Bid results for purchase and delivery of Two (2) QuadAxle Plow Equipment Packages-2018 To be installed by Waupaca County Winning Bidder Monroe Truck Equipment Dump Body: 17' 6" inside length x 84" inside width Sloping one piece sides 57" to 50" 100% welded throughout All mounting hardware included Manufacturer build/installation instructions included Cut oval holes rear facing for S/T/T, reverse, and strobes Cut round holes in side for botton style marker lights Provide provision for prewet hoses to pass through long sills from side mounted tanks Install Quick Silver liner per specifications Foldable stainless ladder Side and Front Side to floor radius shall be a minimum of 43" to accommodate side mounted brine tanks 3/16" 304 stainless steel Rear corner post to be made of 3/16 304 stainless steel Rear bolster to be made of 1/4" stainless steel Stainless steel is to remain unfinished(do not paint) Intregal, continuous weld, dirt shedding top rail(no add on angle iron) Full fenders integrated into body made of 3/16" 304 stainless Fabricated 1/8" 304 stainless fender covers per specifications Tailgate Tailgate to be 50" high Tailgate shall be sloped forward 12" and include an asphalt tail Integral dirt shedding peaked top and braces 3/16" 304 stainless steel panel with two horizontal braces 1" thick upper tailgate hinges with 1" pins all made of stainless steel 3.5" tubular perimeter 304 stainless steel structure 3/4" thick flame cut lower latch finger made of stainless steel Open/close air trip cylinders mounted inside corner posts with access panel 3/8" grade 70 spreader chains All tailgate hardware both above and below the floor to be stainless steel Floor and Understructure 1/4" 201 Stainless steel floor Western style crossmemberless understructure 14" high formed longsills made of 1/4" 201 stainless steel welded 100% Cabshield Shall extend a minimum of 22" forward of bulhead made of 7 ga 304 stainless steel Installed by Vendor Miscellaneous Cougar DC3200 electric operated vibrator, factory mounted to underside of body Incl Aero 575 electric tarp system with side mt power pack spring assembly w/alum encl & tension bow Four (4) tow hooks On Spot tire chains per specifications Box height limiting mercury switch control Box up mercury switch
Hoist NTEA class 120 rating 32 ton minimum capacity at 2000 psi Trunion mount design Single acting cylinder with a minimum of 6" bore Rear hinge assembly shall be greasable with removable pins Two (2) OSHA approved body safety props Front Mounted Plow Truck Portion plow Hitch Hitch shall be low profile Receiver boots to allow the hook-up of a jaw style hitch Plow hook-up must interchange with all plows in fleet 4"x10" double acting lift cylinder with nitirde rod Powder coated or painted black 12' x 55" dual compression trip, power reversible 100% welded construction throughout Moldboard Deep C Style made of 10 ga A569 steel Cutting edge 3/4"x8" made of 1080 steel attached with 5/8" dome head plow bolts Must include integral shield Bottom angle to have 11/16" punched holes to match cutting edge Two compression trip assemblies with 3.5" x 1/5" mechanical slide Springs are made from 5160H steel, 3/4" diameter Compression spring brackets designed so that a 10 degree attack angle on the cutting edge is possible 12" rubber snow deflector with steel mounting strap bolted to top angle Reverse Table and Push Frame One piece structural angle semi-circle 35-degree moldboard swing Push frame attached to moldboard with four (4) 1.25" stress proof plated pins Reversing cylinders are located under the semi-circle Positioning of cylinders designed to almost eliminate side stress to the rods Two (2) 3"x10" double acting reverse cylinders with 2" nitride rods Include cushion valve Abrasion resistant hydraulic hoses Hoses are 1/2" ID rated to 3000 psi working pressure and 12000 psi burst pressure Jaw-style quick hitch attached to push frame Screw adjustable parking jack attached to push frame Preparation and Paint The entire plow assembly shall be shot blasted to remove scale, rust, ect. Powder coat or paint, moldboard school bus yellow, push frame black
Single Rear Mounted Partol Wing-RH Side 10' double function design wing All welds to be 100% continuous welds Moldboard Tapered moldboard 3/16" thick Open back design, box formed moldboard not acceptable Moldboard height; 29" toe, 39" heel Pusharm and Trip Assembly Full trip design with torsion spring at the front and extension spring at the rear Heel cylinder plumbed with hydraulic lock Quantity of two (2) 3" diameter heavy-duty push arms Front Head Assembly Front head assmebly must be a parallel link design 3" x 10" double acting cylinder with nitride rod Wing lock to be incorporated into both hydraulic cylinders to prevent drift Mount constructed from 4"x6" tubing and include side plates Rear Mount Shall be constructed from 4"x6" tubing with side plates to be mounted off side of truck frame Preparation and Paint The entire wing assembly shall be shot blasted to remove scale, rust, etc. Powder coat or paint moldboard school bus yellow, hardware black Under Tailgate Spreader Constructed of 304 stainless steel Right or left discharge with dual 18" UHMW spinner assemblies Assembly shall all be 3/16" with 1/4" endplates Mounting brackets are to be 304 stainless steel and bolted to side of box All seams are continuously welded Full width auger located below dump body floor Full opening unobstructed bottom clean out has three (3) solid hinges Auger to have 5/16" x 9" flighting with a 6" pitch Auger shaft is supported by heavy-duty 1-1/2" sealed, self-aligning, greasable 4-bolt flange bearing Spinner assembly is easy one-man mount and dismount Two anti-siphon plates, 18" in length Provide 100 pulse auger feedback sensor integrated into auger sensor Left hand spinner positioned in a manner that it can be seen from the rear view mirror Custom stainless side shields made to fit body to prevent salt from running out sides Custom fabricated stainless auger sensor cover with provisions for lights Liquid Pre-Wet System Two 270-gallon poly tanks with stainless steel hardware designed to fit radius on outside of body Provide on/off output to trigger a 12V gravity feed prewet system with feed line in auger trough Tanks plumbed complete by vendor
