Gleason - JDC & JDCII Series Conductor Bar Systems Features: SAFE, COMPACT AND EASILY ASSEMBLED SINGLE ENCLOSURE H CONDUCTOR ALUMINUM WITH STAINLESS STEEL INSERT INSTALL WITH OR WITHOUT INSULATORS VERTICAL OR HORIZONTAL INSTALLATION 00 V AC / 00 V DC WORKING VOLTAGE 100% DUTY RATED AMPACITIES SINGLE BOLT ANCHORING WATER AND DUST RESISTANT ENCLOSURES -25 TO 85 C (-13 TO 185 F) Applications: STEEL MILLS SHIPBUILDING INDUSTRIAL PLANTS POWER PLANTS WAREHOUSES CONTAINER PORTS Gleason Reel Corp. 00 S. Clark St. Mayville, WI 53050 PH 920-387-4120 www.hubbell-gleason.com
JDC JDCII ALUMINUM ALUMINUM MODEL NUMBER RATED CURRENT RAIL LENGTH MAXIMUM SPEED/MIN. HANGER SPACING BAR SPACING CL TO CL EXPANSION JOINT ENCLOSURE M (FT) M (FT) M (FT) MM (IN) M (FT) MM (IN) JDC150 150 (19.7) 300 (984) 1.2 (3.94) (3.15) 100 (328) 18 x 25.2 (.7 x 1) JDC200 200 (19.7) 300 (984) 1.2 (3.94) (3.15) 100 (328) 24 x 31.5 (.78 x 1.24) JDC250 250 (19.7) 300 (984) 1.2 (3.94) (3.15) 100 (328) 24 x 31.5 (.78 x 1.24) JDC320 320 (19.7) 300 (984) 1.8 (5.9) (3.15) 100 (328) 32.5 x 42.5 (1.28 x 1.7) JDC450 450 (19.7) 300 (984) 1.8 (5.9) (3.15) 100 (328) 32.5 x 42.5 (1.28 x 1.7) JDC00 00 (19.7) 300 (984) 1.8 (5.9) (3.15) 100 (328) 32.5 x 42.5 (1.28 x 1.7) JDC0 0 (19.7) 500 (140) 2 (.5) (3.15) 100 (328) 32.5 x 42.5 (1.28 x 1.7) JDC1000 1000 (19.7) 500 (140) 2 (.5) (3.15) 100 (328) 32.5 x 42.5 (1.28 x 1.7) JDC1250 1250 (19.7) 500 (140) 2 (.5) (3.15) 100 (328) 32.5 x 42.5 (1.28 x 1.7) JDC1500 1500 (19.7) 500 (140) 3 (9.84) (3.15) 100 (328) 44 x 57.5 (1.73 x 2.2) JDC10 10 (19.7) 500 (140) 3 (9.84) (3.15) 100 (328) 44 x 57.5 (1.73 x 2.2) JDC2400 2400 (19.7) 500 (140) 3 (9.84) (3.15) 100 (328) 44 x 57.5 (1.73 x 2.2) JDCII150 150 (19.7) 400 (1312) 1.5 (5) 50 (1.97) 100 (328) 27 x 23 (1.0 x.90) JDCII200 200 (19.7) 400 (1312) 1.5 (5) 50 (1.97) 100 (328) 27 x 23 (1.0 x.90) JDCII250 250 (19.7) 400 (1312) 1.5 (5) 50 (1.97) 100 (328) 27 x 23 (1.0 x.90) JDCII320 320 (19.7) 400 (1312) 1.5 (5) 50 (1.97) 100 (328) 27 x 23 (1.0 x.90) JDCII450 450 (19.7) 400 (1312) 1.5 (5) 50 (1.97) 100 (328) 27 x 23 (1.0 x.90) JDCII30 30 (19.7) 00 (198) 2 (.5) 50 (1.97) 120 (394) 39 x 52 (1.53 x 2.04) JDCII0 0 (19.7) 00 (198) 2 (.5) 50 (1.97) 120 (394) 39 x 52 (1.53 x 2.04) JDCII1000 1000 (19.7) 00 (198) 2.5 (8.2) 50 (1.97) 120 (394) 39 x 52 (1.53 x 2.04) JDCII1250 1250 (19.7) 00 (198) 2.5 (8.2) 50 (1.97) 120 (394) 39 x 52 (1.53 x 2.04) JDCII1450 1450 (19.7) 00 (198) 3 (9.84) 50 (1.97) 120 (394) 39 x 52 (1.53 x 2.04) JDCII10 10 (19.7) 00 (198) 3 (9.84) 5 (2.55) 120 (394) 48 x 0 (1.89 x 2.3) 2
Hanger / Anchor: Insert the Conductor Bar ampacity into the blank space to determine the final Model #. Add: "A" at the end of the Model number for the Anchor Model #. (Example: JDC-250-X for a 250 amp Hanger Bracket / JDC-250-XA for a 250 amp Anchor Bracket) M Size (mm) A B C M Applicability JDC- -X A B 19 2.5 10 8 150A ~ 200A 25 29 12 8 200A ~ 320A 33 40.4 14.2 10 320A ~ 1250A C 45 5 18 10 1250A ~ 2400A JDCII- -X v M C Size (mm) Applicability A B C M 17 20 28 8 150A ~ 450A B v A 48 41 5 8 30A ~ 1450A 0 50 74 10 100A ~ 1450A Mounting Brackets: 51 51 51 51 51 51 25 50 32 10.5 L 4 Model L (mm) JDS-40 40 JDS-535 535 JDS-10 10 25 Gleason Reel Corp. 00 S. Clark St. Mayville, WI 53050 PH 920-387-4120 www.hubbell-gleason.com 3
