Table of Contents G-1 STAGING, LIGHTING AND SUPPORT SYSTEMS

Transcription

1 Table of Contents STAGING, LIGHTING AND SUPPORT SYSTEMS Page Description Page # Page Description Page # General Section Table of Contents G-1 TOMCAT Policies G-2 Guidelines for Truss Use G-3 Reading Tables G-4 Calculating s G-5 Corner & Sleeve Blocks G-6 Leveling Tower Supported Grids G-7 Faxable Quote Form G-8 Truss Section Pre-Rigged 26" x 18.5" SHPRT (spigoted) T-1 Related Data T-2 26" x 18.5" SHPRT (plated) T-3 Related Data T-4 26" x 30" DHPRT (spigoted) T-5 Related Data T-6 20" x 30" DHPRT (plated) T-7 Related Data T-8 30" x 30" HDPRT (spigoted) T-9 Related Data T-10 Box Truss 13.7" x 10" Super Beam (spigoted) T-11 Related Data T-12 12" x 12" Light Duty (spigoted) T-13 Related Data T-14 12" x 12" Light Duty (plated) T-15 Related Data T-16 12" x 18" Light Duty (plated) T-17 Related Data T-18 12" x 30" Ballroom (spigoted) T-19 Related Data T " x 20.5" Medium Duty (spigoted) T-21 Related Data T " x 20.5" Medium Duty (plated) T-23 Related Data T-24 30" x 20.5" Heavy Duty (spigoted) T-25 Related Data T-26 30" x 20.5" Heavy Duty (plated) T-27 Related Data T-28 36" x 24" XHDT (spigoted) T-29 Related Data T-30 25" Stacking Truss (spigoted) T-31 Related Data T-32 Triangle Truss 20.5" Fixed Triangle (spigoted) T-33 Related Data T " Fixed Triangle (plated) T-35 Related Data T-36 TTR Compatible Truss T-43 Related Data T " x 20.5" Folding Medium Duty T-45 Related Data T-46 30" x 20.5" Folding Heavy Duty T-47 Related Data T-48 Intelligent Truss 26"x 30" Plated Intelligent Truss T-49 Related Data T-50 Specialized Items 12" Ground Support Systems T-51 16"Ground Support Systems T-52 Spot Chair T-53 Speaker Bumpers/Curved Trusss T-54 Roof System Section PRT Sunshade Roof System Roof System S-1 PRT Sunshade Roof System Roof System S-2 46' x 43' Roof System S-3 Related Information S-4 64' x 40' BFT Roof System S-5 Related Information S-6 KT-7 Roof System S-7 Related Information S-8 45' x 45' Ladder Roof System S-9 Related Information S-10 65' x 45' Ladder Roof System S-11 Related Information S-12 Custom Roof Systems S-13 Custom Roof Systems S-14 Motors & Control Section CM Chain Hoists M-1 Specifications & Item Codes M-2 Power & Control Cabling M-3 8-Way Hoist Controllers M-4 4-Way Hoist Controllers M-5 Controller Accessories & Options M-6 Rigging Section Rigging Examples R-1 Rigging Hardware R-2 Descriptions & Item Codes R-3 Polyester Roundslings R-4 Nylon and Polyester Slings R-5 Steel Slings R-6 Wire Mesh Slings / Tie Downs R-7 Hoist / Utility Cases R-8 Folding Truss 14" Folding Triangle (spigoted) T-37 Related Data T " Folding Triangle (spigoted) T-39 Related Data T-40 26" Folding Triangle (spigoted) T-41 Related Data T-42 Electric Section Par Cans E-1 Lamp Bars E-2 Electrical Connectors E-3 Descriptions & Item Codes E-4 Electric Cables E-5 Descriptions & Item Codes E-6 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) G-1

2 STAGING, LIGHTING AND SUPPORT SYSTEMS TOMCAT Policies CREDIT POLICY: It is the policy of TOMCAT USA, Inc. (herein after referred to as TOMCAT ) that payment be received with the order unless other arrangements have been made, such as cash on delivery. Credit will only be extended to those clients who have successfully completed a credit application, signed purchase agreement, or otherwise established credit with TOMCAT. Down payments may be required from customers (including those with credit approval) for custom products or other situations that require special raw material purchases or engineering. In such cases the ordering of materials and fabrication will not proceed until payment or a letter of credit has been received. SHIPPING POLICY: All shipments are Freight On Board Midland, Texas and shall be in good order upon release to the carrier. All claims for damage or loss in transit must be filed by the consignee against the carrier. All freight should be checked for quantity against bill provided by the carrier. Inspect shipments by removing all packaging and checking the truss for damage to chords, internals or to the end of tubes before signing carrier s receipt. Damage noted on freight bill will enable consignee to file a claim against the carrier. Any transport insurance is the responsibility of the purchaser. TOMCAT will not be held responsible or liable for damage, loss or delay in transit. PRODUCT GUARANTEE: TOMCAT guarantees its products will be free from defects in workmanship and materials at the time of purchase and that providing the purchaser follows the manufacturer s guidelines for use, the product will be guaranteed for a period of one year from the date of shipment to perform according to the published specifications of the product. TOMCAT is not responsible for damage to product in transit, nor in cases where load specifications were exceeded or where guidelines for usage were not followed. Except as expressly stated and warranted herein: (i) TOMCAT disclaims any other warranties, whether express or implied, including any warranty of merchantability or fitness for a specific purpose; (ii) unless project engineer reports are included, TOMCAT has made no affirmations of fact or promise relating to the goods being sold that has become the basis of this bargain, or that has created or amounted to an express warranty that the goods would conform to any such affirmation or promise; (iii) this warranty extends exclusively to the original purchaser of the warranted goods and subsequent purchasers are not covered by this warranty; (iv) this warranty does not apply to a part which the buyer misuses, damages, improperly maintains, repairs, or replaces with a part not of TOMCAT s manufacture; and (v) except for its duty to repair or replace defective parts, TOMCAT shall not be liable for any consequential or incidental damages resulting from a defective part. TOMCAT reserves the right to change materials or design, when, in our opinion, such changes will improve the product. This warranty is performable in Midland County, Texas, and all obligations, rights, and duties of buyer and TOMCAT shall be governed by the laws of the State of Texas. RETURN POLICY: Prior to returning any item purchased from TOMCAT, a customer must first contact TOMCAT to obtain a Returned Goods Authorization number (RGA #). Returned goods without prior authorization will not be accepted. TOMCAT will not generally pay the cost of return freight, and reserves the right to refuse return shipments where the freight has not been prepaid by the returning party. G-2 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

3 STAGING, LIGHTING AND SUPPORT SYSTEMS Guidelines for Truss Usage HANDLING: TOMCAT Truss is engineered to provide many years of dependable service provided that it is handled properly and used within the recommended loading parameters. Do not drag or drop truss as this may damage the ends of the truss or result in other unseen damage. The ends of the tubes need to be maintained as round as possible so that connections will be complete. When transporting, take steps to ensure that nothing rubs against the truss that might cause wear or punctures. When transporting vertically, truss with spigots should be arranged with the male members down; truss with Camlocs should be arranged with the male members up. When stacking truss in transport, secure the truss to prevent bouncing and do not load other items onto the top of the truss that could bounce and cause damage. When loading, unloading, or moving truss do so with enough personnel as to assure that the truss is not dropped or dragged over other truss. This also assures personal safety. Use fork lifts with extreme caution! Place forks only under the bottom cord as placing forks through the truss could damage diagonals. ASSEMBLY & USE: TOMCAT box truss is typically designed with horizontal cross members on two opposing faces with diagonal and vertical members on the other two faces. The intersection of vertical and horizontal members with the continuous chord member is called a panel point. The faces with horizontal cross members make up the top and bottom of the truss, while the faces with diagonals are the sides. (See Figure 1.) data is only valid when the truss is oriented in this fashion. data is only to be considered for indoor use. data takes into consideration the self-weight of the truss and indicates how much additional weight may be safely added. Triangular truss should be oriented with the apex up. Turning it over reduces load capacity significantly. For folding-triangle truss, the apex is the hinged pair of chords. When connecting sections of truss, make sure the diagonals form a continuous pattern. (See Figure 2.) The diagonals on each side of the connection should be opposed, not parallel. Span lengths and load specifications as published by TOMCAT should not be exceeded without first contacting TOMCAT. The balance between members and the even distribution of load across the truss is an important consideration, as unbalanced loads could twist the truss resulting in damage. For optimum weight distribution it is recommended that the truss itself be hung using the lower chords, while additional loads be suspended from the upper chords. All loads should be applied at panel points as described above. Local bending of members may occur if loads are applied at locations other than panel points. All truss connecting parts should be inspected regularly. Camlocs should be inspected for wear and abuse. Female members may become loose or worn while males may become twisted, have elongated holes or missing set screws. Crosspins that show wear or are bent should be replaced immediately. Set screws are used to adjust the compression on the crosspin and should be checked for proper tension on each use. Do not, however, adjust the set screw while the Camloc is mated. If the Camloc is loose when mated, disconnect the Camloc and adjust the set screw. Likewise if it is difficult to lock, the set screw should be loosened until the Camloc will mate securely. Never use undue force in mating Camlocs. When using nuts and bolts, each should be inspected on a regular basis. Use only grade 8 bolts and nuts. Washers should be used on both sides. Nuts and bolts should be replaced periodically as regular use degrades bolt threads. Never over-torque nuts and bolts beyond manufacturers specifications. Prior to lifting a truss, one person should be responsible for checking all truss connections, and the rigging on the truss, assuring that rigging has been done at the panel points. When raising truss, hoists should run simultaneously once the truss is leveled. Always observe the hoists closely when moving truss, and stop every 15-feet to check the level of the grid. This is particularly important if the grid is unevenly loaded. When disassembling truss, do not break any connections until there is no weight on the joints. Figure 1. Figure 2. Side View Top or Bottom View Incorrect Correct 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) G-3

