FOR Diesel Power Plant (Doosan-MAN 9L21/31) DATE REVISION : November 2015 : 0 Head Office & Changwon Plant 18, Gongdan-ro 21beon-gil, Seongsan-gu, Changwon City, Kyeongnam, 642-370, South Korea Power Plant Business Team Phone : + 82 2 519 5884 Fax. : + 82 2 519 5919 E-mail : This document is the property of Doosan Engine Co., Ltd. on Republic of Korea(hereinunder referred to as "Doosan"), and is to be used only for the purpose of tendering. Any part of this document should not be reproduced or handed over to third party without the prior written permission of Doosan.
TABLE OF CONTENTS 1.0 INTRODUCTION 2.0 CODES AND STANDARDS 3.0 GENERAL SPECIFICATION 4.0 PERFORMANCE DATA 5.0 SCOPE OF SUPPLY 6.0 DESCRIPTION OF DIESEL GENERATING SET 2 / 7
1.0 INTRODUCTION This technical specification has been prepared by using proven technology and engineering experience of DOOSAN Engine Co., Ltd for the type of Diesel Generator unit proposed. The Diesel Generator unit shall be designed to produce electric power by DOOSAN-MAN ENGINE Type 9L21/31 manufactured by Doosan Engine, Co., Ltd. (Herein after DSE). The technical specification provides the Client with basic and conceptual design information. The technical data herein stated and/or attached is therefore subject to change except guaranteed data during the detailed design stage. 2.0 CODES AND STANDARDS The diesel generating facilities will be designed and manufactured in accordance with the following codes/standards and manufacturer's standards, unless otherwise specified. KS JIS DEMA ISO ASTM ANSI HEI : Korean Standards : Japanese Industrial Standards : Diesel Engine Manufacturer's Association : International Organization for Standardization : American Society for Testing and Materials : American National Standards Institute : Heat Exchange Institute IEC : International Electro technical Commission 3.0 GENERAL SPECIFICATION 3.1 Diesel Engine Description Diesel Engine Type Engine rated output Specification 9L21/31 Remark 1,980 kwm Based on ISO 3046/1 Note: Overload more than 100% load of engine rated output is only allowable during a short time for recovery and prevent of frequency drop at load application. 3.2 Diesel Generating Unit Description Specification Remark No. of DG Unit 1 Electrical output / unit 1,881 kwe Power output measured at the Electrical output / total 1,880 kwe alternator terminal @100% load 3 / 7
4.0 PERFORMANCE DATA 4.1 Reference conditions Stated performances are based on the following "ISO reference conditions" (ISO 3046-1:2002). - Intake air temperature 25 - Barometric pressure 100kPa - Relative humidity 30% - Low calorific value LCV 42,700kJ/kg 4.2 Continuous Power of the Diesel generating unit Continuous power of the generating set @ 100% Load(electrical) 1,881 kwe The above is the electrical output of generating set to be measured at alternator terminals. 4.3 Specific fuel consumption The specific fuel consumption at the reference conditions as per section 4.1 will not exceed the following value: Specific fuel oil consumption 209.25 g/kweh (Without engine-driven pumps, NOx emission according to WB 2007/8:1600mg/Nm 3 @15%O 2 ) 4.4 Adjustment of Engine output & SFOC according to the site condition. Engine output & Specific Fuel Oil Consumption(SFOC) to be adjusted as per the site condition on the basis of Maker's Standard. 4.5 Lubricating oil consumption For the lube oil consumption of one generating set 0.08~0.16 kg/h Above stated value without any losses caused due to cleaning of filter or lube oil charge replacemen 5.0 SCOPE OF SUPPLY Please reference with the EOD_9L2131_Doosan as enclosed 4 / 7
