Series PZ and PZi Pulse Metering Pumps

BULLETIN PZ-3 Series PZ and PZi Pulse Metering Pumps CHEMICAL PUMP CO., INC. US Patent #6,283,717 The Age of Intelligent Pumps Finally Arrives!

TYPE PZ (manual) TYPE PZi4 (automatic) TYPE PZi8 Intelligent Pump (programmable) PZ & PZi Features ( SIZES 31/61/12) TYPE PZ PZi4 PZi8 Manual control PZ Models (Speed only is adjustable from 15 to 3 SPM) PZi Models (Speed 1 to 3 SPM plus stroke length 5% to 1%) Control input 1 External interlock (Examples: level switch, remote start, reset) Operation display Indicates speed and status Indicates speed, feed rate*, status and other operational data Signal input Pulse signal (Frequency-division 1/1 to 1/9999, Multiplication 1 to 9999) 4-pin connector Analog signal (Shift function, Proportional band function) Alarm output (Level switch, injection monitor*) Signal output 2 Operation pulse signal (Synchronous pulse output for each stroke) 8-pin connector Operation progress signal (Time or number of strokes remaining in program) Alarms Alarm display, output and action (run, pause or stop) can be selected Power supply for flow checker Other functions Interval operation (Repeat cycle program, see below) Counter (Countdown batch injection, see below) NOTES: 1. Two separate configurable inputs. 2. Two separate configurable outputs, either open collector (alarm, error, run) or pulse (operational sync or end of cycle). *When used with flow checker shown on page 4. ANALOG SIGNAL INPUT PZi4 and PZi8 PULSE SIGNAL INPUT PZi4 and PZi8 DC4() to 2mA input 1. Proportional band function The proportional band can be adjusted within a range of ±1% to ±999%. Pump response to increasing input signal is easily reversed from min. 4mA and max. flow at 2mA to max. flow 2mA and min. flow at 4mA. ma to 2mA range on PZi8 models. Pump stroke (spm) 3 1% 15 5% 1% 2% 5% 1% 999% 1% 3 4() 4.16 12 2 4() 4.16 12 2 Analog input (ma) Analog input (ma) 2. Shift function Shift can be set within the range ±1% allowing a min. preset flow at (4mA) signal or allowing no flow until the input signal exceeds a preset value. Pump stroke (spm) 3 27 1% Pump operation 15 (A) 2% (B) 999% 1. Frequency-division (1/1 to 1/9999 adjustable) Example: 1/6 frequency-division Signal Pump operation 2. Multiplication (1 to 9999 adjustable) Example: 5 times multiplication (A) Pulses 5 times next 5 strokes at normal operating speed. Signal Conventional products (A) (B) Pulses 5 times evenly spaced over one minute. PZi (B) Injection is more uniform. 2 PULSE SIGNAL INPUT 4() Signal 2mA PZi8 ONLY 1. Counter (Metering batch injection) Pump pulses up to max. 9999x1 times by a start (switch) signal. Multiplication settings: x1, x1, x1 and x1. Display counts down. 2. Interval function repeat cycle ON time and OFF interval can be easily set from 1 to 9999 minutes respectively. ON OFF 2min 8min External timer not required.

