MODELS 80 / 100 / 120 / 130 / 130B RUNNING GEARS Operator's Manual & Parts Catalog (8 Ton) Beginning with Serial #D43060100 (10 Ton) Beginning with Serial #D43070100 (12 Ton) Beginning with Serial #D43060100 (13 Ton) www.parkerindustries.com Part No. 30630
TABLE OF CONTENTS GENERAL INFORMATION... 2 SAFETY... 3 SECTION I -- OPERATIONS OPERATIONS... 6 LOAD CAPACITY... 6 TRACTOR BALLAST... 6 TRACTOR DRAWBAR... 6 TRANSPORT CHAIN (OPTIONAL)... 6 CHECKING WHEEL BOLTS... 6 CHECKING CHASSIS... 6 TIRE INFLATION... 6 LOAD DISTRIBUTION... 6 LOAD DISTRIBUTION... 6 ADJUSTABLE QUICK HITCH TONGUE... 6 TONGUE LENGTH... 6 ADJUSTABLE WHEEL LENGTH... 6 TRANSPORT CHAIN (OPTIONAL)... 7 SECTION II -- SERVICE ADJUSTABLE WHEEL TOE-IN... 8 MAINTENANCE INSTRUCTIONS... 9 BRAKE SYSTEMS... 9 SLIDING HITCH & LATCH... 9 MASTER CYLINDER...10 BRAKE SHOE ADJUSTMENT... 10 BRAKE BLEEDING... 10 MANUAL BLEEDING... 10 TORQUE CHART... 10 SECTION III -- ASSEMBLY ASSEMBLY INSTRUCTIONS... 12 MODELS WITHOUT BRAKES... 12 MODEL WITH BRAKES... 14 TONGUE ASSEMBLY... 15 SECTION IV -- PARTS MODEL #80 COMPONENTS... 16 MODEL #100 COMPONENTS... 18 MODEL #120 COMPONENTS... 20 MODEL #130 COMPONENTS... 22 MODEL #130B COMPONENTS... 24 TONGUE WITH BRAKE COMPONENTS... 26 BRAKE COMPONENTS... 27 GENERAL INFORMATION When selecting tires for your running gear be sure to select tires that have the proper load carrying capacity. Selecting tires that do not have sufficient capacity can cause unnecessary or abnormal tire wear and/or possible tire blowouts. For your future reference when ordering parts, record the serial number of your gear in the space below. (Serial number is located on right hand side of front assembly.) NOTE: Due to continuing improvements in the design and manufacture of our products, and normal changes in the marketplace, all specifications contained herein are subject to change without notice. -2-
THANK YOU FOR YOUR PURCHASE! Please fill out and retain this portion for your records. For warranty consideration, please contact dealer where purchased. The serial number plate is located on the front of the front frame of the RUNNING GEAR Product Serial Number Date of Purchase Dealer City State Zip Please supply this information when you have questions or when ordering repair or replacement parts. Your dealer needs this information to give you prompt, efficient service. SAFETY REMEMBER: THINK SAFETY A CAREFUL OPERATOR IS THE BEST INSURANCE AGAINST AN ACCIDENT! OM-00229-A No accident-prevention program can be successful without the wholehearted cooperation of the person who is directly responsible for the operation of the equipment. To read accident reports from all over the country is to be convinced that a large number of accidents can be prevented only by the operator anticipating the result before the accident is caused and doing something about it. No power-driven equipment, whether it be transportation or processing, whether it be on the highway, in the harvest field, or in the industrial plant, can be safer than the man who is at the controls. If accidents are to be prevented--and they can be prevented--it will be done by the operators who accept the full measure of their responsibility. It is true that the designer, the manufacturer, and the safety engineer can help; and they will help, but their combined efforts can be wiped out by a single careless act of the operator. It is said that, "the best kind of a safety device is a careful operator." We ask that you be that kind of operator. -3-
SAFETY AVOID POSSIBLE INJURY Always use proper safety precautions. Most accidents are a result of failure to practice safety. Accidents cause lost time and suffering. Do not operate your RUNNING GEAR without thoroughly reading this manual. Follow all safety precautions as outlined in this manual and in the tractor operator's manual. All machinery should be operated only by those who are experienced, responsible, and have been delegated to do so. Do not exceed the gross load capacity of the running gear. BEFORE OPERATING Always make certain everyone and everything is clear of the machine before beginning operation. Always shut tractor engine off and remove key from ignition before working on implement. When hitching the wagon to the tractor, back the tractor past the clevis. Then move it slowly forward so that, in making the connection, the tractor will be moving away from you. Avoid working under an implement; however, if it become absolutely unavoidable, make sure implement is safely blocked. Do not wear loose fitting clothes, as they may catch on moving parts. Do not grease or oil equipment while it is in operation. Be sure the tires are inflated to the recommended pressure. Be sure all hardware is tight and drawbar pin is properly installed with safety lock. DURING OPERATION Do not allow anyone to ride on the RUNNING GEAR. Make sure everyone is clear before operating the machine or tractor. Regulate speed to field conditions. Maintain complete control at all times. -4- Use extreme care when operating close to ditches, fences or on hillsides. Do not leave tractor or implement unattended with engine running. Never attempt to operate any implement unless you are in the driver's seat. Do not dismount from a moving tractor. Do not disconnect the RUNNING GEAR from tractor until the wheels have been blocked to prevent unit from rolling. BEFORE TRANSPORTING Before towing unit(s), use a tow vehicle with the gross weight equal to, or greater than the gross weight of all the equipment being pulled. Be sure the load is well balanced on RUN- NING GEAR to insure proper trailing. Secure transport chain to RUNNING GEAR tongue and to the tractor drawbar before transporting. When pulling several units, secure with transport chain between each unit. Make sure that all safety decals, SMV emblem, and reflectors are clean and in place on the machine. Latch the tractor brake pedals together before transporting. Lock the tractor drawbar on center and secure the hitch pin to prevent drawbar movement or loss of transport pin. Comply with state and local laws governing highway safety when moving machinery. Use accessory lighting or warning lights when transporting at night to adequately warn operators of other vehicles. Be sure tongue latch is locked into position before transporting to prevent inadvertent extension of hitch. DURING TRANSPORT Use good judgement when transporting implements on highway. Maintain complete control at all times. Regulate speed to road conditions. Maximum speed of vehicle with implements should never exceed 20 m.p.h. and then only under ideal road and traffic conditions.