Underbody Scraper The moldboard shall be 1" thck x 15" in height, heat treated carbon steel 12' in length The reversing table shall be a 1" solid one-piece circle w/infinite plowing postions, available to 45 deg Reversing will be accomplished with two 4" double acting cylinders Cylinders will provide a hydraulic lock for holding the moldboard in place while in use A cross over relief valve shall be furnished The cylinder rods shall be 2" in diameter and be treated with the Socatri rust preventative treatment The cylinder shall be mounted with 2" pivot pins The greasable rev. circle shall pivot around a 5" cs. center pin and be attached with (3) 3/4" bolts The shape of the hold down blocks should follow the contour of the circle Located underneath the hold down blocks shall be a piece of 3/8" UHMW wear plate The hanger brackets shall be one piece, solid 3/4"x18"x26", A36 mild steel Hanger brackets designed to allow scraper to be infinitely adjustable up/down each side Hinge line shall be a solid shaft, 96" in lenghth and have three moldboard anchor points Hinges are to be bolted to the moldboard an the the hanger board Welded hinges are not acceptable 3 heavy duty greasable hinges located to minimize stress.inner hinge includes plate to prevent shifting Moldboard actuation will be accomplished by two 3-1/2 double acting cylinders w/2" nitrided rods Canister cylinders w/4 hole bolt flange. Cylinders mounted in shock housings trunion mounted 3/4 brkt Trunion bearings 2-3/4x.344 wall carbon steel, lubricated by 2 grease zerks per cylinder, 1 on cyl head Cushioning of moldboard accomplished w/2 heavy duty shock assemblies w/internally mtd springs Pressure relief provided and set to 400psi. Hyd stainless tubing used for ease of mount block maint. Equipped with 15 point remote grease manifold All hardware and fasteners shall be electronically plated and corrosion resistant Complete scraper to be shot blasted, washed and finished black Central Hydraulic System The hydraulic system shall be a transmission mounted, load-sense system PTO/Pump PTO shall be a Chelsea 890 series hot shift design PTO Pump shall be a Force America modek TV092 pressure compenstated piston pump Oil Reservoir/Fuel Tank/Valve Enclosure Combo Mounte Behind cab Entire combo shall be made of 201 or 304 stainless steel 40 gal pass side oil res w/ baffles,bskt style fill/brth,magnetic drain plug,2" suction port w/scrn,sight ga Integrated valve enclosure shall have removable two sided, lockable cover for easy access to valve In-tank 10-micron return filter with condition gauge mounted in the reservoir Separate return line port for the pump control drain line Hot oil, low oil, and body up lights will display in spreader control Integrated fuel tank to be 120 gallon, FMVSS certified with 3" minimum diameter fill cap Fuel tank to included Artic Fox F-407 in-tank fuel and fluid warmer with by-pass thermostat Sending unit for fuel level matched to chassis gauge ohm rating and a certification label An internorman high pressure filter shall be installed before control valve Dimensions of combo unit shall be no more than 18.5" deep x 43" tall x 80" wide
Valving Hyd control valve U.S manufacturer, electrically activated load-sensing valve,manifold design Valving required per bid specification All connectors inside the hydraulic valve/electronic control junction box to be supplied intregal w/sys. Connectors shall be weather tight threaded into a potted weather tight panel All connectors labeled w/appropriate desc. For ea. Connection to individual solenoids of hyd act. Cyl Plow/Wing/Hoist/Scraper Control Force America CommandAll single control or Force America I-Grip single joystick control I-Grip Floor mount control tower Scraper curl function with auto-raise in reverse Summer mode function works in conjunction with I-Grip disabling all functions except hoist & vibrator Control input to allow hoise raise limit mercury switch Electric Spreader Control Force America 6100 Spreader control Provide GPS antenna and plow up/down sensor Precise Air Road Climate temperature sensor w/display readout in spreader control Unit Numbers Unit numbers are to be welded on each significant component prior to painting Manuals Parts and service manuals included. Warranty Warrenty statements must be included with bid for each significant component provided Delivery Date Delivery date determined by bidder and indicated on proposal Performance Bond Successful bidder required to deposit a certified check or performance bond per bid specifications
Two (2) Quad Axle Plow Equipment Packages Proposed Price Each $128,120 Optional Equipment-Additional Cost-Per Truck Provide additional LH wing assembly, components, and controls $11,839 Provide hydraulic lift tailgate, components, and hardware per specifications $2,632 Total Cost for One (1) Quad Axle Chassis Equipment Package with Hydraulic Tailgate Option $130,752 Total Cost for One (1) Quad Axle Chassis Equipment Pkg. with Hydraulic Tailgate and LH Wing Options $142,591 Total Cost for Two (2) Quad Axle Chassis Equipment Packages $273,343 Delivery Date: 180 days after receipt of order Bidder Name: Monroe Truck Equipment Representative: Troy Redfearn Address: 1151 West Main Ave DePere,WI Phone: 920-360-4446 Email: tredfearn@monroetruck Date: