Digital Inverter Air Conditioner Application Control Kit INSTALLATION MANUAL CAUTIONS for SAFETY CAUTION Use for Outdoor Unit Only Model:TCB-PCOSE For Installation Professionals Please read this manual thoroughly before starting the installation work, and install the products correctly. WARNING Ask an authorized dealer or qualified installation professional to install/maintain the air conditioner. Inappropriate installation may result in electric shock or fire. Perform installation work surely based on this Installation Manual. Incomplete installation causes an electric shock or a fire. Ask an authorized dealer or qualified installation professional to reinstall adapters. Incomplete installation causes an electric shock or a fire. For an electric work, this Installation Manual shall be referred and exclusive circuit shall be necessarily used. The used voltage shall be also match with the rated voltage of the product. If there is capacity shortage of electric circuit or installation work is poor, an electric shock or a fire may be caused. Using the specified wires, surely connect wires so that external force of wire is not applied to connecting part of the terminals; otherwise disconnection, heating or fire will generate. For wiring work, use wires with correct current capacity; otherwise earth leakage, heating or fire will generate. Do not apply an excessive force on the board body, otherwise bending, separation, or disconnection generates resulted heating or fire. After installation work, execute a test run to confirm there is no trouble. And also ask the customers to keep this Manual by themselves.. Object model RAV-SMAT-E, SM80AT-E RAV-SM0AT-E, SM0AT-E
. Accessories Name Wire(A) (Yellow connector : -core) Wire(B) (Blue connector : -core) (Red connector : -core) (Blue connector : -core) Fixing plate(a) Fixing plate(b) Spacer Screws(A) (M x ) Screws(B) (M x 8 ) Binding band Holder Installation Manual Q'ty Application Connecting wire for Night operation(sound reduction) control or Power peak-cut control Connecting wire for Compressor operation output Application control Connecting wire for Power supply Connecting wire for Communication line Fixing plate(sm,80) For fixing plate(a) Fixing plate(sm0,0) For fixing Application Control For fixing plate(b) For fixing Fixing screws for mounting fixing plate and cover Used to process wires for binding the wires This Manual Use Power peak-cut control Night operation (Sound reduction) Compressor operation output Correspond to the temporary power peak-cut control by controlling the capacity of the outdoor unit using an external signal. Capacity control is made in steps of 7%, 0% and Operation stop. The capacity is controlled using a timer procured on site (to be purchased locally) regardless of the outdoor temperature and load to reduce the sound level of the operation. Outputs a dry contact ON signal when the compressor is in operation.. How to install No. 7 8 9 0 Wire(A) Wire(B) Name Fixing plate(a) Fixing plate(b) Spacer Screws(A) Screws(B) Binding band Holder Installation manual Q'ty RAV-SM,80 Q'ty to be used RAV-SM0,0 Work items Connect a timer (local procurement) to the CN00 of Connect a timer (local procurement) to the CN0 of Connect between the CN00 of the and faston receptacle of terminal block for power supply of the outdoor unit. Connect between the CN00 of the and the of the outdoor unit. (SM,SM80 : CN80 SM0,SM0 : CN80) Connect to the CN0 and CN0 of For attaching For fixing Wire clamp For fixing For fixing plate(a),, and fixing plate(b) Used suitably
<RAV-SM, SM80> 0 ( only) ( wire) ( wire) 7 8 <RAV-SM0, SM0> ( wire) ( wire) ( only) 9 0
. Wiring diagram Faston receptacle of terminal block for power supply of the outdoor unit CN0 CN00 CN0 CN00 CN0 CN00 An Outdoor unit is controlled as follows by connecting between a white and each line using Timer or Switch purchased locally. Local Supply White White Black Yellow Orange Red Caution Don't connect two or more contacts of power peak-cut with white line at the same time. Black Yellow Orange Red Common Night operation (Sound reduction by db at cooling mode) Power peak-cut 0% operation (stop) Power peak-cut 0% operation Power peak-cut 7% operation Compressor operation output Non-voltage ON/OFF ( output signal (Dry contact) ) (to be purchased locally) DC0V, 0mA to A DCV, 0mA to A DCV, 0mA to A Inverter assembly of the outdoor unit SM,80 : CN80 SM0,0 : CN80. Parts installation method and assembly to the outdoor unit (SM, SM80) Installation method for the of the outdoor unit Fixing plate(a) () Mount a to the rear side of the Fixing plate(a) using Screws(A) ( pieces). () Install Spacers ( pieces) and to the front side of the Fixing plate(a). () Connect the Lead wires ( types) of the to the CN0 and CN0 of the. In addition, connect the (-core) to CN00 and the (-core) to CN00. To connect the Wire(A) and the Wire(B), refer to the Wiring diagram of installation method to connect the wires. Lead wires of the (connected to the CN0) Wire(B) (connected to the CN0) (connected to the CN00) Wire(A) (connected to the CN00) Screws(A) ( pieces) Extract the wires other than the wire(d) from this cut-away section Screws(B) ( pieces) (connected to the CN00) Lead wires of the (connected to the CN0) Spacer ( pieces) Extract the wire(d) from this cut-away section CAUTION Don't allow the wires to come into pinching with cover parts. Otherwise, the wires may be broken or heated or fire may occur. () Close the cover to the Fixing plate(a) with Screws(B) ( pieces). Pass the wires through the cut-away section of the cover and do not allow the wires to come into pinching.
Assembly to the Outdoor Unit Screws(B) ( pieces) () Remove the Top plate. () Remove the Front cabinet. () Remove the of packed valve and wiring lid. () Fix the assembly to the Inverter assembly with Screws(B) ( pieces). () Remove the power supply terminal block cover of the outdoor unit and connect the (-core) to the faston receptacle of terminal block for power supply. () Connect the (-core) to the Inverter assembly. Connect the wire to CN80. connect to the CN80 Application Control Kit (7) Tie the wire with binding band, if necessary. (8) Re-assemble the Front cabinet. Connect the (-core) to the faston receptacle of the terminal block for power supply.. Parts installation method and assembly to the outdoor unit (SM0, SM0) Installation method for the of the outdoor unit () Fix the clamp to the Fixing plate(b). () Fix the Spacers( pieces) and to the front side of the Fixing plate(b). () Mount the to the Fixing plate(b). () Connect the (-core) to CN00. Pass the wires through the section of the Fixing plate(b) and do not allow the wires to come into pinching. CAUTION Don't allow the wires to come into pinching with cover parts. Otherwise, the wires may be broken or heated or fire may occur. (connected to the CN00) Lead wires of the (connected to the CN0) Wire(A) (connected to the CN00) Wire(B) (connected to the CN0) (Extract the wires other than the wire(d) from this clamp section) (connected to the CN00) (Extract the wire(d) from this clamp section) Fixing plate(b) Lead wires of the (connected to the CN0) To connect the Wire(A) and the Wire(B), refer to the Wiring diagram of installation method to connect the wires. Spacer ( pieces)
Assembly to the Outdoor Unit () Remove the Front cabinet. () Fix the Application Control Kit to the Inverter assembly with Screws(B) ( pieces). Install the Application Control Kit in the back of Inverter assembly. Application Control Kit Screws(B) ( pieces) () Connect the Wire (D) (-core) to CN80 of the SUB. SUB Connect the (-core) to the faston receptacle of the terminal block for power supply. Holder ( pieces) connect to the CN80 () Tie the wire with binding band, if necessary. () Re-assemble the Front cabinet.
EH9980-()