Manual Simba TL300 / TL350 Great Plains Manufacturing, Inc. www.greatplainsmfg.com Read the operators manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! Illustrations may show optional equipment not supplied with standard unit. ORIGINAL INSTRUCTIONS Copyright 2014 Printed EN
Contents Mainframe Mainframe...6 Tines Tine Mount - Shear Bolted...8 Tine Mount - Sprung...10 Tines...12 Levelling Discs Levelling Beam...14 Levelling Discs...16 Rollers Roll Frame...18 DD Lite 550 Roller...20 Cage, HD, V & ML Rollers...22 Aqueel II Roller...24 Lights Lights - Rear...26 Lights - Front...28 Spacings Tine & Levelling Disc Spacings...30 Simba TL 2
Contents (Alphabetical Order) Aqueel II Roller...24 Cage, HD, V & ML Rollers...22 DD Lite 550 Roller...20 Levelling Beam...14 Levelling Discs...16 Lights - Front...28 Lights - Rear...26 Mainframe...6 Roll Frame...18 Tine & Levelling Disc Spacings...30 Tine Mount - Shear Bolted...8 Tine Mount - Sprung...10 Tines...12 3 Simba TL
Using This Manual This manual is divided into sections. The first section contains General Information, a Table of Contents and an Alphabetical Page Index. The remaining sections divide the machine into segments (i.e. Frames, Hydraulics, etc.) which illustrate and list all parts. The Great Plains parts in this manual are specially designed for this machine and should be replaced with Great Plains parts only. The information in this manual is current at printing. Some parts may change to assure top performance. Right-hand and left-hand as used in this manual are determined by facing the direction the machine will travel while in use. Manual Replacement Replacement manuals are available. Refer to your dealer for additional information. Manual Revisions When this manual is revised, the modification date is printed on the front cover and on the revised page(s). Touch-up Paint Repaint parts where paint is worn or scratched to prevent rust. Aerosol touchup paint is available. To order use Great Plains parts numbers below: GP Green 821-001C GP Black 821-002C Below is an example of two facing pages from a parts manual. Familiarize yourself with the contents of these pages. Illustration Title Parts Tine Mount - Shear Bolt Parts Tine Mount - Shear Bolt Item Part No. Part Description Comments 1 604-309D HHCS M12X1.75X85 GR10.9 SPTHD 2 606-038A SHEAR BOLT UNIT C/W C/PLATE COMPLETE UNIT AS SHOWN 3 606-041H TINE SHEAR CLAMP 4 606-078D PLATE 25MM 5 803-281C NUT HEX NYLOCK M12X1.75 PLT 6 803-282C NUT HEX M16X2.00 NYLON INSERT 7 803-393C NUT HEX NYLOCK M20X2.5 8 804-244C WASHER FLAT M20 PLT 9 804-247C WASHER FLAT M16 PLT 10 827-143C BUSH SPRUNG -Ø16.5XØ13.5X26.15 Illustration 11 842-050C HHCS M20X2.5X160 GR8.8 12 842-051C HHCS M20X2.5X180 GR8.8 13 842-098C HHCS M16X2X90 GR8.8 SPTHD Parts List Illustration Number Machine 45007 Simba ST-Bar 606-037P 10 2013-08-21 2013-08-21 11 Simba ST-Bar 606-037P Manual Part Number Page number Modification Date Simba TL 4
