PARTS BOOK ROTARY HEADS 60 CUT COMBO MID-MOUNT 5.0.8 DIAMOND MOWERS, LLC 350 E 60 th St. North Sioux Falls, SD 5704 FOR WARRANTY CALL DIAMOND MOWERS DIRECT: 888-960-0364 OUR TECHNICIANS WILL DIAGNOSE YOUR SITUATION OVER THE PHONE TO GET YOU UP AND RUNNING QUICKLY. Phone: 605-977-3300 Fax: 605-655-5870 www.diamondmowers.com DIAMOND MOWERS, LLC
Page Foreword This manual contains the parts breakdown and identification of the various components and structures that make up your mower implement. The illustrations, drawings, and diagrams in this manual are based on the latest information available at the time of publication. Your machine may have product improvements and features not yet contained in this parts manual. Diamond Mowers, LLC reserves the right to make changes at any time without notice or obligation. Diamond Mowers, LLC and Wetblade are trademarks of Diamond Mowers, LLC. This manual should be consulted prior and while assembling the unit, and anytime parts or assembly clarification is needed. Copyright 06 Diamond Mowers, LLC All rights reserved. While every precaution has been taken in the preparation of this manual, the publisher assumes no responsibility for errors or omissions. No part of this book covered by the copyrights heron may be reproduced or copied in any form or by any means graphic, electronic, or mechanical, including photocopying, taping, or information storage and retrieval systems without written permission of the publisher.
Page 3 Table of Contents ROTARY HEADS 4 SIDE ROTARY HEAD - 60 COMBO DECK, DIRECT DRIVE 5 SIDE ROTARY HEAD - 60 BLADE CONFIGURATIONS 6 SIDE ROTARY HEAD - 60 CHAIN GUARD ATTACHMENT 8 DRAFT BEAM ASSEMBLIES 9 DRAFT BEAM - COMBO LIFT, STD 0 DRAFT BEAM - COMBO LIFT, NARROW DRAFT BEAM - DX DECK ASSEMBLIES 3 30-054 - MOTOR ASSEMBLY 4 35-0088 - DIRECT DRIVE SPINDLE 5 LIFT ASSEMBLIES 6 4-000 - 3X0 WELDED CYLINDER 7 4-0004 - 3X WELDED CYLINDER, SLUGGED 8 ELECTRICAL ASSEMBLIES 9 LIMIT SWITCH - DRAFT BEAM HEIGHT LIMITER 0
ROTARY HEADS
