NTC55 Product Guide. Features. ASME B30.5 Imperial 85% 49,9 t (55 USt) capacity at 2,44 m (8 ft)

Size: px
Start display at page:

Download "NTC55 Product Guide. Features. ASME B30.5 Imperial 85% 49,9 t (55 USt) capacity at 2,44 m (8 ft)"

Transcription

1 NTC Product Guide ASME B30.5 Imperial % Features 49,9 t ( USt) capacity at 2,44 m (8 ft) 39,01 m (128 ft) five-section, full-power boom Hydraulically removable counterweight system with multiple configurations Hydraulically tiltg operator cab Four-position outrigger settgs

2 NATIONAL CRANE NTC The roadability of a boom truck combed with the capacity and performance of a truck crane. Features Extreme versatility and strength With four outrigger configurations, four counterweight configurations, a premium commercial truck chassis for superior roadg performance, and a 49,9 t ( USt) capacity, the NTC is the ideal crane for your fleet. Five-section boom The NTC is equipped with a 39,0 m (128 ft) boom. An optional 7,9 m (26 ft) fixed length offsettable jib and a 7,9 m 13,7 m (26 ft ft) two-section offsettable manual extension is available. Operator-focused design The NTC is designed specifically with the operator md, with up to 20 cab tilt, a graphical RCL with tegrated control system, and lighter polymeric outrigger floats for easy setup. Four-position outriggers Equipped with left and right ground-level and -cab CANbus outrigger controls, the NTC s outriggers allow for quick and easy crane setup. An outrigger beam position system aids the operator selectg the right load chart based on the crane s outrigger footprt. The front outrigger box has an X-shaped footprt that elimates the need for a sgle front outrigger. Load charts are available for %, %, % and fully retracted spans. Options and Lift Solutions Hydraulic hose reels Factory-stalled toolbox options Wireless anti-two-block system

3 Jobsite benefits Truck crane replacement with modern features. 5,5 m 10,4 m (18 ft 34 ft) longer ma boom length than competitive 36,3 t ( USt) truck cranes Four outrigger positions, cludg a unique 6,1 m (20 ft) span for tight operatg spaces (similar to USt truck cranes) Rock-solid operatg performance with less carrier flex and twist than an average boom truck Hydraulically self-removable counterweight with multiple slabs for easy roadg Simpler, smoother and smarter operation. Graphical RCL for easy setup Class-leadg features such as adjustable joystick speeds, on-board diagnostics, and service capabilities without the need for a laptop Offsettable jib options Enhanced comfort, access and egress and setup. Comfort of a commercial truck chassis from leadg manufacturers 20 hydraulically tiltg, ergonomic operator cab Strong alumum deckg with multiple ladders for easy access Lighter polymeric operator floats that are easy to use and less prone to theft when on the job Manitowoc Crane Care when you need it. The assurance of the world s most advanced crane service and support to get you back to work fast. Manitowoc Fance helps you get right to work generatg profits for your busess. Fancial tools that help you capitalize on opportunity with solutions that fit your needs.

4 Contents Dimensions and weights 5 Mountg configurations 7 Workg range 9 Load charts 10 Specifications 37 Symbols glossary 41 4

5 Dimensions 17 (.2) 2943 (115.9) 1276 (.2) C/L ROTATION 649 (25.6) 766 (30.2) FRONT LIFTING LUGS 449 (17.7) S/S HYD RESERVOIR REAR LIFTING LUGS BOLTED STRUCTURAL BUMPER ATTACHED TO TRUCK FRAME 2161 (.1) IPO CWT 1542 (.7) MAIN HOIST 9722 (382.8) RETRACTED 39,014 (1536) EXTENDED (1.9) 79 (1.9) 1941 CHASSIS CAB CLEARANCE 4305 (169.5) STANDARD CAB A/C CLAMPED STUD CONNECTION (FRONT ONLY) WELDED/BOLTED SHEAR PLATE CONNECTION 7258 (2.7) WELDED/BOLTED FLEX PLATE CONNECTION 3300 (129.9) C/L ROTATION 630 (24.8) NTC CWT 296 (11.7) 6,4 (26) OUTRIGGER JACK STROKE WITH STANDARD POLYMERIC OUTRIGGER PADS 6,8 (27) OUTRIGGER JACK STROKE WITH STANDARD ALUMINUM (OPTIONAL) OUTRIGGER PADS Dimensions are mm () unless otherwise specified National Crane NTC 5

6 Dimensions 3303 (130) RET/MID/%/EXT 4813 (189.5) EXTENDED 96 (1.9) % SPAN 43 (172.6) MID-SPAN 37 (1.8) RETRACTED 7388 (2.9) EXT 6121 (241) % 4886 (192.4) MID 2384 (93.9) RET 2387 (94) RET 4738 (186.5) MID 5898 (232.2) % 89 (279.1) EXT Dimensions are mm () unless otherwise specified Configuration Horizontal CG mm () Weight and CG Estimates Weight w/ Fluids kg (lbs) CWT Pned (# slabs) CWT Stowed (# slabs) NTC (24.3) (48,6) 3 0 6

7 Mountg configurations The configurations are based on the NTC with an % stability factor. The complete unit must be stalled accordance with factory requirements and a test performed to determe actual stability and counterweight requirements sce dividual truck chassis vary (488 mm) (62 mm) 0 ( mm) 26.0 (6 mm) 78.0 (1981 mm) ( mm) UPPER AND LOWER CWT SLABS PINNED (18 mm) NTC Series Mimum Truck Specification Workg area: 3 Gross Axle Weight Ratg Front: 72 kg (20,000 lb) Gross Axle Weight Ratg Rear: kg (,000 lb) Gross Axle Weight Ratg Tag: 5987 kg (13,200 lb) Wheelbase: 6 cm (256 ) Cab to Axle/trunnion (CA/CT): 488 cm (192 ) Frame Strength: 7 Mpa (110,000 PSI) Frame Section Modulus (SM), front axle to end of AF: 327 cm 3 (20 3 ) Stability Weight, Front: kg ( lb) mimum Stability Weight, Rear: 49 kg (10,1 lb) mimum NOTE: Estimated axle scale weights prior to stallation of crane assembly for % stability. This configuration does not meet Federal Bridge Law (568 mm) 0 ( mm).0 (1397 mm).0 (1397 mm) UPPER AND LOWER CWT SLABS PINNED (37 mm) NTC Recommended 4 Axle Truck Specification Workg area: 3 Gross Axle Weight Ratg Front: 72 kg (20,000 lb) Gross Axle Weight Ratg Rear: kg (66,000 lb) Wheelbase: 683 cm (269 ) Cab to Axle/trunnion (CA/CT): 488 cm (192 ) Frame Strength: 7 Mpa (110,000 PSI) Frame Section Modulus (SM), front axle to end of AF: 327 cm 3 (20 3 ) Stability Weight, Front: 44 kg (90 lb) mimum Stability Weight, Rear: 4899 kg (10,0 lb) mimum NOTE: Estimated axle scale weights prior to stallation of crane assembly for % stability. This configuration does not meet Federal Bridge Law (6832 mm) (91 mm) 23.4 (594 mm) (66 mm) 0 ( mm) LOWER CWT SLABS STOWED (2642 mm).0 (1397 mm).0 (1397 mm) (2642 mm) (4148 mm) UPPER CWT SLABS PINNED (62 mm) NTC Recommended 6 Axle Truck Specification Workg area: 3 Gross Axle Weight Ratg Front: 72 kg (20,000 lb) Gross Vehicle Weight Ratg Pusher: 3629 kg (00 lb) Gross Axle Weight Ratg Rear: kg (66,000 lb) Gross Axle Weight Ratg Tag: 3629 kg (00 lb) Wheelbase: 671 cm (264 ) Cab to Axle/trunnion (CA/CT): 4 cm (187 ) Frame Strength: 7 Mpa (110,000 PSI) Frame Section Modulus (SM), front axle to end of AF: 327 cm 3 (20 3 ) Stability Weight, Front: 44 kg (90 lb) mimum Stability Weight, Rear: 5896 kg (13,000 lb) mimum NOTE: Estimated axle scale weights prior to stallation of crane assembly for % stability. This configuration does not meet Federal Bridge Law. National Crane NTC 7

8 Mountg configurations Many factors must be considered the selection of proper truck for an NTC crane. Items which must be considered are: 1. Axle Ratg. Axle ratgs are determed by the axles, tires, rims, sprgs, brakes, steerg and frame strength of the truck. If any one of these components is below the required ratg, the gross axle ratg is reduced to its weakest component value. 2. Wheelbase (WB), Cab-to-Trunnion (CT) and Bare Chassis Weight. The wheelbase, CT and chassis weights shown are required so the basic NTC can be legally driven most states and meet stability requirements. The dimensions given assume the sub-base is stalled properly behd the truck cab. If exhaust stacks, transmission protrusions, etc., do not allow a close stallation to the cab, the WB and CT dimensions must be creased. Refer to the Mountg Configuration pages for additional formation. 3. Truck Frame. Try to select a truck frame that will mimize or elimate frame reforcement or extension of the after frame (AF). Many frames are available that have the necessary after frame (AF) section modulus (SM) and resistance to bendg moment (RBM) Mimum truck requirements so that reforcg is not required. The front hydraulic jack is used for a 3 workg range around the truck. The frame under the cab through the front suspension must have the mimum S.M. and RBM because reforcg through the front suspension is often difficult because of enge, radiator mounts and steerg mechanics. See Truck Requirements and Frame Strength pages for the necessary section modulus and resistance to bendg moment values. Integral extended front frame rails are required for front center stabilizer stallation. 4. Additional Equipment. In addition to the axle ratgs, wheelbase, cab-to-axle requirements and frame, it is recommended that the truck is equipped with electronic enge control, creased coolg and a transmission with a PTO openg available with an extra heavy duty PTO. A conventional cab truck should be used for standard crane mounts. 5. Neutral Start Switch. The chassis must be equipped with a switch that prevents operation of the enge starter when the transmission is gear. Notes: Gross Vehicle Weight Ratg (GVWR) is dependent on all components of the vehicle (axles, tires, sprgs, frame, etc.) meetg manufacturers recommendations; always specify GVWR when purchasg trucks Diesel enges require a variable speed governor for smooth crane operation; electronic fuel jection requires EET enge remote throttle All mountg data is based on a National Crane NTC with an % stability factor The complete unit must be stalled accordance with factory requirements, and a test performed to determe actual stability and counterweight requirements per SAE J7; contact the factory for details 8

9 Workg range 39,01 m (128 ft) 7,9 m 13,7 m (26ft ft) 1 Boom deflection not shown 1 Offset ' Ext. 1 3 Offset 1 26' Ext Height from ground Boom length and extension Max boom angle Operatg radius from axis of rotation 10 Axis of rotation (6' 9") (8' 7") Dimensions are for largest furnished hookblock and headache ball with anti-two-block activated. *This drawg shows the physical reach of the mache. Always refer to load chart to see which portions of this diagram are valid for the specific mache configuration and where the loads are structurally or stability limited. National Crane NTC 9

10 9,7 m 39,0 m 2494 kg (31.7 ft 128 ft) (50 lb) % # A 54-B 64-C -D 86-E 97-F 107-G 118-H ,000 (68.1) 92,300 (64) (71.6) 81,200,200 47,6 31,6 (21.8) (68.7) (56.7) 37,0 30,0 (37.3) 22,300 (23.6) (73.4) (.1) 38,000 30,4 (51.3) 24,9 (43.9) 20,4 (.2) *16,0,300,300,300 (68.8) 37,1 30,0 (58.6) 25,1 20,0 (47) 16,0 13,0 11,4 (22.2) 34, (78.7) 34, 34, (72.5) 30, 27, (64.2) 24,0 20,8 (.1) 16,8 () 13,0 (44.6) 11,0 (38.6) (23.9) *46 (9.2) 22,6 (78.3) 22,6 () 22,6 (71.5) 20,0 18,0 (64.3) 17,0 15,0 (56.5) 14,000 (52.3) 11,0 (47.8) (37.9) 72 (31.8) 62 (24.3) *40 (12.8) 17,0 (77.1) 17,0 (74.2) 17,0 (71.2) 16,300 15, 14,000 (61.5) 12,8 11,0 (54.4) 10,0 (.8) (46.6) 73 (42.1) 54 (31.6) 4710 (24.8) *38 (15.3) (78.6) (76.1) 13,6 12,5 () 11,0 (62) 10,9 (59.2) 10, (56) 86 (52.4) 7420 (48.7) (44.7) 20 (.5) 47 (.8) 4110 (30.4) 30 *20 (14.9) (77.8) (73.2) 12,0 11,300 (68.2) 10,6 (.8) 10,000 (63.2) (.4) 86 (57.5) 74 (54.3) 64 (51) 4810 (43.8) 41 (39.8) (.4) 30 (30.5) 20 (24.6) (78.9) (74.8) (72.7) (.6) (.9) 78 (63.3) 00 (.6) 6300 (57.9) 50 () 51 (52.1) 46 (49) 41 (.7) 30 (42.2) 30 (38.4) 2630 (34.2) (16.8) (29.5) (23.7) *1 (15.8) Mimum boom angle ( ) for dicated length (no load) Maximum boom length (ft) at (no load) 97 NOTE: ( ) Boom angles are degrees. *Loads are structurally limited. #RCL operatg code. Refer to RCL manual for operatg structions. Liftg Capacities at Zero Degree Boom Angle Boom Angle A 54-B 64-C -D 86-E (27.6) (38.8) 48 (49.8) (81.8) NOTE: ( ) Reference radii

11 9,7 m 39,0 m (31.7 ft 128 ft) Stowed 2494 kg % (50 lb) # A 54-B 64-C -D 86-E 97-F 107-G 118-H ,0 (68.1) 91,1 (64) (71.6),0 64,0 46,0 30,0 (21.8) (68.7) (56.7) 36,0 29,2 (37.3) 21,0 (23.6) (73.4) (.1) 37,0 29,8 (51.3) 24,0 (43.9) 19,8 (.2) *15,0 39,0 39,0 39,0 (68.8) 36,6 30,200 (58.6) 24,6 20,200 (47) 16,200 13,200 10,9 (22.2) 33,6 (78.7) 33,6 33,6 (72.5) 29,6 26,6 (64.2) 24,1 20,0 (.1) 16,0 () 13,4 (44.6) 11,1 (38.6) (23.9) *4200 (9.2) (78.3) () (71.5) 20,000 18, (64.3) 16,6 15,0 (56.5) 13,0 (52.3) 11,300 (47.8) 8110 (37.9) 68 (31.8) 58 (24.3) *00 (12.8) (77.1) (74.2) (71.2) 15,9 14,0 13,6 (61.5) 12,0 11,0 (54.4) 90 (.8) 82 (46.6) 20 (42.1) (31.6) 43 (24.8) *00 (15.3) (78.6) (76.1) 13,0 12,2 () 11,4 (62) 10,6 (59.2) 90 (56) 83 (52.4) 7120 (48.7) 6 (44.7) 5220 (.5) 44 (.8) 3810 (30.4) 3230 * (14.9) 12,0 (77.8) 12,0 12,0 (73.2) 11,0 11,000 (68.2) 10,0 (.8) 90 (63.2) 9 (.4) 83 (57.5) 71 (54.3) 61 (51) (43.8) 38 (39.8) 32 (.4) 27 (30.5) 2300 (24.6) (78.9) (74.8) (72.7) (.6) (.9) (63.3) (.6) (57.9) 54 () 40 (52.1) 40 (49) 30 (.7) 30 (42.2) 28 (38.4) 23 (34.2) (16.8) (29.5) (23.7) *8 (15.8) Mimum boom angle ( ) for dicated length (no load) Maximum boom length (ft) at (no load) 97 NOTE: ( ) Boom angles are degrees. *Loads are structurally limited. #RCL operatg code. Refer to RCL manual for operatg structions. Liftg Capacities at Zero Degree Boom Angle Boom Angle A 54-B 64-C -D 86-E 11,0 (27.6) 60 (38.8) 42 (49.8) (81.8) NOTE: ( ) Reference radii National Crane NTC 11

