MODEL 1700, 2200, 2200F & 2500 Rev 08-13 P/N 5004WP PART'S MANUAL An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or M&W (800-446-5158) to obtain a Free copy before operating the equipment. 1020 South Sangamon Ave. Gibson City, Illinois 60936 217-784-4261 2008 Alamo Group Inc.
TO THE OWNER/OPERATOR/DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic failure with possible injury or death.
Parts Section 1 PARTS SECTION
PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number, and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. NOTE: Please refer to The Safety Section in the front of this Manual for the proper Part Number when ordering Replacement Safety Decals. For maximum safety and to guarantee optimum product reliability, always use genuine Alamo Group Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to: M&W 1020 South Sangamon Ave. Gibson City, Illinois 60936 217-784-4561 2008 Alamo Group Inc. Parts Section 2
PART NAME INDEX COIL TINE LEVELER WING CYLINDER (OPTIONAL)... 37 COIL TINE LEVELER 1700 (OPTIONAL) S/N 10077 -CURRENT Rev 09-04... 33 COIL TINE LEVELER 2500 2200 2200F S/N -CURRENT (OPTIONAL)... 35 DISC FRAME 1700 & 2200... 6 DISC GANG Rev 11-04... 16 DISC LIFT CYLINDER... 26 DISC WING LIFT CYLINDER... 29 FOLDING DISC FRAME COMPONENTS 2200F & 2500 Rev 09-04... 8 FOLDING WING COMPONENTS 2200F & 2500 Rev 09-04... 12 FRONT MAINFRAME... 18 HOSE SCHEMATIC... 24 HOSE SCHEMATIC FOLDING WING... 25 HOSE SCHEMATIC OPTIONAL... 38 HUB & SPINDLE... 21 LIGHT KIT PARTS... 22 MAIN AXLE LIFT CYLINDER... 28 REAR MAINFRAME Rev 01-07... 10 RELIEF VALVE... 31 SEQUENCE VALVE... 30 SHANK Rev 11-04... 14 SUPER LINK ASSEMBLY... 32 TONGUE CYLINDER... 27 TONGUE PARTS... 4 TRUNNION ASSEMBLY 1... 19 TRUNNION ASSEMBLY 2... 20 2008 Alamo Group Inc. Parts Section 3
TONGUE PARTS 2008 Alamo Group Inc. Parts Section 4
TONGUE PARTS ITEM PART NO. QTY. DESCRIPTION 1 00000200 2 NUT, 3/4" NC 2 00001800 3 LOCKNUT, 1/2" NC 3 00015800 2 NUT, 3/4" NC TOPLOCK 4 00037100 2 HEX BOLT, 3/4" NC X 2-1/2" PL5 5 00725712 1 PIN, PULL BENT 6 00748823 3 BOLT, 1/2" NC X 1-1/2" PL5 7 00749185 2 FLATWASHER, 1-1/4" 8 63092200 2 HEX 5/16" NC 3-1/2 PL5 9 00773592 6 PIN, SAFETY LOCK LYNCH 10 02962213 2 ADAPTER, HYDRAULIC ELBOW 11 15B1200 2 WASHER, 3/4" 12 165020 1 PIN, COTTER 13 2450129 1 ASSEMBLY, TOP LINK 14 2457104 1 CYLINDER, HYDRAULIC 15 2460244 1 WELDMENT, HITCH PIN 16 2460340 1 WELDMENT, JACK MOUNT 17 2460248 1 WELDMENT, FRONT MAINFRAME 18 2460249 1 WELDMENT, TONGUE 19 2460255 2 WELDMENT, PIN SUPER LINK LOWER 20 2460257 2 WELDMENT, TONGUE PIN 21 2460317 1 WELDMENT, TOPLINK ARM 22 2460318 1 WELDMENT, UPPER CYLINDER PIN 23 2460319 1 WELDMENT, TOP LINK PIN 24 2461153 2 CLAMP, HOSE 25 2461603 1 PLATE, HOSE RETAINER 26 2465500 1 CASTINGS, CLEVIS HITCH 27 2466250 1 CHAIN, SAFETY TOW 28 2468613 1 JACK 29 2471001 1 STOP 30 330812C 1 HEX NUT, SLOTTED, 1-1/4" X 7 PL5 31 35009C 2 LOCKWASHER, 3/4" 32 2468410 2 PLATE,SINGLE COVER TOP 33 2468408 2 CLAMP, 14MM TUBE HALF 34 2468409 2 CLAMP, 20MM TUBE HALF 2008 Alamo Group Inc. Parts Section 5
DISC FRAME 1700 & 2200 2008 Alamo Group Inc. Parts Section 6
