UCAR DIVISION RULES AND REGULATIONS. Version UCAR2018a Effective

Similar documents
UCAR DIVISION RULES AND REGULATIONS

2018 UCAR Rules. May 14, 2018

2015 Pure Stock/UCAR Rules

2018 Renegade/V8 Extreme Rules

SOUTH BUXTON RACEWAY LTD BOMBER RULES

2018 BLUE RIDGE MOTORSPORTS PARK RULEBOOK STREET STOCK

2015 Hornet Rules. Evergreen Speedway, Monroe, WA. (Updated 12/05/2014)

Outlaw Figure 8 Rules

2018 FWD Compact Rules (pending)

MINI STOCK RULE BOOK 2019 This is a protest Division No Radios Raceeivers are mandatory!

U-CAR Rules GLASS: All glass & lexan removed. Screen or 4 bars or both in front of driver. 5. WEIGHT: Must weigh 2450lbs

CYLINDER TRUCK RULES

EAGLE VALLEY SPEEDWAY - JIM FALLS, WI HORNET RULES

"2015" Super Tuner & Youth Tuner Rules

2018 SEASON PURE STOCK DIVISION

2019 STOCK 8 ENDURO RULES

SANDUSKY SPEEDWAY 2017 HOBBY STOCK RULES

GLADIATOR RULE BOOK 2017 UPDATED: (Red and Underlined changes)

STREET STOCK & CYCLONES COMBINED RULES

ENDURO Division 2016 RULES AND REGULATIONS

ENDURO 4-6 Cyl Division 2015 RULES AND REGULATIONS

2018 Stinger 8 Rules

Natural Bridge Speedway Official 2016 Rules All-American

2019 Mini Stock Rules. Table of Contents

2012 Pro Stock Rules

2018 CHARGER DIVISION RULES

SOUTHERN OREGON SPEEDWAY Hornets 2013

THE INTERPRETATION OF THESE RULES WILL BE SOLELY THE JUDGMENT OF THE TRACK OFFICIALS & TECH STAFF IN CHARGE AND THEIR DECISION WILL BE FINAL.

300-Lap Ironman Factory Stock Car Enduros

2018 Hornet/Youth Hornet Rules Evergreen Speedway, Monroe, WA (Updated 11/13/2017)

2017 FWD FOUR CYLINDER Rules

2016 DIRTcar Sport Compact TO ALL COMPETITORS/PARTICIPANTS

OFFICIAL MINI MODIFIED DIVISION RULES

Other model rear wheel drive cars are restricted to a maximum 3.8 litre motor and may not lock the rearend.

2014 Outlaw Figure Eight Rules

SOUTH SOUND SPEEDWAY

1.2 NO MITSUBISHI, 3000 GTS, STEALTHS, TURBOS OR SUPERCHARGERS ALLOWED. CHRYSLER PRODUCTS PERMITTED. No convertibles or two seat coupes.

SANDIA SPEEDWAY 2018 STREET STOCK DIVISION RULES

I-96 Speedway Cylinder Rules

Larry King Law s Langley Speedway 2018 Super Street Division Rules

2018 Skid Plate Car Rules

PETALUMA SPEEDWAY SUPER STOCK RULES Current as of April 1, 2016

! 2018 COMPETITION RULES!

Tri-City Bomber Stock Rules 2017 Season

Section 10 Mini Stocks

Coos Bay Speedway HORNET RULES

Claremont Speedway 2015 Wildcat rules

RULE BOOK DISCLAIMER DIXIE SPECIAL EVENT PONY RULES

2018 DAUGHERTY SPEEDWAY SCRAPPER

RULE BOOK DISCLAIMER

2018 Mini Stock Rules

2018 Barberton Speedway Front Wheel Drive Rules

2012 Roadrunner Rules

Plymouth Township Fire Rescue. Tilbury Station. Tuff Truck. Rules

2018 COMPETITION RULES! BOMBERS DIVISION

Tri-City Bomber Stock Rules 2019 Season

2019 Super Street Class Rules. All drivers are required to have their own Raceivers for one-way communication with race director official.

2019 MINI STOCK RULES

1. American made automobile steel, aluminum or rubber glass bodies are allowed as long as they follow original body lines.

