Roller Shade Section Effective August 11, 2011

Roller Shade Section Effective August 11, 2011 Save a life: "Install Safety Tension Device!"

Roller Shade Measuring & Ordering Instructions Selecting the Type of Mounting: Determine whether the blind is going to be installed inside the window frame or outside the window frame. Inside Mount (IB): I room. Measuring the and the Length for Inside Mount: For the width, measure across the top, middle, and bottom of the window opening. Using the narrowest dimension, measure to the nearest 1/8. By using the narrowest measurement the shade will operate correctly. For the length, measure the up and down dimension on the left, center, and right side. Use the longest length measurement, measuring to the nearest 1/8. The factory will make any appropriate deductions. Do not make any width deductions. Outside Mount (OB): Outside mount installations are mounted on the wall or on the window molding. It is best to overlap the window opening at least ¾ on each side when measuring for roller shades. Measuring the and the Length for Outside Mount: Measure the area that the shade is to cover. For roller shades it is recommended to overlap the window opening by at least ¾ on each side for a total of 1 ½. To allow for enough space for the mounting brackets and to cover the bottom of the window, the suggested overlap for a roller shade depends on the size of the shade and the valance option if required. If the window opening has a sill, measure from where the top of the shade will be located to the top of the window sill. Note: When outside mount blinds are specified, no factory deductions are taken from the bracket to bracket measurement. There will be a fabric deduction as outlined on page 2. Confirming Measurements: The most common error in ordering blinds is reversing the width and the length measurements. Always confirm that the width is the measurement that goes across from left to right and that the length is the measurement that goes from top to bottom. Clutch & Bracket Selection: To determine the clutch and bracket size used by the factory for a specific shade, refer to the Manual Clutch Fabrication Chart at the end of the roller shade section of the suggested retail price book. Bracket Dimensions: Ceiling Mount Installation Wall Mount Installation Clutch & Bracket Used Projection Height Projection Height 1 ¼ M8 Clutch Bracket 1 7/8 2 3/8 2 3/8 1 7/8 1 ½ M16 Clutch Bracket 2 7/8 2 5/8 2 5/8 2 7/8 1 ¾ M24 Clutch Bracket 3 1/4" 3 3 3 1/4" 3 Fascia M-Series Bracket 3 3 3 3 4 Fascia M-Series Bracket 4 4 4 4 Standard Motor Bracket 2 1/2" 2 7/8 2 7/8 2 1/2" Platinum Clutch Bracket 3 3 3/4" 3 1/4 3 3/4" Bracket Shown as used in Wall Mount Installation Estimated Shade Roll-Up Diameters: Refer to the chart below to calculate the approximate roll-up diameter for the given shade drops. Clutch Shade Clutch Shade Motorized Shade Motorized Shade Shade Drop with 1 ½ Tube with 1 ¾ Tube Shade Drop with 2 ½ Tube with 3 Tube 60 ±2.250 ±2.500 60 ±3.125 ±4.000 72 ±2.375 ±2.625 96 ±3.250 ±4.125 84 ±2.500 ±2.750 120 ±3.500 ±4.250 96 ±2.625 ±2.875 144 ±3.625 ±4.375 120 ±2.750 ±3.000 : 168 ±3.750 ±4.500 132 ±2.875 ±3.125 192 ±3.875 ±4.625 144 ±3.000 ±3.250 216 ±4.000 ±4.750 156 ±3.250 ±3.500 240 ±4.250 ±5.000 (1)

Critical Information: Shade Cloth Deductions & Light Gap: (All Measurements provided should be Bracket to Bracket!) It is extremely important to note when measuring for roller shades that the actual fabric width of the shade will be less than the window measurement provided. To allow for the space that shade brackets, clutch or motor, and idler end take up, the factory must make a deduction so that the finished measurement or bracket to bracket measurement of the shade fits into the width dimension provided by the customer. Please note the below deductions taken by the factory on all shades. Inside Mount Deduction: An additional 1/4" deduction will be taken for shades with fascia ordered as an inside mount Deductions Explanation M-Series Clutch Spring Loaded Shades 1 1/4 1 1/4 The fabric width measurement will be 1 1/4 less than the ordered width. The Fabric width measurement will be 1 1/4 less than the ordered width. Platinum Series Clutch 1 3/8 The fabric width measurement will be 1 3/8 less than the ordered width Battery (LT30) or Low Voltage Motor (ST30) 1 1/4 The fabric width measurement will be 1 1/4 less than the ordered width. AC Hardwire Plug-In Motor (LT50 & ST50) 1 7/8 The fabric width measurement will be 1 7/8 less than the ordered width. Please Note: When shades with a Fascia are ordered inside mount, an addition 1/4 deduction will be taken for the fabric width. Please Note: When shades with a Pocket L Fascia are ordered inside mount, an addition 3/8 deduction will be taken for the fabric width. Shade Measurements: (Critical Note!) Specify bracket to bracket width measurements for all roller shade orders. Do not provide fabric width measurements. If a specific shade cloth width is required, please refer to the list of shade cloth deductions above and add the required amount to the fabric width. Fabric Telescoping & Tracking: Roller shades that exceed a 3-to-1 length to width ratio where the shade is more that 3 times longer than it is wide, may have problems tracking or rolling up straight. This tracking problem, commonly referred to as telescoping is an inherent characteristic of roller shade fabrics and should be explained to the end user. Railroading & Fabric Seams: In order to make a shade that is wider than the width of the roll, the fabric will be railroaded or turned sideways and cut to the width of the shade. In cases where the shade is wider and longer than the width of the fabric roll, a second piece of fabric will be cut and welded or spliced to the first fabric piece. This weld, which secures the two pieces of fabric together, creates a visible seam. When a splice is required, the factory will place the seam as high on the shade as possible. If a custom splice location is desired, please specify the seam location from the bottom of the shade up. Please allow ± ½ tolerance when custom seam locations are requested. Roll Direction: Regular Roll or Reverse Roll? Regular Roll: Regular roll shades indicate when the shade fabric rolls off of the back of the roller tube. The shade cloth will be closest to the window with this option. Reverse Roll: Reverse roll shades indicate when the shade fabric rolls off of the front of the roller tube. The shade cloth will be furthest away from the window with this option. Glass Glass Regular roll shades are industry standard and yield the highest levels of energy conservation because of the shade s close proximity to the glass. Reverse roll shades are most commonly used for the following applications: To avoid a window obstruction (door handle, etc.) To reduce light gap for corner or bay windows (2)

Manual Roller Shade: M-Series Chain Operated Clutch Standard M-Series Clutch Roller Shade Exploded Diagram (Shown with Fascia Brackets) The M-Series Clutch Glass Reinforced Resin to Increase Durability Precision Engineered Gear for Qualified Bead Chain High Impact Plastic Advanced Spring Technology for Smooth Operation Standard M-Series Clutch Roller Shade This roller shade is operated manually with a heavy-duty, self-lubricating clutch mechanism. With a continuous loop control chain, shades can be rolled up, exposing a room to sunlight, or down, filtering light from entering a room. Control chain is available as white (plastic), black (plastic), stainless steel (surcharge will apply) white stainless steel (surcharge will apply), and black stainless steel (surcharge will apply). (Shown with Standard Non-Brackets) Standard Clutch Roller Shade Surcharges: Stainless Steel Chain $ 12.00 per shade White or Black Stainless Steel Chain $ 24.00 per shade Spring Assisted Lift $125.00 per shade Spring Assist Mechanisms are required for oversized shades. Please refer to the clutch & tube fabrication chart at the back of this section for more details. Fabric Wrapped Hembar $ 15.00 per shade External Painted Hembar $ 10.00 per shade Exterior Guide Wire System $120.00 per shade Minimum : 8 Maximum : 126 Minimum Height: 8 Maximum Height: 144 (3)

Manual Roller Shade: Platinum Series Contract Chain Operated Clutch Platinum Series Contract Clutch Roller Shade Exploded Diagram (Shown with Ceiling Mount Installation Brackets) Platinum Series Clutch Wall Mount Installation Brackets Left-Hand Control Wall Mount Installation Brackets Right-Hand Control Wall Mount Installation Brackets Platinum-Series Contract Clutch Roller Shade The heavy-duty chain operated clutch mechanism allows one to position the roller shade with precise accuracy. The bi-directional clutch never needs adjustment. When the operator stops pulling on the bead chain, the clutch stops automatically, holding the shade in the exact position desired. The Platinum Series Contract clutch mechanism is manufactured from PA6 with glass fiber. Control chain is available as standard stainless steel. White and black stainless steel chain is available for a surcharge. Platinum Clutch Roller Shade Surcharges: Platinum Clutch with Stainless Steel Chain $ 10.00 NET per shade White or Black Stainless Steel Chain $ 24.00 per shade Spring Assisted Lift $125.00 per shade Spring Assist Mechanisms are required for oversized shades. Please refer to the clutch & tube fabrication chart at the back of this section for more details. External Painted Hembar $ 10.00 per shade Minimum : 8 Maximum : 108 Minimum Height: 8 Maximum Height: 144 (4)

Manual Roller Shade: Cordless Spring Lift Spring Roller Shade This roller shade is operated by a heavy-duty spring mechanism. By pulling on a draw cord tassel attached to the hembar, shades can be rolled up, exposing a room to sunlight, or down, filtering light from entering a room. Minimum : 20 Maximum : 78 Minimum Height: 18 Maximum Height: 78 Motorized Roller Shade: RTS Wirefree Battery Powered Battery Powered Motorized Roller Shade This roller shade is operated by a battery powered motor system. At the press of a button, shades can be rolled up, exposing a room to sunlight, or down, filtering light from entering a room. This unique motor system has full lift control of shades that are up to 12.5 lbs. The motor is powered by AA lithium battery packs, which can be concealed within a valance, mounted to the ceiling, or installed to the wall. The battery life expectancy is 1 to 2 years (based upon 4 operations per day and the weight of the shade). Battery powered roller shades are available with radio frequency controls. Shades may be operated as an individual unit, as sub-groups, and as an entire group. Please consult Mariak technical support with any questions you may have. Battery Powered Roller Shade Surcharges: Batteries are included with motors & controls. RF Battery Motor 12-volt $625.00 per shade (For shades up to 12.5lbs.) Radio Frequency Transmitter 1-Ch $140.00 Radio Frequency Transmitter 5-Ch $175.00 Radio Frequency Transmitter 16-Ch $515.00 Radio Frequency Wall Switch 1-Ch $320.00 Radio Frequency Wall Switch 5-Ch $340.00 Radio Frequency 24-Hour Chronis Timer $360.00 Radio Frequency Sunis Interior Sun Sensor $410.00 Radio Frequency 16 Ch Interface for Automation Integration $900.00 Minimum : 14 Maximum : 96 Minimum Height: 18 Maximum Height: 96 RF Hand-Held Transmitters & Wireless Wall Switches are available in 1 & 5 Channel models Critical Note: Included in the surcharge for a Battery Motorized Shade is a set of Dual Battery Packs with 16 AA Lithium Batteries. Battery Packs Mounted to the Top of the Window Jam (5)

Motorized Roller Shade: RTS Plug-In (AC & DC options) Plug-In/Radio Frequency (RTS) AC & DC Motorized Roller Shade Motorization Made Simple! Depending on the size and electrical wiring available, this roller shade is operated by either a 110-volt AC 3-wire motor or a 24-volt DC 2-wire motor. This scenario requires the motor to be plugged-in to a standard 3-prong electrical wall outlet. For your convenience, if a 110-volt AC motor is selected, the shade is shipped from the factory with a plug installed at the end of the motor cable. If so desired, the plug may be cut off and hardwired to a dedicated power supply by a licensed electrician. If the 24-volt DC motor is specified, you will need to wire the power supply transformer to the motor cable. Plug-in motors have a built-in radio frequency receiver that communicates with a variety of remote control transmitters via radio waves. At the push of a button, shades can be rolled up, exposing a room to sunlight, or down, filtering light from entering a room. The electronic controls for plug-in motorized roller shades are capable of operating a shade individually, as sub-groups, and/or as an entire group. Please consult Mariak technical support with any questions you may have. 110-Volt AC Motorized Shades 24-Volt DC Motorized Shades Minimum : 29 Minimum : 18 Maximum : 240 Maximum : 96 Minimum Height: 18 Minimum Height: 18 Maximum Height: 240 Maximum Height: 96 Plug-In/Radio Frequency Motorized Roller Shade Surcharges: Please note that Radio Frequency motors have 3-wire conductor cables. These motors may be hardwired or plugged into a 3-prong electrical outlet. 110v AC Somfy RTS Motor Options: Radio Frequency Sonese 50 RTS Motor 504 Model $ 755.00 per shade (For shades up to 25lbs.) Radio Frequency Altus 50 RTS Motor 506 Model $ 815.00 per shade (For shades up to 35lbs.) Radio Frequency Altus 50 RTS Motor 510 Model $ 935.00 per shade (For shades up to 60lbs.) RF Hand-Held Transmitters & Wireless Wall Switches are available in 1 & 5 Channel models 24v DC Somfy RTS Motor Options: (Power supply transformers are required for DC Motors) Radio Frequency Sonese 30 RTS Motor $ 755.00 per shade (For shades up to 15lbs.) 1.66amp Power Supply (Powers 1 24v motor) $ 42.86 NET 5.00amp Power Supply (Powers up to 3 24v motors) $ 172.81 NET 10.0amp Power Supply (Powers up to 6 24v motors) $ 335.66 NET 15.0amp Power Supply (Powers up to 9 24v motors) $ 416.46 NET 20.0amp Power Supply (Powers up to 12 24v motors) $ 975.86 NET (Critical Note: Power Supply are only required when ordering 24-volt DC motors. Do not order power supplies with 110-volt motors). Somfy Altus RTS Control Systems: (Selected at least 1 Transmitter or Wall Switch) Radio Frequency Transmitter 1-Ch $140.00 Radio Frequency Transmitter 5-Ch $175.00 Radio Frequency Transmitter 16-Ch $515.00 Radio Frequency Wall Switch 1-Ch $320.00 Radio Frequency Wall Switch 5-Ch $340.00 Radio Frequency 24-Hour Chronis Timer $360.00 Radio Frequency Sunis Interior Sun Sensor $410.00 Radio Frequency 16 Ch Interface for Automation Integration $900.00 Plug-In Motors Plug Into a Standard Electrical Outlet located somewhere close to the motor. 110-volt AC Plug-In Motors simply plug directly into a standard electrical outlet 24-volt DC Plug-In Motors require a power supply transformer that is wired to the motor cable and then plugs into an electrical outlet (6)

Econoline Motor Mariak Industries Inc. introduces the Econoline Motor exclusively designed and produced for the North American Market. Features include: Quiet Motor 110 Volts 115 Watts AC Plug-In Motor Only with 6 Cord 6 Newton Motor Strength Radio Control Lifting Capacity of 50 Pounds (Approximately 15 x 12 depending on fabric weight) Programmable from Remotes 3 available (Wall Switch Not Available) Diameter 35mm 5 Year Limited Lifetime Warranty Durability Fits 2 and 3 Mariak Tube Quiet Rubber Drive 20 Motor Body Allows for Narrow Shade Installation Motor Works with Universal Bracket - 10 mm Square Stud Speed 34 rpm Thermal Time 4 Minutes Maximum Operable Temperature 40 C = 104 F Power Consumption 0.96A RF Antenna External Motor Cord Length with Nema Plug 6 Feet Light Gap 7/8 on each side Minimum Shade 23-1/2 Wide 110v AC Mariak Econoline Motor Options: o Radio Control Plug-In Motor with 6 cord & Nema Plug $ 540.00 per shade o 1-Channel Econoline Transmitter $ 60.00 each o 6-Channel Econoline Transmitter $ 150.00 each o 16-Channel Econoline Transmitter $ 250.00 each Programmable from One, Six or Sixteen channel remote. (7)

Motorized Roller Shade: In-Wall Hardwired In-Wall Hardwired Motorized Roller Shade This roller shade is operated by a 110-volt AC 4-wire motor. It requires the motor to be hardwired or installed such that the power supply must be fixed and permanent. In other words, wires from a power source within the wall must be connected by a licensed electrician so that the motor receives a constant power supply at all times. At the push of a button, shades can be rolled up, exposing a room to sunlight, or down, filtering light from entering a room. The electronic controls for hardwired motorized roller shades are capable of operating a shade individually, as sub-groups, and/or as an entire group. Please consult Mariak technical support with any questions you may have. Minimum : 29 Maximum : 240 Minimum Height: 24 Maximum Height: 240 Hardwired Standard Motorized Roller Shade Surcharges: Please note that Hardwired Standard motors have 4-wire conductor cables. Motor Options: (Select one motor per shade) Somfy Sonese Standard Hardwire Motor 504 Model. $655.00 per shade (Silent Motor for shades up to 25lbs.) Somfy LT50 Standard Hardwire Motor 506 Model $655.00 per shade (For shades up to 35 lbs.) Somfy LT50 Standard Hardwire Motor 510 Model $735.00 per shade (For shades up to 60 lbs.) Motion Control (MCS) Hardwired Motor 506 Model.. $550.00 per shade (For shades up to 35lbs.) Motion Control (MCS) Hardwired Motor 512 Model. $700.00 per shade (For shades up to 60lbs.) Standard Paddle Wall Switches: Maintained SPDT Wall Switch $ 65.00 (For individual motor control, 1 required per motor) Maintained DPDT Wall Switch $130.00 (For group control of 2 motors, 1 required for 2 motors) Additional Hardwired Motor Accessories: Plug Disconnect w/wall Entry Plate.. $ 32.00 net There are a number of hardwired motor control options. Please consult Mariak technical support so that we may help you create the best solution for your job requirements. In-Wall Hardwired with Plug Disconnect (Plug Disconnect is available for an additional charge) Example of Plug Disconnect (8)

