Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-NI9-EN AVAILABLE FOR : ADS-AL CA Rev. Date: January 8, 08 Doc. No.: ##4734## NI9 U.S. PATENT NO. 8,856,780 PLEASE VISIT WWW.IDATALINK.COM FOR COMPLETE PRODUCT DETAILS The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. 08 TERMS OF USE: automotive Data solutions inc. ( ads ) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ads product in a vehicle, it is the Certified Technician s responsibility to review the most current Product Guide, install Guide and vehicle-specific notes available in Weblink. ads is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ads reserves itself the right to suspend any Weblink account without notice and decline to offer technical support to non- Certified Technicians, non-compliant Certified Technicians or end users.
Page of ADS-AL(DL)-NI9-EN Doc. No.: ##4734## 0808 INSTALL TYPE SELECTION features Make MoDel NOTE I On the remote starter, configure the feature LOCK AFTER SHUTDOWN, to control RAP/autolight shutdown. Year InStall type Data IMMoBIlIZer BYPaSS SecUre takeover a/m alarm ctrl from oem remotes a/m rs ctrl from oem remotes Door StatUS output trunk StatUS output Brake PeDal StatUS output tachometer output e-brake output Qashqai STD key AT 7 nissan Rogue STD key AT 4-6 Rogue STD key AT 7 Rogue STD key AT 8 3 Rogue Sport STD key AT 7
Page 3 of ADS-AL(DL)-NI9-EN Doc. No.: ##4734## 0808 COMPONENT LOCATOR A B
Page 4 of ADS-AL(DL)-NI9-EN Doc. No.: ##4734## 0808 TYPE - WIRE CROSS REFERENCE CHART - OF nissan Make MoDel Year DeScrIPtIon name type PoSItIon PolarItY MoDUle location component locator CanH OBDII White 6 pin 06 Blue (DATA) At OBDII B CanL OBDII White 6 pin 4 Pink (DATA) At OBDII B Negative Ignition M8 Gray 40 pin 7 Yellow (-) At BCM A Negative Ignition M8 Gray 40 pin 8 LtPurple/White or Green/White (-) At BCM A Rogue STD key AT 4-6 Negative Ignition 3 M8 Gray 40 pin 5 Brown (-) At BCM A Ignition OBDII White 6 pin 08 Yellow (+) At OBDII B V OBDII White 6 pin 6 White (+) At OBDII B Unlock M9 Black 40 pin 3 Pink (-) At BCM A Lock M9 Black 40 pin Brown (-) At BCM A Power Liftgate ~ Green 08 pin 06 LtGreen (-) At switch, on lower dash panel A Ground OBDII White 6 pin 04 Black (-) At OBDII B Negative Starter E9 Black 4 pin 9 Green (-) At BCM A
Page 5 of ADS-AL(DL)-NI9-EN Doc. No.: ##4734## 0808 TYPE - WIRING DIAGRAM - OF 4 3 8 7 6 5 POWER LIFTGATE (-) POWER LIFTGATE CONNECTOR LTGREEN (LOWER DASH PANEL) REMOTE STARTER OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH 3 4 5 6 7 8 9 CANL GROUND (-) 0 3 4 5 6 V (+) CANH IGNITION (+) TRUNK (-) OUTPUT TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT UNLOCK (-) OUTPUT <- OPTIONAL LOCK (-) OUTPUT <- OPTIONAL V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (-WAY) REQUIRED -> GROUND (-) INPUT REQUIRED -> V (+) INPUT REQUIRED -> BRAKE STATUS (+) INPUT REQUIRED -> IGNITION (+) OUTPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT WARNING: DO NOT CONNECT ANY OTHER ACCESSORY, IGNITION OR START WIRE FROM THE REMOTE STARTER TO THE VEHICLE USE OR HARDWIRE MODE OEM REMOTE REMAINS FUNCTIONAL DURING REMOTE START SEQUENCE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK V (+) - RED LOCK (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK (NC) RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK - IGNITION (-) OUTPUT WHITE/RED (NC) WHITE - GROUND (-) INPUT YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW (NC) BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE - BRAKE STATUS (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED - GROUND (-) INPUT BLUE/YELLOW - STARTER (-) OUTPUT GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) LOCK (-) UNLOCK (-) M9 - BLACK THE SECURITY LIGHT WILL FLASH DURING THE REMOTE START SEQUENCE AND WILL TURN OFF UPON VEHICLE TAKEOVER. 40 39 38 37 36 35 34 33 3 3 30 9 8 7 6 5 4 3 M8 - GRAY 40 39 38 37 36 35 34 33 3 3 30 9 8 7 6 5 4 3 E9 - BLACK IGNITION (-) IGNITION 3 (-) IGNITION (-) 4 3 0 9 8 7 6 5 4 3 STARTER (-) BCM
Page 6 of ADS-AL(DL)-NI9-EN Doc. No.: ##4734## 0808 TYPE - WIRE CROSS REFERENCE CHART - OF Make MoDel Year DeScrIPtIon name type PoSItIon nissan PolarItY MoDUle location component locator Qashqai STD key AT Rogue STD key AT Rogue Sport STD key AT 7 7 7 CanH ~ Green 40 pin 0 Blue (DATA) At BCM A CanL ~ Green 40 pin 40 Pink (DATA) At BCM A Negative Ignition M8 Gray 40 pin 7 LtPurple/LtGreen (-) At BCM A Negative Ignition M8 Gray 40 pin 8 LtPurple/Blue (-) At BCM A Negative Ignition 3 M8 Gray 40 pin 5 LtPurple//Pink (-) At BCM A Ignition OBDII White 6 pin 08 Yellow (+) At OBDII B V OBDII White 6 pin 6 White (+) At OBDII B Unlock M9 Black 40 pin 3 Pink (-) At BCM A Lock M9 Black 40 pin Brown (-) At BCM A Power Liftgate ~ Green 08 pin 06 LtGreen (-) At switch, on lower dash panel A Ground OBDII White 6 pin 04 Black (-) At OBDII B Negative Starter E9 Black 4 pin 9 Blue (-) At BCM A CanH ~ Green 40 pin 0 Blue (DATA) At BCM A CanL ~ Green 40 pin 40 Pink (DATA) At BCM A Negative Ignition M8 Gray 40 pin 7 Yellow (-) At BCM A Negative Ignition M8 Gray 40 pin 8 LtPurple/White or Green/White (-) At BCM A Negative Ignition 3 M8 Gray 40 pin 5 Brown (-) At BCM A Ignition OBDII White 6 pin 08 Yellow (+) At OBDII B V OBDII White 6 pin 6 White (+) At OBDII B Unlock M9 Black 40 pin 3 Pink (-) At BCM A Lock M9 Black 40 pin Brown (-) At BCM A Power Liftgate ~ Green 08 pin 06 LtGreen (-) At switch, on lower dash panel A Ground OBDII White 6 pin 04 Black (-) At OBDII B Negative Starter E9 Black 4 pin 9 Green (-) At BCM A CanH ~ Green 40 pin 0 Blue (DATA) At BCM A CanL ~ Green 40 pin 40 Pink (DATA) At BCM A Negative Ignition M8 Gray 40 pin 7 LtPurple/LtGreen (-) At BCM A Negative Ignition M8 Gray 40 pin 8 LtPurple/Blue (-) At BCM A Negative Ignition 3 M8 Gray 40 pin 5 LtPurple//Pink (-) At BCM A Ignition OBDII White 6 pin 08 Yellow (+) At OBDII B V OBDII White 6 pin 6 White (+) At OBDII B Unlock M9 Black 40 pin 3 Pink (-) At BCM A Lock M9 Black 40 pin Brown (-) At BCM A Power Liftgate ~ Green 08 pin 06 LtGreen (-) At switch, on lower dash panel A Ground OBDII White 6 pin 04 Black (-) At OBDII B Negative Starter E9 Black 4 pin 9 Blue (-) At BCM A
