Installation Guide Viking Range, LL Front Street Greenwood, Mississippi 890 US (66) 455-00 For product information, call -888-(845-464) or visit the Viking Web site at vikingrange.com Professional Indoor and Outdoor Hoods F87 EN (090)
Table of ontents IMPORTNT Please Read and Follow! Warnings & Important Information -4 VWH 0 H./ H. Wall Hoods w/standard Ventilar 0, & 6 Dimensions & Specifications _ 5 learance Dimensions _ 6 Interior Ventilar Dimensions 7 VWH 8 H. 4 Deep Wall Hoods 0, 6, 4, 48, & 60 Dimensions & Specifications 8 learance Dimensions _ 9 Interior Ventilar Dimensions _ 0 Exterior Ventilar Dimensions _ VWHO 8 H. Outdoor Wall Hoods 6, 48, & 60 Dimensions & Specifications _ learance Dimensions VWH himney Wall Hoods 0, 6, 4, 48, & 60 Dimensions & Specifications _ 4 learance Dimensions 5 Interior Ventilar Dimensions _ 6 Exterior Ventilar Dimensions _ 7 VIH himney Island Hoods 6, 4, 54, & 66 Dimensions & Specifications _ 8 learance Dimensions _ 9 Interior Ventilar Dimensions _ 0 Exterior Ventilar Dimensions _ VV Wall usm Ventilar System Dimensions & Specifications _ Installing Hood anopy _ learance Dimensions _ 4 VV Ventilar Dimensions _ 5 Planning Information 7 Installation Procedures Installation (VWH H. Wall Hoods w/standard Ventilar) 8 Duct over Option (VWH H. Wall Hoods w/standard Ventilar) _ 0 Installation (VWH H. Wall Hoods w/recirculating Kit) _ 0 Installation (VWH 8 H. Wall & VWH himney Wall Hoods) Duct over Option (VWH 8 H. Wall Hoods) _ 4 Duct over Option (VWH himney Wall Hoods) 5 Installation (VIH Island Hoods) 6 Service & Registration _ 8 Wiring Diagram 9 NOTE: If installing hood with warming shelf panel, install warming shelf panel first. IMPORTNT PLESE RED ND FOLLOW efore beginning, please read these instructions completely and carefully. Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty. Please observe all local and national codes and ordinances. If no local codes are applicable, wire in accordance with the National Electrical ode, NSI/NFP 70-latest edition. Damp environment approved models should be installed in a covered non-enclosed area and should be protected from the elements as much as possible. The installer should leave these instructions with the consumer who should retain for local inspecr s use and for future reference. heck with a qualified and trained installer or local codes for makeup air requirement, if any. This hood is for residential installation only and is not designed for installation over a commercial product. Make sure power is off at the main circuit breaker or fuse box before making connections. To avoid risk of fire, electric shock, or injury persons, turn off the electricity the hood from the power supply before servicing or cleaning. Viking hoods are equipped with variable speed control blowers. These units will not function with a single speed ventilar. ll Viking Range ventilar kits are designed specifically for use with Viking Range hoods. Use of any non-viking Range ventilar kit will void the hood warranty. Viking hoods are equipped with the variable speed controls for blowers. These units will not function with a single speed ventilar. ll Viking ventilar kits are designed specifically for use with Viking hoods. Use of any non-viking ventilar kit will void the hood warranty. RED ND SVE THESE INSTRUTIONS WRNING To reduce the risk of fire, electric shock, or injury persons, observe the following: Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer. efore servicing or cleaning unit, switch power off at service panel and lock service panel prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, the service panel. WRNING TO REDUE THE RISK OF FIRE, ELETRIL SHOK, OR INJURY TO PERSONS, OSERVE THE FOLLOWING:. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.. Sufficient air is needed for proper combustion and exhausting of gases through the flute (chimney) of fuel burning equipment prevent back drafting. Follow the heating equipment manufacturer s guideline and safety standards such as those published by the National Fire Protection ssociation (NFP), and the merican Society for Heating, Refrigeration and ir onditioning Engineers (SHRE), and the local code authorities.. When cutting of drilling in wall or ceiling, do not damage electrical wiring and other hidden utilities. 4. Ducted fans must always be vented the outdoors. 5. WRNING!: To reduce risk of fire, use only metal ductwork 6. UTION!: To reduce risk of fire and properly exhaust air, be sure duct air outside. Do not vent exhaust air in spaces within walls or ceilings, or in attics, crawl spaces, or garages. 7. UTION!: To Reduce the Risk of Fire and Electric Shock, Install this rangehood only with remote blower models manufactured by Viking, model numbers DEV900/DEV00, VEV900/VEV00, OR DEV500, VEV500 or integral blowers manufactured by Viking, model numbers DIV00, DIV440, DIV600, DIV800, DIV00, VIV00, VIV600, or VIV00. NOTE Please refer inside for specific canopy/blower combinations.