Roller Shade Valance Options: 3 & 4 Square Aluminum Fascia Valance The 3 & 4 Square Aluminum Fascia Valance is an L shaped aluminum extrusion that covers the front and bottom of the roller. This valance option locks to its brackets with snapin fittings. The roller is concealed behind this valance and the bottom of the shade drops from the back of the valance when lowered. Roll: Available for regular roll only Color: White, Alabaster, Bronze, Black, & Clear Anodized Mount: Inside or Outside Minimum : 18 Maximum : 240 Pricing: Please refer to Suggested Retail Tables for Pricing. 3 & 4 Round Aluminum Fascia Valance The 3 & 4 Round Aluminum Fascia Valances are an aluminum extrusion that offers a contoured face presenting a softer appearance than tradition square fascias. This valance option covers the front and bottom of the roller and locks to its brackets with snap-in fittings. The roller is concealed behind this valance and the bottom of the shade drops from the back of the valance when lowered. Roll: Available for regular roll only Color: White, Black, & Clear Anodized Mount: Inside or Outside (Recommended as Outside) Minimum : 18 Maximum : 240 Pricing: Please refer to Suggested Retail Tables for Pricing. 3 & 4 Fabric Wrapped Fascia Valance The 3 & 4 Fabric Wrapped Fascia Valances are the Round Aluminum Fascia Valances listed above, but include fabric matching the roller shade wrapped around the aluminum extrusion. This innovative upgrade option provides a warm look for any room. As described above with the Round Fascia Valance, this option covers the front and bottom of the roller and locks to its brackets with snap-in fittings. The roller is concealed behind this valance and the bottom of the shade drops from the back of the valance when lowered. Roll: Available for regular roll only Color: Valance fabric matches shade fabric Mount: Inside or Outside (Recommended as Outside) Minimum : 18 Maximum : 240 Pricing: Please refer to Suggested Retail Tables for Pricing. Inserted Fabric Valance The Inserted Fabric Valance is a traditional dust cover vertical blind valance that uses 3 ½ strips of roller shade fabric inserted into the groover channel of the valance. This valance features a continuous corner return that prevents the valance returns from separating from the valance. Roll: Available for regular roll & reverse roll shades Color: Valance fabric matches shade fabric Mount: Inside or Outside Minimum : 18 Maximum : 192 Pricing: Please refer to Suggested Retail Tables for Pricing. (9)

Mariak Commercial Roller Shade Cassette For quick and easy installations in commercial buildings Mariak offers the Commercial cassette. Flat front fascia offered in 4 colors easily blends with internal structural shapes of commercial buildings offering at the same time esthetically pleasing, easy to maintain closure for the roller shade. Snap on brackets provide quick and easy on-site installation. Commercial quality clutch can be placed on either side of the cassette. Height adjustable idler end of the cassette allows for leveling correction without need for shims. Cassette size 3 1/8 by 4 high easily fits inside typical window opening. ngs Mariak offers the Commercial cassette. Flat front fascia offered in 4 colors Roll: Available for regular roll only Fascia Color: White, Black, Alabaster, Bronze Or Anodized Bracket Plate: Mill Finish Mount: Inside or outside Clutch: CS Clutch 16lb Idle side: Adjustable height position Motor: DC Control: Tube: Right or Left 1-1/2 Tube up to 96 Wide 1-3/4 Tube up to 114 Wide Minimum : 20 Minimum Length: 20 Maximum : 114 Maximum Length: 120 Quick and easy installation Adjustability and Leveling Correction Sleek design accommodates upscale commercial needs Heavy-Duty Platinum Clutch Maximum shade diameter: 2-5/8 Front Fascia has a high quality finish that is highly resistant to abrasion and corrosion and is available in five of the most popular colors. Optional one piece bracket plate available up to 36. Mariak Residential Roller Shade Cassette For applications requiring elegant contemporary looks Mariak Industries Inc. offers a cassette. Curved front profile nicely blends with many interior decorating styles. Aluminum 3 ½ by 3 ½ extrusion provides space for roll of fabric up to 3 inches in diameter. Snap-on mounting brackets allow for quick installation. Front of the cassette can be finished with the shade fabric. Internal brackets allow the cassette to be used with 15lb clutch or DC motor. assette to be used with 15lb clutch or DC motor. Roll: Available for regular roll or reversed roll Color: Anodized, Alabaster, Black, Bronze or White Mount: Inside or outside Clutch: SL 15 Motor: DC Control: Right or Left Minimum : 20 Minimum Length: 20 Maximum : 96 Maximum Length: 120 Quick and easy installation Sleek look accommodates upscale commercial needs and affords greater residential appeal Sleek, curved design makes sunscreen fabrics more adaptable to residential use Intermediate bracket allows two shades in one headrail Available in five high quality powder coated paint finishes which is highly resistant to scratches and abrasion. Up to 96 x 120 inch,16 Mil fabric thickness on 1-1 /2 inch (38mm)tube Affords upscale, finished look No visible brackets Intermediate bracket allows two shades in one headrail Great for patio doors Fabric insert option (10)

Roller Shade Valance Options: Ceiling L Fascia Valance The Ceiling L Fascia Valance is an aluminum extrusion that covers the top and front of the roller. If installed as an inside mount, one should drill though the top of the fascia into the ceiling. If installed as an outside mount, one should screw heavy duty angle irons to the top of the valance and then secure the angle irons firmly to the wall. To conceal the bottom of the roller, a Bottom Closure Plate is available. See price table for surcharge. Roll: Available for regular roll & reverse roll shades Color: White, Black, & Clear Anodized Mount: Inside or Outside Minimum : 18 Maximum : 240 Dimensions: 4 ½ x 4 ½ Ceiling L Fascia Closure Plate Pricing: Please refer to Suggested Retail Tables for Pricing. Shade Pocket Valance without Ceiling Tile Receiver Lip The Shade Pocket Valance is an aluminum extrusion that covers the top, front, and back of the roller. If installed as an inside mount, one should drill though the top of the fascia into the ceiling. If installed as an outside mount, heavy duty brackets are provided. To conceal the bottom of the roller, a Bottom Closure Plate is available. See price table for surcharge. Roll: Available for regular roll & reverse roll shades Color: White & Clear Anodized Mount: Inside or Outside Minimum : 18 Maximum : 240 Dimensions: 5 ½ x 5 ¼ Pricing: Please refer to Suggested Retail Tables for Pricing. Shade Pocket Valance with Ceiling Tile Receiver Lip The Shade Pocket Valance is an aluminum extrusion that covers the top, front, and back of the roller. If installed as an inside mount, one should drill though the top of the fascia into the ceiling. If installed as an outside mount, heavy duty brackets are provided. To conceal the bottom of the roller, a Bottom Closure Plate is available. See price table for surcharge. Roll: Available for regular roll & reverse roll shades Color: White & Clear Anodized Mount: Inside or Outside Minimum : 18 Maximum : 240 Dimensions: 5 ½ x 5 ¼ Pricing: Please refer to Suggested Retail Tables for Pricing. (11)

Roller Shade Valance Options: Dual Shade Pocket (Headbox) Valance The Dual Shade Pocket Valance is an aluminum extrusion that covers the top, front, and back of a dual roller shade system. If installed as an inside mount, one should drill though the top of the fascia into the ceiling. If installed as an outside mount, heavy-duty brackets are provided. To conceal the bottom of the roller, a Bottom Closure Plate is available. Roll: Available for regular roll & reverse roll shades Color: White Mount: Inside or Outside Clutch: M16 or M24 Motor: AC or DC Minimum : 18 Maximum : 240 Dimensions: 7 Deep x 9 Tall Mount Strip Wall Hanger with Closure Plate The Mount Strip Wall Hanger with Closure Plate is an aluminum extrusion that is installed at the bottom of a dry soffit to conceal bottom the roller. One should drill the Mount Strip Wall Hanger in the front of the drywall soffit (pocket). See price table for surcharge. Roll: Available for regular roll & reverse roll shades Color: Mount Strip Mill Finish; Closure Plate White, Black Clear Anodized Mount: Inside Minimum : 8 Maximum : 240 Closure Dimension: 3 Pricing: Please refer to Suggested Retail Tables for Pricing. 2.125 High 3 Wide (12)

Roller Shade Hembar & Channel Options: Pocket Bottomweight Hembar (Standard) The Pocket Bottomweight Hembar is an aluminum extrusion welded into a pocket made by folding over the fabric at the bottom of the roller shade. This type of hembar is commonly referred to as a concealed hembar and is standard on roller shades. Size: 1 ⅜ tall External Hembar The External Hembar is an exposed, hollow aluminum extrusion secured to the bottom of the roller shade fabric. The ends are covered with plastic, color coordinating caps that are fixed in place with screws. This hembar option is available in white, black, bronze, and clear anodized finishes. The Wrapped Hembar is required when hold-downs are requested. Upgrade Surcharge: External Hembar $ 10.00 per shade Wrapped Hembar The Wrapped Hembar is an exposed aluminum extrusion in which the shade fabric is wrapped around the front of the hembar locked into place at the top and bottom of the extrusion. The Wrapped Hembar is required when hold-downs are requested and is required for the exterior shade guide wire system. Upgrade Surcharge: Fabric Wrapped Hembar $ 15.00 per shade Side & Sill Channels Side and Sill Channels are a 2-piece U shaped aluminum extrusion used to eliminate light gaps at the right, left, & bottom edges of the shade. These channels are primarily used for applications where complete blackout of light is desired. Installation is quite simple. One should drill the wall of channel part A into the sheet rock or wood frame of the window opening. Then, channel part B can be easily snapped to part A. Roll: Available for regular roll & reverse roll shades Color: White, Alabaster, Bronze, Black, & Clear Anodized Mount: Inside or Outside Minimum Length: 18 Maximum Length: 240 Dimensions: 2 1/8 x 1 Shade Cloth (Side & Sill Channels Eliminate Edge & Bottom Light Gap) Pricing: Please refer to Suggested Retail Tables for Pricing. Side Channel Sill Channel (13)

Multiple-Banded Coupled Motorized Roller Shades: Multiple-Banded Coupled Motorized Shades: A multiple-banded shade is a set of individual shades (generally 2 to 5 fabric bands) that are connected together by shade coupler brackets. These fabric bands are all run off of an individual motor. In other words, 1 motor can operate anywhere from 2 to 5 shade bands at one time. Please note that for this application, shades cannot be controlled individually; each set of coupled shades will always raise and lower together in unison. A multiple-banded shade application reduces the number of motors required for a given job and eliminates additional wiring expenses that might have been required for additional motors. Note: The maximum size of the overall shade and the number of shade bands is subject to weight limitations of an individual motor. Positive Reasons for using Multiple-Banded Shades: Reduction of motor costs Reduction of electrician costs Break up very large shades into smaller ones Negative Reasons for not using Multiple-Banded Shades: More complex bracket installation Group control of shades only All shades must be the same height Pricing: Multi-band shades are priced by adding the shade price for each band together. Then separately and add together 1. Price each band separately and add together 2. Price each coupler surcharge and add together a. Straight Line Coupler Bracket Surcharge $100.00 per Coupler b. Corner Coupler Bracket Surcharge (90 o Adjustable) $200.00 per Coupler 3. Add shade band and coupler prices together Straight Multiple-Banded Shade System: Straight Coupler Bracket Shade Band Shade Band Shade Band Shade Band Motorized Shade Light gap between shade bands is approximately 3/4 on straight multiple band shade systems. On a Multiple-Banded Corner Shade, Multiple-Banded all shade bands will Shade always System raise and lower together. L i g h t G a p Corner Multiple-Band Shade System: Corner Coupler Brackets are Adjustable from 5 o to 90 o (14)

Roller Shade Specialty Options: Indexable Coupler 12mm Spring Loaded & Retractable Brackets are adjustable on the height. Long & Stable No friction as the shaft rolls on ball bearings. Indexable (i.e. The height of the shades can be adjusted by pulling the outer sleeve of one side of the coupler which has teeth every 1/8 and makes sure that shades look level.) Calibrated dial as a guide (male coupler) Maintains equal light gap throughout the shade. Retractable function for easy installation (female coupler) Fits 2"Motor Tube, 2" grooved Motor and 2-3/8" round tube. Adjustable Idler Fascia Brackets for both Clutch Operated & Motorized Shades: Installing roller shades has never been so easy. The new and improved Dura-Roll fascia bracket allows an installer to level the roller shade without removing and re-installing brackets. By removing a small allen wrench that is provided on the inside of each bracket, one can raise or lower the idler pin end of the roller shade with a simple turn of a basic set screw. This set screw is located at the bottom opening of the fascia bracket. This adjustable idler bracket is available with clutch operated or motorized shades ordered with 3 Fascia or 4 Fascia valances. Clutch Roller Shade with Spring Assist Lift Mechanism: Roller shades using a spring assist lift mechanism reduce the amount of pull force required to lift heavier shades. This system is adaptable for left or right hand installations and can be used for either regular or reverse roll shades. Spring Assisted Shades $125.00 per shade Please refer to the Clutch/Tube fabrication table at the back of this section to determine when a Spring Assist Lift Mechanism is required. Shades with Spring Assist Mechanisms are available for both right and left hand control. Recommended Sizes: Minimum : 60 Maximum : 126 Minimum Height: 60 Maximum Height: 144 (15) Spring Assist Clutch Lifting Mechanism

M-Series Roller Shade Specialty Options: Multiple-Band M-Series Clutch Roller Shade: This type of roller shade joins two fabric bands and allows operation a single control chain. This intermediate bracket uses a sealed roller bearing with recessed end caps to reduce light gap between the two fabric panels. Fascia is not available with this option. Note: Surcharge: Due to weight constraints, a maximum of two shades bands can be controlled from a single control chain. Available for use with both 1 ½ and 1 ¾ clutch mechanisms. 1 Light-Gap at the Center Bracket $15.00 NET per Coupler Bracket Minimum : 16 Maximum Combined : 96 Minimum Height: 8 Maximum Height: 96 M-Series Clutch Roller Shade with Center Support Bracket: This specially designed bracket joins two separate roller shades together. It allows operation of two independently operated shades with two controls chains. The right chain operates the right shade, while the left chain operates the left shade. This center support bracket uses two recessed spring loaded end caps to reduce light gap between the two separate roller shades. Fascia is not available with this option. Note: Surcharge: Available for use with both 1 ½ and 1 ¾ clutch mechanisms. $15.00 NET per Center Support Bracket Minimum : 16 Maximum Combined : 192 Minimum Height: 8 Maximum Height: 96 How to measure for a Multiple-Band Roller Shade: Measure from outside-bracket to outside-bracket to get the overall width. Measure from the left edge to the center point; then measure from the center point to the right edge. (16)

M-Series Clutch Roller Shade Dual Shade Options: M-Series Clutch Double Roller Shade without Fascia: This type of roller shade allows installation of a sunscreen fabric shade and a blackout shade on a single mounting bracket providing both light filtering and room darkening. The compact design of this bracket permits two shades to fit in a smaller room projection than two individually installed shades on the same window. Bracket Dimensions: 4 ½ x 4 ½ Control Option: Both Front & Back Shades with Left Side Controls Both Front & Back Shades with Right Side Controls Front & Back Shades with Opposite Side Controls Double Bracket Surcharge: $20.00 per pair (Net Not Discountable) Note: Available for use with 1 ½ clutch mechanism only. Note: Available in White only. When installing double shade brackets as a wall mount application, the front roller shade must be ordered as a reverse roll! Minimum : 8 Maximum : 96 Minimum Height: 8 Maximum Height: 96 M-Series Clutch Double Roller Shade with 4 and 7 ½ Square Fascia: This type of roller shade allows installation of a sunscreen fabric shade and a blackout shade on a single mounting bracket providing both light filtering and room darkening. The compact design of this bracket permits two shades to fit in a smaller room projection than two individually installed shades on the same window. Bracket Dimensions: Finishes: Control Option: 4 Fascia 4 tall x 5 ¾ Deep 7 ½ Fascia 7 ½ tall x 5 ¾ Deep White, Bronze & Clear Anodized Only Both Front & Back Shades with Left Side Controls Both Front & Back Shades with Right Side Controls 4 Double Fascia Bracket Surcharge: $30.00 per pair (Net Not Discountable) Note: Available for use with 1 ½ M16 clutch mechanism only. 7 1/2 Double Fascia Bracket Surcharge: $60.00 per pair (Net Not Discountable) Note: Front shade uses 1 ¾ M24 clutch; back shade uses 1 ½ M16 clutch. Note: 7 ½ Fascia is only available in White, Bronze, and Clear Anodized 4 Fascia 7 ½ Fascia Minimum : 8 8 Maximum : 96 144 Minimum Height: 8 8 Maximum Height: 96 156 Dual Clutch Shade with 4 Square Fascia (Shown without End Caps) (17) Dual Clutch Shade with 4 Square Fascia (Shown with End Caps)