SAFETY Be sure RUNNING GEAR is trailing straight to maintain full control. If unit is swaying or whipping side-to-side, stop operation and check for proper tire pressure, even load distribution, worn, loose or damaged steering or frame components, repair immediately. Drive at speeds slow enough to insure your safety as well as others. Regulate speed during off highway travel. Do not travel faster than 10 m.p.h. COMPLY WITH ALL SAFETY WARNINGS AND CAUTIONS IN THIS MANUAL, AND IN TRACTOR OPERATOR'S MANUAL. Slow down before making sharp turns or using the brakes. Drive slowly over rough ground, side hills, and around curves to avoid tipping. -5-
OPERATIONS SECTION I OPERATIONS LOAD CAPACITY The following models are designed to operate with a total maximum gross load of... Model 80 = 16,000 lbs. Model 100 = 20,000 lbs. Model 120 = 24,000 lbs. Model 130/130B = 26,000 lbs. Gross load is the combined weight of the RUNNING GEAR, wagon box or bed, and the material being hauled. Net load is the weight of the material being hauled. Operator safety and RUNNING GEAR life will depend on the correct combination of load weight, tire load capacity and tire inflation. RUNNING GEAR rating is the maximum recommended gross load for the wagon gear when the tire load capacity is greater than the RUNNING GEAR capacity. When the tire load capacity is less than the RUNNING GEAR rating, the tire load capacity becomes the maximum recommended gross load of the unit. TRACTOR BALLAST Refer to your tractor operator's manual for correct amount of weights or ballast to be used with towed vehicles. Before towing unit(s), use a tow vehicle with the gross weight equal to, or greater than the gross weight of all the equipment being pulled. TRACTOR DRAWBAR Before attaching the RUNNING GEAR to any tractor drawbar, be sure the drawbar is pinned and locked on center and the drawbar pin is a safety lock pin of proper size. TRANSPORT CHAIN Secure the transport chain to the RUNNING GEAR tongue and to the tractor drawbar before transporting. When pulling several units, secure with a transport chain between each unit. CHECKING WHEEL BOLTS Wheel bolts must be tightened after the wagon has been in use a short time and should be checked periodically thereafter to ensure they are tightened to torque chart. CHECKING CHASSIS Periodically, check all bolts and connections, especially before operating on the highway. Looseness in the reach, steering mechanism, or coupling pole may cause the RUNNING GEAR to sway or whip, repair or replace any worn or damaged components immediately. TIRE INFLATION Be sure the tires are inflated to the recommended pressure per tire manufacturers specifications. LOAD DISTRIBUTION Be sure the load is well balanced on the RUNNING GEAR to insure proper trailing. Poor load distribution will cause improper trailing of the wagon. For best trailing results, the load must be evenly distributed between the front and rear axles and between the lefthand and right-hand sides. ADJUSTABLE QUICK HITCH TONGUE The adjustable quick hitch tongue permits the RUNNING GEAR to be hooked-up to the tractor safely. Position the tractor in-front of the RUNNING GEAR. Lift the tongue and extended body to attach the tractor drawbar. Back the tractor up to the re-latch tongue. TONGUE LENGTH For 80, 100, and 120 model Running Gears, to adjust the tongue length, simply lift up on tongue latch handle and extend completely. See Fig. 3-4, page 13. For the 130 model Running Gear, adjust the tongue length by lifting up on the latch handle and extending inner body to desired length. Remove the capscrew and stop nut securing the latch handle to the inner tongue body, move latch handle into new hole location and replace hardware to attain desired length. ADJUSTING WHEELBASE To adjust wheelbase, remove the capscrews, (flatwashers), and stop nuts, holding the coupling pole to the axle frames. Slide the coupling pole / axle frames to the desired setting. Replace hardware and tighten. -6-