12 9,7 m 39,0 m (31.7 ft 128 ft) 2494 kg (50 lb) % Over Rear # A 54-B 64-C -D 86-E 97-F 107-G 118-H ,000 (68.1) 92,300 (64) 81,200,200 47,6 31,6 (21.8) (27.6) (71.6) (68.7) (56.7) 37,0 30,0 (37.3) 22,300 (23.6) (38.8) (73.4) (.1) 38,000 30,4 (51.3) 24,9 (43.9) 20,0 (.2) 16,0 48 (49.8),300,300,300 (68.8) 37,1 30,0 (58.6) 25,1 21,0 (47) 17,8 15,2 *11,0 (22.2) 34, (78.7) 34, 34, (72.5) 30, 27, (64.2) 24,0 21,2 (.1) 18,0 () 15,0 (44.6) 13,0 (38.6) 11, (23.9) *46 (9.2) ,6 (78.3) 22,6 () 22,6 (71.5) 20,0 18,0 (64.3) 17,0 15,0 (56.5) 14,0 (52.3) 13,1 (47.8) 11,2 97 (37.9) 84 (31.8) 73 (24.3) *40 (12.8) 11 (81.8) 17,0 (77.1) 17,0 (74.2) 17,0 (71.2) 16,300 15, 14,000 (61.5) 12,8 12,000 (54.4) 11,2 (.8) 98 (46.6) (42.1) 74 (31.6) 5720 (24.8) *38 (15.3) (78.6) (76.1) 13,6 12,5 () 11,0 (62) 10,9 (59.2) 10,300 (56) 90 (52.4) 8620 (48.7) 20 (44.7) (.5) 57 (.8) (30.4) 44 *20 (14.9) (77.8) (73.2) 12,0 11,300 (68.2) 10,6 (.8) 10,000 (63.2) (.4) 88 (57.5) (54.3) (51) (43.8) 5110 (39.8) 44 (.4) 3930 (30.5) 3430 (24.6) (78.9) (74.8) (72.7) (.6) 8,0 (.9) 78 (63.3) 00 (.6) 6300 (57.9) 50 () 51 (52.1) 46 (49) 41 (.7) (42.2) 3300 (38.4) 3000 (34.2) 110 *20 26 (16.8) (29.5) (23.7) 1 (15.8) Mimum boom angle ( ) for dicated length (no load) Maximum boom length (ft) at (no load) 97 NOTE: ( ) Boom angles are degrees. *Loads are structurally limited. #RCL operatg code. Refer to RCL manual for operatg structions. Liftg Capacities at Zero Degree Boom Angle Boom Angle A 54-B 64-C -D 86-E NOTE: ( ) Reference radii

13 9,7 m 39,0 m (31.7 ft 128 ft) 2494 kg Stowed (50 lb) % Over Rear # A 54-B 64-C -D 86-E 97-F 107-G 118-H ,0 (68.1) 91,1 (64),0 64,0 46,0 30,0 (21.8) 11,0 (27.6) (71.6) (68.7) (56.7) 36,0 29,2 (37.3) 21,0 (23.6) 60 (38.8) (73.4) (.1) 37,0 29,8 (51.3) 24,0 (43.9) 20,200 (.2) 15,0 42 (49.8) 39,0 39,0 39,0 (68.8) 36,6 30,200 (58.6) 24,6 20,5 (47) 17,0 14,0 *11,0 (22.2) ,6 (78.7) 33,6 33,6 (72.5) 29,6 26,6 (64.2) 24,1 20,0 (.1) 17,0 () 14,9 (44.6) 12,0 (38.6) 10, (23.9) *4200 (9.2) 10 (78.3) () (71.5) 20,000 18, (64.3) 16,6 15,0 (56.5) 14,200 (52.3) 12,0 (47.8) 10,8 93 (37.9) (31.8) 69 (24.3) *00 (12.8) 0 (81.8) (77.1) (74.2) (71.2) 15,9 14,0 13,6 (61.5) 12,0 11,6 (54.4) 10,0 (.8) 10 (46.6) 8220 (42.1) (31.6) 53 (24.8) *00 (15.3) (78.6) (76.1) 13,0 12,2 () 11,4 (62) 10,6 (59.2) 10,000 (56) (52.4) 8320 (48.7) 7220 (44.7) 62 (.5) 54 (.8) 47 (30.4) 41 * (14.9) 12,0 (77.8) 12,0 12,0 (73.2) 11,0 11,000 (68.2) 10,0 (.8) 90 (63.2) 9 (.4) (57.5) 8 (54.3) 72 (51) (43.8) 4810 (39.8) 41 (.4) 3630 (30.5) 3130 (24.6) (78.9) (74.8) (72.7) (.6) (.9) (63.3) (.6) (57.9) 54 () 40 (52.1) 40 (49) 30 (.7) 34 (42.2) 30 (38.4) 20 (34.2) 110 *2 20 (16.8) (29.5) (23.7) 8 (15.8) Mimum boom angle ( ) for dicated length (no load) Maximum boom length (ft) at (no load) 97 NOTE: ( ) Boom angles are degrees. *Loads are structurally limited. #RCL operatg code. Refer to RCL manual for operatg structions. Liftg Capacities at Zero Degree Boom Angle Boom Angle A 54-B 64-C -D 86-E NOTE: ( ) Reference radii. 03 National Crane NTC 13

14 7,9 m 13,7 m (26 ft ft) 2494 kg (50 lb) % M. boom angle for dicated length (no load) Max. boom length at boom angle (no load) **26 ft Length #0005 #0007 #0009 #0011 (.3) (73.6) (71.9) (.1) (66.7) (62.6) (58.3) 37 (56.1) 3200 (53.8) 26 (51.2) 2230 (48.4) 1810 (.5) 14 (42.5) 1 (39.3) 0 (.8) 520 (32.1) 3 (77.4) (73.7) (71.7) 46 (69.7) 40 (67.5) 41 (.2) 00 (62.9) (58.1) 3130 (.4) 2620 (52.5) 21 (49.5) 17 (46.3) 13 (42.7) 1010 (38.9) 6 (34.8) ft Length (77.3) (.8) (74.4) (72.9) (71.4) (69.9) (66.9) (.4) (63.8) (61.9) 32 (59.9) 3000 (57.8) 20 (.6) 24 (53.5) 20 (51.2) 10 (48.7) 14 (46) 11 8 (.4) 6 3 (77) (.2) (71.7) (69.8) (67.9) (.9) 24 (61.7) 20 (59.5) 20 (57.1) 2300 (54.7) 19 (52.1) 15 (49.1) 12 (.9) 9 (42.3) 0 (38.2) ft 64 ft NOTE: ( ) Boom angles are degrees. 04 #RCL operatg code. Refer to RCL manual for structions. *Loads are structurally limited. **26 ft. capacities are applicable to both 26' fixed and 26' tele extension. Boom extension capacity notes: ft and ft extension lengths may be used for sgle le liftg service. 2. Radii listed are for a fully extended boom with the boom extension erected. For ma boom lengths less than fully extended, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is configured. For boom angles not shown, use the ratg of the next lower boom angle. Warng: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 3. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 4. Capacities listed are with outriggers properly extended and vertical jacks set only. 14

15 7,9 m 13,7 m (26 ft ft) 2494 kg (50 lb) % Over Rear - S/N M. boom angle for dicated length (no load) Max. boom length at boom angle (no load) **26 ft Length ft Length #0006 #0008 #0010 #0012 (.3) (73.6) (71.9) (.1) (66.7) (62.6) (58.3) 30 (56.1) 36 (53.8) 31 (51.2) 20 (48.4) 2 (.5) 10 (42.5) 10 (39.3) 9 (.8) 6 (32.1) 3 (77.4) (73.7) (71.7) 46 (69.7) 40 (67.5) 41 (.2) 00 (62.9) (58.1) 30 (.4) 20 (52.5) 25 (49.5) 21 (46.3) 16 (42.7) 1200 (38.9) 8 (34.8) 4 (30) (77.3) (.8) (74.4) (72.9) (71.4) (69.9) (66.9) (.4) (63.8) (61.9) 32 (59.9) 3000 (57.8) 20 (.6) (53.5) 2300 (51.2) 20 (48.7) 10 (46) (.4) 0 64 ft 64 ft 3 (77) (.2) (71.7) (69.8) (67.9) (.9) 24 (61.7) 20 (59.5) 20 (57.1) 2300 (54.7) 22 (52.1) 2000 (49.1) 10 (.9) 10 (42.3) 6 0 (33.9) (38.2) 0 (33.9) NOTE: ( ) Boom angles are degrees. 09 #RCL operatg code. Refer to RCL manual for structions. *Loads are structurally limited. **26 ft. capacities are applicable to both 26' fixed and 26' tele extension. Boom extension capacity notes: ft and ft extension lengths may be used for sgle le liftg service. 2. Radii listed are for a fully extended boom with the boom extension erected. For ma boom lengths less than fully extended, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is configured. For boom angles not shown, use the ratg of the next lower boom angle. Warng: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 3. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 4. Capacities listed are with outriggers properly extended and vertical jacks set only. National Crane NTC 15

16 9,7 m 39,0 m 2494 kg (31.7 ft 128 ft) (50 lb) % # (14.9) Mimum boom angle ( ) for dicated length (no load) 6 13 Maximum boom length (ft) at (no load) NOTE: ( ) Boom angles are degrees. #RCL operatg code. Refer to RCL manual for operatg structions. Liftg Capacities at Zero Degree Boom Angle Boom Angle A 54-B 64-C -D 86-E A 54-B 64-C -D 86-E 97-F 107-G 118-H ,0 (68.1),200 (64),1,200 47,6 31,6 (21.8) (27.6) (71.6) (68.7) (56.7) 33,1 23,300 (37.3) 17,0 (23.6) (38.8) NOTE: ( ) Reference radii. (73.4) (.1) 33,0 23,0 (51.3) 17,0 (43.9) 13,0 (.2) 10,9 48 (49.8),300,300,300 (68.8) 33,0 23,9 (58.6) 18,0 14,0 (47) 11, (22.2) 34, (78.7) 34, 34, (72.5) 30, 24, (64.2) 18,200 14,200 (.1) 11,0 () 92 (44.6) (38.6) (23.9) 41 (9.2) ,6 (78.3) 22,6 () 22,6 (71.5) 20,0 18,300 (64.3) 14,300 11,4 (56.5) 93 (52.3) 76 (47.8) 52 (37.9) 4320 (31.8) 30 (24.3) 28 (12.8) 11 (81.8) 17,0 (77.1) 17,0 (74.2) 17,0 (71.2) 16,300 14,0 11,0 (61.5) (54.4) 6420 (.8) 5320 (46.6) 40 (42.1) (31.6) 23 (24.8) 18 (15.3) (78.6) (76.1) 13,6 11,5 () (62) 7820 (59.2) 64 (56) 53 (52.4) 44 (48.7) 36 (44.7) 3000 (.5) 2420 (.8) 1920 (30.4) 86 (78.9) (74.8) (72.7) (.6) 78 (.9) (63.3) 54 (.6) 20 (57.9) 37 () 30 (52.1) 24 (49) 19 (.7) 15 (42.2) 11 (38.4) 7 (34.2) (77.8) (73.2) 12,0 11,300 (68.2) (.8) 78 (63.2) 10 (.4) 5410 (57.5) 44 (54.3) 3710 (51) (43.8) 19 (39.8) 1510 (.4) 1110 (30.5) 7 (24.6) A 16

17 9,7 m 39,0 m (31.7 ft 128 ft) 2494 kg Stowed % (50 lb) # A 54-B 64-C -D 86-E 97-F 107-G 118-H 128 Mimum boom angle ( ) for dicated length (no load) Maximum boom length (ft) at (no load) 86 NOTE: ( ) Boom angles are degrees. #RCL operatg code. Refer to RCL manual for operatg structions. Liftg Capacities at Zero Degree Boom Angle Boom Angle A 54-B 64-C -D 86-E 101,000 (68.1) 89,0 (64) 79,000 64,0 46,0 30,0 (21.8) 11,0 (27.6) (71.6) (68.7) (56.7) 32,0 22,0 (37.3) 16,5 (23.6) 60 (38.8) NOTE: ( ) Reference radii. (73.4) (.1) 33,000 23, (51.3) 17,200 (43.9) 13,200 (.2) 10,0 42 (49.8) 39,0 39,0 39,0 (68.8) 33,2 23,4 (58.6) 17,5 13,5 (47) 10,0 68 (22.2) ,6 (78.7) 33,6 33,6 (72.5) 29,6 23,6 (64.2) 17,0 13,0 (.1) 10,0 () 8810 (44.6) 7130 (38.6) (23.9) 3720 (9.2) 10 (78.3) () (71.5) 20,000 17,0 (64.3) 13,0 11,0 (56.5) 89 (52.3) 72 (47.8) (37.9) 3920 (31.8) 3130 (24.3) 24 (12.8) 0 (81.8) (77.1) (74.2) (71.2) 15,9 14,000 11,1 (61.5) (54.4) (.8) 49 (46.6) (42.1) (31.6) 2020 (24.8) 10 (15.3) (78.6) (76.1) 13,0 11,2 () 9200 (62) 20 (59.2) 61 (56) (52.4) 41 (48.7) 33 (44.7) 20 (.5) 2120 (.8) 1620 (30.4) 11 7 (14.9) 12,0 (77.8) (78.9) 12,0 12,0 (73.2) (74.8) 11,0 (72.7) 11,000 (68.2) (.6) (.8) 76 (63.2) (.9) (.4) (63.3) (57.5) (.6) (54.3) (57.9) (51) () (52.1) (43.8) (49) (39.8) (.7) (.4) (42.2) (30.5) (38.4) 5 (34.2) A National Crane NTC 17

18 7,9 m 13,7 m (26 ft ft) 2494 kg (50 lb) % 36 **26 ft Length ft Length #0205 #0207 #0209 # (.3) (77.3) (73.6) (.8) (71.9) (.1) (77.4) (73.7) (74.4) (72.9) (71.4) (66.7) (62.6) (58.3) (56.1) (53.8) (51.2) (71.7) (69.7) (67.5) (.2) (62.9) (58.1) (.4) (69.9) (66.9) (.4) (63.8) (61.9) (59.9) (57.8) (77) (.2) (71.7) (69.8) (67.9) (.9) (52.5) (.6) (61.7) (53.5) (59.5) (57.1) (54.7) M. boom angle for dicated length (no load) Max. boom length at boom angle (no load) 64 ft 64 ft NOTE: ( ) Boom angles are degrees A #RCL operatg code. Refer to RCL manual for structions. *Loads are structurally limited. **26 ft. capacities are applicable to both 26' fixed and 26' tele extension. Boom extension capacity notes: ft and ft extension lengths may be used for sgle le liftg service. 2. Radii listed are for a fully extended boom with the boom extension erected. For ma boom lengths less than fully extended, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is configured. For boom angles not shown, use the ratg of the next lower boom angle. Warng: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 3. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 4. Capacities listed are with outriggers properly extended and vertical jacks set only. 18