110-Volt AC Double Motorized Roller Shade Options: Dual Motorized Shade without Fascia (Typically installed into a pocket built into the ceiling) 5 7 ½ AC Dual Motorized Shade System with 7 ½ Square Fascia Dual Motorized Shade with 7 ½ Square Fascia This type of roller shade allows installation of a sunscreen shade and a room darkening shade on a single mounting bracket providing both light filtering and light blocking. The compact design of this bracket permits two shades to fit in a smaller room projection than two individually installed shades on the same window. Roll: Available for regular roll only Color: White, Bronze, & Clear Anodized Mount: Inside or Outside Minimum : 36 Maximum : 126 Minimum Height: 24 Maximum Height: 192 Pricing: Please request quotation. (18)

Fabric Attachment Roller System: Secure Grip Spline The Secure Grip Spline Fabric Attachment System was designed with several purposes in mind. This technique was engineered to establish an effective process for securing the shade cloth to the aluminum roller shade tube. Its unique shape and composition lock the shade cloth in place, thus preventing it from falling off the tube, a common problem found when double face tape or glue techniques are applied. The Secure Grip Spline creates an effective method for keeping the shade cloth straight as it rolls up on the roller shade tube. This system substantially reduces the amount of telescoping (the spiral motion that occurs when a shade is rolling up) that is caused when the shade brackets are installed improperly. The Secure Grip Spline was developed such that it provides for easy fabric removal and reinstallation. Should the fabric require cleaning or should the customer desire a new shade cloth, the material can be removed with ease without having to remove the roller shade tube from its brackets. Universal Drive Tension Device Mariak is proud to introduce our new Universal Drive Tension Device. This child safety device has been engineered to lock the cord/chain if it is not installed to the wall or if it comes loose from the mounting surface. The locking mechanism will render the shade inoperable until the safety device is reattached properly in compliance with ANSI/WCMA standard section 6.5.2. Once installed, the Cord/Chain Safety Locking Tensioner is designed to allow the chain connector and/or stop bead to pass easily through the opening. In compliance with the latest manufacturing safety guidelines (ANSI/WCMA standard section 6.5.2) Mariak Window Fashions includes with each fully-assembled product warning tags, warning labels, safety devices and cord cleats. Installers of the finished product must adhere to the safety guidelines as established by the installation instructions and by using all devices provided by the manufacturer. It is the responsibility of the installer, as well as the end consumer, to see that all safety devices are properly installed according to the manufacturers installation instructions included with each device and remain so throughout the life of the product. Mariak Window Fashions is not liable for injuries or fatal occurrences related to improper installation or maintenance of required safety devices. (19)

Skylight, Standard with Snap-On Side Channels For small Skylight applications Mariak Industries Inc. offers motorized and crank driven solutions. An L shaped 4 ½ by 4 ½ aluminum extrusion creates main body of the skylight and covers the back and bottom of the assembly. The inside portion on both sides of the extrusion is closed with the closure plate. The top portion of the assembly is covered with 5 wide top plate. Two driving options are available to move roller shade back and forth. Motorized option uses AC motors while the manual option uses heavy duty crank mechanism with a 7:1 turning ratio and a detachable arm. Both option come with two-piece 2 ½ by 1 side channels on both ends. Please contract Mariak for a price quote. a detachable arm. Both option come with two-piece 2 ½ by 1 side channels on both ends. Roll: Available for regular or reversed roll Minimum : 30 Color: White Maximum : 60 Mount: Inside Minimum Length: 30 Clutch: Crank Maximum Length: 96 Motor: AC Wires: Right or Left Standard Crank Driven Skylight Standard Motorized Skylight Cross Section of Standard Motorized Skylight Premium Skylight with adjustable side channels For large Skylight applications Mariak Industries Inc. offers Premium Motorized Skylight. The shade fabric for this product is constantly tensioned from both sides along the entire distance of travel. An L shaped 4 ½ by 4 ½ aluminum extrusion provides space for both the fabric and motor. For skylights longer than 96 inches, a U shape 7 by 9 extrusion is used to cover motor and fabric side of Skylight. Please contract Mariak for a price quote. Roll: Available for regular roll only Minimum : 30 Color: White Maximum : 144 Mount: Inside Minimum Length: 30 Motor: AC Maximum Length: 180 Wires: Right or Left For large Sky P Premium Motorized Skylight Side Channel Assembly (20)

Motorized Bottom-Up Shade For shades deployed from the bottom of the window Mariak Industries Inc. offers Bottom Up shades. Fabric rolled on the tube is placed inside of the aluminum enclosure in the bottom of the window. Cables pulling the hem bar are secured to the upper tube which contains the lifting AC motor. The upper tube is mounted on the brackets and concealed in an upper aluminum enclosure at the top of the window. Lifting cables are typically attached at the ends of the hem bar to provide clear view or they follow the mullions of the window per costumer specification. Optional snap-on side channels are also available for this product. Typically 4 ½ by 4 ½ L fascia are used as an enclosure. For larger skylights, enclosures measuring 5 ½ by 5 3/8 and 7 by 9 are also available. Please contact Mariak for a price quote. Bottom Shade in 5-1/2 Bottom Shade in 7 Motorized Bottom-Up Shade Head Box Head Box with Motor on Top Motorized Bottom-Up Shade with Motor and Fabric on the Bottom The Bottom-Up Shade that Mariak Industries Inc. offers can be configured with motor on the top or with both fabric and the motor on the bottom. The fabric on the tube is placed closer to the window while the motor winding cables is placed away from the window. Both the fabric and the motor tube are suspended from one 5 ½ by 7 3/8 bracket. Rectangular end caps cover both ends while the aluminum fascia covers the top. A pulley system guides the cable from the motor tube to the top of the window and down to the hem bar finishing the shade. Cables could be placed at the end of the shade or follow the mullions, per customer request. Please contact Mariak for a price quote. Motorized Bottom-Up with Rollers And brackets exposed Motorized Bottom-Up shade with Motor on the Bottom Roll: Available for reversed roll only Color: White Mount: Inside or Outside Motor: AC Control: Right or Left Minimum : 30 Maximum : 144 Minimum Length: 30 Maximum Length: 180 (21)

In-Stock Fabric Selection Fire Retardant Fabric Selection Number of Colors Stocked Roll Price Table EconoScreen 1% 7 98 or 118 2.2 EconoScreen 3% 7 98 or 118 2.1 EconoScreen 5% 7 98 or 118 2 Ferrari Soltis 99 3% 4 106 5 Matte Vinyl Blackout 11 72 1 Mermet E-Screen 5% 5 96 4 Mermet E-Screen 10% 5 96 4 Mermet M-Screen 3% 8 98 5 Mermet M-Screen 5% 8 98 4 Mermet M-Screen 5% Deco 4 98 5 Mermet Vela (PVC-Free) 3% 4 118 6 Phifer SheerWeave 2360 10% 9 98 4 Phifer SheerWeave 2390 5% 9 98, 126 * 4 Phifer SheerWeave 2410 3% 9 98, 126 * 5 Phifer SheerWeave 2500 1% 9 98 7 Phifer SheerWeave 2701 1% 5 98 7 Phifer SheerWeave 2703 3% 5 98 5 Phifer SheerWeave 2705 5% 5 98 4 Phifer SheerWeave 2710 10% 5 98 4 Phifer SheerWeave 3000 14% 5 96 3 Phifer SheerWeave 4000 5% 9 98, 126 * 4 Phifer SheerWeave 4100 10% 9 98 4 Phifer SheerWeave 4400 3% 9 98, 126 * 5 Phifer SheerWeave 4800 1% 12 96 7 Phifer SheerWeave 7000 Blackout 8 94 11 Phifer SheerWeave 7100 Blackout 6 72 9 Phifer SheerWeave 7500 Blackout 10 98 or 118 2.2 Phifer SheerWeave Infinity (PVC-Free) 3% 9 98 13 Phifer SheerWeave Infinity (PVC-Free) 5% 9 98 12 Phifer SheerWeave Performance Plus 2390 5% 10 96 14 Phifer SheerWeave Performance Plus 2410 3% 10 96 15 *Certain Phifer SheerWeave colors are available at 126 wide. Please consult Mariak Technical Support for more details. 126 Wide materials are in high demand and very difficult to source as a result of vendor production constraints. Thus, 126 wide materials will only be used upon request. Residential Fabric Selection Number of Colors Stocked Roll Price Table Cairo (PVC-Free) 3 78 4.1 Diamonds (PVC-Free) 4 120 8 Marblite (PVC-Free) 4 120 8 Milan (PVC-Free) 5 72 4.1 Noblette (PVC-Free) 4 110 10 SheerWeave 5000** 16 98 7.1 Suede Room Darkening 4 78 13 Vineyard (PVC-Free) 4 120 8 Whitney Light Filtering 5 78 1 Whitney Room Darkening 5 78 1.1 Woodland (PVC-Free) 5 72 4.1 Zute (PVC-Free) 2 72 4.1 All ** the Certain above Phifer listed SheerWeave fabrics are stocked 5000 colors by Mariak. pass some Upon Fire request, Retardant additional tests, but fabrics most from do not Alkenz, pass Ferrari, NFPA-701. Mermet, Please and consult Phifer the may Mariak be Contract product specification manual for more details. All the above listed fabrics are stocked by Mariak. Upon request, additional (22) fabrics from Alkenz, Ferrari, Mermet and Phifer may be ordered. All special order fabrics are priced based on contract quote. (22) 8-11-11

Length Sun Control Roller Shades Suggested Retail Price Table 1 Matte Vinyl Blackout 0% Open 72" Wide Fabric Fiberglass / PVC Whitney Light Filtering 78" Wide Fabric 100% Polyester Side 24 36 48 60 72 84 96 108 120 132 144 156 Channels 36 82 104 128 149 192 221 233 296 518 564 614 836 70 48 91 115 140 165 212 245 258 409 520 570 618 842 93 60 99 128 156 183 230 271 315 411 524 572 620 845 116 72 107 138 168 199 252 294 342 412 525 575 622 847 139 84 114 150 184 218 272 321 366 431 665 730 789 1038 162 96 139 179 219 257 294 349 395 614 671 739 798 1050 185 108 149 191 233 275 315 374 420 616 672 742 803 1055 208 120 165 206 248 292 336 399 446 618 677 747 808 1060 231 132 194 240 286 336 386 455 471 731 801 884 958 1231 254 144 201 251 300 353 407 481 497 732 807 888 962 1235 277 156 231 292 353 418 483 574 597 742 816 1000 1083 1253 300 Shades under dashed line will be railroaded and have a visible seam Fascia & Headbox Accessories Additional Options: 24 36 48 60 72 84 96 108 120 132 144 156 3" & 4" Square Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Round Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Fabric Wrapped Fascia 89 110 131 152 173 194 215 236 257 278 299 320 Shade Pocket (Without Lip) 132 169 206 243 280 319 355 391 428 465 502 539 Shade Pocket with Lip 132 169 206 243 280 319 355 391 428 465 502 539 Dual Shade Pocket (Without Lip) 210 289 368 447 526 605 684 763 842 921 1000 1079 Closure Plate for Pocket 17 24 31 38 45 50 58 66 73 80 87 94 Hanger with Closure Plate 21 33 45 57 69 81 93 105 117 129 141 153 Inserted Fabric Valance 24 30 36 42 48 54 60 66 72 78 84 90 Ceiling "L" Fascia 51 70 89 108 127 146 165 184 203 222 241 260 Sill Channel 24 35 46 57 68 79 90 101 112 123 134 145 Cassette Commercial w/fascia 100 140 180 220 260 300 340 380 420 N/A N/A N/A Cassette Retail w/fabric Insert 63 82 101 120 139 158 177 N/A N/A N/A N/A N/A Roller Shade Surcharge Options Stainless Steel Chain $12.00 White or Black Steel Chain $24.00 Platinum Clutch with Steel Chain $10.00 Net External Aluminum Hembar $10.00 Wrapped Hembar $15.00 Spring Assisted Clutch Shade $125.00 Exterior Shade Guide Wire System$120.00 Bottom-Up Shade with Clutch $275.00 Multiple Band Motorized Shades 1. Price each band separately and add together 2. Price each coupler surcharge and add together 3. Add shade band and coupler prices together Straight Line Coupler $100.00 90 o Corner Coupler $200.00 Important Items To Note: Screen fabrics will be fabricated vertically or horizontally (railroaded) at the factory's discretion. Any shades wider and longer than the fabric's width will have one or more visible seams (splices). The maximum warrantied size of a clutch operated shade is 126" x 144". Large Clutch shades may require a spring assisted lifting mechanism. Please note the Clutch Fabrication Chart on page 39 for specific size requirements. Side channel surcharge includes left & right channels. Seal brushes available upon request. Prices for valances, boxes, and pockets include all brackets and end caps. Reverse roll option is not available for square, round, or wrapped fabric fascias. The size of a shade will determine the size of the tube used; upgrades to larger tubes will be available upon request. Please review the clutch fabrication chart on page 39 & 40. Shades exceeding a 3-to-1 ratio may have problems tracking. In other words, shades with a height dimension that is more than 3 times the width measurement may be susceptible to telescoping. All measurements must be bracket to bracket. Shades up to 92" in width shipped via FedEx: $ 4.00 / unit Net Freight Charge Shades 92 1/8" to 125" in width shipped via FedEx: $ 75.00 / unit Net Freight Charge Shades 125 1/8" or greater in width shipped via Common Carrier: $ 150.00 per shipment 8-11-11 kb (23)

Length Sun Control Roller Shades Suggested Retail Price Table 1.1 Whitney Room Darkening 78" Wide Fabric 100% Polyester Side 24 36 48 60 72 84 96 108 120 132 144 156 Channels 36 99 125 154 179 231 266 280 356 622 677 737 1004 70 48 110 139 169 199 255 295 310 491 625 685 742 1011 93 60 119 154 188 220 276 326 379 494 629 687 745 1015 116 72 129 166 202 239 303 354 411 495 630 691 747 1017 139 84 137 180 221 262 327 386 440 518 799 877 947 1246 162 96 167 215 263 309 353 419 475 737 806 887 958 1261 185 108 179 230 280 331 379 449 505 740 807 891 964 1267 208 120 199 248 298 351 404 479 536 742 813 897 970 1273 231 132 233 289 344 404 464 547 566 878 962 1061 1150 1478 254 144 242 302 361 424 489 578 597 879 969 1066 1155 1483 277 156 278 351 424 502 580 689 717 891 980 1201 1300 1504 300 Shades under dashed line will be railroaded and have a visible seam Fascia & Headbox Accessories Additional Options: 24 36 48 60 72 84 96 108 120 132 144 156 3" & 4" Square Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Round Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Fabric Wrapped Fascia 89 110 131 152 173 194 215 236 257 278 299 320 Shade Pocket (Without Lip) 132 169 206 243 280 319 355 391 428 465 502 539 Shade Pocket with Lip 132 169 206 243 280 319 355 391 428 465 502 539 Dual Shade Pocket (Without Lip) 210 289 368 447 526 605 684 763 842 921 1000 1079 Closure Plate for Pocket 17 24 31 38 45 50 58 66 73 80 87 94 Hanger with Closure Plate 21 33 45 57 69 81 93 105 117 129 141 153 Inserted Fabric Valance 24 30 36 42 48 54 60 66 72 78 84 90 Ceiling "L" Fascia 51 70 89 108 127 146 165 184 203 222 241 260 Sill Channel 24 35 46 57 68 79 90 101 112 123 134 145 Cassette Commercial w/fascia 100 140 180 220 260 300 340 380 420 N/A N/A N/A Cassette Retail w/fabric Insert 63 82 101 120 139 158 177 N/A N/A N/A N/A N/A Roller Shade Surcharge Options Stainless Steel Chain $12.00 White or Black Steel Chain $24.00 Platinum Clutch with Steel Chain $10.00 Net External Aluminum Hembar $10.00 Wrapped Hembar $15.00 Spring Assisted Clutch Shade $125.00 Exterior Shade Guide Wire System$120.00 Bottom-Up Shade with Clutch $275.00 Multiple Band Motorized Shades 1. Price each band separately and add together 2. Price each coupler surcharge and add together 3. Add shade band and coupler prices together Straight Line Coupler $100.00 90 o Corner Coupler $200.00 Important Items To Note: Screen fabrics will be fabricated vertically or horizontally (railroaded) at the factory's discretion. Any shades wider and longer than the fabric's width will have one or more visible seams (splices). The maximum warrantied size of a clutch operated shade is 126" x 144". Large Clutch shades may require a spring assisted lifting mechanism. Please note the Clutch Fabrication Chart on page 39 for specific size requirements. Side channel surcharge includes left & right channels. Seal brushes available upon request. Prices for valances, boxes, and pockets include all brackets and end caps. Reverse roll option is not available for square, round, or wrapped fabric fascias. The size of a shade will determine the size of the tube used; upgrades to larger tubes will be available upon request. Please review the clutch fabrication chart on page 39 & 40. Shades exceeding a 3-to-1 ratio may have problems tracking. In other words, shades with a height dimension that is more than 3 times the width measurement may be susceptible to telescoping. All measurements must be bracket to bracket. Shades up to 92" in width shipped via FedEx: $ 4.00 / unit Net Freight Charge Shades 92 1/8" to 125" in width shipped via FedEx: $ 75.00 / unit Net Freight Charge Shades 125 1/8" or greater in width shipped via Common Carrier: $ 150.00 per shipment 8-11-11 kb (24)

