83-300 Function of residual engine heat utilization system Operation No. of Operation Texts and Work Units, Standard Texts and Flat Rates: F10 Auxiliary fuse holder, residual engine heat utilization system M2 Blower motor M13 Circulation pump N11/6 Automatic heater control time-limit relay S25/12 60 C temperature switch, residual engine heat utilization system up to 05/93 X64/2 Intermediate connector, blower regulator, residual engine heat utilization system (vehicles with automatic climate control only) X93 Terminal block, Tempmatic/residual engine heat utilization (1-pole) P83.25-0316-59 Copyright Daimler AG 6/1/12 G/06/08. This WIS printout will not be recorded by the update service. Page 1
N11/4 Residual engine heat utilization time-limit relay up to 11/93 S46/3 Pushbutton switch X4 Terminal block, terminal 30, fuse and relay box X76/1 Connector, air volume switch/3x residual engine heat utilizaltion system, 1-pole (only in vehicles with automatic heating system or Tempmatic climate control system) A up to 11/93 B as of 12/93 P83.25-0312-59 Copyright Daimler AG 6/1/12 G/06/08. This WIS printout will not be recorded by the update service. Page 2
After switching off a warm engine, the residual engine heat utilization system may be operated in conjunction with the vehicle's heater. It serves to heat the passenger compartment by exploiting the residual thermal energy contained in the coolant. The system is operational with the key in the steering lock at position 0 or 1, or with the key withdrawn. The coolant temperature must be higher than 60 C. The heating duration of the system depends on the set temperature. The higher the set temperature, the shorter the heating duration. Before switching on the residual engine heat utilization system, the settings of the heater and ventilation should be noted: Move the air volume switch to blower stage "I". A higher blower stage heats the passenger compartment better, but puts more strain on the battery. Set the temperature selectors of the vehicle heater to the desired passenger compartment temperature. The in-car temperature automatically remains at the set level, e.g. 22 C In vehicles with automatic climate control, one of the keys of the automatic climate control must be pressed (except key ). Pressing the key is not recommended as the existing residual thermal energy is used up more quickly. Switching on: Press the switch; the lamp in the switch lights up. Switching off: turning the ignition key to position 2 automatically after approx. 15 minutes Copyright Daimler AG 6/1/12 G/06/08. This WIS printout will not be recorded by the update service. Page 3
automatically when the coolant temperature drops below approx. 60 C with the switch Copyright Daimler AG 6/1/12 G/06/08. This WIS printout will not be recorded by the update service. Page 4
83-320 Checking function of residual engine heat utilization system Operation No. of Operation Texts and Work Units, Standard Texts and Flat Rates: A. Up to 11/93 B. As of 12/93 Expose residual engine heat utilization system timer relay (N11/4). Open cover of connector (do not disconnect wiring harness). Commercially available tools and test instruments, MB test instruments (see Workshop Equipment Manual) P83.25-0331-57 Designation Multimeter e. g., order no. Sun, DMM5 Copyright Daimler AG 6/1/12 G/06/08. This WIS printout will not be recorded by the update service. Page 1
Requirements for the test Battery voltage: 11-14 V Connect voltmeter to contacts of opened connector. P83-6305-13 Copyright Daimler AG 6/1/12 G/06/08. This WIS printout will not be recorded by the update service. Page 2
83-330 Removal, reinstallation of residual engine heat utilization system timer relay (N11/4) Operation No. of Operation Texts and Work Units, Standard Texts and Flat Rates: A. Up to 11/93 Front right foot mat Foot support Connector of wiring harness at control unit N11/4 Control unit N11/4 Install Function test take out. remove. disconnect. unscrew from foot support. in the reverse sequence. at coolant temperature > 60 C. P83-6304-53 B. As of 12/93 P83.30-0421-53 Paneling on A-pillar in right front footwell remove. Control module (N11/4) remove, 1 screw. Connector on wiring harness on control module disconnect. Copyright Daimler AG 6/1/12 G/06/08. This WIS printout will not be recorded by the update service. Page 1
Reinstall Function check in opposite order. perform before installing. Copyright Daimler AG 6/1/12 G/06/08. This WIS printout will not be recorded by the update service. Page 2