1 LITER HIGH PERFORMANCE CENTRIFUGES Our 1 Liter High Performance Centrifuges are designed for a variety of medical, industrial, and scientific applications. Ventilated Models 5694 and 5695 and refrigerated Models 5696, 5697, and 5698 are designed to meet your separation and concentration requirements. Refrigerated models provide a temperature range from -9C to 40C (15.8F to 104F). These high-speed, multipurpose benchtop centrifuges offer multiple power configurations for worldwide use. They accommodate swinging bucket and fixed angle rotors and can process a variety of tubes, bottles, and microsample tubes. Models 5696 (refrigerated) and 5694 (ventilated) Maintenance-free, brushless motor is permanently lubricated for efficiency and quiet operation. Acceleration and braking rates may be controlled to optimize runs. Repeat runs, with the same speed and time settings, are achieved by the touch of a button. Fail-safe cover interlock ensures that the cover is closed before a run can begin and keeps the cover closed for operator safety. Rugged steel cabinet construction ensures quiet operation and long term reliability. Automatic circuit breaker protects the centrifuge from damaging power surges. Suction feet anchor the centrifuge to your work surface to maintain stability and prevent walking. Fully automatic rotor recognition system internally detects and identifies the rotor installed to ensure that prescribed safety limits are not exceeded. Programs can be locked to avoid unwanted parameter changes. ENVIRO-SCAN MICROPROCESSOR CONTROL SYSTEM 4 Easy-to-use Enviro-Scan control panel provides two convenient modes of operation: Manual and Program. Manual is used to enter the temperature (refrigerated models only), speed/force, and time for individual runs. Program is used to define and save run parameters that you want to recall and reuse. Up to 99 specific sets of run parameters may be programmed (98 sets on refrigerated models). Programs are retained in non-volatile memory. Five versatile timing modes include At-Start, At-Speed, Continuous Operation (Hold), Centrifugal Integrator (replicates repetitive runs), and Momentary Spin (Pulse). Speed can be selected from 500 to 16,800 RPM in 50 RPM increments. Force can be selected from 50 to 30,300 xg in 50 xg increments. Speed is shown within 100 RPM and never requires calibration.
ENVIRO-SCAN (continued) RPM, RCF Displays RPM or RCF, based on selection Speed Switches between Actual and Set modes Time key/display Switches display from Actual to Set mode Mode Switches time display to At- Start, At-Speed, Hold, or Centrifugal Integrator Temperature key/display (Models 5696, 5697, 5698) Switches display from Actual to Set Mode Program key/display Switches display from Manual to Program mode Start Begins a run; indicator light blinks until the set run speed is reached RPM RCF Switches between speed and force display. Adjusts rotation radius when combined with Speed key Acceleration and Deceleration Selects Fast, Slow, and Input modes Numeric key pad Changes set parameters Manual Switches unit from Program to Manual mode Stop Open Stops a run or unlocks the cover Save Program Saves displayed settings Pulse Begins a run; run ends when the key is released SPECIFICATIONS Maximum Speed......... 16,800 RPM Maximum Force.......... 30,300 xg Maximum Sample Volume.. 1 liter (4x250ml) Operator Controls Rotor Chamber Temp.*...... -9C to 40C (15.8F to 104F) by 1C Rotation................. Counterclockwise RPM................... 500 to 16,800 RPM by 50 RPM RCF.................... 50 to 30,300 xg by 50 xg Spin Duration............ 0 through 99 hours, 59 minutes, and 59 seconds by 1 hour, 1 minute, and/or 1 second At-Start Timer, At-Speed Timer, Continuous Operation (Hold), Centrifugal Integrator, Momentary Spin (Pulse) Acceleration Rate Control.. Fast, Slow, or Input (choose speed at which acceleration switches from slow to full) Deceleration Rate Control.. Fast, Slow, or Input (choose speed at which deceleration switches from full to coast) Repeatability Rotation................. Within ±20 RPM Spin Timing.............. ±1 second Temperature*............. ±2C in range 4C to 20C (39.2F to 68F) Display................. RPM/RCF (speed/force), Time, Temperature*, and warning and error messages Stop, Start (indicated by lights) Modes: Actual (bright light display), Set (dim light display) Maximum dba.......... 70 (ventilated); 65 (refrigerated) Heat Output 5694, 5696.............. 