DISC FRAME 1700 & 2200 ITEM PART NO. 1700 2200 DESCRIPTION 1 00015800 4 4 LOCKNUT, 3/8" NC 2 00695100 24 24 LOCKNUT5/8" NC 3 00696800 1 1 ADAPTER, HYDRAULIC STRAIGHT 4 00753642 4 4 BOLT, 3/8" NC X 1-1/4" PL5 5 00753753 24 24 HEXBOLT, 5/6" NC x 2 PL8 6 00773592 4 4 PIN, SAFETY LOCK LYNCH 7 02032200 8 8 LOCKWASHER, 1" 8 02782200 8 8 BOLT, 1 NC x 2 PL8 9 02962213 1 1 ADAPTER, HYDRAULIC ELBOW 10 2457103 1 1 CYLINDER, HYDRAULIC 11 2460212 2 - FRONT GANG TUBE WELDMENT 12 2460213 2 - WELDMENT, REAR GANG TUBE 13 2460214-2 WELDMENT, FRONG GANG TUBE 14 2460215-2 WELDMENT, REAR GANG TUBE 15 2460241 2 - WELDMENT, OUTER DISC FRAME 16 2460242-2 WELDMENT, OUTER DISC FRAME 17 2460243 1 1 WELDMENT, MAIN DISC FRAME 18 2460253 1 1 WELDMENT, LIFT CROSSTUBE FRONT 19 2460254 2 2 WELDMENT, LIFT TIE ROD 20 2460263 4 4 WELDMENT, DISC GANG PIN 21 2460284 10 10 WELDMENT, DISC LIFT PIN 22 2460285 1 1 WELDMENT, LIFT CROSSTUBE REAR 23 2460306 4 4 WELDMENT, DISC GANG PIVOT PIN 24 2462600 8 8 BLOCK, ANTI ROTATE 25 380010C 10 10 FLATWASHER 26 49045 10 10 COTTER PIN 27 2461622 4 4 SPACER,DISC GANG PIN 2008 Alamo Group Inc. Parts Section 7
FOLDING DISC FRAME COMPONENTS 2200F & 2500 Rev 09-04 2008 Alamo Group Inc. Parts Section 8
FOLDING DISC FRAME COMPONENTS 2200F & 2500 Rev 09-04 ITEM PART NO. QTY. QTY. DESCRIPTION 2200F 2500 1 2460327 1 - WDMT,LH OUTER DISC WING 2460299-1 WDMT,LH OUTER DISC WING 2 2460305 2 2 WDMT,INNER DISC WING 3 2460320 2 - WDMT,FRONT GANG TUBE 2460300-4 WDMT,FRONT GANG TUBE 4 2460323 2 - WDMT,REAR INNER GANG TUBE 2460302-2 WDMT,INNER REAR GANG TUBE 5 2460321 2 - WDMT,REAR GANG TUBE 6 2460322 2 - WDMT,FRONT INNER GANG TUBE 2460301-2 WDMT,INNER FRONT GANG TUBE 7 2460330 2 2 WDMT,LH WING LIFT LINK 8 1937156 4 4 SPEC. 90DG ELBOW W/RESTRICTOR 9 2467105 2 2 CYLINDER,HYDRAULIC 3-1/2 X 10 10 2460263 8 8 WDMT,DISC GANG PIN 11 2471038 2 2 PLATE,LIFT LINK 12 2462534 6 6 PIN,SHORT DISC WING PIVOT 13 2462535 6 6 PIN,DISC WING PIVOT 14 2462532 2 2 PIN,CYLINDER CLEVIS 15 2460306 8 8 WDMT,DISC GANG PIVOT PIN 16 2462600 16 16 BLOCK,ANTI-ROTATE 17 00773592 8 8 PIN, SAFETY LOCK LYNCH 18 2460329 2 2 WDMT,RH WING LIFT LINK 19 00015800 8 8 NUT,TOPLOCK 3/8NC PLB 20 00695100 24 24 NUT,TOPLOCK 5/8 NC PLB 21 00753642 8 8 HHCS,3/8NC X 1-1/4,ZP,GRD5 22 00753753 24 24 HEXB 5/8 NC 2 PL 8 23 02032200 16 16 LOCKWASHER 1 STD 24 31793H8C 16 16 HEXB 1 NC 2 PL8 25 2460326 1 - WDMT,RH OUTER DISC WING 2460298-1 WDMT,RH OUTER DISC WING 26 15B2000 12 12 WASHER SAE 1 1/4 PLATED 27 00606000 14 14 PIN-COTTER 3/16 X 2 28 15B1600 2 2 WASHER 1 SAE P 29 2461622 8 8 SPACER,DISC GANG TUBE 30 10070000 8 8 BOLT, 1/4" NC x 2-1/2" P 31 02959924 8 8 NUT, 1/4" NC 2008 Alamo Group Inc. Parts Section 9
REAR MAINFRAME Rev 01-07 2008 Alamo Group Inc. Parts Section 10
REAR MAINFRAME Rev 01-07 ITEM PART NO. QTY. DESCRIPTION 2 00037200 24 LOCKNUT, 3/4" NC 3 00725712 2 PIN, PULL BENT 4 00749185 8 WASHER1-1/4" 5 02918600 8 HEXBOLT, 3/4" NC X 2 PL8 6 02962213 4 ADAPTER, HYDRAULIC ELBOW 7 02963646 16 BOLT, 3/4" NC X 2-1/2" PL5 8 02969064 2 BUSHING, SPRING 9 0536800W 8 SEAL 10 2460102 4 ASSEMBLY, HUB & SPINDLE (SEE PG 21 FOR BREAKDOWN) 12 2460328 2 WELDMENT, WHEEL STRUT 13 2460229 2 WELDMENT, TRUNNION 14 2460238 1 WELDMENT, AXLE TORSION 15 2460239 1 WELDMENT, REAR MAINFRAME 16 2460261 2 WELDMENT, 1700 WING 17 2460262 2 WELDMENT, 2200 WING 18 2462500 4 PIN 19 2462510 2 PIN, DEPTH STOP 20 2466000 8 BEARING, GARIOCK 21 2466777 4 SHIELD 22 2467102 2 CYLINDER, HYDRAULIC 23 2467600 4 WHEEL (1700, 2200) 2467601 4 WHEEL, (2500, 2200F) 24 2467801 4 TIRE 25 2471002 2 STOP 26 314017H5C 12 BOLT, 1/2" NC X 4 PL5 27 32905C 12 NUT, 1/2" NC 28 49208 2 COTTER, HAIRPIN 29 TR415 4 VALVE STEM 30 2460136 4 COMPLETE TIRE AND WHEEL ASSY. (1700, 2200) 2460150 4 COMPLETE TIRE AND WHEEL ASSY. (2500, 2200F) 31 2461160 8 CLAMP,SHIELD BACK-UP 32 02959924 8 NUT TOPLOCK 1/4 NC PL8 33 00021400 8 HEXB 1/4 NC X 3/4 PL5 34 4720 4 GREASE FITTING 1/8 SELF TAP 2008 Alamo Group Inc. Parts Section 11
