R IPS RON STL PIP ROOV VLVS 08.0 Vic -300 utterfly Valves PROUT SRIPTION ear Operator 3" with Position andle Vic -300 butterfly valves are designed for pressures ranging from vacuum to 300 PSI (065 kpa). Vic-300 butterfly valves feature a narrow profile disc design with a smooth, coated inner body which combine for superior flow characteristics. This combination results in low break-away torque, reducing gear operator and actuator sizing and costs. Standard polyphenylene sulfide blend (PPS) coating accommodates a wide variety of severe services (epoxy coating or full stainless body are available for severe services). The dualseal disc provides bubble-tight sealing up to 300 PSI (065 kpa) in both directions without added valve modifications or cost. When using Victaulic butterfly valves with flange adapters consult Victaulic. vailable disc coatings include PM for water service to +30 (+110 ) and nitrile for oil services with the option of fluoroelastomer for corrosives and aromatics. The Vic-300 butterfly valve is available with manual handles, gear operators or automated in two-way and three-way configurations. or fire protection services, see Series 708W butterfly valve; refer to Section 10.06. Lever Lock andle TURS 1. ody and isc ore ast of rugged ductile iron for durability and strength.. isc oating isc is encapsulated with various synthetic elastomers to accommodate varied service requirements. 3. ody oating Polyphenylene sulfide blend is heat fused to the entire body. poxy coating is available. 4. ual Seal isc Two molded-in rings assure inner body wiping action and a back-up seal for flow in both directions providing bubble-tight shut-off to 300 PSI (065 kpa). 5. rive ub ast integrally with the disc to provide direct disc drive and allow positive location of the disc. 10 - racket onnections 9 - rooved nds 4 - ual Seal isc 6. ub earing Naval brass (316 stainless available) bearing provides positive hub alignment. 7. Trunnion Naval brass (316 stainless available) trunnion. 7 - Trunnion 5 - rive ub 8. ub and Trunnion Seals O-ring seals (of the same material as the disc coating) provide a secondary shaft seal. 9. rooved nds Permits installation with two Victaulic grooved couplings. 6 - ub earing 8 - ub Seals Primary Seals - isc oating 1 - ody 3 - ody oating 1 - isc ore Primary Seals 8 - Trunnion Seals 10. racket onnections (Vic-300/Series 608) Side-wing connection permits bracket design to accept varied manual or power actuators. Victaulic World eadquarters P.O. ox 31, aston, P 18044-0031 4901 Kesslersville Rd., aston, P 18040 1-800-PIK VI X: 610/50-8817 www.victaulic.com 1471 Rev. 9/00 Registered Trademark Victaulic ompany of merica opyright 1997 Victaulic ompany of merica Printed in U.S..
IMNSIONS Vic-300 utterfly Valves - 3" 4-5" ear Operator 6" 8-1" 3" with Position andle Lever Lock andle - 8" with Locking evice ctual mm - Overall eight Lever Lock/ Inf. Var. andle ear Operator imensions /millimeters Lever Lock/ Inf. Var. andle ear Operator 08.0-1 prx. Wgt. ach Lbs. kg.375 3.1 5.61 5. 1.5 3.53 3.53.38 1.69 1.78 3.7 50 60.3 8 14 133 39 90 90 60 43 45 1.7 ¹ ₂.875 3.77 6.11 5.7 1.80 3.9 3.9.88.5.31 4.1 65 73.0 96 155 145 46 100 100 73 57 59 1.9 3 O.. 3.000 3.77 6.11 5.7 1.80 3.9 3.9 3.0.5.31 4.8 76.1 76.1 96 155 145 46 100 100 77 57 59. 3 3.500 3.77 6.75 6.36.14 4. 4. 0.08 3.50,59.31 4.8 80 88.9 96 171 16 54 107 107 89 66 59. 