I-96 Speedway Street Stock Rules

2017 UPDATE 3/6/17 Thunder Car Rules

2018 Lebanon I-44 Speedway Charger Rules

2018 Vintage Car Rules

ELIGIBLE MODELS Chevy C-10 GMC 1500 Dodge Ram Ford F-150

MOTOR MOUNTAIN MASTERS 4 CYINDERS RULES

2018 BLUE RIDGE MOTORSPORTS PARK RULEBOOK CRATE LATE MODEL

Stock Class Rules 2018

2017 ECMS Super Street Division Rules

2016 RED CEDAR SPEEDWAY OFFICIAL HORNET RULES

SOUTHERN OREGON SPEEDWAY 2177 SOUTH PACIFIC HWY MEDFORD, OREGON (541) / DWARF LITE RULES 2009

Bilstein Modified Lite STARS JR Mod Lites Cup

Super Stock Figure Eight Rules

RACECEIVERS MANDATORY: TRANSPONDERS MANDATORY: IT IS THE DRIVERS RESPONSIBILITY TO HAVE THEM IN WORKING ORDER TO RACE AT THUNDERBIRD RACEWAY.

2018 Mini Sport Rules

4 Banger TECHNICAL RULES

2018 Bomber Rules. The rules listed below are now being enforced and are to be added into the rule book

North Central Arkansas Speedway, LLC

Scotia Speedworld Thunder Car Division Rules 2017 SCOTIA SPEEDWORLD THUNDER CAR RULES 2017

SEEKONK SPEEDWAY SPORT FOUR 2015 EVENT GUIDELINES & REGULATIONS & RULES

2018 Fun Stock Rule Book

Rules. Mud Bog. 1. Class/Category Description. Plymouth Township Fire Rescue Tilbury Station

Thunder Valley Speedway (TVS) 2018 Hobby Stock Rules

2017 A AND B GROUP TECH REQUIREMENTS

2017 Sportmod (B Mod) Rules

Bombers Class 2018 Official Rules and Regulations

PROSTOCK CLASS. Infraction of rules will be decided by Race Officials. Number Plate

AND 6 CYLINDER GUT AND GO RULES

Natural Bridge Speedway Official 2016 Rules Pure Stock

PRO-4 MODIFIEDS 2017 RULES

2016 HOBBY STOCK DIVISION RULES

RACECEIVERS MANDATORY: TRANSPONDERS MANDATORY: IT IS THE DRIVERS RESPONSIBILITY TO HAVE THEM IN WORKING ORDER TO RACE AT THUNDERBIRD RACEWAY.

Grundy County Fair Old School Figure 8 Rules

* 2019 (NEW DIVISION) PURE STOCK RULES *

OCEAN SPEEDWAY. 4 Banger TECHNICAL RULES Updated

All drivers must have working race radios in order to compete. Scoring Transponder is optional for 2015 but will be mandatory for 2016

PURE MINI STOCK CLAIMERS 2008

Mud Bog RULES /6 - v8 - superstock / modified / super modified / x or open class mega truck

2014 Stock Figure Eight Rules

SOUTH SOUND SPEEDWAY

2018 East Coast Mini Stock Tour Rules Last Updated (Jan 20, 2018)

Transcription:

RULE BOOK DISCLAIMER The rules and/or regulations set forth herein are designed to provide for the orderly conduct of racing events and to establish minimum acceptable requirements for such events. These rules shall govern the condition of all events, and by participating in these events, all participants are deemed to have complied with these rules. NO EXPRESSED OR IMPLIED WARRANTY OF SAFETY SHALL RESULT FROM PUBLICATIONS OF OR COMPLIANCE WITH THESE RULES AND OR REGULATIONS. They are intended as a guide for the conduct of the sport and are in no way a guarantee against injury or death to a participant, spectator, or official. The race director shall be empowered to permit reasonable and appropriate deviation from any of the specifications herein or impose any further restrictions that in his/her opinion does not alter the minimum acceptable requirements. NO EXPRESSED OR IMPLIED WARRANTY OF SAFETY SHALL RESULT FROM SUCH ALTERATION OF SPECIFICATIONS. Any interpretation or deviation of these rules is left to the discretion of the officials. Their decision is final.