FOLDING WING COMPONENTS 2200F & 2500 Rev 09-08 2008 Alamo Group Inc. Parts Section 12
FOLDING WING COMPONENTS 2200F & 2500 Rev 09-04 ITEM PART NO. QTY. QTY. DESCRIPTION 2200F 2500 1 2460297 1 1 WDMT,LH SHORT V-WING 2 2460325 1 - WDMT,LH FOLDING V-WING * 2460287-1 WDMT,LH V-WING * 2460296 1 1 WDMT,RH SHORT V-WING (NOT SHOWN) * 2460324 1 - WDMT,RH FOLDING V-WING (NOT SHOWN) * 2460286-1 WDMT,RH V-WING (NOT SHOWN) 3 317024H5C 4 4 HEX CAP 3/4-10 X 10 GR.5 4 2460260 2 2 WDMT,MID MOUNT BRACKET 5 2461415 2 2 STRAP,LIGHT MOUNT 6 35009C 4 4 LOCKWASHER 3/4 7 00000200 4 4 NUT 3/4 NC HEX PL 8 2462536 2 2 PIN,V-RIPPER HINGE 9 00015800 4 4 NUT,TOPLOCK 3/8NC PLB 10 00010600 4 4 HEXB 3/8 NC 2 PL5 11 15B1600 6 6 WASHER 1 SAE P 12 2421094 4 4 LINK,SHORT LIFT 13 2421095 2 2 LINK,LONG LIFT 14 2462533 4 4 PIN,LIFT LINK 15 2457104 2 2 CYLINDER,HYDRAULIC 3 X 8 16 1937156 4 4 SPEC. 90DG ELBOW W/RESTRICTOR 17 37107B13 6 6 CLIP-X HAIR PIN 18 2462538 2 2 PIN, LIFT LINK SHAFT 19 2471045 2 2 PLATE,TRANSPORT LOCK 20 2462532 2 2 PIN,CYLINDER CLEVIS 21 00606000 8 8 PIN-COTTER 3/16 X 2 2008 Alamo Group Inc. Parts Section 13
SHANK Rev 11-04 2008 Alamo Group Inc. Parts Section 14
SHANK Rev 11-04 ITEM PART NO. QTY. DESCRIPTION 1 00000200 10 NUT, 3/4" GR8 2 00002700 2 FLATWASHER, 1/2" 3 00037100 2 HEX BOLT, 3/4" X 3" GR8 4 02027400 1 HEX BOLT 5 02962764 2 DECAL, PINCH POINTS 6 15B1600 2 WASHER, 1" 7 15B1400 2 WASHER, 7/8" 8 2430262 1 WELDMENT, PULL ARM PIN 9 2430265 3 WELDMENT, SPRING GUIDE BAR 10 2431106 1 STOP 11 2432300 2 PULL ARM WASHER 12 2432301 2 TOGGLE WASHER 13 2432521 1 TOGGLE PIN 14 2432523 1 PIVOT PIN 15 2435507 1 TOGGLE, INNER 16 2435508 1 TOGGLE, OUTER 17 2435509 2 SPRING END PLUG 18 2437424 2 EXTENSION SPRING 19 2438332 1 DECAL, 8 HOUR GREASE 20 2438403 2 GROOVED PIN 21 2438404 2 SHANK WASHER 22 2450269 1 WELDMENT, CHISEL POINT 23 2460250 1 WELDMENT, SPRING TUBE 24 2460251 1 WELDMENT, PIN 25 2460252 1 WELDMENT, PIN 26 2460282 1* WELDMENT, STRAIGHT POINT 27 2460283 1* WELDMENT, WING POINT 28 2461079 2 PLATE, CENTER MOUNT 29 2461080 2 PLATE, SHANK MOUNT 30 2462030 1 PLATE, TIE 31 2462512 1 SPRING ANCHOR YOKE 32 2462513 1 PIN, ROLLER 33 2464866 2 TUBE, ROLLER 34 2465502 1 MOUNT, SHANK 35 2465503 1 ARM, SHANK PULL 36 2465505 1* WEAR SHIN 37 2465506 1* SHIN-STRAIGHT SHANK WEAR 38 2468350 1* SHANK, AUTO PARABOLIC LONG 39 2468351 1* SHANK, AUTO STRAIGHT 40 300516H5C 2 HEX TAP, 1/2" NC X 4-1/2" PL5 41 31102H5C 1 HEX BOLT, 5/16" NC X 5/8" PL5 42 31103H5C 2 BOLT, 5/16" NC X 5/8" PL5 43 317026H5C AR HEX BOLT (2 CENTER, 3 LH OR RH) - 3/4" X 11" GR8 44 317030H5C AR HEX BOLT (1 LH OR RH) - 3/4" X 13" GR8 45 32905C 1 NUT, 1/2" NC 46 3331210C 1 NYLON INSERT JAM LOCKNUT 47 331212C 2 NYLON INSERT JAM LOCKNUT 48 35002C 1 LOCKWASHER, 5/16" 49 35009C 10 LOCKWASHER, 3/4" 50 420619 1 ROLL PIN 51 420916 1 ROLL PIN 52 45051 5 SELF TAPPING ZERK 53 45053 1 SELF TAPPING ZERK 54 49053 4 COTTER PIN 55 6D9016 2 WHIZLOCKNUT * Optional 2008 Alamo Group Inc. Parts Section 15
DISC GANG Rev 11-04 2008 Alamo Group Inc. Parts Section 16
