Air Powered Double Diaphragm Pumps

Air Powered Double Diaphragm Pumps

Notes.

TC-X 030 Series Standard Diaphragm Pumps with 1/4" Connections Liquid Flow Rate: Maximum Air Inlet Pressure: Wetted Body Material Options; 1 to 8 L/min. (2.14 GPM) Flat Valve = 0 mm. 0.7 MPa (100 PSI) Ryton Air Motor (PPS), Looped C Spring Air Spool, Flat Check Valves, Side Port Liquid Connections. Internal Silencer. Fully Bolted Body. ¼" Threaded Connections PT. PVDF, PTFE. (For PTFE > Refer to the TC-X030TT Series). Diaphragm / Check Valve Materials: PTFE for all models. Certification: CE. ATEX. Filter Regulator. Filter Regulator with Auto Drain. Filter Regulator Lubricator. Bolt Caps. Notes: New pump series. Very low flow rates. Available in PVDF. Very Compact size. New footprint. Grease or oil Lubrication is not necessary during normal operation. Also available with NPT connections. PVDF Model > TC-X030VT

TC-X 050 Series Standard Diaphragm Pumps with 1/4" Connections 1 to 11.5 L/min. (3.1 GPM) Flat valve = 0 mm. Maximum Air Inlet Pressure: 0.7 MPa (100 PSI) Maximum Dry Suction Lift: 1.5 m (5 Feet) Discharge Volume: 35 cc Per Cycle 400 Cycles per minute Ryton Air Motor (PPS), Looped C Spring Air Spool, Flat Check Valves, Side Port Liquid Connections. Internal Silencer. Fully Bolted Body. PP model with Multiport connections as standard. ¼" Threaded Connections. PT Wetted Body Material Options; PVDF. PPG. POM. Al. SUS. PP. PPC, PTFE. (For PTFE refer to the TC-X030TT Series). Diaphragm / Check Valve Materials: PTFE for all models. Certification: CE. ATEX. (Some models) FDA. (Some Models) Common Pump Options: Ball check valve Pump for Liquid Solids handling. (BV) FDA Pump Series (SUS Models). Drum Pump Series. (D) Multiport Connections. (MP) Split Inlet Manifolds (I) Split Discharge Manifolds (O) Split Suction & Discharge manifolds (Z) Filter Regulator. Filter Regulator with Auto Drain. Filter Regulator Lubricator. Notes: Available in all materials. Very Compact size. Lubrication not necessary. Also available with NPT connections. SUS > TC-X050ST-MP PPG > TC-X050PT AL > TC-X050AT PVDF > TC-X050VT-MP Pure PP > TC-X050PT-PP POM > TC-X050DT

TC-X 100 Series Standard Diaphragm Pumps with 3/8 Connections Maximum Air Inlet Pressure: 1 to 19 L/min. (5.7 GPM) 1.0 mm 0.7 MPa (100 PSI) Aluminium Air Motor, Spring-Less Air Spool, Ball Check Valves, Centre Port Liquid Connections. External Silencer. Fully Bolted Body. PP model with Multiport as standard. PP model with Multiport connections as standard. 3/8 Threaded Connections. PT Wetted Body Material Options; PPG. & PP. Diaphragm / Check Valve PTFE. CR. EDPM. NBR. TPEE. TPO. Materials: Certification: CE. Common Pump Options: PTFE Ball Valve Set PTFE coating for Air motor section MP Multi port Connections Filter Regulator. Filter Regulator with Auto Drain. Filter Regulator Lubricator. High Performance Muffler. Speed Control Muffler Notes: suitable for frequent start stop, dead head & high back pressure type applications. Available in PPG and new PP body materials. Lubrication not necessary during normal operation. Also available with NPT connections. PPG > TC-X100PT Pure PP > TC-X100PT-PP

