TUV isted ED Gas Station ights ED STREET IGHTS ED GAS STATION IGHTS
TUV isted ED GAS STATION IGHTS PRODUCT CATAOG Overview The ENETEC H /H5-Series ED Gas Station lights are using UMIEDS UXEON 00 D luminous source, providing excellent lumen output, long-las ng stability and splendid sight. The ENETEC H /H5 -Series ED recessed lights have a high luminous efficiency and be er service life. Provide 7 years warranty on luminaire. Color Op ons Silver Gray ED UMINOUS SOURCE ED DRIVER (Two op ons) + NON-DIMMABE High-end Mean Well HG Series ED driver, op mal stability, performance and lifespan. + DIMMABE High-end programmable ED driver, integrate dimming func on and 6KV /0KV surge protec on. Provide excellent performance and lifespan. ED MODUE Exquisite design with powerful thermal dissipa on and IP67 waterproof performance. Overall stainless steel screws adopted. Black & Silver Color Modules. Cylindrical edge design, avoid lacera on. XTREME UMINAIRE DESIGN Reasonable heat sink design, not only keep ven la on but also avoid lacera on. Gaps between each module increase heat dissipa on speed and solve the problem of dust deposi on.
TUV isted ED GAS STATION IGHTS PRODUCT CATAOG Op cs 80 80 60º 0 0 90º 0 0 90 90 90 90 0 0 0 0 0 0 C0 - C80 C90 - C70 unit: cd C0 - C80 C90 - C70 unit: cd Reference Only ens code: 60º Reference Only ens code: 90º Applica ons: Shelf Aisle High Hall High Workshop Applica ons: Warehouse Workshop 80 0º 0 0 90 90 0 0 C0 - C80 0 C90 - C70 unit: cd Reference Only ens code: 0º Applica ons: Warehouse Workshop Gas Sta on DETAIED FEATURES Professional lens design with, 90 and 0 op onal. Use M6 waterproof connector, avoid hard power damage. The exquisite and innovated frame holder not only makes the installa on more simple but also fi rmer. A special taylor-made packaging designed to guarantee the highest protec on of the lamp. Use waterproof connector for internal wiring, safe, convenient & fast. Innova ve pluggable connector, clean & efficient. Convenient & fast installa on. With a non-corrosive material, not only exquisite appearance, but also no corrosion concerns.
TUV isted ED GAS STATION IGHTS PRODUCT CATAOG Product ENEP-0W-0TUVH ENEP-80W-0TUVH ENEP-0W-0TUVH ENEP-60W-0TUVH Nominal Wa age 0W 80W 0W 60W ED Working Current 95 ma 00 ma 00 ma 00 ma Number of Modules Input Voltage Dimming ED Brand Driver Brand 0-0V 00-0V /77V AC 50 /60Hz 0-5V, 0-0V, PWM, Timer Philips umileds 00 Non-dimmable: MeanWell HG Driver Dimmable: Inventronics Driver Max. Current @ 0V 0.A 0.8A.A.65A Max. Current @08V 0.A 0.7A 0.7A 0.95A Max. Current @0V 0.A 0.A 0.6A 0.8A Max. Current @77V 0.8A 0.6A 0.5A 0.7A Opera ng Temperature Power Factor (PF) THD -0 ºC to +50 ºC >0.95 <0% umen Output (+/- 5%) 500 lm 000 lm 5600 lm 0800 lm uminaire efficacy 0 lm /w 0 lm /w 0 lm /w 0 lm /w Op c CRI CCT Ra ng Material Installa on Accessories (Op onal) Shell Color umen Maintenance Certifica ons Packaging Type, 90, 0 >70 000K (Nature White), 5000K (Pure White), 5700K (Cool White) IP66, IK0 Housing: Die-cast aluminum; Heat sink: Stretched Aluminium Alloy; ens: PC Recessed installa on Mo on sensor Silver (RA90), other RA colors available on request > 75,000 hours-₇₀ at 5 ºC CE, ROHS, M80, ISO900, ISO00 unit /ctn. DIMENSION DATA UMEN MAINTENANCE Number of Modules Ambient Temperature TM- umen Maintenance (5,000 Hours) Theore cal 70 (Hours) ength mm 9. 0 mm.0 77 mm.8 50 mm 7.7 5 ºC 78.05% 8,000. kg 5. lbs..6 kg 8.0 lbs.. kg 9.7 lbs. 5. kg.9 lbs. 0 ºC 78.99% 79,000 6 mm 0 mm. inches.7 inches Hole Size 0 x85 mm 75 x85 mm 8.0 x. 0.8 x. *Ceiling Thickness: 0-5 mm /0. -.0 inches 8 x85 mm.7 x. x85 mm 6.6 x. 50 º C 78.9% 75,000 PACKAGING DATA 65 mm. Number of Modules 00 mm 7.9 ength 80 mm.0 55 mm.0 5 mm 6.7 505 mm 9.9. kg 6.8 lbs.. kg 9.7 lbs. 5. kg.5 lbs. 6. kg.9 lbs.