Length Suggested Retail Price Table 2 EconoScreen Sun Control Roller Shades 5% Open 98" or 118" Wide Fabric Polyester / PVC Side 24 36 48 60 72 84 96 108 120 132 144 156 Channels 36 89 113 138 160 205 238 250 319 557 606 659 898 70 48 97 124 152 178 228 264 278 440 559 612 663 903 93 60 108 138 168 197 248 291 340 441 563 614 666 907 116 72 116 149 181 215 271 318 368 444 565 617 668 909 139 84 123 161 198 235 292 345 393 464 714 784 848 1115 162 96 151 193 236 276 318 375 425 659 721 793 858 1128 185 108 160 205 250 296 339 402 452 662 722 796 861 1132 208 120 178 222 266 313 362 429 478 664 726 802 868 1138 231 132 207 259 307 362 414 489 506 785 860 950 1028 1321 254 144 217 270 323 380 437 517 535 787 867 954 1033 1326 277 156 248 313 380 450 518 616 642 796 877 1074 1163 1346 300 Shades under dashed line will be railroaded and have a visible seam Fascia & Headbox Accessories Additional Options: 24 36 48 60 72 84 96 108 120 132 144 156 3" & 4" Square Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Round Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Fabric Wrapped Fascia 89 110 131 152 173 194 215 236 257 278 299 320 Shade Pocket (Without Lip) 132 169 206 243 280 319 355 391 428 465 502 539 Shade Pocket with Lip 132 169 206 243 280 319 355 391 428 465 502 539 Dual Shade Pocket (Without Lip) 210 289 368 447 526 605 684 763 842 921 1000 1079 Closure Plate for Pocket 17 24 31 38 45 50 58 66 73 80 87 94 Hanger with Closure Plate 21 33 45 57 69 81 93 105 117 129 141 153 Inserted Fabric Valance 24 30 36 42 48 54 60 66 72 78 84 90 Ceiling "L" Fascia 51 70 89 108 127 146 165 184 203 222 241 260 Sill Channel 24 35 46 57 68 79 90 101 112 123 134 145 Cassette Commercial w/fascia 100 140 180 220 260 300 340 380 420 N/A N/A N/A Cassette Retail w/fabric Insert 63 82 101 120 139 158 177 N/A N/A N/A N/A N/A Roller Shade Surcharge Options Stainless Steel Chain $12.00 White or Black Steel Chain $24.00 Platinum Clutch with Steel Chain $10.00 Net External Aluminum Hembar $10.00 Wrapped Hembar $15.00 Spring Assisted Clutch Shade $125.00 Exterior Shade Guide Wire System $120.00 Bottom-Up Shade with Clutch $275.00 Multiple Band Motorized Shades 1. Price each band separately and add together 2. Price each coupler surcharge and add together 3. Add shade band and coupler prices together Straight Line Coupler $100.00 90 o Corner Coupler $200.00 Important Items To Note: Screen fabrics will be fabricated vertically or horizontally (railroaded) at the factory's discretion. Any shades wider and longer than the fabric's width will have one or more visible seams (splices). The maximum warrantied size of a clutch operated shade is 126" x 144". Large Clutch shades may require a spring assisted lifting mechanism. Please note the Clutch Fabrication Chart on page 39 for specific size requirements. Side channel surcharge includes left & right channels. Seal brushes available upon request. Prices for valances, boxes, and pockets include all brackets and end caps. Reverse roll option is not available for square, round, or wrapped fabric fascias. The size of a shade will determine the size of the tube used; upgrades to larger tubes will be available upon request. Please review the clutch fabrication chart on page 39 & 40. Shades exceeding a 3-to-1 ratio may have problems tracking. In other words, shades with a height dimension that is more than 3 times the width measurement may be susceptible to telescoping. All measurements must be bracket to bracket. Shades up to 92" in width shipped via FedEx: $ 4.00 / unit Net Freight Charge Shades 92 1/8" to 125" in width shipped via FedEx: $ 75.00 / unit Net Freight Charge Shades 125 1/8" or greater in width shipped via Common Carrier: $ 150.00 per shipment 8-11-11 kb (25)

Length Suggested Retail Price Table 2.1 EconoScreen Sun Control Roller Shades 3% Open 98" or 118" Wide Fabric Polyester / PVC Side 24 36 48 60 72 84 96 108 120 132 144 156 Channels 36 100 127 155 180 230 267 280 358 624 679 739 1006 70 48 109 139 171 200 256 296 312 493 627 686 743 1075 93 60 121 155 189 221 278 326 381 494 631 688 746 1016 116 72 130 167 203 241 304 357 413 498 633 692 749 1019 139 84 138 181 222 264 328 387 441 520 800 879 950 1249 162 96 170 217 265 310 357 420 476 739 808 889 961 1264 185 108 180 230 280 332 380 451 507 742 809 892 965 1268 208 120 200 249 298 351 406 481 536 744 814 899 973 1275 231 132 232 291 344 406 464 548 567 880 964 1064 1152 1480 254 144 244 303 362 426 490 580 600 882 972 1069 1157 1486 277 156 278 351 426 504 581 690 720 892 983 1203 1303 1508 300 Shades under dashed line will be railroaded and have a visible seam Fascia & Headbox Accessories Additional Options: 24 36 48 60 72 84 96 108 120 132 144 156 3" & 4" Square Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Round Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Fabric Wrapped Fascia 89 110 131 152 173 194 215 236 257 278 299 320 Shade Pocket (Without Lip) 132 169 206 243 280 319 355 391 428 465 502 539 Shade Pocket with Lip 132 169 206 243 280 319 355 391 428 465 502 539 Dual Shade Pocket (Without Lip) 210 289 368 447 526 605 684 763 842 921 1000 1079 Closure Plate for Pocket 17 24 31 38 45 50 58 66 73 80 87 94 Hanger with Closure Plate 21 33 45 57 69 81 93 105 117 129 141 153 Inserted Fabric Valance 24 30 36 42 48 54 60 66 72 78 84 90 Ceiling "L" Fascia 51 70 89 108 127 146 165 184 203 222 241 260 Sill Channel 24 35 46 57 68 79 90 101 112 123 134 145 Cassette Commercial w/fascia 100 140 180 220 260 300 340 380 420 N/A N/A N/A Cassette Retail w/fabric Insert 63 82 101 120 139 158 177 N/A N/A N/A N/A N/A Roller Shade Surcharge Options Stainless Steel Chain $12.00 White or Black Steel Chain $24.00 Platinum Clutch with Steel Chain $10.00 Net External Aluminum Hembar $10.00 Wrapped Hembar $15.00 Spring Assisted Clutch Shade $125.00 Exterior Shade Guide Wire System $120.00 Bottom-Up Shade with Clutch $275.00 Multiple Band Motorized Shades 1. Price each band separately and add together 2. Price each coupler surcharge and add together 3. Add shade band and coupler prices together Straight Line Coupler $100.00 90 o Corner Coupler $200.00 Important Items To Note: Screen fabrics will be fabricated vertically or horizontally (railroaded) at the factory's discretion. Any shades wider and longer than the fabric's width will have one or more visible seams (splices). The maximum warrantied size of a clutch operated shade is 126" x 144". Large Clutch shades may require a spring assisted lifting mechanism. Please note the Clutch Fabrication Chart on page 39 for specific size requirements. Side channel surcharge includes left & right channels. Seal brushes available upon request. Prices for valances, boxes, and pockets include all brackets and end caps. Reverse roll option is not available for square, round, or wrapped fabric fascias. The size of a shade will determine the size of the tube used; upgrades to larger tubes will be available upon request. Please review the clutch fabrication chart on page 39 & 40. Shades exceeding a 3-to-1 ratio may have problems tracking. In other words, shades with a height dimension that is more than 3 times the width measurement may be susceptible to telescoping. All measurements must be bracket to bracket. Shades up to 92" in width shipped via FedEx: $ 4.00 / unit Net Freight Charge Shades 92 1/8" to 125" in width shipped via FedEx: $ 75.00 / unit Net Freight Charge Shades 125 1/8" or greater in width shipped via Common Carrier: $ 150.00 per shipment 8-11-11 kb (26)

Length Suggested Retail Price Table 2.2 Sun Control Roller Shades EconoScreen 1% Open 98" or 118" Wide Fabric Polyester / PVC SheerWeave 7500 0% Open 98" or 118" Wide Fabric Fiberglass / PVC Side 24 36 48 60 72 84 96 108 120 132 144 156 Channels 36 106 134 189 242 281 295 377 658 716 716 778 1060 70 48 115 147 180 211 270 312 329 520 660 723 783 1066 93 60 128 163 199 233 293 344 402 521 665 725 786 1071 116 72 137 176 214 254 320 376 435 524 667 729 789 1073 139 84 146 190 234 278 345 408 464 548 843 926 1001 1316 162 96 179 228 279 326 376 443 502 778 851 936 1013 1332 185 108 189 242 295 350 401 475 534 782 852 940 1016 1336 208 120 211 262 314 370 428 507 565 784 857 947 1025 1343 231 132 245 306 363 428 489 578 598 927 1015 1121 1214 1559 254 144 257 319 382 449 516 611 632 929 1024 1126 1219 1565 277 156 293 370 449 531 612 727 758 940 1035 1268 1373 1589 300 Shades under dashed line will be railroaded and have a visible seam Fascia & Headbox Accessories Additional Options: 24 36 48 60 72 84 96 108 120 132 144 156 3" & 4" Square Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Round Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Fabric Wrapped Fascia 89 110 131 152 173 194 215 236 257 278 299 320 Shade Pocket (Without Lip) 132 169 206 243 280 319 355 391 428 465 502 539 Shade Pocket with Lip 132 169 206 243 280 319 355 391 428 465 502 539 Dual Shade Pocket (Without Lip) 210 289 368 447 526 605 684 763 842 921 1000 1079 Closure Plate for Pocket 17 24 31 38 45 50 58 66 73 80 87 94 Hanger with Closure Plate 21 33 45 57 69 81 93 105 117 129 141 153 Inserted Fabric Valance 24 30 36 42 48 54 60 66 72 78 84 90 Ceiling "L" Fascia 51 70 89 108 127 146 165 184 203 222 241 260 Sill Channel 24 35 46 57 68 79 90 101 112 123 134 145 Cassette Commercial w/fascia 100 140 180 220 260 300 340 380 420 N/A N/A N/A Cassette Retail w/fabric Insert 63 82 101 120 139 158 177 N/A N/A N/A N/A N/A Roller Shade Surcharge Options Stainless Steel Chain $12.00 White or Black Steel Chain $24.00 Platinum Clutch with Steel Chain $10.00 Net External Aluminum Hembar $10.00 Wrapped Hembar $15.00 Spring Assisted Clutch Shade $125.00 Exterior Shade Guide Wire System $120.00 Bottom-Up Shade with Clutch $275.00 Multiple Band Motorized Shades 1. Price each band separately and add together 2. Price each coupler surcharge and add together 3. Add shade band and coupler prices together Straight Line Coupler $100.00 90 o Corner Coupler $200.00 Important Items To Note: Screen fabrics will be fabricated vertically or horizontally (railroaded) at the factory's discretion. Any shades wider and longer than the fabric's width will have one or more visible seams (splices). The maximum warrantied size of a clutch operated shade is 126" x 144". Large Clutch shades may require a spring assisted lifting mechanism. Please note the Clutch Fabrication Chart on page 39 for specific size requirements. Side channel surcharge includes left & right channels. Seal brushes available upon request. Prices for valances, boxes, and pockets include all brackets and end caps. Reverse roll option is not available for square, round, or wrapped fabric fascias. The size of a shade will determine the size of the tube used; upgrades to larger tubes will be available upon request. Please review the clutch fabrication chart on page 39 & 40. Shades exceeding a 3-to-1 ratio may have problems tracking. In other words, shades with a height dimension that is more than 3 times the width measurement may be susceptible to telescoping. All measurements must be bracket to bracket. Shades up to 92" in width shipped via FedEx: $ 4.00 / unit Net Freight Charge Shades 92 1/8" to 125" in width shipped via FedEx: $ 75.00 / unit Net Freight Charge Shades 125 1/8" or greater in width shipped via Common Carrier: $ 150.00 per shipment 8-11-11 kb (27)

Length Suggested Retail Price Table 3 Sun Control Roller Shades SheerWeave 3000 14% Open 98" Wide Fabric Fiberglass / Polyester / PVC Side 24 36 48 60 72 84 96 108 120 132 144 156 Channels 36 95 120 147 172 221 256 269 342 599 653 709 968 70 48 104 133 162 192 245 284 299 473 601 659 713 973 93 60 115 147 181 212 266 313 365 475 606 661 717 976 116 72 123 159 195 230 291 341 395 477 608 664 720 979 139 84 132 173 213 251 314 371 424 498 769 844 912 1201 162 96 161 207 252 297 341 404 456 709 776 854 923 1215 185 108 172 221 269 318 364 432 487 712 777 857 928 1220 208 120 192 238 286 338 389 461 515 714 782 864 934 1226 231 132 223 278 330 389 446 527 544 845 926 1022 1108 1423 254 144 233 290 347 408 470 557 575 847 933 1026 1112 1427 277 156 267 338 408 483 558 663 690 857 944 1155 1252 1449 300 Shades under dashed line will be railroaded and have a visible seam Fascia & Headbox Accessories Additional Options: 24 36 48 60 72 84 96 108 120 132 144 156 3" & 4" Square Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Round Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Fabric Wrapped Fascia 89 110 131 152 173 194 215 236 257 278 299 320 Shade Pocket (Without Lip) 132 169 206 243 280 319 355 391 428 465 502 539 Shade Pocket with Lip 132 169 206 243 280 319 355 391 428 465 502 539 Dual Shade Pocket (Without Lip) 210 289 368 447 526 605 684 763 842 921 1000 1079 Closure Plate for Pocket 17 24 31 38 45 50 58 66 73 80 87 94 Hanger with Closure Plate 21 33 45 57 69 81 93 105 117 129 141 153 Inserted Fabric Valance 24 30 36 42 48 54 60 66 72 78 84 90 Ceiling "L" Fascia 51 70 89 108 127 146 165 184 203 222 241 260 Sill Channel 24 35 46 57 68 79 90 101 112 123 134 145 Cassette Commercial w/fascia 100 140 180 220 260 300 340 380 420 N/A N/A N/A Cassette Retail w/fabric Insert 63 82 101 120 139 158 177 N/A N/A N/A N/A N/A Roller Shade Surcharge Options Stainless Steel Chain $12.00 White or Black Steel Chain $24.00 Platinum Clutch with Steel Chain $10.00 Net External Aluminum Hembar $10.00 Wrapped Hembar $15.00 Spring Assisted Clutch Shade $125.00 Exterior Shade Guide Wire System $120.00 Bottom-Up Shade with Clutch $275.00 Multiple Band Motorized Shades 1. Price each band separately and add together 2. Price each coupler surcharge and add together 3. Add shade band and coupler prices together Straight Line Coupler $100.00 90 o Corner Coupler $200.00 Important Items To Note: Screen fabrics will be fabricated vertically or horizontally (railroaded) at the factory's discretion. Any shades wider and longer than the fabric's width will have one or more visible seams (splices). The maximum warrantied size of a clutch operated shade is 126" x 144". Large Clutch shades may require a spring assisted lifting mechanism. Please note the Clutch Fabrication Chart on page 39 for specific size requirements. Side channel surcharge includes left & right channels. Seal brushes available upon request. Prices for valances, boxes, and pockets include all brackets and end caps. Reverse roll option is not available for square, round, or wrapped fabric fascias. The size of a shade will determine the size of the tube used; upgrades to larger tubes will be available upon request. Please review the clutch fabrication chart on page 39 & 40. Shades exceeding a 3-to-1 ratio may have problems tracking. In other words, shades with a height dimension that is more than 3 times the width measurement may be susceptible to telescoping. All measurements must be bracket to bracket. Shades up to 92" in width shipped via FedEx: $ 4.00 / unit Net Freight Charge Shades 92 1/8" to 125" in width shipped via FedEx: $ 75.00 / unit Net Freight Charge Shades 125 1/8" or greater in width shipped via Common Carrier: $ 150.00 per shipment 8-11-11 kb (28)