TC-X 101 Series Standard Diaphragm Pumps with 3/8 Connections 1 to 22 L/min. (6 GPM) 1.0 mm Maximum Air Inlet Pressure: 0.7 MPa (100 PSI) Maximum Dry Suction Lift: 3 m (10 Feet) Discharge Volume: 76 cc per cycle 300 Cycles Per minute Aluminium Air Motor, Spring-Less Air Spool, Ball Check Valves, Multi Port Liquid Connections. External Silencer. Fully Bolted Body. 3/8 Threaded Connections. PT Wetted Body Material Options; Al. & SUS. Diaphragm / Check Valve Materials: PTFE. CR. EDPM. NBR. TPEE. TPO. Certification: CE. ATEX. FDA. (SUS Models) Common Pump Options: FDA Pump Series (For SUS Pumps). Drum Pump Series. (For Aluminium or SUS Pumps) ½ Centre Port Connections. SUS Balls Kit (For Aluminium or SUS Pumps) SUS Seats Kit (For Aluminium Pumps) SUS Guides Kit (For Aluminium Pumps) PTFE Coating for air motor section Filter Regulator. Filter Regulator with Auto Drain. Filter Regulator Lubricator. High Performance Muffler. Speed Control Muffler Notes: suitable for frequent start stop, dead head & high back pressure type applications. Available in aluminium and stainless steel body materials. Multi-port liquid connection options. Various diaphragm materials. Compact size. Oil or grease lubrication is not necessary during normal operation. Also available with NPT connections. AL > TC-X101AN SUS > TC-X101SS

TC-X 102 Series Standard Diaphragm Pumps with 3/8" Connections Maximum Air Inlet Pressure: 1 to 22 L/min. (6 GPM) 1.0 mm 0.7 MPa (100 PSI) Ryton Air Motor (PPS), C-Spring Air Spool, Ball Check Valves, Side Port Connections. External Silencer. Fully Bolted Body. Wetted Body Material Options; Diaphragm / Check Valve Materials: Certification: Common Pump Options: 3/8" Threaded Connections. PT PPG. PTFE. CR. EDPM. NBR. TPEE. TPO. CE. PTFE Ball Valve Kit. Filter Regulator. Filter Regulator with Auto Drain. Filter Regulator Lubricator. High Performance Muffler. Speed Control Muffler Notes: available only in PPG. Chemically resistant air section (PPS). Compact size. Lubrication not necessary during normal operation. Old model however still available for sale. Also available with NPT connections. PPG > TC-X102PT

TC-X 150 Series Standard Diaphragm Pumps with 1/2 Connections 1 to 28 L/min. (7.4 GPM) 1.0 mm Maximum Air Inlet Pressure: 0.7 MPa (100 PSI) Maximum Dry Suction Lift: 3 m (10 Feet) Discharge Volume: 93 cc per cycle 300 cycles per min Aluminium Air Motor, Spring-Less Air Spool, Flat & Ball Check Valves, Side Port Connections. External Silencer. Fully Bolted Body. 1/2 Threaded Connections. PT Wetted Body Material Options; PPG & POM. Diaphragm / Check Valve Materials: PTFE. CR. EDPM. NBR. TPEE. TPO. Certification: CE. ATEX (Some Models) Common Pump Options: Ball Valve Pump Range PTFE Ball Valve Set PTFE Coating for air motor section Filter Regulator. Filter Regulator with Auto Drain. Filter Regulator Lubricator. High Performance Muffler. Speed Control Muffler. Notes: suitable for frequent start stop, dead head & high backpressure type applications. Available in PPG and POM (Atex) body materials. Lubrication not necessary during normal operation. Both ball and flat check valve pumps are available. Also available with NPT connections. POM > TC-X150DT PPG > TC-X150PT

TC-X 151 Series Standard Diaphragm Pumps with 1/2" Connections 1 to 51 L/min. ( 13.5 GPM) 1.0 mm Maximum Air Inlet Pressure: 0.7 MPa (100 PSI) Maximum Dry Suction Lift: 2.4 m (8 Feet) Flat valves. 1.5 m (5 Feet) Ball valves Discharge Volume: 128 cc per cycle 400 Cycles per minute Ryton Air Motor (PPS), C-Spring Air Spool, Flat & Ball Check Valves, Side Port Connections. Internal Silencer. Fully Bolted Body. ½ Threaded Connections. PT Wetted Body Material Options; PVDF. PPG. POM. Al. SUS. Diaphragm / Check Valve Materials: PTFE. CR. EDPM. NBR. TPEE. TPO. Certification: CE. ATEX. (Some Models) FDA. (SUS Models) Common Pump Options: Ball check valve Pump Range for Liquid Solids handling. (BV) FDA Pump Series (SUS). Multiport Connections. (MP) Split Inlet Manifolds (I) Split Discharge Manifolds (O) Split suction & discharge manifolds (Z) Filter Regulator. Filter Regulator with Auto Drain. Filter Regulator Lubricator. High Performance Muffler. Speed Control Muffler. Notes: Now superseded by the new D152 Series. However still available and in various materials. Lubrication not necessary during normal operation. Also available with NPT connections. AL > TC-X151AH PPG > TC-X151PT SUS > TC-X151ST PVDF > TC-X151VT