IMPORTNT Please Read and Follow! Dimensions & Specifications (VWH 0 H./ H. Wall Hoods w/standard Ventilar 0, & 6 ) WRNING To reduce the risk of injury persons in the event of a rangep grease fire, observe the following. (ased on Kitchen Firesafety Tips, published by NFP.) UTION For general ventilating use only. Do not use exhaust hazardous or explosive materials and vapors. (0.5 cm). SMOTHER FLMES with a close fitted lid, cookie sheet, or metal tray, then turn off the burner. E REFUL TO PREVENT URNS. If the flames do not go out immediately, EVUTE ND LL THE FIRE DEPRTMENT.. NEVER PIK UP FLMING PN. You may be burned.. DO NOT USE WTER, including wet dishcloths or wels a violent steam explosion will result. 4. Use an extinguisher ONLY if You know it is a lass extinguisher, and you already know how operate it. The fire is small and contained in the area where it started. The fire department is being called. You can fight the fire with your back an exit. WRNING TO REDUE THE RISK OF FIRE, ELETRIL SHOK, OR INJURY TO PERSONS Rangehoods must be installed with the ventilars that are specified on their carn indicating suitability with this model. Other ventilars cannot be substituted. 5 (.7 cm) (Hood width) 9-7/8 (76. cm) 5-7/8 (9. cm) (5. cm) 0 (5.4 cm) 5 (.7 cm) (0.5 cm) (0.5 cm) (5. cm) (Hood width) 9-7/8 (76. cm) 5-7/8 (9. cm) NOTE: Optional duct cover sold separately. VWH 0 H./ H. Wall Hoods w/standard Ventilar Description 0 6 Duct cover width 9-7/8 (75.9 cm) 5-7/8 (9. cm) Duct cover depth (0.5 cm) Duct cover height (0.5 cm) Number of filters Heat lamps N/ Interior ventilar kit 460 FM Standard Interior duct size* 7 (7.8 cm) Interior Maximum amps 4.9 * Disregard when using recirculating kits. 460 FM blower is shipped with hood. Max duct run is 50 ft (5. m) 4 5
learance Dimensions (VWH 0 H./ H. Wall Hoods w/standard Ventilar) Interior Ventilar Dimensions (VWH 0 H./ H. Wall Hoods w/standard Ventilar) 6 (9.4 cm) 60 min. (5.4 cm) (60.0 cm) 6 max. 4 min. (6.0 cm) (68.6 cm) 7 max.* 4 W. 4 W. 4 W. 4 W. -7/8 (60.6 cm) 9-7/8 (75.9 cm) 5-7/8 (9. cm) 5-/4 (. cm) 8-/4 (0.9 cm) -/4 (8.6 cm) -5/6 (0. cm) 4-5/6 (7.9 cm) 7-5/6 (45.6 cm) D 5/8 (.6 cm) -5/8 (9. cm) 6-5/8 (6.8 cm) 4 (0. cm) 8 (4.6 cm) -4 (.9 cm) 7 (7.8 cm) dia. duct location -7/8 (9.8 cm) D / (. cm) -/ (8.9 cm) Electrical hookup 460 FM Interior Ventilar Installation * NOTE: When installing with a 4 high-shelf, the 7 (68.6 cm) max. dimensions must be used. 6 7
Dimensions & Specifications (VWH 8 H. 4 Deep Wall Hoods 0, 6, 4, 48, & 60 ) learance Dimensions (VWH 8 H. Wall Hoods) (Hood width) 9-7/8 (76. cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 48 W. 47-7/8 (.6 cm) 59-7/8 (5. cm) 6 (5. cm) (0.5 cm) 8 (45.7 cm) 4 (6.0 cm) NOTE: Optional duct cover sold separately. VWH 8 H. Wall Hoods Description 0 6 4 48 60 Duct cover width 9-7/8 (75.9 cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) (0.5 cm) (0.5 cm) 47-7/8 (.6 cm) 59-7/8 (5. cm) Duct cover depth Duct cover height Number