6.0 DESCRIPTION OF DIESEL GENERATING SET 6.1 DIESEL ENGINE 6.1.1 Design and Manufacturing The diesel engine is to be built by DOOSAN Engine Co., Ltd. under license from MAN Diesel. The diesel engine will be manufactured based on the latest design received from the licensor at the date of signing of the Contract. 6.1.2 Principal Particulars of the Diesel Engine Type : In-line, four(4) stroke, direct injection, single acting, trunk piston type with exhaust turbocharger and air cooler Model : Doosan-MAN Diesel 9L21/31 Cylinder configuration : In line Number of cylinders : 9 Cylinder bore : 210 mm Stroke : 310 mm Nominal rating : 1,980 kwm Revolution : 1,000 rpm @ 50Hz Fuel : Heavy Fuel Oil Starting media : Max. 10 bar, Compressed air 6.1.3 Outline Dimension & Weight of Genset Dimensions and weight of the 9L 21/31 engine(for guidance only): A : 5,379 mm B : 2,400 mm C : 7,779 mm W : H : 1,750 mm 3,289 mm Dry Mass : 31 Tons 5 / 7
6.1.4 Detailed Technical Specification 6.1.4.1 General Turbocharged, single-acting four-stroke diesel engine of the trunk piston type with a cylinder bore of 210mm and a stroke of 310mm. The crankshaft speed is 1,000rpm. 6.1.4.2 Fuels The fuel system is designed to operate on the basis of the following fuel oil specifications based on ISO 8217-2010. Diesel fuel oil The usability of DFO depends on its conformity with the key properties listed below; Density at 15 ºC : < 900 kg/m 3 Kinematic viscosity at 40 ºC : 2.0~11 mm 2 /s Pour point, winter quality : < 0 ºC Pour point, summer quality : < 6 ºC Flash point (Pensky Martens) : > 60 ºC Total sediment fraction Water content Sulphur content Ash content Coke residue (MCR) : < 0.1% wt. : < 0.3% wt. : < 2.0% wt. : < 0.01% wt. : < 0.3% wt. Cetane number or cetane index : > 35 Hydrogen sulphide Total acid number : < 2 mg/kg : < 0.5 mg KOH/g Oxidation stability : < 25 g/m 3 Lubricity (wear scar diameter) : < 520µm 6.1.4.3 Cylinder Head The cylinder head is of cast iron with an integrated charge air receiver, made in one piece. It has a bore-cooled thick walled bottom. It has a central bore for the fuel injection valve and 4 valve cross flow design, with high flow coefficient. The valve pattern is turned about 20 to the axis and achieves a certain intake swirl. 6.1.4.4 Valves The valve spindles are made of heat-resistant material and the spindle seats are armoured with welded-on hard metal. All valve spindles are fitted with valve rotators which turn the spindles each time the valves are activated. The turning of the spindles ensures even temperature levels on the valve discs and prevents deposits on the seating surfaces. 6 / 7
6.1.4.5 Cylinder liner The cylinder liners, made of special centrifugal cast iron, are encased by a nodular cast iron cooling water jacket in the upper section. This is centered in the crankcase. The lower section of the cylinder liner is guided in the crankcase. The so-called top land ring fits on the top of the cylinder liner. 6.1.4.6 Piston The piston, which is oil-cooled and of the composite type, has a body made of nodular cast iron and a crown made of forged deformation resistant steel.it is fitted with 2 compression rings and 1 oil scraper ring in hardened ring grooves. 6.1.4.7 Turbocharging system The turbocharger system of the engine, which is a constant pressure system, consists of an exhaust gas receiver, a turbocharger, a charge air cooler and a charge air receiver. The turbine wheel of the turbocharger is driven by the engine exhaust gas, and the turbine wheel drives the turbocharger compressor, which is mounted on the common shaft. The compressor draws air from outside through the air filters. 6.2 GENERATOR 6.2.1 General Manufacturer : Hyoseung Type of excitation : Brushless excitation Parallel operation : Yes Applicable standard : IEC standard 6.2.2 Rating Time rating : Continuous Rated output : 1,881 KW / 2,350 KVA Rated voltage : 6,600 V Rated speed : 1,000 rpm Rated frequency : 50 Hz Number of phase : 3 Number of pole : 6 Power factor : 0.8 Lagging Efficiency at 0.8 pf : 95 % at full load 6.2.3 Specifications Insulation class (all) : F Temperature rise (all) : F Cooling method : Air cooled Protection degree : IP 23 Rated Voltage regulation : ± 10% 7 / 7