4 00 4.63 9.03 9.5.71 5.15 5.8 0.07 5.88 3.19.79 10.5 100 114.3 118 9 35 69 131 134 149 81 71 4.8 5 5.563 5.88 9.94 10.17 3.1 5.67 5.80 0.43 5.88 3.70 3.9 14.0 15 141.3 149 53 58 79 144 147 11 149 94 100 6.4 5¹ ₂ O.. 5.500 5.88 9.94 10.17 3.1 5.67 5.80 0.43 5.88 3.70 3.9 14.0 139.7 139.7 149 53 58 79 144 147 11 149 94 100 6.4 6 6.65 5.88 10.89 1.05 3.61 6.15 6.94 1.00 7.50 4.16 3.96 19.0 150 168.3 149 77 306 9 156 176 5 191 106 101 8.6 6¹ ₂ O.. 6.500 5.88 10.89 1.05 3.61 6.15 6.94 1.00 7.50 4.16 3.96 19.0 165.1 165.1 149 77 306 9 156 176 5 191 106 101 8.6 8 8.65 5.33 13 14.44 5.00 7.93 7.93 1.8 10.0 5.50.67 41.0 00 19.1 135 369 367 17 01 01 33 59 140 68 18.6 10 10.750 6.40 17.0 16.67 5.94 8.68 8.68 1.7 1.0 6.69 30 59.0 50 73.0 163 437 43 151 1 1 44 310 170 81 6.6 1 1.750 6.50 19.64 19.11 7.07 10.00 10.00.63 14.5 8.00 3.5 85.0 300 33.9 165 499 485 180 54 54 67 36 03 83 38.6 Stainless steel body also available. See Section 17.05 for details. or 14-4" (355.6-609.6 mm) butterfly valves, refer to 08.03. Large diameter 14-4" (355.6-609.6 mm) butterfly valves are available rated to 300 PSI (065 kpa). ontact Victaulic for details. NOT: Vic-300 valves in 6-1" (168.3-33.9 mm) sizes are not recommended for use in dry compressed air services. ontact Victaulic ngineering Services for recommendations. 08.0 -
IMNSIONS Lever Lock/ Infinitely Variable andle L L K min. (0" extended) J J OPN SUT K - 8" Sizes 10-1" Sizes SUT ctual mm imensions /millimeters prx. Wgt. a Lbs./kg J K L 4.0 7.13 1.70 1.5 60.3 107 181 43 0.7 ¹ ₂ 4.0 7.13 1.70 1.5 73.0 107 181 43 0.7 3 4.0 7.13 1.70 1.5 88.9 107 181 43 0.7 4 6.88 10.50.50 1.5 114.3 175 67 64 0.7 5 6.88 10.50.50 1.5 141.3 175 67 64 0.7 6 7.10 1.00.50 1.5 168.3 180 305 64 0.7 8 8.88 16.00.50 19.1 5 406 64.0 10 7.13 11.66 7 1.0 73.0 181 96 116 5.4 1 7.13 11.66 7 1.0 33.9 181 96 116 5.4 NOTS: andles for - 8" (60.3-19.1 mm) valves come complete with hardware for both variations. 10 and 1" (73.0 and 33.9 mm) equipped with infinitely variable handle only. 08.0- Two-Position andle K ctual mm nd to nd imensions /millimeters Overall gt. K 08.0-3 prx. Wgt. a. Lbs. kg 3.1 4.07 1.5.06.38 1.43 6.56. 60.3 8 103 39 5 60 36 167 1.0 ¹ ₂ 3.77 5.30 1.80.40.88 1.46 6.81.9 73.0 96 135 46 61 73 37 173 1.3 3 3.77 5.39.14.40 0.08 3.50 1.46 6.81 3.6 88.9 96 137 54 61 89 37 173 1.6 08.0-3
IMNSIONS ear Operator S T N 1 N J P O 1 K L M Q O R dia. N hain Wheel Option imensions /millimeters Nom. In. ctual andwheel hain Wheel mm J K L M N 1 O 1 N O P Q R S T 5.19 9.5.38 1.13 4.00 7.09 4.00 9.5.19 0.38 0.63 5.00 1.83 No. Turns to lose 08.0-4 prx. Wgt. ach Lbs./kg 60.3 13 35 60 9 101.6 180 10 35 56 10 16 17 46 7.0 ¹ ₂ 5.19 9.5.38 1.13 4.00 7.09 4.00 9.5.19 0.38 0.63 5.00 1.83 73.0 13 35 60 9 101.6 180 10 35 56 10 16 17 46 7.0 3 5.19 9.5.38 1.13 4.00 7.09 4.00 9.5.19 0.38 0.63 5.00 1.83 88.9 13 35 60 9 101.6 180 10 35 56 10 16 17 46 7.0 4 5.19 9.5.38 1.13 4.00 7.09 4.00 9.5.19 0.38 0.63 5.00 1.83 114.3 13 35 60 9 101.6 180 10 35 56 10 16 17 46 7.0 5 5.19 9.5.38 1.13 4.00 7.09 4.00 9.5.19 0.38 0.63 5.00 1.83 141.3 13 35 60 9 101.6 180 10 35 56 10 16 17 46 7.0 6 5.19 9.5.38 1.13 8.00 7.09 9.00 9.50.19 0.30 0.63 5.00 1.83 168.3 13 35 60 9 03 180 9 41 56 8 16 17 46 7.0 8 5.19 9.5.38 1.13 8.00 7.09 9.00 9.50.19 0.30 0.63 5.00 1.83 19.1 13 35 60 9 03 180 9 41 56 8 16 17 46 7.0 10 5.94 10.78.38 1.13 8.00 8.09 9.00 10.50.44 0.30 0.63 6.00.36 7.0 73.0 151 74 60 9 03 06 9 67 6 8 16 15 60 10 3. 