of filters 4 Heat lamps 6 (9.4 cm) 66 min. (67.6 cm) (8.9 cm) 7 max. 0 min. (76. cm) (9.4 cm) 6 max. Interior ventilar kits Exterior ventilar kits VINV00/ 600/00 DEV900/ 00* VINV00/ 600/00 DEV900/ 00* VINV600/ 00 DEV900/ 00* VINV00* DEV00*/ 500** VINV00* DEV00*/ 500** In-line ventilar kits DIL00 DIL00 DIL00 DIL00 DIL00 Interior duct size 7 /0 (7.8/5.4 cm) 7 /0 (7.8/5.4 cm) 7 /0 (7.8/5.4 cm) 0 (5.4 cm) 0 (5.4 cm) Exterior duct size 0 (4.5 cm) Interior Maximum amps 4./5./8. 4./5./8. 5./8. 0.8 0.8 Exterior Maximum amps 8.0/5. 8.0/5. 8.0/5. 7.8/8.5 7.8/8.5 In-Line Maximum amps 5./7. 5./7. 5./7. 9.6 0.0 *,00 FM interior- or exterior-power ventilar should be used when installed over range/rangep with gas chargrill. Max duct run is 50 ft (5. m). ** It is recommended that the,500 FM ventilar be used with longer duct runs. Max duct run is 75 ft (.9 m) NOTE: Maximum amp rating for hoods includes recommended ventilar kit rating; ll products must be hard wired with - wire with ground. n interior- or exterior-power ventilar kit must be purchased for installation with all 8 H. hoods. 8 9
Interior Ventilar Dimensions (VWH 8 H. Wall Hoods) Exterior Ventilar Dimensions (VWH 8 H. Wall Hoods) 4-5/6 (7.9 cm) 7-5/6 (45.6 cm) 0-5/6 (5. cm) -5/6 (60.8 cm) 9-5/6 (76.0 cm) 4-5/8 (.7 cm) 9-7/8 (75.9 cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 47-7/8 (.6 cm) 59-7/8 (5. cm) 4-5/6 (7.9 cm) 7-5/6 (45.6 cm) 0-5/6 (5. cm) -5/6 (60.8 cm) 9-5/6 (76.0 cm) 5-5/6 (5. cm) 9-7/8 (75.9 cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 47-7/8 (.6 cm) 59-7/8 (5. cm) 7 (7.8 cm) dia. duct location 0 (5.4 cm) dia. duct location 00 or 600 FM Interior Ventilar Installation for all Wall Hoods 900 or 00 FM Exterior or In-Line Ventilar Installation for all Wall Hoods 4-5/6 (7.9 cm) 7-5/6 (45.6 cm) 0-5/6 (5. cm) -5/6 (60.8 cm) 9-5/6 (76.0 cm) 5-/ (4.0 cm) 0 (5.4 cm) dia. duct location 9-7/8 (75.9 cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 47-7/8 (.6 cm) 59-7/8 (5. cm) 4-5/6 (7.9 cm) 7-5/6 (45.6 cm) 0-5/6 (5. cm) -5/6 (60.8 cm) 9-5/6 (76.0 cm) 5-5/6 (5. cm) 0 (5.4 cm) dia. duct location 9-7/8 (75.9 cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 47-7/8 (.6 cm) 59-7/8 (5. cm) 00 FM Interior Ventilar Installation for all Wall Hoods 00 or 500 FM Exterior or In-Line Ventilar Installation for all Wall Hoods 0
Dimensions & Specifications (VWHO 8 H. Outdoor Wall Hoods 6, 48, & 60 ) learance Dimensions (VWHO 8 H. Outdoor Wall Hoods) Seal joints with silicone. Provided on T Series only. (Hood width) 5-7/8 (9. cm) 48 W. 47-7/8 (.6 cm) 59-7/8 (5. cm) 6 (5. cm) 7 (68.6 cm) (0.5 cm) 8 (45.7 cm) 66 min. (67.6 cm) 7 max. (8.9 cm) 8 (45.7 cm) 7 (68.6 cm) DIM X + 4-/ (.4 cm) 0 min. (76. cm) 6 max. (9.4 cm) NOTE: Optional duct cover sold separately. VWHO 8 H. Outdoor Wall Hoods Description 6 48 60 Duct cover width 5-7/8 (9. cm) 47-7/8 (.6 cm) 59-7/8 (5. cm) Duct cover depth (0.5 cm) Duct cover height (0.5 cm) Number of filters 4 Interior ventilar kits VINV00* VINV00* VINV00* Exterior ventilar kits DEV00*/500** DEV00*/500** DEV00*/500** In-line ventilar kits DIL00 DIL00 DIL00 Interior duct size 0 (5.4 cm) Exterior duct size 0 (5.4 cm) Interior Maximum amps 9.0.4.8 Exterior Maximum amps 6./6.8 8.4/9. 