9 YEARS: 0-PRESENT Safety glasses should be worn at all times while installing this product. INSTALLATION INSTRUCTIONS MAKE: HONDA MODEL: CR-V STYLE: SUV WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY For more information log onto www.curtmfg.com & for helpful towing tips log onto www.hitchinfo.com WEIGHT CARRYING: PRO INSTALL TIME: NOVICE INSTALL TIME: TRAILER WEIGHT: TONGUE WEIGHT: 0 MIN. 0 MIN. IF YOU ARE HESITANT TO UNDERTAKE THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED CURT INSTALLER FOR ADDITIONAL ASSISTANCE. INSTALLATION REQUIRES: /" /" RATCHET SOCKET " SOCKET EXTENSION,00 LBS. LBS. INSTALLATION TIPS: VEHICLE PHOTO:. BEFORE YOU BEGIN INSTALLATION, READ ALL INSTRUCTIONS THOROUGHLY.. TO EASE INSTALLATION, PEOPLE MAY BE REQUIRED.. USING PROPER TOOLS WILL GREATLY IMPROVE THE QUALITY OF THE INSTALL AND REDUCE THE TIME REQUIRED.. NEED HELP OR HAVE SOME QUESTIONS? CALL TECHNICAL SUPPORT AT 800.98.08 LEVEL OF DIFFICULTY: EASY MODERATE EASY CHALLENGING LOWER EXHAUST REPRESENTATIVE PHOTO HITCH ILLUSTRATION: TORQUE WRENCH MASKING TAPE AVIATION SHEARS FISHWIRE HARDWARE REQUIRED FASCIA & BRACKET TRIM REQUIRED SCREW DRIVER PRY BAR ELECTRICAL TAPE SAFETY GLASSES MAKE SURE YOUR HITCH MATCHES PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND SCAN FOR MORE INFO CURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, CURT Manufacturing LLC. may repair or replace the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage. For more information log onto www.curtmfg.com This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V- and SAE J8. //08
INSTALLATION WALKTHROUGH:. Lower exhaust by removing () rubber isolators from the exhaust towards the rear of the vehicle. Remove () fasteners from lower fascia. Parts List ITEM QTY PART NUMBER DESCRIPTION /- x / CARRIAGE BOLT CM-SP.0 x.88 x." SQUARE HOLE SPACER /- HEX FLANGE NUT /" FISHWIRE / - x " CARRIAGE BOLT CM-SP.0 x.0 x.00" ROUND HOLE SPACER / - " HEX FLANGE NUT PASSENGER SIDE DRIVER SIDE A ACCESS HOLES RECOVERY. Fishwire () /" carriage bolts and () CM-SP spacers through the vehicle access holes to the attachment holes on each side. See FISHWIRE DIAGRAM below. TOW PLATE DETAIL A For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
INSTALLATION WALKTHROUGH:. Trim lower fascia as shown in FASCIA TRIM DIAGRAM below. CAUTION: Be aware of electrical components when trimming. NOTE: Trimming of underbody panel may ease installation. FASCIA TRIM DIAGRAM UNDERBODY PANEL. in.000 in. in. in TRIM DIAGRAM. Raise hitch into position feeding the fishwires through the holes in the hitch. Once hitch is in place, remove the fishwires and loosely secure () /" hex flange nuts on each side. Secure Tow Loop Plate to recovery loop using () /" bolt, () CM-SP spacer and () /" hex flange nut. For more information log onto www.curtmfg.com. Torque all /" hardware to 9 ft-lbs and all /" hardware to 0 ft-lbs. Reinstall items removed in Steps.
9 //08 HONDA CR-V GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH:,00 LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT. WARNING: *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY *** FOR MORE INFORMATION LOG ONTO WWW.CURTMFG.COM HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT -800-98-08 Parts List ITEM QTY PART NUMBER DESCRIPTION /- x / CARRIAGE BOLT CM-SP.0 x.88 x." SQUARE HOLE SPACER /- HEX FLANGE NUT /" FISHWIRE / - x " CARRIAGE BOLT CM-SP.0 x.0 x.00" ROUND HOLE SPACER _ - HEX FLANGE NUT PASSENGER SIDE RECOVERY TOW PLATE ACCESS HOLE DRIVER SIDE ACCESS HOLE A DETAIL A TOOLS REQUIRED RATCHET /", /" SOCKETS " SOCKET EXTENSION TORQUE WRENCH MASKING TAPE AVIATION SHEARS SCREW DRIVER PRY BAR ELECTRICAL TAPE SAFETY GLASSES HITCH WEIGHT: 0 LBS. INSTALL TIME PROFESSIONAL: 0 MINUTES NOVICE (DIY): 0 MINUTES INSTALL NOTES: - LOWER EXHAUST - FISHWIRE HARDWARE REQUIRED - FASCIA TRIM REQUIRED INSTALLATION STEPS. in. in. Lower exhaust by removing () rubber isolators from the exhaust towards the rear of the vehicle. Remove () clips from lower fascia.. Fishwire () /" carriage bolts and () CM-SP spacers through the vehicle access hole to the attachment holes on each side. (See fishwire diagram). Trim lower fascia as shown in FASCIA TRIM DIAGRAM. CAUTION: Be aware of electrical components when trimming. NOTE: Trimming underbody panel may ease installation.. Raise hitch into position feeding the fishwires through the holes in the hitch. Once hitch is in place, remove the fishwires and loosely secure () /" hex flange nuts on each side. Secure Tow Loop Plate to recovery loop using () /" bolt, () CM-SP spacer, and () /" hex flange nut.. Torque all /" hardware to 9 ft-lbs and all /" hardware to 0 ft-lbs. Reinstall items removed in Step. PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND..000 in FASCIA TRIM DIAGRAM CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. Scan If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, for more with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to information repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V- and SAE J8.