Length Suggested Retail Price Table 4 SheerWeave 2360 10% Open 98" Wide Fabric Fiberglass / PVC SheerWeave 2390 5% Open 98" Wide Fabric Fiberglass / PVC SheerWeave 2705 5% Open 98" Wide Fabric Fiberglass / PVC SheerWeave 2710 10% Open 98" Wide Fabric Fiberglass / PVC SheerWeave 4000 5% Open 98" Wide Fabric Polyester / PVC SheerWeave 4100 10% Open 98" Wide Fabric Polyester / PVC E-Screen 7505 5% Open 96" Wide Fabric Fiberglass / PVC M-Screen 8505 5% Open 98" Wide Fabric Fiberglass / PVC Side 24 36 48 60 72 84 96 108 120 132 144 156 Channels 36 103 132 161 187 242 279 293 373 655 712 774 1057 70 48 115 145 177 208 267 309 326 516 657 719 780 1063 93 60 125 161 197 231 290 343 398 518 662 722 783 1066 116 72 135 174 214 251 319 372 432 520 664 725 786 1069 139 84 144 188 233 275 344 405 462 544 839 921 996 1311 162 96 176 226 276 324 372 441 498 774 848 932 1008 1327 185 108 187 241 293 347 397 472 532 777 850 936 1013 1332 208 120 208 260 312 369 426 503 562 781 854 942 1020 1338 231 132 244 303 361 425 487 575 595 922 1011 1116 1210 1553 254 144 254 318 378 446 513 607 627 924 1018 1121 1214 1559 277 156 291 369 446 529 609 724 754 936 1031 1263 1368 1583 300 Shades under dashed line will be railroaded and have a visible seam Additional Options: 24 36 48 60 72 84 96 108 120 132 144 156 3" & 4" Square Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Round Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Fabric Wrapped Fascia 89 110 131 152 173 194 215 236 257 278 299 320 Shade Pocket (Without Lip) 132 169 206 243 280 319 355 391 428 465 502 539 Shade Pocket with Lip 132 169 206 243 280 319 355 391 428 465 502 539 Dual Shade Pocket (Without Lip) 210 289 368 447 526 605 684 763 842 921 1000 1079 Closure Plate for Pocket 17 24 31 38 45 50 58 66 73 80 87 94 Hanger with Closure Plate 21 33 45 57 69 81 93 105 117 129 141 153 Inserted Fabric Valance 24 30 36 42 48 54 60 66 72 78 84 90 Ceiling "L" Fascia 51 70 89 108 127 146 165 184 203 222 241 260 Sill Channel 24 35 46 57 68 79 90 101 112 123 134 145 Cassette Commercial w/fascia 100 140 180 220 260 300 340 380 420 N/A N/A N/A Cassette Retail w/fabric Insert 63 82 101 120 139 158 177 N/A N/A N/A N/A N/A Roller Shade Surcharge Options Stainless Steel Chain $12.00 White or Black Steel Chain $24.00 Platinum Clutch with Steel Chain $10.00 Net External Aluminum Hembar $10.00 Wrapped Hembar $15.00 Spring Assisted Clutch Shade $125.00 Exterior Shade Guide Wire System $120.00 Bottom-Up Shade with Clutch $275.00 Multiple Band Motorized Shades 1. Price each band separately and add together 2. Price each coupler surcharge and add together 3. Add shade band and coupler prices together Straight Line Coupler $100.00 90 o Corner Coupler $200.00 Sun Control Roller Shades Fascia & Headbox Accessories Important Items To Note: Screen fabrics will be fabricated vertically or horizontally (railroaded) at the factory's discretion. Any shades wider and longer than the fabric's width will have one or more visible seams (splices). The maximum warrantied size of a clutch operated shade is 126" x 144". Large Clutch shades may require a spring assisted lifting mechanism. Please note the Clutch Fabrication Chart on page 39 for specific size requirements. Side channel surcharge includes left & right channels. Seal brushes available upon request. Prices for valances, boxes, and pockets include all brackets and end caps. Reverse roll option is not available for square, round, or wrapped fabric fascias. The size of a shade will determine the size of the tube used; upgrades to larger tubes will be available upon request. Please review the clutch fabrication chart on page 39 & 40. Shades exceeding a 3-to-1 ratio may have problems tracking. In other words, shades with a height dimension that is more than 3 times the width measurement may be susceptible to telescoping. All measurements must be bracket to bracket. Shades up to 92" in width shipped via FedEx: $ 4.00 / unit Net Freight Charge Shades 92 1/8" to 125" in width shipped via FedEx: $ 75.00 / unit Net Freight Charge Shades 125 1/8" or greater in width shipped via Common Carrier: $ 150.00 per shipment (29) 8-11-11 kb

Length Sun Control Roller Shades Suggested Retail Price Table 4.1 - Decorative Fabrics Cairo (PVC-Free) Light Filtering 72" Wide Fabric Polyester Milan (PVC-Free) Light Filtering 72" Wide Fabric Polyester Woodland (PVC-Free) Light Filtering 72" Wide Fabric Polyester Zute (PVC-Free) Light Filtering 72" Wide Fabric Polyester Side 24 36 48 60 72 84 96 108 120 132 144 156 Channels 36 103 132 161 187 242 70 48 115 145 177 208 267 93 60 125 161 197 231 290 116 72 135 174 214 251 319 This fabric has a distinctive pattern 139 84 144 188 233 275 344 and should not be railroaded. 162 96 176 226 276 324 372 185 108 187 241 293 347 397 The maximum width of a shade using 208 120 208 260 312 369 426 the above listed fabrics is 72". 231 132 244 303 361 425 487 254 144 254 318 378 446 513 277 156 291 369 446 529 609 300 Additional Options: 24 36 48 60 72 84 96 108 120 132 144 156 3" & 4" Square Aluminum Fascia 45 55 65 75 85 3" & 4" Round Aluminum Fascia 45 55 65 75 85 3" & 4" Fabric Wrapped Fascia 89 110 131 152 173 Shade Pocket (Without Lip) 132 169 206 243 280 Shade Pocket with Lip 132 169 206 243 280 Dual Shade Pocket (Without Lip) 210 289 368 447 526 Closure Plate for Pocket 17 24 31 38 45 Hanger with Closure Plate 21 33 45 57 69 Inserted Fabric Valance 24 30 36 42 48 Ceiling "L" Fascia 51 70 89 108 127 Sill Channel 24 35 46 57 68 Cassette Commercial w/fascia 100 140 180 220 260 Cassette Retail w/fabric Insert 63 82 101 120 139 Fascia & Headbox Accessories This fabric has a distinctive pattern and should not be railroaded. The maximum width of a shade using the above listed fabrics is 72". Roller Shade Surcharge Options Stainless Steel Chain $12.00 White or Black Steel Chain $24.00 Platinum Clutch with Steel Chain $10.00 Net External Aluminum Hembar $10.00 Wrapped Hembar $15.00 Spring Assisted Clutch Shade $125.00 Exterior Shade Guide Wire System $120.00 Bottom-Up Shade with Clutch $275.00 Multiple Band Motorized Shades 1. Price each band separately and add together 2. Price each coupler surcharge and add together 3. Add shade band and coupler prices together Straight Line Coupler $100.00 90 o Corner Coupler $200.00 Important Items To Note: Screen fabrics will be fabricated vertically or horizontally (railroaded) at the factory's discretion. Any shades wider and longer than the fabric's width will have one or more visible seams (splices). The maximum warrantied size of a clutch operated shade is 126" x 144". Large Clutch shades may require a spring assisted lifting mechanism. Please note the Clutch Fabrication Chart on page 39 for specific size requirements. Side channel surcharge includes left & right channels. Seal brushes available upon request. Prices for valances, boxes, and pockets include all brackets and end caps. Reverse roll option is not available for square, round, or wrapped fabric fascias. The size of a shade will determine the size of the tube used; upgrades to larger tubes will be available upon request. Please review the clutch fabrication chart on page 39 & 40. Shades exceeding a 3-to-1 ratio may have problems tracking. In other words, shades with a height dimension that is more than 3 times the width measurement may be susceptible to telescoping. All measurements must be bracket to bracket. Shades up to 92" in width shipped via FedEx: $ 4.00 / unit Net Freight Charge Shades 92 1/8" to 125" in width shipped via FedEx: $ 75.00 / unit Net Freight Charge Shades 125 1/8" or greater in width shipped via Common Carrier: $ 150.00 per shipment (30) 8-11-11 kb

Length Suggested Retail Price Table 5 Sun Control Roller Shades SheerWeave 2410 3% Open 98" Wide Fabric Fiberglass / PVC SheerWeave 2703 3% Open 98" Wide Fabric Fiberglass / PVC SheerWeave 4400 3% Open 98" Wide Fabric Polyester / PVC Ferrari Soltis 99 3% Open 106" Wide Fabric Polyester / PVC M-Screen 8503 3% Open 98" Wide Fabric Fiberglass / PVC M-Screen 8505 Deco 3% Open 98" Wide Fabric Fiberglass / PVC Side 24 36 48 60 72 84 96 108 120 132 144 156 Channels 36 110 138 170 198 255 293 309 393 689 750 815 1112 70 48 120 153 186 220 282 326 343 544 691 758 821 1119 93 60 132 170 207 243 306 361 419 546 697 761 825 1123 116 72 142 183 224 265 335 392 454 549 699 764 828 1126 139 84 152 199 244 289 362 427 487 573 885 971 1048 1380 162 96 185 238 290 341 392 465 524 815 892 982 1062 1397 185 108 198 254 309 365 418 497 559 818 895 986 1066 1403 208 120 220 273 329 389 448 531 592 822 899 993 1075 1410 231 132 257 320 380 447 513 605 626 972 1064 1175 1274 1636 254 144 267 334 398 469 540 640 661 974 1073 1181 1279 1642 277 156 307 389 469 556 642 763 794 986 1085 1329 1440 1667 300 Shades under dashed line will be railroaded and have a visible seam Fascia & Headbox Accessories Additional Options: 24 36 48 60 72 84 96 108 120 132 144 156 3" & 4" Square Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Round Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Fabric Wrapped Fascia 89 110 131 152 173 194 215 236 257 278 299 320 Shade Pocket (Without Lip) 132 169 206 243 280 319 355 391 428 465 502 539 Shade Pocket with Lip 132 169 206 243 280 319 355 391 428 465 502 539 Dual Shade Pocket (Without Lip) 210 289 368 447 526 605 684 763 842 921 1000 1079 Closure Plate for Pocket 17 24 31 38 45 50 58 66 73 80 87 94 Hanger with Closure Plate 21 33 45 57 69 81 93 105 117 129 141 153 Inserted Fabric Valance 24 30 36 42 48 54 60 66 72 78 84 90 Ceiling "L" Fascia 51 70 89 108 127 146 165 184 203 222 241 260 Sill Channel 24 35 46 57 68 79 90 101 112 123 134 145 Cassette Commercial w/fascia 100 140 180 220 260 300 340 380 420 N/A N/A N/A Cassette Retail w/fabric Insert 63 82 101 120 139 158 177 N/A N/A N/A N/A N/A Roller Shade Surcharge Options Stainless Steel Chain $12.00 White or Black Steel Chain $24.00 Platinum Clutch with Steel Chain $10.00 Net External Aluminum Hembar $10.00 Wrapped Hembar $15.00 Spring Assisted Clutch Shade $125.00 Exterior Shade Guide Wire System $120.00 Bottom-Up Shade with Clutch $275.00 Multiple Band Motorized Shades 1. Price each band separately and add together 2. Price each coupler surcharge and add together 3. Add shade band and coupler prices together Straight Line Coupler $100.00 90 o Corner Coupler $200.00 Important Items To Note: Screen fabrics will be fabricated vertically or horizontally (railroaded) at the factory's discretion. Any shades wider and longer than the fabric's width will have one or more visible seams (splices). The maximum warrantied size of a clutch operated shade is 126" x 144". Large Clutch shades may require a spring assisted lifting mechanism. Please note the Clutch Fabrication Chart on page 39 for specific size requirements. Side channel surcharge includes left & right channels. Seal brushes available upon request. Prices for valances, boxes, and pockets include all brackets and end caps. Reverse roll option is not available for square, round, or wrapped fabric fascias. The size of a shade will determine the size of the tube used; upgrades to larger tubes will be available upon request. Please review the clutch fabrication chart on page 39 & 40. Shades exceeding a 3-to-1 ratio may have problems tracking. In other words, shades with a height dimension that is more than 3 times the width measurement may be susceptible to telescoping. All measurements must be bracket to bracket. Shades up to 92" in width shipped via FedEx: $ 4.00 / unit Net Freight Charge Shades 92 1/8" to 125" in width shipped via FedEx: $ 75.00 / unit Net Freight Charge Shades 125 1/8" or greater in width shipped via Common Carrier: $ 150.00 per shipment (31) 8-11-11 kb

Length Suggested Retail Price Table 6 Sun Control Roller Shades Vela (PVC-Free) 3% Open 118" Wide Fabric Polyester Side 24 36 48 60 72 84 96 108 118 132 144 156 Channels 36 114 144 177 206 266 307 323 340 357 70 48 125 160 195 229 293 341 357 376 396 This fabric has a 93 60 137 177 217 255 320 376 438 461 486 distinctive pattern 116 72 147 192 235 277 350 409 475 500 527 and should not be 139 84 158 207 256 302 377 446 509 535 563 railroaded. 162 96 194 248 303 355 409 486 549 577 607 185 108 206 265 323 382 437 519 584 615 647 The maximum 208 120 229 286 344 406 468 554 618 650 685 width of a shade 231 132 268 333 396 467 535 633 655 689 725 using the above 254 144 279 349 416 490 564 668 690 727 765 listed fabrics is 118". 277 156 321 406 490 581 670 796 829 873 918 300 Fascia & Headbox Accessories Additional Options: 24 36 48 60 72 84 96 108 120 132 144 156 3" & 4" Square Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Round Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Fabric Wrapped Fascia 89 110 131 152 173 194 215 236 257 278 299 320 Shade Pocket (Without Lip) 132 169 206 243 280 319 355 391 428 465 502 539 Shade Pocket with Lip 132 169 206 243 280 319 355 391 428 465 502 539 Dual Shade Pocket (Without Lip) 210 289 368 447 526 605 684 763 842 921 1000 1079 Closure Plate for Pocket 17 24 31 38 45 50 58 66 73 80 87 94 Hanger with Closure Plate 21 33 45 57 69 81 93 105 117 129 141 153 Inserted Fabric Valance 24 30 36 42 48 54 60 66 72 78 84 90 Ceiling "L" Fascia 51 70 89 108 127 146 165 184 203 222 241 260 Sill Channel 24 35 46 57 68 79 90 101 112 123 134 145 Cassette Commercial w/fascia 100 140 180 220 260 300 340 380 420 N/A N/A N/A Cassette Retail w/fabric Insert 63 82 101 120 139 158 177 N/A N/A N/A N/A N/A Roller Shade Surcharge Options Stainless Steel Chain $12.00 White or Black Steel Chain $24.00 Platinum Clutch with Steel Chain $10.00 Net External Aluminum Hembar $10.00 Wrapped Hembar $15.00 Spring Assisted Clutch Shade $125.00 Exterior Shade Guide Wire System $120.00 Bottom-Up Shade with Clutch $275.00 Multiple Band Motorized Shades 1. Price each band separately and add together 2. Price each coupler surcharge and add together 3. Add shade band and coupler prices together Straight Line Coupler $100.00 90 o Corner Coupler $200.00 Important Items To Note: Screen fabrics will be fabricated vertically or horizontally (railroaded) at the factory's discretion. Any shades wider and longer than the fabric's width will have one or more visible seams (splices). The maximum warrantied size of a clutch operated shade is 126" x 144". Large Clutch shades may require a spring assisted lifting mechanism. Please note the Clutch Fabrication Chart on page 39 for specific size requirements. Side channel surcharge includes left & right channels. Seal brushes available upon request. Prices for valances, boxes, and pockets include all brackets and end caps. Reverse roll option is not available for square, round, or wrapped fabric fascias. The size of a shade will determine the size of the tube used; upgrades to larger tubes will be available upon request. Please review the clutch fabrication chart on page 39 & 40 Shades exceeding a 3-to-1 ratio may have problems tracking. In other words, shades with a height dimension that is more than 3 times the width measurement may be susceptible to telescoping. All measurements must be bracket to bracket. Shades up to 92" in width shipped via FedEx: $ 4.00 / unit Net Freight Charge Shades 92 1/8" to 125" in width shipped via FedEx: $ 75.00 / unit Net Freight Charge Shades 125 1/8" or greater in width shipped via Common Carrier: $ 150.00 per shipment 8-11-11 kb (32)