DISC GANG Rev 11-04 ITEM PART NO. 1700 2200, 2200F 2500 DESCRIPTION 2 2435501 10 10 12 3 2460446 12 16 18 4 2438362 22 30 34 2468352 22 30 34 5 2460447 12 16 18 6 2431150 4 8 8 7 2436500 4 8 8 8 2436510 4 8 8 9 2437500 12 16 18 10 2436506 24 32 36 11 2460138 12 16 18 12 2460246 12 16 18 13 31709H5C 24 32 18 14 35009C 60 80 90 15 00000200 60 80 90 19 37054H8C 34 42 48 20 32905C 44 52 18 22 2461279 12 26 30 23 2461085 22 26 30 24 00001800 34 42 48 25 00759635 34 42 48 26 37051H5C 44 52 60 27 330014C 4 6 8 28 2420218 2 - - 2430303-2 2 2430304 2-2 2430330-6 4 29 2438355 2 2 2 SPOOL-MACHINED SPOOL,MALE BEARING DISC,CONCAVE SOLID 24 X 6.5MM DISC,CONCAVE SOLID 24 X 8MM FEMALE BEARING SPOOL-MACHINED NUT LOCK TAB MALE END CAP BUMPER END CAP BEARING HANGER TRUNNION MOUNT ASY,TRUNNION HOUSING (SEE PAGES 19,20) WDMT,SPRING STOP MOUNT BRACKET HEX CAP 3/4-10 X 3 1/4 GR.5 LOCKWASHER 3/4 NUT 3/4 NC HEX PL CARRIAGE BOLT HEX LOCKNUT 1/2-13 ARM,DISC SCRAPER MOUNT BLADE,DISC SCRAPER LOCKNUT TLM 1/2 NC PLB FLATWASHER 1/2 HRDED NONPLTD CARB 1/2 NC 1 PL5 HEX NUT 1 1/2-6 AXLE,DISK - 1-1/2 X 95.4 (REAR) AXLE,DISK - 1-1/2 X 65.4 AXLE,DISK 1-1/2 X 80-1/2 (FRONT) AXLE,DISK - 1-1/2 X 50.4 20 X 6.5MM CONCAVE SOLID DISC 2438356 2 2 2 22 X 6.5MM CONCAVE SOLID DISC 30 2460730 2-2 ANGLE,5-BLADE SCRAPER MOUNT 2460731 2 - - ANGLE,6-BLADE SCRAPER MOUNT 2460732-6 4 ANGLE,3-BLADE SCRAPER MOUNT 2460733-2 2 ANGLE,4-BLADE SCRAPER MOUNT 32 31709H8C 36 48 30 HEX CAP 3/4-10 X 3 1/4 GR.8 33 2461087 12 16 18 PLATE,GANG MOUNT 34 2471070 24 32 36 WASHER, EM BEARING 35 37054H8L 22 26 30 CARB, 1/2" NC X 1-3/4"PL5 2008 Alamo Group Inc. Parts Section 17
FRONT MAINFRAME ITEM PART NO. QTY. DESCRIPTION 1 00011400 7 BOLT, 1/4" NC X 3/4" PL5 2 00015800 8 LOCKNUT, 3/8" NC 3 00016400 8 BOLT, 5/8" NC X 8" PL5 5 00035900 4 HEX BOLT, 5/16" NC X 3/4" PL5 6 00037200 24 LOCKNUT, 3/4" NC 7 00695100 16 LOCKNUT, 5/8" NC 8 00776031 1 CANISTER PARTS MANUAL 9 02918600 24 HEX BOLT, 3/4" NC X 2" PL8 10 02959924 3 LOCKNUT, 1/4" NC 11 02972565 4 BOLT, 3/8" NC X 4-1/2" PL5 12 2460239 1 WELDMENT, REAR MAINFRAME 13 2460248 1 WELDMENT, FRONT MAINFRAME 14 2460253 1 WELDMENT, LIFT CROSSTUBE FRONT 15 2460285 1 WELDMENT, LIFT CROSSTUBE REAR 16 2461616 1 COVER, VALVE MOUNT 17 2461618 1 PLATE, DISC DEPTH 18 2461880 1 PLATE, DISC DEPTH POINTER 19 2465504 16 CASTING, PIVOT BEARING HOUSING 20 2466775 8 BEARING PIVOT 21 2467350 1 VALVE, SEQUENCE 22 2468304 1 DECAL, DISC DEPTH GAUGE 23 316023H8C 8 BOLT, 5/8" NC X 8" PL8 2008 Alamo Group Inc. Parts Section 18
TRUNNION ASSEMBLY 1 ITEM PART NO. QTY. DESCRIPTION 2460138 - ASY,TRUNNION HOUSING 1 2435520 1 HOUSING,TRUNNION BEARING 2 2436800 2 SEAL,2.625 ID X 3.818 OD X.41 3 2438201 4 RETAINING RING, 3.750 4 2436004 1 DBL TAPERED BEARING,1 1/2 SQ B 5 00764386 1 GREASE FITTING,8MMX1 STRAIGHT 6 00749201 2 BEARING CUP 382A NOTE: Two styles of Trunnion Housings have been used. See page 20 for more information. 2008 Alamo Group Inc. Parts Section 19
TRUNNION ASSEMBLY 2 ITEM PART NO. QTY. DESCRIPTION 2460138 - ASY,TRUNNION HOUSING 1 2436800 2 SEAL,2.625 ID X 3.818 OD X.41 2 2438201 2 RETAINING RING, 3.750 3 2436004 1 DBL TAPERED BEARING,1 1/2 SQ B 4 00764386 1 GREASE FITTING,8MMX1 STRAIGHT 5 2435520A 1 HOUSING,TRUNNION BEARING 6 2461731 2 PLATE,TRUNNION SEAL RETAINER 7 00749739 6 SELF TAP 1/4 NC 1/2 8 00749201 2 BEARING CUP 382A NOTE: Two styles of Trunnion Housings have been used. See page 19 for more information. 2008 Alamo Group Inc. Parts Section 20
