ROFU For Outswing Doors Installation Instructions for Slide Mount Magnetic Locks 8606, 8608 and 8612 Series *See page 2 for model specifications R Find the paper installation template included with the magnet (you will need this). Fold it on the dotted line. The rubber washer helps the armature plate to pivot s it should NOT be tightened all the way to door. Place the folded template in the proper position on the door/jamb and mark the holes you will cut for your magnet and armature plate. (Using tape will help) Adjustable Attach the mounting plate with the provided Phillips screws. Then the position of the mounting plate should still be adjustable. (Sample drawing as 8612 series mounting plate) Drill the holes according to the marks you made. Wiring 4 (Check Twice! Drill Once!).. Install the armature plate as shown in the drawing to the left. Attach the mounting plate to the jamb with included mounting Phillips screws as shown. (Sample drawing as 8612 series magnet & mounting plate) The actual dimensions of the holes are illustrated below. Hollow Metal Door Solid Door Use the Allen wrench and thru-bolts to tighten the magnet to the mounting plate. 1 7/16 Allen Wrench 1/2 5/16 1/2 5/16 Drill a 5/16 (8mm) hole through the door for the armature side. For the sexnut side (secure side), enlarge the hole to 1/2 (12.7mm) for the width of the sexnut. On wood doors the depth of the sexnut is 1 7/16 (36mm). Outswing Door Connect the power and test the holding force. Add washers if there is still a gap between the magnet and armature plate. Wires (Sample drawings above as 8612 series magnet & mounting plate) (1) Pass the wiring through the mounting plate and into the wiring hole at the top of the magnet and into the PCB area. (2) Slide the magnet onto the mounting plate. (3) Once into proper position, tighten the thru-bolts from the bottom of the magnet into the mounting plate using the included Allen wrench. Allen Wrench 1
ROFU Z-bracket for Inswing Doors 1 2 3 4 Find the correct mounting position on the door jamb for the L-bracket. Ensure that the door still closes with it in position. Use the thru-bolt to install the magnet onto the L-bracket. Assemble the Z-bracket, but not too tight as it needs to remain adjustable for now. Insert the roll pins into the armature plate. 5 6 7 Finish Outdoor Outdoor Attach the armature plate and washers to the Z-bracket assembly. Specifications Close the door and connect the power. Voltage: 12/24 VDC Selectable Current Draw: 500 ma /12VDC, 250 ma / 24VDC Holding Force: 600 lbs, 600lbs, 800lbs, 800lbs, 1200 lbs, 1200 lbs Dimensions: 8606-B/BD: (600 lbs) Magnet: 9 13/16" 13/16" " (250 5.5 5mm) : 7 1/4" 1/2" /2" (185 x 38 2mm) 8606-2-BD: (600 lbs ) Magnet: 19 11/16" 13/16" " (500 5.5 5mm) s (each side): 7 1/4" 1/2" /2" (185 x 38 2mm) 8608-LC/B/BD: (800 lbs) Magnet: 10 7/16" 1/16" 1/8" (265 2 9mm) : 7 1/4" 3/4" x 9/16" (185 5 4mm) 8608-2-B/BD: (800 lbs ) Magnet: 20 7/8" 1/16" 1/8" (530 2 9mm) s (each side): 7 1/4" 3/4" x 9/16" (185 5 4mm) 8612-LC/B/BD (1200 lbs) Magnet: 10 1/2" 13/16 " 9/16" (267 x 71 0mm) : 7 1/4" 3/8" /8" (185 x 616mm) 8612-2-B/BD: (1200 lbs ) Magnet: 21" 13/16" 9/16" (533 x 71 0mm) s (each side): 7 1/4" 3/8" /8" (185 x 616mm) After the magnet engages the armature plate, you can now adjust the Z-bracket, and attach to the door. Ensure all screws of Z-bracket are tighten to