2700 BTU/hr. 5696, 5697, 5698......... 2640 BTU/hr. (compressor off), 4200 BTU/hr. (compressor on) Refrigeration*.......... Non-CFC, non-flammable, and commercially available refrigerant 1/2 HP nominal Electrical Ventilated............... 5694: 120V, 60 Hz, 7.0 FLA 5695: 220/240V, 50/60 Hz, 6.0 FLA Refrigerated............. 5696: 120V, 60 Hz, 12.0 FLA 5697: 220/240V, 50 Hz, 8.0 FLA 5698: 220/230V, 60 Hz, 8.0 FLA Cord Set................ 6 ft. (1.8m) Plug................... 5694, 5696: NEMA 5-15P 5695, 5697, 5698: CEE 22, Standard V Certification............ 5694, 5695, 5696: CSA Certified 5695, 5697, 5698: CE Marked Dimensions 5694, 5695 5696, 5697, 5698 Height (cover open)....... 36.5" (92.7cm) 36.0" (91.4cm) Height (cover closed)...... 16.3" (41.4cm) 16.3" (41.4cm) Width.................. 20.6" (52.3cm) 30.8" (78.2cm) Depth.................. 25.8" (65.5cm) 25.8" (65.5cm) Clearance on All Sides..... 3.0" (7.6cm) 3.0" (7.6cm) Weight Net.................... 5694, 5695: 173 lbs. (78.5 kg) 5696, 5697, 5698: 254 lbs. (115.2 kg) Shipping............... 5694, 5695: 220 lbs. (99.8 kg) 5696, 5697, 5698: 304 lbs. (137.9 kg) 5 *Applies to refrigerated units only
4x250ml SWINGING BUCKET ROTOR No. 5808947 The Swinging Bucket Rotor (No. 5808947) offers large capacity, versatility, and convenience to meet your centrifugation requirements. Four buckets and a rotor recognition disk are included. The rotor achieves up to 5500 xg at 5300 RPM. Sealed adapters available for the swinging bucket rotor are listed below and are ordered separately. Those with part number series 58065xx are sold by the pair. Adapters with part number series 58057xx are sold with 12 adapters per pack. 6 REFRIGERATED VENTILATED TUBE MAXIMUM 4C MAX. MAXIMUM QUANTITY x ADAPTER ROTOR CAPACITY DESCRIPTION RPM/RCF RPM/RCF RPM/RCF RADIUS (FOR MAX. CAPACITY) 4x250ml Sealed IEC 2502 5300/5200 5100/4800 5000/4600 16.5cm 2 x 5806558 4x250ml Unsealed Corning 1260-250, 1280-250* 5300/5200 5100/4800 5000/4600 16.5cm 2 x 5806558 4x175/225ml Sealed Falcon 2076/2075 5300/5500 5100/5100 5000/4900 17.5cm 2 x 5806559 4x100ml Sealed Round Bottom, 38x111mm 5300/5450 5100/5050 5000/4850 17.3cm 2 x 5806557 4x80ml Amicon Centricon Plus 80* 5300/5200 5100/4800 5000/4600 16.5cm 2 x 5806558 4x20ml Amicon Centricon Plus 20* 5300/5200 5100/4800 5000/4900 16.5cm 2 x 5806556 8x50ml Sealed Corning 8240-50*, IEC 2997 5300/5500 5100/5100 5000/4900 17.5cm 2 x 5806556 Falcon/Corning Conical 5300/5500 5100/5100 5000/4900 17.5cm 2 x 5806560 12x25-30ml Sealed Universal, 25x107mm* 5300/4700 5100/4350 5000/4150 14.9cm 2 x 5806568 16x10ml Sealed** Kova/Urisystem* 5300/5500 5100/5100 5000/4900 17.5cm 2 x 5806561 20x15ml Sealed Falcon/Corning Conical 5300/5500 5100/5100 5000/4900 17.5cm 2 x 5806561 20x14ml Sealed Falcon 2059 Round with Cap*** 5300/4700 5100/4350 5000/4200 15.0cm 2 x 5806563 32x15ml Sealed 16.5x103mm 5300/5000 5100/4600 5000/4450 15.9cm 2 x 5806567 36x10-15ml Sealed Vacutainer 16x100, 16x125mm* 5300/5450 5100/5050 5000/4850 17.4cm 2 x 5806562 36x7-10ml Sealed Vacutainer 16x75, 16x100mm* 5300/4700 5100/4350 5000/4200 15.0cm 2 x 5806563 48x5-7ml Sealed Vacutainer 13x75, 13x100mm* 5300/5500 5100/5100 5000/4900 17.5cm 2 x 5806566 48x3-5ml Sealed Hemogard Vacutainer 13x75*, 10-12x75mm, Falcon 2063* 5300/5500 5100/5100 5000/4900 17.5cm 2 x 5806566 48x1.5/2.0ml Sealed Microtubes 5300/3700 5100/3400 5000/3250 11.7cm 2 x 5806565 48x0.7ml Sealed Microtainers 5300/3700 5100/3400 5000/3250 11.7cm 2 x 5806565 and 4 x 5805764 48x0.5ml Sealed PCR Microtubes 5300/3700 5100/3400 5000/3250 11.7cm 2 x 5806565 and 4 x 5805764 48x0.4ml Sealed Microtubes 5300/3700 5100/3400 5000/3250 11.7cm 2 x 5806565 and 4 x 5805763 48x0.25ml Sealed Microtubes 5300/3700 5100/3400 5000/3250 11.7cm 2 x 5806565 and 4 x 5805763 Amicon and Centricon are trademarks of Millipore Corporation. Vacutainer, Falcon, and Hemogard are registered trademarks of Becton Dickinson. PCR is a registered trademark of Perkin Elmer Corporation. Corning is a registered trademark of Corning. IEC is a registered trademark of Thermo IEC. *Check with the tube/bottle manufacturer for a current maximum rating because our rotor/accessory combination may exceed that rating. **Do not use the center hole. ***Use only the center hole and 12, 3, 6, and 9 o clock positions in the adapter for a total of 5 tubes per adapter.