HUB & SPINDLE ITEM PART NO. QTY. DESCRIPTION 2460102 - ASY,HUB & SPINDLE 1 2465512 1 HUB, MACHINED CASTING 2 0536004 1 BEARING, CUP 3 2466002 1 CUP, INNER BEARING 4 2468404 8 STUD, 5/8 NF X 2-1/2 WHEEL 5 2462539 1 SPINDLE, 2-1/2 X 16-3/8 6 2466700 1 CAP, HUB 7 0536005 1 BEARING CONE 8 2466003 1 BEARING CONE 9 330910C 1 NUT, HEX SLOTTED 1-14 10 2468405 1 COTTER PIN,.200 X 2-1/4 11 2466802 1 SEAL, GREASE 12 6W300 8 NUT, WHEEL 5/8-18 PL 13 2468604 1 SPINDLE WASHER 1" 2008 Alamo Group Inc. Parts Section 21
LIGHT KIT PARTS 2008 Alamo Group Inc. Parts Section 22
LIGHT KIT PARTS ITEM PART # QTY. DESCRIPTION 1 2460239 1 WELDMENT, REAR MAINFRAME 2 2461604 4 BRACKET, UPRIGHT LIGHT 3 2461415 2 STRAP, LIGHT MOUNT 4 2460260 2 WDMT, MID MOUNT BRACKET 5 2461623 4 PLATE, LIGHT BRACKET 6 00015800 37 NUT, TOPLOCK 3/8 NC 7 32901C 18 HEX LOCKNUT 1/4-20 8 00726957 2 LIGHT, SINGLE AG-AMB/AMB 9 00726956 2 LIGHT, SINGLE AG-RED/BLACK 10 00021400 29 HEXB, 1/4 NC X 3/4 PL5 11 00011400 26 HHCS 3/8 NC X 1 PL5 12 1458398 4 DECAL, ORANGE REFLECTOR 13 1458392 4 DECAL, RED REFLECTOR 14 00037200 88 NUT, 3/4-10 CENTERLOCK 15 317024H5C 4 HEXB, 3/4 NC X 10 PL5 16 00726961 2 HARNESS, EXTENSION 10' 17 2438621 1 SPADE BRACKET, SMV MOUNTING 18 03200347 1 EMBLEM, SMV 19 1458393 6 DECAL, YELLOW REFLECTOR 20 2438607 1 SOCKET, MOUNTING 21 329023C 4 HEX LOCKNUT #10-24 22 00726963 1 HARNESS, WISHBONE - 10' 23 00753642 6 HHCS 3/8 NC X 1-1/4 PL5 24 3263N6C 4 PAN HEAD SCREW 10-24 X 1/2 25 00726964 1 MAIN HARNESS - (NOT SHOWN) 2008 Alamo Group Inc. Parts Section 23
HOSE SCHEMATIC 2008 Alamo Group Inc. Parts Section 24
HOSE SCHEMATIC ITEM PART NO. QTY. DESCRIPTION 1 2467202 1 HOSE 400" - YELLOW BAND 2 02042400 4 HYDRAULIC ADAPTER, STRAIGHT 3 2467201 2 HOSE 110" - RED BAND 4 2467200 2 HOSE 90" - BLUE BAND 5 2467204 2 HOSE 270" - ORANGE BAND 6 2467203 2 HOSE 412" - GREEN BAND 7 02962213 11 HYDRAULIC ADAPTER 8 00696800 5 HYDRAULIC ADAPTER, STRAIGHT 9 2467350 1 VALVE, SEQUENCE 10 2467353 1 VALVE, CUSHION 2008 Alamo Group Inc. Parts Section 24
HOSE SCHEMATIC FOLDING WING 2008 Alamo Group Inc. Parts Section 25
HOSE SCHEMATIC FOLDING WING ITEM PART NO. QTY. DESCRIPTION 1 61027400 2 STRAIGHT ADAPTOR 8MP-6MJ 2 2467207 2 HOSE #4-6FJX - 6FJX - 190LG (GREEN BAND) 3 2467106 2 ADAPTER,HYD CROSS 4 2467217 4 HOSE #4-6FJX - 6FJX - 144LG (ORANGE BAND) 5 1937156 8 SPEC. 90DG ELBOW W/RESTRICTOR 6 2467215 2 HOSE #4-6FJX - 6FJX - 130LG (RED BAND) 7 2467216 4 HOSE #4-6FJX - 6FJX - 108LG (BLUE BAND) 8 00726792 2 ADP HYD TEE 6MJ - 6MJ - 6MJ 2008 Alamo Group Inc. Parts Section 25
DISC LIFT CYLINDER ITEM PART NO. QTY. DESCRIPTION 1 2417158 1 CLEVIS CAP 2 2417157 1 ROD CAP 3 2417160 1 PISTON 4 2417159 1 ROD 5 2417155 1 TUBE 6 2417156 4 TIE ROD 7 3047104 2 CLEVIS PIN 8 492110 4 CLEVIS PIN CLIP 10 * 2 END CAP O-RING 11 * 1 ROD WIPER SEAL 13 * 1 ROD DUST SEAL 14 * 1 PISTON SEAL 15 * 2 PISTON WEAR RING 16 3047117 1 NYLON THREAD PROTECTOR 17 1917140 1 ROD CLEVIS 18 0116000 1 SET SCREW 20 33005H5C 8 TIE ROD NUT 25 5JRC16140 1 PISTON NUT 27 1917132 1 PORT PLUG 40 * 2 END CAP BACKUP WASHERS * 2417161 1 KIT,SEAL 2008 Alamo Group Inc. Parts Section 26
TONGUE CYLINDER ITEM PART NO. QTY. DESCRIPTION 1 2417158 1 CLEVIS CAP 2 2417157 1 ROD CAP 3 2417160 1 PISTON 4 00774737 1 ROD 5 00774748 1 TUBE 6 00774742 4 TIE ROD 7 3047104 2 CLEVIS PIN 8 492110 4 CLEVIS PIN CLIP 10 * 2 END CAP O-RING 11 * 1 ROD WIPER SEAL 13 * 1 ROD DUST SEAL 14 * 1 PISTON SEAL 15 * 2 PISTON WEAR RING 16 3047117 1 NYLON THREAD PROTECTOR 17 1917140 1 ROD CLEVIS 18 0116000 1 SET SCREW 20 33005H5C 8 TIE ROD NUT 25 5JRC16140 1 PISTON NUT 27 1917132 1 PORT PLUG 40 * 2 END CAP BACKUP WASHERS * 2417161 1 KIT,SEAL 2008 Alamo Group Inc. Parts Section 27