8.8/9.5 In-Line Maximum amps 7.9 0. 0.6 *,00 FM interior- or exterior-power ventilar should be used with all outdoor models and when i ndoor models are installed over range/rangep with gas char-grill. Max duct run is 50 ft (5. m). ** It is recommended that the,500 FM ventilar be used with longer duct runs. Max duct run is 75 ft (.9 m). NOTE: Maximum amp rating for hoods includes recommended ventilar kit rating; ll products must be hard wired with - wire with ground. n interior- or exterior-power ventilar kit must be purchased for installation with all 8 H. hoods. 6 (9.4 cm) Note: Outdoor Models must be installed in a covered, non-enclosed area, and should be protected from the elements as much as possible. The botm of the hood should be 0 (76. cm) 6 (9.4 cm) above the grill surface. The hood should be installed 4-/ (.4 cm) plus the distance between the back trim and surface from the back wall. (Note: There is a minimum clearance from the back trim non-combustible surfaces, and a 4 minimum combustible surfaces.) This will require building the hood out from the wall. ny combustible material used for this purpose must be covered with locally-supplied stainless steel. Viking also recommends using a backsplash.
Dimensions & Specifications (VWH himney Wall Hoods 0, 6, 4, 48, 54, & 60 ) learance Dimensions (VWH himney Wall Hoods) (Duct width) (0.5 cm) (0.5 cm) (0.5 cm) 48 W. 8 (45.7 cm) 4 (6.0 cm) 4 (6.0 cm) (0.5 cm) 4 (Hood width) 9-7/8 (76. cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 48 W. 47-7/8 (.6 cm) 59-7/8 (5. cm) 65-7/8 (67. cm) NOTE: Optional duct cover sold separately. 6 (5. cm) VWH himney Wall Hoods 4 (6.0 cm) Description 0 6 4 48 60 (6.0 cm) 8 (45.7 cm) 66 min. (67.6 cm) (8.9 cm) 7 max. 0 min. (76. cm) (9.4 cm) 6 max. Duct cover width (0.5 cm) (0.5 cm) (0.5 cm) 8 (45.7 cm) 4 (6.0 cm) Duct cover depth Duct cover height (0.5 cm) (0.5 cm) 4 (6.0 cm) Number of filters 6 (9.4 cm) Heat lamps Interior ventilar kits VINV00/600 VINV00/600 VINV600 VINV00* VINV00* Exterior ventilar kits DEV900/ 00* DEV900/ 00* DEV900/ 00* DEV00*/ 500** DEV00*/ 500** In-line ventilar kits DIL00 DIL00 DIL00 DIL00 DIL00 Interior duct size 7 (7.8 cm) 7 (7.8 cm) 7 (7.8 cm) 0 (5.4 cm) 0 (5.4 cm) Exterior duct size 0 (5.4 cm) Interior Maximum amps 4./5. 4./5. 5. 0.8 0.8 Exterior Maximum amps 8.0/5. 8.0/5. 8.0/5. 7.8/8.5 7.8/8.5 In-Line Maximum amps 5./7. 5./7. 5./7. 9.6 0.0 *,00 FM interior- or exterior-power ventilar should be used when installed over range/rangep with gas chargrill. Max duct run is 50 ft (5. m). ** It is recommended that the,500 FM ventilar be used with longer duct runs. Max duct run is 75 ft (.9 m). NOTE: Maximum amp rating for hoods includes recommended ventilar kit rating; ll products must be hard wired with -wire with ground. n interior- or exterior-power ventilar kit must be purchased for installation with all 8 H. hoods. 4 5
