Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(TB)-TL5-EN TL5 Available for : ADS-AL CA Rev. Date: February 7, 05 Doc. No.: ##088## please visit www.idatalink.com for complete product details The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. 05 NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.
Page of 0 ADS-AL(TB)-TL5-EN Doc. No.: ##088## 050 install type SeLeCtiOn FeaTUres MaKe ModeL NOTE I The security light may turn ON during the remote start sequence. It will turn OFF after the takeover procedure is completed. year InsTaLL Type data IMMoBILIZer Bypass scion ToyoTa iq (80 bit) -5 tc (80 bit) -5 xb (80 bit) -5 xd (80 bit) -4 4Runner (80 bit) 0-5 Camry (80 bit) 0- Camry (80 bit) -4 Corolla (80 bit) -3 FJ Cruiser (80 bit) 0-4 Highlander (80 bit) -3 Highlander Hybrid (80 bit) -3 Matrix (80 bit) -4 Prius C (80 bit) -4 RAV4 (80 bit) - Sequoia (80 bit) -4 Sienna (80 bit) -4 Tacoma (80 bit) -4 Tundra (80 bit) -5 Venza (80 bit) 0-5 Yaris Hatchback (80 bit) Yaris Hatchback (80 bit) -4 Yaris Sedan (80 bit) -
Page 3 of 0 ADS-AL(TB)-TL5-EN Doc. No.: ##088## 050 COmPOnent LOCatOr D A B C
Page 4 of 0 ADS-AL(TB)-TL5-EN Doc. No.: ##088## 050 warning: VaLet KeyS are not COmPatiBLe 40 BIT VaLeT Key 80 BIT VaLeT Key The 40 bit valet key is GRAY and has a dot or O stamped on the metal part of the key. The 80 bit valet key is GRAY and has G stamped on the metal part of the key. This key is NOT compatible with this firmware. This key is NOT compatible with this firmware. G G Use a regular key and a compatible firmware solution. Use a regular key and a compatible firmware solution. identify regular Key 40 BIT regular Key 80 BIT regular Key The 40 bit regular key is BLACK and has a dot or O stamped on the metal part of the key. The 80 bit regular key is BLACK and has G stamped on the metal part of the key. This key is NOT compatible with this firmware. This key is compatible with this firmware. G G Use a compatible firmware solution. Proceed with installation.
Page 5 of 0 ADS-AL(TB)-TL5-EN Doc. No.: ##088## 050 type - wire CrOSS reference CHart MaKe ModeL year WIre description scion name CoLor Type position ToyoTa WIre CoLor polarity ModULe LoCaTIon CoMponenT LoCaTor iq tc xb xd 4Runner Camry Camry Corolla FJ Cruiser Highlander Hybrid Highlander Matrix Prius C RAV4 Tacoma Venza Yaris Hatchback Yaris Hatchback Yaris Sedan -5-5 -5-4 0-5 0- -4-3 0-4 -3-3 -4-4 - -4 0-5 -4 - Ignition B D8 White 08 pin 04 LtBlue (+) Ignition connector A Immobilizer ODBII White 6 pin 07 Red (DATA) ODBII B Ignition B C5 White 08 pin 04 Gray (+) Ignition connector A Immobilizer OBDII White 6 pin 07 White or Purple (DATA) OBDII B Ignition B C5 White 08 pin 04 White (+) Ignition connector A Immobilizer C4 White 6 pin 07 White (DATA) OBDII B Ignition B F9 White 08 pin 0 Green (+) Ignition connector A Immobilizer F6 White 6 pin 07 White or Blue (DATA) OBDII B Ignition B F5 White 08 pin 04 Purple (+) Ignition connector A Immobilizer F3 White 6 pin 07 Green (DATA) OBDII B Ignition B E3 White 08 pin 0 Pink (+) Ignition connector A Immobilizer E0 Black 6 pin 07 Gray (DATA) OBDII B Ignition B i36 White 08 pin 0 Pink (+) Ignition connector A Immobilizer I39 White 6 pin 07 Gray (DATA) OBDII