1 5.94 10.78.38 1.13 8.00 8.09 9.00 10.50.44 0.30 0.63 6.00.36 7.0 33.9 151 74 60 9 03 06 9 67 6 8 16 15 60 10 3. *ontact Victaulic for details. ccessories hain wheel and uide hain wheels are mounted to the gear operator handwheels. Sprocket rim and guide arms are made of cast aluminum. hain is galvanized steel. OW TO ORR: Specify type valve and operator by valve numbering system shown on back page. lways specify length of chain required. or insulation and locking device, contact Victaulic for details. ctual mm - 5 Lever Lock with Locking evice imensions /millimeters Sprocket Size hain Wheel Size (ia.) Lever Lock racket Insulation 08.0-5 prx. Wgt. a. Lbs. kg 4.00 4.63 3.5 60.3-141.3 0 10 118 1.6 6, 8, 10, 1 9.00 10.5 10 168.3-33.9 9 67 08.0-4
PRORMN Values values for flow of water at +60 (+16 ) with various disc positions are shown in tables at right. ormulas for Values: P Q = --------- Q = P Where: Q = low (PM) P = Pressure rop (PSI) = low oefficient In. ctual mm (ull Open) In. ctual mm 3 (ull Open) In. ctual mm 5¹ ₂ O.. (ull Open) In. ctual mm 8 60.3 115 88.9 48 139.7 1150 19.1 ¹ ₂ 4 6 10 73.0 35 114.3 600 168.3 1850 73.0 3 O.. 5 6¹ ₂ O.. 1 76.1 35 141.3 1150 165.1 1850 33.9 08.0-6 (ull Open) 3400 5750 8300 08.0-7 ctual mm 60.3 ¹ ₂ 73.0 3 O.. 76.1 3 88.9 4 114.3 5 141.3 5¹ ₂ O.. 139.7 6 168.3 6¹ ₂ O.. 165.1 8 19.1 10 73.0 1 33.9 LOW OIINTS isc Position (egrees open) 90 70 60 50 40 30 0 115 80 40 17 10 5 1 35 160 84 48 7 10 35 160 84 48 7 10 48 196 114 73 44 18 3 600 450 30 148 85 4 3 1150 560 330 10 10 60 15 1150 560 330 10 10 60 15 1850 960 600 380 40 130 45 1850 960 600 380 40 130 45 3400 1910 1170 780 470 60 104 5750 30 1980 130 800 440 180 8300 4650 850 1900 1150 640 50 low haracteristics 6.0/.41 5.0/.34 4.0/.8 3.0/.1 08.0-9 LOW O WTR T 65 (18 ) TROU ULL OPN VLV VI-300 PRSSUR ROP PSI/ar.0/.14 1.0/.07 0.9/.06 0.8/.06 0.7/.05 0.6/.04 0.5/.03 0.4/.03 0.3/.0 "/60,3 mm ¹ ₂"/73,0 mm 3"/88,9 mm 4"/114,3 mm 5"/141,3 mm 6"/168,3 mm 8"/19,1 mm 10"/73,0 mm 1"/33,9 mm 0.3/.01 0.1 0 10 100 300 600 1,000,000 4,000 10,000 0,000 3 68 136 7 454 7 70 4540 LOW RT PM /m 3 h 08.0-5
VLV TORQU RQUIRMNTS Victaulic Vic-300 valves have low torque requirements for operating the valve. This results in less manual effort, smaller gear operators or smaller, less expensive actuators to open and close the valve. The torque data listed below is the highest required to operate the valve at the given pressures in wet service. These torque values are based on extensive testing by Victaulic. These values are for normal wet service only and may vary for dry services or for lubricating fluids. ontact Victaulic for other services. ctual mm Torque Inch Pounds/Newton Meters *ifferential Pressure PSI/ar 50/3 100/7 150/10 00/14 300/1 30 30 50 60 70 60.3 3.4 3.4 5.7 6.8 7.9 ¹ ₂ 50 60 80 95 10 73.0 5.7 6.8 9.0 10.7 13.6 3 O.. 50 60 80 95 10 76.1 5.7 6.8 9.0 10.7 13.6 3 70 90 110 130 170 88.9 7.9 10. 1.4 14.7 19. 4 150 50 50 350 500 114.3 17.0 8.3 8.3 39.5 56.5 5 300 350 350 450 550 141.3 33.9 39.5 39.5 50.8 6.1 6 500 600 700 800 950 168.3 56.5 67.8 79.1 90.4 107.3 6¹ ₂ O.. 500 600 700 800 950 165.7 56.5 67.8 79.1 90.4 107.3 8 1100 1150 100 150 1400 19.1 14 130 136 141 158 10 1550 1675 1800 195 150 73.0 175 189 03 17 43 1 1900 000 175 350 700 33.9 15 6 46 66 305 08.0-8 MTRIL SPIITIONS ody: uctile iron conforming to STM -395, grade 65-45-15, and STM -536, grade 65-45-1 ody oating: PPS Polyphenylene sulfide blend, UL classified in accordance with