Variety of Liquid End Materials Standard Model: PVC (VFC/VEC) General chemical applications Valve seats and O-rings are available in Viton or EPDM Chlorine Model: Acrylic (CL) Transparent pump head allows visual check of valves Reduced head volume and upward sloping ports vent gas away from diaphragm Improved pump efficiency for countering gas lock Universal Model: PVDF (FFC/FEC/FTC) For most chemicals and highly corrosive chemicals Valve seats and O-rings are available in Viton, EPDM or Teflon Stainless Steel Model (SS) For solvents and other chemicals where plastics are not suitable Chlorine Model: Acrylic (ARPZ) CL model with automatic air release mechanism Derate capacity 5% for air release models MATERIAL PUMP TUBE VALVE CHECK FOOT VALVE BACKPRESSURE SUCTION DISCHARGE CODE HEAD JOINT SEAT BALL DIAPHRAGM & STRAINER INJECTION ASSEMBLY CONNECTION TUBE* CONNECTION TUBE* VFC PVC PVC Viton Ceramic PTFE PVC PVC 3/8" Tube Soft PVC 2 3/8" Tube PE 2 VEC PVC PVC EPDM Ceramic PTFE PVC PVC 3/8" Tube Soft PVC 3/8" Tube PE CL Acrylic PVC Viton Ceramic PTFE PVC PVC 3/8" Tube Soft PVC 3/8" Tube PE ARPZ Acrylic PVC Viton Ceramic PTFE PVC PVC 3/8" Tube Soft PVC 3/8" Tube PE SS 316SS N/A EPDM 316SS PTFE Not Included Not Included 3/8" MNPT None 3/8" MNPT None FFC PVDF PP Viton Ceramic PTFE PVDF Molded PVDF Molded 3/8" Tube PE 1 3/8" Tube PE FEC PVDF PP 3 EPDM Ceramic PTFE PVDF Molded PVDF Molded 3/8" Tube PE 1 3/8" Tube PE 3 FTC PVDF PVDF Teflon Ceramic PTFE PVDF Molded PVDF Machined 3/8" Tube FEP 1,2 3/8" Tube FEP 2 1 Ceramic Weight Included 2 PZ-32 and PZ-52 Models 18 mm OD x 12 mm ID Tube 3 22 psi Model PZ/PZi-31-FEC *NOTE: 3/8" Tube is 3/8" OD x 1/4" ID Soft PVC for VFC Models; PTFE for FTC Models 1/4" Tube Joint and Tube PP To specify pump, choose the type from the chart on page 2 plus the size from the chart on page 6 (ex: PZi4-31). Then add the appropriate material code from the chart below (ex: PZi4-31-FFC). Complete instructions regarding Model Number Selection are on page 6. PZD/PZi-32/52 High Capacity Models The PZD pump is simple to set and operate as the injection rate can be entered directly. This eliminates conversions. Injection rate can be set three ways: Stroke speed: 1 to 3 spm Percentage: 1 to 1% Direct entry of injection rate in ml/min Set points can be easily viewed on the LCD High Capacity models are available in material codes VFC, SS and FTC only. VFC model is shown. Calibration function is standard. Calibration measures the actual discharge volume under the exact operating conditions and stores that value to ensure the correct injection rate. 3

Feed Verification DIMENSIONS 3-3/8'' (85) 2-3/8'' (6) inches (mm) 1-1/2'' (39) 2-5/8'' (66) Model FC-1 FLOW CHECKER (shown with PZi pump) The Model FC-1 Flow Checker output provides vital information for water treatment programs requiring feed verification to manage chemistry and monitor drum inventory. 2'' (5) LED: RED LED: GREEN 2'' (48) 6'' (149) The flow checker mounts directly to the discharge of PZ and PZi metering pumps. The flow checker is an oval gear flow meter which measures the pump output and transmits one pulse for each 1 ml of flow. MODEL FLC1-B FLOW INDICATOR TOTALIZER see page 5 Flow checker output can be connected to Model PZi8 Pumps for instantaneous indication of pump output displayed on the pump LCD. The flow checker output can also be connected to a Neptune Model FLC1-B Flow Indicator Totalizer, to display both instantaneous flow and totalized flow. FLOW CHECKER SELECTION CHART Connect the flow checker output to your controller or PLC. MODEL NUMBER MATERIAL USE w/ PUMP MODEL 4 FC-1P-P-N1 Ryton* PZ or PZi-31 FC-1N-P-N1 Noryl** PZ or PZi-31 FC-1P-P-N2 Ryton* PZ or PZi-61 or -12 FC-1N-P-N2 Noryl** PZ or PZi-61 or -12 LIQUID-END MATERIALS PART MODEL MODEL NAME FC-1P- FC-1N- Body Ryton* Noryl** Ball Check Ceramic Ceramic Ball Guide/Joint PVC PVC Valve Seat/O-Ring EPDM Fluororubber * Ryton: PPS Polyphenylene-sulfide (for general chemicals) ** Noryl: PPO Polyphenylene-oxide (for sodium hypochlorite) SPECIFICATIONS Pulse constant 1mL /pulse Accuracy ±3% (Depends on nature of chemical, flow rate, temperature and back pressure.) Normal operating pressure 14 psi (1 Kg/cm 2 ) Momentary maximum 2 psi (14 Kg/cm 2 ) operating pressure Temperature Liquid viscosity Output Power requirement 32 14 F ( 4 C) (Liquid should not freeze.) 1 to 5 cps Open collector (Collector capacity: 3V, 3mA) 4.5 to 25VDC (2mA Max.) Green LED lights for each pulse output. Red LED on when the power is ON. NOTES: 1. Do not use the flow checker if tiny particles may be contained in the pumped liquid. 2. Pressure loss is.5 Kg/cm 2 (at maximum flow rate using water).

