Eye/Face Washes G1778 Eye/FaceFWash,FWallFMountedFAutoFlow F90 FSwing-Down G1778LH-L G1778LH G1778LH-R G1778L G1778 G1778R Units shown in plan view Model G1778LH-L Shown Application: AutoFlow eye/face wash for mounting on wall. Spray heads swing down from storage to operational position, activating water flow. Available in a variety of spray head configurations to minimize obstructions at a sink. Note: If unit is not installed at a sink, floor drain should be provided underneath unit to prevent accumulation of water on floor. Spray Head Assembly: Two FS-Plus spray heads. Each head has a flip top dust cover, internal flow control and filter to remove impurities from the water flow. Valve: 1/2" IPS plug-type valve with O-ring seals. Swinging head assembly down from storage to operational position opens orifice and activates water flow. Unit remains in operation until spray head assembly is returned to storage position. Strainer: Unit is furnished with in-line strainer to protect valve and spray heads from debris in water line. Mounting: Valve is installed in Type 316 stainless steel housing. Mount housing on wall using anchors or other mounting hardware. Construction: Polished chrome plated brass. Supply: 1/2" NPT female union inlet. Sign: ANSI-compliant identification sign. Quality Assurance: Unit is completely assembled and water tested prior to shipment. Available Options TMV G3600LF thermostatic mixing valve precisely blends hot and cold water to deliver tepid water as required by ANSI Z358.1-2014. Refer to Tempering Units section for complete technical and product selection information.
Eye/Face Washes G1778 Eye/Face Wash, Wall Mounted AutoFlow 90 Swing-Down G1778LH-L G1778LH G1778LH-R G1778L G1778 G1778R this space for architect/engineer approval Sign Included Due to continuing product improvement, the information contained in this document is subject to change without notice. All dimensions are ± 1/4" (6mm).
Parts List Swing-Type Eyewashes and Eye/Face Washes Each spray head head features: Tough polypropylene plastic construction Highly visible integrated nylon dust cover Easily accessible 1.8 GPM (GS-Plus ) or 3.2 GPM (FS-Plus ) flow controls. Dense (60 pore per inch) polyurethane filter Unique design provides a consistently soft, full spray of water across a range of working pressures from 30 to 100 PSI Item Part Number Description A AP470-001 GS-Plus Spray Head (assembled) B AP470-002R Dust Cover and Cap Assembly C 470-004R 60 PPI Polyurethane Filter D 470-005R 1.8 GPM Flow Control E AP470-021 FS-Plus Spray Head (assembled) F AP470-022R Dust Cover and Cap Assembly G 470-024R 60 PPI Polyurethane Filter H 470-025R 3.2 GPM Flow Control A E Note: If experiencing any issues with the rotating valve assembly, please contact the factory. B F C G IMPORTANT In order to operate properly, the flow control must be inserted into the body concave end first. D H
Parts List In-Line Strainer To perform weekly cleaning of the strainer: 1. Unscrew the strainer bonnet (a). 2. Inspect the o-ring (b) for for damage. Replace if needed. 3. Remove cylindrical screen (c) and rinse under clean water. Gently rub the screen until all debris has been removed. 4. Carefully reinsert screen into the counterbore within the strainer body (should fit snugly). 5. Replace strainer bonnet and test for proper operation of strainer and eye wash. Important: All emergency equipment must be inspected and tested at least weekly to ensure proper operation. On units equipped with an in-line strainer, weekly inspection should also include checking the strainer for accumulation of debris or foreign matter. Such debris can impair the flow of water through the strainer and prevent the eye wash from functioning properly. AP400-013 In-Line Strainer Assembly A B RK400-013 Repair Kit for Inline Strainer consisting of bonnet, O-Ring and 50 Mesh Cylindrical Screen C
A. EF-30* Wall mounted AutoFlow swivel eye/face wash less bowl with ½ IPS plugtype valve with Teflon coated O-ring seals and stainless steel enclosure. Supplied with in-line strainer to prevent debris from affecting the valve. Unit shall have (2) polypropylene FS Plus spray heads with integral flip-top dust covers, filters and 3.2-GPM flow control orifices mounted on a chrome plated brass eyewash assembly (Specify spray head configuration). Activate valve by rotating 90 from stored position. Unit shall include ANSI compliant sign. B. Performance: Unit shall be fully factory assembled and hydrostatically tested to meet or exceed ANSI Z358.1 2009, and come with a full 2-year warranty. C. Fixture: Guardian Equipment G1778