Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-HA3-EN AVAILABLE FOR : ADS-AL CA Rev. Date: May 15, 2017 Doc. No.: ##39060## HA3 U.S. PATENT NO. 8,856,780 PLEASE VISIT WWW.IDATALINK.COM FOR COMPLETE PRODUCT DETAILS The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. 2017 NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.
Page 2 of 9 ADS-AL(DL)-HA3-EN Doc. No.: ##39060## 20170512 INSTALL TYPE SELECTION FEATURES MAKE MODEL YEAR INSTALL TYPE DATA IMMOBILIZER BYPASS ARM OEM ALARM ACURA DISARM OEM ALARM DOOR LOCK DOOR UNLOCK A/M ALARM CTRL FROM OEM REMOTES A/M RS CTRL FROM OEM REMOTES AUTOLIGHT CTRL* TRUNK/HATCH RELEASE POWER LIFTGATE POWER SLIDING DOOR (L)*** POWER SLIDING DOOR (R)*** DOOR STATUS OUTPUT TRUNK STATUS OUTPUT HOOD STATUS OUTPUT** TACHOMETER OUTPUT E-BRAKE OUTPUT BRAKE PEDAL STATUS OUTPUT TL 09-14 1 TSX 09-14 1 ZDX 10-11 1 Accord 08-12 1 Accord Crosstour 10-12 1 Civic 12-15 2 Civic Hybrid 12-13 2 CR-V 12-16 2 Odyssey 11-13 1 Odyssey 14-17 1 Pilot 09-15 1 *This feature will unlock then lock the vehicle s doors on RS shutdown. To turn it off, deactivate the RAP shutdown. (See module navigation chart) **Available only if vehicle is equipped with factory hood switch. ***When vehicle is remote started, feature will not be functional. Use traditional hardwired installation method for feature to be functional during remote start. HONDA
Page 3 of 9 ADS-AL(DL)-HA3-EN Doc. No.: ##39060## 20170512 WARNING: READ CAREFULLY IMPORTANT I II III Ground When Running from Remote Starter must be provided BEFORE Ignition. Failure to comply may result in immobilizer bypass malfunction during remote start. If Ground When Running from Remote Starter CAN T be provided BEFORE Ignition, use a separate TB-HA for immobilizer bypass ONLY. - DO NOT program unlock before start on the Remote Starter. - DO NOT change Remote Starter OEM alarm control default settings. Failure to comply may result in product malfunction.
Page 4 of 9 ADS-AL(DL)-HA3-EN Doc. No.: ##39060## 20170512 TYPE 1 - WIRE CROSS REFERENCE CHART MAKE MODEL YEAR WIRE DESCRIPTION NAME ACURA COLOR TYPE POSITION WIRE COLOR POLARITY HONDA MODULE LOCATION COMPONENT LOCATOR TL TSX ZDX Accord Accord Crosstour Odyssey Pilot 09-14 09-14 10-11 08-12 10-12 11-17 09-15 Key Data ~ White 7 pin 6 Purple (DATA) At immobilizer ~ Ignition ~ White 7 pin 2 Brown (+) At immobilizer ~ Key Data ~ White 7 pin 6 Pink (DATA) At immobilizer ~ CanH ~ White 7 pin 4 White (DATA) At immobilizer ~ CanL ~ White 7 pin 3 LtGreen (DATA) At immobilizer ~
Page 5 of 9 ADS-AL(DL)-HA3-EN Doc. No.: ##39060## 20170512 TYPE 1 - WIRING DIAGRAM STANDARD 12 VOLT, GROUND AND IGNITION SWITCH CONNECTIONS ARE STILL REQUIRED FROM THE REMOTE STARTER. REMOTE STARTER TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT RIGHT SLIDING DOOR OR TAILGATE WINDOW (-) OUTPUT LEFT SLIDING DOOR (-) OUTPUT DISARM (-) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 12V (+) GROUND (-) GWR (-) OUTPUT DATA MODE REQUIRED -> BRAKE (+) INPUT REQUIRED -> HOOD STATUS (-) INPUT OPTIONAL -> TRUNK STATUS (-) INPUT OPTIONAL -> DOOR STATUS (-) INPUT LEGEND NOT REQUIRED IN DATA MODE (1-WAY) NOT REQUIRED IN DATA MODE (2-WAY) USE DATA MODE OR HARDWIRE MODE RIGHT SLIDING DOOR (-) INPUT OR TAILGATE WINDOW (-) INPUT DATA MODE GWR (-) INPUT - BLUE/WHITE (NC) NO WIRE GROUND - BLACK 12V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK (-) INPUT - BLUE/BLACK TRUNK/LIFTGATE (-) INPUT - RED/WHITE DISARM (-) INPUT - BROWN LEFT SLIDING DOOR (-) INPUT - PURPLE/YELLOW 2 POSSIBLE APPLICATIONS - PURPLE/BLACK (NC) WHITE STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK - IGNITION (+) SIDE WHITE/RED - IGNITION (+) VEHICLE SIDE WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - HOOD STATUS (-) OUTPUT BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK - KEY DATA ORANGE/WHITE (NC) ORANGE (NC) PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED - BRAKE (+) OUTPUT GRAY/YELLOW (NC) CANL CANH DATA 1 2 3 4 5 6 7 NOTE SINCE THE MODULE INCLUDES A DISARM INPUT FEATURE, BOTH UNLOCK BEFORE START AND LOCK AFTER START FEATURES ARE NOT REQUIRED. IGNITION (+)