Length Suggested Retail Price Table 7 Sun Control Roller Shades SheerWeave 2500 1% Open 98" Wide Fabric Fiberglass / PVC SheerWeave 2701 1% Open 98" Wide Fabric Fiberglass / PVC SheerWeave 4800 1% Open 98" Wide Fabric Fiberglass / PVC Side 24 36 48 60 72 84 96 108 120 132 144 156 Channels 36 118 150 183 214 275 318 334 425 745 811 880 1202 70 48 130 165 201 238 304 352 370 587 747 818 887 1209 93 60 142 183 224 263 330 390 454 590 753 822 891 1213 116 72 153 198 242 286 362 424 491 593 755 826 894 1216 139 84 164 215 264 312 391 460 525 619 956 1048 1133 1491 162 96 200 257 313 368 424 502 567 880 964 1061 1147 1509 185 108 214 273 334 394 452 537 604 885 966 1065 1152 1516 208 120 238 296 355 419 483 573 640 888 972 1073 1161 1523 231 132 278 345 410 482 554 654 677 1049 1150 1270 1377 1768 254 144 288 361 431 507 584 691 714 1053 1159 1275 1381 1774 277 156 331 419 507 601 693 824 858 1065 1173 1436 1556 1800 300 Shades under dashed line will be railroaded and have a visible seam Fascia & Headbox Accessories Additional Options: 24 36 48 60 72 84 96 108 120 132 144 156 3" & 4" Square Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Round Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Fabric Wrapped Fascia 89 110 131 152 173 194 215 236 257 278 299 320 Shade Pocket (Without Lip) 132 169 206 243 280 319 355 391 428 465 502 539 Shade Pocket with Lip 132 169 206 243 280 319 355 391 428 465 502 539 Dual Shade Pocket (Without Lip) 210 289 368 447 526 605 684 763 842 921 1000 1079 Closure Plate for Pocket 17 24 31 38 45 50 58 66 73 80 87 94 Hanger with Closure Plate 21 33 45 57 69 81 93 105 117 129 141 153 Inserted Fabric Valance 24 30 36 42 48 54 60 66 72 78 84 90 Ceiling "L" Fascia 51 70 89 108 127 146 165 184 203 222 241 260 Sill Channel 24 35 46 57 68 79 90 101 112 123 134 145 Cassette Commercial w/fascia 100 140 180 220 260 300 340 380 420 N/A N/A N/A Cassette Retail w/fabric Insert 63 82 101 120 139 158 177 N/A N/A N/A N/A N/A Roller Shade Surcharge Options Stainless Steel Chain $12.00 White or Black Steel Chain $24.00 Platinum Clutch with Steel Chain $10.00 Net External Aluminum Hembar $10.00 Wrapped Hembar $15.00 Spring Assisted Clutch Shade $125.00 Exterior Shade Guide Wire System $120.00 Bottom-Up Shade with Clutch $275.00 Multiple Band Motorized Shades 1. Price each band separately and add together 2. Price each coupler surcharge and add together 3. Add shade band and coupler prices together Straight Line Coupler $100.00 90 o Corner Coupler $200.00 Important Items To Note: Screen fabrics will be fabricated vertically or horizontally (railroaded) at the factory's discretion. Any shades wider and longer than the fabric's width will have one or more visible seams (splices). The maximum warrantied size of a clutch operated shade is 126" x 144". Large Clutch shades may require a spring assisted lifting mechanism. Please note the Clutch Fabrication Chart on page 39 for specific size requirements. Side channel surcharge includes left & right channels. Seal brushes available upon request. Prices for valances, boxes, and pockets include all brackets and end caps. Reverse roll option is not available for square, round, or wrapped fabric fascias. The size of a shade will determine the size of the tube used; upgrades to larger tubes will be available upon request. Please review the clutch fabrication chart on page 39 & 40. Shades exceeding a 3-to-1 ratio may have problems tracking. In other words, shades with a height dimension that is more than 3 times the width measurement may be susceptible to telescoping. All measurements must be bracket to bracket. Shades up to 92" in width shipped via FedEx: $ 4.00 / unit Net Freight Charge Shades 92 1/8" to 125" in width shipped via FedEx: $ 75.00 / unit Net Freight Charge Shades 125 1/8" or greater in width shipped via Common Carrier: $ 150.00 per shipment 8-11-11 kb (33)

Length Suggested Retail Price Table 7.1 (SW5000) Sun Control Roller Shades SheerWeave 5000 Varies (Based on Color) 98" Wide Fabric Fiberglass / PVC Side 24 36 48 60 72 84 96 108 120 132 144 156 Channels 36 118 150 183 214 275 318 334 70 48 130 165 201 238 304 352 370 93 60 142 183 224 263 330 390 454 116 This fabric has a distinctive 72 153 198 242 286 362 424 491 139 84 164 215 264 312 391 460 525 pattern and should not be 162 96 200 257 313 368 424 502 567 railroaded. The maximum 185 108 214 273 334 394 452 537 604 width of a shade using the above 208 120 238 296 355 419 483 573 640 listed fabrics is 98". 231 132 278 345 410 482 554 654 677 254 144 288 361 431 507 584 691 714 277 156 331 419 507 601 693 824 858 300 Fascia & Headbox Accessories Additional Options: 24 36 48 60 72 84 96 108 120 132 144 156 3" & 4" Square Aluminum Fascia 45 55 65 75 85 95 105 3" & 4" Round Aluminum Fascia 45 55 65 75 85 95 105 3" & 4" Fabric Wrapped Fascia 89 110 131 152 173 194 215 Shade Pocket (Without Lip) 132 169 206 243 280 319 355 Shade Pocket with Lip 132 169 206 243 280 319 355 Dual Shade Pocket (Without Lip) 210 289 368 447 526 605 684 Closure Plate for Pocket 17 24 31 38 45 50 58 Hanger with Closure Plate 21 33 45 57 69 81 93 Inserted Fabric Valance 24 30 36 42 48 54 60 Ceiling "L" Fascia 51 70 89 108 127 146 165 Sill Channel 24 35 46 57 68 79 90 Cassette Commercial w/fascia 100 140 180 220 260 300 340 Cassette Retail w/fabric Insert 63 82 101 120 139 158 177 This fabric has a distinctive pattern and should not be railroaded. The maximum width of a shade using the above listed fabrics is 98". Roller Shade Surcharge Options Stainless Steel Chain $12.00 White or Black Steel Chain $24.00 Platinum Clutch with Steel Chain $10.00 Net External Aluminum Hembar $10.00 Wrapped Hembar $15.00 Spring Assisted Clutch Shade $125.00 Exterior Shade Guide Wire System $120.00 Bottom-Up Shade with Clutch $275.00 Multiple Band Motorized Shades 1. Price each band separately and add together 2. Price each coupler surcharge and add together 3. Add shade band and coupler prices together Straight Line Coupler $100.00 90 o Corner Coupler $200.00 Important Items To Note: Screen fabrics will be fabricated vertically or horizontally (railroaded) at the factory's discretion. Any shades wider and longer than the fabric's width will have one or more visible seams (splices). The maximum warrantied size of a clutch operated shade is 126" x 144". Large Clutch shades may require a spring assisted lifting mechanism. Please note the Clutch Fabrication Chart on page 39 for specific size requirements. Side channel surcharge includes left & right channels. Seal brushes available upon request. Prices for valances, boxes, and pockets include all brackets and end caps. Reverse roll option is not available for square, round, or wrapped fabric fascias. The size of a shade will determine the size of the tube used; upgrades to larger tubes will be available upon request. Please review the clutch fabrication chart on page 39 & 40. Shades exceeding a 3-to-1 ratio may have problems tracking. In other words, shades with a height dimension that is more than 3 times the width measurement may be susceptible to telescoping. All measurements must be bracket to bracket. Shades up to 92" in width shipped via FedEx: $ 4.00 / unit Net Freight Charge Shades 92 1/8" to 125" in width shipped via FedEx: $ 75.00 / unit Net Freight Charge Shades 125 1/8" or greater in width shipped via Common Carrier: $ 150.00 per shipment 8-11-11 kb (34)

Length Suggested Retail Price Table 8 (Deco2) Sun Control Roller Shades Diamonds (PVC-Free) Light Filtering 120" Wide Fabric Polyester Marblite (PVC-Free) Light Filtering 120" Wide Fabric Polyester Vineyard (PVC-Free) Light Filtering 120" Wide Fabric Polyester Side 24 36 48 60 72 84 96 108 120 132 144 156 Channels 36 121 153 187 219 282 325 342 360 378 70 48 133 168 206 243 311 361 378 398 413 This fabric has a 93 60 145 187 229 269 339 398 465 489 515 distinctive pattern 116 72 157 202 248 292 370 433 502 529 557 and should not be 139 84 167 220 270 320 399 472 538 566 596 railroaded. 162 96 205 263 321 376 433 514 580 611 643 185 108 219 280 342 404 462 550 619 651 686 The maximum 208 120 243 303 364 430 495 586 655 689 725 width of a shade 231 132 284 353 419 494 566 669 692 729 767 using the above 254 144 294 369 440 518 598 707 731 770 810 listed fabrics is 118". 277 156 340 430 518 615 710 844 878 924 973 300 Fascia & Headbox Accessories Additional Options: 24 36 48 60 72 84 96 108 120 132 144 156 3" & 4" Square Aluminum Fascia 45 55 65 75 85 95 105 115 125 3" & 4" Round Aluminum Fascia 45 55 65 75 85 95 105 115 125 3" & 4" Fabric Wrapped Fascia 89 110 131 152 173 194 215 236 257 Shade Pocket (Without Lip) 132 169 206 243 280 319 355 391 428 Shade Pocket with Lip 132 169 206 243 280 319 355 391 428 Dual Shade Pocket (Without Lip) 210 289 368 447 526 605 684 763 842 Closure Plate for Pocket 17 24 31 38 45 50 58 66 73 Hanger with Closure Plate 21 33 45 57 69 81 93 105 117 Inserted Fabric Valance 24 30 36 42 48 54 60 66 72 Ceiling "L" Fascia 51 70 89 108 127 146 165 184 203 Sill Channel 24 35 46 57 68 79 90 101 112 Cassette Commercial w/fascia 100 140 180 220 260 300 340 380 420 Cassette Retail w/fabric Insert 63 82 101 120 139 158 177 N/A N/A This fabric has a distinctive pattern and should not be railroaded. The maximum width of a shade using the above listed fabrics is 118". Roller Shade Surcharge Options Stainless Steel Chain $12.00 White or Black Steel Chain $24.00 Platinum Clutch with Steel Chain $10.00 Net External Aluminum Hembar $10.00 Wrapped Hembar $15.00 Spring Assisted Clutch Shade $125.00 Exterior Shade Guide Wire System $120.00 Bottom-Up Shade with Clutch $275.00 Multiple Band Motorized Shades 1. Price each band separately and add together 2. Price each coupler surcharge and add together 3. Add shade band and coupler prices together Straight Line Coupler $100.00 90 o Corner Coupler $200.00 Important Items To Note: Screen fabrics will be fabricated vertically or horizontally (railroaded) at the factory's discretion. Any shades wider and longer than the fabric's width will have one or more visible seams (splices). The maximum warrantied size of a clutch operated shade is 126" x 144". Large Clutch shades may require a spring assisted lifting mechanism. Please note the Clutch Fabrication Chart on page 39 for specific size requirements. Side channel surcharge includes left & right channels. Seal brushes available upon request. Prices for valances, boxes, and pockets include all brackets and end caps. Reverse roll option is not available for square, round, or wrapped fabric fascias. The size of a shade will determine the size of the tube used; upgrades to larger tubes will be available upon request. Please review the clutch fabrication chart on page 39 & 40. Shades exceeding a 3-to-1 ratio may have problems tracking. In other words, shades with a height dimension that is more than 3 times the width measurement may be susceptible to telescoping. All measurements must be bracket to bracket. Shades up to 92" in width shipped via FedEx: $ 4.00 / unit Net Freight Charge Shades 92 1/8" to 125" in width shipped via FedEx: $ 75.00 / unit Net Freight Charge Shades 125 1/8" or greater in width shipped via Common Carrier: $ 150.00 per shipment (35) 8-11-11 kb

Length Suggested Retail Price Table 9 Sun Control Roller Shades SheerWeave 7100 0% Open 72" Wide Fabric Fiberglass / PVC Side 24 36 48 60 72 84 96 108 120 132 144 156 Channels 36 123 156 191 222 286 330 347 441 773 843 916 1249 70 48 136 172 209 247 315 366 385 611 776 850 922 1256 93 60 149 191 233 273 344 406 471 614 783 853 926 1260 116 72 159 206 251 298 377 439 511 616 785 858 929 1264 139 84 171 223 276 325 407 479 546 643 993 1090 1178 1549 162 96 208 267 327 384 439 521 591 916 1002 1103 1192 1568 185 108 222 285 347 410 471 559 628 919 1004 1107 1199 1574 208 120 247 308 371 436 502 597 665 922 1011 1116 1206 1582 231 132 289 359 427 502 576 680 703 1091 1195 1319 1431 1838 254 144 301 375 448 528 607 719 742 1094 1205 1326 1437 1844 277 156 346 436 528 625 722 856 891 1107 1218 1493 1616 1871 300 Shades under dashed line will be railroaded and have a visible seam Fascia & Headbox Accessories Additional Options: 24 36 48 60 72 84 96 108 120 132 144 156 3" & 4" Square Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Round Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Fabric Wrapped Fascia 89 110 131 152 173 194 215 236 257 278 299 320 Shade Pocket (Without Lip) 132 169 206 243 280 319 355 391 428 465 502 539 Shade Pocket with Lip 132 169 206 243 280 319 355 391 428 465 502 539 Dual Shade Pocket (Without Lip) 210 289 368 447 526 605 684 763 842 921 1000 1079 Closure Plate for Pocket 17 24 31 38 45 50 58 66 73 80 87 94 Hanger with Closure Plate 21 33 45 57 69 81 93 105 117 129 141 153 Inserted Fabric Valance 24 30 36 42 48 54 60 66 72 78 84 90 Ceiling "L" Fascia 51 70 89 108 127 146 165 184 203 222 241 260 Sill Channel 24 35 46 57 68 79 90 101 112 123 134 145 Cassette Commercial w/fascia 100 140 180 220 260 300 340 380 420 N/A N/A N/A Cassette Retail w/fabric Insert 63 82 101 120 139 158 177 N/A N/A N/A N/A N/A Roller Shade Surcharge Options Stainless Steel Chain $12.00 White or Black Steel Chain $24.00 Platinum Clutch with Steel Chain $10.00 Net External Aluminum Hembar $10.00 Wrapped Hembar $15.00 Spring Assisted Clutch Shade $125.00 Exterior Shade Guide Wire System $120.00 Bottom-Up Shade with Clutch $275.00 Important Items To Note: Screen fabrics will be fabricated vertically or horizontally (railroaded) at the factory's discretion. Any shades wider and longer than the fabric's width will have one or more visible seams (splices). The maximum warrantied size of a clutch operated shade is 126" x 144". Large Clutch shades may require a spring assisted lifting mechanism. Please note the Clutch Fabrication Chart on page 39 for specific size requirements. Side channel surcharge includes left & right channels. Seal brushes available upon request. Prices for valances, boxes, and pockets include all brackets and end caps. Multiple Band Motorized Shades 1. Price each band separately and add together 2. Price each coupler surcharge and add together 3. Add shade band and coupler prices together Straight Line Coupler $100.00 90 o Corner Coupler $200.00 Reverse roll option is not available for square, round, or wrapped fabric fascias. All measurements must be bracket to bracket. Shades up to 92" in width shipped via FedEx: $ 4.00 / unit Net Freight Charge Shades 92 1/8" to 125" in width shipped via FedEx: $ 75.00 / unit Net Freight Charge Shades 125 1/8" or greater in width shipped via Common Carrier: $ 150.00 per shipment The size of a shade will determine the size of the tube used; upgrades to larger tubes will be available upon request. Please review the clutch fabrication chart on page 39 & 40. Shades exceeding a 3-to-1 ratio may have problems tracking. In other words, shades with a height dimension that is more than 3 times the width measurement may be susceptible to telescoping. (36) 8-11-11 kb