19 9,7 m 39,0 m (31.7 ft 128 ft) 1928 kg (42 lb) % # A 54-B 64-C -D 86-E 97-F 107-G 118-H ,0 (68.1) 92,300 (64) 81,1 64,0 47,0 31,6 (21.8) (27.6) (71.6) (68.7) (56.7) 37, 29,0 (37.3) 22,300 (23.6) (38.8) NOTE: ( ) Reference radii. (73.4) (.1) 37,0 29,0 (51.3) 24,4 (43.9) 19,5 (.2) 15,0 48 (49.8),300,300,300 (68.8) 37,1 30,1 (58.6) 24,0 19,0 (47) 15,9 13,0 10,0 (22.2) 34, (78.7) 34, 34, (72.5) 30, 27, (64.2) 24,0 20,000 (.1) 16, () 13,2 (44.6) 11, (38.6) 7920 (23.9) *46 (9.2) ,6 (78.3) 22,6 () 22,6 (71.5) 20,0 18,0 (64.3) 17,0 15,0 (56.5) 13,0 (52.3) 11,200 (47.8) 94 (37.9) 68 (31.8) 58 (24.3) *40 (12.8) 11 (81.8) 17,0 (77.1) 17,0 (74.2) 17,0 (71.2) 16,300 15, 14,000 (61.5) 12,8 11,200 (54.4) (.8) 8130 (46.6) 69 (42.1) (31.6) 43 (24.8) 3730 (15.3) (78.6) (76.1) 13,6 12,5 () 11,0 (62) 10,9 (59.2) (56) 81 (52.4) 00 (48.7) 00 (44.7) 51 (.5) 4430 (.8) 37 (30.4) (14.9) (77.8) (73.2) 12,0 11,300 (68.2) 10,6 (.8) 10,000 (63.2) (.4) 8210 (57.5) 30 (54.3) (51) 44 (43.8) 3830 (39.8) 32 (.4) 27 (30.5) 2330 (24.6) (78.9) (74.8) (72.7) (.6) (.9) 78 (63.3) 00 (.6) 6300 (57.9) 50 () 51 (52.1) 40 (49) 38 (.7) 3300 (42.2) 2810 (38.4) 23 (34.2) (16.8) (29.5) (23.7) *1 (15.8) Mimum boom angle ( ) for dicated length (no load) Maximum boom length (ft) at (no load) 97 NOTE: ( ) Boom angles are degrees. *Loads are structurally limited. #RCL operatg code. Refer to RCL manual for operatg structions. Liftg Capacities at Zero Degree Boom Angle Boom Angle A 54-B 64-C -D 86-E A National Crane NTC 19

20 9,7 m 39,0 m (31.7 ft 128 ft) 1928 kg Stowed % (42 lb) # A 54-B 64-C -D 86-E 97-F 107-G 118-H ,000 (68.1) 91,1 (64),000 63,200,0 30,0 (21.8) 11,0 (27.6) (71.6) (68.7) (56.7) 36,300 28,0 (37.3) 21,0 (23.6) 60 (38.8) NOTE: ( ) Reference radii. (73.4) (.1) 36,0 29,300 (51.3) 23,8 (43.9) 18,9 (.2) 15, 42 (49.8) 39,0 39,0 39,0 (68.8) 36,6 29,6 (58.6) 24,200 19,300 (47) 15,4 12,5 10,0 (22.2) ,6 (78.7) 33,6 33,6 (72.5) 29,6 26,6 (64.2) 24,1 19,5 (.1) 15,6 () 12,0 (44.6) 10,6 (38.6) 74 (23.9) *4200 (9.2) 10 (78.3) () (71.5) 20,000 18, (64.3) 16,6 15,0 (56.5) 12,9 (52.3) 10,0 (47.8) 76 (37.9) 64 (31.8) 54 (24.3) *00 (12.8) 0 (81.8) (77.1) (74.2) (71.2) 15,9 14,0 13,6 (61.5) 12,0 10,8 (54.4) 9200 (.8) 77 (46.6) 60 (42.1) 47 (31.6) 20 (24.8) 33 (15.3) (78.6) (76.1) 13,0 12,2 () 11,4 (62) 10,6 (59.2) 9300 (56) 78 (52.4) 60 (48.7) 50 (44.7) 48 (.5) 4130 (.8) 34 (30.4) (14.9) 12,0 (77.8) 12,0 12,0 (73.2) 11,0 11,000 (68.2) 10,0 (.8) 90 (63.2) 9 (.4) 7910 (57.5) 6730 (54.3) 57 (51) (43.8) 30 (39.8) 29 (.4) 24 (30.5) 2030 (24.6) (78.9) (74.8) (72.7) (.6) (.9) (63.3) (.6) (57.9) 54 () 40 (52.1) 42 (49) 3610 (.7) 30 (42.2) 25 (38.4) 2110 (34.2) (16.8) (29.5) (23.7) *8 (15.8) Mimum boom angle ( ) for dicated length (no load) Maximum boom length (ft) at (no load) 97 NOTE: ( ) Boom angles are degrees. *Loads are structurally limited. #RCL operatg code. Refer to RCL manual for operatg structions. Liftg Capacities at Zero Degree Boom Angle Boom Angle A 54-B 64-C -D 86-E A 20

21 9,7 m 39,0 m (31.7 ft 128 ft) 1928 kg (42 lb) % Over Rear National Crane NTC # A 54-B 64-C -D 86-E 97-F 107-G 118-H ,0 (68.1) 92,300 (64) 81,1 64,0 47,0 31,6 (21.8) (27.6) (71.6) (68.7) (56.7) 37, 29,0 (37.3) 22,300 (23.6) (38.8) NOTE: ( ) Reference radii. (73.4) (.1) 37,0 29,0 (51.3) 24,4 (43.9) 20,0 (.2) 16,0 48 (49.8),300,300,300 (68.8) 37,1 30,1 (58.6) 24,0 20,6 (47) 17,0 *11,0 (22.2) 34, (78.7) 34, 34, (72.5) 30, 27, (64.2) 24,0 20,8 (.1) 17,0 () 14,8 (44.6) 12,5 (38.6) 10,0 92 (23.9) *46 (9.2) ,6 (78.3) 22,6 () 22,6 (71.5) 20,0 18,0 (64.3) 17,0 15,0 (56.5) 14,0 (52.3) 12,0 (47.8) 10,8 93 (37.9) 8 (31.8) 30 (24.3) *40 (12.8) 11 (81.8) 17,0 (77.1) 17,0 (74.2) 17,0 (71.2) 16,300 15, 14,000 (61.5) 12,8 12,000 (54.4) 10,9 (.8) 94 (46.6) 81 (42.1) (31.6) 5410 (24.8) *38 (15.3) (78.6) (76.1) 13,6 12,5 () 11,0 (62) 10,9 (59.2) 10,300 (56) 94 (52.4) 8230 (48.7) 71 (44.7) 62 (.5) 54 (.8) 47 (30.4) 41 *20 (14.9) (77.8) (73.2) 12,0 11,300 (68.2) 10,6 (.8) 10,000 (63.2) (.4) 88 (57.5) 82 (54.3) 7200 (51) (43.8) 4820 (39.8) 4210 (.4) 36 (30.5) 31 (24.6) (78.9) (74.8) (72.7) (.6) (.9) 78 (63.3) 00 (.6) 6300 (57.9) 50 () 51 (52.1) 46 (49) 41 (.7) (42.2) 3300 (38.4) 3000 (34.2) 110 *20 26 (16.8) (29.5) (23.7) 1 (15.8) Mimum boom angle ( ) for dicated length (no load) Maximum boom length (ft) at (no load) 97 NOTE: ( ) Boom angles are degrees. *Loads are structurally limited. #RCL operatg code. Refer to RCL manual for operatg structions. Liftg Capacities at Zero Degree Boom Angle Boom Angle A 54-B 64-C -D 86-E A 21

22 9,7 m 39,0 m (31.7 ft 128 ft) 1928 kg Stowed (42 lb) % Over Rear # A 54-B 64-C -D 86-E 97-F 107-G 118-H ,000 (68.1) 91,1 (64),000 63,200,0 30,0 (21.8) 11,0 (27.6) (71.6) (68.7) (56.7) 36,300 28,0 (37.3) 21,0 (23.6) 60 (38.8) NOTE: ( ) Reference radii. (73.4) (.1) 36,0 29,300 (51.3) 23,8 (43.9) 19,0 (.2) 15,0 42 (49.8) 39,0 39,0 39,0 (68.8) 36,6 29,6 (58.6) 24,200 20,1 (47) 17,000 14,200 *11,0 (22.2) ,6 (78.7) 33,6 33,6 (72.5) 29,6 26,6 (64.2) 24,1 20,0 (.1) 17,2 () (44.6) 12, (38.6) 10, (23.9) *4200 (9.2) 10 (78.3) () (71.5) 20,000 18, (64.3) 16,6 15,0 (56.5) 14,200 (52.3) 12,200 (47.8) 10,4 89 (37.9) 70 (31.8) 6630 (24.3) *00 (12.8) 0 (81.8) (77.1) (74.2) (71.2) 15,9 14,0 13,6 (61.5) 12,0 11,6 (54.4) 10,0 (.8) (46.6) 7830 (42.1) (31.6) (24.8) *00 (15.3) (78.6) (76.1) 13,0 12,2 () 11,4 (62) 10,6 (59.2) 10,000 (56) 91 (52.4) 7930 (48.7) 68 (44.7) 59 (.5) 51 (.8) 44 (30.4) 38 * (14.9) 12,0 (77.8) 12,0 12,0 (73.2) 11,0 11,000 (68.2) 10,0 (.8) 90 (63.2) 9 (.4) (57.5) 79 (54.3) 60 (51) (43.8) 20 (39.8) 3910 (.4) 33 (30.5) 28 (24.6) (78.9) (74.8) (72.7) (.6) (.9) (63.3) (.6) (57.9) 54 () 40 (52.1) 40 (49) 30 (.7) 34 (42.2) 30 (38.4) 20 (34.2) 110 *2 20 (16.8) (29.5) (23.7) 8 (15.8) Mimum boom angle ( ) for dicated length (no load) Maximum boom length (ft) at (no load) 97 NOTE: ( ) Boom angles are degrees. *Loads are structurally limited. #RCL operatg code. Refer to RCL manual for operatg structions. Liftg Capacities at Zero Degree Boom Angle Boom Angle A 54-B 64-C -D 86-E A 22

23 7,9 m 13,7 m (26 ft ft) 1928 kg (42 lb) % **26 ft Length ft Length #05 #07 #09 #11 (.3) (73.6) (71.9) (.1) (66.7) (62.6) (58.3) 34 (56.1) 20 (53.8) 20 (51.2) 19 (48.4) 15 (.5) 1200 (42.5) 8 (39.3) 5 (.8) 3 (77.4) (73.7) (71.7) 46 (69.7) 40 (67.5) 41 (.2) 00 (62.9) (58.1) 28 (.4) 20 (52.5) 1910 (49.5) 10 (46.3) 1130 (42.7) 7 (38.9) 4 (34.8) (77.3) (.8) (74.4) (72.9) (71.4) (69.9) (66.9) (.4) (63.8) (61.9) 32 (59.9) 3000 (57.8) 2620 (.6) 2220 (53.5) 18 (51.2) 1520 (48.7) 1220 (46) 9 6 (.4) 3 (77) (.2) (71.7) (69.8) (67.9) (.9) 24 (61.7) 20 (59.5) 20 (57.1) 20 (54.7) 1720 (52.1) 13 (49.1) 10 (.9) (42.3) 1 M. boom angle for dicated length (no load) Max. boom length (38.2) 36 at boom angle (no load) 64 ft 64 ft NOTE: ( ) Boom angles are degrees A #RCL operatg code. Refer to RCL manual for structions. *Loads are structurally limited. **26 ft. capacities are applicable to both 26' fixed and 26' tele extension. Boom extension capacity notes: ft and ft extension lengths may be used for sgle le liftg service. 2. Radii listed are for a fully extended boom with the boom extension erected. For ma boom lengths less than fully extended, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is configured. For boom angles not shown, use the ratg of the next lower boom angle. Warng: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 3. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 4. Capacities listed are with outriggers properly extended and vertical jacks set only. National Crane NTC 23

24 7,9 m 13,7 m (26 ft ft) 1928 kg (42 lb) % Over Rear S/N M. boom angle for dicated length (no load) Max. boom length at boom angle (no load) **26 ft Length ft Length #06 #08 #10 #12 (.3) (73.6) (71.9) (.1) (66.7) (62.6) (58.3) 30 (56.1) 36 (53.8) 31 (51.2) 20 (48.4) 2 (.5) 10 (42.5) 10 (39.3) 9 (.8) 6 (32.1) 3 (77.4) (73.7) (71.7) 46 (69.7) 40 (67.5) 41 (.2) 00 (62.9) (58.1) 30 (.4) 20 (52.5) 25 (49.5) 21 (46.3) 16 (42.7) 1200 (38.9) 8 (34.8) 4 (30) (77.3) (.8) (74.4) (72.9) (71.4) (69.9) (66.9) (.4) (63.8) (61.9) 32 (59.9) 3000 (57.8) 20 (.6) (53.5) 2300 (51.2) 20 (48.7) 10 (46) (.4) 0 64 ft 64 ft 3 (77) (.2) (71.7) (69.8) (67.9) (.9) 24 (61.7) 20 (59.5) 20 (57.1) 2300 (54.7) 22 (52.1) 2000 (49.1) 1720 (.9) *10 (42.3) 6 *0 (33.9) (38.2) 0 (33.9) NOTE: ( ) Boom angles are degrees A #RCL operatg code. Refer to RCL manual for structions. *Loads are structurally limited. **26 ft. capacities are applicable to both 26' fixed and 26' tele extension. Boom extension capacity notes: ft and ft extension lengths may be used for sgle le liftg service. 2. Radii listed are for a fully extended boom with the boom extension erected. For ma boom lengths less than fully extended, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is configured. For boom angles not shown, use the ratg of the next lower boom angle. Warng: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 3. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 4. Capacities listed are with outriggers properly extended and vertical jacks set only. 24

25 9,7 m 39,0 m (31.7 ft 128 ft) 1928 kg (42 lb) % # A 54-B 64-C -D 86-E 97-F 107-G 118-H (14.9) Mimum boom angle ( ) for dicated length (no load) Maximum boom length (ft) at (no load) NOTE: ( ) Boom angles are degrees. #RCL operatg code. Refer to RCL manual for operatg structions. Liftg Capacities at Zero Degree Boom Angle Boom Angle A 54-B 64-C -D 86-E 102,0 (68.1) 89,9 (64) 79,0 64,0 47,0 30,0 (21.8) (27.6) (71.6) (68.7) (56.7) 31,0 (37.3) 16,0 (23.6) (38.8) NOTE: ( ) Reference radii. (73.4) (.1) 32,200 22,6 (51.3) 16,9 (43.9) 13, (.2) 10,0 48 (49.8),300,300,300 (68.8) 32,4 22,0 (58.6) 17,200 13,0 (47) 10, (22.2) 34, (78.7) 34, 34, (72.5) 30, 23,0 (64.2) 17,0 13,0 (.1) 10,0 () 8730 (44.6) 7110 (38.6) (23.9) 3820 (9.2) ,6 (78.3) 22,6 () 22,6 (71.5) 20,0 (64.3) 13,0 10,0 (56.5) 88 (52.3) 7220 (47.8) (37.9) 39 (31.8) 3210 (24.3) 25 (12.8) 11 (81.8) 17,0 (77.1) 17,0 (74.2) 17,0 (71.2) 16,300 13,6 11,000 (61.5) (54.4) 00 (.8) 49 (46.6) (42.1) (31.6) 20 (24.8) 15 (15.3) (78.6) (76.1) 13,6 11,0 () 89 (62) (59.2) (56) 49 (52.4) 4 (48.7) 33 (44.7) 20 (.5) 21 (.8) 16 (30.4) 86 (77.8) (78.9) (73.2) (74.8) 12,0 (72.7) 11, (68.2) (.6) 10 (.8) (63.2) (.9) 6120 (.4) (63.3) 20 (57.5) (.6) (54.3) (57.9) (51) () (52.1) (43.8) (49) (39.8) (.7) (.4) (42.2) (30.5) (38.4) (24.6) (34.2) A National Crane NTC 25

