OY Non Handed loser egular rm ee Page eft Hand H ight Hand everse H eft Hand H ight Hand everse H eft Hand H ight Hand everse H ee Page 5 Parallel rm ee Pages & 4 UTION Instructions Trityle 100H eries Non Handed loser n Increctly installed improperly adjusted do closer can cause property damage personal injury. These installation instructions should be followed to avoid the possibility of misapplication misadjustment. "D" suffix (Delayed ction) is an optional feature. separate sheet is supplied showing closer adjustments. NOTE: F special applications a separate do and frame preparation template is packed with these instructions. Use this instruction sheet f installation sequence and closer adjustments only. s should be hung on ball bearing antifriction hinges. separate do stop is recommended. and frame must be properly reinfced. djust closing time speed between and 7 seconds from 90 to 0. These do closers should NOT be installed on the exposed side (weather side) of exteri dos. UTION tronger Hold Open rm Models ized (izes,,4,5,) 10H 101H OY 10H 104H 105H 10H ee Page 5 ight Hand H eft Hand everse H djustable (izes thru ) (izes 1 thru 4) 101FH egular rm ee Page Parallel rm ee Pages & 4 ight Hand H eft Hand everse H elf Drilling crews Wood and Metal ight Hand H eft Hand everse H () leeve Nut and olt pring Power djustment crew 101(F) eries Only "" Valve loser ody #7 Metal 1/40 tandard omponents /1" Wood et crew F Wood drill /1 hole Machine crews #7 Drill, 1/40 Tap rm ssembly Main rm Drill 9/ thru from loser ide /8 Drill other side Thru olt and Grommet Nut Drill 9/ thru from loser ide /8 Drill other ide omponents 188 Plate 14 offit dapter Plate Pinion ap loser ize tamp ""Valve ""Valve 18H offit Plate Used with Parallel rm losers Only over 100P opyright 001, 014 Yale ecurity Inc., an OY Group company. ll rights reserved. eproduction in whole in part without the express written permission of Yale ecurity Inc. is prohibited. 1 809150400 (0514)
100H eries Hold Open rm losers egular rm Parts OY 1 1/4 11/4 () (44) over /4 (19) 91/1 (0) 7/8 () D Y FT eft Hand Nut Down and valves toward hinge ight Hand hown Opening To 100 101 to 10 11 to 180 Dimension "" 7 (178) 1/ (89) /Wall/Hardware/Jamb conditions permitting Inches (mm) F 90 E weep 4 5 atch G P tronger 101(F) Only pring Power djust (If Necessary) ackcheck et Hold Open 7 Pinion ap 8 over tronger 90 min. aution: Don't completely close valve 90 180 () crew pinion cap onto pinion shaft by hand with a Phillips screw driver DO NOT OVE TIGHTEN. opyright 001, 014 Yale ecurity Inc., an OY Group company. ll rights reserved. eproduction in whole in part without the express written permission of Yale ecurity Inc. is prohibited. 809150400 (0514)
100H eries Hold Open rm losers Parallel rm Parts over 1 ight Hand hown /4 (70) /8 (10) (50) OY 7/1 (11) 1/ (1) Opening To 100 101 to 10 11 to 180 91/4 (5) 7/4 (197) 5/4 (14) 188 Plate 75/8 (194) 1/8 (15) 41/8 (105) /Wall/Hardware/Jamb conditions permitting 85/8 (19) 71/8 (181) 51/8 (10) Holes f 188 Plate only Inches (mm) Top of 7 (178) 4 (10) 11/ (8) 1/8 Frame (54) 1/4 (8) 1/ (1) /4 91/1 (19) (0) lose Valves eft Hand ight Hand 4 5 weep Down Up Place rm on pindle atch otate and valves away from hinge emove rm from pindle opyright 001, 014 Yale ecurity Inc., an OY Group company. ll rights reserved. eproduction in whole in part without the express written permission of Yale ecurity Inc. is prohibited. ee tep on Page 4 809150400 (0514)
100H eries Hold Open rm losers Parallel rm OY Open Valves 7 ssemble rm 8 ight Hand eft Hand Flat Y Y Flat aution: Do Not ack Valves out ompletely rm crew 11/ (8) 9 pring Power djust 10 101(F) only (If necessary) P tronger weep 11 atch 1 ackcheck 1 et Hold Open 14 Pinion ap 15 over tronger () aution: Don't completely close valve opyright 001, 014 Yale ecurity Inc., an OY Group company. ll rights reserved. eproduction in whole in part without the express written permission of Yale ecurity Inc. is prohibited. 4 crew pinion cap onto pinion shaft by hand with a Phillips screw driver DO NOT OVE TIGHTEN. 809150400 (0514)
Y 100H eries Hold Open rm losers rm Parts 1 91/1 (0) /4 (19) OY Top of 11/ (8) over E 90 Inches (mm) 1/4 (44) 1/ (1) ight Hand hown /Wall/Hardware/Jamb conditions permitting Opening Dimension "" & valves toward hinge To 100 101 to 10 11 to 180 71/ (191) 1/ (89) onger connecting rod 77011 is required f reveals greater than " (7) eveal FT weep 4 atch 5 eft Hand Nut Up D F G tronger P ackcheck 101(F) Only pring Power djust (If Necessary) et Hold Open 7 Pinion ap over 8 tronger () aution: Don't completely close valve 70 to 180 crew pinion cap onto pinion shaft by hand with a Phillips screw driver DO NOT OVE TIGHTEN. opyright 001, 014 Yale ecurity Inc., an OY Group company. ll rights reserved. eproduction in whole in part without the express written permission of Yale ecurity Inc. is prohibited. 5 809150400 (0514)
100H eries djustments Page weep atch ackcheck (Use 1/8" Hex Wrench f these djustments) OY tronger 70 10 OED pring Power djust 101 (F) only djustment hart DOO TYPE OF INT. 4" (0.85M) Number of Turns equired MXIMUM DOO IE " (0.90M) 40" (1.00M) 44" (1.10M) 48" (1.0M) P To identify your model: ize ode (Use 1/8 Hex Wrench f this djustment) E Date ode =10 =10 4=104 5=105 =10 tronger =101 1 4=101F 101F 101 EXTEIO INTEIO EXTEIO INTEIO egular rm Parallel rm egular rm Parallel rm egular rm Parallel rm egular rm Parallel rm FU 0 TUN OF 1/8 POWE DJUTMENT WENH FU 0 TUN OF 1/8 POWE DJUTMENT WENH To et Hold Open s hipped From Facty 1 1 4 5 5 8 8 9 1 NOT EOMMENDED UE 101 4 9 11 5 7 10 1 5 7 10 1 5 7 10 14 1 18 FU (0 ) TUN MXIMUM VIE Open to Desired ngle Use 1" Wrench opyright 001, 014 Yale ecurity Inc., an OY Group company. ll rights reserved. eproduction in whole in part without the express written permission of Yale ecurity Inc. is prohibited. OY 000 Highway 74 East Monroe, N 811 Tel: (877) 97455 Fax: (800)8095 www.ntondocontrols.com 809150400 (0514)