4 STAGING, LIGHTING AND SUPPORT SYSTEMS Reading Tables The following abbreviations are used in the load tables for the truss sections in this manual: UDL -. - #/ft. - mtrs. - Uniformly Distributed imum Deflection Pounds per Linear Foot meters MEDIUM DUTY TRUSS 20.5" x 20.5" SPIGOTED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER lbs. - - ft. - kgs. - Pounds Inches Feet Kilograms For the sake of explanation and clarification we have selected the load table for Spigoted Medium Duty Truss as an example: MAXIMUM ALLOWABLE LOADS THIRD QUARTER No. of 10' Sections Span ft. (mtrs) #/ft. Spigots Only (3) (6.1) (9.1) (12.2) (15.2) (4173) (4082) (3429) (2486) (1746) (4175) (2630) (1715) (1246) (957) (2087) (1972) (1286) (935) (648) (1392) (1315) (858) (623) (465) Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 10'-0" sections. Other Asection lengths are available. (A) The load tables published contain a note describing the length of truss used to determine the allowable load data. Other section lengths are available which make up spans other than those given. It is acceptable to interpolate between the values given for such spans. (B) data is provided for each truss according to its connection type. (C) The uniformly distributed load is permitted only if the load is evenly distributed across the entire span of truss. (D) The center-point load reported is the maximum allowable point load applied at midspan of the truss. (E) The third-point load is the maximum allowable point load applied at each third point along the span of the truss. (F) The quarter-point load is the maximum allowable point load applied at each quarter point along the span of the truss. All point loads shall occur at panel points (the intersection of a chord and a diagonal or a chord and a vertical). The selfweight of the truss has been taken into account in each of the load tables and therefore does not have to be included in the calculation of superimposed live load. The effects of shock loadings and dynamic loadings have not been taken into account in the preparation of the tables. Significant dynamic loads can be induced upon a truss during movement. One such example is when a truss is lifted by a chain motor. Dynamic loads must be resolved to static load equivalents before they can be compared to the allowable load data. The deflections reported are based upon the corresponding maximum allowable load being applied to the truss. Actual deflections may be slightly higher than those reported due to connection tolerances. All load table data is reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc. structural engineers, and apply to truss fabricated after December, B C D E F G-4 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /

5 STAGING, LIGHTING AND SUPPORT SYSTEMS Calculating s A quick rule-of-thumb you might want to remember is: If the total weight you plan to place on the truss (no matter the location of the hanging point or points) is less than half of the total UDL for your span, you will not be overstressing the truss. For example, a 40' span of Medium Duty spigoted truss has a total allowable UDL of 5480 lbs. If you have an irregular pattern of point loads that do not correspond with one of the published load configurations, you can still be sure that you are within allowable load limits if the total weight of all of the point loads is less than half of the total UDL. Using our example, if the point loads on the truss which totaled 2740 lbs. or less you would not be overstressing the truss. Additionally, a truss may be loaded with a combination of point loads and uniformly distributed loads. In this condition, the percentage of point load capacity is equal to the percentage of uniformly distributed load capacity not used. Of course, if you are uncertain whether your specific load configuration is acceptable, you can always call your TOMCAT representative for assistance. It may be necessary to calculate the load each of your chain hoists will be required to lift. To determine those end reactions we would employ the following formulas: Where: R 1 = P 1 b 1 L + P 2 b 2 L + P 3 b 3 L + For example, four sections of 10' Medium Duty Truss are supported at each end with chain hoists. The truss is loaded with two point loads rigged at panel points: L = 480" R 2 = P 1 a 1 L + P 2 a 2 L + P 3 a 3 L + P 1, P 2, P 3, etc. are point loads applied to the truss (typically rigging points); R 1 and R 2 are end reactions of the truss resulting from the application of point loads P 1, P 2, P 3, etc.; a 1, a 2, a 3, etc. are the dimensions from the R 1 end of the truss to P 1, P 2, P 3, etc. respectively; and b 1, b 2, b 3, etc.are the dimensions from the R 2 end of the truss to P 1, P 2, P 3, etc., respectively. a 2 = 280" a 1 = 160" R 1 = end reaction on chain hoist b 1 = 320" b 2 = 200" R 2 = end reaction on chain hoist P 1 = 1200 lbs P 2 = 900 lbs To calculate the load that each chain hoist is supporting, plug the values into the equations given above: R 1 = (P 1 = 1200 lbs) x (b 1 = 320") (L = 480") R 1 = = 1175 lbs. + (P 2 = 900 lbs) x (b 2 = 200") (L = 480") R 2 = (P 1 = 1200 lbs) x (a 1 = 160") (L = 480") + (P 2 = 900 lbs) x (a 2 = 280") (L = 480") R 2 = = 925 lbs. 117 x 4 By adding half of the selfweight of the truss as given in the product code table 2 to each end reaction, the total load to be lifted by the chain hoist is determined; for R1 it is 1409 lbs. and for R2 it is 1159 lbs. By adding the weight of the chain hoists and rigging the total load on the supporting structure can be determined. 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) G-5

6 STAGING, LIGHTING AND SUPPORT SYSTEMS Corner & Sleeve Block Orientation In an effort to make it easier for clients to relate to the construction and orientation of corner and sleeve blocks for TOMCAT truss, we are providing the drawings on this page. The blocks are defined by the orientation of the main chords of the blocks and by the type of the connection. For demonstration purposes we have shown only the 4-way versions of each. All are available in 2, 3, and 4-way versions. Additionally, those truss types that have 5 and 6-way versions available are indicated with an asterisk (*). We have numbered each of the faces of the blocks so that you can easily refer to the faces on which you need connections. In the case of spigot or Camloc connections you can also specify the gender of the connection you need on each particular face. When ordering corner blocks, refer to the appropriate truss page for the item code of the corner or sleeve block, then refer to this page to identify the faces on which you need connections (Side 1, 2, 3, 4, 5, or 6). For sleeve applications, connections are not possible on sides 5 & 6. If you have any questions, don t hesitate to call the TOMCAT sales staff for assistance. Corner Blocks with Horizontal Chords and a Bolt Connection: Single Hung Pre-Rig Double Hung Pre-Rig 12" x 12" Light Duty* 12" x 18" Light Duty Medium Duty* Heavy Duty Corner Blocks with Horizontal Chords and a Spigot Connection: Single Hung Pre-Rig Double Hung Pre-Rig Heavy Duty Pre-Rig Super Beam Medium Duty* Heavy Duty Extra Heavy Duty Sleeve Block with Horizontal Chords and a Bolt Connection: Double Hung Pre-Rig Sleeve Blocks with Horizontal Chords and a Spigot Connection: Double Hung Pre-Rig Heavy Duty Pre-Rig Medium Duty Heavy Duty Extra Heavy Duty Sleeve Blocks with Vertical Chords and a Bolt Connection: Medium Duty Heavy Duty G-6 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

7 STAGING, LIGHTING AND SUPPORT SYSTEMS Leveling Roof & Ground Support Systems In order to properly use ground support systems, the truss must be level during lift and at trim (unless it has been specifically designed for other orientations). Below are some guidelines to be followed in order to properly use ground support systems. The first step when erecting a ground support system is to select a site which has a minimal difference in grade. Sites with large slopes or mounds and depressions should be avoided or leveled prior to erecting the system. Once a level site is selected, the locations of the bases should be determined. A firm foundation is required under each base which will not settle under heavy loading even in the presence of moisture. The user should have an understanding of what loading is going to be present at each tower base as well as the bearing capacity of the surface on which the tower base is supported so that the bearing capacity is not exceeded. Plywood or steel plates or both may be required under the tower bases to provide less concentrated loading to the ground directly under the base screw jacks. Once the base locations are level, the bases can be placed, the tower hinges can be set, the sleeves can be positioned over the tower hinges and the grid can be assembled on the ground. After assembly of the grid, the towers can be assembled on the grid, attached to the hinge and raised into vertical position. Then the grid can be raised to a level just high enough so that the outriggers can be inserted into the base. All screw jacks should be turned so that each pad is making contact with the ground or bearing plate (wood or steel). Additional wood blocks may be needed under the screw jacks so that at this point no more than two inches of the screw jack threads extend below the base or outriggers at this time. After checking that all screw jacks at each tower base are making contact with the ground, the grid can be raised to just above the tower hinge. Now the stabilizers can be attached to the outriggers and to the tower, however, initially leave the clamps loose at the tower. With the use of a long spirit level (3' or longer) against a tower leg, determine which stabilizer is required to push the tower into level. Tighten the clamp of this stabilizer first and check the level. It may be required to tighten two stabilizer clamps at a time in order to level the tower. Once the tower is level, the remaining stabilizer clamps can be tightened. All of the screw jacks should again be checked for contact with the ground after the stabilizers are installed. It may be necessary to adjust the screw jacks on the outriggers but never should they be turned down to an extent that they take weight off of the base. After all adjustments are made to the screw jacks, it is important to never have more than three inches of thread extending below the base or outriggers. The tower should now be perpendicular to a true horizontal plane. You may visually align the tower from a distance using other vertical lines in the background as a reference such as the edge of permanent buildings, poles or towers. Once confident that the towers are vertical, it is time to begin the process of lifting the grid to trim height. The chain motors may run at slightly different speeds (possibly from uneven loading on the grid). Therefore, stop the lift of the grid approximately every 15' and check for level. To check for level, a tape measure can be placed at each lift point of the grid to measure the distance to the ground. If the ground is level, all of the measurements should be the same. If the ground is not level, a level line or laser level should be used to create a true horizontal plane to which the measurements can be made. This process should continue until the grid reaches trim height. After the grid is lifted into level trim height, the installation of guy wires (if required) can proceed. 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) G-7