MAIN AXLE LIFT CYLINDER ITEM PART NO. QTY. DESCRIPTION 1 2417180 1 CLEVIS CAP 2 2417181 1 ROD CAP 3 1917149 1 PISTON 4 2417182 1 ROD 5 1917136 1 TUBE 6 1917138 4 TIE ROD 7 1917152 2 CLEVIS PIN 8 49045 4 CLEVIS PIN CLIP 10 * 2 END CAP O-RING 11 * 1 ROD WIPER SEAL 13 * 1 ROD DUST SEAL 14 * 1 PISTON SEAL 15 * 2 PISTON WEAR RING 16 3047117 1 NYLON THREAD PROTECTOR 17 2417183 1 ROD CLEVIS 18 00774740 1 SET SCREW 20 33017H5C 8 TIE ROD NUT 25 1917155 1 PISTON NUT 27 1917132 1 PORT PLUG 40 * 2 END CAP BACKUP WASHERS * 1917156 1 KIT,SEAL W/PSP SEALS 2008 Alamo Group Inc. Parts Section 28
DISC WING LIFT CYLINDER ITEM PART NO. QTY. DESCRIPTION 2467105 - CYLINDER,HYDRAULIC 3-1/2 X 10 1 00774728 1 CLEVIS CAP 3.50-3/4 ORB 1.00 2 2417184 1 CAP,CYLINDER ROD 3 00774733 1 PISTON 3.50-1.00-S-WR PSP &2WR 4 2417159 1 ROD,CYLINDER 1-1/4 5 2417185 1 TUBE,CYLINDER 6 2417186 4 ROD,CYLINDER TIE 7 3047104 2 PIN, 1 8 49045 4 COTTER PIN 3/16 X 1 3/4 16 3047117 1 THREAD LOCK 17 1917140 1 ROD CLEVIS 18 00774740 1 SC SCKT SET 3/8UNCX1/2 KNUR 20 33017H5C 8 NUT,HEX 5/8-18 UNF GR.5 PLT 25 2417187 1 NUT,CYLINDER PISTON 27 1917132 1 SCKT HD O-RNG PLUG,3/4-16 UNF, 10 * 2 END CAP O-RING 11 * 1 ROD WIPER SEAL 13 * 1 ROD DUST SEAL 14 * 1 PISTON SEAL 15 * 2 PISTON WEAR RING 40 * 2 END CAP BACKUP WASHERS * 2417161 1 KIT,SEAL 2008 Alamo Group Inc. Parts Section 29
SEQUENCE VALVE ITEM PART NO. QTY. DESCRIPTION 2467350 - VALVE,SEQUENCE 1 2417354 1 BLOCK, MANIFOLD SEQUENCE VALVE 2 02962213 4 ADAPTER, HYDRAULIC ELBOW 3 00696800 4 ADAPTER, HYDRAULIC STRAIGHT 4 2417353 2 VALVE, SEQUENCE - 2000 PSI 5 001582 3 PLUG 6 2417350 2 VALVE, CHECK 7 2417351 1 PLUG 8 2417352 1 PLUG 2008 Alamo Group Inc. Parts Section 30
RELIEF VALVE ITEM PART # QTY. DESCRIPTION 10 2467353 1 BLOCK, RELIEF VALVE 11 2467352 1 CARTRIDGE, RELIEF VALVE 12 00770346 2 ADAPTER, HYD. STGHT 13 02967150 1 ADAPTER, HYD. ELBOW 14 2467221 1 HOSE, #8 - #8FJX - #8FJX - 28" LG 15 2467222 1 HOSE, #8 - #8FJX - #8FJX - 35" LG 16 02761100 2 ADAPTER, HYD. ELBOW 17 2467107 1 ADAPTER, HYD. ELBOW 18 02766000 2 HEXB 1/4" NC 1-3/4" PL5 19 32901C 2 HEX LOCKNUT 1/4"-20 2-WAY ZINC 20 2461616 1 COVER, VALVE MOUNT 2008 Alamo Group Inc. Parts Section 31
SUPER LINK ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 2450129 - ASY,TOP LINK-M36 X 3 1 2457504 1 TURNBUCKLE - RH 2 2457505 1 TURNBUCKLE - LH 3 2457506 1 BODY, TURNBUCKLE TUBE 4 2457507 1 COLLAR, TURNBUCKLE LOCKING 2008 Alamo Group Inc. Parts Section 32
PAGE LEFT BLANK INTENTIONALLY
COIL TINE LEVELER 1700 (OPTIONAL) S/N 10077 -CURRENT Rev 09-04 2008 Alamo Group Inc. Parts Section 33
COIL TINE LEVELER 1700 (OPTIONAL) S/N 10077 -CURRENT Rev 09-04 ITEM PART NO. QTY. DESCRIPTION 1 00037100 16 HEXB 3/4 NC 2-1/2 PL5 2 00725712 2 PIN PULL BENT 1/2 X 3 WITH 3 00748823 6 HHCS 1/2-13UNC 1-1/2 PL5 4 00773592 4 PIN, SAFETY LOCK LYNCH 5 00999418 78 HHCS 1/2-13UNC 3-1/2 PL5 6 1458393 2 DECAL,YELLOW REFLECTOR 7 2460288 4 WDMT,FRAME TUBE 8 2460289 4 WDMT,MOUNT 9 2460290 2 WDMT,MOUNT EXTENSION 10 2460294 6 WDMT,ANGLE ARM 11 2460295 2 WDMT,ADJUSTMENT BAR 12 2460304 4 WDMT,PIVOT PIN 13 2460332 2 WDMT,INNER CROSS TUBE 14 2461080 8 PLATE,SHANK MOUNT 15 2464878 4 BUSHING 16 2464879 60 BUSHING,TINE 17 2464883 6 TUBE,5-COIL TINE BAR 18 2467421 4 SRRING,EXTENSION 19 2467422 30 TINE,DBL SPRING HARROW COIL 20 2468402 4 BOLT,EYE 21 2468403 8 U-BOLT 22 02675800 8 HHCS 5/8-11UNC 1-1/2 PL5 23 02957007 4 HHCS 5/8 NC 5 PL8 24 317026H5C 12 HEX CAP 3/4-10 X 11 GR.5 25 317028H5C 4 HEX CAP 3/4-10 X 12 GR.5 26 35009C 32 LOCKWASHER 3/4 28 2460292 4 WDMT,SHORT MOUNT TUBE 32 00001800 84 LOCKNUT TLM 1/2 NC PLB 33 00010400 8 NUT 5/8 NC HEX PL 34 00695100 28 NUT,TOPLOCK 5/8 NC PLB 35 00000200 32 NUT 3/4 NC HEX PL 2008 Alamo Group Inc. Parts Section 34