TC-X 152 Series Standard Diaphragm Pumps with 1/2" Connections 1 to 60 L/min. (15.9 GPM) 2.0 mm Maximum Air Inlet Pressure: 0.7 MPa (100 PSI) Polypropylene Air Motor (PPG), Looped C Spring Air Spool, Flat & Ball Check Valves, Multi Port Liquid Connections. Internal Silencer. Fully Bolted Body. Multi Footprint options ½ Threaded Connections. PT. PTFE Model also available with Flanges. Wetted Body Options; PP. PVDF. POM. Al. SUS. PPC, PTFE. (For PTFE Refer to TC-X152TT Series) Diaphragm / Check Valve PTFE. CR. EDPM. NBR. TPEE. TPO. Materials: Certification: CE. ATEX. (Some Models) FDA. (SUS Models) Common Pump Options: FDA Pump Series (SUS). Drum Pump Series. (D) Split Inlet Manifolds (I) Split Discharge Manifolds (O) SUS Balls, Seats & Guides kits. Santoprene Back Up Diaphragms for PTFE Fitted Pumps (SB) Filter Regulator. Filter Regulator with Auto Drain. Filter Regulator Lubricator. High Performance Muffler. Speed Control Muffler. External Silencer. Notes: new model available in all materials. Very high flow rates. Large solids size. Low air consumption. Multiport liquid connections. Standardized body dimensions, multi footprint and common connection dimensions. Lubrication not necessary during normal operation. PPG air motor for increased chemical resistance. Also available with NPT connections. Al > TC-X152AN PP>TC-X152PT-PP SUS > TC-X152SS PVDF > TC-X152VT

TC-X 202 Series Standard Diaphragm Pumps with 3/4" Connections 1 to 120 L/min. (31.7 GPM) 2.0 mm Maximum Air Inlet Pressure: 0.7 MPa (100 PSI) Maximum Dry Suction Lift: 5.5 m (18 feet) (Rubber Diaphragms) Discharge Volume: Rubber diaphragms 615 cc PTFE diaphragms 539 cc Polypropylene Air Motor (PPG), Looped C Spring Air Spool, Ball Check Valves, Side Port Liquid Connections. External Silencer. Fully Bolted Body. ¾ PT Threaded Connections & DIN Flange Connections. Wetted Body Material Options; PPG, PTFE. (For PTFE refer to the TC-X203TT Series) Diaphragm / Check Valve Materials: PTFE. CR. EDPM. NBR. TPEE. TPO. FPM. Certification: CE. Common Pump Options: PTFE Balls Kit Santoprene Back Up Diaphragms for PTFE Fitted Pumps (SB) Filter Regulator. Filter Regulator with Auto Drain. Filter Regulator Lubricator. High Performance Muffler. Speed Control Muffler. External Silencer. Destroke Cushions. Notes: ¾ Pumps available in PPG with a PPG air motor section for high chemical resistance. Available with threaded or flange connections. Lubrication not necessary during normal operation. Also available with NPT connections. PPG Threaded Connections > TC-X202PT PPG Flange Connections > TC-X202PT-FL

