500 Series Non-Hold Open Door Closer Instructions vailable in Sizes,, and 5 Regular rm See Page n incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These installation instructions should be followed to avoid the possibility of misapplication or misadjustment. Regular rm See Page Left Hand Door - LH Right Hand Reverse - RHR Parallel rm See Pages & Left Hand Door - LH Right Hand Reverse - RHR NOTE: For special applications, a separate door and frame preparation template is packed with these instructions. Use this instruction sheet for installation sequence and closer adjustments only. Dimensions are based on standard doors and frames with /8" clearance, 5/8" stops, and square edge doors. Door and frame must be properly reinforced. Right Hand Door - RH Left Hand Reverse - LHR Parallel rm See Pages & Right Hand Door - RH Left Hand Reverse - LHR Non-Handed Door Closers. See Page 5 Left Hand Door - LH Right Hand Reverse - RHR NOTE: For pplication longer connecting rod is required for reveals greater than " (76mm) Reveal See Page 5 Right Hand Door - RH Left Hand Reverse - LHR These door closers should NOT be installed on the exposed side (weather side) of exterior doors. TOOLS REQUIRED METL WOOD Self Drilling Screws Wood and Metal Sleeve Nut and olt For wood, drill /6" hole Drill 9/" thru from Closer Side /8" Drill other Side #7 /"- 0 /6" Machine Screws #7 Drill, /"- 0 Tap Check building and fire codes to see if your application requires the use of sleeve nuts and bolts. COMPONENT PRTS LTCH VLVE MIN RM REGULR RM/TOP JM SHOE SCREW PCK SWEEP VLVE PRLLEL RM RCKET FORERM SCREW CLOSER RM PINION CP HGER COMPNIES 9 Victor Street, St. Louis, MO 60 (800) 5-9995 Fax (800) 78-09
500 Series Non-Hold Open Door Closer - Regular rm Instructions. PRTS. MRK ND DRILL HOLES (Right Hand Shown) -/8" (9mm) /" (9mm) 9-/6" (0 mm) Speed regulating valves toward hinge edge. -/" (mm) -/8" (9mm) For Opening to 0 For Opening to 80 5-/" (0mm) " (05mm) -/6" (0mm) 0-9/6" (68mm) Dimensions apply to "all sizes". Select hand of door and degree of door opening. Fold template on the corresponding line for desired degree of door opening and hand. Match this line with the hinge edge and door and attach template to door. e sure frame line on template lines up with the bottom edge of frame face. Mark, prep and drill/tap /" - 0 holes for closer body and jamb shoe mounting screws.. INSTLL CLOSER. INSTLL MIN RM 5. INSTLL MIN RM ND FRME RIGHT HND DOOR 90 RIGHT NGLE Remove template and use mounting screws to install the closer body to the door and the jamb shoe to the frame. Closer body should be oriented so that the speed regulating valves are toward the hinge stile of door. Orient main arm so that the, located on the main arm, is on the same side of the closer as the speed regulating valves. The main arm will point out away from the door. Screw connecting rod into forearm of main arm. Rotate main arm until connecting rod is at a 90 angle to frame. While holding arm in this position, tighten down forearm screw. 6. DJUSTMENTS 7. INSTLL PINION CP See djustments on Page 6 for setting Sweep Speed and Latch Speed. Press pinion cap onto un-used closer body spindle. NOTE: Do not fully unscrew valves or hydraulic fluid will leak and closer will no longer be functional. PINION CP HGER COMPNIES 9 Victor Street, St. Louis, MO 60 (800) 5-9995 Fax (800) 78-09
500 Series Non-Hold Open Door Closer - Parallel rm Instructions. PRTS. MRK ND DRILL HOLES (Right Hand Shown) 7/6" (mm) -/" (70mm) " (5mm) /8" (0mm) /" (mm) Select hand of door and the degree of door opening. Fold template on the corresponding line for desired degree and hand. Fold or cut upper corner illustrated on template and align template with the hinge edge of door. t the Frame Stop Line fold toward you and attach template to door. Mark, prep and drill/tap /"-0 holes for closer body and parallel arm bracket mounting screws. (Center on Hinge) For Opening to 0 For Opening to 80 7-5/6" (0mm) 9-/6" (0mm) 6-9/6" (67mm) 7-/6" (95mm) Dimensions apply to "all sizes". Top of Door /" (9mm) " (76mm) 9-/6" (0 mm) (Center on Hinge) Speed regulating valves toward lock stile. Frame. INSTLL CLOSER. INSTLL Remove template and use mounting screws to install the closer body to the door and the parallel arm bracket to the frame soffit. Closer body should be oriented so that the speed regulating valves are toward the lock stile of door. 5. INSTLL MIN RM For parallel arm application only, remove regular arm / top jamb shoe. ttach connecting rod to the parallel arm plate. Rotate 5 Use adjustable wrench to rotate spindle 5 counterclockwise for Right Hand Door (RH) or clockwise for Left Hand Door (LH). Place main arm on spindle so that the (RH) or (LH), located on the main arm, is adjacent to the door. Secure main arm and spindle by tightening spindle bolt. HGER COMPNIES 9 Victor Street, St. Louis, MO 60 (800) 5-9995 Fax (800) 78-09
