PRODUCT GUIDE ORBIT5A DOCUMENT NUMBER REVISION DATE 2060728 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work.
GETTING STARTED PAGE 2 OF 2 2060728 WELCOME Congratulations on the purchase of your Orbit solution. You are now a few simple steps away from enjoying your new remote starter unit with enhanced features. Before starting your installation, please ensure that your Orbit module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. TABLE OF CONTENTS Box Contents 3 Tach Programming Procedure 4 Remote Programming Procedure 5 Valet Mode Programming Procedure 6 Compatible Accessories 7 Online Module Settings 9 Module Diagnostics 0 Remote Starter Error Codes Module Reset Procedure 2 NEED HELP? 866 427-2999 support@idatalink.com idatalink.com/support www.2voltdata.com/forum www.facebook.com/groups/idatatech ORBIT5A
BOX CONTENTS - OF PE 3 OF 2 2060728 B AUTOMATIC TRANSMISSION CUT LOOP M2-2 PIN BLACK M3-0 PIN WHITE TELEMATIC - 4 PIN BLUE TELEMATIC 2-4 PIN RED NC - 4 PIN RED LED RF PORT/WEBLINK PORT - 4 PIN BLACK -WAY REMOTE USB M - 8 PIN BLACK M5-6 PIN BLUE M4-20 PIN BLACK NC - 3 PIN BLACK PROGRAMMING BUTTON LED 2 ANTENNA 2 4 6 8 2 4 3 6 5 8 7 0 9 2 2 4 6 8 0 3 5 7 3 5 7 9 M 0 ORANGE - ACCESSORY (+) 02 RED - POWER (30A) 03 PURPLE - STARTER (+) 04 PINK/WHITE - PROG. RELAY #4 - IGNITION 2 (+) (DEFAULT) 05 PINK - IGNITION (+) 06 WHITE - PROG. RELAY #5 (0A) - PARKING LIGHTS (+) (DEFAULT) 07 RED - POWER (30A) 08 BLACK - GROUND M2 0 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK RELEASE (-) OUTPUT 04 GREEN/WHITE BLACK DOT - ARM (-) OUTPUT 05 GREEN/BLACK BLACK DOT - DISARM (-) OUTPUT 06 BLUE/WHITE BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE BLACK DOT - POC - 2ND UNLOCK OTHER DOORS (-) OUTPUT 09 PURPLE/BLACK BLACK DOT - POC 2 - RAP SHUTDOWN (-) OUTPUT 0 WHITE/BLACK BLACK DOT - POC 3 - HORN (-) OUTPUT BROWN/BLACK BLACK DOT - POC 4 - STARTER KILL (-) OUTPUT 2 WHITE BLACK DOT - PARKING LIGHTS (-) OUTPUT M3 0 BROWN SILVER DOT - BRAKE (+) INPUT 02 BLACK/WHITE SILVER DOT - E-BRAKE (-) INPUT 03 PURPLE SILVER DOT - DOOR (+) INPUT 04 GREEN SILVER DOT - DOOR (-) INPUT 05 PURPLE/WHITE SILVER DOT - TACH (-) INPUT 06 WHITE/BLUE SILVER DOT - X-TRIGGER (-) INPUT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT - TRUNK (-) INPUT 09 GRAY/BLACK SILVER DOT - GLOW PLUG (+) INPUT 0 EMPTY M4 2X ANTENNA LED ANTENNA BUTTON RF PORT - 4 PIN BLACK 2 4 3 6 5 8 7 0 9 2 4 3 6 5 8 7 20 9 FUNCTIONS DEFINED BY FIRMWARE STICKERS HOOD SWITCH ANTENNA CABLE 2X M5 3 5 2 4 6 FUNCTIONS DEFINED BY FIRMWARE Aomotive Data Solutions Inc. 206 ORBIT5A www.a.om
! "#$%#&&'(% "#$ )*+#), - $/ - PAGE 4 OF 2 2060728 0 OFF START 0ART vehicle for 5 seconds. S SOP 02 Press and hold the brake pedal. 03 Press and release the module s programming button. (OR if the remotes are already programmed to the vehicle, press and hold the start button of the remote for 2.5 seconds.) 04 Wait, LED 2 will flash GREEN. (See the Module Diagnostics page) 05 Release the brake pedal. 06 Module Programming Procedure completed. ORBIT5A