MICROPLATE ROTOR The specialized TallStack Microplate Rotor (No. 5808244) includes two slotted, easy-to-remove carriers with cushions and a rotor recognition disk. The rotor achieves up to 3050 xg at 4400 RPM. Each carrier can accept a microplate stack up to 90mm tall. TallStack microplate rotor TUBE MAXIMUM ROTOR CAPACITY DESCRIPTION RPM/RCF RADIUS CUSHION REQUIRED 10 x Standard Microplate* 86x128mm 4400/3050 14.2cm Included Polyfiltronics Filtration/ 86x128x77mm 4400/3050 14.2cm Included Receiver Plate Assemblies Polyfiltronics Deepwell Microplate* One Deepwell per Carrier 86x128x43mm 4400/3050 14.2cm Included Two Deepwells per Carrier 86x128x86mm 4400/3050/2150** 14.2/9.9cm*** Not Required *Check with the plate manufacturer for a current maximum rating because our rotor/accessory combination may exceed that rating. **Bottom plate RCF/top plate RCF ***Bottom plate radius/top plate radius 48x1.5/2.0ml MICROTUBE ROTOR Sealed aluminum microtube rotor The Microtube Rotor (No. 5808848) is complete with a rotor recognition disk, sealing cover, and inner and outer O-rings. This 45 degree angle, sealed aluminum rotor achieves up to 30,300 xg at 16,800 RPM. The adapters, which are ordered separately, are sold with 12 adapters per pack. This high speed microtube rotor complies with the aerosol containment requirements of OSHA 29 CFR Part 1910.1030 Occupational Exposure to Bloodborne Pathogens; Final Rule dated 12/06/91. TUBE MAXIMUM QUANTITY x ADAPTER ROTOR CAPACITY DESCRIPTION RPM/RCF RADIUS (FOR MAX. CAPACITY) 48x1.5/2.0ml 11x44mm Microtube 16,800/30,300/26,500* 9.6/8.4cm** Not Required 48x1.5ml Amicon Microcon 16,800/30,300/26,500* 9.6/8.4cm** Not Required 48x0.7ml B/D Microtainer 16,800/30,300/26,500* 9.6/8.4cm** 4 x 5805763*** 48x0.5ml 8x32mm Microtube 16,800/30,300/26,500* 9.6/8.4cm** 4 x 5805763*** 48x0.4ml 6x54mm Microtube 16,800/30,300/26,500* 9.6/8.4cm** 4 x 5805764*** 48x0.25ml 6x32mm Microtube 16,800/30,300/26,500* 9.6/8.4cm** 4 x 5805764*** 7 *Outer row RCF/inner row RCF **Outer row radius/inner row radius ***Due to the high g-forces provided, the No. 5805763 and No. 5805764 adapters must be used to spin 0.25ml to 0.7ml microtubes. The traditional laboratory practice of cutting off the bottom of a 1.5ml microtube to be used as an adapter for smaller tubes, does not provide sufficient support to the smaller tubes at these high g-forces. Failure to use the No. 5805763 and No. 5805764 adapters could result in a tube/rotor mishap not covered under warranty.