MODEL PZiA Automatic Flow Control Electronic Metering Pump Features Built-in calibration Maintains precise feed rate by correcting for changes in pressure/viscosity Precise batch injection Benefits PZiA Electronic Metering Pumps are the first in the world to feature an integrated automatic discharge volume control. Special circuitry allows onboard calibration of pump flow under actual process conditions. Each PZiA is furnished with a Flow Checker for feed verification and a constant pressure valve for the best possible accuracy. Once calibrated, the pump can be manually set or can be controlled by an analog signal. The pump then automatically adjusts by increasing or decreasing the stroking speed to maintain the precise flow rate regardless of changes in temperature, pressure, or viscosity. PZiA pump accuracy has been verified by KEMA. Constant Pressure Valve Flow Checker Stroke Adjustment Dial LCD Display (w/ backlight) 8-pin Signal Connector 4-pin Signal Connector (for flow checker) PZiA also performs precise batch injection. After calibration, a specific amount to be injected is entered on the electronic touch pad. Pump may be started manually or initiated by remote signal. The pump runs as long as necessary for the oval gear meter to measure the set amount and resets for the next command. Flow Indicator Totalizer 1/16 DIN Case Pulse Input: NPN open collector or voltage pulse Integral 12 VDC sensor power supply Analog Output: 4 2 madc User Scalable Indication Displays for Flow Rate and Totalized Flow: Flow Rate: 4-digit, 8mm LED, decimal point selection Totalized Flow: 5 digit, 8mm LED, decimal point selection MODEL FLC1-B Flow rate is averaged over 9 to 9 second user adjustable time period Two Alarm Outputs and Displays: Can be assigned to totalized flow for Batch Control Remote or Local Reset Remote Inhibit Terminals Power Requirements: 94 to 264 VAC, 5 to 6 Hertz, 5 VA Power Interruption: 3 day memory retention 5

Advantages Digital settings from 15 to 3 pulses per minute on PZ models and from 1 to 3 pulses per minute on PZi and PZD models High stroking speed ensures more uniform distribution of chemical at low feed rates Pump delivery is constant at any voltage from 94 to 264 VAC single phase and is not affected by voltage fluctuations Outdoor use pump is water and UV resistant. Equivalent to IEC specification IP65. Dust proof, wash down duty (with proper electrical connection). Applications PUMP HEAD CROSS SECTIONAL VIEW 1 2 3 4 5 6 7 8 Hose nut Retaining ring Hose joint Ball guide Ball check Valve seat Air release valve Diaphragm Injection of chemicals to boilers and cooling towers Chlorine sterilization for food plants, small-scale water-supply systems, buildings and swimming pools Injection of nutrients and disinfectants in the livestock industry, such as poultry and hog producers, as well as for hydroponic cultivation Very low flow rate injection of low viscosity liquids for any application (1 CPS max.) 9 O-ring MODEL NUMBER SELECTION The complete model number consists of three parts: TYPE + SIZE + MATERIAL CODE TYPE specify PZ for manual control; specify PZi4 for external input; specify PZi8 for programmable models. See chart on page 2. SIZE size code selects the capacities per the chart below. Sizes -31, -61 and -12 are available for type PZ, PZi4 or PZi8. Note higher capacity sizes -32/52 have slightly different type codes. Specify type PZD for manual control; specify type PZi for external input. MATERIAL CODE select from chart on page 3. Example The complete model for a pump with a Kynar liquid end with Viton seals rated at 3 ml/min capable of accepting a 4-2mA input would be: Type PZi4 + Size -31 + Material code -FFC The complete model number becomes PZi4-31-FFC SPECIFICATIONS AND PERFORMANCE TABLE For higher capacities, see Bulletin DP-5E. Type PZ, PZi4 or PZi8 Type PZD or PZi SPECIFICATION SIZE -31Hi.Pres. -31-61 -12-32 -52 Maximum discharge volume GPH (ml/min).44 (28).48 (3).95 (6) 1.6 (1) 5.7 (36) 8.5 (54) Maximum discharge pressure (Kg/cm 2 ) 22 psi (16) 14 psi (1) 115 psi (8) 6 psi (4) 45 psi (3) 3 psi (2) Stroke length (mm) 1. 1. 1. 1. 1.5 1.5 Connection 1/4" OD TUBE 3/8" OD x 1/4" ID TUBE 18 mm OD x 12 mm ID HOSE Power requirement Any single phase supply 5/6 Hertz from 94 to 264 VAC Maximum power consumption (VA) 2 2 25 25 5 5 Average power consumption (W) 15 15 18 18 3 3 NOTES: 1. High Pressure models are available as PZ-31, PZi4-31 or PZi8-31 only; available in FEC, FFC or SS only. Refer to Material Code Chart on page 3. 2. PZi4 models include 2-meter cable with 4-pin connector on one end; PZi8 models include separate 2-meter signal cables, one each with 4-pin and 8-pin connector end. PERFORMANCE CURVES Type PZ, PZi4 or PZi8 Conditions: Clean water, Room temperature Type PZD or PZi 45 SIZE -31 8 SIZE -61 12 SIZE -12 4 SIZE -32 6 SIZE -52 6 4 35 3 25 2 15 1 5 5 1 15 2 25 3.2MPa (2kgf/cm 2 ) 1.MPa (1kgf/cm 2 ) 7 6 5 4 3 2 1 5 1 15 2 25 3.2MPa (2kgf/cm 2 ).8MPa (8kgf/cm 2 ) 1 8 6 4 2 5 1 15 2 25 3.2MPa (2kgf/cm 2 ).4MPa (4kgf/cm 2 ) 35 3 25 2 15 1 5 5 1 15 2 25 3.1MPa (1kgf/cm 2 ).3MPa (3kgf/cm 2 ) 5 4 3 2 1 5 1 15 2 25 3.1MPa (1kgf/cm 2 ).2MPa (2kgf/cm 2 )

MATERIAL SELECTION CHART PUMPING LIQUID CONCENTRATION RECOMMENDED (in alphabetical order) TYPE Acetic acid 8% VFC/FFC Acetic acid concentrated 24 C FTC Aluminum sulfate VEC Amine VEC/FEC/SS Aqueous ammonia VEC Calcium/Sodium hypochlorite 12% CL/AR Caustic soda VEC Ferric/Ferrous chloride VFC Ferric/Ferrous sulfate VFC Hydrochloric acid 1% to conc. VFC Hydrogen peroxide 3% VFC Nitric acid 1% VFC Nitric acid 3% to conc. FTC Phosphoric acid 1% to conc. FTC Poly-aluminum chloride (PAC) VEC Potassium permanganate VEC Sulfuric acid to 4% VFC/FFC Sulfuric acid concentrated FTC INCLUDED WITH EACH PUMP: EXTERNAL DIMENSIONS Dimensions are shown in inches (mm). A 2-5/16 [59] 4-5/8 [118] 3-7/16 [87] B B 1/4 [6] *The mounting slots allow mounting from 3-7/16" (87) to 4-5/16" (11) centers. MODELS PZ/PZi-31/61/12 2-3/4 [7] 4-5/16 [11] MATERIAL A B C D E VFC/VEC 3 1 4 (83) 8 1 8 (26) 3 (76) 3 (76) 1 1 4 (31) FFC/FEC/FTC 3 5 8 (93) 9 (228) 3 7 8 (98) 3 7 8 (98) 1 2 (13) CL 3 1 4 (83) 8 (22) 2 7 8 (72) 2 7 8 (76) 1 1 4 (31) ARPZ 3 1 4 (83) 8 (22) 2 5 8 (66) 2 7 8 (76) 2 1 4 (56) SS 2 7 8 (73) 7 5 8 (194) 2 1 2 (64) 2 1 2 (64) 7 8 (22) C D E Foot Valve Strainer 4 [12] Back Pressure/Check Valve Injector with Quill Suction, Discharge and Air Release Tubing Power Cord with 3-Prong Plug Foot Valve Strainer Back Pressure Injector A B C D Signal Cable with