26 9,7 m 39,0 m (31.7 ft 128 ft) 1928 kg Stowed % (42 lb) # A 54-B 64-C -D 86-E 97-F 107-G 118-H 128 Mimum boom angle ( ) for dicated length (no load) 11 Maximum boom length (ft) at (no load) NOTE: ( ) Boom angles are degrees. #RCL operatg code. Refer to RCL manual for operatg structions. Liftg Capacities at Zero Degree Boom Angle Boom Angle A 54-B 64-C -D 86-E 101,000 (68.1) 88,0 (64) 78,0 63,200,0 29,0 (21.8) 11,0 (27.6) (71.6) (68.7) (56.7) 30,9 21,4 (37.3) 15,0 (23.6) 60 (38.8) NOTE: ( ) Reference radii. (73.4) (.1) 31,0 22,0 (51.3) 16,0 (43.9) 12,0 (.2) 42 (49.8) 39,0 39,0 39,0 (68.8) 31,9 22,0 (58.6) 16,0 12,8 (47) 10, (22.2) ,6 (78.7) 33,6 33,6 (72.5) 29,6 22,0 (64.2) 16,0 13,0 (.1) 10,0 () 82 (44.6) 66 (38.6) 42 (23.9) 33 (9.2) 10 (78.3) () (71.5) 20,000 17,0 (64.3) 13,200 10,0 (56.5) 84 (52.3) 6820 (47.8) (37.9) (31.8) 2810 (24.3) 21 (12.8) 0 (81.8) (77.1) (74.2) (71.2) 15,9 13,300 10,6 (61.5) 69 (54.4) 56 (.8) (46.6) (42.1) (31.6) 1730 (24.8) 12 (15.3) (78.6) 12,0 (76.1) (77.8) (78.9) 12,0 12,0 (73.2) (74.8) 13,0 11,0 (72.7) 10,0 10,0 () (68.2) (.6) (62) (.8) 71 (59.2) (63.2) (.9) (56) (.4) (63.3) (52.4) (57.5) (.6) (48.7) (54.3) (57.9) (44.7) (51) () (.5) (52.1) (.8) (43.8) (49) (30.4) (39.8) (.7) (.4) (42.2) (14.9) (30.5) (38.4) A 26

27 7,9 m 13,7 m (26 ft ft) 1928 kg (42 lb) % 36 **26 ft Length ft Length #4205 #4207 #4209 #4211 (.3) (73.6) (71.9) (.1) 4620 (66.7) (62.6) (58.3) 12 (56.1) 8 (53.8) 4 (51.2) 3 3 (77.3) (.8) (74.4) (72.9) (71.4) (69.9) (77) (.2) 36 (66.9) 3020 (.4) (71.7) 24 (63.8) (69.8) 19 (61.9) (67.9) (59.9) (.9) (57.8) (.6) (61.7) (77.4) (73.7) (71.7) (69.7) 37 (67.5) 3010 (.2) 23 (62.9) (58.1) 0 (.4) 0 (52.5) (53.5) 11 (59.5) 0 (57.1) 4 (54.7) M. boom angle for dicated length (no load) Max. boom length at boom angle (no load) 64 ft 64 ft NOTE: ( ) Boom angles are degrees A #RCL operatg code. Refer to RCL manual for structions. **26 ft. capacities are applicable to both 26' fixed and 26' tele extension. Boom extension capacity notes: ft and ft extension lengths may be used for sgle le liftg service. 2. Radii listed are for a fully extended boom with the boom extension erected. For ma boom lengths less than fully extended, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is configured. For boom angles not shown, use the ratg of the next lower boom angle. Warng: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and with-out advance warng. 3. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 4. Capacities listed are with outriggers properly extended and vertical jacks set only. National Crane NTC 27

28 9,7 m 39,0 m (31.7 ft 128 ft) 13 kg (3000 lb) % # A 54-B 64-C -D 86-E 97-F 107-G 118-H 128,000 (68.1) 92,2 (64), 63,4 46,300 31,6 (21.8) (71.6) (68.7) (56.7) 36,0 28,9 (37.3) 22,300 (23.6) (73.4) (.1) 36,9 29,0 (51.3) 23,0 (43.9) 18,0 (.2) 14,0,300,300,300 (68.8) 37,1 29,0 (58.6) 24,300 18,9 (47) 15,1 12,0 10,300 (22.2) 34, (78.7) 34, 34, (72.5) 30, 27, (64.2) 24,5 19,2 (.1) 15,4 () 12,0 (44.6) 10,0 (38.6) (23.9) *46 (9.2) 22,6 (78.3) 22,6 () 22,6 (71.5) 20,0 18,0 (64.3) 17,0 15,6 (56.5) 12,0 (52.3) 10,0 (47.8) 76 (37.9) 60 (31.8) 50 (24.3) *40 (12.8) 17,0 (77.1) 17,0 (74.2) 17,0 (71.2) 16,300 15, 14,000 (61.5) 12,8 11,000 (54.4) 92 (.8) 70 (46.6) 66 (42.1) 56 (31.6) 4 (24.8) 34 (15.3) (78.6) (76.1) 13,6 12,5 () 11,0 (62) 10,9 (59.2) (56) 79 (52.4) 60 (48.7) 50 (44.7) 49 (.5) 4200 (.8) (30.4) 3000 (14.9) (77.8) (73.2) 12,0 11,300 (68.2) 10,6 (.8) 10,000 (63.2) (.4) 8 (57.5) 60 (54.3) 50 (51) 4300 (43.8) 36 (39.8) 3 (.4) 20 (30.5) 21 (24.6) (74.8) (72.7) (.6) (.9) 78 (63.3) 00 (.6) 6300 (57.9) 50 () 51 (52.1) 40 (49) 30 (.7) 3200 (42.2) 20 (38.4) 22 (34.2) (16.8) (29.5) (23.7) *1 (15.8) Mimum boom angle ( ) for dicated length (no load) Maximum boom length (ft) at (no load) 97 NOTE: ( ) Boom angles are degrees. *Loads are structurally limited. #RCL operatg code. Refer to RCL manual for operatg structions. Liftg Capacities at Zero Degree Boom Angle Boom Angle A 54-B 64-C -D 86-E (27.6) (38.8) 48 (49.8) (81.8) NOTE: ( ) Reference radii

29 9,7 m 39,0 m (31.7 ft 128 ft) 13 kg Stowed % (3000 lb) # A 54-B 64-C -D 86-E 97-F 107-G 118-H ,8 (68.1) 91, (64) 78,9 62,300,1 30,0 (21.8) (71.6) (68.7) (56.7),0 28,1 (37.3) 21,0 (23.6) (73.4) (.1) 36,0 28,0 (51.3) 23,300 (43.9) 18,000 (.2) 14,200 39,0 39,0 39,0 (68.8) 36,6 29,200 (58.6) 23,0 18,4 (47) 14,6 11,8 90 (22.2) 33,6 (78.7) 33,6 33,6 (72.5) 29,6 26,6 (64.2) 24, 18,0 (.1) 15,000 () 12,1 (44.6) 10,1 (38.6) 00 (23.9) *4200 (9.2) (78.3) () (71.5) 20,000 18, (64.3) 16,6 15,2 (56.5) 12,0 (52.3) 10,0 (47.8) (37.9) 6 (31.8) 5 (24.3) *00 (12.8) (77.1) (74.2) (71.2) 15,9 14,0 13,6 (61.5) 12,0 10,6 (54.4) (.8) 74 (46.6) 6300 (42.1) (31.6) 30 (24.8) 3 (15.3) (78.6) (76.1) 13,0 12,2 () 11,4 (62) 10,6 (59.2) 9 (56) 76 (52.4) 60 (48.7) 50 (44.7) 46 (.5) 30 (.8) 32 (30.4) (14.9) 12,0 (77.8) 12,0 12,0 (73.2) 11,0 11,000 (68.2) 10,0 (.8) 90 (63.2) 9 (.4) 70 (57.5) 60 (54.3) (51) (43.8) 30 (39.8) 20 (.4) 2300 (30.5) 18 (24.6) (74.8) (72.7) (.6) (.9) (63.3) (.6) (57.9) 54 () 40 (52.1) 41 (49) 00 (.7) 29 (42.2) 24 (38.4) 2000 (34.2) (16.8) (29.5) (23.7) *8 (15.8) Mimum boom angle ( ) for dicated length (no load) Maximum boom length (ft) at (no load) 97 NOTE: ( ) Boom angles are degrees. *Loads are structurally limited. #RCL operatg code. Refer to RCL manual for operatg structions. Liftg Capacities at Zero Degree Boom Angle Boom Angle A 54-B 64-C -D 86-E 11,0 (27.6) 60 (38.8) 42 (49.8) (81.8) NOTE: ( ) Reference radii National Crane NTC 29

30 9,7 m 39,0 m (31.7 ft 128 ft) 13 kg (3000 lb) % Over Rear # A 54-B 64-C -D 86-E 97-F 107-G 118-H 128,000 (68.1) 92,2 (64), 63,4 46,300 31,6 (21.8) (71.6) (68.7) (56.7) 36,0 28,9 (37.3) 22,300 (23.6) (73.4) (.1) 36,9 29,0 (51.3) 24,000 (43.9) 20,000 (.2) 16,0,300,300,300 (68.8) 37,1 29,0 (58.6) 24,300 20,300 (47) 16,0 13,0 11,6 (22.2) 34, (78.7) 34, 34, (72.5) 30, 27, (64.2) 24,5 20,5 (.1) 17,0 () 14,1 (44.6) 11,0 (38.6) 10,200 (23.9) *46 (9.2) 22,6 (78.3) 22,6 () 22,6 (71.5) 20,0 18,0 (64.3) 17,0 15,0 (56.5) 14,0 (52.3) 12, (47.8) 10,0 (37.9) 76 (31.8) 60 (24.3) *40 (12.8) 17,0 (77.1) 17,0 (74.2) 17,0 (71.2) 16,300 15, 14,000 (61.5) 12,8 12,000 (54.4) 10,5 (.8) (46.6) 78 (42.1) 58 (31.6) 5 (24.8) *38 (15.3) (78.6) (76.1) 13,6 12,5 () 11,0 (62) 10,9 (59.2) 10,300 (56) 9200 (52.4) 79 (48.7) 60 (44.7) 00 (.5) (.8) 40 (30.4) 30 *20 (14.9) (77.8) (73.2) 12,0 11,300 (68.2) 10,6 (.8) 10,000 (63.2) (.4) 88 (57.5) 8 (54.3) 00 (51) (43.8) 40 (39.8) 00 (.4) 34 (30.5) 29 (24.6) (78.9) (74.8) (72.7) (.6) (.9) 78 (63.3) 00 (.6) 6300 (57.9) 50 () 51 (52.1) 46 (49) 41 (.7) (42.2) 3300 (38.4) 3000 (34.2) * (16.8) (29.5) 115 *10 (23.7) *1 120 (15.8) Mimum boom angle ( ) for dicated length (no load) Maximum boom length (ft) at (no load) 97 NOTE: ( ) Boom angles are degrees. *Loads are structurally limited. #RCL operatg code. Refer to RCL manual for operatg structions. Liftg Capacities at Zero Degree Boom Angle Boom Angle A 54-B 64-C -D 86-E (27.6) (38.8) 48 (49.8) (81.8) NOTE: ( ) Reference radii

31 9,7 m 39,0 m (31.7 ft 128 ft) 13 kg Stowed % (3000 lb) Over Rear # A 54-B 64-C -D 86-E 97-F 107-G 118-H ,8 (68.1) 91, (64) 78,9 62,300,1 30,0 (21.8) (71.6) (68.7) (56.7),0 28,1 (37.3) 21,0 (23.6) (73.4) (.1) 36,0 28,0 (51.3) 23,0 (43.9) 19,0 (.2) 15,0 39,0 39,0 39,0 (68.8) 36,6 29,200 (58.6) 23,0 19,0 (47) 16,300 13,0 11,1 (22.2) 33,6 (78.7) 33,6 33,6 (72.5) 29,6 26,6 (64.2) 24, 20, (.1) 16,0 () 13,0 (44.6) 11,4 (38.6) 82 (23.9) *4200 (9.2) (78.3) () (71.5) 20,000 18, (64.3) 16,6 15,0 (56.5) 13,9 (52.3) 11,0 (47.8) 10,000 (37.9) 72 (31.8) 6200 (24.3) *00 (12.8) (77.1) (74.2) (71.2) 15,9 14,0 13,6 (61.5) 12,0 11,6 (54.4) 10,200 (.8) (46.6) 00 (42.1) 50 (31.6) 40 (24.8) *00 (15.3) (78.6) (76.1) 13,0 12,2 () 11,4 (62) 10,6 (59.2) 10,000 (56) (52.4) 76 (48.7) 60 (44.7) 50 (.5) 40 (.8) 4200 (30.4) 30 * (14.9) 12,0 (77.8) 12,0 12,0 (73.2) 11,0 11,000 (68.2) 10,0 (.8) 90 (63.2) 9 (.4) (57.5) 70 (54.3) 60 (51) (43.8) 4300 (39.8) (.4) 31 (30.5) (74.8) (72.7) (.6) (.9) (63.3) (.6) (57.9) 54 () 40 (52.1) 40 (49) 30 (.7) 34 (42.2) 30 (38.4) * (24.6) (16.8) (34.2) (29.5) *16 (23.7) *8 (15.8) Mimum boom angle ( ) for dicated length (no load) Maximum boom length (ft) at (no load) 97 NOTE: ( ) Boom angles are degrees. *Loads are structurally limited. #RCL operatg code. Refer to RCL manual for operatg structions. Liftg Capacities at Zero Degree Boom Angle Boom Angle A 54-B 64-C -D 86-E 11,0 (27.6) 60 (38.8) 42 (49.8) (81.8) NOTE: ( ) Reference radii National Crane NTC 31

32 7,9 m 13,7 m (26 ft ft) 13 kg (3000 lb) % **26 ft Length ft Length #5 #7 #9 #1011 (.3) (73.6) (71.9) (.1) (66.7) (62.6) (58.3) 34 (56.1) 3000 (53.8) 24 (51.2) 2000 (48.4) 10 (.5) 1200 (42.5) 8 (39.3) 5 (.8) 3 (77.4) (73.7) (71.7) 46 (69.7) 40 (67.5) 41 (.2) 00 (62.9) 30 (58.1) 29 (.4) 24 (52.5) 19 (49.5) 10 (46.3) 1 (42.7) 0 (38.9) (77.3) (.8) (74.4) (72.9) (71.4) (69.9) (66.9) (.4) (63.8) (61.9) 32 (59.9) 3000 (57.8) 20 (.6) 20 (53.5) 2000 (51.2) 16 (48.7) 1300 (46) 0 0 (.4) 4 3 (77) (.2) (71.7) (69.8) (67.9) (.9) 24 (61.7) 20 (59.5) 20 (57.1) 2200 (54.7) 10 (52.1) 14 (49.1) 10 (.9) 0 (42.3) Boom extension capacity notes: ft. and ft. extension lengths may be used for sgle le liftg service. 2. Radii listed are for a fully extended boom with the boom extension erected. For ma boom lengths less than fully extended, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is configured. For boom angles not shown, use the ratg of the next lower boom angle. WARNING: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 3. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 4. Capacities listed are with outriggers properly extended and vertical jacks set only. 1 0 (38.2) M. boom angle for dicated length (no load) Max. boom length at boom angle 64 ft 64 ft (no load) NOTE: ( ) Boom angles are degrees #RCL operatg code. Refer to RCL manual for structions. *Loads are structurally limited. **26 ft. capacities are applicable to both 26' fixed and 26' tele extension. 32