Interior Ventilar Dimensions (VWH himney Wall HoodsF Exterior Ventilar Dimensions (VWH himney Wall HoodsF (0.5 cm) -/ (.8 cm) 0V power supply (0.5 cm) -/ (.8 cm) 0V power supply 4-5/6 (7.9 cm) 7-5/6 (45.6 cm) 0-5/6 (5. cm) 8 (0. cm) -/ (.8 cm) 4-5/6 (7.9 cm) 7-5/6 (45.6 cm) 0-5/6 (5. cm) 8 (0. cm) -/ (.8 cm) 9-7/8 (75.9 cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 7 (7.8 cm) dia. duct location 9-7/8 (75.9 cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 0 (5.4 cm) dia. duct location 00 or 600 FM Interior Ventilar Installation for 0, 6, & 4 models 900 or 00 FM Exterior or In-Line Ventilar Installation for 0, 6, & 4 models -/ (.8 cm) 0 V power supply -/ (.8 cm) 0 V power supply -5/6 (60.8 cm) 9-5/6 (76.0 cm) -5/6 (8.7 cm) 6 (5. cm) -/ (.8 cm) 8 (45.7 cm) 4 (6.0 cm) 4 (6.0 cm) -5/6 (60.8 cm) 9-5/6 (76.0 cm) -5/6 (8.7 cm) 6 (5. cm) -/ (.8 cm) 8 (45.7 cm) 4 (6.0 cm) 4 (6.0 cm) 47-7/8 (.6 cm) 59-7/8 (5. cm) 65-7/8 (67. cm) 0 (5.4 cm) dia. duct location 47-7/8 (.6 cm) 59-7/8 (5. cm) 65-7/8 (67. cm) 0 (5.4 cm) dia. duct location 00 FM Interior Ventilar Installation for 48, & 60 models 900, 00 or 500 FM Exterior or In-Line Ventilar Installation for 48, & 60 models 6 7
Dimensions & Specifications (VIH himney Island Hoods 6, 4, 54, & 66 ) learance Dimensions (VIH himney Island Hoods) (Duct width) (0.5 cm) (0.5 cm) 54 W. 8 (45.7 cm) 4 (70.0 cm) 54 W. (Duct height) (0.5 cm) or 4 (6.0 cm) or 6 (9.4 cm) 6 (5. cm) 8 (45.7 cm) (Hood width) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 54 W. 5-7/8 (6.8 cm) 65-7/8 (67. cm) NOTE: Optional duct cover sold separately. 0 (76. cm) VIH himney Island Hoods Description 6 4 54 66 Duct cover width (0.5 cm) (0.5 cm) 8 (45.7 cm) 4 (70.0 cm) Duct cover depth Duct cover height (0.5 cm) (0.5 cm) or 4 (6.0 cm) or 6 (9.4 cm) Number of filters 4 4 6 8 6 (9.4 cm) 66 min. (67.6 cm) (8.9 cm) 7 max. 0 min. (76. cm) (9.4 cm) 6 max. Heat lamps Interior ventilar kits VINV600 VINV600 VINV00* VINV00* Exterior ventilar kits DEV900/00* DEV900/00*/500** DEV00*/500** DEV00*/500** N/ In-line ventilar kits DIL00 DIL00 DIL00 DIL00 Interior duct size 7 (7.8 cm) 7 (7.8 cm) 0 (5.4 cm) 0 (5.4 cm) Exterior duct size 0 (5.4 cm) Interior Maximum amps 4./5./8. 5./8. 8.9 9. Exterior Maximum amps 7.4/4.7 7.4/4.7/5.5 5.6/6.4 6.4/7.4 In-Line Maximum amps 4.7/6.5.9/5.7 7.4 7.4 *,00 FM interior- or exterior-power ventilar should be used when installed over range/rangep with gas chargrill. Max duct run is 50 ft (5. m). ** It is recommended that the,500 FM ventilar be used with longer duct runs. Max duct run is 75 ft (.9 m). NOTE: Maximum amp rating for hoods includes recommended ventilar kit rating; ll products must be hard wired with -wire with ground. n interior or exterior-power ventilar kit must be purchased for installation with all 8 H. hoods. 8 9