Page 7 of ADS-AL(DL)-NI9-EN Doc. No.: ##4734## 0808 TYPE - WIRING DIAGRAM - OF 4 3 8 7 6 5 POWER LIFTGATE (-) POWER LIFTGATE CONNECTOR LTGREEN (LOWER DASH PANEL) OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH 3 4 5 6 7 8 9 0 3 4 5 6 V (+) IGNITION (+) REMOTE STARTER GROUND (-) TRUNK (-) OUTPUT TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT UNLOCK (-) OUTPUT <- OPTIONAL LOCK (-) OUTPUT <- OPTIONAL V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (-WAY) THE SECURITY LIGHT WILL FLASH DURING THE REMOTE START SEQUENCE AND WILL TURN OFF UPON VEHICLE TAKEOVER. REQUIRED -> GROUND (-) INPUT REQUIRED -> V (+) INPUT REQUIRED -> BRAKE STATUS (+) INPUT REQUIRED -> IGNITION (+) OUTPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT WARNING: DO NOT CONNECT ANY OTHER ACCESSORY, IGNITION OR START WIRE FROM THE REMOTE STARTER TO THE VEHICLE USE OR HARDWIRE MODE OEM REMOTE REMAINS FUNCTIONAL DURING REMOTE START SEQUENCE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK V (+) - RED LOCK (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK (NC) RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK - IGNITION (-) OUTPUT WHITE/RED (NC) WHITE - GROUND (-) INPUT YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW (NC) BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE - BRAKE STATUS (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED - GROUND (-) INPUT BLUE/YELLOW - STARTER (-) OUTPUT GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) LOCK (-) UNLOCK (-) E9 - BLACK M9 - BLACK 40 39 38 37 36 35 34 33 3 3 30 9 8 7 6 5 4 3 BCM 4 3 0 9 8 7 6 5 4 3 STARTER (-) 40 39 38 37 36 35 34 33 3 3 30 9 8 7 6 5 4 3 IGNITION (-) IGNITION 3 (-) IGNITION (-) M8 - GRAY CANH CANL GREEN 0 9 8 7 6 5 4 3 40 39 38 37 36 35 34 33 3 3 30 9 8 7 6 5 4 3
Page 8 of ADS-AL(DL)-NI9-EN Doc. No.: ##4734## 0808 TYPE 3 - WIRE CROSS REFERENCE CHART - OF Make MoDel Year DeScrIPtIon name type nissan PoSItIon PolarItY MoDUle location component locator CanH ~ Green 40 pin 0 Blue (DATA) At BCM A CanL ~ Green 40 pin 40 Pink (DATA) At BCM A Negative Ignition M8 Gray 40 pin 7 Yellow (-) At BCM A Rogue STD key AT 8 Negative Ignition M8 Gray 40 pin 8 LtPurple/White or Green/White (-) At BCM A Negative Ignition 3 M8 Gray 40 pin 5 Brown (-) At BCM A Ignition OBDII White 6 pin 08 Yellow (+) At OBDII B V OBDII White 6 pin 6 White (+) At OBDII B Unlock M9 Black 40 pin 3 Pink (-) At BCM A Lock M9 Black 40 pin Brown (-) At BCM A Power Liftgate ~ Green 08 pin 06 LtGreen (-) At switch, on lower dash panel A Ground OBDII White 6 pin 04 Black (-) At OBDII B Negative Starter E9 Black 4 pin 9 Green (-) At BCM A Driver Door Pin ~ Green 40 pin 7 LtBlue (-) At BCM A
Page 9 of ADS-AL(DL)-NI9-EN Doc. No.: ##4734## 0808 TYPE 3 - WIRING DIAGRAM - OF 4 3 8 7 6 5 POWER LIFTGATE (-) POWER LIFTGATE CONNECTOR LTGREEN (LOWER DASH PANEL) OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH 3 4 5 6 7 8 9 0 3 4 5 6 V (+) IGNITION (+) REMOTE STARTER GROUND (-) TRUNK (-) OUTPUT TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT UNLOCK (-) OUTPUT <- OPTIONAL LOCK (-) OUTPUT <- OPTIONAL V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (-WAY) THE SECURITY LIGHT WILL FLASH DURING THE REMOTE START SEQUENCE AND WILL TURN OFF UPON VEHICLE TAKEOVER. REQUIRED -> GROUND (-) INPUT REQUIRED -> V (+) INPUT REQUIRED -> BRAKE STATUS (+) INPUT REQUIRED -> IGNITION (+) OUTPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT WARNING: DO