COIL TINE LEVELER 2500 2200 2200F S/N -CURRENT (OPTIONAL) 2008 Alamo Group Inc. Parts Section 35
COIL TINE LEVELER 2500 2200 2200F S/N -CURRENT (OPTIONAL) ITEM PART NO. QTY. QTY DESCRIPTION 2200 2500 & 2200F 1 2460290 2 2 WDMT,MOUNT EXTENSION 2 2460291 4 - WDMT,MOUNT TUBE 2460331-4 WDMT,CTL MOUNT TUBE 3 2460289 4 4 WDMT,MOUNT 4 2460332 2 2 WDMT,INNER CROSS TUBE 5 2460333 2 2 WDMT,OUTER WING TUBE 6 2464886 6 - TUBE,2-COIL TINE BAR 2464880-6 TUBE,3-COIL TINE BAR 7 2460294 12 12 WDMT,ANGLE ARM 8 00999418 108 120 HHCS 1/2-13UNC 3-1/2 PL5 9 00001800 120 132 LOCKNUT TLM 1/2 NC PLB 10 2467422 36 48 TINE,DBL SPRING HARROW COIL 11 2464879 72 84 BUSHING,TINE 12 2464887 6 6 TUBE,4-COIL TINE BAR 13 2460288 8 8 WDMT,FRAME TUBE 14 2468402 4 4 BOLT,EYE 15 2467421 4 4 SRRING,EXTENSION 16 00773592 4 4 PIN, SAFETY LOCK LYNCH 17 2460304 4 4 WDMT,PIVOT PIN 18 2468403 8 8 U-BOLT 19 2467103 2 2 CYLINDER,HYDRAULIC 2-1/2 X 8 20 00725712 4 4 PIN PULL BENT 1/2 X 3 WITH 21 2464878 4 4 BUSHING 23 2460312 2 2 WDMT,CYLINDER PIN 24 1937156 4 4 SPEC. 90DG ELBOW W/RESTRICTOR 25 2461080 8 8 PLATE,SHANK MOUNT 26 1458393 2 2 DECAL,YELLOW REFLECTOR 28 2460334 2 2 WDMT,TRANSPORT LOCK PIN 29 2460295 4 4 WDMT,ADJUSTMENT BAR 30 00010400 8 8 NUT 5/8 NC HEX PL 31 02675800 16 16 HHCS 5/8-11UNC 1-1/2 PL5 32 00695100 36 36 NUT,TOPLOCK 5/8 NC PLB 33 02957007 4 4 HHCS 5/8 NC 5 PL8 34 00000200 32 32 NUT 3/4 NC HEX PL 35 35009C 32 32 LOCKWASHER 3/4 36 00037100 16 16 HEXB 3/4 NC 2-1/2 PL5 37 317028H5C 4 4 HEX CAP 3/4-10 X 12 GR.5 38 317026H5C 12 12 HEX CAP 3/4-10 X 11 GR.5 39 00015800 2 2 NUT,TOPLOCK 3/8NC PLB 40 00753642 2 2 HHCS,3/8NC X 1-1/4,ZP,GRD5 41 00748823 12 12 HHCS 1/2-13UNC 1-1/2 PL5 42 2467206 2 2 HOSE RED 400"(NOT SHOWN) 43 2467207 2 2 HOSE RED 190"((NOT SHOWN) 44 2467208 2 2 HOSE RED 206"( (NOT SHOWN) 2008 Alamo Group Inc. Parts Section 36
COIL TINE LEVELER WING CYLINDER (OPTIONAL) ITEM PART NO. QTY. DESCRIPTION 2467103 - CYLINDER,HYDRAULIC 2-1/2 X 8 1 00774729 1 CLEVIS CAP 2 00774734 1 ROD CAP 3 2417178 1 PISTON 4 00774753 1 ROD 5 3047111 1 TUBE 6 3047112 4 TIE ROD 7 3047104 2 CLEVIS PIN 8 49045 4 CLEVIS PIN CLIP 10 * 2 END CAP O-RING 11 * 1 ROD WIPER SEAL 13 * 1 ROD DUST SEAL 14 * 1 PISTON SEAL 15 * 2 PISTON WEAR RING 16 3047117 1 NYLON THREAD PROTECTOR 17 1917140 1 ROD CLEVIS 18 00774740 1 SET SCREW 20 33003H5C 8 TIE ROD NUT 25 5JRC12160 1 PISTON NUT 27 1917132 1 PORT PLUG 40 * 2 END CAP BACKUP WASHERS * 2417179 1 KIT,SEAL 1.125-1.25 PSP 2008 Alamo Group Inc. Parts Section 37
PAGE LEFT BLANK INTENTIONALLY Parts Section 1
COIL TINE HOSE SCHEMATIC (OPTIONAL) 2008 Alamo Group Inc. Parts Section 38
COIL TINE HOSE SCHEMATIC (OPTIONAL) ITEM PART NO. QTY. DESCRIPTION 1 61027400 2 STRAIGHT ADAPTOR 8MP-6MJ 2 2467208 2 HOSE #4-6FJX - 6FJX - 206LG 3 2467207 2 HOSE #4-6FJX - 6FJX - 190LG 4 1937156 4 FITTING, 90 ELBOW W/RESTRICTOR 5 00726792 2 ADP HYD TEE 6MJ - 6MJ - 6MJ 6 2467206 2 HOSE #4-6FJX - 6FJX - 400LG 2008 Alamo Group Inc. Parts Section 38