Length Suggested Retail Price Table 10 Sun Control Roller Shades Noblette (PVC-Free) Translucent 110" Wide Fabric Polyester Side 24 36 48 60 72 84 96 108 110 132 144 156 Channels 36 129 162 199 231 299 345 363 382 402 70 48 141 179 219 258 330 383 403 424 446 This fabric has a 93 60 155 199 244 286 360 424 493 519 546 distinctive pattern 116 72 166 215 263 310 393 460 534 562 592 and should not be 139 84 178 234 287 340 425 501 572 602 633 162 railroaded. 96 218 279 341 399 460 545 617 649 683 185 The maximum 108 231 298 363 429 492 583 658 691 728 208 width of a shade 120 258 321 387 456 525 623 696 732 771 231 132 302 375 446 524 602 711 735 774 815 using the above 254 144 313 392 468 551 635 751 776 817 860 listed fabrics is 110". 277 156 361 456 551 654 754 896 933 982 1034 300 Fascia & Headbox Accessories Additional Options: 24 36 48 60 72 84 96 108 120 132 144 156 3" & 4" Square Aluminum Fascia 45 55 65 75 85 95 105 115 125 3" & 4" Round Aluminum Fascia 45 55 65 75 85 95 105 115 125 3" & 4" Fabric Wrapped Fascia 89 110 131 152 173 194 215 236 257 Shade Pocket (Without Lip) 132 169 206 243 280 319 355 391 428 Shade Pocket with Lip 132 169 206 243 280 319 355 391 428 Dual Shade Pocket (Without Lip) 210 289 368 447 526 605 684 763 842 Closure Plate for Pocket 17 24 31 38 45 50 58 66 73 Hanger with Closure Plate 21 33 45 57 69 81 93 105 117 Inserted Fabric Valance 24 30 36 42 48 54 60 66 72 Ceiling "L" Fascia 51 70 89 108 127 146 165 184 203 Sill Channel 24 35 46 57 68 79 90 101 112 Cassette Commercial w/fascia 100 140 180 220 260 300 340 380 420 Cassette Retail w/fabric Insert 63 82 101 120 139 158 177 N/A N/A This fabric has a distinctive pattern and should not be railroaded. The maximum width of a shade using the above listed fabrics is 110". Roller Shade Surcharge Options Stainless Steel Chain $12.00 White or Black Steel Chain $24.00 Platinum Clutch with Steel Chain $10.00 Net External Aluminum Hembar $10.00 Wrapped Hembar $15.00 Spring Assisted Clutch Shade $125.00 Exterior Shade Guide Wire System $120.00 Bottom-Up Shade with Clutch $275.00 Important Items To Note: Screen fabrics will be fabricated vertically or horizontally (railroaded) at the factory's discretion. Any shades wider and longer than the fabric's width will have one or more visible seams (splices). The maximum warrantied size of a clutch operated shade is 126" x 144". Large Clutch shades may require a spring assisted lifting mechanism. Please note the Clutch Fabrication Chart on page 39 for specific size requirements. Side channel surcharge includes left & right channels. Seal brushes available upon request. Prices for valances, boxes, and pockets include all brackets and end caps. Multiple Band Motorized Shades 1. Price each band separately and add together 2. Price each coupler surcharge and add together 3. Add shade band and coupler prices together Straight Line Coupler $100.00 90 o Corner Coupler $200.00 Reverse roll option is not available for square, round, or wrapped fabric fascias. All measurements must be bracket to bracket. Shades up to 92" in width shipped via FedEx: $ 4.00 / unit Net Freight Charge Shades 92 1/8" to 125" in width shipped via FedEx: $ 75.00 / unit Net Freight Charge Shades 125 1/8" or greater in width shipped via Common Carrier: $ 150.00 per shipment The size of a shade will determine the size of the tube used; upgrades to larger tubes will be available upon request. Please review the clutch fabrication chart on page 39 & 40. Shades exceeding a 3-to-1 ratio may have problems tracking. In other words, shades with a height dimension that is more than 3 times the width measurement may be susceptible to telescoping. 8-11-11 kb (37)

Length Suggested Retail Price Table 11 Sun Control Roller Shades SheerWeave 7000 0% Open 94" Wide Fabric Polyester / Acrylic Backing *** Please note: Shades over 94" (not 96") in width and greater than 84" in length will have a visible seam. Side 24 36 48 60 72 84 96 108 120 132 144 156 Channels 36 160 203 248 289 373 431 454 577 1012 1102 1197 1633 70 48 177 224 273 323 413 478 503 798 1015 1111 1205 1644 93 60 193 248 305 357 449 530 616 802 1023 1117 1210 1648 116 72 207 268 329 388 492 575 667 805 1026 1122 1215 1653 139 84 222 291 359 425 531 626 714 840 1298 1425 1540 2027 162 96 271 349 426 499 575 682 770 1197 1310 1441 1560 2052 185 108 289 372 454 536 615 729 822 1202 1313 1448 1566 2060 208 120 323 402 483 571 657 779 869 1207 1320 1458 1578 2070 231 132 376 469 557 656 752 889 919 1426 1563 1726 1872 2403 254 144 391 490 585 688 793 939 971 1430 1574 1733 1878 2411 277 156 451 571 688 816 942 1120 1166 1448 1594 1951 2114 2447 300 Shades under dashed line will be railroaded and have a visible seam Fascia & Headbox Accessories Additional Options: 24 36 48 60 72 84 96 108 120 132 144 156 3" & 4" Square Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Round Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Fabric Wrapped Fascia 89 110 131 152 173 194 215 236 257 278 299 320 Shade Pocket (Without Lip) 132 169 206 243 280 319 355 391 428 465 502 539 Shade Pocket with Lip 132 169 206 243 280 319 355 391 428 465 502 539 Dual Shade Pocket (Without Lip) 210 289 368 447 526 605 684 763 842 921 1000 1079 Closure Plate for Pocket 17 24 31 38 45 50 58 66 73 80 87 94 Hanger with Closure Plate 21 33 45 57 69 81 93 105 117 129 141 153 Inserted Fabric Valance 24 30 36 42 48 54 60 66 72 78 84 90 Ceiling "L" Fascia 51 70 89 108 127 146 165 184 203 222 241 260 Sill Channel 24 35 46 57 68 79 90 101 112 123 134 145 Cassette Commercial w/fascia 100 140 180 220 260 300 340 380 420 N/A N/A N/A Cassette Retail w/fabric Insert 63 82 101 120 139 158 177 N/A N/A N/A N/A N/A Roller Shade Surcharge Options Stainless Steel Chain $12.00 White or Black Steel Chain $24.00 Platinum Clutch with Steel Chain $10.00 Net External Aluminum Hembar $10.00 Wrapped Hembar $15.00 Spring Assisted Clutch Shade $125.00 Exterior Shade Guide Wire System $120.00 Bottom-Up Shade with Clutch $275.00 Multiple Band Motorized Shades 1. Price each band separately and add together 2. Price each coupler surcharge and add together 3. Add shade band and coupler prices together Straight Line Coupler $100.00 90 o Corner Coupler $200.00 Important Items To Note: Screen fabrics will be fabricated vertically or horizontally (railroaded) at the factory's discretion. Any shades wider and longer than the fabric's width will have one or more visible seams (splices). The maximum warrantied size of a clutch operated shade is 126" x 144". Large Clutch shades may require a spring assisted lifting mechanism. Please note the Clutch Fabrication Chart on page 39 for specific size requirements. Side channel surcharge includes left & right channels. Seal brushes available upon request. Prices for valances, boxes, and pockets include all brackets and end caps. Reverse roll option is not available for square, round, or wrapped fabric fascias. The size of a shade will determine the size of the tube used; upgrades to larger tubes will be available upon request. Please review the clutch fabrication chart on page 39 & 40. Shades exceeding a 3-to-1 ratio may have problems tracking. In other words, shades with a height dimension that is more than 3 times the width measurement may be susceptible to telescoping. All measurements must be bracket to bracket. Shades up to 92" in width shipped via FedEx: $ 4.00 / unit Net Freight Charge Shades 92 1/8" to 125" in width shipped via FedEx: $ 75.00 / unit Net Freight Charge Shades 125 1/8" or greater in width shipped via Common Carrier: $ 150.00 per shipment 8-11-11 kb (38)

Length Suggested Retail Price Table 12 Sun Control Roller Shades SheerWeave Infinity 5% (PVC-Free) 5% Open 98" Wide Fabric Poly-Olefin Side 24 36 48 60 72 84 96 108 120 132 144 156 Channels 36 186 236 289 336 434 501 528 671 1176 1281 1393 1901 70 48 205 261 318 375 480 557 585 929 1181 1293 1402 1911 93 60 224 289 354 415 522 616 717 933 1190 1299 1407 1918 116 72 242 312 383 452 572 669 776 936 1194 1305 1414 1923 139 84 259 339 417 494 618 728 831 978 1511 1658 1792 2359 162 96 315 406 495 581 669 793 896 1393 1524 1677 1815 2387 185 108 336 432 528 623 714 849 956 1398 1528 1685 1822 2397 208 120 375 467 562 663 765 906 1011 1404 1536 1696 1836 2408 231 132 438 545 648 763 875 1034 1070 1659 1818 2007 2177 2796 254 144 455 570 681 801 923 1092 1129 1664 1832 2016 2184 2805 277 156 524 663 801 950 1097 1302 1356 1685 1855 2271 2460 2847 300 Shades under dashed line will be railroaded and have a visible seam Fascia & Headbox Accessories Additional Options: 24 36 48 60 72 84 96 108 120 132 144 156 3" & 4" Square Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Round Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Fabric Wrapped Fascia 89 110 131 152 173 194 215 236 257 278 299 320 Shade Pocket (Without Lip) 132 169 206 243 280 319 355 391 428 465 502 539 Shade Pocket with Lip 132 169 206 243 280 319 355 391 428 465 502 539 Dual Shade Pocket (Without Lip) 210 289 368 447 526 605 684 763 842 921 1000 1079 Closure Plate for Pocket 17 24 31 38 45 50 58 66 73 80 87 94 Hanger with Closure Plate 21 33 45 57 69 81 93 105 117 129 141 153 Inserted Fabric Valance 24 30 36 42 48 54 60 66 72 78 84 90 Ceiling "L" Fascia 51 70 89 108 127 146 165 184 203 222 241 260 Sill Channel 24 35 46 57 68 79 90 101 112 123 134 145 Cassette Commercial w/fascia 100 140 180 220 260 300 340 380 420 N/A N/A N/A Cassette Retail w/fabric Insert 63 82 101 120 139 158 177 N/A N/A N/A N/A N/A Roller Shade Surcharge Options Stainless Steel Chain $12.00 White or Black Steel Chain $24.00 Platinum Clutch with Steel Chain $10.00 Net External Aluminum Hembar $10.00 Wrapped Hembar $15.00 Spring Assisted Clutch Shade $125.00 Exterior Shade Guide Wire System $120.00 Bottom-Up Shade with Clutch $275.00 Multiple Band Motorized Shades 1. Price each band separately and add together 2. Price each coupler surcharge and add together 3. Add shade band and coupler prices together Straight Line Coupler $100.00 90 o Corner Coupler $200.00 Important Items To Note: Screen fabrics will be fabricated vertically or horizontally (railroaded) at the factory's discretion. Any shades wider and longer than the fabric's width will have one or more visible seams (splices). The maximum warrantied size of a clutch operated shade is 126" x 144". Large Clutch shades may require a spring assisted lifting mechanism. Please note the Clutch Fabrication Chart on page 39 for specific size requirements. Side channel surcharge includes left & right channels. Seal brushes available upon request. Prices for valances, boxes, and pockets include all brackets and end caps. Reverse roll option is not available for square, round, or wrapped fabric fascias. The size of a shade will determine the size of the tube used; upgrades to larger tubes will be available upon request. Please review the clutch fabrication chart on page 39 & 40. Shades exceeding a 3-to-1 ratio may have problems tracking. In other words, shades with a height dimension that is more than 3 times the width measurement may be susceptible to telescoping. All measurements must be bracket to bracket. Shades up to 92" in width shipped via FedEx: $ 4.00 / unit Net Freight Charge Shades 92 1/8" to 125" in width shipped via FedEx: $ 75.00 / unit Net Freight Charge Shades 125 1/8" or greater in width shipped via Common Carrier: $ 150.00 per shipment 8-11-11 kb (39)

Length Suggested Retail Price Table 13 Sun Control Roller Shades SheerWeave Infinity 3% (PVC-Free) 3% Open 98" Wide Fabric Poly-Olefin Side 24 36 48 60 72 84 96 108 120 132 144 156 Channels 36 204 259 318 370 477 551 580 738 1294 1410 1531 2090 70 48 225 286 349 412 528 612 643 1021 1298 1422 1542 2103 93 60 246 318 389 456 574 677 788 1025 1309 1428 1548 2109 116 72 265 343 425 496 628 735 853 1029 1313 1435 1554 2115 139 84 284 372 458 542 679 801 914 1076 1662 1823 1970 2594 162 96 347 446 544 639 735 872 985 1531 1676 1844 1995 2625 185 108 370 475 580 685 786 933 1050 1538 1680 1853 2004 2636 208 120 412 513 618 729 840 996 1111 1544 1689 1865 2019 2649 231 132 481 599 712 838 962 1137 1176 1825 2000 2208 2394 3075 254 144 500 626 748 880 1015 1202 1242 1830 2014 2218 2403 3085 277 156 576 729 880 1044 1206 1433 1491 1853 2040 2497 2705 3132 300 Shades under dashed line will be railroaded and have a visible seam Fascia & Headbox Accessories Additional Options: 24 36 48 60 72 84 96 108 120 132 144 156 3" & 4" Square Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Round Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Fabric Wrapped Fascia 89 110 131 152 173 194 215 236 257 278 299 320 Shade Pocket (Without Lip) 132 169 206 243 280 319 355 391 428 465 502 539 Shade Pocket with Lip 132 169 206 243 280 319 355 391 428 465 502 539 Dual Shade Pocket (Without Lip) 210 289 368 447 526 605 684 763 842 921 1000 1079 Closure Plate for Pocket 17 24 31 38 45 50 58 66 73 80 87 94 Hanger with Closure Plate 21 33 45 57 69 81 93 105 117 129 141 153 Inserted Fabric Valance 24 30 36 42 48 54 60 66 72 78 84 90 Ceiling "L" Fascia 51 70 89 108 127 146 165 184 203 222 241 260 Sill Channel 24 35 46 57 68 79 90 101 112 123 134 145 Cassette Commercial w/fascia 100 140 180 220 260 300 340 380 420 N/A N/A N/A Cassette Retail w/fabric Insert 63 82 101 120 139 158 177 N/A N/A N/A N/A N/A Roller Shade Surcharge Options Stainless Steel Chain $12.00 White or Black Steel Chain $24.00 Platinum Clutch with Steel Chain $10.00 Net External Aluminum Hembar $10.00 Wrapped Hembar $15.00 Spring Assisted Clutch Shade $125.00 Exterior Shade Guide Wire System $120.00 Bottom-Up Shade with Clutch $275.00 Multiple Band Motorized Shades 1. Price each band separately and add together 2. Price each coupler surcharge and add together 3. Add shade band and coupler prices together Straight Line Coupler $100.00 90 o Corner Coupler $200.00 Important Items To Note: Screen fabrics will be fabricated vertically or horizontally (railroaded) at the factory's discretion. Any shades wider and longer than the fabric's width will have one or more visible seams (splices). The maximum warrantied size of a clutch operated shade is 126" x 144". Large Clutch shades may require a spring assisted lifting mechanism. Please note the Clutch Fabrication Chart on page 39 for specific size requirements. Side channel surcharge includes left & right channels. Seal brushes available upon request. Prices for valances, boxes, and pockets include all brackets and end caps. Reverse roll option is not available for square, round, or wrapped fabric fascias. The size of a shade will determine the size of the tube used; upgrades to larger tubes will be available upon request. Please review the clutch fabrication chart on page 39 & 40. Shades exceeding a 3-to-1 ratio may have problems tracking. In other words, shades with a height dimension that is more than 3 times the width measurement may be susceptible to telescoping. All measurements must be bracket to bracket. Shades up to 92" in width shipped via FedEx: $ 4.00 / unit Net Freight Charge Shades 92 1/8" to 125" in width shipped via FedEx: $ 75.00 / unit Net Freight Charge Shades 125 1/8" or greater in width shipped via Common Carrier: $ 150.00 per shipment 8-11-11 kb (40)