ROTARY HEADS Page 5 SIDE ROTARY HEAD - 60 COMBO DECK, DIRECT DRIVE 3/8 LOCK WASHER 0-0005 5/6 FLAT WASHER 33-005 3 5/8 H.S. LOCK WASHER -0043 4 /4 X 3/4 NC HEX CAP 4-0588 5 -/8 H.S. FLAT WASHER - 6-0057 6 3/8 X -/4 NC HEX CAPSCREW 7-0533 7 /4 NC NYLOCK NUT 4-0 8 5/8 X -/4 H.S. NF HEX CAPSCREW -069 9 BLADE BOLT - HEX BASE - 6-0759 0 3/8 X -/4 NC PLOW BOLT 0-0804 3/8 NC HEX NUT -00 3/8 NC NYLOCK NUT 6-04 3 -/8 NF CASTLE NUT - 6-050 4 5/8 H.S. NF STOVER NUT 6-43 5 ROLLPIN - 6-005 6 FLAP 8-000 7 MJ X FJX-45DEG FITTING -45 8 ADAPTER, #0FLG X MJIC-90DEG -67 9 #0 FLANGE KIT -05 0 HIGH SUCTION KNIFE - 6-0004 DISH 4-07 DECK SHELL 5-0054 3 MOTOR 30-054 4 FLAP BAR PLATE 3-0054 5 SPINDLE 35-0088 6 FLAP BAR 4-00 7 SKID SHOE 4-0003 8 MOTOR BOLT LOCK TAB 4 3-0503 9 MOTOR BOLT LOCK BASE 3-0504 30 /-0 X -3/4 H.S. NF HEX CAP GR.8 4-0664 3 ADAPTER, /4MOR X 3/8MJIC -597 3 REPLACEABLE HEX INSERT Avail 90-700 33 BLADE KITS) 60" SIDE ONLY Includes 5, 9, 3, 5, & 0 44-03 60" SIDE & 60" REAR Includes 5, 9, 3, 5, & 0 44-034 60" SIDE & 7" REAR Includes 5, 9, 3, 5, 0, & #-000 for the 7" 44-035 7" SIDE & 60" REAR Includes 5, 9, 3, 5, 0, & #-000 for the 7" 44-035
ROTARY HEADS Page 6 SIDE ROTARY HEAD - 60 BLADE CONFIGURATIONS -/8 H.S FLAT WASHER 3-0057 BLADE MOUNTING BOLT 3-0759 3 BLADE MOUNTING NUT 3-050 4 ROLLPIN 3-005 5 KNIFE * /" GRASS BLADE 3-000 ** /" GRASS BLADE (HIGH SUCTION) 3-0004 6 60" TRI-HEX DISH 4-0086 7 REPLACEABLE HEX INSERT Avail 90-700 BLADE MOUNTING BOLT 3-0503 BLADE MOUNTING NUT 3-008 3 KNIFE * /" GRASS BLADE 3-000 ** /" GRASS BLADE (HIGH SUCTION) 3-0004 4 BLADE DISH 4-0076 5 REPLACEABLE INSERT Avail 90-7007 BLADE MOUNTING BOLT 3-0503 BLADE MOUNTING NUT 3-008 3 KNIFE * /" GRASS BLADE 3-000 ** /" GRASS BLADE (HIGH SUCTION) 3-0004 4 BLADE DISH 4-000
ROTARY HEADS Page 7 SIDE ROTARY HEAD - 60 BLADE CONFIGURATIONS -/8 H.S FLAT WASHER 3-0057 BLADE MOUNTING BOLT 3-0759 3 BLADE MOUNTING NUT 3-050 4 ROLLPIN 3-005 5 KNIFE * 50" BRUSH KNIFE - /" 3-0003 ** 50" GRASS KNIFE, HIGH SUCTION - /" 3-0005 *** 50" BRUSH BLADE - 5/8" 3-0006 **** 50" BI-DIRECTIONAL BLADE - /" 3-00 ***** 50" BRUSH KNIFE - REVERSE ROTATION - 5/8" 3-007 6 60'' BOOM DECK DISH 4-045 7 REPLACEABLE HEX INSERT Avail 90-700 -/8 SAE H.S. FLAT WASHER -0057 KNIFE MOUNTING BOLT -0759 3 KNIFE MOUNTING NUT -050 4 /4 X ROLL PIN -005 5 50" BI-DIRECTIONAL BLADE -00 6 BLADE BAR 4-00 -/8 H.S FLAT WASHER 3-0057 BLADE MOUNTING BOLT 3-0759 3 BLADE MOUNTING NUT 3-050 4 ROLLPIN 3-005 5 KNIFE * /" GRASS BLADE 3-000 ** /" GRASS BLADE (HIGH SUCTION) 3-0004 6 60"ROUND DISH, -3 BLADE 4-07 7 REPLACEABLE HEX INSERT Avail 90-700