LIMITED WARRANTY 1. LIMITED WARRANTIES 1.01.M&W warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser ( Purchaser ) and warrants for six months to the original commercial or industrial purchaser ( Purchaser ) that the goods purchased are free from defects in material or workmanship. 1.02.Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship. 1.03.This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found in your Operator s Manual. 1.04.Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of Manufacturer. 2. REMEDIES AND PROCEDURES. 2.01.This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer within 30 days of purchase. 2.02.Purchaser claims must be made in writing to the Authorized Dealer ( Dealer ) from whom Purchaser purchased the goods or an approved Authorized Dealer ( Dealer ) within 30 days after Purchaser learns of the facts on which the claim is based. 2.03.Purchaser is responsible for returning the goods in question to the Dealer. 2.04.If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, Manufacturer will: (a) (b) Repair or replace the defective goods or part(s) or Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by Manufacturer. The choice of remedy shall belong to Manufacturer. 2.05.Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the Dealer to the designated factory. 3. LIMITATION OF LIABILITY. 3.01.MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 3.02.MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE GOODS. 3.03.EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER S LIABILITY HEREUNDER FOR DAMAGES INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS. 3.04.NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED. 4. MISCELLANEOUS. 4.01.Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County, Texas. 4.02.Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term. 4.03.If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein. 4.04.Applicable law may provide rights and benefits to purchaser in addition to those provided herein. KEEP FOR YOUR RECORDS M&W ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification when applying for warranty. M&W Implement Model Serial Number Date Purchased Dealer ATTENTION: READ YOUR OPERATOR'S MANUAL M&W An Alamo Group Company 1020 South Sangamon Ave. Gibson City, Illinois 60936 217-784-4261
TO THE OWNER/OPERATOR/DEALER To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety requirements of tractor operators: REQUIRED OF THE OWNER: 1. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and 2. Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and 3. Ensure that each employee uses such Seatbelt while the tractor is moving; and 4. Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected area provided by the ROPS. REQUIRED OF THE OPERATOR 1. Securely fasten seatbelt if the tractor has a ROPS. 2. Where possible, avoid operating the tractor near ditches, embankments, and holes. 3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces. 4. Stay off slopes too steep for safe operation. 5. Watch where you are going - especially at row ends, on roads, and around trees. 6. Do not permit others to ride. 7. Operate the tractor smoothly - no jerky turns, starts, or stops. 8. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer. 9. When the tractor is stopped, set brakes securely and use park lock, if available. Keep children away from danger all day, every day... Equip tractors with rollover protection (ROPS) and keep all machinery guards in place... Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens.
EM 1700 2200 2200F & 2500 PL 08-13 Printed U.S.A. P/N 5004WP