234563 72582944:;8 725<3=>23? @ 5C @ PAGE 5 OF 2 2060728 0 [4x] WARNING: Complete the module programming procedure and tach programming procedure before programming the remotedf G HIJKHLH MN NMLo OPJQ oemotes per system. 07 Release the antenna button. The antenna s leds will turn OFF. 02 OFF START Set ignition to ON position. 08 OFF START Set ignition to OFF position. ENGINE START STOP ENGINE START STOP 03 Press and release the antenna button, then press and hold the antenna button. The antenna s leds will turn solid BLUE. 09 Remote Programming Procedure completed. 04 05 Parking Light will flash once [x]. Press once [x] on the LOCK button of each remote. >> F To program an additional remote as second vehicle mode: Follow steps to 4. Press twice [2x] on the F button then press once [x] on the LOCK button of the remote. Follow steps 6 to 9. 06 The antenna s leds will flash BLUE once [x] for each successful pairing. ORBIT5A
VRTUV WXYU Z[X\[RWW]^\ Z[X_UY`[U b c Xd c PAGE 6 OF 2 2060728 >> fgte: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 06 Valet Mode Programming Procedure completed. 0 Time restriction. Complete next step within 7 seconds. >> To exit valet mode: repeat steps to 5. 02 OFF START Cycle ignition ON twice [2x OFF/ON] rapidly. ENGINE START STOP 03 Press and release the BRAKE pedal three times [3x]. 04 Parking Light will flash once [x] then will flash twice [2x]. 05 OFF START Set ignition to OFF position. ENGINE START STOP ORBIT5A
hijklmnpqr lhhrssitnrs u v iw x PAGE 7 OF 2 2060728 WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT 4 PIN BLACK CABLE WEBLINK MOBILE (accessory sold separately) OBDII CONNECTOR MODULE WEBLINK PORT 4 PIN BLACK CABLE MOBILE DEVICE PORT 2 3 4 5 6 7 8 OBDII CONNECTOR 9 0 2 3 4 5 6 TELEMATIC KIT (accessory sold separately) MODULE TELEMATIC BLUE PORT (NC) *For SmartStart, use the module s RED Telematic port. ORBIT5A
ˆ Š ŒŽ ˆ ˆ PAGE 8 OF 2 2060728 š œžÿ MODULE RF PORT 4 PIN BLACK CABLE ANTENNA } ƒ }z e Data Solutions Inc. 206 ORBIT5A wwwyz{ } ~z y ƒ
ONLINE MODULE SETTINGS PAGE 9 OF 2 2060728 WEB PROGRAMMABLE MENUS MENU Remote Starter MENU 2 Doorlock Options MENU 3 Security Options MENU 4 AUX function assignments MENU 5 Programmable outputs (POC) MENU 6 Pulse Timer Output Coniguration (PTO) MENU 7 Input Conigurations MENU 8 Output Conigurations Programming options are avaible through Weblink and Weblink Mobile only. DESCRIPTION RS related coniguration options Convenience feature coniguration options Alarm activation and settings Set transmitter AUX buttons controls Set actions for programmable outputs Set duration for pulse timer outputs (if used) Set inputs for Auto by irmware/data/analog Set outputs for Auto by irmware/data/analog ORBIT5A
MODULE DIAGNOSTICS - OF PAGE 0 OF 2 2060728 TEST MODULE LED STATUS DIAGNOSTIC I II III IV DURING MODULE PROGRAMMING DURING TACH PROGRAMMING DURING REMOTE START WITH IGNITION OFF Flashing RED Missing/wrong information from irmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then OFF Module correctly programmed. OFF No activity or module already programmed. GREEN flash Tach signal programmed in Analog 2 GREEN flashes Tach signal programmed in Data 3 RED flashes No tach signal detected 4 RED flashes System is in valet mode 5 RED flashes Tach set for VTS. No tach programming required 6 RED flashes Tach set for assumed start. No tach programming required Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then OFF Reset in progress. OFF Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then OFF Reset in progress. OFF Module at rest and ready for a remote start sequence. ORBIT5A
