Instruction Sheet P/N 090A Prodigy Mobile Box Unloader System Description The Prodigy Mobile Box Unloader system unloads 5 kg (50 lb) boxes of powder and pumps the powder to spray gun feed hoppers. Systems are available with 5 Vac, 60 Hz or 0 Vac, 50 Hz vibrator motors and include a Prodigy HDLV high-capacity transfer pump. NOTE: For more information on Prodigy HDLV High-Capacity Pump operation and repair information, refer to manual 0970. 6 5 4 7 Figure Prodigy Mobile Box Unloader System Components. Vibrator table 4. Vibrator motor switch box. Prodigy transfer pump 5. Pump purge control. Pickup tube 6. Pump air regulator and gauge 7. Inlet air ball valve
Prodigy Mobile Box Unloader System Installation. Unpack the system.. See Figure. Pull up on the lock knob () and swing the pickup tube arm () out. Release the lock knob to hold the arm in place.. Install the pickup tube () into the collar on the end of the arm. 4. Connect the 6-mm transfer tubing (4) to the pickup tube adapter. 5. Plug the ground wire (9) into the ground socket (8) on the pickup tube. 6. Connect the three leads of the electrical cable (0) to a three-pronged electrical plug or electrical panel. Electrical power supplied to the system must match the vibrator motor rating. 7. Connect a source of compressed air to the / in. NPT ball valve (). 8. Connect the ground cable clamp () to a true earth ground. 5 Vac or 0 Vac L (brown) N (blue) GND (green/yellow) 4 5 6 9 7 0 8 Figure Installation. Lock knob. Arm. Pickup tube 4. Transfer tubing 5. Nut 6. O-ring 7. Adapter 8. Ground socket 9. Ground wire 0. Power cable. Ball valve. Ground cable Note: The pickup tube includes an elbow fitting for fluidizing air. Fluidizing air is not used with this application.
Prodigy Mobile Box Unloader System Pump Output Connection See Figure. 0 meters (00 ft) of 6-mm transfer tubing is included with the system. Connect one end of the tubing to the delivery fitting. Connect the other end to the feed hopper inlet. Purge Air Inlets (Connected to Air Pilot Valve) Conveying Air Pressure 0.7-.0 bar (0-5 psi) Pinch Pressure.4-.75 bar (5-40 psi) Input Air 0-mm tubing 4.8 bar (70 psi) Powder Delivery 6-mm Tubing, 0 m (00 ft) maximum Ground (Connected to Dolly) Powder Suction 6-mm Tubing (Connected to Pickup Tube Figure Pump Connections and Controls Operation WARNING: Input power must match the rating on the switch box label.. Supply electrical power and compressed air to the system.. Lift the pickup tube and place a box of powder on the vibrator table.. Open the box and plastic bag and lower the pickup tube into the powder. 4. Use the bag tie wrap to secure the plastic bag around the pickup tube. NOTE: Fluidizing air to pickup tube is not used with this pump. 5. Turn on the vibrator motor. 6. Open the ball valve to supply air to the pneumatic panel. 7. Adjust the pump air pressure to 4.8 bar (70 psi). This provides an approximately 500 millisecond cycle rate. 8. To purge the pump and the suction and delivery tubing, press and hold the purge button on the pneumatic panel (See Figure ).