OPERATIONS TRANSPORT CHAIN NOTE: Select transport chain based on gross weight being towed, adding total of all wagons. NOTE: When towing two wagons, wrap the chain of second wagon around the rear axle of the first wagon and secure. Allowing no more slack than necessary, attach transport chain by inserting chain link between underside lugs on tongue and attach using pin (108049) and secure with two spiral pins (91144-167). Use only pin provided. Use intermediate support, see Fig. 1-2. Do not use the intermediate support as the attaching point. Store transport chain by wrapping or laying on tongue, not allowing chain to rest on ground. Chain is more sensitive to rusting or pitting and should be inspected prior to each use. Do not weld or attempt to repair chain, chain must be replaced. Intermediate Support Towing Machine FIG. 1-1 FIG. 1-2 OM03377A Towed Machine Attaching Point Please contact your dealer for pricing and availablility on the following transport chains. PART NO. 97455 97456 97457 97458 97459 DESCRIPTION Transport Chain Bundle Transport Chain Bundle Transport Chain Bundle Transport Chain Bundle Transport Chain Bundle CAPACITY 16,100 lbs. Maximum Gross Load 20,200 lbs. Maximum Gross Load 30,400 lbs. Maximum Gross Load 40,500 lbs. Maximum Gross Load 60,600 lbs. Maximum Gross Load -7-
SERVICE SECTION II SERVICE ADJUSTING WHEEL TOE-IN FIG. 2-1 IMPORTANT: After first use, recheck toe-in. Front wheel toe-in has been preset at the factory. If adjustment becomes necessary, use the following procedure. 1. Place the tongue in a straight and horizontal position. This can be checked by measuring reference lines "A" and "B". These measurements are the same when the tongue is straight forward. OM-00221A 3. If not, loosen both nuts on each tie rod and turn the tie rod to increase or decrease its length. When desired adjustment is reached, tighten nuts on tie rods. NOTE: Tie rods must be adjusted equally, so that dimension "C" is the same on both sides. 2. Measure the distance between the front wheels at the centerline of the tires, Front (F) and Rear (R). Measurement "R" should be 1/8" to 3/8" longer than measurement "F" for proper toe-in. -8-
SERVICE MAINTENANCE INSTRUCTIONS For running gear and bearing longevity, as well as ease of operation, periodic lubrication is essential. This also helps to flush out moisture and dirt. GREASE GUN LUBE POINTS Tongue Hitch Pin (End of Steering Hinge) - 1 Point Steering Hinge Pin (Front of Front Frame) - 1 Point Spindle Bearings (Both Ends of Front Axle) - 2 Points LUBE CYCLE Grease Once/Year Grease Once/Year Grease Once/Year MISCELLANEOUS LUBE POINTS Extension Part of Extendable Tongue Wheel Bearing - 8 Points Oil or Grease When Needed Repack Grease Yearly After first use: 1. Recheck toe-in. Tie rods -- adjust to minimum 1/8" toe in (1/8" to 3/8" toe measured at tires). Periodically during usage, check the following: 1. Tongue pivot pin. 2. Tie rod connections at radius arm and at steering hinge. 3. Coupling pole bolt and nuts. 4. Tire pressure -- follow manufacturer's specification (too high or too low pressure causes abnormal tread wear). 5. Beveled wheel bolts -- torque to 112 ft. lbs. After each season: 1. Check welds on front and rear axles to coupling pole and to hounds. 2. Tie rods -- adjust to minimum 1/8" toe in (1/8" to 3/8" toe measured at tires). 3. It is recommended for improved tire life that tires be rotated diagonally. NOTE: It is recommended that gravity boxes used with this gear be bolted through front stakes only. For applications involving extensive road travel, it is recommended to bolt 4 corners. CAUTION! WHEN MOUNTING GRAVITY GRAIN BOX TO WAGON, ALL FOUR CORNERS OF BOX SHOULD BE BOLTED TO GEAR. FAILURE TO COMPLY MAY RESULT IN DAMAGE TO BOX OR GEAR. CAUTION! THIS RUNNING GEAR IS DESIGNED FOR AGRICULTURAL USE AND SHOULD NOT BE TOWED IN EXCESS OF 20 M.P.H. SLIDING HITCH AND LATCH The braking system on your running gear is designed to release automatically when you back-up. Before adjusting individual brake shoes, inspect the master cylinder push plate and put tube adjustment screw for proper contact when the sliding hitch and latch mechanism are compressed. If necessary, adjust the setscrew for a 1/4" gap in the normal free position (Fig. 2-2). Be sure to retighten jam nut. BRAKE SYSTEM FIG. 2-2 OM-02896-9-