ª«TE STARTER ERROR CODES - OF PAGE OF 2 2060728 REMOTE STARTER ERROR CODES: NOTES [X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash three [3x] times, then will flash [X] number times to indicate an error code. See table. 0 ±² ³ 02 Ke µ µ ¹ º» µ ³ 03 Door is open. 04 ¼runk is open. 05 Foot brake is ON. 06 Hood is open. 07 The reservation is OFF. (Manual transmission only) 08 Tach failure. 09 The vehicle is moving (VSS). 0 System is in Valet Mode. CAN communication failure 2 RS not synchronized. Start vehicle with OEM key for 5 sec before trying a new RS sequence. 3 Bypass problem. REMOTE STARTER SHUTDOWN ERROR CODES: NOTES [Y] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. If the engine shuts down after a remote starter sequence: Press and hold the Trunk button and the Start button at the same time for 2.5 seconds when using a -WAY remote. OR Press once [x] on button 4 when using a 2-WAY remote. The parking lights will flash four [4x] times, then will flash [Y] number times to indicate an error code. See table. 0 Engine tach signal is lost. 02 Emergency brake is lost. 03 Foot brake is ON. 04 Hood is open. 05 Engine RPM limiter is ON. 06 Glow plug timeout error. 07 Vehicle is moving (VSS). 08 N/A 09 N/A 0 Door is open. CAN communication failure during RS sequence. 2 RS not synchronized. Start vehicle with OEM key for 5 sec before trying a new RS sequence. 3 Takeover is not allowed. 4 Shutdown error, board overheat protection. ORBIT5A
MODULE RESET PROCEDURE - OF PAGE 2 OF 2 2060728 >> ½¾ ÀolloÁÂÃÄ ÅÆocedur Æ Ç ÈÇ È¾ ÉÊËÌÍ ÅÆÊÄÆÎÉÉÂÃÄ ÈÊ È¾ Ï ¾ÂÐÍ Ñ ÒÈ ËÊ Ç ÃÊÈ Æ Ç È ÎÃÓ Ç ÈÈÂÃÄÇ Ðonigured online. 06 Module RESET completed. 0 Disconnect all connectors from module except the M BLACK 8-pin connector and the M4 BLACK 20-pin connector. 07 Reconnect all connectors. 02 Disconnect the M BLACK 8-pin connector and the M4 BLACK 20-pin connector. 08 Repeat programming procedure. 03 PRESS AND HOLD the module s programming button while connecting the M BLACK 8-pin connector and the M4 BLACK 20-pin connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 04 Wait, LED will flash RED. RELEASE programming button. 05 LED will turn RED for 2 seconds. ORBIT5A
INSTALL GUIDE 205-206 AUDI A3 STD KEY AT DOCUMENT NUMBER REVISION DATE FIRMWARE ORB-RSD-VW8-[ORBIT5A] HARDWARE ORBIT5A ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work.
HARDWIRE / COMPONENT LOCATOR - OF PAGE 2 OF 7 C B A T002_W ORB-RSD-VW8-[ORBIT5A]-EN 205-206 Audi A3 STD key AT
HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF 7 M! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY TWO KEYS ARE REQUIRED FOR THIS INSTALLATION. ONE KEY WILL REMAIN PERMANENTLY IN THE VEHICLE. THE OTHER KEY WILL BE USED FOR THE PROGRAMMING PROCEDURE. IT WILL THEN BE RETURNED TO THE OWNER. REMOVE BATTERY 5-6 LOOPS AROUND KEYFOB IMMOBILIZER (A) M 0 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK IMMOBILIZER (DATA) RED - 0 : BLACK 2 M2 0 GREEN BLACK DOT 02 BLUE BLACK DOT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT 2 WHITE BLACK DOT CANL (DATA) ORANGE/BROWN - 03 CANH (DATA) ORANGE/GREEN - 04 KEYSENSE (+) PURPLE/RED - 07 IGNITION 2 (+) YELLOW/GREEN - 4 IGNITION (+) BLACK/RED - 6 STARTER (+) RED/BLACK - 06 : BLACK 6 5 4 3 2 0 9 8 7 6 5 4 3 2 MODULE, BOTTOM OF STEERING COLUMN (B) M3 M4 0 BROWN SILVER DOT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 02 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW - IGNITION 2 (+) OUTPUT 0 EMPTY GRAY/RED 2 GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE - HAZARD (-) OUTPUT 5 BROWN - ACCESSORY (+) IN/OUT 6 ORANGE/BLACK 7 PINK - IGNITION (+) IN/OUT 8 PURPLE - STARTER (+) OUTPUT 9 RED - 2V (+) INPUT 20 BLACK - GROUND (-) BRAKE (+) BLACK/RED - 58 HAZARDS (+) 2V PURPLE/RED (+) RED/BLACK - 42 2V 2V (+) (+) RED/BLUE RED/BLACK - 73 : BLACK/WHITE 2 3 4 5 6 7 8 9 0 2 3 4 5 6 7 8 9 20 22 23 24 25 26 38 39 40 4 42 43 44 45 2 46 47 48 49 50 5 52 53 27 28 29 54 30 55 3 56 32 57 33 58 34 59 35 60 36 6 37 62 63 64 65 66 67 68 69 70 7 72 73 BCM (C) M5 0 GRAY/BLACK BLUE DOT 02 WHITE/BLACK BLUE DOT - IMMOBILIZER VEHICLE SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - IMMOBILIZER CONNECTOR SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT - IMMOBILIZER CONNECTOR SIDE HORN (-) HOOD SWITCH 2 T002_W INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 2 ORB-RSD-VW8-[ORBIT5A]-EN 205-206 Audi A3 STD key AT
PAGE 4 OF 7 0 OFF START Insert key into ignition. 07 Press and release the module s programming button. 02 OFF START Turn key to ON position. 08 Release the brake pedal. 03 Wait, LED will turn solid GREEN for 2 seconds. 09 Wait, LED 2 will flash GREEN. 04 OFF START Turn key to OFF position. 0 Module Programming Procedure completed. 05 OFF START START vehicle for 5 seconds. 06 Press and hold the brake pedal. ORB-RSD-VW8-[ORBIT5A]-EN 205-206 Audi A3 STD key AT
PAGE 5 OF 7 >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 0 Press unlock on aftermarket remote. 02 OFF START Insert key into ignition. 03 OFF START Turn key to ON position. 04 Press and release BRAKE pedal. 05 Take over procedure completed. ORB-RSD-VW8-[ORBIT5A]-EN 205-206 Audi A3 STD key AT
INSTALLATION CHECKLIST - OF 2 PAGE 6 OF 7 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 7 Press the AUX 2 button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. CHECKLIST - WITH AFTERMARKET KEYFOB 9 Press the START/STOP button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. 2 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 20 Installation checklist completed. ORB-RSD-VW8-[ORBIT5A]-EN 205-206 Audi A3 STD key AT
INSTALLATION CHECKLIST - 2 OF 2 PAGE 7 OF 7 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? CHECKLIST - WITH OEM KEYFOB NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 2 Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. ORB-RSD-VW8-[ORBIT5A]-EN 205-206 Audi A3 STD key AT
INSTALL GUIDE 205-206 AUDI S3 STD KEY AT DOCUMENT NUMBER REVISION DATE FIRMWARE ORB-RSD-VW8-[ORBIT5A] HARDWARE ORBIT5A ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work.