Interior Ventilar Dimensions (VIH himney Island HoodsF Exterior Ventilar Dimensions (VIH himney Island HoodsF (0.5 cm) -/8 (.9 cm) (0.5 cm) -/8 (.9 cm) 7-5/6 (45.6 cm) 0-5/6 (5. cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 6 (5. cm) 0 V power supply -/8 (.9 cm) 7-5/6 (45.6 cm) 0-5/6 (5. cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 6 (5. cm) 0 V power supply -/8 (.9 cm) 7 (7.8 cm) dia. duct location 0 (5.4 cm) dia. duct location 600 FM Interior Ventilar Installation for all himney Island Hoods 900 or 00 FM Exterior or In-Line Ventilar Installation for all himney Island Hoods 54 W. 54 W. 54 W. 6-5/6 (68.4 cm) -5/6 (8.7 cm) 5-7/8 (6.8 cm) 65-7/8 (67. cm) 8 (45.7 cm) 4 (6.0 cm) 6 (5. cm) 0 (5.4 cm) dia. duct location -/8 (.9 cm) 0 V power supply -/8 (.9 cm) 54 W. 54 W. 54 W. 6-5/6 (68.4 cm) -5/6 (8.7 cm) 5-7/8 (6.8 cm) 65-7/8 (67. cm) 8 (45.7 cm) 4 (6.0 cm) 6 (5. cm) 0 (5.4 cm) dia. duct location -/8 (.9 cm) 0 V power supply -/8 (.9 cm) 00 FM Interior Ventilar Installation for all himney Island Hoods 900, 00 or 500 FM Exterior or In-Line Ventilar Installation for all himney Island Hoods 0
Dimensions & Specifications (VV Wall usm Ventilar System 6, 4, 48, & 60 ) Installing Hood anopy (usm Hood anopy uutsf * *For best results, center the unit over the burners of the cooking product (front back; right left). * Make sure the back wall of the cusm hood canopy is flush with the cuut so the ventilar system may be mounted as shown on page 5. usm Hood anopy otm uut Dimensions Wall Hoods Description (Hood Width) (Hood Depth) 6 W. -7/6 (84.9 cm) -7/6 (54.5 cm) 4 W. 9-7/6 (00. cm) -7/6 (54.5 cm) 48 W. 45-7/6 (5.4 cm) -7/6 (54.5 cm) 60 W. 57-7/6 (45.9 cm) -7/6 (54.5 cm) VV Wall usm Ventilar System Description 6 4 48 60 Number of filters 4 Heat lamps Interior ventilar kits VINV00/ 600/00* VINV600/ 00* VINV00* VINV00* Exterior ventilar kits DEV900/ 00* DEV900/ 00* DEV00*/ 500** DEV00*/ 500** In-line ventilar kits DIL00 DIL900/00 DIL00 DIL00 Interior duct size 7 /0 7 /0 (7.8/5.4 cm) (7.8/5.4 cm) 0 (5.4 cm) 0 (5.4 cm) Exterior duct size 0 (5.4 Interior Maximum amps 4./5. 0.8 0.8 0.8 Exterior Maximum amps 8.0/5. 8.0/5. 7.8/8.5 7.8/8.5 In-Line Maximum amps 5./7. 5./7. 9.6 0.0 ) Position ventilar system inside of the cusm hood canopy and center it front back and left right. ) otm mounting holes fasten ventilar system botm of cusm hood canopy with the screws provided. uilt-in Ventilar System ) OPTIONL Rear mounting holes fasten ventilar system rear of cusm hood canopy. *,00 FM interior- or exterior-power ventilar should be used when installed over range/rangep with gas chargrill. Max duct run is 50 ft (5. m). ** It is recommended that the,500 FM ventilar be used with longer duct runs. Max duct run is 75 ft (.9 m). NOTE: Maximum amp rating for hoods includes recommended ventilar kit rating; ll products must be hard wired with - wire with ground. n interior- or exterior-power ventilar kit must be purchased for installation with all 8 H. hoods.