Hardware Legend ADJ Adjuster HWHMS Hex Washer Head Machine Screw AR As Required HXBHCS Hex Socket Button Head Cap Screw BSP British Standard Pipe J Hex Jam Nut C Cap Screw JIC 37 Degree Tapered Thread CP Cotter Pin L Helical Spring Lock Washer CPHSSS Cup Point Hex Socket Set Screw LH Left Hand CPSHSS Cup Point Square Head Set Screw LUG Lug Bolt CPSQHSS Cup Point Square Head Set Screw NFC National Fine Cap Screw CRFCHMS Cross Recess Flat Countersunk Head Mach. Screw NPSM National Pipe Straight Mechanical CRPHMS Cross Recess Pan Head Machine Screw NPTF National Pipe Taper Fuel CRPHTFS Cross Recess Pan Head Thread Forming P Wide Plain Washer CRRHMS Cross Recess Round Head Machine Screw PHMS Pan Head Machine Screw CRTHMS Cross Recess Truss Head Machine Screw PLOW Plow Bolt CSNB Countersunk Square Neck Bolt QRC Quick Release Coupling FHMS Flat Head Machine Screw RH Right Hand FTC Full Thread Cap Screw RHMS Round Head Machine Screw H Hex Nut RHSNB Round Head Square Neck Bolt HCLN Hex Center Lock Nut SFCHMS Slotted Flat Countersunk Head Machine Screw HFLCS Hex Flange Lock Cap Screw SFHMS Slotted Fillister Head Machine Screw HFS Hex Flange Screw SP Special HFSLN Hex Flange Serrated Lock Nut SP SCREW Special Screw HFSS Hex Flange Serrated Screw SQHSS Square Head Set Screw HHCS Hex Head Cap Screw or Metric Bolt SRHMS Slotted Round Head Machine Screw HSBHCS Hex Socket Button Head Cap Screw SSS Socket Set Screw HSFCHCS Hex Socket Flat Countersunk Head Cap Screw STCS Self Tapping Cap Screw HSHCS Hex Socket Head Cap Screw STHMS Slotted Truss Head Machine Screw HSSS Hex Socket Head Screw WHEEL Wheel Studs and Hub Long Bolts HTLN Hex Top Lock Nut WING Wing Bolt HWHCS Hex Washer Head Cap Screw Replacement Hardware The Hardware Legend above lists hardware abbreviations used in the parts lists. The use of improper grades of hardware can result in personal injury, damage to equipment, or loss of property. 5 Simba TL
Mainframe 62001 Simba TL 6
Mainframe Item Part No. Part Description Comments 1 605-001H MAINFRAME - TL300 2 605-004H HEADSTOCK PLATE 3 605-005H HEADSTOCK BRACE RH 4 605-006H HEADSTOCK BRACE LH 5 605-010H PIN UPPER LINK CAT 3 6 605-011H PIN LOWER LINK CAT 3 7 605-016H MAINFRAME - TL350 8 803-416C NUT HEX M30X3.5 NYLON INSERT 9 804-160C WASHER FLAT M6 PLT 10 804-226C WASHER LOCK M6 PLT 11 804-257C WASHER FLAT M30 - OD60MM PLT 12 805-468C LYNCH PIN CAT 3 13 817-928C MANUAL HOLDER 14 827-137C BUSH SPRUNG - Ø40XØ31X20 15 842-043C HHCS M30X3.5X180 GR8.8 16 842-054C HHCS M6X1X12 GR8.8 17 842-080C HHCS M30X3.5X110 GR8.8 18 842-156C HHCS M30X3.5X100 GR8.8 SPTHD 7 Simba TL
Tine Mount - Shear Bolted 45007 Simba TL 8
Tine Mount - Shear Bolted Item Part No. Part Description Comments 1 604-309D HHCS M12X1.75X85 GR10.9 SPTHD 2 606-038A SHEAR BOLT UNIT C/W C/PLATE 3 606-041H TINE SHEAR CLAMP 4 606-078D PLATE 25MM 5 803-281C NUT HEX NYLOCK M12X1.75 PLT 6 803-282C NUT HEX M16X2.00 NYLON INSERT 7 803-393C NUT HEX NYLOCK M20X2.5 8 804-244C WASHER FLAT M20 PLT 9 804-247C WASHER FLAT M16 PLT 10 827-143C BUSH SPRUNG -Ø16.5XØ13.5X26.15 11 842-050C HHCS M20X2.5X160 GR8.8 12 842-051C HHCS M20X2.5X180 GR8.8 13 842-098C HHCS M16X2X90 GR8.8 SPTHD 9 Simba TL
Tine Mount - Sprung 45002 Simba TL 10