HARDWIRE / COMPONENT LOCATOR - OF PAGE 2 OF 7 C B A T002_W ORB-RSD-VW8-[ORBIT5A]-EN 205-206 Audi S3 STD key AT
HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF 7 M! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY TWO KEYS ARE REQUIRED FOR THIS INSTALLATION. ONE KEY WILL REMAIN PERMANENTLY IN THE VEHICLE. THE OTHER KEY WILL BE USED FOR THE PROGRAMMING PROCEDURE. IT WILL THEN BE RETURNED TO THE OWNER. REMOVE BATTERY 5-6 LOOPS AROUND KEYFOB IMMOBILIZER (A) M 0 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK IMMOBILIZER (DATA) RED - 0 : BLACK 2 M2 0 GREEN BLACK DOT 02 BLUE BLACK DOT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT 2 WHITE BLACK DOT CANL (DATA) ORANGE/BROWN - 03 CANH (DATA) ORANGE/GREEN - 04 KEYSENSE (+) PURPLE/RED - 07 IGNITION 2 (+) YELLOW/GREEN - 4 IGNITION (+) BLACK/RED - 6 STARTER (+) RED/BLACK - 06 : BLACK 6 5 4 3 2 0 9 8 7 6 5 4 3 2 MODULE, BOTTOM OF STEERING COLUMN (B) M3 M4 0 BROWN SILVER DOT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 02 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW - IGNITION 2 (+) OUTPUT 0 EMPTY GRAY/RED 2 GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE - HAZARD (-) OUTPUT 5 BROWN - ACCESSORY (+) IN/OUT 6 ORANGE/BLACK 7 PINK - IGNITION (+) IN/OUT 8 PURPLE - STARTER (+) OUTPUT 9 RED - 2V (+) INPUT 20 BLACK - GROUND (-) BRAKE (+) BLACK/RED - 58 HAZARDS (+) 2V PURPLE/RED (+) RED/BLACK - 42 2V 2V (+) (+) RED/BLUE RED/BLACK - 73 : BLACK/WHITE 2 3 4 5 6 7 8 9 0 2 3 4 5 6 7 8 9 20 22 23 24 25 26 38 39 40 4 42 43 44 45 2 46 47 48 49 50 5 52 53 27 28 29 54 30 55 3 56 32 57 33 58 34 59 35 60 36 6 37 62 63 64 65 66 67 68 69 70 7 72 73 BCM (C) M5 0 GRAY/BLACK BLUE DOT 02 WHITE/BLACK BLUE DOT - IMMOBILIZER VEHICLE SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - IMMOBILIZER CONNECTOR SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT - IMMOBILIZER CONNECTOR SIDE HORN (-) HOOD SWITCH 2 T002_W INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 2 ORB-RSD-VW8-[ORBIT5A]-EN 205-206 Audi S3 STD key AT
PAGE 4 OF 7 0 OFF START Insert key into ignition. 07 Press and release the module s programming button. 02 OFF START Turn key to ON position. 08 Release the brake pedal. 03 Wait, LED will turn solid GREEN for 2 seconds. 09 Wait, LED 2 will flash GREEN. 04 OFF START Turn key to OFF position. 0 Module Programming Procedure completed. 05 OFF START START vehicle for 5 seconds. 06 Press and hold the brake pedal. ORB-RSD-VW8-[ORBIT5A]-EN 205-206 Audi S3 STD key AT
PAGE 5 OF 7 >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 0 Press unlock on aftermarket remote. 02 OFF START Insert key into ignition. 03 OFF START Turn key to ON position. 04 Press and release BRAKE pedal. 05 Take over procedure completed. ORB-RSD-VW8-[ORBIT5A]-EN 205-206 Audi S3 STD key AT
INSTALLATION CHECKLIST - OF 2 PAGE 6 OF 7 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 7 Press the AUX 2 button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. CHECKLIST - WITH AFTERMARKET KEYFOB 9 Press the START/STOP button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. 2 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 20 Installation checklist completed. ORB-RSD-VW8-[ORBIT5A]-EN 205-206 Audi S3 STD key AT
INSTALLATION CHECKLIST - 2 OF 2 PAGE 7 OF 7 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? CHECKLIST - WITH OEM KEYFOB NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 2 Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. ORB-RSD-VW8-[ORBIT5A]-EN 205-206 Audi S3 STD key AT
INSTALL GUIDE 205 VOLKSWAGEN GOLF STD KEY AT DOCUMENT NUMBER REVISION DATE FIRMWARE ORB-RSD-VW8-[ORBIT5A] HARDWARE ORBIT5A ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work.