learance Dimensions (VV Wall usm Ventilar System) uilt-in Wall usm Ventilar System Dimensions (VV ModelsF -/ (.8 cm) (.54 cm) -/ (.8 cm) 7/8 (. cm) (usm Hood) -/ (9. cm) 7-/4 (4.8 cm) 5/8 (.6 cm) 6 (5. cm) 5/8 (.6 cm) 66 min. (67.6 cm) (8.9 cm) 7 max. 0 min. (76. cm) (9.4 cm) 6 max. -7/8 (55.8 cm) For 900, 00 or 500 FM Exterior or In-Line Ventilar Installation -7/8 (55.8 cm) For 00, 600 or 00 FM Interior Ventilar Installation 6 (9.4 cm) 5-/ (4.0 cm) D 4-5/8 (.7 cm) D 0 (5.4 cm) dia. duct location 7 (7.8 cm) dia. duct location 5/8 (.6 cm) 900 or 00 FM Exterior or In-Line Ventilar Installation 6, 4 W. Models 5/8 (.6 cm) 00 or 600 FM Interior Ventilar Installation 6, 4 W. Models 6 W. 4-/4 (87.0 cm) 4 W. 40-/4 (0. cm) D 6 W. 7-/8 (4.5 cm) 4 W. 0-/8 (5. cm) 4 5
uilt-in Wall usm Ventilar System Dimensions (VV ModelsF Planning Information 5-/ (4.0 cm) 0 (5.4 cm) dia. duct location 5/8 (.6 cm) 00 or 500 FM Exterior or In-Line Ventilar Installation 48, 60 W. Models D Proper installation of ducting is extremely important ensure maximum performance from any ventilation product. ll FMs are based on tests at 0. static pressure: without applying static pressure, FM would be greatly overstated. Straight runs and gradual turns are best; for example, each 90º elbow is equivalent 5-0 feet (.5-.05 cm) of straight run. Never use flexible duct; it creates back pressure/air turbulence and greatly reduces performance. Proper performance is dependent on proper ducting; make sure that a qualified and trained installer is used. heck with a qualified and trained installer or local codes for makeup air requirement, if any. Max. amp rating for hoods includes recommended ventilar kit rating; all products must be hard wired direct with -wire with ground. Roof cap 7 round duct Roof cap 0 round duct 00 or 600 FM single blower interior-power typical ductwork Duct cover or soffit Hood 00 FM single blower interior power typical ductwork Duct cover or soffit 5-/ (4.0 cm) D Plan where the duct work will be located. Install proper-sized duct work, and roof or wall cap for the type of blower you are using. Recommended hood locations for the most common installations are shown. djust your measurements for various heights of ceilings, soffits, cabinets, or ranges/rangeps. heck Framing Exterior blower 0 round duct Hood 900, 00, or 500 FM exterior power typical ductwork 0 (5.4 cm) dia. duct location Duct cover or soffit 5/8 (.6 cm) Hood 00 FM Interior Ventilar Installation 6, 4, 48, 60 W. Models Wall cap Wall Installation exterior power typical ductwork Duct Duct cover or soffit 6 W. 4-/4 (87.0 cm) 4 W. 40-/4 (0. cm) 48 W. 46-/4 (7.5 cm) 60 W. 58-/4 (48.0 cm) D 6 W. 7-/8 (4.5 cm) 4 W. 0-/8 (5. cm) 48 W. -/8 (58.7 cm) 60 W. 9-/8 (74.0 cm) NOTE: ecause of the weight of the hood make sure that the mounting screws are driven in the framing and not just the drywall. It may be necessary drill additional holes in the canopy for proper alignment. Hood NOTE: Wall exhaust must be a minimum of 4 (6.0 cm) from ground. This may vary depending on local codes and geographic location. 6 7
Installation (VWH 0 H./ H. Wall Hoods w/standard Ventilar) 6 5/6 nut driver 5/6 nut driver heck damper for unrestricted movement, adjust if necessary. ttach transition damper. Seal with aluminum tape. UTION: Secure vent hood wall using screws provided. Use additional mounting screws and wall anchors, if necessary. UTION: If not using a duct cover, using screws provided, make sure p mounting screws are secured in soffit or cabinet framing. Use additional mounting screws, if necessary. WRNING 7 RE OR GREEN 8 To reduce the risk of fire, electric shock, or injury persons, observe the following: Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer. efore servicing or cleaning unit, switch power off at service panel and lock service panel prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, the service panel. WHITE WHITE GREEN LK LK Flip hood over and remove electrical box cover. onnect black black, white white, and the green/bare wire under the green screw. NOTE: Housing wiring must be properly installed for wiring be correct when wiring unit. Replace electrical box cover. Make connection breaker box. 4 5 9 0 Insert 6 of electrical wiring through the p of vent hood and secure using wiring restrain. Refer local codes. Slide duct over transition and tape around joint. Slide filter front over front lip. Push filter rear up, then slide back over rear lip. Slide filter front over front lip. Push filter rear up, then slide back over rear lip. 8 9