SERVICE WARNING! SALTWATER, GRANULAR FERTILIZERS, AND OTHER CORROSIVE MA- TERIALS ARE DESTRUCTIVE TO METAL. TO PRO- LONG THE LIFE OF A BRAKING SYSTEM USED UN- DER CORROSIVE CONDITIONS, FLUSH THE ACTUA- TOR PERIODICALLY WITH A HIGH PRESSURE WA- TER HOSE. BE SURE TO GREASE BEARINGS AND OIL ALL MOVING PARTS AFTER THE UNIT HAS DRIED. AT THE END OF THE SEASON, WHEN UNIT IS TO BE STORED, REMOVE THE BRAKE DRUMS AND CLEAN INSIDE THE BRAKES. PACK THE WHEEL BEARING BEFORE DRUM IS INSTALLED. CAUTION! DO NOT PACK HUB FULL OF GREASE. EXCESSIVE GREASE MAY LEAK INTO BRAKE DRUMS CAUSING BRAKE FAIL- URE. MASTER CYLINDER Brake fluid level may be checked by removing the cap on the master cylinder. Refill level with a heavy-duty brake fluid that meets or exceeds DOT-3. Do not clean any brake components in gasoline, kerosene, or oil. BRAKE SHOE ADJUSTMENT Brakes are set at the factory, however, it may become necessary to adjust shoes after first season. The brakes incorporate a "Back-up" feature that makes it necessary to rotate the wheels in the direction of forward rotation only when making adjustments. Jack-up each wheel, turn adjustment cog wheel located in slot on the brake backing plate until you cannot rotate the wheel by hand, then backoff the adjustment 1-1/2 turns (20 cogs/ notches). NOTE: Always rotate drum in direction of forward rotation only. IMPORTANT: Maintain brake fluid level in master cylinder. Adjust brake shoes as necessary. Purge air from lines if necessary. BRAKE BLEEDING Use ONLY quality DOT-3 heavy-duty brake fluid. If pressure bleeding equipment is available follow the manufacturer's instructions in bleeding the system. MANUAL BLEEDING Fill master cylinder with fluid. Bleed brakes first (farthest from master cylinder). Loosen the bleeder screw located in wheel cylinder one turn. The system is now open to the atmosphere through a passage drilled in the screw. Securely install bleeder hose to bleed screw on first wheel cylinder to be bled. TORQUE CHART CAPSCREWS - GRADE 5 NOTE: Grade 5 capscrews can be identified by three radial dashes on head. -10- SIZE 1/4-20 1/4-28 5/16-18 5/16-24 3/8-16 3/8-24 7/16-14 7/16-20 1/2-13 1/2-20 9/16-12 9/16-18 5/8-11 5/8-18 3/4-10 3/4-16 7/8-9 7/8-14 FOOT POUNDS 11 13 21 23 38 40 55 60 85 95 125 140 175 210 300 330 450 490 NEWTON METERS 15 18 28 31 52 54 75 81 115 129 170 190 237 285 407 447 610 664
NOTES NOTES -11-
ASSEMBLY SECTION III ASSEMBLY ASSEMBLY INSTRUCTIONS (MODELS WITHOUT BRAKES) 12 TON SHOWN FIG. 3-1 OM-03927 WARNING! MUST HAVE A MINIMUM OF TWO BOLTS ENGAGED PER END OF COUPLING POLE. FAILURE TO DO SO COULD RESULT IN FAILURE OF GEAR. 1. Determine the desired length of the gear. 2. Insert coupling pole into the front and rear frames. 3. Align holes in frames with the holes in the coupling pole which best fits the undercarriage on your gravity box. 4. Secure the coupling pole to both frames using the hardware provided with you model running gear. 5. Position the stake pockets onto both the front and rear frames. Place the stake pockets against the outside of each runner on the undercarriage of your gravity box. Secure with hardware provided. NOTE: The stake pocket can be set at either of 2 widths (38" or 42" Inside). Set at the width that matches your gravity box skid width. FIG. 3-2 OM-03928-12-
