05
SPECIFICATION MODEL OUTPUT INPUT RATED CURRENT RATED POWER CONSTANT CURRENT REGION OPEN CIRCUIT VOLTAGE(max.) CURRENT ADJ. RANGE CURRENT RIPPLE CURRENT TOLERANCE SET UP TIME VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR Note.4 TOTAL HARMONIC DISTORTION EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) MAX. No. of PSUs on 16A CIRCUIT BREAKER LEAKAGE CURRENT Note.2 Note.3 HBG--1050 HBG--10 HBG--2 1050mA 10mA 2mA 57.75W.2W.9W 37 ~ 55V 28 ~ 43V 19 ~ 29V V 50V 35V 6 ~ 1050mA 910 ~ 10mA 13mA ~ 2mA 20% max. @rated current ±5.0% 500ms / 230VAC 1200ms / 115VAC 90 ~ 295VAC 127 ~ 417VDC (Please refer to "STATIC CHARACTERISTIC" section) 47 ~ 63Hz PF>0.97/115VAC, PF>0.95/230VAC, PF>0.9/277VAC@ full load (Please refer to " POWER FACTOR (PF) CHARACTERISTIC" section) THD< 20%(@load 65%/115VC,230VAC; @load 75%/277VAC) (Please refer to TOTAL HARMONIC DISTORTION(THD) section) 90% 89% 89% 0.7A/115VAC 0.4A/230VAC 0.3A/277VAC COLD START 45A(twidth= μ s measured at 50% Ipeak) at 230VAC; Per NEMA 410 28 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC <0.75mA / 277VAC PROTECTION OVER CURRENT Hiccup mode, recovers automatically after fault condition is removed OVER TEMPERATURE Shut down o/p voltage, re-power on to recover WORKING TEMP. Tcase=- ~ +85 (Please refer to OUTPUT LOAD vs TEMPERATURE section) MAX. CASE TEMP. Tcase=+85 ENVIRONMENT WORKING HUMIDITY 20 ~ 95% RH non-condensing STORAGE TEMP., HUMIDITY - ~ +, 10 ~ 95% RH TEMP. COEFFICIENT VIBRATION ± 0.03%/ (0 ~ ) 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes SAFETY STANDARDS UL8750, CSA C22.2 No. 250.13-12, ENEC EN61347-1,EN61347-2-13 independent, EN62384; GB19510.14, GB19510.1, EAC TP TC 004 approved WITHSTAND VOLTAGE I/P-O/P:3.75KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P:M Ohms / 500VDC / 25 / 70% RH EMC EMC EMISSION Note. 8 Compliance to EN55015, GB17743, GB17625.1, EN-3-2 Class C (@load 65%) ; EN-3-3, EAC TP TC 020 EMC IMMUNITY Compliance to EN-4-2,3,4,5,6,8,11; EN61547, EN55024, light industry level( surge immunity:line-line:2kv), EAC TP TC 020 MTBF 1504.1K hrs min. Telcordia SR-332 (Bellcore) ; 452Khrs min. MIL-HDBK-217F (25 ) OTHERS DIMENSION ψ110mm *.5mm (D * H) PACKING 0.5Kg; 20pcs/ 11Kg/ 0.94CUFT NOTE
BLOCK DIAGRAM fosc : 50KHz I/P EMI FILTER & RECTIFIERS POWER SWITCHING RECTIFIERS & FILTER V+ V- O.L.P. PWM & PFC CONTROL DRIVING METHODS OF LED MODULE This series works in constant current mode to directly drive the LEDs. Vo(%) 65 (min.) Hiccup Protection Constant Current area In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WELL. 50 Io(%) Typical output current normalized by rated current (%)
OUTPUT LOAD vs TEMPERATURE 65 LOAD (%) 20 LOAD (%) 20 - -30-25 0 15 30 50 70 (HORIZONTAL) - -20 0 10 30 50 70 85 90 (HORIZONTAL) AMBIENT TEMPERATURE,Ta ( ) Tcase ( ) STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC Tcase at 75 90 1 0.95 0.9 0.85 LOAD (%) 70 50 PF 0.8 0.75 0.7 0.65 0.6 0.55 277V 230V 115V 90 125 135 145 155 165 175 1 200 230 295 0.5 50% % 70% % 90% % (W) INPUT VOLTAGE (V) Hz LOAD De-rating is needed under low input voltage. TOTAL HARMONIC DISTORTION (THD) 1050mA Model, Tcase at 75 EFFICIENCY vs LOAD possess superior working efficiency that up to 90% can be reached in field applications. 1050mA Model, Tcase at 75 91 25% 90 THD 20% 15% 10% 5% 277VAC 230VAC 115VAC EFFICIENCY(%) 89 88 87 86 277V 230V 115V 0% 85 50% % 70% % 90% % 84 50% % 70% % 90% % LOAD LOAD
LIFE TIME 120 LIFETIME(Kh) 20 0 25 30 35 45 50 55 65 70 75 85 Tc a s e ( )
MECHANICAL SPECIFICATION Case No.HBG- Unit:mm 98 57.5 47.5 4 3 98 11.2 ACL(Brown) ACN(Blue) 30 300 SJTW 18AWG*2C 200 SVT 18AWG*2C 30 V+(Red) V-(Black) 7.56 15 29.64 ψ 79. 27.36 tc 50 30 ψ108 ψ110 4-ψ5.28 tc : Max. Case Temperature ψ8.36 Caution Please inspect the appearance of the driver if the package is damaged. There should not be any cracks. Please do not drop or bump the driver. All screws including the suspension screw should be paired with a spring washer and locked tight. The entire luminaire, including the driver, should be limited to 5Kg or less. The luminaire should be cautiously protected from damage due to shock throughout packaging and transportation. Please thoroughly follow the preceding cautionary notes to prevent the luminaire from falling, leading to injuries.