33 7,9 m 13,7 m (26 ft ft) 13 kg (3000 lb) % Over Rear M. boom angle for dicated length (no load) Max. boom length at boom angle (no load) **26 ft Length ft Length #6 #8 #1010 #1012 (.3) (73.6) (71.9) (.1) (66.7) (62.6) (58.3) 30 (56.1) 36 (53.8) 31 (51.2) 20 (48.4) 2 (.5) 10 (42.5) 10 (39.3) 9 (.8) 6 (32.1) 3 (77.4) (73.7) (71.7) 46 (69.7) 40 (67.5) 41 (.2) 00 (62.9) (58.1) 30 (.4) 20 (52.5) 25 (49.5) 21 (46.3) 16 (42.7) 1200 (38.9) 8 (34.8) 4 (30) (77.3) (.8) (74.4) (72.9) (71.4) (69.9) (66.9) (.4) (63.8) (61.9) 32 (59.9) 3000 (57.8) 20 (.6) (53.5) 2300 (51.2) 20 (48.7) 10 (46) (.4) 0 6 (33.9) ft 64 ft (77) (.2) (71.7) (69.8) (67.9) (.9) 24 (61.7) 20 (59.5) 20 (57.1) 2300 (54.7) 22 (52.1) 2 (49.1) 10 (.9) *10 (42.3) *0 (38.2) *0 (33.9) NOTE: ( ) Boom angles are degrees #RCL operatg code. Refer to RCL manual for structions. *Loads are structurally limited. **26 ft capacities are applicable to both 26 ft fixed and 26 ft tele extension Boom extension capacity notes: ft and ft extension lengths may be used for sgle le liftg service. 2. Radii listed are for a fully extended boom with the boom extension erected. For ma boom lengths less than fully extended, the rated loads are deter med by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is configured. For boom angles not shown, use the ratg of the next lower boom angle. Warng: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 3. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 4. Capacities listed are with outriggers properly extended and vertical jacks set only. National Crane NTC 33

34 9,7 m 39,0 m (31.7 ft 128 ft) 13 kg (3000 lb) % # A 54-B 64-C -D 86-E 97-F 107-G 118-H ,000 (68.1) 89,6 (64) 79,6 63,5 46,1 28,5 (21.8) (71.6) (68.7) (56.7) 29,5 20,0 (37.3) 15,200 (23.6) (73.4) (.1) 30,000 21, (51.3) 15,6 (43.9) 12,000 (.2) 94,300 34, (78.7),300 34, 22,6 (78.3),300 34, 22,6 17,0 (68.8) (72.5) () (77.1) (78.6) 30,2 30, 22,6 17,0 (71.5) (74.2) (76.1) (77.8) (78.9) 21,300 21,0 20,0 17,0 (58.6) (64.2) (71.2) 15,8 16,0 16,1 16,200 (64.3) (73.2) (74.8) 12,2 12,0 12,0 12,5 12,0 12,0 (47) (.1) (72.7) ,0 10, 10,1 () (56.5) (61.5) () (68.2) (.6) (44.6) (52.3) (62) (.8) (22.2) (38.6) (47.8) (54.4) (59.2) (63.2) (.9) (.8) (56) (.4) (63.3) (23.9) (37.9) (46.6) (52.4) (57.5) (.6) (9.2) (31.8) (42.1) (48.7) (54.3) (57.9) 20 (24.3) 20 (12.8) (31.6) 16 (24.8) 11 (15.3) 28 (44.7) 2230 (.5) 10 (.8) 12 (30.4) (51) (43.8) 12 (39.8) 8 (.4) 510 (30.5) 20 () 2300 (52.1) 17 (49) 1310 (.7) 0 (42.2) 5 (38.4) Mimum boom angle ( ) for dicated length (no load) Maximum boom length (ft) at boom angle (no load) 86 NOTE: ( ) Boom angles are degrees. *Loads are structurally limited. #RCL operatg code. Refer to RCL manual for operatg structions. Liftg Capacities at Zero Degree Boom Angle Boom Angle A 54-B 64-C -D 86-E (27.6) (38.8) (49.8) (81.8) NOTE: ( ) Reference radii A 34

35 9,7 m 39,0 m (31.7 ft 128 ft) 13 kg Stowed % (3000 lb) # A 54-B 64-C -D 86-E 97-F 107-G 118-H 128,0 (68.1) 88,0 (64) 78,0 62,0,000 27,0 (21.8) (71.6) (68.7) (56.7) 28,0 19,0 (37.3) (23.6) (73.4) (.1) 29,0 20,0 (51.3) 15,0 (43.9) 11,0 (.2) 88 39,0 39,0 39,0 (68.8) 29,0 20,0 (58.6) 15,0 11,0 (47) (22.2) 33,6 (78.7) 33,6 33,6 (72.5) 29,6 21,0 (64.2) 15,0 11,9 (.1) 9420 () 74 (44.6) 5920 (38.6) (23.9) 2820 (9.2) (78.3) () (71.5) 20,000 15,0 (64.3) 12, (56.5) 7620 (52.3) (47.8) (37.9) 3010 (31.8) 2300 (24.3) 16 (12.8) (77.1) (74.2) (71.2) 15,8 12, (61.5) 6210 (54.4) 49 (.8) 39 (46.6) 31 (42.1) (31.6) 12 (24.8) 820 (15.3) (78.6) (76.1) 12, () 78 (62) 6310 (59.2) (56) (52.4) 32 (48.7) 25 (44.7) 1930 (.5) 10 (.8) 9 (30.4) ,0 (77.8) 12,0 12,0 (73.2) 11,0 98 (68.2) 78 (.8) (63.2) 5120 (.4) 4120 (57.5) 32 (54.3) 25 (51) (43.8) 9 (39.8) 5 (.4) (78.9) (74.8) (72.7) (.6) (.9) (63.3) 4200 (.6) 33 (57.9) 26 () 20 (52.1) 1520 (49) 10 (.7) 6 (42.2) Mimum boom angle ( ) for dicated length (no load) Maximum boom le ngth (ft.) a t b o om a ngle (no lo a d ) 86 NOTE: ( ) Boom angles are degrees. *Loads are structurally limited. #RCL operatg code. Refer to RCL manual for operatg structions. Liftg Capacities at Zero Degree Boom Angle Boom Angle A 54-B 64-C -D 86-E 11,0 (27.6) 60 (38.8) NOTE: ( ) Reference radii. 42 (49.8) (81.8) 0943A National Crane NTC

36 7,9 m 13,7 m (26 ft ft) 13 kg (3000 lb) % **26 ft Length ft Length #1205 #1207 #1209 #1211 (.3) (73.6) (71.9) (.1) 4230 (66.7) (62.6) (58.3) 0 (56.1) 5 (53.8) 3 3 (77.3) (.8) (77.4) (74.4) (72.9) (73.7) (71.4) (71.7) (69.9) (77) 42 (69.7) (.2) (67.5) (66.9) (.2) (.4) (71.7) 2 21 (62.9) (63.8) (69.8) (61.9) (67.9) (58.1) (59.9) (.9) (.4) (57.8) (.6) (61.7) 9 (59.5) 0 (57.1) Boom extension capacity notes: ft and ft extension lengths may be used for sgle le liftg service. 2. Radii listed are for a fully extended boom with the boom extension erected. For ma boom lengths less than fully extended, the rated loads are deter med by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is configured. For boom angles not shown, use the ratg of the next lower boom angle. Warng: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 3. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 5. Capacities listed are with outriggers properly extended and vertical jacks set only. M. boom angle for dicated length (no load) Max. boom length at boom angle (no load) 64 ft 64 ft NOTE: ( ) Boom angles are degrees A #RCL operatg code. Refer to RCL manual for structions. **26 ft. capacities are applicable to both 26' fixed and 26' tele extension. 36

37 Specifications Superstructure Boom 9,7 m 39,0 m (31.7 ft 128 ft) five-section boom with a maximum tip height of 54,6 m (179 ft). Includes proportional extension via multi-stage hydraulic cylder and cable operation, four-plate, high-strength steel construction, three-sheave, quick reeve boom nose and Easy-Glide wear pads. Boom elevation One (1) double-actg, hydraulic cylder with tegral holdg valve with tegral pressure transducers provides elevation from -8 to +8. Rated Capacity Limitg (RCL) and anti-two-block (ATB) systems Graphical display capacity limiter and anti-two-block system with audio visual warng and crane function lockout. The graphical display is a 178 mm (7 ) color and polarized screen for real-time display of boom angle, length, radius, tip height, maximum permissible load, load dication and warng of impendg overload or anti-two-block condition. Work area defition system (WADS) allowg operator defable non-lockout warng limits for crane operations, and CANbus sensors and hard-wired ATB circuit routed externally to the boom. Outrigger monitorg system (OMS) to sense the configuration of the outriggers and aid the operator selectg an appropriate setup. On-board setup and diagnostics for RCL sensors allow for improved service and an event recorder to protect your vestment. Crane Control System Fully tegrated RCL and CANbus crane control system for maximum performance. Real-time diagnostics for truck chassis data such as enge regeneration, fuel level, enge coolant, oil pressure, enge RPM and battery voltage. On-board setup and diagnostics for all sensors and control modules allowg for improved service and little need for a laptop or diagnostic cables. Fault codes to quickly identify service needs and event recorder to protect your vestment. Automotive grade, fully wire-harnessed 12VDC electrical system usg state-of-the-art sealed connectors and control modules. Dual-tone backup and outrigger motion alarm located at rear of mache. LED marker and triple ID lights. Operator cab and controls Cab structure: rigid galvanealed steel structure, well sulated, offerg optimum operator visibility and comfort. Equipped with tiltg cab feature from horizontal to +2, tted safety glass, fixed front wdow with wdshield wiper and washer, slidg skylight wdow with wdshield wiper, slidg left side glass door, slidg right side wdow for ventilation w/ safety grille, tiltg rear wdow for ventilation, four way adjustable, cushioned seat and armrests with seat belt, diesel-fired warm-water heater with air ducts at operators, left side of cab and front dash standard, hydraulic-powered air conditioner standard, circulation fan, bubble level, adjustable sun visor, dome light, cup holder, fire extguisher, load chart bder with tear-proof paper load charts and operator manual. Armrest control functions are arranged per ASME B30.5: Two sgle axis electric joystick controllers for swg, boom telescope, ma hoist, auxiliary hoist (optional), boom lift, warng horn button, swg park brake switch, hoist rotation dicator, tilt cab up/down, ma hoist high/low speed switch, and aux hoist high/low speed switch (optional). Outrigger controls: front console mounted electronic keypad allowg the operator to activate all horizontal beams and vertical jacks. Pre-selection capabilities to easily activate more than one function for ease of setup. Foot controls: enge throttle (electronic), dynamic swg brake (electronic), boom telescope (electronic, if equipped with aux hoist option). Front console controls and dicators for rated capacity limiter display, outriggers, enge ignition key, emergency stop switch, and RCL override keyswitch (momentary). 12VDC power outlet. Overhead console controls and dicators for heater, A/C and fan speed, wdshield wiper and washer, skylight wiper, cab mounted work lights, crane function power, radio remote power. Removable counterweight Hydraulically removable counterweight system consistg of (2) vertical double-actg hydraulic cylders equipped with holdg valves to dependently raise and lower the desired counterweight slabs. Controls can be activated at both the left and right side of turret near the counterweight for ease of activation durg counterweight p reconfiguration. Counterweight consists of (3) slabs for (4) unique load chart configurations: (3) slabs stalled on turret: (1) x [3000 lb], (2) x [12 lb] (2) slabs stalled on turret: (1) x [3000 lb], (1) x [12 lb] (1) slab stalled on turret: (1) x [3000 lb] (0) slabs stalled on turret: no slabs stalled When not use, one or all of the slabs can be stowed on top of the front outrigger box. One or all of the slabs can also be removed from the crane by usg the crane itself after stowg on front outrigger box first. National Crane NTC 37

38 Specifications Slewg Contuous 36 rotation usg (1) low speed, high torque motor with a manually adjustable swg adjustment valve tegrated to the hydraulic motor control manifold mounted to a planetary reduction gear. A proportional electronic brake pedal located the operator cab allows for the dynamic application of the multi-disk swg brake circuit. A separate sprg-applied, hydraulic-released brake for disablg rotation can be activated from the left-hand seat armrest. Free-swg functionality is disabled when usg the optional crane radio remote control. Maximum rotation speed of 2 RPM. Hydraulic system Efficient closed-center, load sense hydraulics system featurg load-sharg technology allowg for smooth multifunction operation of all crane functions. One (1) SAE-C mounted, 130cc axial piston pump for all functions and optimized system performance. Shaft put of 2200 RPM generatg 286 lpm (76 gpm) max flow at 320 bar (40 psi) max operatg pressure. 1 L ( gal) hydraulic reservoir with SAE o-rg connections and tegrated butterfly shut-off valve for easy matenance. SAE o-rg hydraulic fittgs and hoses throughout. Boom lift, boom telescope, ma and aux hoist(s) and vertical outrigger jacks are all equipped with counterbalance valves for controlled movement and load holdg. Hydraulic oil cooler: standard electric fan, plate and f style oil cooler mounted the rear of the superstructure to remove heat from the hydraulic oil under heavy operatg conditions. Electrical system Automotive grade, fully wire harnessed 12VDC electrical system usg state-of-the-art sealed connectors and control modules. Dual-tone backup and outrigger motion alarm located at rear of mache. LED marker and triple ID lights. Lower Chassis mountg Torsion-resistant, high-strength steel sub frame attached usg high-strength steel mountg brackets that are welded to the sub-frame and bolted to the truck chassis usg Huck bolts to ensure a secure and matenance-free connection. Rear bumper under ride protection standard. Fixed boom rest mounted to front outrigger box and fabricated from structural steel. Outriggers Out and down style outriggers at both the front and rear with dividual control of each horizontal beam extension and vertical jack cylder. Each outrigger jack is equipped with a 8 mm (20 ) polymeric outrigger float standard. Horizontal beams are non-proportional and can be pned (4) different configurations for operation. Front outriggers are angled toward the truck cab, elimatg the need for an SFO. Ground level control stations located at the left and right side for all vertical jacks and only the horizontal beams for each station. Operator cab features an electronic keypad mounted on the front console to control all outrigger functions. % span: Front = 7,09 m (23 ft 3 ) Rear = 7,39 m (24 ft 3 ) % span: Front = 5,9 m (19 ft 4 ) Rear = 6,12 m (20 ft 1 ) % span: Front = 4,72 m (15 ft 6 ) Rear = 4, m (16 ft 1 ) 0% span: Front and Rear = 2,39 m (7 ft 10 ) Outrigger monitorg system for horizontal beam extension is standard. Inverted cylder rods for vertical outrigger jack cylders for best protection of chromed rod. Optional sgle front outrigger (SFO) is available for heavy front axle mountg configurations. 38

39 Specifications Optional items Operator aids > Five-function wireless radio remote control of approximately m (2 ft) (NB5R) Telescopic offsettable jib > 7,9 m 13,7 m (26 ft ft) telescopg boom extension (side fold for stowg), cludes 5,8 m (19 ft) manual pull out section > Max tip height of 54,6 m (179 ft) > Offsets of and 3 > RCL calibration for future jib option Fixed offsettable jib > 7,9 m (26 ft.) fixed boom extension (side fold for stowg) > Max tip height of 49,7 m (162.9 ft) > Offsets of and 3 > RCL calibration for future jib option Hook blocks > Sgle sheave, 18,1 t (20 USt) quick-reeve hook block for 2-3 part reevg [186 kg (410 lb)] > Triple sheave, 36,3 t ( USt) quick-reeve hook block for 4-7 part reevg cludg auxiliary sheave case assembly (272 kg [0 lb]) > Five sheave, 49,9 t ( USt) quick-reeve hook block for 8-10 part reevg cludg auxiliary sheave case assembly (498 kg [1098 lb]) Sgle Front Outrigger > 63,5 m (25 ) vertical stroke > Available for certa mountg configurations Alumum outrigger floats > 610 mm (24 ) alumum floats lieu of the standard 0 mm (19.7 ) polymeric floats Auxiliary hoist > A second turret-mounted hoist located to the rear of the standard ma hoist > Standard with rotation-resistant wire rope and round, top-swivel downhaul weight Personnel handlg platforms > (2) person steel, non-sulated, platform options > Rotatg and yoke-style options > Capacities up to 544,3 kg (1200 lb) on ma boom and 226,8 kg (0 lb) on jib > Platform test weight sets available for each > Compliant to ASME B30.23 requirements K synthetic rope > 18 mm (0.71 ) 137,2 m (4 ft) K synthetic hoist rope ( lieu of standard rope) > Available for either ma, aux or both hoists > % lighter than steel wire rope with same available lepull > Easy handlg/reevg and stallation > Reduces number of change outs due to mitigation of kkg, birdcagg or damage from divg > Corrosion resistant no rustg, no lubrication requirements National Crane NTC 39