ASSEMBLY FIG. 3-3 OM-03929 6. Fasten the tongue assembly onto the turning plate on the front frame using the pin weldment and hardware provided for your model running gear. 7. Hoist unit and install the tire and wheel assemblies onto hubs. Torque bolts to 112 ft. lbs. NOTE: The quick hitch tongue is adjustable to a variety of lengths. Relocate latch to the required position and re-install pin. Be sure to install hair pin cotter to prevent any inadvertent removal of pin. ADJUSTABLE TONGUE LENGTH FIG. 3-4 Remove hair pin cotter and hitch pin from latch handle. Lift the latch handle and extend the inner body to desired location. Replace the hitch pin and hair pin cotter. -13-
ASSEMBLY NOTE: If your unit is shipped to you unassembled, follow these instructions. 1. Determine the desired length of the gear. 2. Insert the reach tube (3773) inside the front or the rear assembly. Secure the reach tube with four 5/8-11 x 1 3/4" lg. capscrews (9390-123), eight 5/8" flatwashers (9405-100) and four 5/8-11 elastic stop nuts (9398-019). 3. Assemble the other side in the same way. NOTE: Be sure the reach tube is the same distance in the front frame assembly as the rear frame assembly. 4. Uncoil the 3/16" dia. x 120" lg. brake line (96725) from the front gear assembly and attach the end to the 3/16" tee (9465) on the rear assembly. ASSEMBLY INSTRUCTIONS (13 TON MODEL WITH BRAKES) 5. Attach the brake line clip (96728) to the 120" lg. brake line, secure with a 1/4-20 x 1 1/2" lg. capscrew (9390-007), two 3/ 8" flatwashers (9405-0760 and a 1/4-20 locknut (9936). NOTE: The 3/8" flatwashers should be assembled against the reach tube. NOTE: A loop may need to be put in the brake line depending on the length of the running gear. NOTE: Refer to the "Torque Chart" when tightening all hardware and brake lines. FIG. 3-5 OM-02868-14-
6. Use a minimum 300 lb. hoist to lift the tongue assembly into position. 7. Insert pin (30170) and secure with the elastic stop nut (9397-020). TONGUE ASSEMBLY ASSEMBLY NOTE: The counterbalance spring is provided as an aid in lifting and holding the tongue, and should not be adjusted so tight, that the tongue is held up horizontally or above. Remember to tighten lugnuts. NOTE: Refer to the "Torque Chart". 8. Attach the hydraulic brake hose (96723) to the brake line and then to the master cylinder. 9. Attach the wheels onto the gear and secure with 9/16-18 tapered nuts (91158) onto the studs, torque to 112 ft. lbs. NOTE: Decal on the breather cap of master cylinder must be removed prior to using the brake system. FIG. 3-6 OM-02756-15-
PARTS SECTION IV PARTS MODEL #80 PARTS OM-03879 REVISED 102804-1 -16-
PARTS ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 PART NO. 30711B 100009B 9168 91816 9165 95555 9163 9162B 9391-034 100035 30638B 105806B 9390-067 9405-076 9928 97632 101577B 9389-124 9398-019 91605 91072 30633B 9390-055 9404-021 100004 100003 93415 101139B 101138B 91160 30402B 30852B 106920 9397-018 9405-112 96976-036 30714B 101136B 100181B 100182B 100183 100184 9391-023 9393-012 100085 101153B 101158B 103842B 3017B 9388-024 9404-019 9394-004 9806 9094 108047 91144-166 97575 9003126 97626 97455 W615-6 W815-6-08 MODEL #80 PARTS DESCRIPTION Hub Complete Hub with Cups, Bolts & Nuts Seal 1 3/4" Bearing 1 3/8" Bearing 1 1/4" Spindle Washer.809 Spindle Nut 3/4-16 Hub Cap Cotter Pin 5/32 x 1 1/4" Lg. Spindle 1 3/4 x 10 Rear Frame Weldment Stake Pocket (Standard) Capscrew 3/8-16 x 4" Lg. Flatwasher 3/8" USS Locknut 3/8-16 (Centerline) Decal, "Parker" Coupling Pole Assembly Capscrew 5/8-11 x 1 1/2" Lg. 5/8" Elastic Stop Nut Decal, "FEMA/Member Farm" Decal, "CAUTION" Front Frame Weldment Capscrew 3/8-16 x 1" Lg. Lockwasher 3/8" Cover Washer Wear Washer 2 1/2" 1/4"-28 Self Tapping Zerk Left Front Spindle Right Front Spindle 1/4"-28 Self Tapping Zerk Hitch Pin Weldment Turning Plate Pin Weldment 1"D x 11 5/16 Elastic Jam Nut 1-14 Flatwasher 7/8" USS Locknut 7/8-14 Tie Rod 27 3/16" Assembly Tie Rod LH Knuckle Joint RH Knuckle Joint LH Jam Nut 11/16-18 RH Jam Nut 11/16-18 Cotter Pin 1/8 x 1" Lg. Slotted Nut 9/16-20 Rubber Boot Adjustable Quick Hitch Tongue Assembly Tongue Latch Assembly Detent Latch Weldment Spring.05 x 2 1/2 x 4 Carriage Bolt 5/16-18 x 3/4 Lockwasher 5/16" Hex Nut 5/16-18 UNC Hairpin.148D x 2 11/16 Lg. Clevis Pin 3/4 x 5 Pin 1 1/4D x 3 3/4 Spiral Pin 1/4D x 2 Decal, "CAUTION" Reflector 2 x 9 (Red) Decal, "80" Transport Chain (Optional) 6 x 15 Wheel 8 x 15 Wheel -17- REVISED 102804-1