UCAR DIVISION RULES AND REGULATIONS Version UCAR2018a Effective 11.30.17 The Dominion Raceway UCAR division is designed to promote a greater interest in Stock Car Racing at the least cost possible. Participation in this division allows drivers and teams to learn track procedures, racing manners, and have FUN. All cars must be stock in every way except for modifications allowed by these rules in the interest of safety. The word STOCK means as it came from the factory for the particular make, model and year for a car. In some respects, this philosophy is a throwback to NASCAR stock car racing as it started in 1949. Any reference to NASCAR LMSC rule or section within these rules refers to the current NASCAR Rule Book. These rules are subject to amendment at any time when notice has been given. Notice shall be deemed effective within two (1) weeks of the rule amendment and posting of the rule change by Dominion Raceway (DR). No modifications will be allowed that are not listed in these rules. If in doubt, don t do it. The minimum age for competing in the UCAR division is 14 years old. Proof of age eligibility may be required. 1. Competing Car Models 1.1Any American sub-compact front wheel drive (FWD) ONLY, four cylinder engine, 1972 or newer, car, with a maximum wheelbase of 105-inches, is approved for competition by DR. No convertibles, sports cars, trucks, vans, station wagons, rear wheel, four- wheel drive, rear-steer, rear-engine or mid-engine allowed. No turbocharged, supercharged cars allowed. 1.2Any Import sub-compact front wheel drive (FWD) ONLY, four cylinder engine, 1972 or newer, car, with a maximum wheelbase of 105-inches, is approved for competition by DR. No convertibles, sports cars, trucks, vans, station wagons, rear wheel, four- wheel drive, rear-steer, rear-engine or mid-engine allowed. No turbocharged, supercharged cars allowed. 2. General Body requirements 2.1.Car body must be stock as from the manufacturer for the make, model and year of car. Factory structure must be unaltered. 2.2.No aftermarket spoilers, wings, air dams or body panels are allowed.

3. Detailed Car Body Requirements 3.1.Windshield: Full front original equipment windshield in stock location is required. Windshields maybe replaced with 3/16 inch thick Lexan. Plexiglass is NOT allowed. Three steel support braces, one (1) inch wide by 1/8 inch thick may be installed on the inside of the windshield. Braces must be bolted at one end to the roof and the other end to the dash/firewall area. Braces should not obstruct driver s vision. 3.2.Rear window must be removed. All other OEM glass (except windshield) must be removed. Side glass may be replaced with 3/16-inch Lexan. 3.3.Window Net: Window Net in compliance with NASCAR LMSC rule 20F-3.2.3A must be installed. Window net must be tight when installed and latched. Seat belt latch is not accepted to secure the window net. 3.4.Headlights, taillights, side marker lights, backup lights and exterior side or chrome trim must be removed. 3.5.Rear view mirror inside car is required. OEM mirror is permitted. Wink 3- panel mirror is permitted. Exterior side mirrors are allowed. If removed, the resultant openings may be covered with sheet metal. Covers may not have openings for any purpose. 3.6.Interior trim, carpet, headliner, side panels must be removed. All stock OEM seats front and rear must be removed. An approved racing seat must be installed for the driver. 3.7.Dashboard is required, stock unit or fabricated dashboard allowed. Starter button or switch is optional. 3.8.Fire Walls: Must have full firewalls, front and rear of driver s compartment. Front and rear firewalls must not be altered or moved, and must be in the stock location for the make, model and year car. Firewalls must be sealed with no holes between engine compartment and driver s compartment. Floorboard must remain intact. 3.9.Driver s door must be welded shut. Passenger doors must be welded or bolted shut. Driver s door may have inner metal panel removed only to provide clearance for NASCAR style door bars that extend into the door area. 3.10.Fenders, quarter panels and rocker panels must be stock. No cutting of fenders is allowed. Front inner fender wells may be removed, all other front inner

structure must remain intact. 3.11.Hood must retain stock hinges and must be secured with a minimum of two hood pins in the front. All under hood insulation must be removed. No metal may be removed from the hood and no holes may be cut into hood. 3.12.Roof must be stock and in stock location. 3.13.Rear deck lid must retain stock hinges and must be secured with two hood pins. No metal may be removed from the deck lid and no holes may be cut into deck lid. 3.14.Bumpers must be OEM for that car. No reinforcement is allowed 3.15.Identification and Markings: See DR rules for ALL Divisions section 2. Car number must be displayed in five-inch high, white characters, in the upper right corner of the windshield. Car number must be displayed on the center of both doors in 18 high numbers. Car number must be displayed on the roof in 24 high numbers. Any car that arrives for an event with an unapproved number may be required to change the number before being allowed to participate in the event. 4. General Engine Requirements 4.1.Engine must be stock for the make and model car. Engine number must be correct for make and model car and will be checked. Chevy Cobalts will be allowed but must run the Chevrolet Cavalier approved motor. 4.2.No nitrous oxide or other combustion enhancing products or systems are allowed. 4.3.No dual overhead cams engines allowed. 4.4.The maximum engine cranking compression, when HOT, will be 200 psi. 4.5.DR tech staff will ensure car is no more than 180 degrees as measured by water temp. Engine will be cranked until maximum compression is reached. 4.6.Must have 16 inches of vacuum at 850 RPM. 5. Detailed Engine Requirements 5.1.Engine must remain OEM stock as it came from the factory, including all sensors. No modifications or high-performance parts permitted. 5.2.Carburetor or fuel injection system must be stock for the make and model of car. 5.3.Air filter housing must not be modified in any way and must be functional. This includes the ducting that leads to the filter housing. The filter element must be an OEM style paper element. No high-performance air filter elements. The air filter may not be sprayed with any chemicals or liquids. No cold air intakes permitted.