8 STAGING, LIGHTING AND SUPPORT SYSTEMS Your Name: Company: Address: City: State / Province: Zip / Postal Code: Country: Telephone Number: Facsimile Number: Faxable Quote Form Instructions for Use To receive a quote on products contained in this catalog, fill in the blanks below and fax to TOMCAT. From North America and the Far East, fax to: TOMCAT, USA +1 (915) From Mexico and South America, fax to: TOMCAT de Mexico +52 (3) All other countries fax to: TOMCAT, UK +44 (151) Quantity Item Number Description Unit Price TOMCAT Use Only Total Special Instructions or Questions: Need Quote by: G-8 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

9 STAGING, LIGHTING AND SUPPORT SYSTEMS SINGLE HUNG PRE-RIG TRUSS 26" x 18.5" SPIGOTED * Standard length is 96-1/8" * Available loaded with wired lamp bar of 6 TOMCAT Par 64's * Available in 66-1/8" (4 Par) and 126-1/8" (8 Par) lengths Equipped with steel spigot connections Main chords are 2" OD x 3/16" aluminum Diagonals are 1" OD x 1/8" aluminum Fabricated by certified welders 98.25" (249.55) OD 27.38" (69.54) 26.19" (66.52) 36" (91.44) 33.88" (86.05) 36" (91.44) 33.88" (86.05) 31.25" (79.37) 26" (66.04) 18.5" (46.99) PLAN 2-Way Corner Block 3-Way Corner Block 4-Way Corner Block 96.13" (244.17) 18.5" (46.99) Horiz " (95.04) Horiz " (89.66) Vert (114.09) Vert (100.71) 9.49" (24.1) 8.31" (21.10) 9.25" (23.49) 8.31" (21.10) Horiz. 18.5" (46.99) Vert. 26" (66.04) 27.50" (69.85) 26.56" (67.46) 27.12" (68.88) 26.19" (66.52) 36" (91.44) 33.88" (86.05) ELEVATION END VIEW Center Pivot Horizontal Horizontal Articulating Block Variable Corner PLAN VIEWS Connector Orientation Specified by Customer 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-1

10 ALLOWABLE LOAD DATA SINGLE HUNG PRE-RIG TRUSS 26" x 18.5" SPIGOTED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER No. of Sects. Span ft. (mtrs) #/ft. Spigots Only 1 8 (2.43) (4249) (4251) (2126) (1417) (4.87) (4159) (4162) (2081) (1387) (7.31) (4072) (3485) (2036) (1358) (9.75) (3687) (2079) (1356) (973) (12.19) (2250) (1411) (828) (594) (14.63) (1437) (909) (533) (383) (17.06) (940) (596) (350) (251) 3.73 Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 96" sections. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, SINGLE HUNG PRE-RIG TRUSS 26" x 18.5" SPIGOTED Connections are steel spigots & 3/4" clevis pins 66" SHPRT TRUSS (EMPTY) (66-1/8" pinned length) 96" SHPRT TRUSS (EMPTY) (96-1/8" pinned length) 126" SHPRT TRUSS (EMPTY) (126-1/8" pinned length) SHPRT 2-WAY CORNER BLOCK SHPRT 3-WAY CORNER BLOCK SHPRT 4-WAY CORNER BLOCK SHPRT ARTICULATING BLOCK HORIZONTAL (center pivot) SHPRT ARTICULATING BLOCK VERTICAL (center pivot) SHPRT VARIABLE CORNER HORIZ. (book style with brace) SHPRT VARIABLE CORNER VERT. (book style with brace) 3/4" CLEVIS PIN Item Code TRS S TRS S TRS S TRS 2618-C2S TRS 2618-C3S TRS 2618-C4S TRS 2618-AHS TRS 2618-AVS TRS 2618-VHS TRS 2618-VVS HDW CP-75 Weight 100 (45) 121 (55) 144 (65) 69 (32) 92 (42) 115 (53) 77 (35) 79 (36) 67 (31) 63 (29).4 (.18) SINGLE HUNG PRE-RIG TRUSS (ed) 26" x 18.5" SPIGOTED ed truss includes guide rods, half couplers, silver PAR 64s hard-wired to bar, and multipin connector. Weight Item Code 66-1/8" SHPRT LOADED w/socapex (60" bar with 4 PARs) 66-1/8" SHPRT LOADED w/veam (60" bar with 4 PARs) 96-1/8" SHPRT LOADED w/socapex (90" bar with 6 PARs) 96-1/8" SHPRT LOADED w/veam (90" bar with 6 PARs) 126-1/8" SHPRT loaded w/socapex (120" bar with 8 PARs) 126-1/8" SHPRT loaded w/socapex (120" bar with 8 PARs) ed truss includes lamp bulb weight. TRS SLS TRS SLV TRS SLS TRS SLV TRS SLS TRS SLV 135 (62) 135 (62) 171 (78) 171 (78) 209 (95) 209 (95) MEDIUM R-CLIP HDW RC-MED Empty truss includes guide rods & half couplers for rigging lamp bar. T-2 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

11 STAGING, LIGHTING AND SUPPORT SYSTEMS SINGLE HUNG PRE-RIG TRUSS 26" x 18.5" PLATED * Standard length is 93" * Available loaded with wired lamp bar of 6 TOMCAT Par 64's * Available in 63" (4 Par) and 123" (8 Par) lengths Equipped with single Camlocs or bolts Main chords are 2" OD x 1/8" aluminum Diagonals are 1" OD x 1/8" aluminum Fabricated by certified welders 19.25" (48.89) 19.25" (48.89) 19.25" (48.89) 18.5" (46.99) PLAN 2-Way Corner Block 93" (236.22) 18.5" (46.99) Horiz " (71.55) Vert " (90.60) 31.25" (79.37) 26" (66.04) Horiz. 18.5" (46.99) Vert. 26" (66.04) 18.88" (47.95) 18.88" (47.95) 19.25" (48.89c) 3-Way Corner Block 4-Way Corner Block 6.75" (17.14) 6.75" (17.14) ELEVATION END VIEW Center Pivot Horizontal Articulating Block Horizontal Variable Corner PLAN VIEWS 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-3

12 ALLOWABLE LOAD DATA SINGLE HUNG PRE-RIG TRUSS 26" x 18.5" PLATED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER No. of Sects Span ft. (mtrs) 7'-9" 15'-6" 23'-3" 31'-0" 38'-9" 46'-6" 54'-3" 7'-9" 15'-6" 23'-3" 31'-0" 38'-9" 46'-6" 54'-3" (2.35) (4.72) (7.04) (9.44) (11.80) (14.17) (16.52) (2.35) (4.72) (7.08) (9.44) (11.80) (14.17) (16.52) #/ft (3993) (2552) (1656) (1181) (896) (675) (517) (2603) (1279) (828) (595) (450) (347) (271) (1952) (959) (621) (446) (337) (261) (203) /8" diameter Grade 8 bolts with standard washers through 3/8" gusset plates (3993) (3743) (1997) (3698) (1849) (1387) (2415) (1208) (906) (1758) (880) (660) (1358) (678) (508) (1055) (538) (403) (861) (434) (325) (1301) (640) (414) (298) (225) (174) (135) (1332) (924) (604) (440) (339) (269) (217) Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 93" sections. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, SINGLE HUNG PRE-RIG TRUSS 26" x 18.5" PLATED Connections are single sets of bolts or Camlocs 63" SHPRT TRUSS (EMPTY) 93" SHPRT TRUSS (EMPTY) 123" SHPRT TRUSS (EMPTY) SHPRT 2-WAY CORNER BLOCK SHPRT 3-WAY CORNER BLOCK SHPRT 4-WAY CORNER BLOCK SHPRT ARTICULATING BLOCK HORIZONTAL (center pivot) SHPRT ARTICULATING BLOCK VERTICAL (center pivot) SHPRT VARIABLE CORNER HORIZ. (book style with brace) SHPRT VARIABLE CORNER VERT. (book style with brace) Item Code Bolt TRS B Cam TRS C Bolt TRS B Cam TRS C Bolt TRS B Cam TRS C Bolt TRS 2618-C2B Cam TRS 2618-C2C Bolt TRS 2618-C3B Cam TRS 2618-C3C Bolt TRS 2618-C4B Cam TRS 2618-C4C Bolt TRS 2618-AHB Cam TRS 2618-AHC Bolt TRS 2618-AVB Cam TRS 2618-AVC Bolt TRS 2618-VHB Cam TRS 2618-VHC Bolt TRS 2618-VVB Cam TRS 2618-VVC Weight 73 (33) 90 (41) 109 (50) 30 (13) 35 (16) 39 (18) 60 (27) 60 (27) 47 (21) 43 (20) Empty truss includes guide rods & half couplers for rigging lamp bar. Single Camloc through 3/8" gusset plates SINGLE HUNG PRE-RIG TRUSS (ed) 26" x 18.5" PLATED ed truss includes guide rods, half couplers, silver PAR 64s hard-wired to bar, and multipin connector Weight Item Code 63" SHPRT LOADED w/socapex Bolt TRS BLS (60" bar with 4 PARs) Cam TRS CLS 63" SHPRT LOADED w/veam Bolt TRS BLV (60" bar with 4 PARs) Cam TRS CLV 93" SHPRT LOADED w/socapex Bolt TRS BLS (90" bar with 6 PARs) Cam TRS CLS 93" SHPRT LOADED w/veam Bolt TRS BLV (90" bar with 6 PARs) Cam TRS CLV 123" SHPRT LOADED w/socapex Bolt TRS BLS (120" bar with 8 PARs) Cam TRS CLS 123" SHPRT LOADED w/veam Bolt TRS BLV (120" bar with 8 PARs) Cam TRS CLV ed truss includes lamp bulb weight. 108 (49) 108 (49) 140 (64) 140 (64) 174 (79) 174 (79) T-4 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