PARTS MODEL #100 PARTS OM-03879-18-
ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 PART NO. 30712B 9233B 9355 9247 95547 9165 95555 9163 9162B 100076 9391-034 30620B 97632 105806B 9390-067 9928 9405-076 101577B 9389-124 9398-019 91072 91605 30612B 9390-055 9404-021 100054 95548 93415 100070B 100052B 30618B 30402B 106920 9397-018 9405-112 96976-036 30713B 100061B 95550B 95549B 95552 95551 9391-023 9393-014 100085 91160 101153B 101158B 103842B 3017B 9388-024 9404-019 9394-004 9806 9094 108047 91144-166 97575 9003126 97627 97456 W815-6-8 W1015-6-09 W820-6 101594A 101595A MODEL #100 PARTS DESCRIPTION Hub Complete Hub 6 Bolt with Cups Seal 2 1/4" Bearing 1 5/8 Hub Bolt 9/16-18 x 15/16" Lg. Bearing 1 1/4" Spindle Washer.809 Spindle Nut 3/4-16 Hub Cap Spindle 2 1/4D x 11 Cotter Pin 5/32 x 1 1/4" Lg. Rear Frame Weldment Decal, "Parker" Stake Pocket (Standard) Capscrew 3/8-16 x 4" Lg. Locknut 3/8-16 (Centerline) Flatwasher 3/8" USS Coupling Pole Assembly Capscrew 5/8-11 x 1 1/2" Lg. 5/8" Elastic Stop Nut Decal, "CAUTION" Decal, "FEMA/Member Farm" Front Frame Weldment Capscrew 3/8-16 x 1" Lg. Lockwasher 3/8" Cover Washer Wear Washer 2 1/4" 1/4"-28 Self Tapping Zerk Left Front Spindle Right Front Spindle Turning Plate Hitch Pin Weldment Pin Weldment 1"D x 11 5/16 Elastic Jam Nut 1-14 Flatwasher 7/8" USS Locknut 7/8-14 Tie Rod 25 1/8" Assembly Tie Rod RH Knuckle Joint LH Knuckle Joint RH Jam Nut 7/8-18 LH Jam Nut 7/8-18 Cotter Pin 1/8 x 1" Lg. Slotted Nut 5/8-18 Rubber Boot 1/4"-28 Self Tapping Zerk Adjustable Quick Hitch Tongue Assembly Tongue Latch Assembly Detent Latch Weldment Spring.05 x 2 1/2 x 4 Carriage Bolt 5/16-18 x 3/4 Lockwasher 5/16" Hex Nut 5/16-18 UNC Hairpin.148D x 2 11/16 Lg. Clevis Pin 3/4 x 5 Pin 1 1/4D x 3 3/4 Spiral Pin 1/4D x 2 Decal, "CAUTION" Reflector 2 x 9 (Red) Decal, "100" Transport Chain (Optional) 8 x 15 Wheel 10 x 15 Wheel 8 x 20 Wheel Complete Front Frame Assembly Complete Rear Frame Assembly -19- PARTS
PARTS MODEL #120 PARTS OM-03879-20-
MODEL #120 PARTS PARTS ITEM 1 10 11 12 13 14 15 16 17 18 19 20 21 22 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 51 52 58 59 60 61 62 63 64 2 3 4 5 6 7 8 9 23 24 25 44 45 46 47 48 49 50 53 54 55 56 57 PART NO. 30710B 95546B 9355 9353 9354 95547 9345 9165 95555 9163 9391-034 9162B 100047 107506B 105806B 9928 9405-076 9390-067 97628 97632 9003126 100206B 9390-143 9398-021 9390-145 91072 91605 30604B 9390-055 9404-021 100054B 95548 93415 100072B 100071B 91238 91160 30170 30606B 106920 9397-018 9397-019 30709B 100084B 95550B 95549B 9393-014 9391-023 95552 95551 101153B 101158B 103842B 3017B 9388-024 9404-019 9394-004 9806 9094 108047 91144-166 97575 97457 97459 100087 W1116.1-8-60 W820-8 W8.2522.5-8 DESCRIPTION Hub Complete Hub with Cups Seal 2 1/4" Bearing 1 25/32" Cup 1 25/32" Hub Bolt 9/16-18 x 15/16" Lg. Cup 1 1/4" Bearing 1 1/4" Spindle Washer.809 Spindle Nut 3/4-16 Cotter Pin 5/32 x 1 1/4" Lg. Hub Cap Rear Spindle (ONLY) 12 Ton Rear Frame Stake Pocket (Standard) Locknut 3/8-16 (Centerline) Flatwasher 3/8" Capscrew 3/8-16 x 4" Lg. Decal, "120" Decal, "Parker" Reflector 2 x 9 (Red) Coupling Pole 6' Lg. Capscrew 3/4-10 x 1 1/2" Lg. 3/4" Elastic Stop Nut Capscrew 3/4-10 x 2" Lg. Decal, "CAUTION" Decal, "FEMA/Member Farm" Front Frame Weldment Capscrew 3/8-16 x 1" Lg. Lockwasher 3/8" Cover Washer Wear Washer 2 1/4" 1/4"-28 Self Tapping Zerk Left Front Spindle Right Front Spindle Bearing 1 1/4" 1/4"-28 Self Tapping Zerk Hitch Pin Weldment Turning Plate Pin Weldment 1"D x 11 5/16 Elastic Jam Nut 1-14 Elastic Jam Nut 1 1/8-12 Tie Rod 28" Assembly Tie Rod RH Knuckle Joint LH Knuckle Joint Slotted Nut 5/8-18 Cotter Pin 1/8 x 1" Lg. RH Jam Nut 7/8-18 LH Jam Nut 7/8-18 Adjustable Quick Hitch Tongue Assembly Tongue Latch Assembly Detent Latch Weldment Spring.05 x 2 1/2 x 4 Carriage Bolt 5/16-18 x 3/4 Lock Washer 5/16 Hex Nut 5/16-18 UNC Hairpin.148D x 2 11/16 Lg. Clevis Pin 3/4 x 5 Pin 1 1/4D x 3 3/4 Spiral Pin 1/4D x 2 Decal, "CAUTION" Transport Chain (30,400) Optional Transport Chain (60,600) Optional 10 x 16 Wheel 11 x 16 Wheel 8 x 20 Wheel 8.25 x 22.5 Wheel -21-