TUV isted ED GAS STATION IGHTS PRODUCT CATAOG Product ENEP-50W-0TUVH5 ENEP-00W-0TUVH5 ENEP-50W-0TUVH5 ENEP-00W-0TUVH5 Nominal Wa age 50W 00W 50W 00W ED Working Current 5 ma 0 ma 0 ma 0 ma Number of Modules Input Voltage 00-0V /77V AC 50 /60Hz Dimming 0-0V 0-5V, 0-0V, PWM, Timer ED Brand Philips umileds 00 Driver Brand Non-dimmable: MeanWell HG Driver Dimmable: Inventronics Driver Max. Current @ 0V 0.5A.0A.5A.06A Max. Current @08V 0.0A 0.59A 0.89A.9A Max. Current @0V 0.6A 0.5A 0.77A.0A Max. Current @77V 0.A 0.5A 0.67A 0.89A Opera ng Temperature Power Factor (PF) THD -0 ºC to +50 ºC >0.95 <0% umen Output (+/- 5%) 650 lm 500 lm 8750 lm 5000 lm uminaire efficacy 5 lm /w 5 lm /w 5 lm /w 5 lm /w Op c CRI CCT Ra ng Material Installa on Accessories (Op onal) Shell Color umen Maintenance Certifica ons Packaging Type, 90, 0 >70 000K (Nature White), 5000K (Pure White), 5700K (Cool White) IP66, IK0 Housing: Die-cast aluminum; Heat sink: Stretched Aluminium Alloy; ens: PC Recessed installa on Mo on sensor Silver (RA90), other RA colors available on request > 75,000 hours-₇₀ at 5 ºC CE, ROHS, M80, ISO900, ISO00 unit /ctn. DIMENSION DATA UMEN MAINTENANCE Number of Modules Ambient Temperature TM- umen Maintenance (5,000 Hours) Theore cal 70 (Hours) ength mm 9. 0 mm.0 77 mm.8 50 mm 7.7 5 ºC 78.05% 8,000. kg 5. lbs..6 kg 8.0 lbs.. kg 9.7 lbs. 5. kg.9 lbs. 0 ºC 78.99% 79,000 6 mm 0 mm. inches.7 inches Hole Size 0 x85 mm 75 x85 mm 8.0 x. 0.8 x. *Ceiling Thickness: 0-5 mm /0. -.0 inches 8 x85 mm.7 x. x85 mm 6.6 x. 50 ºC 78.9% 75,000 PACKAGING DATA 65 mm. Number of Modules 00 mm 7.9 ength 80 mm.0 55 mm.0 5 mm 6.7 505 mm 9.9. kg 6.8 lbs.. kg 9.7 lbs. 5. kg.5 lbs. 6. kg.9 lbs.
TUV isted ED GAS STATION IGHTS PRODUCT CATAOG Dimming Mul ple dimming func ons are integrated (0-5V DC or 0-0V DC or PWM Signal or Timer). 0-5V Dimming The recommended implementa on of the dimming control is provided below. N G Vac Inventronics ED Driver V+(BRN) V-(BU) Vaux(BK/WHT) Dim+(PUR) Dim-(GRY) 0-5V Dimmer Implementa on : Posi ve logic Notes:. The dimmer can also be replaced by an ac ve 0-5V voltage source signal or passive components like resistors and zener.. Do NOT connect Dim to the output V or V+, otherwise the driver will not work properly.. If 0-5V dimming is not used, Dim + should be open.. When 0-5V nega ve logic dimming mode and Dim+ is open, the driver will output maximum current. Implementa on : Nega ve logic 0-0V Dimming The recommended implementa on of the dimming control is provided below. N G Inventronics ED Driver V+(BRN) V-(BU) Vaux(BK/WHT) Dim+(PUR) Dim-(GRY) 0()-0V Dimmer Implementa on : Posi ve logic Notes:. The dimmer can also be replaced by an ac ve 0-0V voltage source signal or passive components like resistors and zener.. Do NOT connect Dim to the output V or V+, otherwise the driver will not work properly.. If 0-0V dimming is not used, Dim + should be open.. When 0-0V nega ve logic dimming mode and Dim+ is open, the driver will output maximum current. Implementa on : Nega ve logic PWM Dimming The recommended implementa on of the dimming control is provided below. N G Inventronics ED Driver V+(BRN) V-(BU) Vaux(BK/WHT) Dim+(PUR) Dim-(GRY) PWM Signal Implementa on 5: Posi ve logic Notes:. Do NOT connect Dim to the output V or V+, otherwise the driver will not work properly.. If PWM dimming is not used, Dim + should be open.. When PWM nega ve logic dimming mode and Dim+ is open, the driver will output maximum current. Implementa on 6: Nega ve logic