13 STAGING, LIGHTING AND SUPPORT SYSTEMS DOUBLE HUNG PRE-RIG TRUSS 26" x 30" SPIGOTED * Standard length is 96-1/8" * Available loaded with 2 wired lamp bars of 6 TOMCAT Par 64's * Available in 66-1/8" (4 Par) and 126-1/8" (8 Par) lengths Equipped with steel spigot connections Main chords are 2" OD x 3/16" aluminum Diagonals are 1" OD x 1/8" aluminum Fabricated by certified welders 97.87" (248.58) OD 39.25" (99.69) 38.06" (96.67) 47.12" (119.68) 45.38" (115.26) 47.12" (119.68) 45.38" (115.26) 96.13" (244.17) 31.25" (79.37) 30" (76.20) PLAN 2-Way Corner Block 30" (76.20) 3-Way Corner Block 4-Way Corner Block 26" (66.04) 38.63" (98.12) 37.69" (95.73) 38.63" (98.12) 37.69" (95.73) 47.12" (119.68) 45.38" (115.26) Sleeve Version Horiz " (123.29) Horiz " (118.87) Vert " (114.09) Vert " (108.71) 9.13" (23.19) 8.31" (21.10) 9.25" (23.49) 8.31" (21.10) Horiz. 30" (76.20) Vert. 26" (66.04) ELEVATION END VIEW Center Pivot Horizontal Horizontal Articulating Block Variable Corner PLAN VIEWS Connector Orientation Specified by Customer 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-5

14 ALLOWABLE LOAD DATA DOUBLE HUNG PRE-RIG TRUSS 26" x 30" SPIGOTED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER No. of Sects Span ft. (mtrs) (2.43) (4.87) (7.31) (9.75) (12.19) (14.63) (17.06) #/ft. DOUBLE HUNG PRE-RIG TRUSS 26" x 30" SPIGOTED Connections are steel spigots & 3/4" clevis pins 66" PRT TRUSS (EMPTY) (66-1/8" pinned length) 96" PRT TRUSS (EMPTY) (96-1/8" pinned length) 126" PRT TRUSS (EMPTY) (126-1/8" pinned length) PRT 2-WAY CORNER BLOCK PRT 3-WAY CORNER BLOCK PRT 4-WAY CORNER BLOCK PRT ARTICULATING BLOCK HORIZONTAL (center pivot) PRT ARTICULATING BLOCK VERTICAL (center pivot) PRT VARIABLE CORNER HORIZ. (book style with brace) PRT VARIABLE CORNER VERT. (book style with brace) PRT 2-WAY SLEEVE FOR 12" TOWER PRT 3-WAY SLEEVE FOR 12" TOWER PRT 4-WAY SLEEVE FOR 12" TOWER 3/4" CLEVIS PIN Item Code TRS S TRS S TRS S TRS 2630-C2S TRS 2630-C3S TRS 2630-C4S TRS 2630-AHS TRS 2630-AVS TRS 2630-VHS TRS 2630-VVS TRS 2630-S2S TRS 2630-S3S TRS 2630-S4S HDW CP (4242) 9136 (4144) 8904 (4039) 8672 (3934) 7400 (3357) 5712 (2591) 4816 (2185) Weight 117 (53) 134 (61) 163 (74) 83 (38) 106 (48) 130 (59) 97 (44) 92 (42) 74 (34) 79 (36) 114 (52) 137 (62) 160 (73) Spigots Only (4243) (4144) (3478) (2071) (2008) (1299) (1250) Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 96" sections. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, (.18) (2121) (2072) (2023) (1553) (1213) (974) (803) DOUBLE HUNG PRE-RIG TRUSS (ed) 26" x 30" SPIGOTED 26" x 30" ed truss includes guide rods, half couplers, silver PAR 64s hard-wired to bars, and multipin connector. Weight Item Code 66-1/8" PRT LOADED w/ SOCAPEX TRS (2-60" bars with 4 PARs) 66-1/8" PRT LOADED w/ VEAM TRS (2-60" bars with 4 PARs) 96-1/8" PRT LOADED w/ SOCAPEX TRS (2-90" bars with 6 PARs) 96-1/8" PRT LOADED w/ VEAM TRS (2-90" bars with 6 PARs) 126-1/8" PRT LOADED w/ SOCAPEX TRS (2-120" bars with 8 PARs) 126-1/8" PRT LOADED w/ VEAM TRS (2-120" bars with 8 PARs) ed truss includes lamp bulb weight (1414) 3045 (1381) 2973 (1349) 2282 (1035) 1981 (899) 1431 (649) 1271 (577) SLS SLV SLS SLV SLS SLV 187 (85) 187 (85) 234 (107) 234 (107) 293 (134) 293 (134) MEDIUM R-CLIP HDW RC-MED Empty truss includes guide rods & half couplers for rigging lamp bar. T-6 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

15 STAGING, LIGHTING AND SUPPORT SYSTEMS DOUBLE HUNG PRE-RIG TRUSS 26" x 30" PLATED * Standard length is 93" * Available loaded with 2 wired lamp bars of 6 TOMCAT Par 64's * Available in 63" (4 Par) and 123" (8 Par) lengths Equipped with single Camlocs or bolts Available with double Camlocs Main chords are 2" OD x 1/8" aluminum Diagonals are 1" OD x 1/8" aluminum Fabricated by certified welders 30.75" (78.10) 30.75" (78.10) 30.75" (78.10) 93" (236.22) 31.25" (79.37) 26" (66.04) 30" (76.20) 30.38" (77.16) 30.75" (78.10) 30.75" (78.10) 2-Way Corner Block 3-Way Corner Block 4-Way Corner Block PLAN 30" (76.20) Horiz " (100.76) Vert " (90.66) Sleeve Version 6.75" (17.14) 6.75" (17.14) Horiz. 30" (76.20) Vert. 26" (66.04) ELEVATION END VIEW Center Pivot Horizontal Articulating Block Horizontal Variable Corner PLAN VIEWS 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-7

16 ALLOWABLE LOAD DATA DOUBLE HUNG PRE-RIG TRUSS 26" x 30" PLATED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER No. of Sects Span ft. (mtrs) 7'-9" 15'-6" 23'-3" 31'-0" 38'-9" 46'-6" 54'-3" 7'-9" 15'-6" 23'-3" 31'-0" 38'-9" 46'-6" 54'-3" #/ft (3990) (2552) (1645) (1167) (879) (675) (517) (3990) (3958) (2710) (1969) (1511) (1202) (959) (2601) (1276) (823) (589) (442) (338) (259) (3992) (2078) (1358) (990) (763) (606) (489) Two Camlocs through gusset plates DOUBLE HUNG PRE-RIG TRUSS 26" x 30" PLATED End plates equipped for double sets of bolts or Camlocs, supplied with one set only Product Description Item Code Weight 63" PRT TRUSS (EMPTY) 7'-9" 15'-6" 23'-3" 31'-0" 38'-9" 46'-6" 54'-3" (2.43) (4.72) (7.08) (9.44) (11.80) (14.17) (16.52) (2.43) (4.72) (7.08) (9.44) (11.88) (14.17) (16.52) (2.43) (4.72) (7.08) (9.44) (11.88) (14.17) (16.52) Bolt TRS B 90 (41) Cam TRS C Single Camloc through 3/8" gusset plates Item Code Weight PRT ARTICULATING Bolt TRS 2630-AHB 77 (35) BLOCK HORIZ. (center pivot) CamTRS 2630-AHC (1951) (957) (618) (442) (331) (254) (195) (1996) (1559) (1019) (743) (572) (454) (367) /8" diameter Grade 8 bolts with standard washers through 3/8" gusset plates (3990) (3691) (2405) (1744) (1336) (1055) (836) (3741) (1846) (1203) (874) (670) (528) (422) (1996) (1384) (903) (655) (502) (396) (317) (1300) (638) (412) (294) (221) (169) (130) (1330) (1039) (679) (495) (381) (303) (244) DOUBLE HUNG PRE-RIG TRUSS (ed) 26" x 30" PLATED ed truss includes guide rods, half couplers, silver PAR 64s hard-wired to bars, and multipin connector 63" PRT LOADED w/socapex (2-60" bars with 4 PARs) Item Code (1330) (923) (602) (437) (335) (264) (211) Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 93" sections. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, Bolt TRS BLS Cam TRS CLS Weight 160 (72) 93" PRT TRUSS (EMPTY) Bolt TRS B 109 (49) Cam TRS C PRT ARTICULATING BLOCK VERT. (center pivot) Bolt TRS 2630-AVB CamTRS 2630-AVC 72 (33) 63" PRT LOADED w/veam (2-60" bars with 4 PARs) Bolt TRS BLV Cam TRS CLV 160 (72) 123" PRT TRUSS (EMPTY) Bolt TRS B 131 (60) Cam TRS C PRT VARIABLE CORNER Bolt TRS 2630-VHB HORIZ. (book style w/brace) CamTRS 2630-VHC 56 (25) 93" PRT LOADED w/socapex (2-90" bars with 6 PARs) Bolt TRS BLS Cam TRS CLS 209 (95) PRT 2-WAY CORNER BLOCK Bolt TRS 2630-C2B Cam TRS 2630-C2C 40 (18) PRT VARIABLE CORNER VERT. (book style w/brace) Bolt TRS 2630-VVB CamTRS 2630-VVC 59 (27) 93" PRT LOADED w/veam (2-90" bars with 6 PARs) Bolt TRS BLV Cam TRS CLV 209 (95) PRT 3-WAY CORNER BLOCK Bolt TRS 2630-C3B Cam TRS 2630-C3C 46 (21) PRT 2-WAY SLEEVE FOR 12" TOWER Bolt TRS 2630-S2B CamTRS 2630-S2C 73 (33) 123" PRT LOADED w/socapex (2-120" bars with 8 PARs) Bolt TRS BLS Cam TRS CLS 261 (119) PRT 4-WAY CORNER BLOCK Bolt TRS 2630-C4B Cam TRS 2630-C4C 51 (23) PRT 3-WAY SLEEVE FOR 12" TOWER Bolt TRS 2630-S3B CamTRS 2630-S3C 79 (36) 123" PRT LOADED w/veam (2-120" bars with 8 PARs) Bolt TRS BLV Cam TRS CLV 261 (119) Empty truss includes guide rods & half couplers for rigging lamp bar. PRT 4-WAY SLEEVE FOR 12" TOWER Bolt TRS 2630-S4B CamTRS 2630-S4C 84 (38) ed truss includes lamp bulb weight. T-8 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