TC-X 252 Series Standard Diaphragm Pumps with 1 Connections 1 to 170 L/min. (46.2 GPM) 4.8 mm Maximum Air Inlet Pressure: 0.7 MPa (100 PSI) Maximum Dry Suction Lift: 5.5 m (18 Feet) Rubber fitted. Discharge Volume: 883 cc (Rubber Diaphragm) 787 cc (PTFE Diaphragm) Polypropylene Air Motor (PPG), Looped C Spring Air Spool, Ball Check Valves, Side Port Liquid Connections. External Silencer. Fully Bolted Body. Multi footprint options 1 PT Threaded Connections & DIN Flange Connections. Wetted Body Material Options; PPG, PVDF. Diaphragm / Check Valve PTFE. CR. EDPM. NBR. TPEE. TPO. FPM. Materials: Certification: CE. ATEX (Some Models) Common Pump Options: PTFE Balls Kit Santoprene Back Up Diaphragms for PTFE Fitted Pumps (SB) (TE) PTFE diaphragms with bonded rubber Backup Filter Regulator. Filter Regulator with Auto Drain. Filter Regulator Lubricator. High Performance Muffler. Speed Control Muffler. External Silencer. Destroke Cushions. Notes: 1 Pumps available in PPG & PVDF with a PPG air motor section for high chemical resistance. Available with both threaded or flange connections. Lubrication not necessary during normal operation. Also available with NPT threaded & ANSI Flange connections. PPG Threaded Connections PPG Flange Connections PVDF Flange Connections PVDF Thread Connections TC-X252PT TC-X252PT-FL TC-X252VT-FL TC-X252VT

TC-X 253 Series Standard Diaphragm Pumps with 1 Connections 1 to 220 L/min. (58.1 GPM) 6.5 mm Maximum Air Inlet Pressure: 0.2 to 0.7 MPa (30 to 100PSI) Discharge Volume Per Cycle: 800 ml (rubber fitted) 650 ml (PTFE Fitted) Polypropylene Air Motor (PPG), Looped C Spring Air Spool, Ball Check Valves, Multi Port Liquid Connections. External Silencer. Fully Bolted Body. Multi footprint options. Common Dimensions 1 Threaded Connections, PT. PTFE Model also available with Flanges Wetted Body Material Options; Aluminium, Cast Iron, Stainless Steel, PTFE. (For PTFE > refer to TC-X253TT Series). Diaphragm / Check Valve Materials: PTFE. CR. EDPM. NBR. TPEE. TPO. FPM. Certification: CE. ATEX FDA. (SUS Models) Common Pump Options: PTFE Balls Kit FDA Pump Series (SUS Models). 1.25 Centre Port Connections. 1.5 Centre Port Connections. High Vacuum Guides Kit (HV) Powder Pump Options (PDR) Santoprene Back Up Diaphragms for PTFE Fitted Pumps (SB) (TE) PTFE diaphragms with bonded rubber Backup Filter Regulator. Filter Regulator with Auto Drain. Filter Regulator Lubricator. High Performance Muffler. Speed Control Muffler. Destroke Cushions. Abrasion Pads. Carry Handles. Notes: New 1 Pumps available in Aluminium, Cast Iron, and Stainless Steel. PPG air motor section. New Compact Size. High Flow rates. Large Solids Size. Low air consumption compared to previous models. Multiport liquid connection options. Multi footprint options (6 positions) and common liquid connections. Lubrication not necessary during normal operation. Also available with NPT thread. AL > TC-X253AH SUS > TC-X253ST

TC-X 500 Series Standard Diaphragm Pumps with 2 Connections 1 to 730 L/min. (193 GPM) 8 mm Maximum Air Inlet Pressure: 0.1 to 0.85 MPa (123 PSI) on metallic models Aluminium Air Motor Section, Coil-Spring Air Motor, Ball Check Valves, External Silencers (2). Fully Bolted Body. Multi Footprint options. Metal; 2 PT. & DIN Flange. Plastic: DIN Flanges Only Wetted Body Material Options; Aluminium, Cast Iron, Stainless Steel. PPG. PVDF. Diaphragm / Check Valve Materials: PTFE. CR. EDPM. NBR. TPEE. TPO. FPM. Certification: CE. ATEX FDA (SUS Models) Common Pump Options: High Pressure Pumps (HP) Powder Pump (PDR) FDA Pumps (FDA) 316 SS PARABOLIC GUIDES (S7) (removable / replaceable Guides) Santoprene Back Up Diaphragms for PTFE Fitted Pumps (SB) Electro Polish SUS Pumps (EP20) (TE) PTFE diaphragms with bonded rubber Backup Filter Regulator. Filter Regulator with Auto Drain. Filter Regulator Lubricator. High Performance Muffler. Speed Control Muffler. Destroke Cushions. Abrasion Pads. Carry Handles. Notes: New 2 Pumps with Extremely High Flow Rates & A New Robust & Compact Body Design. Available in all materials with both Flange and Threaded Connections. Completely Non-lubricated Shuttle Valve. Pumps can operate from Very Low up to Very High Air Pressures and have up to 25% Better Air Consumption compared to previous models. Same Footprint and same Dimensions matching many Competitors Similar Models. Suited to Both Start Stop & Fully Continuous pumping applications. Can easily handle High Heads and Very Long Discharge Lines. Also very good for Filter Press & other Dead Head type processes. Also available with NPT threaded connections. Flange models match both DIN and ANSI.