Length Suggested Retail Price Table 13.1 Sun Control Roller Shades Suede 0% Open 78" Wide Fabric Polyester / Acrylic Backing Side 24 36 48 60 72 78 96 108 120 132 144 156 Channels 36 204 259 318 370 477 551 70 48 225 286 349 412 528 612 93 60 246 318 389 456 574 677 116 72 265 343 420 496 628 735 This fabric has a distinctive pattern and 139 84 284 372 458 542 679 801 162 should not be railroaded. The maximum 96 347 446 544 639 735 872 185 width of a shade using the above listed 108 370 475 580 685 786 933 208 fabrics is 78". 120 412 513 618 729 840 996 231 132 481 599 712 838 962 1137 254 144 500 626 748 880 1015 1202 277 156 576 729 880 1044 1206 1433 300 Additional Options: 24 36 48 60 72 84 96 108 120 132 144 156 3" & 4" Square Aluminum Fascia 45 55 65 75 85 95 3" & 4" Round Aluminum Fascia 45 55 65 75 85 95 3" & 4" Fabric Wrapped Fascia 89 110 131 152 173 194 Shade Pocket (Without Lip) 132 169 206 243 280 319 Shade Pocket with Lip 132 169 206 243 280 319 Dual Shade Pocket (Without Lip) 210 289 368 447 526 605 Closure Plate for Pocket 17 24 31 38 45 50 Hanger with Closure Plate 21 33 45 57 69 81 Inserted Fabric Valance 24 30 36 42 48 54 Ceiling "L" Fascia 51 70 89 108 127 146 Sill Channel 24 35 46 57 68 79 Cassette Commercial w/fascia 100 140 180 220 260 300 Cassette Retail w/fabric Insert 63 82 101 120 139 158 Roller Shade Surcharge Options Stainless Steel Chain $12.00 White or Black Steel Chain $24.00 Platinum Clutch with Steel Chain $10.00 Net External Aluminum Hembar $10.00 Wrapped Hembar $15.00 Spring Assisted Clutch Shade $125.00 Exterior Shade Guide Wire System $120.00 Bottom-Up Shade with Clutch $275.00 Multiple Band Motorized Shades 1. Price each band separately and add together 2. Price each coupler surcharge and add together 3. Add shade band and coupler prices together Straight Line Coupler $100.00 90 o Corner Coupler $200.00 Fascia & Headbox Accessories Important Items To Note: All measurements must be bracket to bracket. Shades up to 92" in width shipped via FedEx: $ 4.00 / unit Net Freight Charge Shades 92 1/8" to 125" in width shipped via FedEx: $ 75.00 / unit Net Freight Charge Shades 125 1/8" or greater in width shipped via Common Carrier: $ 150.00 per shipment This fabric has a distinctive pattern and should not be railroaded. The maximum width of a shade using the above listed fabrics is 78". Screen fabrics will be fabricated vertically or horizontally (railroaded) at the factory's discretion. Any shades wider and longer than the fabric's width will have one or more visible seams (splices). The maximum warrantied size of a clutch operated shade is 126" x 144". Large Clutch shades may require a spring assisted lifting mechanism. Please note the Clutch Fabrication Chart on page 39 for specific size requirements. Side channel surcharge includes left & right channels. Seal brushes available upon request. Prices for valances, boxes, and pockets include all brackets and end caps. Reverse roll option is not available for square, round, or wrapped fabric fascias. The size of a shade will determine the size of the tube used; upgrades to larger tubes will be available upon request. Please review the clutch fabrication chart on page 39 & 40. Shades exceeding a 3-to-1 ratio may have problems tracking. In other words, shades with a height dimension that is more than 3 times the width measurement may be susceptible to telescoping. (41) 8-11-11 kb

Length Suggested Retail Price Table 14 Sun Control Roller Shades SheerWeave Performance Plus 2390 5% Open 96" Wide Fabric Metallized Fabric Side 24 36 48 60 72 84 96 108 120 132 144 156 Channels 36 242 306 376 437 564 651 686 873 1529 1666 1811 2471 70 48 267 339 413 488 624 724 761 1207 1535 1680 1823 2485 93 60 291 376 460 540 679 801 932 1212 1547 1689 1830 2493 116 72 314 406 497 587 743 870 1010 1216 1552 1696 1838 2499 139 84 336 440 542 642 803 947 1080 1271 1965 2156 2329 3066 162 96 410 528 643 755 870 1032 1165 1811 1981 2180 2359 3103 185 108 437 561 686 810 929 1103 1243 1817 1987 2190 2369 3116 208 120 488 606 731 861 994 1178 1314 1825 1997 2205 2386 3131 231 132 570 709 843 992 1138 1143 1392 2157 2363 2609 2830 3635 254 144 592 741 885 1041 1201 1420 1468 2162 2381 2621 2840 3646 277 156 682 861 1041 1234 1425 1693 1762 2190 2411 2952 3198 3701 300 Shades under dashed line will be railroaded and have a visible seam Fascia & Headbox Accessories Additional Options: 24 36 48 60 72 84 96 108 120 132 144 156 3" & 4" Square Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Round Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Fabric Wrapped Fascia 89 110 131 152 173 194 215 236 257 278 299 320 Shade Pocket (Without Lip) 132 169 206 243 280 319 355 391 428 465 502 539 Shade Pocket with Lip 132 169 206 243 280 319 355 391 428 465 502 539 Dual Shade Pocket (Without Lip) 210 289 368 447 526 605 684 763 842 921 1000 1079 Closure Plate for Pocket 17 24 31 38 45 50 58 66 73 80 87 94 Hanger with Closure Plate 21 33 45 57 69 81 93 105 117 129 141 153 Inserted Fabric Valance 24 30 36 42 48 54 60 66 72 78 84 90 Ceiling "L" Fascia 51 70 89 108 127 146 165 184 203 222 241 260 Sill Channel 24 35 46 57 68 79 90 101 112 123 134 145 Cassette Commercial w/fascia 100 140 180 220 260 300 340 380 420 N/A N/A N/A Cassette Retail w/fabric Insert 63 82 101 120 139 158 177 N/A N/A N/A N/A N/A Roller Shade Surcharge Options Stainless Steel Chain $12.00 White or Black Steel Chain $24.00 Platinum Clutch with Steel Chain $10.00 Net External Aluminum Hembar $10.00 Wrapped Hembar $15.00 Spring Assisted Clutch Shade $125.00 Exterior Shade Guide Wire System $120.00 Bottom-Up Shade with Clutch $275.00 Multiple Band Motorized Shades 1. Price each band separately and add together 2. Price each coupler surcharge and add together 3. Add shade band and coupler prices together Straight Line Coupler $100.00 90 o Corner Coupler $200.00 Important Items To Note: Screen fabrics will be fabricated vertically or horizontally (railroaded) at the factory's discretion. Any shades wider and longer than the fabric's width will have one or more visible seams (splices). The maximum warrantied size of a clutch operated shade is 126" x 144". Large Clutch shades may require a spring assisted lifting mechanism. Please note the Clutch Fabrication Chart on page 39 for specific size requirements. Side channel surcharge includes left & right channels. Seal brushes available upon request. Prices for valances, boxes, and pockets include all brackets and end caps. Reverse roll option is not available for square, round, or wrapped fabric fascias. The size of a shade will determine the size of the tube used; upgrades to larger tubes will be available upon request. Please review the clutch fabrication chart on page 39 & 40. Shades exceeding a 3-to-1 ratio may have problems tracking. In other words, shades with a height dimension that is more than 3 times the width measurement may be susceptible to telescoping. All measurements must be bracket to bracket. Shades up to 92" in width shipped via FedEx: $ 4.00 / unit Net Freight Charge Shades 92 1/8" to 125" in width shipped via FedEx: $ 75.00 / unit Net Freight Charge Shades 125 1/8" or greater in width shipped via Common Carrier: $ 150.00 per shipment 8-11-11 kb (42)

Length Suggested Retail Price Table 15 Sun Control Roller Shades SheerWeave Performance Plus 2410 3% Open 96" Wide Fabric Metallized Fabric Side 24 36 48 60 72 84 96 108 120 132 144 156 Channels 36 265 336 413 481 620 716 754 959 1682 1832 1991 2717 70 48 293 372 454 536 686 795 836 1327 1688 1849 2004 2733 93 60 320 413 506 593 746 880 1024 1333 1701 1857 2013 2741 116 72 344 445 546 645 817 959 1109 1338 1707 1865 2021 2750 139 84 369 484 596 705 882 1041 1188 1398 2160 2370 2561 3372 162 96 451 579 708 830 956 1133 1281 1991 2179 2397 2594 3413 185 108 481 617 754 890 1022 1213 1365 1999 2184 2408 2605 3427 208 120 536 667 803 948 1092 1295 1445 2007 2195 2425 2624 3443 231 132 626 779 926 1090 1251 1477 1529 2373 2599 2870 3113 3997 254 144 650 814 972 1144 1319 1562 1614 2378 2619 2883 3124 4011 277 156 749 948 1144 1357 1568 1862 1939 2408 2651 3246 3517 4071 300 Shades under dashed line will be railroaded and have a visible seam Fascia & Headbox Accessories Additional Options: 24 36 48 60 72 84 96 108 120 132 144 156 3" & 4" Square Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Round Aluminum Fascia 45 55 65 75 85 95 105 115 125 135 145 155 3" & 4" Fabric Wrapped Fascia 89 110 131 152 173 194 215 236 257 278 299 320 Shade Pocket (Without Lip) 132 169 206 243 280 319 355 391 428 465 502 539 Shade Pocket with Lip 132 169 206 243 280 319 355 391 428 465 502 539 Dual Shade Pocket (Without Lip) 210 289 368 447 526 605 684 763 842 921 1000 1079 Closure Plate for Pocket 17 24 31 38 45 50 58 66 73 80 87 94 Hanger with Closure Plate 21 33 45 57 69 81 93 105 117 129 141 153 Inserted Fabric Valance 24 30 36 42 48 54 60 66 72 78 84 90 Ceiling "L" Fascia 51 70 89 108 127 146 165 184 203 222 241 260 Sill Channel 24 35 46 57 68 79 90 101 112 123 134 145 Cassette Commercial w/fascia 100 140 180 220 260 300 340 380 420 N/A N/A N/A Cassette Retail w/fabric Insert 63 82 101 120 139 158 177 N/A N/A N/A N/A N/A Roller Shade Surcharge Options Stainless Steel Chain $12.00 White or Black Steel Chain $24.00 Platinum Clutch with Steel Chain $10.00 Net External Aluminum Hembar $10.00 Wrapped Hembar $15.00 Spring Assisted Clutch Shade $125.00 Exterior Shade Guide Wire System $120.00 Bottom-Up Shade with Clutch $275.00 Multiple Band Motorized Shades 1. Price each band separately and add together 2. Price each coupler surcharge and add together 3. Add shade band and coupler prices together Straight Line Coupler $100.00 90 o Corner Coupler $200.00 Important Items To Note: Screen fabrics will be fabricated vertically or horizontally (railroaded) at the factory's discretion. Any shades wider and longer than the fabric's width will have one or more visible seams (splices). The maximum warrantied size of a clutch operated shade is 126" x 144". Large Clutch shades may require a spring assisted lifting mechanism. Please note the Clutch Fabrication Chart on page 39 for specific size requirements. Side channel surcharge includes left & right channels. Seal brushes available upon request. Prices for valances, boxes, and pockets include all brackets and end caps. Reverse roll option is not available for square, round, or wrapped fabric fascias. The size of a shade will determine the size of the tube used; upgrades to larger tubes will be available upon request. Please review the clutch fabrication chart on page 39 & 40. Shades exceeding a 3-to-1 ratio may have problems tracking. In other words, shades with a height dimension that is more than 3 times the width measurement may be susceptible to telescoping. All measurements must be bracket to bracket. Shades up to 92" in width shipped via FedEx: $ 4.00 / unit Net Freight Charge Shades 92 1/8" to 125" in width shipped via FedEx: $ 75.00 / unit Net Freight Charge Shades 125 1/8" or greater in width shipped via Common Carrier: $ 150.00 per shipment 8-11-11 kb (43)

Length Manual Clutch & Tube Size Matrix 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120 126 132 144 156 162 36 42 48 54 60 1 1/4" Clutch & Tube - Available with 3" & 4" Fascia 1 3/4" Clutch & Tube - No Spring Assist Required - Available with 4" Fascia 66 72 78 1 1/2" Clutch & Tube Available with 3" & 4" Fascia 2-1/2" Steel Tube with Platinum Series Clutch & Spring Assist. When using a spring assist a surcharge will apply. Available with 4" Fascia. 84 90 96 102 108 114 120 1 3/4" Clutch & Tube - No Spring Assist Required - Available with 4" Fascia 126 132 138 144 150 1 3/4" Clutch & Tube - Spring Assist Required - When using a spring assist a surcharge will apply. Available with 4" Fascia. 1 3/4" Clutch & 2 1/2" Tube - Spring Assist Required. When using a spring assist a surcharge will apply. Available with 4" Fascia. 156 (44)

Length Motorized Tube Size Matrix 48 60 72 84 96 108 120 126 132 144 156 168 180 192 204 216 228 240 108 120 126 132 144 156 168 180 192 204 216 228 240 252 264 276 288 300 312 324 336 348 360 2-1/2" Motor Tube - Aluminum 3" Motor Tube - Aluminum 4" Motor Tube - Steel (45)

Page of 575 West Manville Street, Rancho Dominguez, CA 90220 Customer Service Fax: (800) 459-6999 / International Fax: (310) 763-1749 PH: (800) 562-7425 / (310) 661-4400 Purchase Order Roller Shades Account #: Company Name: Contact: Ship To Address: Phone: Purchase Order #: Sidemark: City: State: Zip: Fax: Date Required: Line Sidemark Qty Spring Control Mount 1 Length Fabric Type 2 Fabric Color 3 Lift Type 4 Assist 5 Lift Side 6 Length 7 Fabric Roll 8 Hembar Type 9 Valance 10 Channels 11 Side Sill Color 1 2 3 4 5 6 7 8 9 10 Purchase Order Footnotes: Motor Control Options: 1. Mount: (IM) - Inside Mount 7. Control Length: If desired, the control length may be specified. If RTS motors are selected, specify the required controls. (OM) - Outside Mount Standard Chain Length = 75% of the Shade Drop / Minimum Chain Length = 67% of the Shade Drop Radio Frequency (RTS) Controls: Quantity 2. Fabric Type: Specify the type of material. Standard AC Motor Cable Length = 6 Ft. / May be ordered up to 24 Ft. for an additional charge 1 Ch. - RTS Hand Held Transmitter 3. Fabric Color: Specify the color # and name. 8. Fabric Roll: (R) - Regular Roll (Standard - Fabric rolls off the back of the roller tube - Closest to the Glass) 5 Ch. - RTS Hand Held Transmitter 4. Lift Type: (CHN-PL) - Chain Operated Clutch with Plastic Chain (V) - Reverse Roll (Optional - Fabric rolls off the front of the roller tube - Away from the Glass) 20 Ch. - RTS Hand Held Transmitter (CHN-SS) - Chain Operated Clutch with Stainless Steel Chain 9. Hembar Type: (PKT) - Pocket Hembar (3-Side Welded) 1 Ch. - RTS Wireless Wall Switch (CHN-WSS) - Chain Operated Clutch w/ WHT SS Chain (EXT) - External Hembar (Alabaster, Anodized, Black, Bronze, White) 5 Ch. - RTS Wireless Wall Switch (CHN-BSS)-Chain Operated Clutch w/blk SS Chain (WH) - Wrapped Hembar (Fabric covered front, exposed aluminum on back) RS E-TRIM-1CH Transmitter Econoline (SPR) - Spring Operated 10. Valance: (3"SQR) - 3" Square Fascia (ALB, AND, BLK, BRZ, WHT) RS E-TRIM -6CH Transmitter Econoline (RS E-MOTOR-RF) Econoline Motor (4"SQR) - 4" Square Fascia (ALB, AND, BLK, BRZ, WHT) RS E-TRM-16CH Transmitter Econoline (MTR-BAT-RTS) - Somfy LT30 RTS Battery Powered Motor (3"RND) - 3" Round Fascia (AND, BLK, WHT) RTS 24 - Hour Timer (MTR-DC-RTS) - Somfy ST30 RTS DC Powered Motor (4"RND) - 4" Round Fascia (AND, BLK, WHT) RTS Sun Sensor (MTR-AC-RTS) - Somfy ST50 or LT50 RTS AC Powered Motor (3"FAB) - 3" Fabric Wrapped Fascia (AND, BLK, WHT) 16 Ch. - RTS Interface for Automation Integration (MTR-AC-HW) - Standard Hardwired 4-Wire AC Powered Motor (4"FAB) - 4" Fabric Wrapped Fascia (AND, BLK, WHT) (MRT-ILT) - Somfy ILT Intelligent Motor (PKT-NO-LIP) - Shade Pocket without Lip (AND, WHT) If Standard 4-wire motors are selected, specify the required controls. (PKT-LIP) - Shade Pocket with Lip (AND, WHT) Standard Controls: Quantity (HNGR) - Mount Hanger with Closure Plate (AND, BLK, WHT) SPDT Paddle Wall Switch 5. Spring Assist: If Chain Operated Clutch is selected, a spring assist lifting mechanism (CASSR) - Cassette Residential w/fabric insert (ANO, ALA, BLK, BRZ, WHT) DPDT Pall Wall Switch may be added to reduce the amount of pull force required to lift (CASSC) - Cassette Commercial w/fascia (ANO, ALA, BLK, BRZ, WHT) GCS II 4-Motor Controller heavier shades. (Surchargeable) (INS) - Inserted Fabric Valance IGC Single Motor Controller 6. Lift Side: (L) - Left Side Lift 11. Channels: Specify side and/or sill channels if desired. IGC3N1 3 Motor Controller (R) - Right Side Lift (Alabaster, Anodized, Black, Bronze, White) IGC Standard Wall Switch Consult Mariak Technical Support for Additional Options!

BLANK PAGE 575 West Manville Street Rancho Dominguez, CA 90220 (800) 562-7425 www.mariak.com