4 Prodigy Mobile Box Unloader System Repair Switch Box/Vibrator Motor Connections GROUND INSIDE JUNCTION BOX GND (GREEN/YELLOW) BLUE GND (GREEN/YELLOW) BLUE L (BLUE) L (BROWN) BROWN 5 INPUT POWER 6 TERMINAL BLOCK SWITCH SWITCH BOX WIRING DIAGRAM TO PIN 5 OF TERMINAL BLOCK TO PIN OF SWITCH TO PIN 5 OF TERMINAL BLOCK TO PIN OF SWITCH MOTOR CAPACITOR WHITE WHITE BLACK WHITE BLACK GREEN TO PIN 6 OF TERMINAL BLOCK RED OR BROWN GREEN TO PIN 6 OF TERMINAL BLOCK SWITCH BOX 5VAC, 60Hz VIBRATORY MOTOR CABLE FROM VIBRATORY MOTOR SWITCH BOX CABLE FROM VIBRATORY MOTOR 0VAC, 50Hz VIBRATORY MOTOR Figure 4 Switch Box and Vibrator Motor Connections
Prodigy Mobile Box Unloader System 5 Ground Connections WARNING: Make sure all ground connections are complete and secure. Operating the transfer system without proper grounding is hazardous and could result in personal injury or property damage. Pickup Tube Ground Wire System Ground Cable Vibrator Table/Motor Ground Terminals Pump Panel Ground Stud Ground Wire to Dolly Frame Ground Stud Ground Wire to Pump Vibrator Table Ground Wire Dolly Frame Ground Stud Figure 5 System Ground Connections
6 Prodigy Mobile Box Unloader System Parts To order parts, call the Nordson Finishing Customer Support Center at (800) 4-99 or contact your Nordson representative. Systems Part Description Note 09056 SYSTEM, dolly, 5V VBF/HDLV, Prodigy 09 SYSTEM, dolly, 0V VBF/HDLV, Prodigy System Parts 7 4 6 5A 5 0 6 8 9 Figure 6 System Parts
Prodigy Mobile Box Unloader System 7 Item Part Description Quantity Note 068409 DISCONNECT, hi-cap HDLV pump, w/o mount O-ring 06840 NUT, tube retaining, hi-cap, HDLV pump 944 O-RING, silicone, 0.65 x 0.8 x 0.094 in. 4 068400 MOUNT, pump adapter, w/o O-ring gland 5 076407 KIT, fluidizing, pickup tube, VBF, transfer A NS 07597 TUBE, one piece, fluidizing, pickup, VBF 5A 9485 O-RING, silicone, conductive, 0.875 x.06 in. 6 090 TUBE, polyurethane, 6 mm OD AR 7 90057 TUBING, poly, spiral cut, 0.6 ID AR 8 08596 ISOLATOR, vibration, 0 mm dia x 8 mm studs 9 074467 KIT, service, 5V vibrator motor, w/capacitator B NS 0748 VIBRATOR, electrical, 5V, 60 Hz, w/connector B 9 076854 KIT, service, 0V, vibrator motor, w/capacitator B NS 0748 VIBRATOR, electrical, 0V, 50 Hz, w/connector B 0 0940 PUMP ASSEMBLY, high capacity, generation II, HDLV, packaged 0909 CABLE, power, wire, 6 ft. 404 SWITCH, rocker, DPST, dust-tight 97808 CONNECTOR, strain relief, / in. NPT NS 084 STRAP, Velcro, w/buckle, 5 x cm AR NS 06654 TUBE, polyethylene, 6-mm OD 00 ft D NOTE A: Kit contains tubing and fittings to connect fluidizing air to the pickup tube. These parts are not used in this application and can be discarded. B: Vibrator motor kits contain replacement capacitator, which is installed in the switch box. Refer to Figure 4 for wiring diagram. C: Air tubing, pneumatic control module to pump. D: Powder transfer tubing. 0 m (00 ft) maximum. AR: As Required NS: Not Shown Continued...
8 Prodigy Mobile Box Unloader System Pneumatic Manifold Parts A 0 9 C D B 7 Figure 7 E ITEM NO. 5 6 Pneumatic Control Module Parts 4 Air Supply To Pump TUBING CUT LENGTHS TUBE IDENTIFIER 8 CUT LENGTH ± [.50] A 78 [7.00] B 5 [6.00] C 89 [.50] D 5 [6.00] E 78 [7.00] 4 To Pump Purge Fittings Item Part Description Quantity Note 4 900740 TUBING, polyurethane, 0 mm AR A 5 90074 TUBING, polyurethane, 6/4 mm, blue AR A 6 90068 TUBE, polyurethane, 8 mm OD, blue AR A 7 905 VALVE, ball, / in. NPT 8 90074 VALVE, airpilot, way 9 06455 VALVE, push button, control 0 058680 REGULATOR, / 8 in. NPT, / 4 in. NPT, 7-5 psi 908 GAUGE, air, 0-00 psi, 0-7 kg/cm NOTE A: Order in increments of one foot. AR: As Required Issued 0/08 Original copyright date 008. Prodigy, HDLV, Nordson, and the Nordson logo are registered trademarks of Nordson Corporation.