NOT CONNECT ANY OTHER ACCESSORY, IGNITION OR START WIRE FROM THE REMOTE STARTER TO THE VEHICLE USE OR HARDWIRE MODE OEM REMOTE REMAINS FUNCTIONAL DURING REMOTE START SEQUENCE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK V (+) - RED LOCK (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK (NC) RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK - IGNITION (-) OUTPUT WHITE/RED (NC) WHITE - GROUND (-) INPUT YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - DRIVER DOOR PIN (-) OUTPUT BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE - BRAKE STATUS (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED - GROUND (-) INPUT BLUE/YELLOW - STARTER (-) OUTPUT GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) E9 - BLACK LOCK (-) UNLOCK (-) M9 - BLACK BCM 4 3 0 9 8 7 6 5 4 3 40 39 38 37 36 35 34 33 3 3 30 9 8 7 6 5 4 3 STARTER (-) 40 39 38 37 36 35 34 33 3 3 30 9 8 7 6 5 4 3 IGNITION (-) IGNITION 3 (-) IGNITION (-) M8 - GRAY CANH CANL DRIVER DOOR PIN GREEN 0 9 8 7 6 5 4 3 40 39 38 37 36 35 34 33 3 3 30 9 8 7 6 5 4 3
Page 0 of ADS-AL(DL)-NI9-EN Doc. No.: ##4734## 0808 INSTALLATION MODE SELECTION Press and release programming button to select installation mode. LED flashes (X) once = LED flashes (X) twice = STANDARD HARDWIRE MODE! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. MODULE PROGRAMMING PROCEDURE OFF ACC ON START Set ignition to ON position. 8 ÆÆ WARNING: Disconnect power last. Disconnect module from vehicle. Wait, LED will turn solid RED, then solid GREEN for second, then solid RED. 9 Æ Connect module to computer and proceed with extended programming. 3 OFF ACC ON START Set ignition to OFF position. 0 Æ WARNING: Connect power first. Connect module to vehicle. 4 Wait, LED will turn OFF. OFF ACC ON START Set ignition to ON position. 5 OFF ACC ON START Set ignition to ON position. Wait, LED will turn solid GREEN for seconds. 6 If LED flashes GREEN rapidly, proceed with step 7. If LED turns solid GREEN for seconds, proceed with step 3. 3 OFF ACC ON START Set ignition to OFF position. 7 OFF ACC ON START Set ignition to OFF position. 4 Module Programming Procedure completed.
Page of ADS-AL(DL)-NI9-EN Doc. No.: ##4734## 0808 IDENTIFY VEHICLE YEAR Locate the Vehicle Identification Number (VIN), identify the 0th character then match it to its corresponding year. Æ 4 3 A 5 Y N 5 T A L 8 D 5 R 0 X Æ a 980 l 990 Y 000 a 00 B 98 M 99 00 B 0 c 98 n 99 00 c 0 D 983 P 993 3 003 D 03 e 984 r 994 4 004 e 04 f 985 S 995 5 005 f 05 G 986 t 996 6 006 G 06 H 987 V 997 7 007 H 07 J 988 W 998 8 008 J 08 k 989 X 999 9 009 k 09 led StatUS Flashing RED DIaGnoStIcS DUrInG ProGraMMInG DUrInG remote Start WItH IGnItIon off Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming MODULE DIAGNOSTICS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTORY RESET PROCEDURE DISCONNECT all s from module EXCEPT the black 4-PIN standard or optional data. DISCONNECT black 4-PIN standard or optional data. 5 6 LED will turn solid red for seconds. RESET COMPLETED. RECONNECT all s. 3 PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data. 7! Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 4 When LED flashes red, RELEASE programming button.