Tine Mount - Sprung Item Part No. Part Description Comments 1 603-098V SPRING PIVOT ASSEMBLY 2 603-099V SPRING TOP PLATE ASSEMBLY 3 603-240V KRAVA PIVOT BUSH 4 603-542D MAIN PIVOT 5 606-013K TINE COMPLETE-KRAVA 6 606-078D PLATE 25MM 7 800-443C ROLL PIN Ø6X50MM 8 800-444C ROLL PIN Ø10X50MM 9 803-393C NUT HEX NYLOCK M20X2.5 10 803-419C NUT LOCK M16 PHILIDAS 11 804-244C WASHER FLAT M20 PLT 12 804-247C WASHER FLAT M16 PLT 13 804-260C WASHER D75XD25X12 14 805-476C PIVOT PIN Ø30X105MM 15 807-321C SPRING Ø103MM 16 807-322C SPRING Ø60MM 17 812-424C DSGN START BLANK PART 18 812-427C TINE ARM LH 19 812-428C TINE ARM RH 20 812-429C CASTING 21 812-430C CASTING TOP PLATE 22 812-431C TINE BODY 23 827-130C BUSH SPRUNG - Ø38XØ30X34.5 24 827-131C BUSH SPRUNG - Ø44XØ36X30 25 827-133C SPRING TUBE 26 842-048C HHCS M16X2X75 GR10.9 SPTHD 27 842-050C HHCS M20X2.5X160 GR8.8 28 842-052C HHCS M20X2.5X80 GR8.8 29 842-053C HHCS M24X3X360 GR8.8 SPTHD 11 Simba TL
Tines 62003 Simba TL 12
Tines Item Part No. Part Description Comments 1 602-110C POINT - 80MM 2 803-420C NUT HEX WHIZ M12X1.75 3 820-503C C TINE - 730MM 4 820-504C SHOVEL - RH THROW 5 820-505C SHOVEL - LH THROW 6 820-506C WING 175MM LH 7 820-507C WING 175MM RH 8 842-153C PLOW M12X1.75X85 GR12.9 9 842-154C HHCS M12X1.75X60 GR12.9 13 Simba TL
Levelling Beam 62002 Simba TL 14
Levelling Beam Item Part No. Part Description Comments 1 605-017H LEVELLER BEAM - TL300 2 605-018H LEVELLER EXTENSION 3 605-019H LEVELLER BEAM ARM 4 605-020H LEVELLER BEAM - TL350 5 605-036H PIN Ø24X112 6 803-433C NUT HEX PHILIDAS M12X1.75 PLT 7 804-187C WASHER SPRING LOCK M16 PLT 8 804-246C WASHER FLAT M12 PLT 9 804-247C WASHER FLAT M16 PLT 10 805-448C LYNCH PIN CAT 1 11 842-033C HHCS M16X2X50 GR8.8 12 842-109C HHCS M12X1.75X50 GR8.8 13 891-337C TURNBUCKLE 6 CAT 0 BALL 15 Simba TL
Levelling Discs 62005 Simba TL 16
Levelling Discs Item Part No. Part Description Comments 1 605-021H LEVELLER ARM - TWIN 2 605-022H LEVELLER ARM RH 3 605-023H LEVELLER ARM LH 4 605-073D CLAMP PLATE - 200MM 5 605-077D TORSION ROD Ø40X220 6 605-078D CLAMP PLATE 145MM 7 605-080D TORSION ROD Ø40X165 8 802-976C HHCS M12X1.25X20 GR8.8 9 803-281C NUT HEX NYLOCK M12X1.75 PLT 10 803-440C NUT HEX NYLOCK M22X1.5 11 804-159C WASHER SPRING LOCK M12 PLT 12 804-246C WASHER FLAT M12 PLT 13 804-255C WASHER FLAT M24 - OD50MM 14 815-388C AGRI HUB 98-4-117 15 820-462C DISC BLADE CUT Ø460 16 842-155C HHCS M12X1.75X70 GR8.8 FTHD 17 Simba TL
Roll Frame 62004 Simba TL 18
Roll Frame Item Part No. Part Description Comments 1 601-004H ROLL FRAME 3440MM 2 601-007H CLAMP PLATE 3 601-008H 3.5M SCRAPER RAIL 4 601-009H ROLL FRAME 2940MM 5 601-015S SCJ50 BEARING COMPLETE 6 601-043H STEM - SCRAPER DDL60 CB 7 601-044H SCRAPER PLATE 8 601-111H SCRAPER RAIL 3M 9 601-150D STUB AXLE END WASHER 10 601-156V DDL550 SCRAPER 11 601-182K DDL550 2.5M ROLL ASSEMBLY FOR ROLL OPTIONS SEE PAGE 12 601-183K DDL550 3.5M ROLL ASSEMBLY FOR ROLL OPTIONS SEE PAGE 13 605-009H DEPTH ARM 14 605-012H ROLL ARM 15 605-039D PLATE 15MM 16 605-084D SHIM END BLOCK 17 605-088D PIN Ø30X120 TYPE P 18 802-611C HHCS M10X1.5X60 GR8.8 19 802-965C HHCS M20X2.5X110 GR8.8 20 802-984C HHCS M16X2X100 GR8.8 21 803-280C NUT HEX NYLOCK M10X1.5 PLT 22 803-281C NUT HEX NYLOCK M12X1.75 PLT 23 803-282C NUT HEX M16X2.00 NYLON INSERT 24 803-441C NUT HEX PHILIDAS M20X2.5 25 804-162C WASHER FLAT M10 PLT 26 804-244C WASHER FLAT M20 PLT 27 804-246C WASHER FLAT M12 PLT 28 804-247C WASHER FLAT M16 PLT 29 806-240C U-BOLT M16X2 X 101 X 145 30 806-242C U-BOLT M10X1.5 X 61 X 83 GR8.8 31 842-024C HSHCS M12X1.75X35 GR8.8 32 842-037C HSFCHCS M12X1.75X55 GR10.9 33 842-061C RHSNB M10X1.50X25 GR8.8 SPTHD 34 891-307C SHIM KIT 7 PIECE 19 Simba TL