TUV isted ED GAS STATION IGHTS IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precau ons should always be followed including the following: PRODUCT CATAOG READ AND FOOW A SAFETY INSTRUCTIONS... To avoid the possibility of electrical shock, turn off power supply before installa on or servicing. Installa on and servicing should be performed by qualified personnel. Product must be installed in accordance with your local electrical code. If you are not familiar with these codes and requirements, consult a qualified electrician. Do not change the structure or any commponents of the fi xture to ensure safety. 00-0V/77V AC, 50/60Hz, Suitable for Wet oca ons (IP65), Class I *This product must be grounding Model No. ENEP-0W-0TUV Power 0W Dimension x6 x0 mm /9. x. x.7. kg /5. lbs SAVE THIS INSTRUCTIONS FOR FUTURE REFERENCE ENEP-80W-0TUV ENEP-0W-0TUV 80W 0W 0 x6 x0 mm/.0 x. x.7 77 x6 x0 mm/.8 x. x.7.6 kg /8.0 lbs. kg /9.7 lbs ENEP-60W-0TUV 60W 50 x6 x0 mm/7.7 x. x.7 5. kg /.9 lbs TO INSTA: 0W 80W 0W 60W uminaire Frame uminaire Main Body 6mm. inches 6mm. inches 6mm. inches 6mm. inches Ceiling Securing Fi ngs x mm 9. inches Hole Size: 0 85 mm 8.0. inches 0 mm.0 inches Hole Size: 75 85 mm 0.8. inches 77 mm.8 inches Hole Size: 8 85 mm.7. inches 50 mm 7.7 inches Hole Size: 85 mm 6.6. inches Suitable Ceiling Thickness: 0-5 mm /0. -.0 inches MOUNTING Ceiling Panel - Ceiling Panel uminaire Frame STEP : Open the moun ng hole on the Ceiling Panel. (See Figure for opening size) Power Supply Cord Power Cord Remove Ceiling Securing Fi ngs on this side - - Allen Wrench: 6mm (5/ ) Ceiling Securing Fi ngs Ceiling Securing Fi ngs No ce the INSTAATION DIRECTION Allen Wrench: 6mm (5/ ) STEP : Remove TWO() Ceiling Securing Fi ngs of one side, bring the side of uminaire Frame with Ceiling Securing Fi ngs into Ceiling Panel. See Figure -. Bring en re uminaire Frame into Ceiling Panel, Clamp the Ceiling Panel by Ceiling Securing Fi ngs and ghten by 6mm (5/ ) Allen Wrench. See Figure -. Mount the removed Ceiling Securing Fi ngs back to uminaire Frame, no ce that the both sides are opposited. Clamp and ghten by 6mm (5/ ) Allen Wrench. See Figure -. uminaire Main Body Ceiling Securing Fi No ce the INSTAATION DIRECTION ngs STEP : Connect the Power Cord to the supply wiring per Electrical Connec ons sec on for comple ng electrical connec ons.
TUV isted ED GAS STATION IGHTS PRODUCT CATAOG STEP : Tilt and bring the uminaire Main Body into uminaire Frame a er the step of Electrical Connec ons. See Figure 5. uminaire Main Body uminaire Frame 5 6 STEP 5: Place the uminaire Main Body by horizontal onto uminaire Frame, fine tuning and ensure the uminaire Main Body is snapped into to the slot of uminaire Frame. See Figure 6. IMPORTANT Check whether it concerns an AC(Alterna ng Current) based system - 00-0V/77V AC, 50/60Hz. EECTRICA CONNECTIONS - 00-0V/77V AC, 50/60Hz PHASE TO NEUTRA WIRING STEP : Make the following Electrical Connec ons: a. Connect INPUT GROUND conductor to GREEN WIRE posi on of the terminal block or GROUND conductor of ED driver. b. Connect INPUT VOTAGE conductor to BROWN WIRE posi on of the terminal block or INE conductor of ED driver. c. Connect INPUT NEUTRA conductor to BUE WIRE posi on of the terminal block or NEUTRA conductor of ED driver. STEP : Make sure all excess input wires are pushed into pole, screws are ghtened. STEP : Close cover by fi rmly pushing cover towards fixture, making sure that no wires are pinched and Sealing gasket are fully engaged. STEP : If the fixture without a terminal block, please insulate all electrical connec ons with wire nuts suitable for at least 90 C FIXTURE WIRING INPUT WIRING INE BACK GROUND GREEN NEUTRA WHITE TERMINA BOCK(not-provided), Use waterproof connector for wet loca on. G N INE BROWN GROUND YEOW-GREEN NEUTRA BUE AC BASED Input cable should be at least H05RN-F x.0mm²(sjtw 8AWG) or outdoor grade cable with rubber sheathed(not supplied). The cable must have a minimum cross sec onal area of.0mm²(8awg). *If the fi xture with built-in in dimming func on, please connect INPUT POSITIVE(+) signal conductor to DIM+ (BUE WIRE), INPUT NEGATIVE(-) signal conductor to DIM-(WHITE WIRE) of ED driver. ED DRIVER This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collec on systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.