NSI/ NS 61 for cold +86 (+30 ) and hot +180 (+8 ) potable water service. Optional: poxy isc: uctile iron conforming to STM -395, grade 65-45-15, and STM -536, grade 65-45-1 isc oating: (specify choice) rade PM PM (reen color code). Temperature range 30 to +30 ( 34 to +110 ). Recommended for cold and hot water service within the specified temperature range plus a variety of dilute acids, oil-free air and many chemical services. UL classified in accordance with NSI/NS 61 for cold +86 (+30 ) and hot +180 (+8 ) potable water service. NOT ROM- MN OR PTROLUM SRVIS. rade T nitrile Nitrile (Orange color code). Temperature range 0 to +180 ( 9 to +8 ). Recommended for petroleum products, air with oil vapors, vegetable and mineral oils within the specified temperature range. Not recommended for hot water services over +150 (+66 ) or for hot dry air over +140 (+60 ). Optional: rade O fluoroelastomer luoroelastomer (lue color code). Temperature range for continuous service up to +300 (+149 ). Recommended for many oxidizing acids, petroleum oils, halogenated hydrocarbons, lubricants, hydraulic fluids, organic liquids and air with hydrocarbons to +300 (+149 ). *Services listed are eneral Service Recommendations only. It should be noted that there are services for which these gaskets are not recommended. Reference should always be made to the latest Victaulic asket Selection uide for specific gasket service recommendations and for a listing of services which are not recommended. NOT: When connecting Vic- 300 butterfly valves to Style 741 or Style 743 Vic-lange adapters, please contact Victaulic. rive ub dapter: ot rolled steel, black enamel coated Upper earing/lower Trunnion Seals: Same as isc oating Upper earing/lower Trunnion: Naval brass Optional: Type 316 stainless steel Operator racket: ot rolled steel, black enamel coated racket olts/washers: old rolled steel, zinc plated Operator: (specify choice) - 3" (60.3-88.9 mm) Two-position detent manual handle: ot rolled steel, black enamel coated Manual lever lock/ infinitely variable handle: uctile iron conforming to STM -395, grade 65-45-15, and STM -536, grade 65-45-1 (other parts cold rolled steel, zinc electroplated) includes memory stop. Manual gear operator with handwheel Optional: Memory stop Optional: hain wheel lectric actuator Pneumatic actuator Sizing of actuator is dependent on service. ontact Victaulic for details. 08.0-6
Vic-300 utterfly Valve Numbering System V - 040-3 7 4 11 Type Size V 030 040 060 080 100 10 Pressure Rating ody isc/trim racket Operator 3-300 PSI 3 - poxy coated iron 5 - PPS coated iron 7-316 Stainless Steel 9 - Special* NOTS: () Used with position detent handle only * etails required 1 - una/ronze - PM/ronze 3 - Viton/Stainless Steel 4 - una/stainless Steel 5 - PM/Stainless Steel 9 - Special* 0 - No racket () - Standard 3 - Standard with insulation 4 - UL/M 9 - Special* 00 - are 11 - andle with memory stop 15 - position detent handle (sizes ", ¹ ₂" & 3" only) 0 - ear operator 1 - ear operator with memory stop - ear operator with chain wheel 3 - ear operator with WW square oper. nut 4 - ear operator with memory stop and chain wheel 9 - Non-std. gear operator* VV - Pneumatic* WW - lectric* YY - ydraulic* L - 10 position handle with tamper-proof Locking evice This product shall be manufactured by Victaulic ompany. ll products shall be installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations. 08.0-7