40 Specifications Ma and (optional) auxiliary hoist(s) Two-speed displacement, bent-axis piston motor drivg a planetary gearset and a grooved drum with cable tensioner/follower, drum rotation dicator and last layer and mimum wrap dicators. Parts of Le Max boom length (ft) at max elevations with stated riggg and load block and ground level 1 part le 173 (cludes ft ext.) 2 part le 3 part le 4 part le 5 part le 6 part le 7 part le 8 part le 9 part le 10 part le Low speed lift (lb) 11,2 22,0 33,0,000 56,2 67,0 78,0,000, ,000 High speed lift (lb) 00 10,000 15,000 20,000 25,000 30,000,000,000,000,000 Le Pulls and Reevg Information Hoists Cable specs. Permissible le pulls Nomal cable length Ma Ma and Auxiliary Ma and Auxiliary 16 mm (5/8 ) Dyform 34 LR Rotation Resistant (non-rotatg) M. Breakg Strength 56,420 lb 16 mm (5/8 ) 6x19 Class EEIPS, IWRC M. Breakg Strength,0 lb 18 mm Synthetic K- Hoist Rope (ISO) M. Breakg Strength 63,0 lb 11,2 lb* 4 ft 11,2 lb* 4 ft 12,7 lb* 463 ft The approximate weight of 5/8 wire rope is 1.0 lb/ft. The approximate weight of 18 mm synthetic rope is 0.16 lb/ft. *With certa boom and hoist tackle combations, the allowable le pull may be limited by hoist performance. Refer to Hoist Performance table for lift planng to ensure adequate hoist performance on drum rope layer required. Hoist Performance Wire rope layer Hoist le pulls Two speed hoist Low Available lb High Available lb Drum capacity (ft) Layer Total 1 15, , , , , *Refer to Le Pulls and Reevg Information table for max. liftg capacity of wire rope. Synthetic rope layer height may vary and may reduce available le pull per layer. Weight Reductions for Load Handlg Devices Auxiliary boom nose 32.2 kg (71 lb) Hook blocks and headache balls USt, 5-sheave (14 sheave) CE kg (1098 lb)+ USt, 3-sheave (12 sheave) kg (0 lb)+ 20 USt, 1-sheave kg (0 lb)+ 7 USt overhaul ball kg (2 lb)+ + Refer to ratg plate for actual weight When liftg over boom extension, deduct total weight of all load handlg devices reeved over ma boom nose directly from boom extension capacity. NOTE: All load handlg devices and boom attachments are considered part of the load and suitable allowances MUST BE MADE for their combed weights. Weights are for Manitowoc furnished equipment.

41 Symbols glossary Axles Drive Heavy duty jib Boom Electrical system Hoist Rotation Boom elevation Enge H Hook block Speed Boom extension Extension Hydraulic system Steerg Boom length Frame Insert Suspension Boom nose Fuel tank capacity Lights Swg Brakes Gear Oil Tires Operators station Grade Outrigger controls Transmission Counterweight Height (no max) Outriggers National Crane NTC 41

42 Notes 42

43 Notes National Crane NTC 43

44 Manitowoc Cranes Regional headquarters Americas Manitowoc, Wiscons, USA Tel: Fax: Shady Grove, Pennsylvania, USA Tel: Fax: Europe, Middle East, Africa Dardilly, France - TOWERS Tel: +33 (0) Fax: +33 (0) Wilhelmshaven, Germany - MOBILE Tel: +49 (0) Fax: +49 (0) Cha Shanghai, Cha Tel: Fax: Greater Asia-Pacific Sgapore Tel: Fax: Dubai, UAE Tel: Fax: /79 This document is non-contractual. Constant improvement and engeerg progress make it necessary that we reserve the right to make specification, equipment, and price changes without notice. Illustrations shown may clude optional equipment and accessories and may not clude all standard equipment The Manitowoc Company, Inc. Form No. NTC PG Part No /2M/0217

National Crane Series NBT60 Product Guide

National Crane Series NBT60 Product Guide National Crane Series NBT Product Guide ASME B30.5 Imperial % Features 39,01 m (128 ft) five-section full power boom 54,4 t ( USt) at 2,44 m (8 ft) Self-lubricatg Easy Glide wear pads Hydraulically removable

More information

Boom truck 55 tons. national nbt50/55. BOOM LENGTHS: 32 to 128 ft JIB LENGTHS: 26 to 45 ft JIB OFFSETS: 0-30

Boom truck 55 tons. national nbt50/55. BOOM LENGTHS: 32 to 128 ft JIB LENGTHS: 26 to 45 ft JIB OFFSETS: 0-30 Boom truck tons national nbt/ BOOM LENGTHS: 32 to 128 ft JIB LENGTHS: 26 to 45 ft JIB S: 0-30 NOTES: National Crane Series NBT Product Guide ASME B30.5 Imperial % Features 31,1 m (102 ft) four-section

More information

National Crane Series NBT45 Product Guide

National Crane Series NBT45 Product Guide National Crane Series NBT45 Product Guide ASME B.5 Imperial 85% Features,8 t (45 USt) ratg 49,1 m (161 ft) five-section boom Self-lubricatg Easy Glide wear pads 41 kg ( lb) tailswg counterweight Features

More information

National Crane Series NBT45 Product Guide

National Crane Series NBT45 Product Guide National Crane Series NBT45 Product Guide ASME B.5 Imperial 85% Features,8 t (45 USt) ratg 49,1 m (161 ft) five-section boom Self-lubricatg Easy Glide wear pads 41 kg ( lb) tailswg counterweight Features

More information

National Crane Series NBT40

National Crane Series NBT40 National Crane Series NBT40 Product Guide Features 36,3 t (40 USt) ratg 43,3 m (142 ft) five-section boom Self-lubricatg Easy Glide wear pads 862 kg (1900 lb) tailswg counterweight Features National Crane

More information

Three-position, out and down style outriggers with lighter polymeric floats

Three-position, out and down style outriggers with lighter polymeric floats NBT-1 Capacity: USt (36,3 t) ratg Boom: 142 ft (43,3 m) five-section boom Max tip height ma boom: 1 ft (45,72 m) Max tip height ma boom with jib: 4 ft (62,2 m) Several boom length options providg work

More information

LOAD CHARTS NTC55 85% STABILITY ON OUTRIGGERS

LOAD CHARTS NTC55 85% STABILITY ON OUTRIGGERS LOAD CHARTS NTC 5% STABILITY ON OUTRIGGERS 0443 SERIAL NUMBER GA24146 1 TABLE OF CONTENTS GENERAL NOTES... 6-7 WT. REDUCTIONS / LINE PULLS & REEVING INFO / HOIST PERFORMANCE... LIFTING AREA DIAGRAM / BASKET

More information

Boom truck 36 tons. national series BOOM LENGTHS: 31ft to 127ft JIB LENGTHS: 31ft JIB OFFSETS:

Boom truck 36 tons. national series BOOM LENGTHS: 31ft to 127ft JIB LENGTHS: 31ft JIB OFFSETS: Boom truck 3 tons national series : ft to 7ft JIB : ft JIB OFFSETS: NOTES: portland office: 53.23.11 seattle office: 2.74.4 features Why Buy a National Crane Series? 3 USt (32. t) Rating The provides a

More information

LOAD CHARTS NBT45 85% STABILITY ON OUTRIGGERS

LOAD CHARTS NBT45 85% STABILITY ON OUTRIGGERS LOAD CHARTS NBT45 85% STABILITY ON OUTRIGGERS 295995 SERIAL NUMBER 1 2 TABLE OF CONTENTS GENERAL NOTES...4-5 LIFTING AREA DIAGRAM / LINE PULLS & REEVING INFO / HOIST PERFORMANCE... 6 RANGE DIAGRAM w/ EXTENSION...7

More information

TMS500E. product guide. contents. features 40 ton (40 mt) Capacity. Truck Mounted Crane

TMS500E. product guide. contents. features 40 ton (40 mt) Capacity. Truck Mounted Crane TMS0E product guide features ton ( mt) Capacity 29 ft.-95 ft. (8.8-29 m) 4 section, full power sequenced synchronized boom 26 ft.- ft. (7.9-13.7 m) offsettable telescopic swingaway extension Optional 26

More information

TECHNICAL SPECIFICATIONS

TECHNICAL SPECIFICATIONS 40142 40142 SIDE VIEW DIAGRAM Maximum Vertical Reach 207'/63,1 m Working Area 360 Degrees Lifting Capacity 80,000 lbs/36 287 kg Boom Length 142 /43,3 m Crane Weight (Standard) 40,300 lbs/18 280 kg Jib

More information

400B Product Guide. Features. ASME B30.5 Imperial 85% 9,1 t (10 USt) rating. Multiple mounting configurations. 17,1 m (56 ft) three-section boom

400B Product Guide. Features. ASME B30.5 Imperial 85% 9,1 t (10 USt) rating. Multiple mounting configurations. 17,1 m (56 ft) three-section boom 4B Product Guide ASME B3.5 Imperial 85% Features 9,1 t (1 USt) rating 17,1 m (56 ft) three-section boom Multiple mounting configurations Internal anti-two block NATIONAL CRANE 4B The 4B Series delivers

More information

40142R TECHNICAL SPECIFICATIONS 40142R SIDE VIEW DIAGRAM. Maximum Vertical Reach. Powered Boom Sections 5 Overall Height. 210'/64 m Working Area

40142R TECHNICAL SPECIFICATIONS 40142R SIDE VIEW DIAGRAM. Maximum Vertical Reach. Powered Boom Sections 5 Overall Height. 210'/64 m Working Area 40142R 40142R SIDE VIEW DIAGRAM Maximum Vertical Reach 210'/64 m Working Area 360 Degrees Lifting Capacity 80,000 lbs/36 287 kg Boom Length 142 /43,3 m Crane Weight (Standard) 41,700 lbs/18 915 kg Jib

More information

600H Product Guide. Features. ASME B30.5 Imperial 85% Standard RCL System. 18,1 t (20 USt) rating

600H Product Guide. Features. ASME B30.5 Imperial 85% Standard RCL System. 18,1 t (20 USt) rating 6H Product Guide ASME B3.5 Imperial 85% Features 18,1 t (2 USt) rating Five boom options available from 15 m (49 ft) to 27,42 m (9 ft) Multiple outrigger positions Standard RCL System Internal anti-two

More information

National Crane Series 800H

National Crane Series 800H National Crane Series 8H Data Sheet Features 3,48 m (1 ft) four-section boom 2,86 t (23 USt) rating Self-lubricating Easy Glide wear pads Dimensions 85 mm (31.69") 247 mm (94.") Maximum transport width

More information

National Crane Series NBT36

National Crane Series NBT36 National Crane Series NBT36 Product Guide Features 32,7 t (36 USt) rating 38,7 m (127 ft) five-section boom Self-lubricating Easy Glide wear pads Features National Crane Series NBT36 32,7 t (36 USt) maximum

More information

Dimensions Turning Radius (6.4m) 2 Wheel Steer /2 (3.6m) 4 Wheel Steer

Dimensions Turning Radius (6.4m) 2 Wheel Steer /2 (3.6m) 4 Wheel Steer INDUSTRIAL CRANE Dimensions Turng 20 11 (6.4m) 2 Wheel Steer 11 10-1/2 (3.6m) 4 Wheel Steer 14'0" 14 0 (4267) (4267) 12' 1-3/4" (3.7m) 7' 8-1/2" (2350) 6' 3-1/4" (1911) TAILSWING Note: ( ) Reference dimensions

More information

TECHNICAL SPECIFICATIONS

TECHNICAL SPECIFICATIONS 45127 45127 SIDE VIEW DIAGRAM Maximum Vertical Reach Working Area Lifting Capacity Boom Length Crane Weight (Standard) Jib Lengths Winch Bare Drum Pull 192'/58,5 m 360 Degrees 90,000 lbs/40 823 kg 127

More information

ROUGH TERRAIN HYDRAULIC CRANE RT875BXL

ROUGH TERRAIN HYDRAULIC CRANE RT875BXL ROUGH TERRAIN HYDRAULIC CRANE RT875BXL Dimensions TAILSWING 14' (4280) 24' (7315) 10' 4" (31) TRACK 8' 4-1/2" (2553) 17' 4" (5283) 26' 6-1/2" (8090) 24' 11" (7595) 43' (13 106) 1' 3" (381) 7' 3" (2210)

More information

GIUFFRE.COM. National Crane 500E2 Series GIUFFRE BROS CRANES INC. Product Guide

GIUFFRE.COM. National Crane 500E2 Series GIUFFRE BROS CRANES INC. Product Guide National Crane 5E2 Series Product Guide Features 16,3 t (18 USt) rating 21,6 m (71 ft) three-section boom Self-lubricating Easy Glide wear pads Internal anti-two block Features National Crane Series 5E2

More information

TMS9000E Product Guide

TMS9000E Product Guide TMS9000E Product Guide Features 90 t (110 USt) capacity 11,2 m - 43,4 m (36 ft - 142 ft) five-section full power boom Patented TWIN-LOCK boom pinning system 10 m - 17 m (33 ft - 56 ft) bi-fold lattice

More information

TMS500E. product guide. contents. features 40 ton (40 mt) Capacity. Truck Mounted Crane

TMS500E. product guide. contents. features 40 ton (40 mt) Capacity. Truck Mounted Crane product guide features ton ( mt) Capacity 29 ft.-95 ft. (8.8-29 m) 4 section, full power synchronized boom 26 ft.- ft. (7.9-13.7 m) offsettable telescopic swingaway extension Optional 8,4 lb. (3837 kg)

More information

National Crane Series NBT45

National Crane Series NBT45 National Crane Series NBT45 Product Guide Features ř 40,8 t (45 USt) rating ř 43,3 m (142 ft) five-section boom ř Self-lubricating Easy Glide wear pads ř 2041 kg (4500 lb) tailswing counterweight Features

More information

50105R TECHNICAL SPECIFICATIONS 50105R SIDE VIEW DIAGRAM. Powered Boom Sections 4 Overall Height

50105R TECHNICAL SPECIFICATIONS 50105R SIDE VIEW DIAGRAM. Powered Boom Sections 4 Overall Height 50105R 50105R SIDE VIEW DIAGRAM Maximum Vertical Reach Working Area Lifting Capacity Boom Length Crane Weight (Standard) Jib Lengths Winch Bare Drum Pull 164'/50 m 360 Degrees 100,000 lbs/45,359 kg 105

More information

32117R TECHNICAL SPECIFICATIONS 32117R SIDE VIEW DIAGRAM. Maximum Vertical Reach. Powered Boom Sections 5 Overall Height

32117R TECHNICAL SPECIFICATIONS 32117R SIDE VIEW DIAGRAM. Maximum Vertical Reach. Powered Boom Sections 5 Overall Height 32117R 32117R SIDE VIEW DIAGRAM Maximum Vertical Reach 153'/46,6 m Working Area 180 Degrees Standard (360 Optional) Lifting Capacity 64,000 lbs/29 030 kg Boom Length 117 /35,6 m Crane Weight (Standard)

More information

View thousands of Crane Specifications on FreeCraneSpecs.com

View thousands of Crane Specifications on FreeCraneSpecs.com 40142 40142 SIDE VIEW DIAGRAM Maximum Vertical Reach Working Area Lifting Capacity Boom Length Crane Weight (Standard) Jib Lengths Winch Bare Drum Pull 201'/61.3 m 360 Degrees 80,000 lbs/36,287 kg 142

