev/min. ominal Speed Input Power kw m Fr 1 Fr 2 ominal Speed Input Power kw m Fr 1 Fr 2 741 742 743 744 745 5.0 100 0.30 24 210 841 7.5 66.7 0.21 24 210 963 10 50.0 0.16 24 210 1060 15 33.3 0.12 24 210 1213 20 25.0 0.09 23 210 1336 25 20.0 0.10 29 210 1439 30 16.7 0.08 26 210 1529 40 12.5 0.06 23 210 1683 50 10.0 0.05 21 210 1813 60 8.3 0.04 19 210 1830 80 6.3 0.03 17 210 1830 5 100 0.60 49 350 1619 7.5 66.7 0.45 54 350 1853 10 50.0 0.35 54 350 2040 15 33.3 0.26 55 350 2335 20 25.0 0.19 52 350 2570 25 20.0 0.15 49 350 2769 30 16.7 0.16 58 350 2942 40 12.5 0.12 53 350 3238 50 10.0 0.10 49 350 3488 60 8.3 0.08 46 350 3490 80 6.3 0.06 40 350 3490 100 5.0 0.05 36 350 3490 5 100 1.1 92 490 2222 7.5 66.7 0.86 103 490 2544 10 50.0 0.67 103 490 2800 15 33.3 0.47 103 490 3205 20 25.0 0.33 93 490 3528 25 20.0 0.28 91 490 3800 30 16.7 0.29 108 490 4038 40 12.5 0.22 98 490 4445 50 10.0 0.17 91 490 4788 60 8.3 0.14 83 490 4840 80 6.3 0.11 75 490 4840 100 5.0 0.09 65 490 4840 7.5 66.7 1.50 184 700 3325 10 50.0 1.20 185 700 3660 15 33.3 0.85 187 700 4190 20 25.0 0.63 178 700 4611 25 20.0 0.48 164 700 4967 30 16.7 0.54 200 700 5279 40 12.5 0.40 185 700 5810 50 10.0 0.32 173 700 6259 60 8.3 0.26 160 700 6270 80 6.3 0.19 137 700 6270 100 5.0 0.16 128 700 6270 7.5 66.7 2.10 260 980 3925 10 50.0 1.70 270 980 4320 15 33.3 1.20 280 980 4945 20 25.0 0.98 285 980 5443 25 20.0 0.73 255 980 5863 30 16.7 0.77 300 980 6231 40 12.5 0.58 280 980 6858 50 10.0 0.44 250 980 7380 60 8.3 0.37 240 980 7380 80 6.3 0.29 215 980 7380 100 5.0 0.24 210 980 7380 746 747 749 7.5 66.7 3.30 410 1270 4343 10 50.0 2.70 435 1270 4780 15 33.3 2.10 490 1270 5472 20 25.0 1.60 470 1270 6022 25 20.0 1.20 440 1270 6487 30 16.7 1.40 550 1270 6894 40 12.5 0.95 480 1270 7588 50 10.0 0.75 450 1270 8174 60 8.3 0.59 400 1270 8180 80 6.3 0.45 365 1270 8180 100 5.0 0.35 330 1270 8180 7.5 66.7 5.50 690 1700 5488 10 50.0 4.60 740 1700 6040 15 33.3 3.40 790 1700 6914 20 25.0 2.50 750 1700 7610 25 20.0 2.10 790 1700 8198 30 16.7 2.10 870 1700 8711 40 12.5 1.50 810 1700 9588 50 10.0 1.30 800 1700 10320 60 8.3 0.98 710 1700 10320 80 6.3 0.72 630 1700 10320 100 5.0 0.56 570 1700 10320 7.5 66.7 8.60 1080 2100 7178 10 50.0 7.10 1160 2100 7900 15 33.3 5.50 1300 2100 9043 20 25.0 4.00 1230 2100 9953 25 20.0 3.20 1200 2100 10722 30 16.7 3.30 1400 2100 11394 40 12.5 2.40 1300 2100 12540 50 10.0 1.90 1220 2100 13500 60 8.3 1.50 1070 2100 13500 80 6.3 1.10 970 2100 13500 100 5.0 0.85 860 2100 13500 FE01/14 : Drive Design & Maintenance Manual 331