5.4.Any accessories such as A/C compressor, lines and condenser coil, smog parts, power steering, heater core, etc. may be removed. 5.5.Electric cooling fans are permitted and may be wired to run continuously. 5.6.Antifreeze is not allowed in the cooling system. A $200 fine will be issued if found in car. See DR rules for ALL Divisions section 4. 5.7.Exhaust system must exit behind the driver. Free flow mufflers are allowed. Catalytic converter may be removed. Aftermarket headers are not allowed. Cars must not exceed a 99-db decibel level, as measured by track officials. Sound levels may be monitored anytime cars are on track. Cars determined to exceed track noise limits will be required to modify the exhaust to reduce noise to acceptable levels. 5.8.Computer must be OEM stock for make, year, model and engine size of car. No aftermarket chips and no modifications permitted. 6. Electrical 6.1.Battery must be either securely mounted in a battery box behind the driver s seat or located in the stock location. Battery may not be located in the trunk. 6.2.Transponders All transponders shall be mounted 72 inches, plus or minus 2 inches from the edge of the front bumper, measured from the center of the car. 7. Drivetrain 7.1.Automatic or manual transmission allowed. Transmission/Transaxle must be stock for make and model car. Must be OEM equipment, no aftermarket or highperformance parts allowed. 7.2.Locked transaxle is not allowed. Posi-Traction Transaxle is not allowed. 7.3.No car will be allowed to compete if the transmission is leaking fluid. 8. Wheels and Tires 8.1.Wheels must be a 14 inch steel with a maximum width of seven (7) inches. All four wheels must be the same size, width and offset. 4 back spacing per wheel only. 8.2.The track assigned tire for the UCAR division is the American Racer tire. These are the ONLY tires allowed. 8.3.No tire treatment of any kind is permitted. No camber cutting or alteration of tires is allowed.

9. Frame and Suspension 9.1.Frame and suspension must be stock OEM. No modifications are allowed. 9.2.One (1) spring rubber per wheel. Adjustable spring seats are not allowed. Spring rubbers must be wire-tied in place. 9.3.Stock OEM shocks or OEM replacement shocks only. No racing shocks. 9.4.The camber and caster adjustment plates and mechanisms must be stock. Maximum 5-degree front camber permitted. 9.5.Non-adjustable OEM replacement track bar permitted. 9.6.Replacement parts must be stock equivalent. No high performance suspension parts are allowed. 9.7.Ride height: 5-inch minimum for nose, rocker and frame with driver in car. 9.8.No traction control of any type permitted. 9.9.Stock Dodge Caravan hub is allowed on the right rear only on any model. 10. Steering Components 10.1.Steering components must be stock for the make, model car. 10.2.Steering column must be stock. Steering locking mechanism must be disabled. 10.3.Stock steering wheel may be used if airbag is removed. 10.4.Steering wheels may be equipped with a metal quick release coupling. 11. Brakes 11.1.Stock brakes required at all four wheels. Must be in good working order. 12. Fuel 12.1.Fuel: Pump gas may be used, or racing fuel purchased at Dominion Raceway. 13. Fuel Cell 13.1.The racing fuel cells is highly recommended. If the stock gas tank is factory installed ahead of the rear axle it may be used and must run less than 1/2 full. 13.2.If the stock gas tank is factory installed in behind the rear axle, it must be removed and replaced with a fuel cell or plastic boat tank, maximum capacity eight (8) gallons. Fuel cell/boat tank must be securely mounted on inside, top of the trunk floor, centered and as far forward as possible, with four (4) steel straps. Trunk floor may not be cut or removed. Fuel cell must be covered by 20-gauge sheet metal. Sheet metal panel may be hinged to provide access to fuel cell/boat tank.