door. We encourage the use of thread locker (LocTite). Model Changes to ROFU ic Locking Devices 86 XX - 2 - (LC/BD/B) - (US28/40)(12/24) Holding Force: 06 = 600 lbs (Mini) 08 = 800 lbs (Midi) 12 = 1200 lbs (Standard) Functions: LC = Low cost (NO MONITORING) BD = Bond sensor, LED & Door status B = Bond sensor & LED only 2 = Double Magnet OR NOTHING THERE 6 = Slide mounting plate magnetic lock series MAGLOCK SERIES 12/24: 12/24 VDC Selectable Finish: US28 Satin Aluminum or US40 Duronatic / Dark Anodized Bronze (Limited Availability for US40) 8600 Series Diagrams of Magnets & Mounting s 8606-B, 8606-BD 8608-LC, 8608-B, 8608-BD 8612-LC, 8612-B, 8612-BD (600 lbs.) (800 lbs.) (1200 lbs.) 8606-2-BD 8608-2-B, 8608-2-BD 8612-2-B, 8612-2-BD (600 lbs. ) (800 lbs. ) (1200 lbs. ) 2
Wiring Diagram for 8606 and 8608 Series Single Magnet Models Supply PB contact output: Open / Not bonding status. contact output: Locked / Bonded status. Keypad/Reader Orange: White: Brown: Indicates the door is in and open or closed status. Reed switch rated 0.2A/12VDC supply Input For 8608-LC Wiring Wiring Diagram for 8612 Series Single Magnet Models supply PB Keypad/Reader contact output: Open / Not bonding status. contact output: Locked / Bonded status. Indicates the door is in and open or closed status. Reed switch rated 0.2A/12VDC Orange: White: Brown: supply For 8612-LC Wiring Input Voltage Selection Jumpers - ROFU recommends a good maintenance schedule! - Please ensure all armature bolts and mounting bolts are checked quarterly. - ROFU recommends using Loctite (Thread locker) on ALL bolts during installation. - Current Draw: 500 ma /12VDC, 250 ma / 24VDC per block 3
Wiring Diagram for 8606-2-BD and 8608-2-BD Double Magnet Models Supply PB contact output: Open / Not bonding status. contact output: Locked / Bonded status. Keypad/Reader Orange: White: Brown: Indicates the door is in and open or closed status. Reed switch rated 0.2A/12VDC Orange: White: Brown: Wiring Diagram for 8612-2-B/BD Double Magnet Models Supply PB Keypad/Reader contact output: Open / Not bonding status. contact output: Locked / Bonded status. Orange: White: Brown: Indicates the door is in and open or closed status. Reed switch rated 0.2A/12VDC Orange: White: Brown: 4
Installation Diagram & Screw Pack Components (Sample drawings of 8606-B & 8612-2-B magnet & assemblies) Mounting Mounting Cover Screw Screw Mounting Screw Mounting Screw Cover Components 8606-B 8608-B 8612-B 8608-LC 8612-LC 8608-2-B 8612-2-B Thru-s (5/32"5/32") (1/4" 21/32") (1/4" 21/32") Phillips Flat Head Screws (5/32" ") (11/32" 9/32"/32") (11/32" 9/32"/32") 0 0 Allen Flat Head Screw (5/16" 3/8") (5/16" ") (5/16" 3/8") (5/16" ") (5/16" 3/8") Hexagon Key (Allen Wrench) (1/8") (1/2" 9/16") (1/2" 9/16") 5
Installation Diagram & Screw Pack Components (Sample drawings of 8606-BD & 8606-2-BD magnet & assemblies) Mounting Mounting Cover Screw Screw Screw Mounting Screw Cover Mounting Holder Holder Holder Components 8606-BD 8608-BD 8612-BD 8606-2-BD 8608-2-BD 8612-2-BD Thru-s Phillips Flat Head Screws (5/32"5/32") (1/4" 21/32") (5/32" 5/32") (1/4" 21/32") (5/32" ") x 6 (11/32" 9/32"/32") (9/16" 3/16" /32") 1 1 0 2 2 (5/32" ") 2 (11/32" 9/32" /32") (9/16" 3/16" /32") Allen Flat Head Screw (5/16" 3/8") (5/16" ") (5/16" 3/8") (5/16" 3/8") (5/16" ") (5/16" 3/8") Hexagon Key (Allen Wrench) (1/8") (1/8") (1/2 9/16 ) (1/2 9/16 ) 6