17 STAGING, LIGHTING AND SUPPORT SYSTEMS HEAVY DUTY PRE-RIG TRUSS 30" x 30" SPIGOTED * Standard length is 96-1/8" * Available loaded with 2 wired lamp bars of 6 TOMCAT Par 64's * Available in 66" (66-1/8", 4 Par) and 126" (126-1/8", 8 Par) lengths Equipped with asexual steel spigot arrangement Designed for use with color changers Main chords are 2" OD x 3/16" aluminum Diagonals are 1-1/2" OD x 1/8" aluminum Fabricated by certified welders 47.5" (120.65) 39.25" (99.69) 47.5" (120.65) 45.38" (115.26) 98.25" (249.55) OD 38.06" (96.67) 45.38" (115.26) 30" (73.50) 38.63" (98.12) 37.69" (95.73) 38.63" (98.12) 37.69" (95.73) 47.5" (120.65) 45.38" (115.26) PLAN 96.13" (244.17) 2-Way Corner Block 30" (73.50) 3-Way Corner Block Sleeve Version 48.92" (124.25) Horiz. & Vert " (118.87) Horiz. & Vert. 4-Way Corner Block Caster Bar 9.75" (24.71) 8.56" (21.74) 9.5" (24.13) 8.56" (21.74) ELEVATION 35.25" (81.91) 30" (73.50) END VIEW 30" (73.50) Horiz. & Vert. Center Pivot Horizontal Horizontal Articulating Block Variable Corner PLAN VIEWS Connector Orientation Specified by Customer 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-9

18 ALLOWABLE LOAD DATA HEAVY DUTY PRE-RIG TRUSS 30" x 30" SPIGOTED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER Span ft. (mtrs) 8 (2.43) 16 (4.87) 24 (7.31) 32 (9.75) 40 (12.19) 48 (14.63) 56 (17.06) 64 (19.50) #/ft (10352) (9985) (6562) (4810) 8250 (3742) 6632 (3008) 5439 ( 2467) 4485 (2034) Spigots Only (10079) (4994) 7236 (3282) 5315 (2411) 4136 (1876) 3329 (1510) 2735 (1241) 2273 (1031) (5176) (3747) (2462) (1808) (1407) (1133) (930) (773) (3451) (2498) (1641) (1205) (938) (755) (620) (515) Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 96" sections. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, HEAVY DUTY PRE-RIG TRUSS 30" x 30" SPIGOTED Connections are steel spigots & 3/4" clevis pins 66" HDPRT TRUSS (EMPTY) (66-1/8" Pinned length) 96" HDPRT TRUSS (EMPTY) (96-1/8" Pinned length) 126" HDPRT TRUSS (EMPTY) (126-1/8" Pinned length) HDPRT 2-WAY CORNER BLOCK HDPRT 3-WAY CORNER BLOCK HDPRT 4-WAY CORNER BLOCK HDPRT ARTICULATING BLOCK HORIZONTAL (center pivot) HDPRT ARTICULATING BLOCK VERTICAL (center pivot) HDPRT VARIABLE CORNER HORIZ. (book style with brace) HDPRT VARIABLE CORNER VERT. (book style with brace) HDPRT 2-WAY SLEEVE FOR 16" TOWER HDPRT 3-WAY SLEEVE FOR 16" TOWER HDPRT 4-WAY SLEEVE FOR 16" TOWER 3/4" CLEVIS PIN MEDIUM R-CLIP Item Code TRS S TRS S TRS S TRS 3030-C2S TRS 3030-C3S TRS 3030-C4S TRS 3030-AHS TRS 3030-AVS TRS 3030-VHS TRS 3030-VVS TRS 3030-S2S TRS 3030-S3S TRS 3030-S4S HDW CP-75 HDW RC-MED Weight 122 (55) 147 (67) 164 (74) 109 (50) 134 (61) 160 (73) 97 (44) 93 (42) 78 (36) 78 (36) 159 (72) 181 (82) 204 (92).4 (.18) Empty truss includes guide rods & half couplers for rigging lamp bar. HEAVY DUTY PRE-RIG TRUSS (ed) 30" x 30" SPIGOTED ed truss includes guide rods, half couplers, silver PAR 64s hard-wired to bar, and multipin connector Weight Item Code 66" HDPRT LOADED w/socapex (2-60" bars with 4 PARs) 66" HDPRT LOADED w/veam (2-60" bars with 4 PARs) 96" HDPRT LOADED w/socapex (2-90" bars with 6 PARs) 96" HDPRT LOADED w/veam (2-90" bars with 6 PARs) 126" HDPRT LOADED w/socapex (2-120" bars with 8 PARs) 126" HDPRT LOADED w/veam (2-120" bars with 8 PARs) ed truss includes lamp bulb weight. TRS SLS TRS SLV TRS SLS TRS SLV TRS SLS TRS SLV 192 (88) 192 (88) 247 (113) 247 (113) 294 (134) 294 (134) T-10 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

19 STAGING, LIGHTING AND SUPPORT SYSTEMS SUPER BEAM TRUSS 13.7" x 10" SPIGOTED * Standard lengths are 12', 10', 8' and 5' * Custom lengths available upon request Equipped with aluminum spigot connections Main chords are 2" OD x 3/16" aluminum Diagonals are 1" OD x 1/8" aluminum Fabricated by certified welders 17.49" (44.42) 24.1" (61.21) 16.56" (42.06) 22.24" (56.48) " (309.52) OD 10.14" (25.75) 17.12" (43.48) 16.19" (41.12) 17.12" (43.48) 16.19" (41.12) PLAN 2-Way Corner Block 3-Way Corner Block 24.1" (61.21) 22.24" (56.48) 120" (304.80) 10.14" (25.75) 13.78" (35.00) 24.1" (61.21) 22.24" (56.48) ELEVATION END VIEW 4-Way Corner Block PLAN VIEWS Connector Orientation Specified by Cutomer 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-11

20 ALLOWABLE LOAD DATA SUPER BEAM TRUSS 13.7" x 10" SPIGOTED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER Span ft. (mtrs) #/ft. Spigots Only (3.05) (6.09) (9.14) (3475) (1687) (1061) (1738) (845) (537) (1303) (634) (403) (869) (423) (269) (12.21) (744) (375) (281) (187) 2.35 Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 10'-0" sections. Other section lengths are available. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, SUPER BEAM TRUSS 13.7" x 10" SPIGOTED Connections are aluminum spigots & 5/8" clevis pins 5' SUPER BEAM TRUSS Item Code TRS S Weight 44 (20) 8' SUPER BEAM TRUSS TRS S 64 (29) 10' SUPER BEAM TRUSS TRS S 77 (35) 12' SUPER BEAM TRUSS TRS S 88 (40) SUPER BEAM 2-WAY CORNER BLOCK SUPER BEAM 3-WAY CORNER BLOCK SUPER BEAM 4-WAY CORNER BLOCK 3/4" CLEVIS PIN TRS 1310-C2S TRS 1310-C3S TRS 1310-C4S HDW CP (12) 38 (17) 46 (21).4 (.18) MEDIUM R-CLIP HDW RC-MED T-12 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

21 STAGING, LIGHTING AND SUPPORT SYSTEMS LIGHT DUTY TRUSS 12" x 12" SPIGOTED * Standard lengths are 10', 8' and 5' * Custom lengths available upon request Equipped with steel spigot connections Main chords are 2" OD x 3/16" aluminum Diagonals are 1" OD x 1/8" aluminum Fabricated by certified welders 20.88" (53.02) 29.50" (53.02) 19.69" (50.01) 27.38" (50.01) 12" (30.48) 20.96" (53.33) 20.06" (50.96) 20.88" (53.33) 19.69" (50.96) PLAN 2-Way Corner Block 3-Way Corner Block 29.50" (53.02) 27.38" (50.01) 120" (304.80) 12" (30.48) 12" (30.48) 29.50" (53.02) 27.38" (50.01) ELEVATION END VIEW 4-Way Corner Block PLAN VIEWS Connector Orientation Specified by Cutomer 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-13

22 ALLOWABLE LOAD DATA LIGHT DUTY TRUSS 12" x 12" SPIGOTED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER Span ft. (mtrs) #/ft. Spigots Only (3.05) (6.09) (9.14) (5207) (2803) (1510) (3531) (1405) (947) (2604) (1054) (556) (1736) (702) (398) (12.21) (743) (373) (278) (186) 2.52 Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 10'-0" sections. Other section lengths are available. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, LIGHT DUTY TRUSS 12" x 12" SPIGOTED Connections are steel spigots & 3/4" clevis pins 5' 12" x 12" SPIGOTED TRUSS Item Code TRS S Weight 61 (27.7) 8' 12" x 12" SPIGOTED TRUSS TRS S 80 (36.3) 10' 12" x 12" SPIGOTED TRUSS TRS S 92 (41.7) 12" x 12" SPIGOTED 2-WAY CORNER BLOCK 12" x 12" SPIGOTED 3-WAY CORNER BLOCK 12" x 12" SPIGOTED 4-WAY CORNER BLOCK 12" x 12" SPIGOTED 5-WAY CORNER BLOCK 12" x 12" SPIGOTED 6-WAY CORNER BLOCK 3/4" CLEVIS PIN TRS 1212-C2S TRS 1212-C3S TRS 1212-C4S TRS 1212-C5S TRS 1212-C6S HDW CP (17.7) 54 (24.5) 66 (29.9) 81 (36.7) 95 (43.1).4 (.18) MEDIUM R-CLIP HDW RC-MED T-14 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