PARTS MODEL #130 PARTS Note: For added clearance under the door, a bolster add on kit (#30147) is available. This kit will raise your gravity box off your running gear (approx. 5") where added height is needed. Contact your dealer for more information. -22- OM-03879
MODEL #130 PARTS PARTS ITEM 1 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 33 34 35 36 37 38 39 40 41 42 43 44 45 49 55 56 57 58 59 60 61 62 63 64 65 2 3 4 5 6 7 24 25 26 27 28 29 30 31 32 46 47 48 50 51 52 53 54 PART NO. 3720B 91146 91149 91154 91155 91156 91157 30165 30168B 30170 30172 3635B 3636B 3650B 91147 91158 91160 91213 9391-036 9397-019 9397-022 9405-130 9582B 9390-329 9393-066 9394-009 9404-025 9681B 9682 9683B 9684B 9685B 9391-024 91072 91605 3676 9390-092 94980 3677 97629 3673B 9390-123 9398-019 9405-100 107891B 101156 101369 107890 101158B 103842B 3017B 9388-024 9394-004 9404-019 108047 91144-166 3702B 91247 9395-014 9390-099 9390-156 9398-021 97632 97457 W1116.1-8-60 W820-8 W8.2522.5-8 97170 W8.2524.5-8 DESCRIPTION Hub Assembly Flatwasher 7/8" Hub 8 Bolt with Cups & Studs Bearing (2.00 Bore) Bearing (1.3125 Bore) Hub Cap Seal Trunnion Pin Steering Hitch Weldment Hitch Pin Weldment Washer Spindle Weldment Right-Hand Spindle Weldment Left-Hand Front Frame Weldment Slotted Nut 7/8-14 Wheel Nut 9/16-18 Grease Zerk Thrust Washer Cotter Pin 5/32" x 1 3/4" Elastic Stop Nut 1 1/8" Elastic Stop Nut 1 1/2" Flatwasher 1 1/4" Tie Rod Assembly Capscrew 1/2-20 x 2 1/2" (Gr. 5) Slotted Nut 5/8-18 Hex Nut 1/2-20 (Gr. 5) Lockwasher 1/2" Tie Rod Tube Rod End Seal Tube Clamp Tapered Tie Rod End Left-Hand Tapered Tie Rod End Right-Hand Cotter Pin 1/8" x 1 1/4" Decal, CAUTION... Decal, FEMA Stake Pocket Capscrew 7/16-14 x 5" (Gr. 5) Elastic Stop Nut 7/16" Rear Frame Weldment Decal, #130 Reach Tube Capscrew 5/8-11 x 1 3/4" (Gr. 5) Elastic Stop Nut 5/8" Flatwasher 5/8" Extendible Tongue (Complete 107892BE) Tongue Extension Detent Stop Toungue Outer Body Tongue Latch Assembly Detent Latch Weldment Spring Carriage Bolt 5/16-18 x 3/4" (Gr. 5) Hex Nut 5/16-18 (Gr. 5) Lockwasher 5/16" Pin 1 1/4" x 3 3/4" Spiral Pin 1/4" x 2" Spring Set Screw 5/8-11 x 1 3/4" Hex Jam Nut 5/8-11 (Gr. 5) Capscrew 1/2-13 x 1" (Gr. 5) Capscrew 3/4-10 x 5 1/2" (Gr. 5) Elastic Stop Nut 3/4" Decal, PARKER Transport Chain Optional 16.1 x 11 Wheel 20 x 8 Wheel 22.5 x 8.25 Wheel 22.5 x 11.25 Wheel 24.5 x 8.25 Wheel -23-
PARTS MODEL #130B PARTS OM-03879-24-
MODEL #130B PARTS PARTS ITEM 1 2 3 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 4 5 6 10 11 12 7 8 9 PART NO. 30342B 9001963B 3720B 91157 91154 91149 91151 91150 91152 91155 91156 91146 91153 91158 91147 9391-036 30339B 97630 3635B 3636B 3650B 30165 30168 30170 30172 91072 91160 91213 91605 9391-024 9397-019 9397-022 9405-130 9582B 9393-066 9682 9685B 9390-329 9683B 9681B 9684B 9394-009 9404-025 3673B 9390-123 9405-100 9398-019 9464 9465 9807 9936 30344 30345 96723 96725 96726 96728 9390-007 9390-019 9390-028 9405-064 9405-076 97632 97457 DESCRIPTION Hub Assembly Brake Drum 13" Hub Subassembly Seal Bearing Hub 8 Bolt Subassembly w/cups Bearing Cup #3720 Hub Casting Bearing Cup #2720 Bearing Hub Cap Flatwasher 7/8" Stud Bolt 9/16-18 x 2 1/8" Wheel Nut 9/16-18 Slotted Nut 9/16-18 Cotter Pin 5/32" x 1 3/4" Rear Frame Weldment Decal, #130B Yoke & Spindle Weld't (Right-Hand) Yoke & Spindle Weld't (Left-Hand) Front Frame Weldment Trunnion Pin Weldment Steering Hitch Weldment Hitch Pin Washer 3" x 3" x 3/8" Decal, CAUTION... Grease Zerk Thrust Washer Decal, FEMA