ROTARY HEADS Page 8 SIDE ROTARY HEAD - 60 CHAIN GUARD ATTACHMENT 3/8 FLAT WASHER 4-0009 5/6 FLAT WASHER 8-005 3 3/8 X -/ NC HEX CAP 6-059 4 3/8 X -/4 NC HEX CAP 7-0533 5 3/8 NC NYLOCK NUT 3-04 6 GALVANIZED CABLE (SOLD PER FOOT) ft -003 7 /4" WIRE ROPE CLAMP -0033 8 5/6" ZINC CHAIN - 6 LINKS 4-0035 9 5/6" ZINC CHAIN - 7 LINKS 6-0036 0 CHAIN GUARD 4-0088
DRAFT BEAM ASSEMBLIES
DRAFT BEAM ASSEMBLIES Page 0 DRAFT BEAM - COMBO LIFT, STD FLAT WASHER -000 7/6 X 3-/4 NC HEX CAPSCREW 3-050 3 3/8 X -/4 NC HEX CAPSCREW -053 4 7/6 NC NYLOCK NUT 3-003 5 3/8 NC NYLOCK NUT -04 6 R-CLIP -00 7 /4 X ROLL PIN 6-005 8 3 X 0 WELDED CYLINDER 4-000 9 3 X WELDED CYLINDER 4-0004 0 /8 GREASE ZERK 3-0003 /4 GREASE ZERK 7 3-0004 X 7 PIN 7-0003 3 CLEVIS PIN 3 7-0004 4 LINKAGE PIN 7-0009 5 DRAFT BEAM/MAIN FRAME PIN 7-050 6 EAR PIN 7-0509 7 BOSS 34-000 8 HARDENED BUSHING 6 34-0005 9 DRAFT BEAM COMBO DRAFT BEAM 4-00 COMBO DRAFT BEAM, 4" REAR OFFSET 4-383 0 PIVOT ARM 4-005 LINKAGE ARM LEFT 4-006 LINKAGE ARM RIGHT 4-007
DRAFT BEAM ASSEMBLIES Page DRAFT BEAM - COMBO LIFT, NARROW 8 8 5 9 8 6 5 4 7 3 3 3 5 3 0 4 0 9 0 3 4 3 9 3 3 0 5 9 6 3 7 5 3 0 9 5 6 REF# 3 4 5 6 7 8 9 0 3 4 5 6 7 8 9 0 3 4 5 PARTS DESCRIPTION FLAT WASHER GR 5 7/6 X 3-/4 NC HEX CAP GR 5 3/8 X -/4 NC HEX CAP GR 5 3/4 X -/ NC HEX CAPSCREW 7/6 NC NYLOCK NUT 3/8 NC NYLOCK NUT 3/4 NC HEX NUT 3/6 R-CLIP /4'' ROLL PIN x " 3 X 0 WELDED CYLINDER 3 X WELDED CYLINDER, SLUGGED GREASE ZERK /8'' STRAIGHT GREASE ZERK /4'' STRAIGHT PIN X 7-5/8 CYLINDER PIN, 3-/" LINKAGE PIN PIN -/ X 4-/ CAP SWING FLAIL PIN.5 X.75 LINKAGE BOSS BUSHING -/OD X ID X 0GA BUSHING PIVOT LINKAGE LINKAGE ARM LEFT COMBO DRAFT BEAM LINKAGE LEFT LINKAGE ARM RIGHT COMBO DRAFT BEAM LINKAGE RIGHT COMBO DRAFT BEAM,.5 FORWARD OFFSET REQ 3 3 6 7 3 6 PART# -000-050 -053-0563 -003-04 -033-00 -005 4-000 4-0004 3-0003 3-0004 7-0003 7-0004 7-0009 7-0509 7-055 34-000 34-0005 34-0060 4-005 4-006 4-007 4-49 TORQUE (ft-lbs) 49.4 30.9 67.0 TORQUE (Nm) 67.0 4.9 36.0
DRAFT BEAM - DX DRAFT BEAM ASSEMBLIES Page FLAT WASHER -000 7/6 LOCK WASHER 3-0003 3 3/8 LOCK WASHER -0005 4 7/6 X 3-/4 NC HEX CAPSCREW 3-050 5 3/8 X -/4 NC HEX CAPSCREW -053 6 7/6 NC NYLOCK NUT 3-003 7 3/8 NC NYLOCK NUT -04 8 R-CLIP -00 9 /4 X ROLL PIN 6-005 0 3 X 0 WELDED CYLINDER 4-000 3 X WELDED CYLINDER 4-0004 /8 GREASE ZERK 3 3-0003 3 /4 GREASE ZERK 6 3-0004 4 X 7 PIN 7-0003 5 CLEVIS PIN 3 7-0004 6 LINKAGE PIN 7-0009 7 DRAFT BEAM/MAIN FRAME PIN 7-050 8 EAR PIN 7-0509 9 BOSS 34-000 0 HARDENED BUSHING 6 34-0005 PIVOT ARM 4-005 LINKAGE ARM LEFT 4-006 3 LINKAGE ARM RIGHT 4-007 4 DRAFT BEAM ROTARY, DIM A = 5-/3" 4-037 FLAIL, DIM A = 60-5/3" 4-038