23 STAGING, LIGHTING AND SUPPORT SYSTEMS LIGHT DUTY TRUSS 12" x 12" PLATED * Standard lengths are 10', 8' and 5' * Custom lengths available upon request Equipped with single Camlocs or bolts Main chords are 2" OD x 1/8" aluminum Diagonals are 1" OD x 1/8" aluminum Fabricated by certified welders 12.75" (32.39) 12.75" (32.39) 12.75" (32.39) 12" (30.48) 12.38" (31.45) 12.38" (31.45) 12.75" (32.39) PLAN 2-Way Corner Block 3-Way Corner Block 4-Way Corner Block 5-Way & 6-Way Available 19.30" (49.02) Horiz. & Vert. 120" (304.8) 12" (30.48) ELEVATION END VIEW 12" (30.48) PLAN VIEWS 12" (30.48) Horiz. & Vert. Center Pivot Horizontal Articulating Block 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-15

24 ALLOWABLE LOAD DATA LIGHT DUTY TRUSS 12" x 12" PLATED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER Span ft. (mtrs) #/ft. Single Camloc through 3/8" gusset plates 10 (3.04) (1397) (700) (525) (350) (6.09) (644) (326) (244) (163) (9.14) (381) (191) (143) (95) (12.21) (218) (115) (86) (58) /8" diameter Grade 8 bolts with standard washers through 3/8" gusset plates 10 (3.04) (2023) (1012) (759) (506) (6.09) (962) (482) (362) (241) (9.14) (585) (295) (221) (147) (12.21) (381) (193) (145) (97) 2.10 Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 10'-0" sections. Other section lengths are available. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, LIGHT DUTY TRUSS 12" x 12" PLATED Connections are single sets of bolts or Camlocs 5' LIGHT DUTY TRUSS 12" X 12" 8' LIGHT DUTY TRUSS 12" X 12" 10' LIGHT DUTY TRUSS 12" X 12" LIGHT DUTY 12" X 12" 2-WAY CORNER BLOCK LIGHT DUTY 12" X 12" 3-WAY CORNER BLOCK LIGHT DUTY 12" X 12" 4-WAY CORNER BLOCK LIGHT DUTY 12" X 12" 5-WAY CORNER BLOCK LIGHT DUTY 12" X 12" 6-WAY CORNER BLOCK LIGHT DUTY 12" X 12" HORIZ. ARTICULATING BLOCK LIGHT DUTY 12" X 12" VERT. ARTICULATING BLOCK Item Code Bolt TRS B Cam TRS C Bolt TRS B Cam TRS C Bolt TRS B Cam TRS C Bolt TRS 1212-C2B Cam TRS 1212-C2C Bolt TRS 1212-C3B Cam TRS 1212-C3C Bolt TRS 1212-C4B Cam TRS 1212-C4C Bolt TRS 1212-C5B Cam TRS 1212-C5C Bolt TRS 1212-C6B Cam TRS 1212-C6C Bolt TRS 1212-AHB Cam TRS 1212-AHC Bolt TRS 1212-AVB Cam TRS 1212-AVC Weight 36 (16) 51 (23) 61 (28) 16 (7) 20 (9) 22 (10) 26 (12) 28 (13) 33 (15) 33 (15) T-16 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

25 STAGING, LIGHTING AND SUPPORT SYSTEMS LIGHT DUTY TRUSS 12" x 18" PLATED * Standard lengths are 10', 8' and 5' * Custom lengths available upon request Equipped with single Camlocs or bolts Main chords are 2" OD x 1/8" aluminum Diagonals are 1" OD x 1/8" aluminum Fabricated by certified welders 18.75" (47.62) 18.75" (47.62) 18.75" (47.62) 18.38" (46.68) 18.38" (46.68) 18.75" (47.62) PLAN 18" (45.72) 2-Way Corner Block 3-Way Corner Block 4-Way Corner Block 6.75" (17.14) 6.75" (17.14) 120" (304.80) 18" (45.72) ELEVATION END VIEW 12" (30.48) Horizontal Variable Corner PLAN VIEWS 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-17

26 ALLOWABLE LOAD DATA LIGHT DUTY TRUSS 12" x 18" PLATED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER Span ft. (mtrs) #/ft (3.04) (6.09) (9.14) (1397) (644) (367) (699) (324) (188) (524) (243) (141) (350) (162) (94) (12.21) (218) (111) (83) (55) /8" diameter Grade 8 bolts with standard washers through 3/8" gusset plates 10 (3.04) (2019) (1011) (758) (506) (6.09) (953) (480) (360) (240) (9.14) (572) (292) (219) (146) (12.21) (363) (189) (142) (94) 2.10 Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 10'-0" sections. Other section lengths are available. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, Single Camloc through 3/8" gusset plates LIGHT DUTY TRUSS 12" x 18" PLATED Connections are single sets of bolts or Camlocs 5' LIGHT DUTY TRUSS 12" X 18" 8' LIGHT DUTY TRUSS 12" X 18" 10' LIGHT DUTY TRUSS 12" X 18" LIGHT DUTY 12" X 18" 2-WAY CORNER BLOCK LIGHT DUTY 12" X 18" 3-WAY CORNER BLOCK LIGHT DUTY 12" X 18" 4-WAY CORNER BLOCK LD 12" X 18" ARTICULATING BLOCK VERTICAL (center pivot) LD 12" X 18" VARIABLE CORNER VERT. (book style with brace pivot) Item Code Bolt TRS B Cam TRS C Bolt TRS B Cam TRS C Bolt TRS B Cam TRS C Bolt TRS 1218-C2B Cam TRS 1218-C2C Bolt TRS 1218-C3B Cam TRS 1218-C3C Bolt TRS 1218-C4B Cam TRS 1218-C4C Bolt TRS 1218-AVB Cam TRS 1218-AVC Bolt TRS 1218-VVB Cam TRS 1218-VVC Weight 39 (18) 57 (26) 67 (30) 19 (9) 21 (10) 25 (11) 29 (13) 30 (13) T-18 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

27 STAGING, LIGHTING AND SUPPORT SYSTEMS BALLROOM TRUSS 12" x 30" SPIGOTED * Standard lengths are 5', 8', and 10' * Custom lengths available upon request Equipped with aluminum spigot connections Main chords are 2" OD x 3/16" aluminum Diagonals are 1" OD x 1/8" aluminum Fabricated by certified welders " (318.18) OD 38.88" (98.74) 37.69" (95.73) 47.50" (120.64) 45.38" (115.25) 30" (76.20) 39.00" (99.05) 38.06" (96.68) 38.88" (98.74) 37.69" (95.73) PLAN 2-Way Corner Block 3-Way Corner Block 47.50" (120.64) 45.38" (115.25) 120" (304.8) 30" (76.20) 12" (30.48) 47.50" (120.64) 45.38" (115.25) ELEVATION END VIEW 4-Way Corner Block PLAN VIEWS Connector Orientation Specified by Cutomer 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-19

28 ALLOWABLE LOAD DATA BALLROOM TRUSS 12" x 30" SPIGOTED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER Span ft. (mtrs) #/ft. Spigots Only (1.52) (3.04) (4.57) (6.09) (7.62) (9.14) (5153) (5080) (4626) (2749) (2177) (1429) (5153) (2857) (2316) (1377) (1334) (860) (2577) (2143) (1412) (1033) (802) (525) (1718) (1429) (1129) (689) (575) (377) (10.67) 40 (12.21) (953) (617) (557) (316) (353) (237) (253) (158) Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 10'-0" sections. Other section lengths are available. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, BALLROOM TRUSS 12" x 30" SPIGOTED Connections are steel spigots & 3/4" clevis pins 5' 12" x 30" BALLROOM TRUSS Item Code TRS S Weight 75 (34.0) 8' 12" x 30" BALLROOM TRUSS TRS S 105 (47.6) 10' 12" x 30" BALLROOM TRUSS TRS S 126 (57.2) 12" x 30" SPIGOTED 2-WAY CORNER BLOCK TRS MS 45 (20.4) 12" x 30" SPIGOTED 3-WAY CORNER BLOCK TRS MS 56 (25.4) 12" x 30" SPIGOTED 4-WAY CORNER BLOCK TRS MS 68 (30.9) 3/4" CLEVIS PIN HDW CP-75.4 (.18) MEDIUM R-CLIP HDW RCMED T-20 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

29 STAGING, LIGHTING AND SUPPORT SYSTEMS MEDIUM DUTY TRUSS 20.5" x 20.5" SPIGOTED * Standard lengths are 10', 8' and 5' * Custom lengths available upon request Equipped with steel spigot connections Available with casters Main chords are 2" OD x 3/16" aluminum Diagonals are 1" OD x 1/8" aluminum Fabricated by certified welders Studio version available 29.50" (74.93) 28.56" (72.54) 38" (96.52) 35.88" (91.13) 38" (96.52) 35.88" (91.13) " (318.18) OD 29.38" (74.62) 28.18" (71.57) 29.12" (73.96) 28.18" (71.57) 38" (96.52) 35.88" (91.13) 20.5" (52.07) 2-Way Corner Block 3-Way Corner Block Sleeve Version 4-Way Corner Block 5-Way & 6-Way Available PLAN 39.42" (100.12) Horiz. & Vert " (94.74) Horiz. & Vert. 9.50" (24.13) 8.31" (21.10) 8.31" (21.10) 9.24" (23.46) 120" (304.80) 20.5" (52.07) 20.5" (52.67) Horiz. & Vert. ELEVATION END VIEW 20.5" (52.07) Center Pivot Horizontal Horizontal Articulating Block Variable Corner PLAN VIEWS Connector Orientation Specified by Customer 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-21