COLLECTOR ASSEMBLY MODEL NUMBER RATED CURRENT SHUNT SIZE APPLICABLE BAR SIZE MAXIMUM SPEED M/MIN (FT. MIN.) COLLECTOR HEAD MOVEMENT CONNECTOR ARM TO BAR WEIGHT SINGLE SHOE JDC-150C 150 1 mm2 JDC 150, 200, 250 500 (140) ± / ±40 250 mm (10") 2.2 kg (4.85 lbs.) JDC-150C2 150 x 2 1 mm2 JDC 150, 200, 250 500 (140) ± / ±40 250 mm (10") 2.2 kg (4.85 lbs.) JDC-250C 250 25 mm2 JDC 250, 450 500 (140) ± 100 / ±40 300 mm (12") 2.8 kg (.17 lbs.) JDC-250C2 250 x 2 25 mm2 JDC 450, 00 500 (140) ± 100 / ±40 300 mm (12") 2.8 kg (.17 lbs.) JDC-0C 0 50 mm2 JDC 00, 1200 500 (140) ± 100 / ±40 300 mm (12") kg (13.22 lbs.) JDC-1250C 1250 70 mm2 JDC 0, 2400 500 (140) ± 100 / ±40 300 mm (12") 8 kg (17.3 lbs.) Joint Clamp: JDC E Size (mm) A B C D E M Applicability 18 100 25 5 25 M8 <200A 22 100 31 25 M8 200A ~ 250A 29 10 40 5 40 M10 320A ~ 450A 29 10 40.5 40 M10 00A ~ 0A M C D 29 10 40 9 40 M10 1000A ~ 1250A 40 1 0 12 45 M14 1500A ~ 2400A B A 40 1 0 14 45 M14 >2400A JDCII Size (mm) A B C D M Applicability 1 100 9 25 M8 150A ~ 450A 35 10 17 40 M10 30A ~ 1450A 45 175 35 40 M12 100A ~ 3000A Gleason Reel Corp. 00 S. Clark St. Mayville, WI 53050 PH 920-387-4120 www.hubbell-gleason.com 4
Joint Clamp Cover: Insert the Conductor Bar ampacity into the blank space to determine the final Model #. Add: "L" at the end of the Model number for the Joint Clamp Cover Model #. *NOTE: For the JDCII, the model number will be JDCII-250-L and for the JDU, JDU-250-L. *JDC- -L End Caps: Insert the Conductor Bar ampacity into the blank space to determine the final Model #. Add: "D" at the end of the Model number for the End Cap Model #. *NOTE: For the JDCII, the model number will be JDCII-250-D and for the JDU, JDU-250-D. *JDC- -D Gleason Reel Corp. 00 S. Clark St. Mayville, WI 53050 PH 920-387-4120 www.hubbell-gleason.com 5
Maintenance Section: The following is a suggested connection of the maintenance section. Terminal points must be separate when wiring the Maintenance Section. Do not connect any Power Feed directly to any bolt on the Maintenance Section. This will cause failure and risk of injury. below: Device on the maintenance section Maintenance section (spacing section) Power Point Power Point Power Point 2,500 1,000 2,500 Maintenance section (spacing section) *JDC- -MS Expansion Section: 38 11.5 SN Specification Code unit Qty. Remark MAINTENANCE SECTION 1 JDC-150 1111 AMPACITY 2 JDC-200 1112 SPACING RATING 3 JDC-250 1113 20-30 mm 150-200 4 JDC-320 1114 20-30 mm 200-320 5 JDC-450 1115 30-50 mm 320-1250 JDC-00 111 30-100 mm 7 JDC-0 1117 1250-2400 8 JDC-1000 1118 Insert the Conductor Bar ampacity into the blank space to determine the final Model #. Add: "MS" at 9 JDC-1250 1119 the end of the Model number for the Maintenance Section Model #. 10 JDC-1500 111810 *NOTE: For the JDCII, the model number will be JDCII-250-MS and for the JDU, JDU-250-MS. 11 JDC-10 111811 Thermal 12compensation JDC-2400 section (Thermal 111812 expansion section) 1 JDCII-150 Thermal 1211 compensation section 2 JDCII-200 1212 (Thermal expansion section) 3,000 3 JDCII-250 1213 4 JDCII-300 1214 5 JDCII- 450 1215 JDCII-30,000 121 SN Specification 7 Code JDCII-0 unit 1217 Qty. Remark 1 JDC-150 8 111701 JDCII-1000 1218 EXPANSION JOINT 2 JDC-200 9 111702 JDCII-1250 1219 AMPACITY 3 JDC-250 10 111703 JDCII-1450 121810 SPACING RATING 4 JDC-320 1 111704 JDU-250 2111 30-50 mm 150-200 5 JDC-450 2 111705 JDU-320 2112 30-90 mm 200-320 JDC-00 3 11170 JDU-450 2113 13 13 4 JDU-00 2114 28 7 JDC-0 111707 28 30-90 mm 320-1250 3 3 8 JDC-1000 5 111708 JDU-0 2115 30-90 mm 1250-2400 9 JDC-1250 111709 JDU-1000 211 Insert the 10Conductor JDC-1500 Bar ampacity 7 111710 into JDU-1250 the blank space 2117 to determine the final Model #. Add: "ES" at the end of the Model number for 8 the Expansion JDU-1500 Section 2118 Model #. 11 JDC-10 111711 *NOTE: 12For the JDC-2400 JDCII, the model 9 111712 number JDU-10 will be JDCII-250-ES 2119 and for the JDU, JDU-250-ES. 1 JDCII-150 10 121701 JDU-2400 211810 Gleason Reel Corp. 2 00 JDCII-200 S. Clark St. 11 121702 Mayville, JDU-3200 WI 53050 211811 PH 920-387-4120 www.hubbell-gleason.com 3 JDCII-250 12 121703 JDU-300 211812 *JDC- -ES 4 JDCII-300 121704 38 11.5
J Shanghai Pubang mechanism and electric manufacture co., Ltd. (D) Drawing for mounting and main parts: 1. Drawing for mounting modes: Mounting Methods: CONDUCTOR BARS Shanghai Pubang mechanism and electric manufacture co., Ltd 30 30 240 50 >200 120 120 120 30 Method Mode one: The insulated conductor rails are mounted The insulated Method conductor Mode three: two: rails The are This mounted insulated mounting with conductor method insulators is rails on applicable four are lines mounted for horizontally high voltage (adjustable sup on four lines horizontally (fixed support) This mounting (3kV mode and on is below) three applicable lines and outdoor horizontally for the HV insulated insulated (fixed aluminum support) conductor bar rail enclosures. and spacing the out insulated aluminum alloy enclosure (3000kv below). Mounting Bracket: 10 (200) 2. Drawing for parts: 1. Terminal cover, 2. Double-pole current collector, 3. Conductor rail joint, 2.0 Spacing 4. Suspender, 5. Conductor rail and enclosure,. Power supplier 50 2150 (750) 000 3000 (1500) (100) 000 000 3000 (1500) 1500 (750) 50 30 (100) (100) (100) >200 BK-L4 30 (100) (100) General Arrangement: 1 2 3 4 Mode three: The insulated conductor rails are mounted Note: the size Insulated in the brackets conductor is applicable rails are for mounted 150~320A. otwo upper and on four lines horizontally (adjustable support) two lower lines horizontally (fixed support) 3. Joint device: 30 (100) 1. End Cap 2. Collector Assembly 3. Bar Connector and Cover 4. Hanger/Anchor 5. Conductor Bar. Cover w/ Power Supply to Bar Connector 5 1 2 3 4 5 7 1 30 2150 (750) 000 3000 (1500) >550 000 000 3000 (1500) 1500 (750) >550 4 2 3 (55) (55) 30 (100) (100) Note: the size in the brackets is applicable for 150~320A. 1. Clamp, 2. Conductor rail, 3. bolt, 4. Connector, 5. Conductor rail enclosure,. Copper terminal, 7. Power supply cable Mode four: The insulated conductor rails are mounted The insulated conductor rails are mounted on one upper and on three lines horizontally (adjustable support) three lower lines horizontally (fixed support) No. 0 Jinfu Road, Baoshan District,Shanghai PRC E-mail:liushi@pubang.sh.cn http://www.pubang.sh 18 No. 0 Jinfu Road, Baoshan District,Shanghai PRC E-mail:liushi@pubang.sh.cn http://www.pubang.sh.cn 1 2 3 4 5 Gleason Reel Corp. 00 S. Clark St. Mayville, WI 53050 PH 920-387-4120 www.hubbell-gleason.com 7
APPLICATION & PRODUCT PHOTOS Gleason Reel Corp. 00 S. Clark St. Mayville, WI 53050 PH 920-387-4120 FAX 920-387-4189 www.hubbell-gleason.com JDCB1114