Duct over Option (VWH 0 H./ H. Wall Hoods w/standard Ventilar) Installation (VWH 0 H./ H. Wall Hoods w/recirculating Kit) 4 ttach with screws and lock washers provided. ttach with screws. Measure distance from ceiling canopy. Slide the duct cover in place and fasten from inside canopy using the sheet metal screws provided. 5 WRNING To reduce the risk of fire, electric shock, or injury persons, observe the following: Installation (VWH H. Wall Hoods w/recirculating Kit) Remove electrical box cover. Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer. efore servicing or cleaning unit, switch power off at service panel and lock service panel prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, the service panel. 6 7 5/6 nut driver Remove damper and discard with transition. Turn recirculating unit upside down. Place vent hood upside down on recirculating unit. Flip hood over. Insert 6 of electrical wiring through the p of vent hood and secure. Refer local codes. UTION: Secure vent hood. Make sure mounting screws are secured in framing. Use additional mounting screws and wall anchors, if necessary. 0
Installation (con t) (VWH 0 H./ H. Wall Hoods w/recirculating Kit) Installation (VWH 8 H. Wall & VWH himney Wall Hoods) 8 RE OR GREEN 9 -/ x /4 (.8 cm) x (.9 cm) wood strip -/6 (4.6 cm) 5/6 nut driver Slot for wood strip 5/6 nut driver WHITE GREEN LK WHITE LK onnect black black, white white, and the green/bare wire under the green screw. NOTE: Housing wiring must be properly installed for wiring be correct when wiring unit. Replace electrical box cover. Make connection breaker box. Measure down -/6 (4.6 cm) from desired height of hood and secure -/ x /4 wood strip (provided locally) wall using screws provided. Use additional mounting screws secure hood wood strip. 0 5/6 nut driver 5/6 nut driver ssemble brackets baffles and insert charcoal filters. Slide filter front over front lip. Push filter rear up, then slide back over rear lip. UTION: Secure vent hood wall using screws provided. Use additional mounting screws and wall anchors, if necessary. 4 UTION: If not using a duct cover, using screws provided, make sure p mounting screws are secured in soffit or cabinet framing use additional mounting screws, if necessary. 5 Slide spacer front over front lip. Push spacer rear up, then slide back over rear lip. Slide filter front over front lip. Push filter rear up, then slide back over rear lip. Slide filter front over front lip. Push filter rear up, then slide back over rear lip. Slide filter front over front lip. Push filter rear up, then slide back over rear lip.
Duct over Option (VWH 8 H. Wall Hoods) Duct over Option (VWH himney Wall Hoods) Measure distance from ceiling canopy. Slide the duct cover in place and fasten from inside canopy using the sheet metal screws provided. Measure distance from ceiling canopy. Tape avoid scratching. 4 To install ventillation kit refer ventillation kit installation instructions. Place duct cover p inside duct cover base and lower until desired height is found. Mark height. Use the retaining nuts and bolts fasten in place and remove tape. Slide the duct cover in place and fasten from inside canopy using the sheet metal screws provided. 4 5
Installation (VIH Island Hoods) Installation (VIH Island Hoods) 4 5/6 nut driver heck framing where cuut will be. NOTE: 00 lb. limit. ut appropriate size hole in ceiling. Either 7 or 0 depending on your specific unit and ventillar kit. Run duct work down botm edge of duct cover/soffit and secure in place. Make sure the duct does not stick down past the cover. ttach canopy duct cover/soffit. Seal p of hood duct with aluminum tape. Mounting options: 5 6 Using duct cover with ceiling mounting bracket. (Option - VIH only) Using threaded rod for additional support. (Option ) ttaching hood directly soffit or duct cover. (Skip step ) ttach duct cover optional ceiling mounting bracket. Slide filter front over front lip. Push filter rear up, then slide back over rear lip. Slide filter front over front lip. Push filter rear up, then slide back over rear lip. 5/6 nut driver To install ventillation kit refer ventillation kit installation instructions. ttach duct cover ceiling. The ceiling bracket can be hidden by using a locally supplied trim. dditional support option. Drill holes in all four corners for threaded rod and run rods from hood ceiling. 6 7
Service & Registration If service is required, call your dealer or authorized service agency. The name of the authorized service agency can be obtained from the dealer or distribur in your area. Have the following information readily available. Model number Serial number Date purchased Name of dealer from whom purchased learly describe the problem that you are having. If you are unable obtain the name of an authorized service agency, or if you continue have service problems, contact Viking Range, LL at-888-(845-464), online at vikingrange.com or write : VIKING RNGE, LL PREFERRED SERVIE Front Street Greenwood, Mississippi 890 US Record the information indicated below. You will need it if service is ever required. The model and serial number for your hood is located behind the baffle filter on the left side panel in the lower right corner. Model no. Serial no. Date of purchase Date installed Dealer s name ddress If service requires installation of parts, use only authorized parts ensure protection under the warranty. THIS MNUL SHOULD REMIN WITH THE HOOD FOR FUTURE REFERENE. 8 9