6x85ml ANGLE ROTOR The Angle Rotor (No. 5808685) is a six place, sealed, 25 degree aluminum rotor that achieves up to 26,250 xg at 15,400 RPM. This high force rotor includes a rotor recognition disk, sealing cover, and inner and outer O-rings. Tube adapters are purchased separately. All adapters are sold by the pair. This angle rotor complies with the aerosol containment requirements of OSHA 29 CFR Part 1910.1030 Occupational Exposure to Bloodborne Pathogens; Final Rule dated 12/06/91. High speed, six place angle rotor 8 TUBE* MAXIMUM QUANTITY x ADAPTER ROTOR CAPACITY DESCRIPTION RPM/RCF RADIUS (FOR MAX. CAPACITY) 6x85ml Nalge 38.2x105.7mm 15,400/26,250 9.9cm Not Required 3118-0085 6x50ml Unsealed Falcon/Corning Conical* 15,400/24,650 9.3cm 3 x 5806651 (without rotor cover) 6x50ml Sealed Nalge 3118-0050 15,400/25,450 9.6cm 3 x 5806650 6x35ml Conical OR Nalge 3146-0050* 15,400/24,650 9.3cm 3 x 5816651 6x30ml Sealed Corning 8445-30 15,400/24,900 9.4cm 3 x 5806650 with Corning 8445-AO 6x28-30ml RB OR Nalge 3118-0028* 15,400/25,200 9.5cm 3 x 5806630 Sealed Nalge 3118-0030* 6x25ml Sealed Corning 8446-25 15,400/24,900 9.4cm 3 x 5806650 with Corning 8446-AO 6x15ml Unsealed Falcon/Corning Conical* 15,400/23,600 8.9cm 3 x 5806650 with (without rotor cover) 3 x 5806715 6x15ml Sealed Corning 8441-15** 15,400/24,150 9.1cm 3 x 5806650 with Corning 8441-AO 6x10ml 16x75-100mm** 15,400/24,400 9.2cm 3 x 5806650 with 3 x 5807245 6x7ml 13x75-100mm** 15,400/24,150 9.1cm 3 x 5806650 with 3 x 5807256 6x5ml 10-12x75mm 15,400/24,150 9.1cm 3 x 5806650 with 3 x 5807246 18x1.5/2.0ml Microtubes*** 15,400/24,900 9.4cm 3 x 5806650 with 3 x 5807248 *Tube volume is nominal; volume is actually less due to rotor angle. **Check with the tube manufacturer for a current maximum rating because our rotor/accessory combination may exceed that rating. During independent testing conditions of 30 minute one time only runs and with a maximum 35ml fluid sample, the Falcon and Corning tubes performed to 21,000 xg without leaking. ***Variations in microtube cap design can produce interference, causing fewer than three microtubes to fit in each adapter.
8x50ml CONICAL ANGLE ROTOR The Conical Angle Rotor (No. 5808850) is an eight place, 25 degree fixed angle aluminum rotor that achieves up to 25,250 xg at 15,100 RPM (23,900 xg/14,700 RPM at 4C (39.2F)). The rotor includes a rotor recognition disk, sealing cover, and inner and outer O-rings. Adapter No. 5806715 is sold by the pair, and adapter No. 5850546 is sold individually. High force, eight place conical angle rotor This angle rotor complies with the aerosol containment requirements of OSHA 29 CFR Part 1910.1030 Occupational Exposure to Bloodborne Pathogens; Final Rule dated 12/06/91. TUBE MAXIMUM 4C MAX. QUANTITY x ADAPTER ROTOR CAPACITY DESCRIPTION RPM/RCF RPM/RCF RADIUS (FOR MAX. CAPACITY) 8x50ml Sealed Falcon 2070 Conical* 15,100/25,250 14,700/23,900 9.9cm Not Required 8x50ml Sealed Corning 430522 Conical* 15,100/25,250 14,700/23,900 9.9cm Not Required 8x50ml Sealed 28x103mm Oak Ridge 15,100/24,450 14,700/23,200 9.6cm 8 x 5850546 8x35ml Sealed Nalge Conical OR 15,100/25,250 14,700/23,900 9.9cm 28.8x114.1mm Not Required 3146-0050, 3148-0050 8x30ml Sealed Corning 8445-30* 15,100/23,950 14,700/22,700 9.4cm 8 x 5850546 with Corning 8445-AO 8x25ml Sealed Corning 8446-25* 15,100/23,950 14,700/22,700 9.4cm 8 x 5850546 with Corning 8445-AO 8x15ml Sealed Falcon 2095 Conical* 15,100/23,450 14,700/22,200 9.2cm 4 x 5806715 Corning 430052 Conical* 15,100/23,450 14,700/22,200 9.2cm 4 x 5806715 Corning 8441-15* 15,100/23,450 14,700/22,700 9.2cm 8 x 5850546 with Corning 8441-AO *Check with the tube manufacturer for a current maximum rating because our rotor/accessory combination may exceed that rating. During independent testing conditions of 30 minute one time only runs and with a maximum 40ml fluid sample, the Falcon 2070 and 2095 and the Corning 430522 and 430052 conical tubes performed to the maximum rotor speeds published above without leaking. 9