500 Series Non-Hold Open Door Closer - Parallel rm Instructions 6. INSTLL MIN RM ND a) -/" (8mm) Screw connecting rod into forearm of main arm until pivot point is -/" from door surface. b) -/" (8mm) While holding arm in this position, tighten down forearm screw. 7. DJUSTMENTS 8. INSTLL PINION CP See djustments on Page 6 for setting Sweep Speed and Latch Speed. NOTE: Do not fully unscrew valves or hydraulic fluid will leak and closer will no longer be functional. Press pinion cap onto un-used closer body spindle. PINION CP HGER COMPNIES 9 Victor Street, St. Louis, MO 60 (800) 5-9995 Fax (800) 78-09
500 Series Non-Hold Open Door Closer - rm Instructions. PRTS. MRK ND DRILL HOLES (Right Hand Shown) -/" (mm) 9-/6" (0 mm) -/" (mm) /" (9mm) /" (mm) Speed regulating valves toward hinge edge. Top of Frame For Opening to 0 For Opening to 80 5-5/8" (mm) -/8" (08mm) -7/6" (87mm) 9-5/6" (5mm) Dimensions apply to "all sizes". longer connecting rod is required for reveals greater than " (76mm) Reveal Select hand of door and the degree of door opening. Separate template sections and. Fold template on the corresponding line for desired degree and hand. Match this line with the hinge edge of door and attach template to door. e sure Frame line on template lines up with the top edge of door. Using a square, project Closer Projection Line on section of template onto frame and use to align and attach section. e sure to align bottom edge of section with edge of frame. Mark, prep and drill/tap /"- 0 holes for connecting rod shoe and closer body mounting screws.. INSTLL CLOSER. INSTLL MIN RM 5. INSTLL MIN RM ND RIGHT HND DOOR MIN RM 90 RIGHT NGLE CONNECTING ROD FRME Remove template and use mounting screws to install the closer body to the top jamb and the connecting rod shoe to the door. Closer body should be oriented so that the speed regulating valves are toward the hinge stile of door. MIN RM Orient main arm so that the, located on the main arm, is on the same side of the closer as the speed regulating valves. The main arm will point out away from the door. POSITION OF MIN RM WHEN SSEMLING TO SPINDLE Screw connecting rod into forearm of main arm. Rotate main arm until connecting rod is at a 90 angle to frame. While holding arm in this position, tighten down forearm screw. 6. DJUSTMENTS 7. INSTLL PINION CP PINION CP See djustments on Page 6 for setting Sweep Speed and Latch Speed. Press pinion cap onto un-used closer body spindle. NOTE: Do not fully unscrew valves or hydraulic fluid will leak and closer will no longer be functional. HGER COMPNIES 9 Victor Street, St. Louis, MO 60 (800) 5-9995 Fax (800) 78-09 5
500 Series Non-Hold Open Door Closer - djustments Instructions DJUSTMENTS (USE SCREWDRIVER FOR THESE DJUSTMENTS) SWEEP SPEED LTCH SPEED OPTIONL CKCHECK C Note: djust closing time speed to between and 7 seconds from 90 to 0. Greater closing times may be required for elderly or handicapped. SPRING POWER DJUST TLE OF SIZES Closer is available in sizes,, and 5. The chart on the right shows the recommended door and closer size. djust latch speed so door completely closes and latches. Regular rm & Parallel rm Exterior (and Vestibule) Door Width Minimum Door Width (") " - 0" - 6" - " (60mm) (76mm) (9mm) (067mm) Size Size Size 5 Size Size 5 djust backcheck accordingly to prevent excessive opening speed. Interior Door Width Minimum Door Width (") " - 0" - " - 8" - 8" - 5" (60mm) (76mm) (865mm) (965mm) (9mm) (7mm) Regular rm & Parallel rm Size Size Size Size 5 Size Size Size Size 5 DJUSTMENT DIGRM RM PLCEMENT IN SHOE 7-/% Stronger or or 7-/% Weaker HGER COMPNIES 9 Victor Street, St. Louis, MO 60 (800) 5-9995 Fax (800) 78-09 6