Page 6 of 9 ADS-AL(DL)-HA3-EN Doc. No.: ##39060## 20170512 TYPE 2 - WIRE CROSS REFERENCE CHART MAKE MODEL YEAR WIRE DESCRIPTION NAME COLOR TYPE POSITION HONDA WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR Civic Civic Hybrid CR-V 12-15 12-13 12-16 Ignition ~ White 7 pin 2 Yellow (+) Ignition switch ~ CanH ~ White 7 pin 4 Pink (DATA) Ignition switch ~ CanL ~ White 7 pin 3 Blue (DATA) Ignition switch ~ Key Data ~ White 7 pin 6 LtGreen (DATA) Ignition switch ~ Ignition ~ White 7 pin 2 Yellow (+) Ignition switch ~ CanH ~ White 7 pin 4 Pink (DATA) Ignition switch ~ CanL ~ White 7 pin 3 Blue (DATA) Ignition switch ~ Key Data ~ White 7 pin 6 LtGreen (DATA) Ignition switch ~ Ignition ~ White 7 pin 2 DkBlue (+) Ignition switch ~ CanH ~ White 7 pin 4 Pink (DATA) Ignition switch ~ CanL ~ White 7 pin 3 Blue (DATA) Ignition switch ~ Key Data ~ White 7 pin 6 Yellow (DATA) Ignition switch ~
Page 7 of 9 ADS-AL(DL)-HA3-EN Doc. No.: ##39060## 20170512 TYPE 2 - WIRING DIAGRAM STANDARD 12 VOLT, GROUND AND IGNITION SWITCH CONNECTIONS ARE STILL REQUIRED FROM THE REMOTE STARTER. REMOTE STARTER TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT DISARM (-) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 12V (+) GROUND (-) GWR (-) OUTPUT DATA MODE REQUIRED -> REQUIRED -> OPTIONAL -> OPTIONAL -> BRAKE STATUS (+) INPUT HOOD STATUS (-) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT LEGEND NOT REQUIRED IN DATA MODE (1-WAY) NOT REQUIRED IN DATA MODE (2-WAY) USE DATA MODE OR HARDWIRE MODE CONNECT TO GROUND TO ENABLE AUTOMATIC RELOCK AFTER START DATA MODE GWR (-) INPUT - BLUE/WHITE (NC) NO WIRE GROUND - BLACK 12V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE DISARM (-) INPUT - BROWN (NC) PURPLE/YELLOW GROUND (-) INPUT - PURPLE/BLACK (NC) WHITE STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK - IGNITION (+) SIDE WHITE/RED - IGNITION (+) VEHICLE SIDE WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - HOOD STATUS (-) OUTPUT BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK - KEY DATA ORANGE/WHITE (NC) ORANGE (NC) PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED - BRAKE STATUS (+) OUTPUT GRAY/YELLOW (NC) CANL CANH DATA 1 2 3 4 5 6 7 IGNITION (+)
Page 8 of 9 ADS-AL(DL)-HA3-EN Doc. No.: ##39060## 20170512 INSTALLATION MODE SELECTION 1 Press and release programming button to select installation mode. LED flashes (1X) once = DATA MODE LED flashes (2X) twice = STANDARD HARDWIRE MODE 2! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. MODULE PROGRAMMING PROCEDURE 1 Insert key into ignition. 4 OFF Turn key to OFF position. 2 3 ON Turn key to ON position. Wait, LED will turn solid GREEN for 2 seconds. 5! Æ x1 Press UNLOCK on the OEM remote. If the vehicle is equipped with a power liftgate: Open and close the power liftgate with the OEM keyfob. 6 Module Programming Procedure completed.
Page 9 of 9 ADS-AL(DL)-HA3-EN Doc. No.: ##39060## 20170512 IDENTIFY VEHICLE YEAR 1 Locate the Vehicle Identification Number (VIN), identify the 10th character then match it to its corresponding year. Æ 4 3 A 5 Y 1 N 5 T A L 8 D 5 R 0 X Æ A 1980 L 1990 Y 2000 A 2010 B 1981 M 1991 1 2001 B 2011 C 1982 N 1992 2 2002 C 2012 D 1983 P 1993 3 2003 D 2013 E 1984 R 1994 4 2004 E 2014 F 1985 S 1995 5 2005 F 2015 G 1986 T 1996 6 2006 G 2016 H 1987 V 1997 7 2007 H 2017 J 1988 W 1998 8 2008 J 2018 K 1989 X 1999 9 2009 K 2019 LED STATUS Flashing RED DIAGNOSTICS DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming MODULE DIAGNOSTICS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTORY RESET PROCEDURE 1 2 DISCONNECT all connectors from module EXCEPT the black 4-PIN standard or optional data connector. DISCONNECT black 4-PIN standard or optional data connector. 5 6 LED will turn solid red for 2 seconds. RESET COMPLETED. RECONNECT all connectors. 3 PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data connector. 7! Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 4 When LED flashes red, RELEASE programming button.