HARDWIRE / COMPONENT LOCATOR - OF PAGE 2 OF 7 E C D B A T00_W ORB-RSD-VW8-[ORBIT5A]-EN 205 Volkswagen Golf STD key AT
HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF 7 M! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY TWO KEYS ARE REQUIRED FOR THIS INSTALLATION. ONE KEY WILL REMAIN PERMANENTLY IN THE VEHICLE. THE OTHER KEY WILL BE USED FOR THE PROGRAMMING PROCEDURE. IT WILL THEN BE RETURNED TO THE OWNER. REMOVE BATTERY IMMOBILIZER (A) M 0 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK M2 0 GREEN BLACK DOT 02 BLUE BLACK DOT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT 2 WHITE BLACK DOT M3 0 BROWN SILVER DOT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY M4 M5 0 EMPTY 02 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW - IGNITION 2 (+) OUTPUT 0 EMPTY GRAY/RED 2 GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE 5 BROWN - ACCESSORY (+) IN/OUT 6 ORANGE/BLACK 7 PINK - IGNITION (+) IN/OUT 8 PURPLE - STARTER (+) OUTPUT 9 RED - 2V (+) INPUT 20 BLACK - GROUND (-) 0 GRAY/BLACK BLUE DOT - 2V (+) VEHICLE SIDE 02 WHITE/BLACK BLUE DOT - IMMOBILIZER VEHICLE SIDE 03 GRAY/RED BLUE DOT - 2V (+) CONNECTOR SIDE 04 WHITE/RED BLUE DOT - IMMOBILIZER CONNECTOR SIDE 05 GRAY BLUE DOT - PARKING LIGHT (+) 06 WHITE BLUE DOT - IMMOBILIZER CONNECTOR SIDE 5-6 LOOPS AROUND KEYFOB IMMOBILIZER (DATA) BLUE - 0 CANL (DATA) ORANGE/BROWN - 03 CANH (DATA) ORANGE/GREEN - 04 KEYSENSE (+) PURPLE/RED - 07 IGNITION 2 (+) BLACK/GREEN OR BLACK/GRAY - 4 IGNITION (+) BLACK/WHITE OR BLACK - 6 STARTER (+) RED/BLACK OR BLACK/RED - 06 BRAKE (+) BLACK/RED - 58 2V (+) 2V RED/YELLOW (+) RED/BLACK - 6 PARKING LIGHT (+) GRAY/YELLOW - 03 2V 2V (+) RED/WHITE (+) RED/BLACK - 08 HORN (-) HOOD SWITCH 2 : BLACK 2 : BLACK 6 5 4 3 2 0 9 8 7 6 5 4 3 2 : BLACK/WHITE 2 3 4 5 6 7 8 9 0 2 2 3 4 5 6 7 8 9 0 2 3 4 5 6 : RED 3 4 5 6 7 8 9 20 22 23 24 25 26 38 39 40 42 43 44 45 2 46 47 48 49 50 27 28 29 54 30 55 3 56 32 57 33 58 34 59 35 60 36 6 37 62 2 4 5 52 53 3 6 7 8 63 64 65 66 67 68 69 70 7 72 73 4 9 5 0 MODULE, BOTTOM OF STEERING COLUMN (B) BCM (C) OBDII (D) PARKING LIGHT SWITCH (E) T00_W INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 2 ORB-RSD-VW8-[ORBIT5A]-EN 205 Volkswagen Golf STD key AT
PAGE 4 OF 7 0 OFF START Insert key into ignition. 07 Press and release the module s programming button. 02 OFF START Turn key to ON position. 08 Release the brake pedal. 03 Wait, LED will turn solid GREEN for 2 seconds. 09 Wait, LED 2 will flash GREEN. 04 OFF START Turn key to OFF position. 0 Module Programming Procedure completed. 05 OFF START START vehicle for 5 seconds. 06 Press and hold the brake pedal. ORB-RSD-VW8-[ORBIT5A]-EN 205 Volkswagen Golf STD key AT
PAGE 5 OF 7 >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 0 Press unlock on aftermarket remote. 02 OFF START Insert key into ignition. 03 OFF START Turn key to ON position. 04 Press and release BRAKE pedal. 05 Take over procedure completed. ORB-RSD-VW8-[ORBIT5A]-EN 205 Volkswagen Golf STD key AT
INSTALLATION CHECKLIST - OF 2 PAGE 6 OF 7 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 7 Press the AUX 2 button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. CHECKLIST - WITH AFTERMARKET KEYFOB 9 Press the START/STOP button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. 2 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 20 Installation checklist completed. ORB-RSD-VW8-[ORBIT5A]-EN 205 Volkswagen Golf STD key AT
INSTALLATION CHECKLIST - 2 OF 2 PAGE 7 OF 7 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? CHECKLIST - WITH OEM KEYFOB NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 2 Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. ORB-RSD-VW8-[ORBIT5A]-EN 205 Volkswagen Golf STD key AT