30 ALLOWABLE LOAD DATA MEDIUM DUTY TRUSS 20.5" x 20.5" SPIGOTED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER No. of 10' Sections Span ft. (mtrs) (3.04) (6.09) (9.14) (12.21) (15.24) #/ft (4173) 9000 (4082) 7560 (3429) 5480 (2486) 3850 (1746) MEDIUM DUTY TRUSS 20.5" x 20.5" SPIGOTED Connections are steel spigots & 3/4" clevis pins Spigots Only (4175) (2630) (1715) (1246) (957) (2087) (1972) (1286) (935) (648) (1392) 2898 (1315) 1891 (858) 1374 (623) 1025 (465) Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 10'-0" sections. Other section lengths are available. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, Item Code Weight Item Code Weight 5' STUDIO TRUSS TRS 20ST-060S 80 (37) 5' MEDIUM DUTY TRUSS TRS S 79 (36) 8' STUDIO TRUSS TRS 20ST-096S 106 (49) 8' MEDIUM DUTY TRUSS TRS S 104 (47) 10' STUDIO TRUSS TRS 20ST-120S 117 (54) 10' MEDIUM DUTY TRUSS TRS S 115 (53) MEDIUM DUTY 2-WAY CORNER TRS 2020-C2S 67 (31) 3/4" CLEVIS PIN HDW CP-75.4 (.18) MEDIUM DUTY 3-WAY CORNER TRS 2020-C3S 90 (41) MEDIUM R-CLIP HDW RC-MED MEDIUM DUTY 4-WAY CORNER TRS 2020-C4S 113 (51) MEDIUM DUTY 5-WAY CORNER TRS 2020-C5S 142 (65) MEDIUM DUTY 6-WAY CORNER TRS 2020-C6S 168 (77) MD ARTICULATING HORIZ. (center pivot) TRS 2020-AHS 82 (38) MD ARTICULATING VERT. (center pivot) TRS 2020-AVS 82 (38) MD VARIABLE CORNER HORIZ. (book style with brace) TRS 2020-VHS 62 (28) MD VARIABLE CORNER VERT. (book style with brace) TRS 2020-VVS 62 (28) MD 2-WAY SLEEVE FOR 12" TOWER TRS 2020-S2S 79 (36) MD 3-WAY SLEEVE FOR 12" TOWER TRS 2020-S3S 101 (46) MD 4-WAY SLEEVE FOR 12" TOWER TRS 2020-S4S 124 (57) T-22 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

31 STAGING, LIGHTING AND SUPPORT SYSTEMS MEDIUM DUTY TRUSS 20.5" x 20.5" PLATED Studio M-D Truss (3/16" Chords) M-D Truss (1/8" Chords) Equipped with single Camlocs or bolts * Standard lengths are 10', 8' and 5' * Custom lengths available upon request Available with double Camlocs Available with casters Diagonals are 1" OD x 1/8" aluminum Fabricated by certified welders 21.25" (53.97) 21.25" (53.97) 21.25" (53.97) 20.88" (53.03) 20.88"(53.03) 21.25" (53.03) PLAN 2-Way Corner Block 3-Way Corner Block 4-Way Corner Block 120" (304.8) 30.17" (76.63) Horiz. & Vert. 6.75" (17.14) 6.75" (17.14) 20.5" (52.07) Horiz. & Vert. 20.5" (52.07) 5-Way & 6-Way Available Sleeve Version 20.5" (52.07) 20.5" (52.07) ELEVATION END VIEW Center Pivot Horizontal Articulating Block PLAN VIEWS Horizontal Variable Corner 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-23

32 ALLOWABLE LOAD DATA MEDIUM DUTY TRUSS 20.5" x 20.5" PLATED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER Span ft. (mtrs) 10 (3.04) 20 (6.09) 30 (9.14) 40 (12.21) 50 (15.24) 10 (3.04) 20 (6.09) 30 (9.14) 40 (12.21) 50 (15.24) 10 (3.04) 20 (6.09) 30 (9.14) 40 (12.21) 50 (15.24) #/ft (2985) (1424) (885) (581) (386) (3806) (2359) (1497) (1052) (771) (1493) (717) (445) (298) (203) (2420) (1180) (753) (530) (388) Single Camloc through 3/8" gusset plates Two Camlocs through 3/8" gusset plates (1120) (538) (333) (224) (152) (1815) (885) (565) (397) (291) /8" Diameter Grade 8 bolts with standard washers through 3/8" gusset plates (3806) (2087) (1320) (925) (658) (2152) (1046) (664) (463) (334) (747) (358) (222) (149) (101) (1210) (590) (377) (265) (194) Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 10'-0" sections. Other section lengths are available. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, MEDIUM DUTY TRUSS 20.5" x 20.5" PLATED End plates equipped for double sets of bolts or Camlocs, supplied with one set only (1614) (784) (498) (347) (251) (1076) (523) (332) (231) (167) Item Code Weight Item Code Weight 5' MEDIUM DUTY TRUSS Bolt TRS B Cam TRS C 56 (25) 5' MEDIUM DUTY TRUSS (Studio) Bolt TRS 20ST-060B Cam TRS 20ST-060C 66 (30) 8' MEDIUM DUTY TRUSS Bolt TRS B Cam TRS C 77 (35) 8' MEDIUM DUTY TRUSS (Studio) Bolt TRS 20ST-096B Cam TRS 20ST-096C 91 (42) 10' MEDIUM DUTY TRUSS Bolt TRS B Cam TRS C 85 (39) 10 MEDIUM DUTY TRUSS (Studio) Bolt TRS 20ST-120B Cam TRS 20ST-120C 102 (47) MEDIUM DUTY 2-WAY CORNER Bolt TRS 2020-C2B Cam TRS 2020-C2C 31 (14) MD ARTICULATING BLOCK HORIZONTAL (center pivot) Bolt TRS 2020-AHB Cam TRS 2020-AHC 59 (27) MEDIUM DUTY 3-WAY CORNER Bolt TRS 2020-C3B Cam TRS 2020-C3C 32 (15) MD ARTICULATING BLOCK VERTICAL (center pivot) Bolt TRS 2020-AVB Cam TRS 2020-AVC 59 (27) MEDIUM DUTY 4-WAY CORNER Bolt TRS 2020-C4B Cam TRS 2020-C4C 39 (18) MD VARIABLE CORNER HORIZ. (book style with brace) Bolt TRS 2020-VHB Cam TRS 2020-VHC 45 (21) MEDIUM DUTY 5-WAY CORNER Bolt TRS 2020-C5B Cam TRS 2020-C5C 52 (24) MD VARIABLE CORNER VERT. (book style with brace) Bolt TRS 2020-VVB Cam TRS 2020-VVC 45 (21) MEDIUM DUTY 6-WAY CORNER Bolt TRS 2020-C6B Cam TRS 2020-C6C 58 (27) MD 2-WAY SLEEVE FOR 12" TOWER Bolt TRS 2020-S2B Cam TRS 2020-S2C 43 (20) MD 3-WAY SLEEVE FOR 12" TOWER Bolt TRS 2020-S3B Cam TRS 2020-S3C 50 (23) MD 4-WAY SLEEVE FOR 12" TOWER Bolt TRS 2020-S4B Cam TRS 2020-S4C 56 (26) T-24 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

33 STAGING, LIGHTING AND SUPPORT SYSTEMS HEAVY DUTY TRUSS 30" x 20.5" SPIGOTED * Standard lengths are 10', 8' and 5' * Custom lengths available upon request Equipped with steel spigot connections Available with casters Main chords are 2" OD x 3/16" aluminum Diagonals are 1-1/2" OD x 1/8" aluminum Fabricated by certified welders 38" (96.52) 29.50" (74.93) 38" (96.52) 35.88" (91.13) 28.56" (72.54) 35.88" (91.13) " (310.18) O.D. 20.5" (52.07) 29.38" (74.62) 28.18" (71.57) 29.12" (73.96) 28.18" (71.57) 38" (96.52) 35.88" (91.13) PLAN 120"(304.8) ELEVATION 2-Way Corner Block 20.5" (52.07) END VIEW 30" (76.20) 3-Way Corner Block 39.42" (100.12) Horiz (124.25) Vert " (94.74) Horiz (118.87) Vert. Center Pivot Horizontal Articulating Block 20.5" (52.07) Horiz. 30" (76.20) Vert. 4-Way Corner Block Sleeve Version 9.50" (24.13) 8.31" (21.10) 9.24" 8.31" (23.46) (21.10) Horizontal Variable Corner PLAN VIEWS Connector Orientation Specified by Customer 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-25