DD Lite 550 Roller 45011 Simba TL 20
DD Lite 550 Roller Item Part No. Part Description Comments 1 601-113H ROLL TUBE 2942MM TO SUIT 3.0m MACHINE 601-134H ROLL TUBE 3440MM TO SUIT 3.5m MACHINE 2 601-374D PLATE 10MM 3 601-375D SPACER 27MM DDL 4 601-376D SPACER 58MM DDL 5 820-498C DD600 RING - 275 BORE 6 842-068C HSFCHCS M16X2X50 CSK GR10.9 21 Simba TL
Cage, HD, V & ML Rollers 45010 Simba TL 22
Cage, HD, V & ML Rollers Item Part No. Part Description Comments 1 601-110H CAGE ROLLER Ø540X2942MM TO SUIT 3.0m MACHINE 601-145H CAGE ROLLER Ø540X3440MM TO SUIT 3.5m MACHINE 2 601-250H ML ROLLER - 3.0M TO SUIT 3.0m MACHINE 601-251H ML ROLLER - 3.5M TO SUIT 3.5m MACHINE 3 601-248H V ROLLER - 3.0M TO SUIT 3.0m MACHINE 601-249H V ROLLER - 3.5M TO SUIT 3.5m MACHINE 4 601-246H HD ROLLER - 3.0M TO SUIT 3.0m MACHINE 601-247H HD ROLLER - 3.5M TO SUIT 3.5m MACHINE 23 Simba TL
Aqueel II Roller 45012 Simba TL 24
Aqueel II Roller Item Part No. Part Description Comments 1 601-132H ROLL TUBE 2900MM TO SUIT 3.0m MACHINE 604-055H ROLL TUBE 3500MM TO SUIT 3.5m MACHINE 2 601-147K AQUEEL II WHEEL- 125MM 3 601-148K AQUEEL II WHEEL- 150MM 4 601-398D RING-RETAINING 5 842-062C HSFCHCS M12X1.75X50 GR10.9 25 Simba TL
Lights - Rear 62006 Simba TL 26
Lights - Rear Item Part No. Part Description Comments 1 601-357D PLATE 12MM 2 603-563D DECAL MOUNT - SPEED 3 608-258D PLATE 6MM 4 802-997C HHCS M10X1.5X25 GR8.8 5 803-422C NUT HEX M8X2.00 NYLON INSERT 6 804-158C WASHER SPRING LOCK M10 PLT 7 804-161C WASHER FLAT M8 PLT 8 833-608C LIGHT BOARD RRH 9 833-609C LIGHT BOARD RLH 10 842-023C HHCS M8X1.25X25 GR8.8 FTHD 11 842-057C HSFCHCS M8X30 CSK 27 Simba TL
Lights - Front 62007 Simba TL 28
Lights - Front Item Part No. Part Description Comments 1 601-356D PLATE 12MM 2 608-258D PLATE 6MM 3 802-997C HHCS M10X1.5X25 GR8.8 4 803-278C NUT HEX NYLOCK M8X1.25 PLT 5 804-158C WASHER SPRING LOCK M10 PLT 6 804-161C WASHER FLAT M8 PLT 7 833-610C LIGHT BOARD FRH 8 833-611C LIGHT BOARD FLH 9 842-023C HHCS M8X1.25X25 GR8.8 FTHD 10 842-057C HSFCHCS M8X30 CSK 29 Simba TL
Tine & Levelling Disc Spacings TINE LAYOUT ( 1 : 25 ) 870 435 435 870 870 870 TINE SHOVEL PATTERN ( 1 : 30 ) 145 145 145 870 870 DISC LAYOUT ( 1 : 25 ) 743 870 870 798 TL300 - FULL ASSEMBLY DATE:- MACHINE:- SIMBA 2009 DESCRIPTION:- DRAWN:- ARH 11/12/2008 PART NO. FROM SERIAL NO. TO SERIAL NO. ASSEMBLY ISSUE AS3550 D AS3550 Simba TL 30
Tine & Levelling Disc Spacings TINE LAYOUT ( 1 : 30 ) 850 850 425 425 850 850 850 TINE SHOVEL PATTERN ( 1:30 ) 140 140 850 850 850 DISC LAYOUT ( 1:25 ) 20 954 850 850 1077 TL350 - FULL ASSEMBLY DATE:- MACHINE:- TL350 SIMBA 2009 DESCRIPTION:- DRAWN:- KSL 11/12/2008 PART NO. FROM SERIAL NO. TO SERIAL NO. ASSEMBLY ISSUE AS3551 C AS3551 31 Simba TL
Simba TL 32
Great Plains UK Ltd. Woodbridge Road, Sleaford Lincolnshire, NG34 7EW United Kingdom Tel.: +44(0)1529 304654 Fax: +44(0)1529 413468 E-Mail: simba@greatplainsmfg.com Web: www.greatplainsmfg.co.uk