TC-X (TT) Series Special PTFE Diaphragm Pumps in Various Sizes Standard DFS Models: TC-X030TT TC-X050TT TC-X152TT TCX152TT-FL TC-X203TT TC-X203TT-FL TC-X253TT TC-X253TT-FL Liquid Flow Rates; 8.2 L/min. 11.0 L/min. 50 L/min 55 L/Min 150 L/min Connections: ¼ PT ¼ PT ½ PT & DIN ¾ PT & DIN 1 PT & DIN Check Valves: Flat Flat Ball Ball Ball 0 mm 0 mm 2 mm 2mm 3 mm Air Pressure Range: 0.2-0.5 MPa (72 PSI) Special range of PTFE Pumps designed to transfer highly corrosive chemicals. Can also be used in Clean Room Type Chemical Transfer Processes such as in the manufacture of Semiconductors. Wetted Body Material; Standard Grade PTFE Diaphragm / Check Valve PTFE on all Models Materials: Certification: CE. Special Pump Options: TC-X152TT-SP20 152 pump with ¾ flange connections TC-X050TT-H High temperature model for Liquid temperatures up to 150 C Filter Regulator. Notes: Air Powered Self priming pumps. 100% PTFE/PFA Wetted Construction. Manufactured from Virgin PTFE. Highly Competitive Liquid Flow Rates. Compact Size and Fully Bolted Construction. New Looped C Air Motor Design Technology. (Pat. Pending) Competitive Air Consumption Compared to Previous Models. Lubrication Free Operation. Easy Repair and End-user maintainable. Liquid connections, ¼ ½ & 1, DIN Flange & PT Threaded Connections. Also available with NPT threaded and ANSI flange connections. TC-X152TT-FL TC-X050TT

NOTES Registered Names &Trademarks Looped C is a registered Trademark of YTS Co Ltd. SPILLSTOP, SENTRY & SENTINEL are registered trademarks of Blacoh Fluid Control. ONE-UP is a registered trademark of Garlock. Hytrel is a trademark of E.I. du Pont de Nemours and Company. Kynar is a registered trademark of Arkema. Nordel is a trademark of DuPont Dow Elastomers. Ryton is a trademark of Chevron Phillips Chemical Company. Santoprene is a registered trademark of Monsanto Co. Teflon is a trademark of E.I. du Pont de Nemours and Company. Viton is a registered trademark of DuPont Performance Elastomers. TPX is a registered trademark of Mitsui Chemicals. Changes Due to our continued commitment to product improvement, new models, model specifications and prices may change without notice. Product Availability Options, Variations Add On s and Accessories may not be available for all models sizes or materials. For information about the full Line Up, Prices, Availability and Delivery please contact your Pump Distributor directly. Suitability for application Pumps and accessories listed in this document are available in various sizes and materials. For each application please take extreme care with pump choice and always consider such factors as chemical compatibility of the pump body and internal wetted materials, solids size, abrasion resistance, temperature of the liquid, temperature of the surrounding atmosphere, airline or liquid line pressure etc. For more information on choosing the correct pump, please consult with your pump Distributor directly. International Export Control Please note that certain products listed within this document may be subject to international trade restrictions or trade embargoes and may therefore require an export permit prior to dispatch. Products may also require an export licence for reexport from any particular country. For more information regarding international export control regulations please contact Iwaki or contact your local authorities directly.