13.3.Ford inertia fuel shutoff switch may be removed. 14. Driver Safety Equipment and Roll Bars 14.1.Helmet must meet Snell SA-2005 requirements. See DR rules for ALL Divisions section 6. 14.2.A five-point driver restraint harness is required. See DR rules for ALL Divisions section 6. Belts must be no more than 5 years old. 14.3.Driver s seat must be bolted to the roll cage. Must use a minimum six 3/8 grade 8 bolts. Four on the sides and two on the back of the seat. See DR rules for ALL Divisions section 6. 14.4.A minimum 2 ½-pound fire extinguisher with a dial must be located within reach of belted driver. See DR rules for ALL Divisions section 6. 14.5.Flame retardant driver s suit, neck collar, gloves and shoes are REQUIRED. A HANS-type head and neck restraint device is highly recommended. See DR rules for ALL Divisions section 6. 14.6.Roll bars: A four-point roll cage is required as a minimum. The current NASCAR rulebook should be used as a guide in construction of the roll cage. Roll cage must be fabricated using round 1.750-inch diameter by.090-inch minimum wall thickness seamless steel tubing. Roll cage must have three left side door bars, that must be curved and extend into the door. As a minimum X-bracing must be installed between the main roll bar leg and the front cage leg. An additional, fourth door bar may be installed below the required three and may be straight or curved. The right side door area will have as minimum X-bracing installed between the main roll bar leg and the front cage leg. Additional bars to brace and reinforce the cage are permitted. These additional bars are not allowed to pass forward of the front firewall. The four legs of the cage must each be welded to a 3 x 3 x 3/16 thick steel plate. This plate must be bolted through the floor pan to another 3 x 3 x 3/16 thick steel plate with a minimum of four bolts. Bolts used must be a minimum of ½ diameter grade 8 hardware. Plates may be welded to car as well. Flat steel plates may be replaced by 3 x 3 x 3 x 3/16 thick angle steel. Angle plates if used may be bolted and /or welded to the rocker panels of the car. 14.7.All roll bars within the driver s reach must be covered with roll bar padding. Hi- density, flame resistant, SFI 45.1 approved impact padding is highly

recommended. 14.8.It is highly recommended but not required that an additional one (1) piece one eighth (1/8) inch thick magnetic steel plate must be installed over the outside of the driver s door bars. This plate shall cover the entire driver s side door area and must be welded to the outside of the door bars of the roll cage. Attachment using bolts and/or rivets will not be allowed. Holes of any kind will not be allowed. The plate shall be one piece, if possible. Due to roll cage construction, a multi part plate may be used only with prior approval of track officials. 15. WEIGHT 15.1.Weight rule: Minimum 2,350-lbs. total weight. Minimum 1,060-lbs. right side with driver in car. All bracing must be of equal length and thickness right to left side. No gas or liquids may be added at conclusion of race. 15.2 Added weight must be in block form of no less than 5-pound blocks (no pellets) and painted white with the car number on it. Refer to General Track Rules 1-1.3 Added weight must be securely bolted in place. 15.4 Weight may not be added to the outside of the frame rails or ahead of the front spindles or behind the rear axle or inside the driver s compartment. 15.5 Dislodged weight will not be returned to the car for weighing after the race. 16. General Rules for UCAR division 16.1. The top three finishers in a UCAR feature will start last in the next UCAR feature. This could be the second of twin races or the race the next weekend, whichever comes first. The top three finishers will still practify like normal and if they happen to qualify in one of the top positions, those three cars will be removed and the next cars will move forward in the line-up before the redraw. We will then do the redraw to set the balance of the field. The line-up of the three cars at the rear of the field will be reverse order of how they finished in the previous race. 16.2. Two-way radios are permitted. 16.3. No protests will be accepted in the UCAR division. 1. Fair Competition Rule. 17.1. Fair Competition: In the interest of Fair Competition track officials may add/subtract weight or make other adjustments as necessary to level the competition.

18 Administration 18.1. All competitors should read/review sections 1 thru 17 of the NASCAR 2017 Rule Book or latest edition. 18.2. All competitors should read/review DR General Rules and ALL Division Rules. 18.3. Any questions concerning these rules should be directed to a member of the DR technical crew. 18.4. Dominion Raceway welcomes all of its competitors to an exciting new racing season. Well wishes are extended for a safe, professional and successful racing season. 19. Where in conflict, DR track rules take priority over all other written rules including the NASCAR rule book. ***These rules are for use at Dominion Raceway and Entertainment only. No unauthorized use, reproduction, publication, or printing allowed for any other raceway without the expressed written consent of Dominion Raceway and Entertainment management.