B Ignition B E4 White 08 pin 04 Green or White (+) Ignition connector A Immobilizer E White 6 pin 07 White (DATA) OBDII B Ignition B A White 08 pin 06 Black/Red (+) Ignition connector A Immobilizer E White 6 pin 07 Red/Yellow (DATA) ODBII B Ignition B D70 White 08 pin 06 LtBlue (+) Ignition connector A Immobilizer D47 White 6 pin 07 Gray (DATA) OBDII B Ignition B D4 White 08 pin 06 LtBlue (+) Ignition connector A Immobilizer D47 White 6 pin 07 Gray (DATA) OBDII B Ignition B E5 White 08 pin 04 Green (+) Ignition connector A Immobilizer E5 White 6 pin 07 White (DATA) OBDII B Ignition B G5 White 08 pin 0 LtBlue (+) Ignition connector A Immobilizer G4 White 6 pin 07 Black (DATA) OBDII B Ignition B E3 White 08 pin 04 Pink (+) Ignition connector A Immobilizer E3 White 6 pin 07 White (DATA) OBDII B Ignition B I7 White 08 pin 06 Black/Red (+) Ignition connector A Immobilizer D4 White 6 pin 07 White (DATA) OBDII B Ignition B D White 08 pin 06 Red (+) Ignition connector A Immobilizer D White 6 pin 07 Blue (DATA) OBDII B Ignition B D8 White 08 pin 0 Green (+) Ignition connector A Immobilizer D5 White 6 pin 07 Blue or Black (DATA) OBDII B Ignition B D09 White 08 pin 0 LtBlue (+) Ignition connector A Immobilizer D0 White 6 pin 07 Black (DATA) OBDII B Ignition B D8 White 08 pin 0 Green (+) Ignition connector A Immobilizer D5 White 6 pin 07 Blue or Black (DATA) OBDII B
Page 6 of 0 ADS-AL(TB)-TL5-EN Doc. No.: ##088## 050 type - wiring diagram WARNING DO NOT CONNECT KEYSENSE. REMOTE STARTER IGNITION B (+) STANDARD (V, IGNITION, ACCESSORY, STARTER) REMOTE STARTER CONNECTIONS TO VEHICLE ARE REQUIRED V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT DATA MODE <- REQUIRED <- REQUIRED <- REQUIRED REQUIRED -> IGNITION B (+) OUTPUT LEGEND NOT REQUIRED IN DATA MODE (-WAY) NOT REQUIRED IN DATA MODE (-WAY) USE DATA MODE OR HARDWIRE MODE DATA MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND (-) - BLACK V (+) - RED (NC) GREEN/BLACK (NC) BLUE/BLACK (NC) RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) WHITE (NC) BLACK/WHITE (NC) GREEN (NC) PURPLE/WHITE WHITE/BLACK (NC) WHITE/RED (NC) WHITE (NC) YELLOW/BLACK (NC) YELLOW/RED (NC) YELLOW (NC) BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK - IMMOBILIZER DATA ORANGE/WHITE (NC) ORANGE (NC) PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) IMMOBILIZER DATA 3 4 5 6 7 8 9 0 3 4 5 6
Page 7 of 0 ADS-AL(TB)-TL5-EN Doc. No.: ##088## 050 type - wire CrOSS reference CHart MaKe ModeL year WIre description name CoLor Type position ToyoTa WIre CoLor polarity ModULe LoCaTIon CoMponenT LoCaTor Sequoia Sienna Tundra -4-4 -5 Ignition B H0 White 08 pin 0 LtGreen (+) Ignition connector B Immobilizer H9 White 6 pin 07 Tan (DATA) OBDII A SIL H40 White pin 0 Blue (DATA) TPMS module behind glove box C Ignition B D7 White 08 pin 04 Yellow (+) Ignition connector B Immobilizer D6 White 6 pin 07 White (DATA) OBDII A SIL D8 White pin 0 White (DATA) TPMS module next to driver side fuse box D Ignition B J9 White 08 pin 0 LtGreen (+) Ignition connector B Immobilizer J7 White 6 pin 07 Tan (DATA) OBDII A SIL J3 White pin 0 Blue (DATA) TPMS module behind glove box C