More information

30' BOOM 13' 8" (4166) 24' BOOM 11' 8" (3556) 1' 8-1/2" (521) 3' 8-1/2" (1129) 15' 9-1/2" (4813) 17' 9-1/2" (5421)

30' BOOM 13' 8 (4166) 24' BOOM 11' 8 (3556) 1' 8-1/2 (521) 3' 8-1/2 (1129) 15' 9-1/2 (4813) 17' 9-1/2 (5421) INDUSTRIAL CRANE Dimensions 10' 10" (3302) 9' 4" (2845) 6' (1829) TRACK 7' (2134) A B 24' BOOM 11' 8" (3556) 1' 8-1/2" (521) 30' BOOM 13' 8" (4166) 3' 8-1/2" (1129) C 15' 9-1/2" (4813) 17' 9-1/2" (5421)

More information

30105F TECHNICAL SPECIFICATIONS 30105F SIDE VIEW DIAGRAM. Maximum Vertical Reach. Powered Boom Sections 4 Overall Height

30105F TECHNICAL SPECIFICATIONS 30105F SIDE VIEW DIAGRAM. Maximum Vertical Reach. Powered Boom Sections 4 Overall Height 30105F 30105F SIDE VIEW DIAGRAM 6 Maximum Vertical Reach 162'/49 m Working Area 180 Degrees Standard (360 Optional) Lifting Capacity 60,000 lbs/27 216 kg Boom Length 105 /32 m Crane Weight (Standard) 28,160

More information

product guide contents features 40 ton (40 mt) Capacity Truck Mounted Crane 29 ft.-95 ft. ( m) 4 section, full power synchronized boom

product guide contents features 40 ton (40 mt) Capacity Truck Mounted Crane 29 ft.-95 ft. ( m) 4 section, full power synchronized boom product guide features ton ( mt) Capacity 29 ft.-95 ft. (8.8-29 m) 4 section, full power synchronized boom 26 ft.- ft. (7.9-13.7 m) offsettable telescopic swingaway extension Optional 8,4 lb. (3837 kg)

More information

30105F-D TECHNICAL SPECIFICATIONS 30105F-D SIDE VIEW DIAGRAM. Maximum Vertical Reach. Powered Boom Sections 4 Overall Height

30105F-D TECHNICAL SPECIFICATIONS 30105F-D SIDE VIEW DIAGRAM. Maximum Vertical Reach. Powered Boom Sections 4 Overall Height 30105F-D 30105F-D SIDE VIEW DIAGRAM Maximum Vertical Reach 162'/49 m Working Area 180 Degrees Standard (360 Optional) Lifting Capacity 60,000 lbs/27 216 kg Boom Length 105 /32 m Crane Weight (Standard)

More information

National Crane Series NBT30H

National Crane Series NBT30H National Crane Series NBT30H Product Guide Features 27,2 t (30 USt) rating 33,52 m (110 ft) four-section boom All new design Multi-position Easy Reach control panel Graphical LMI Features National Crane

More information

24,000 lb. ( kg) counterweight with hydraulic removal system. Cummins ISM 450, six cylinder after cooled 450 hp (336 kw)

24,000 lb. ( kg) counterweight with hydraulic removal system. Cummins ISM 450, six cylinder after cooled 450 hp (336 kw) product guide features 41-128 ft. (12.6-39 m) 4 section full power Mega Form boom 33-56 ft. (10-17 m) manual offset bi-fold swingaway 2 x 20 ft. intermediate lattice inserts 24,000 lb. (10 886 kg) counterweight

More information

NATIONAL MODEL 990A - 26 TON CAPACITY

NATIONAL MODEL 990A - 26 TON CAPACITY LIFTING CHARTS - Boom Trucks NATIONAL MODEL 99A - 26 TON CAPACITY Load Chart Rating: Series 99A (27.4 m) Boom with 44 ft. (13.4 m) Jib 2ND JIB 44FT 1ST JIB 25FT LENGTH IN FEET 9 54 27-1 2 8 7 6 A B C D

More information

26105F TECHNICAL SPECIFICATIONS 26105F SIDE VIEW DIAGRAM. Maximum Vertical Reach. Powered Boom Sections 4 Overall Height

26105F TECHNICAL SPECIFICATIONS 26105F SIDE VIEW DIAGRAM. Maximum Vertical Reach. Powered Boom Sections 4 Overall Height 26105F 26105F SIDE VIEW DIAGRAM Maximum Vertical Reach 162'/49,4 m Working Area 180 Degrees Standard (360 Optional) Lifting Capacity 52,000 lbs/23 587 kg Boom Length 105 /32 m Crane Weight (Dry) 26,040

More information

Series 400B. product guide. contents. features. 56' Three-section boom. Features Ton rating. Internal anti-two-block. Mounting Configurations 3

Series 400B. product guide. contents. features. 56' Three-section boom. Features Ton rating. Internal anti-two-block. Mounting Configurations 3 Series 4B product guide features 56' Three-section boom 1 Ton rating Internal anti-two-block Self-lubricating Easy Glide wear pads contents Features 2 Mounting Configurations 3 Specifications 4 Capacities:

More information

Grove TMS700E. Product Guide. Features. 50 t or 55 t (50 USt or 60 USt) capacity

Grove TMS700E. Product Guide. Features. 50 t or 55 t (50 USt or 60 USt) capacity Grove TMS700E Product Guide Features 50 t or 55 t (50 USt or 60 USt) capacity 11 m 33,5 m (36 ft 1 ft) four-section, full power sequenced synchronized boom,1 m 17 m (33 ft 56 ft) offsettable bi-fold lattice

More information

1560F TECHNICAL SPECIFICATIONS 1560F SIDE VIEW DIAGRAM. Maximum Vertical Reach. Powered Boom Sections 3 Overall Height

1560F TECHNICAL SPECIFICATIONS 1560F SIDE VIEW DIAGRAM. Maximum Vertical Reach. Powered Boom Sections 3 Overall Height 1560F 1560F SIDE VIEW DIAGRAM Maximum Vertical Reach 90'/27,4 m Working Area 180 Degrees Standard (360 Optional) Lifting Capacity 30,000 lbs/13 608 kg Boom Length 60 /18,3 m Crane Weight (Dry) 14,825 lbs/6725

More information

UPTime is the Manitex commitment to complete support of thousands of units working every day.

UPTime is the Manitex commitment to complete support of thousands of units working every day. UPTime is the Manitex commitment to complete support of thousands of units working every day. MANITEX 3000 South Austin Avenue Georgetown, Texas 78626 1-877-314-3390 www.manitex.com MTX CM50 1 PC-EN-V1-1113

More information

RT535E. product guide. contents. features 35 ton (35 mt) capacity. Rough Terrain Hydraulic Crane. Features 2. Specifications 3.

RT535E. product guide. contents. features 35 ton (35 mt) capacity. Rough Terrain Hydraulic Crane. Features 2. Specifications 3. product guide contents Features 2 features 35 ton (35 mt) capacity 32-102 ft. (9.8-31.0 m) 4-section full power boom 26-45 ft. (7.6-13.7 m) offsettable telescopic swingaway extension Dual-Axis electric

More information

Series 900A. product guide. contents. features. 103' Four-Section Boom. Features Ton Rating. Self-lubricating Easy Glide Wear Pads

Series 900A. product guide. contents. features. 103' Four-Section Boom. Features Ton Rating. Self-lubricating Easy Glide Wear Pads Series 9A product guide features 13' Four-Section Boom 26 Ton Rating Self-lubricating Easy Glide Wear Pads Internal Anti-two-block contents Features 2 Mounting Configurations 3 Specifications 4 Capacities:

More information

CM170 TELESCOPIC CRANE CONTENTS ///////////////////////////////////////////////////////////////////////////////////////// Crane Features...4 Boom Diagram...5 Load Chart: Main Boom & Jib...6 LMI Codes...7

More information

rough Terrain crane 60 tons

rough Terrain crane 60 tons rough Terrain crane 60 tons grove rt700e BOOM LENGTHS: 36 to 110 ft JIB LENGTHS: 33 to 56 ft JIB OFFSETS: 0-25 - 45 NOTES: Specifications Superstructure Boom 11 m - 33,5 m (36 ft - 110 ft) four-section,

More information

TMS900E. product guide. contents. features 90 ton (80 mton) capacity. Truck Crane ft ( m) 5 section full power boom

TMS900E. product guide. contents. features 90 ton (80 mton) capacity. Truck Crane ft ( m) 5 section full power boom features 90 ton (80 mton) capacity 37-142 ft (11.2-43.2 m) 5 section full power boom Patented TWIN-LOCK boom pinning system 33-56 ft (10-17m) bifold lattice swingaway extension Optional 33-56 ft (10-17

More information

CONTENTS CM300.1 SERIES TELESCOPIC CRANE

CONTENTS CM300.1 SERIES TELESCOPIC CRANE CM300.1 SERIES TELESCOPIC CRANE CONTENTS ///////////////////////////////////////////////////////////////////////////////////////// Crane Features... 4 3051T Chassis... 5 30100C Chassis... 6 Outrigger Extension...

More information

Tire Size 26.5 x 25 5' 5-1/2" (1661) 12' 2-1/4" (3715)

Tire Size 26.5 x 25 5' 5-1/2 (1661) 12' 2-1/4 (3715) Dimensions 11' 13' 4" (64) TAILSWING 9' " (2997) OVER FENDERS 22' (66) FULL EXT 15' 9" (4801) MID EXT 9' 3-1/2" (2832) RET 9' 9-1/2" (2985) O/R A B C D E F G H 23.5 x 25 5' 4-1/4" (1631) 11' 11-1/2" (36)

More information

KEY. Hook block. Operator aids. Distance from hook to head sheave pin. Cab. Hook and ball. Heating / Air conditioning. Hydraulics.

KEY. Hook block. Operator aids. Distance from hook to head sheave pin. Cab. Hook and ball. Heating / Air conditioning. Hydraulics. KEY /////////////////////////////////////////////////////////////////////////////////////////////////////////////// Operator aids Hook block Cab Distance from hook to head sheave pin Heating / Air conditioning

More information

RT530E. product guide. contents. features 30 ton (30 mt) capacity. Rough Terrain Hydraulic Crane. Features 2. Specifications 3.

RT530E. product guide. contents. features 30 ton (30 mt) capacity. Rough Terrain Hydraulic Crane. Features 2. Specifications 3. RT5E product guide contents Features 2 features ton ( mt) capacity 29-95 ft. (8.8-29 m) 4-section full power boom 26- ft. (7.9-13.7 m) telescopic swingaway extension Max main boom tip height of 2.5 ft.

More information

National Crane Series NBT15

National Crane Series NBT15 National Crane Series NBT15 Product Guide Features 13,4 t (15 USt) rating 18,3 m (60 ft) three-section boom Self-lubricating Easy Glide wear pads Internal anti-two block Load sense hydraulics Radio remote

More information

Courtesy of Crane.Market

Courtesy of Crane.Market CM19 TELESCOPIC CRANE PRELIMINARY CONTENTS / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / Crane Features...4 Boom Diagram...5 Load

More information

PRELIMINARY CONTENTS CM190 TELESCOPIC CRANE

PRELIMINARY CONTENTS CM190 TELESCOPIC CRANE CM190 TELESCOPIC CRANE PRELIMINARY CONTENTS /////////////////////////////////////////////////////////// Crane Features...4 Boom Diagram...5 Load Chart: Main Boom & Jib...6 LMI Codes...7 Reeving Diagram...7

More information

RT540E. product guide. contents. features. Rough Terrain Hydraulic Crane. Features 2. Specifications 3. Dimensions ton (35 mt) capacity

RT540E. product guide. contents. features. Rough Terrain Hydraulic Crane. Features 2. Specifications 3. Dimensions ton (35 mt) capacity RT5E product guide contents Features 2 features ton ( mt) capacity 32 ft. - 2 ft. (9.8 m -31.0 m) 4-section, full power boom 26 ft. - ft. (7.9 m - 13.7 m) offsettable telescopic swing-away extension Full

More information

Courtesy of Crane.Market

Courtesy of Crane.Market 1039F 1039F SIDE VIEW DIAGRAM Maximum Vertical Reach 49'/15 m Powered Boom Sections Working Area 180 Degrees Standard (360 Optional) Overall Height Lifting Capacity Operator Controls 20,000 lbs/9,072 kg

More information

CONTENTS TC500 SERIES TELESCOPIC CRANE

CONTENTS TC500 SERIES TELESCOPIC CRANE TC500 SERIES TELESCOPIC CRANE CONTENTS /////////////////////////////////////////////////////////////////////////////////////////////////////////////// Crane Features...4 5096S Chassis Data - S Models...

More information

Series 400B. product guide. contents. features. 56' Three-Section Boom. Features Ton Rating. Internal Anti-two-block. Mounting Configurations 3

Series 400B. product guide. contents. features. 56' Three-Section Boom. Features Ton Rating. Internal Anti-two-block. Mounting Configurations 3 Series 4B product guide features 56' Three-Section Boom 1 Ton Rating Internal Anti-two-block Self-lubricating Easy Glide Wear Pads contents Features 2 Mounting Configurations 3 Specifications 4 Capacities:

More information

GMK5150 Product Guide

GMK5150 Product Guide GMK5150 Product Guide ASME B30.5 Imperial 85% Features 150 t (175 USt) capacity 50,8 m (167 ft) five-section boom 11,2 m (36 ft) / 17,8 m (58 ft) bi-fold swingaway Two 8 m (26 ft) boom extensions and one

More information

TMS900E. product guide. contents. features 90 ton (80 mton) capacity. Truck Crane ft ( m) 5 section full power boom

TMS900E. product guide. contents. features 90 ton (80 mton) capacity. Truck Crane ft ( m) 5 section full power boom features 90 ton (80 mton) capacity 37-142 ft (11.2-43.2 m) 5 section full power boom Patented TWIN-LOCK boom pinning system 33-56 ft (10-17m) bifold lattice swingaway extension Optional 33-56 ft (10-17

More information

Working Range GROVE MODEL TM TON CAPACITY. LIFTING CHARTS - Hydraulic Truck Cranes 9'-7"

Working Range GROVE MODEL TM TON CAPACITY. LIFTING CHARTS - Hydraulic Truck Cranes 9'-7 LIFTING CHARTS - Hydraulic Truck Cranes GROVE MODEL - TON CAPACITY Working Range 42-1 ft. (12.8-39.6 m) 33-58 ft. (10.0-17.7 m) 3 FEET 210 200 1 58 48 1 1 33 1 1 1 1 1 115 85 20 10 0 20 10 0 1 1 1 1 1

More information

To learn more about this model, call or visit giuffre.com today! GIUFFRE.COM

To learn more about this model, call or visit giuffre.com today! GIUFFRE.COM TC300 SERIES TELESCOPIC CRANE 2 CONTENTS //////////////////////////////////////////////////////////////////////////////////////// Crane Features...4 Chassis Data... 5 Outrigger Extension... 6 Sub Frame...6

More information

RT875E. product guide. contents

RT875E. product guide. contents product guide contents Features 2 Specifications 3 Dimensions 5 Working Range 6 Bifold Load Charts 7 features 75 ton (68 mt) capacity 41 ft-128 ft (12.6 m-39.0 m) 4 section, full power boom 33 ft-56 ft

More information

Series 600E. product guide. contents. features. All New Design. Features 2. 90' Four-Section Boom. 20 Ton Rating. Mounting Configurations 3

Series 600E. product guide. contents. features. All New Design. Features 2. 90' Four-Section Boom. 20 Ton Rating. Mounting Configurations 3 Series 6E product guide features All New Design 9' Four-Section Boom 2 Ton Rating Self-lubricating Easy Glide Wear Pads Internal Anti-two-block Auxiliary Stabilizers Variable Displacement Hydraulic System

More information

RT875E. product guide. contents

RT875E. product guide. contents product guide contents Features 2 Specifications 3 Dimensions 5 Working Range 6 Bifold Load Charts 7 features 75 ton (68 mt) capacity 41 ft-128 ft (12.6 m-39.0 m) 4 section, full power boom 33 ft-56 ft

More information

To learn more about this model, call or visit giuffre.com today! GIUFFRE.COM

To learn more about this model, call or visit giuffre.com today! GIUFFRE.COM 2 TC400 SERIES TELESCOPIC CRANE CONTENTS ///////////////////////////////////////////////////////////////////////////////////////// Crane Features...4 TC400 Chassis Data - S Models... 5 TC400 Chassis Data

More information

CONTENTS TC400 SERIES TELESCOPIC CRANE

CONTENTS TC400 SERIES TELESCOPIC CRANE TC400 SERIES TELESCOPIC CRANE CONTENTS ///////////////////////////////////////////////////////////////////////////////////////// Crane Features...4 TC400 Chassis Data - S Models... 5 TC400 Chassis Data

More information

GRT8100 Product Guide

GRT8100 Product Guide GRT8100 Product Guide ASME B30.5 Imperial 85% Features 90 t (100 USt) capacity 12 m 47 m (39.2 ft 154.3 ft) five-section full-power boom 10 m 17 m (33 ft 56 ft) manual offsettable bi-fold lattice swingaway

More information

CONTENTS TC700 SERIES TELESCOPIC CRANE

CONTENTS TC700 SERIES TELESCOPIC CRANE TC700 SERIES TELESCOPIC CRANE CONTENTS //////////////////////////////////////////////////////////////////// Crane Features... 4 Range Diagram... 5 Load Chart: Main Boom... 6 Load Chart: Main Boom... 7

More information

CONTENTS TC500 SERIES TELESCOPIC CRANE

CONTENTS TC500 SERIES TELESCOPIC CRANE TC500 SERIES TELESCOPIC CRANE CONTENTS /////////////////////////////////////////////////////////////////////////////////////////////////////////////// Crane Features...4 5096S Chassis Data - S Models...