Cotter Pin 1/8" x 1 1/4" Elastic Stop Nut 1 1/8" Elastic Stop Nut 1 1/2" Flatwasher 1 1/4" Tie Rod Assembly Slotted Nut 5/8-18 Rod End Seal Tapered Tie Rod End (Right-Hand) Capscrew 1/2-20 x 2 1/2" (Gr. 5) Tube Clamp Tie Rod Tube Tapered Tie Rod End (Left-Hand) Hex Nut 1/2-20 (Gr. 5) Lockwasher 1/2" Reach Tube Capscrew 5/8-11 x 1 3/4" (Gr. 5) Flatwasher 5/8" Elastic Stop Nut 5/8" Clip (Brake Hose) Tee Locknut 5/16-18 Locknut 1/4-20 Bracket Bracket Brake Hose (24") Brake Line Tube 3/16" x 120" Lg. Brake Line Tube 3/16" x 40" Lg. Clip (Brake Line) Capscrew 1/4-20 x 1 1/2" Lg. Capscrew 1/4-20 x 4 1/2" Lg. Capscrw 5/16-18 x 3/4" Lg. Flatwasher 1/4" Flatwasher 3/8" Decal, PARKER Transport Chain (Optional) -25-
PARTS TONGUE WITH BRAKE COMPONENTS ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 PART NO. 3702* 30354* 3017B 30353* 9388-024 9394-004 9404-019 3715* 9512 30326* 30327 30329* 30330* 30334* 30350* 91125 91247 91248 91667* 103886* 9390-124 9390-143 PART NO. Spring Counter Balance Latch Assembly Spring Latch Latch Carriage Bolt 5/16-18 x 3/4" Hex Nut 5/16-18 Lockwasher 5/16" Stop Block Self-Tapping Screw 1/4 x 1" Main Tongue Weldment Pin 5/8" Dia. x 5 1/2" Platic U-Channel Plunger Weldment Inner Tongue Weldment Cover Weldment Clevis Pin 1" x 7" Oval Point Set Screw 1 3/4" Dog Point Set Screw 1 3/4" Shock Absorber (Damper) Tension Spring Capscrew 5/8-11 x 2" Capscrew 3/4-10 x 1 3/4" ITEM 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39-26- PART NO. 9391-058 9395-014 9404-033 92968B 91670B 9003931 91672 91673 91679 9003774 91680 92540 9390-063 9394-006 9404-021 9390-026 97575 9392-142 108047 PART NO. Cotter Pin 1 3/4" Hex Head Jam Nut 5/8-11 Lockwasher 3/4" Master Cylinder w/bracket Master Cylinder (prior to SNA41560000) Spring Bracket (Right) Spring Bracket (Left) Connector w/orifice (prior to SNA41560000) Washer (Brass) (prior to SNA41560000) Fill Cap Capscrew 3/8-16 x 3" Hex Nut 3/8-16 Lockwasher 3/8" Capscrew 5/16-18 x 1/2" Decal, CAUTION... Roll Pin Pin
BRAKE COMPONENTS PARTS ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PART NO. 91609* 91610* 91611 91612* 91613 91614 91615 91616 91617 91618 91619 91620 91621 91622 91623 91624 W615-6 W815-6-08 W1015-6-09 W820-6 100087 W1116.1-8-60 W820-8 W8.2522.5-8 97170 W8.2524.5-8 W11.2522.5-8 PART NO. Back Plate Assembly Front Brake Shoe Assembly Front Shoe Lever Rear Brake Shoe Assembly Wheel Cylinder Assy. (Right) Wheel Cylinder Assy. (Left) Screw & Lockwasher Adjusting Screw Pivot Nut Socket-Adjusting Screw Push Rod-Wheel Cylinder Spring-Adjusting Screw Yellow Spring-Front Lever Red Spring-Rear Shoe Orange Pin-Shoe Hold Down Cup-Shoe Hold Down ITEM 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 WHEELS 15x6" Implement Wheel 15x8" Implement Wheel 15x10" Implement Wheel 20x8" Implement Wheel 16x10" Implement Wheel 16.1x11" Implement Wheel 20x8" Implement Wheel 22.5x8.25" Implement Wheel 22.5x11.25" Implement Wheel 24.5x8.25" Implement Wheel 22.5x11.25" Implement Wheel FOR TIRE WARRANTY Any questions concerning tire warranty should be directed to the tire manufacturer or your local tire dealer. -27- PART NO. 91625 91626 91627 91628 91640 91636 91639 91641 91645 93531 9390-027 9390-323 9394-009 9404-025 91646 PART NO. Spring-Front Hold Down Yellow Spring-Rear Hold Down Black Cover Plate - Adjusting Hole Retaining Ring Truarc Spring Front Shoe Travel Link Pin-Front Shoe (Without Parking Brake) Plug-Plastic Plug-Plastic Hex Locknut 5/16" NC Travel Link Bolt 5/16"NCx5/8" Capscrew 1/2-20 x 1" Hex Nut 1/2-20 Lockwasher 1/2" Wheel Cylinder Repair Kit (8 TON) (8 & 10 TON) (10 TON) (10 TON) (12 TON) (12 & 13 TON) (12 & 13 TON) (12 & 13 TON WITH & WITHOUT BRAKES) (13 TON) (13 TON WITH & WITHOUT BRAKES) (13 TON WITH BRAKES) www.titan-intl.com Phone: 800-USA-BEAR Fax: 515-265-9301 www.firestoneag.com Phone: 800-847-3364
MEMBER FEMA FARM EQUIPMENT MANUFACTURERS ASSOCIATION L:\MANUALS\PARKER\RUNNINGGEARS\\30630.pmd//030404-0/102804-1