DECK ASSEMBLIES
30-054 - MOTOR ASSEMBLY DECK ASSEMBLIES Page 4 SNAP RING 30-009 OUTBOARD BEARING 30-00 3 BUSHING 4 30-0 4 THRUST PLATE 30-0 5 SEAL RETAINER 30-07 6 M365 SEAL KIT Avail 30-0 7 -/4" M365 GEAR HOUSING 30-06 8 SHAFT SEAL 50 PSI (included in M365 seal kit) 30-0 500 PSI 30-56 9 SHAFT END COVER 30-086 0 CHECK ASSEMBLY 30-087 ALIGNMENT BUSHING 4 30-090 PORT END COVER 30-09 3 STUD 4 Call 4 WASHER 4 30-093 GEAR SET OPTION A: 5 -/4" GEAR SET 30-65 GEAR S ET OPTION B: 6 RETAINING RING 30-09 7 WASHER 30-00 8 -/4" GEAR SET 30-05 9 CONTINENTAL SHAFT, SPLINED 30-44 0 PLUG 30-096 * SEAL APPLICATOR TOOL (not shown) Avail 30-048
35-0088 - DIRECT DRIVE SPINDLE DECK ASSEMBLIES Page 5 BEARING 0-0055 LOCKING WASHER -0048 3 3/8 X -3/4 NC SKT HEAD CAPSCREW 8-0703 4 /4 X / NC CAPSCREW 4-074 5 -/ SPANNER NUT -037 6 LARGE SNAP RING -0 7 SMALL SNAP RING -0 8 PIPE PLUG -36 9 /8 X 90 GREASE ZERK 3-0005 0 UPPER SEAL 33-0035 LOWER SEAL 33-0057 SPINDLE HOUSING 35-00 3 SEAL/MOTOR MOUNT 35-00 4 ALIGNMENT PIN 35-003 5 SPACER 35-0050 6 BOTTOM SEAL PLATE 35-0063 7 SPACER 35-0064 8 BOTTOM PLATE 35-0065 9 GREASE CATCH 35-0066 0 SPINDLE SHAFT COMPLETE 35-0090 * SPLINED INSERT KIT 35-009 BREATHER 80-06 3 3/8 LOCK WASHER GR 5 8-0005
LIFT ASSEMBLIES
4-000 - 3X0 WELDED CYLINDER LIFT ASSEMBLIES Page 7 PISTON ROD 4-30 CLEVIS ASSEMBLY 4-60 3 BUTT & TUBE ASSEMBLY 4-40 4 GLAND 4-55 5 PISTON 4-50 6 LOCKNUT 4-0 7 SEAL KIT 33-0038
LIFT ASSEMBLIES Page 8 4-0004 - 3X WELDED CYLINDER, SLUGGED PISTON ROD 4-3 CLEVIS ASSEMBLY 4-60 3 BUTT & TUBE ASSEMBLY 4-4 4 GLAND 4-55 5 PISTON 4-50 6 LOCKNUT 4-0 7 SLUG 4-9 8 SEAL KIT 33-0038 9 SET SCREW -007
ELECTRICAL ASSEMBLIES
ELECTRICAL ASSEMBLIES Page 0 LIMIT SWITCH - DRAFT BEAM HEIGHT LIMITER #0-4 X SHCS -0786 #0-4 NYLOCK NUT -05 3 LIMIT SWITCH 6-006 4 4-6GA MALE PUSH-ON CONNECTOR 6-0040 5 4-6GA FEMALE PUSH-ON CONNECTOR 6-004 6 4/ PRIMARY WIRE Avail/ft 6-004 7 3/8 CONDUIT STRAIN RELIEF 6-0043 8 CAM TILT BRACKET LEFT 4-0039 RIGHT 4-0040 9 LIMIT SWITCH PLATE 3-003
(PAGE INTENTIONALLY BLANK)
00% SATISFACTION GUARANTEE GET IT, LOVE IT, or LEAVE IT! 7-HOUR PARTS SHIPPING GUARANTEE