More information

RT875E. product guide. contents

RT875E. product guide. contents product guide contents Features 2 Specifications 3 Dimensions 5 Working Range 6 Bifold Load Charts 7 features 75 ton (68 mt) capacity 41 ft-128 ft (12.6 m-39.0 m) 4 section, full power boom 33 ft-56 ft

More information

features also available.

features also available. features 2 The boom on the is a 29-95 ft. (8.8-29 m) four-section full power boom with a maximum tip height of 2.5 ft. (31.2 m). This synchronized boom uses a single lever joystick control to extend boom

More information

TMS x 4 & 6 x 6

TMS x 4 & 6 x 6 TMS5 6 x 4 & 6 x 6 Dimensions 8' (2438) TAILSWING 11' 1" (3383) 7' 8" (2337) RET 13' 9-3/4" (4210) MID EXT ' (96) EXT Note: ( ) Reference dimensions in mm 16-3/4" (425) 43' 4" (13 8) OVERALL 10' 10" (32)

More information

Series 500E. product guide. contents. features. All New Design. Features 2. 71' Three-Section Boom. 18 Ton Rating. Mounting Configurations 3

Series 500E. product guide. contents. features. All New Design. Features 2. 71' Three-Section Boom. 18 Ton Rating. Mounting Configurations 3 Series product guide features All New Design 71' Three-Section Boom 18 Ton Rating Self-lubricating Easy Glide Wear Pads Internal Anti-two-block Auxiliary Stabilizers Variable Displacement Hydraulic System

More information

GMK Product Guide

GMK Product Guide GMK5180-1 Product Guide ANSI B30.5 Imperial 85% Features 180 t (210 USt) capacity 64 m (210 ft) six-section main boom 11 m (59.1 ft) swingaway with jib and/or boom inserts. Maximum 34 m (111.6 ft) length

More information

WORKING RANGE DIAGRAM

WORKING RANGE DIAGRAM Working Range Bi-fold Swingaway 36-110 ft. (11-33.5 m) 33-56 ft. (10.1-17.1 m) 12,1 lbs. (5511 kg) 100% 360 WORKING RANGE DIAGRAM 180 170 160 1 (BOOM DEFLECTION NOT SHOWN) 40 D6-829-101026 0 25 56' 33'

More information

E145 TECHNICAL SPECIFICATIONS E145 SIDE VIEW DIAGRAM. Maximum Working Height. Overall Height Main Boom Length. 145 /44,2 m.

E145 TECHNICAL SPECIFICATIONS E145 SIDE VIEW DIAGRAM. Maximum Working Height. Overall Height Main Boom Length. 145 /44,2 m. E145 E145 SIDE VIEW DIAGRAM Maximum Working Height 145 /44,2 m Overall Height Main Boom Length 125 /38,1 m Operator Controls Ride-Around Seated Outrigger Type Front Out-Down EZ-CRIB Powered Boom Sections

More information

RT530E-2 Product Guide

RT530E-2 Product Guide RT530E-2 Product Guide ASME B30.5 Imperial 85% Features 30 t (30 USt) capacity 8,8 m 29 m (29 ft 95 ft) four-section fullpower boom 7,9 m 13,7 m (26 ft 45 ft) offsettable telescopic swingaway extension

More information

TMS900E. product guide. contents. features 90 ton (80 mton) capacity. Truck Crane ft ( m) 5 section full power boom

TMS900E. product guide. contents. features 90 ton (80 mton) capacity. Truck Crane ft ( m) 5 section full power boom features 90 ton (80 mton) capacity 37-142 ft (11.2-43.2 m) 5 section full power boom Patented TWIN-LOCK boom pinning system 33-56 ft (10-17m) bifold lattice swingaway extension Optional 33-56 ft (10-17

More information

GMK5250L Product Guide ASME B30.5 Imperial 85%

GMK5250L Product Guide ASME B30.5 Imperial 85% GMK5250L Product Guide ASME B30.5 Imperial 85% Features 250 t (300 USt) capacity 70 m (230 ft) seven-section main boom 21 m (69 ft) swingaway with jib and/or boom inserts. Maximum 37 m (121 ft) length

More information

TADANO MODEL TM TON CAPACITY

TADANO MODEL TM TON CAPACITY LIFTING CHARTS - Trucks TADANO MODEL TM-35100-35 TON CAPACITY WORKING RANGE 25 45 5 160ʼ 150ʼ 140ʼ 79.5 7 6 100ft + 28.2ʼ jib 100ft + 50.0ʼ jib 5 45 4 35 3 86.2ft 100ft 130ʼ 120ʼ 110ʼ 100ʼ 90ʼ 80ʼ 70ʼ

More information

TMS700E. product guide. contents. features 50 or 60 ton (50 or 55 mt) Capacity. Truck Mounted Hydraulic Crane. Features 2

TMS700E. product guide. contents. features 50 or 60 ton (50 or 55 mt) Capacity. Truck Mounted Hydraulic Crane. Features 2 TMS0E product guide features or ton ( or mt) Capacity 36 ft.-1 ft. (11-33.5 m) 4 section, full power sequenced synchronized boom 33 ft.-56 ft. (.1-17 m) offsettable bi-fold lattice swingaway extension

More information

National Crane 400B Series

National Crane 400B Series National Crane 4B Series Product Guide Features 17,1 m (56 ft) three-section boom 9,1 t (1 USt) rating Self-lubricating Easy Glide wear pads Internal anti-two block Features National Crane Series 4B 9,7

More information

TMS Preliminary Product Guide

TMS Preliminary Product Guide TMS9000-2 Preliminary Product Guide ASME B30.5 Imperial 85% Features 100 t (115 USt) 11,2 m - 51,6 m (36 ft -169 ft) six-section greaseless MEGAFORM boom TWIN-LOCK boom pinning system Several 10,5 m -

More information

CROSSOVER T capacity class Boom truck crane Datasheet imperial

CROSSOVER T capacity class Boom truck crane Datasheet imperial CROSSOVER 00 T capacity class Boom truck crane Datasheet imperial CROSSOVER 00 Features tons @ 10 capacity at rated distance from center of rotation 110 maximum boom length 118 maximum tip height 32/57

More information

RT530E-2. product guide. contents. features. Rough Terrain Hydraulic Crane. Features 2. Specifications ton (27 mt) capacity.

RT530E-2. product guide. contents. features. Rough Terrain Hydraulic Crane. Features 2. Specifications ton (27 mt) capacity. RT5E-2 product guide contents Features 2 features ton (27 mt) capacity 29 ft. - 95 ft. (8.8 m -29.0 m) 4-section full power boom 26 ft. - ft. (7.9 m - 13.7 m) offsettable telescopic swing-away extension

More information

CROSSOVER 4500L. 45T capacity class Boom Truck Crane Datasheet imperial. View thousands of Crane Specifications on FreeCraneSpecs.com.

CROSSOVER 4500L. 45T capacity class Boom Truck Crane Datasheet imperial. View thousands of Crane Specifications on FreeCraneSpecs.com. 45T capacity class Boom Truck Crane Datasheet imperial Features 45 ton rated capacity @ 9 ft from center of rotation 129 ft maximum boom length 136 ft maximum tip height 32/49 ft optional jib 183 ft maximum

More information

National Crane 1800 Series

National Crane 1800 Series National Crane 1800 Series Product Guide Features 36,29 t (40 USt) rating 43,28 m (142 ft) five-section boom (80 ft) Self-lubricating Easy Glide wear pads Tailswing counterweight Features Outriggers Outrigger

More information

National Crane Series 800D Product Guide ASME B30.5 Imperial 85%

National Crane Series 800D Product Guide ASME B30.5 Imperial 85% National Crane Series 8D Product Guide ASME B3.5 Imperial 85% Features 2,87 t (23 USt) rating 3,48 m (1 ft) four-section boom Self-lubricating Easy Glide wear pads Internal Anti-Two Block Features National

More information

RT700E. product guide. contents

RT700E. product guide. contents product guide contents Features 2 Specifications 3 Dimensions 5 Working Range 6 features -60 ton (-55 mt) capacity 36 ft-110 ft (11 m-33.5 m) 4 section, full power boom 33 ft (10.1 m) offsettable lattice

More information

CROSSOVER Datasheet imperial. Boom Truck Crane 60T capacity class. Features

CROSSOVER Datasheet imperial. Boom Truck Crane 60T capacity class. Features Boom Truck Crane T capacity class Datasheet imperial Features tons @ 10 capacity at rated distance from center of rotation 110 maximum boom length 115 maximum tip height 32/57 optional jib 1 maximum sheave

More information

CONTENTS TM200 TELESCOPIC CRANE

CONTENTS TM200 TELESCOPIC CRANE TM200 TELESCOPIC CRANE CONTENTS ///////////////////////////////////////////////////////////////////////////////////////// Crane Features...4 Boom Diagram...5 Chart: Main Boom & Jib...6 LMI Codes...7 Reeving

More information

GRT655/GRT655L Product guide

GRT655/GRT655L Product guide GRT655/GRT655L Product guide ASME B30.5 Imperial 85% Features 51 t (55 Ust) capacity GRT655: 10,6 m - 34,8 m (34.9 ft - 114.3 ft) four-section full-power boom GRT655L: 10,8 m - 43,0 m (35.3 ft - 141.2

More information

TMS Product Guide

TMS Product Guide TMS9000-2 Product Guide ASME B30.5 Imperial 85% Features 100 t (115 USt) 11,2 m - 51,6 m (36 ft -169 ft) six-section greaseless MEGAFORM boom TWIN-LOCK boom pinning system Several 10,5 m - 17,6 m (34.5

More information

190 /58 m. 202 /62 m. Ride-Around Seated Main Boom Length

190 /58 m. 202 /62 m. Ride-Around Seated Main Boom Length E190 E190 SIDE VIEW DIAGRAM Working Height Without Jib 190 /58 m Overall Height Working Height With Isolating Jib 202 /62 m Operator Controls Ride-Around Seated Main Boom Length 170 /52 m Outrigger Type

More information

CONTENTS TC500 SERIES TELESCOPIC CRANE

CONTENTS TC500 SERIES TELESCOPIC CRANE TC500 SERIES TELESCOPIC CRANE CONTENTS /////////////////////////////////////////////////////////////////////////////////////////////////////////////// Crane Features...4 5096S Chassis Data - S Models...

More information

Grove GHC130. Product Guide. Features. ASME B30.5 Metric 75% and Imperial 75%

Grove GHC130. Product Guide. Features. ASME B30.5 Metric 75% and Imperial 75% Grove GHC130 Product Guide ASME B30.5 Metric 75% and Imperial 75% Features 120 t (132 USt) capacity 12,6 m 40,2 m (41 ft 4 in 131 ft 11 in) four-section full power boom 15 m (49 ft 3 in) offsettable boom

More information

GMK5150L Product Guide

GMK5150L Product Guide GMK5150L Product Guide ASME B30.5 Imperial 85% Features 150 t (175 USt) capacity 60 m (197 ft) six-section boom 11,2 m (36 ft) / 17,8 m (58 ft) bi-fold swingaway 8 m (26 ft) boom and 8 m (26 ft) jib extensions

More information

GCD15 Product Guide. Features. ASME B30.5 Imperial 85%, Metric 85%

GCD15 Product Guide. Features. ASME B30.5 Imperial 85%, Metric 85% GCD15 Product Guide ASME B30.5 Imperial 85%, Metric 85% Features 13,6 t (15 USt) capacity 12,5 m (41 ft) three-section full-power boom 8,1 t (9 USt ) deck carrying ability Load sensing hydraulic piston

More information

To learn more about this model, call or visit giuffre.com today! GIUFFRE.COM

To learn more about this model, call or visit giuffre.com today! GIUFFRE.COM TC500 SERIES TELESCOPIC CRANE CONTENTS 2 /////////////////////////////////////////////////////////////////////////////////////////////////////////////// Crane Features...4 5096S Chassis Data - S Models...

More information

SCD15 Product Guide. Features. ASME B30.5 Imperial 85%

SCD15 Product Guide. Features. ASME B30.5 Imperial 85% SCD15 Product Guide ASME B30.5 Imperial 5% Features 13,6 t (15 USt) capacity 12,5 m (41 ft) three-section full-power boom,1 t (9 USt ) deck carrying ability Load sensing hydraulic piston pump Mechanical

More information

43' (13.07) 18' 4" (5.59 ) 18' 6" (5.64) Turning Radius: TMS870-45' 1" (13.7 m) TTS870-29' 8" (9.04 m) (8 wheel)

43' (13.07) 18' 4 (5.59 ) 18' 6 (5.64) Turning Radius: TMS870-45' 1 (13.7 m) TTS870-29' 8 (9.04 m) (8 wheel) Dimensions 14' 1/2" (4.28) TAILSWING 7' 7" (2.77) O/R RET. 8' 6" (2.59) 15' 5" (5.64) O/R PART. EXTENDED 24' (7.31) ' 6" (4.5) RETRACTED 137' 9" (1653.62) EXTENDED 43' (13.07) 11' 8-1/4" (3.56) 1' 8" (0.53)

More information

National Crane Series 1300A

National Crane Series 1300A National Crane Series 1300A Product Guide ASME B30.5 Imperial 85% Features 27,2 t (30 USt) rating 33,52 m (110 ft) four-section boom Self-lubricating Easy Glide wear pads Internal anti-two-block Vision

More information

Features. Engine. MegaDrive A mixture of conventional drive at the front and hybrid drive for slow speed. Additional features

Features. Engine. MegaDrive A mixture of conventional drive at the front and hybrid drive for slow speed. Additional features Grove GMK6400 North American Product Guide ASME B30.5 Imperial 85% Features 400 t (450 USt) rating 15,4 m - 60 m (51 ft - 197 ft) five-section boom 25 m - 79 m (82 ft - 259 ft) luffing jib Self-rigging

More information