Page 8 of 0 ADS-AL(TB)-TL5-EN Doc. No.: ##088## 050 type - wiring diagram TPMS CONNECTOR 6 5 4 3 0 9 8 7 REMOTE STARTER SIL (DATA) IGNITION B (+) WARNING DO NOT CONNECT KEYSENSE. STANDARD (V, IGNITION, ACCESSORY, STARTER) REMOTE STARTER CONNECTIONS TO VEHICLE ARE REQUIRED V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT DATA MODE <- REQUIRED <- REQUIRED <- REQUIRED REQUIRED -> IGNITION B (+) OUTPUT LEGEND NOT REQUIRED IN DATA MODE (-WAY) NOT REQUIRED IN DATA MODE (-WAY) USE DATA MODE OR HARDWIRE MODE DATA MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND (-) - BLACK V (+) - RED (NC) GREEN/BLACK (NC) BLUE/BLACK (NC) RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) WHITE (NC) BLACK/WHITE (NC) GREEN (NC) PURPLE/WHITE WHITE/BLACK - SIL (DATA) VEHICLE SIDE WHITE/RED - SIL (DATA) CONNECTOR SIDE WHITE (NC) YELLOW/BLACK (NC) YELLOW/RED (NC) YELLOW (NC) BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK - IMMOBILIZER DATA ORANGE/WHITE (NC) ORANGE (NC) PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) IMMOBILIZER DATA 3 4 5 6 7 8 9 0 3 4 5 6
Page 9 of 0 ADS-AL(TB)-TL5-EN Doc. No.: ##088## 050 installation mode SeLeCtiOn Press and release programming button to select installation mode. LED flashes (X) once = DATA MODE LED flashes (X) twice = STANDARD HARDWIRE MODE! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. module PrOgramming PrOCedUre Insert key into ignition. 3 Wait, LED will turn solid GREEN for seconds. ON Turn key to ON position. 4 5 OFF Turn key to OFF position. Module Programming Procedure completed.
Page 0 of 0 ADS-AL(TB)-TL5-EN Doc. No.: ##088## 050 identify VeHiCLe year Locate the Vehicle Identification Number (VIN), identify the 0th character then match it to its corresponding year. Æ 4 3 A 5 Y N 5 T A L 8 D 5 R 0 X Æ a 980 L 990 y 000 a 00 B 98 M 99 00 B 0 C 98 n 99 00 C 0 d 983 p 993 3 003 d 03 e 984 r 994 4 004 e 04 F 985 s 995 5 005 F 05 G 986 T 996 6 006 G 06 H 987 V 997 7 007 H 07 J 988 W 998 8 008 J 08 K 989 X 999 9 009 K 09 Led status Flashing RED diagnostics during programming during remote start WITH IGnITIon off Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming module diagnostics Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FaCtOry reset PrOCedUre DISCONNECT all connectors from module EXCEPT the black 4-PIN standard or optional data connector. DISCONNECT black 4-PIN standard or optional data connector. 5 6 LED will turn solid red for seconds. RESET COMPLETED. RECONNECT all connectors. 3 PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data connector. 7! Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 4 When LED flashes red, RELEASE programming button. this product is protected by one or more of the following patents: U.S. LetterS Patent no. 5,79,55; 6,0,460; 6,43,004; 6,49,6; 6,75,47; 6,97,73; 6,346,876; 6,39,534; 6,59,4; 6,696,97; 6,756,885; 6,756,886; 6,77,67; 6,8,89; 6,94,750; 7,00,40; 7,03,86; 7,046,6; 7,06,37; 7,068,53; 7,05,830; 7,05,679; 7,4,083; 7,369,936; 7,378,945; 7,489,33; 7,50,937; Canadian Patent no.,30,48;,45,03;,46,670;,44,99;,45,0;,45,07;,45,038;,45,04;,50,893;,45,490;,45,96;,45,487; european Patent no.,053,8; de 69807-94T; U.S. 00045535; 006098; 0060984; 00400784; 008003036; 009007955; ep500565; 538038; 538037;