Multi-Pin Connectors (PZi4 and PZi8 models) 6 [155] 2-5/8 [68] 5-7/8 [15] E F 4-5/8 [ø118] 7 [18] CAUTION Ambient temperature: 32 to 14 F ( to 4 C) Pumped liquids: Temperature: 32 to 14 F ( to 4 C), Viscosity: 1 CPS or less R3 1/4 [6] 3-7/16 [87] *The mounting slots allow mounting from 3-7/16" (87) to 4-5/16" (11) centers. This pump is designed for outdoor use. Avoid installing pump in a location where service life could be shortened (i.e., where it is exposed to direct sunlight or rain). This pump cannot pump liquids containing a slurry. If there is a shutoff valve in the discharge piping, a relief valve should be installed on the discharge side, close to the pump. 3-7/16 [87] MODELS PZD/PZi-32/52 MATERIAL A B C D E F VFC 9 5 8 (244) 7 (176) 3 1 2 (88) 3 1 2 (88) 1 (25) 3 3 8 (86) FTC 1 1 8 (256) 7 1 4 (183) 4 (11) 2 7 8 (72) 7 8 (22) 3 1 4 (83) SS 9 (227) 5 5 8 (144) 3 1 4 (83) 2 7 8 (72) 1 (24) 3 1 2 (89) 7

Quality Accessories by Neptune CORPORATION STOPS Use: Injection of chemicals pumped by proportioning pumps into tanks, mains, cooling towers and process systems. Request Bulletin CS B (MAX.) MATERIAL SIZE DIMENSIONS MODEL OF CONST. (D) A B C CS-75-PVC CPVC 3 4" NPT 4 3 4" 8 1 2" 1 2" NPT CS-1-PVC CPVC 1" NPT 5 9 16" 7 5 8" 1 2" NPT Kynar, 316 SS and C-2 also available. D MODEL CS-75-PVC WRENCH HOLD 3/8" WIDE x 1-1/4" LONG A 2-3/8" C 5/16" POLYETHYLENE SOLUTION TANKS & AGITATORS For PZ Series Pumps (Top Mounted) Self Supporting For Corrosive or Non-Corrosive Solutions Molded cover will accept PZ Series Pumps and Neptune Economy Agitators 3 or 5 Gallon Sizes TANKS MODEL SIZE HEIGHT DIA. MAX. WEIGHT ST-3 3 Gal. 23" 22" 19 lbs. ST-5 5 Gal. 32 1 2" 22" 2 lbs. AGITATORS PVC suction protector pipe included MODEL DESCRIPTION WEIGHT AN-316-3 316SS shaft and propeller, fits 3-gallon 14 lbs. polyethylene tank; 19" long shaft AN-316-5 316SS shaft and propeller, fits 5-gallon 14 lbs. polyethylene tank; 29" long shaft AN-E-3 AN-E-5 Epoxy-coated shaft and impeller, fits 3- gallon polyethylene tank; 19" long shaft Epoxy-coated shaft and impeller, fits 5- gallon polyethylene tank; 29" long shaft EZE-GRAB DUAL PUMP PLATFORM 14 lbs. 14 lbs. MODEL ST-5 PORTABLE MINI-TANK FEEDERS Mini-tank system offers portability and economy. Compact 23 1 2" wide, 36" long, 29" high size fits through doorways, in elevators and allows installation in small areas. Tank removes from base for ease of transport and handling. Total weight: 4 lbs. plus pump Use with electronic or motor driven pumps 8" manway standard Request Bulletin FDP/CFS MODEL MT-3 DESCRIPTION 3 Gallon System includes polypropylene suction piping with isolation valve and Y strainer (pump not included) MT-3T 3 Gallon Molded Tank and Base Only OPTIONS AND ACCESSORIES MT-CC MT-CT MTA Calibration Column Containment Basin 1/2 HP Mixer MODEL MT-3 Pre-packaged assembly on polyethylene base allows mounting of one or two pumps handling one or two chemicals. SOLD BY: CHEMICAL PUMP CO., INC. P.O. Box 247 Lansdale, PA 19446-247 Tel: 215-699-87 Fax: 215-699-37 Toll-Free Tel: 1-888-3NEPTUNE (1-888-363-7886) Toll-Free Fax: 1-8-255-417 Web Site: http://www.neptune1.com E-mail: pump@neptune1.com 23 Neptune Chemical Pump Co., Inc. All Rights Reserved Bulletin PZ-3 P/N ZL17971 Printed in U.S.A.