34 ALLOWABLE LOAD DATA HEAVY DUTY TRUSS 30" x 20.5" SPIGOTED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER No. of 10' Sections Span ft. (mtrs) #/ft. Spigots Only (3.04) (6.09) (9.14) (12.21) (15.24) (18.29) (16125) (7956) (5185) 8320 (3774) 6350 (2880) 4710 (2136) (8065) (3980) (2597) (1888) (1449) (1069) (6046) (2985) (1948) (1416) (1087) (802) (4032) (1990) (1299) (944) (725) (534) Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 10'-0" sections. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, HEAVY DUTY TRUSS 30" x 20.5" SPIGOTED Connections are steel spigots & 3/4" clevis pins 5' HEAVY DUTY TRUSS Item Code TRS S Weight 90 (41) 8' HEAVY DUTY TRUSS TRS S 120 (55) 10' HEAVY DUTY TRUSS TRS S 132 (60) HEAVY DUTY 2-WAY CORNER HEAVY DUTY 3-WAY CORNER HEAVY DUTY 4-WAY CORNER HD ARTICULATING BLOCK HORIZONTAL (center pivot) HD ARTICULATING BLOCK VERTICAL (center pivot) HD VARIABLE CORNER HORIZ. (book style with brace) HD VARIABLE CORNER VERT. (book style with brace) HD 2-WAY SLEEVE FOR 12" TOWER* HD 3-WAY SLEEVE FOR 12" TOWER* HD 4-WAY SLEEVE FOR 12" TOWER* 3/4" CLEVIS PIN TRS 3020-C2S TRS 3020-C3S TRS 3020-C4S TRS 3020-AHS TRS 3020-AVS TRS 3020-VHS TRS 3020-VVS TRS 3020-S2S TRS 3020-S3S TRS 3020-S4S HDW CP (35) 95 (43) 121 (55) 91 (42) 92 (42) 72 (33) 68 (31) 97 (44) 115 (53) 141 (64).4 (.18) MEDIUM R-CLIP HDW RC-MED * Spans greater than 40' require custom sleeves for larger tower. T-26 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

35 STAGING, LIGHTING AND SUPPORT SYSTEMS HEAVY DUTY TRUSS 30" x 20.5" PLATED * Standard lengths are 10', 8' and 5' * Custom lengths available upon request Equipped with single Camlocs or bolts Available with double Camlocs Available with casters Main chords are 2" OD x 1/8" aluminum Diagonals are 1" OD x 1/8" aluminum Fabricated by certified welders 21.25" (53.97) 21.25" (53.97) 21.25" (53.97) 20.5" (52.07) 20.88" (53.03) 2-Way Corner Block 20.88" (53.03) 3-Way Corner Block 21.25" (53.97) 4-Way Corner Block PLAN 120" (304.80) ELEVATION 20.5" (52.07) END VIEW 30" (76.20) 30.18" (76.65) Horiz " (100.76) Vert. 20.5" Horiz. (52.07) 30" Vert. (76.20) Center Pivot Horizontal Articulating Block PLAN VIEWS Vertical Variable Corner Available 6.75" 6.75" (17.14) (17.14) Horizontal Variable Corner 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-27

36 ALLOWABLE LOAD DATA HEAVY DUTY TRUSS 30" x 20.5" PLATED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER Span ft. (mtrs) #/ft (3.04) (6.09) (9.14) (2649) (2313) (1456) (2381) (1157) (734) (1325) (868) (550) (883) (578) (367) (12.21) 50 (15.24) 60 (18.28) (1016) (726) (517) (511) (368) (266) (383) (276) (199) (255) (184) (133) Two Camlocs through 3/8" gusset plates 10 (3.04) (2649) (2649) (1325) (883) (6.09) (2604) (1893) (1302) (868) (9.14) (2449) (1225) (917) (612) (12.21) (1742) (879) (660) (440) (15.24) (1315) (663) (497) (332) (18.28) (1007) (511) (383) (255) /8" diameter Grade 8 bolts with standard washers through 3/8" gusset plates 10 (3.04) (2649) (2649) (1325) (883) (6.09) (2604) (1680) (1260) (840) (9.14) (2164) (1083) (812) (541) (12.21) (1542) (772) (579) (386) (15.24) (1134) (577) (433) (289) (18.28) (871) (440) (330) (220) 2.05 Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 10'-0" sections. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, Single Camloc through 3/8" gusset plates HEAVY DUTY TRUSS 30" x 20.5" PLATED End plates equipped for double sets of bolts or Camlocs, supplied with one set only Item Code Weight Item Code Weight 5' HEAVY DUTY TRUSS Bolt TRS B Cam TRS C 63 (28) HD ARTICULATING BLOCK VERTICAL (center pivot) Bolt TRS 3020-AVB Cam TRS 3020-AVC 67 (31) 8' HEAVY DUTY TRUSS Bolt TRS B Cam TRS C 86 (39) HD VARIABLE CORNER HORIZ. (book style with brace) Bolt TRS 3020-VHB Cam TRS 3020-VHC 55 (25) 10' HEAVY DUTY TRUSS Bolt TRS B Cam TRS C 94 (43) HD VARIABLE CORNER VERT. (book style with brace) Bolt TRS 3020-VVB Cam TRS 3020-VVC 50 (23) HEAVY DUTY 2-WAY CORNER Bolt TRS 3020-C2B Cam TRS 3020-C2C 35 (16) HD 2-WAY SLEEVE BLOCK FOR 12" TOWER* Bolt TRS 3020-S2B Cam TRS 3020-S2C 46 (21) HEAVY DUTY 3-WAY CORNER Bolt TRS 3020-C3B Cam TRS 3020-C3C 42 (19) HD 3-WAY SLEEVE BLOCK FOR 12" TOWER* Bolt TRS 3020-S3B Cam TRS 3020-S3C 53 (24) HEAVY DUTY 4-WAY CORNER Bolt TRS 3020-C4B Cam TRS 3020-C4C 47 (21) HD 4-WAY SLEEVE BLOCK FOR 12" TOWER* Bolt TRS 3020-S4B Cam TRS 3020-S4C 59 (27) HD ARTICULATING BLOCK HORIZONTAL (center pivot) Bolt TRS 3020-AHB Cam TRS 3020-AHC 67 (31) * Spans greater than 40' require custom sleeves for larger tower. T-28 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

37 STAGING, LIGHTING AND SUPPORT SYSTEMS EXTRA HEAVY DUTY TRUSS 36" x 24" SPIGOTED * Standard lengths are 20', 10' and 5' * Custom lengths available upon request Equipped with steel spigot connections Main chords are 3" OD x 1/4" aluminum Diagonals are 1-1/2" OD x 1/8" aluminum Fabricated by certified welders 123" (312.42) 35" (88.90) 33.5" (85.09) 45.51" (115.59) 42" (106.68) 24" (60.96) PLAN 120" (304.80) 24" (60.96) 40.75" (103.50) 36" (91.44) 45.51" (115.59) 42" (106.68) 34.51" (87.65) 33" (83.82) 34.51" (87.65) 33" (83.82) 2-Way Corner Block Sleeve Version Caster Bar 3-Way Corner Block 45.51" (115.59) 42" (106.68) ELEVATION END VIEW 4-Way Corner Block PLAN VIEWS Connector Orientation Specified by Customer 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-29

38 ALLOWABLE LOAD DATA EXTRA HEAVY DUTY TRUSS 36" x 24" SPIGOTED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER Span ft. (mtrs) (3.04) (6.09) (9.14) (12.21) (15.24) (18.28) (21.33) (24.38) #/ft (9380) (9172) (8954) (8745) (8528) (5851) 9240 (4191) 5440 (2468) Spigots Only (9382) (9172) (7746) (4656) (4480) (2929) (2109) (1240) (4691) (4586) (4482) (3492) (2731) (2197) (1582) (930) (3127) 6741 (3058) 6587 (2988) 5132 (2328) 4459 (2023) 3229 (1465) 2324 (1054) 1366 (620) Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 10' sections. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, EXTRA HEAVY DUTY TRUSS 36" x 24" SPIGOTED Connections are steel spigots & 1" clevis pins 5' EXTRA HEAVY DUTY TRUSS Item Code TRS S Weight 171 (78) 10' EXTRA HEAVY DUTY TRUSS TRS S 249 (113) 20' EXTRA HEAVY DUTY TRUSS TRS S 402 (182) EXTRA HEAVY DUTY 2-WAY CORNER BLOCK EXTRA HEAVY DUTY 3-WAY CORNER BLOCK EXTRA HEAVY DUTY 4-WAY CORNER BLOCK EXTRA HEAVY DUTY 2-WAY SLEEVE BLOCK FOR 16" TOWER* EXTRA HEAVY DUTY 3-WAY SLEEVE BLOCK FOR 16" TOWER* EXTRA HEAVY DUTY 4-WAY SLEEVE BLOCK FOR 16" TOWER* 1" CLEVIS PIN TRS 3624-C2S TRS 3624-C3S TRS 3624-C4S TRS 3624-S2S TRS 3624-S3S TRS 3624-S4S HDW CP (79) 226 (103) 278 (126) 270 (123) 325 (148) 380 (173) 1 (.46) LARGE R-CLIP HDW RC-LG * Spans greater than 60' require custom sleeves for larger tower. T-30 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

39 STAGING, LIGHTING AND SUPPORT SYSTEMS STACKING TRUSS 25" SPIGOTED Fully Assembled Snap Hooks in Place * Standard lengths are 10', 8' and 5' * Custom lengths available upon request Equipped with steel spigot connections Main chords are 1.90" OD (4.83cm) x.1875"(.48cm) aluminum Diagonals are 1.50" (3.81cm) OD x 1/8" (.32cm) aluminum Fabricated by certified welders Snap Braces provided 38.42" (97.58) 37.49" (95.23) Snap Hooks in Stored Position 46.91" (119.15) 45.09" (114.53) " (305.38) 38.79" (98.53) 37.91" (96.28) (97.59) 37.49" (95.23) 13.71" (34.82) 29.94" (76.05) 2-Way Corner Block 3-Way Corner Block 46.91" (119.15) 45.09" (114.53) PLAN " (300) 30.66" (77.88) Snap Hooks 5.69" (14.45) 46.91" (119.15) 45.09" (114.53) 25.18" (58.92) 24.64" (62.57) 4-Way Corner Block ELEVATION END VIEW PLAN VIEWS Connector Orientation Specified by Customer 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-31

40 ALLOWABLE LOAD DATA STACKING TRUSS 25" SPIGOTED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER Span ft. (mtrs) #/ft. Spigots Only 10 (3.04) (5021) (4629) (2472) (1648) (6.10) (4636) (2283) (1712) (1142) (9.14) (3021) (1487) (1115) (743) (12.19) (2177) (1078) (809) (539) (15.24) (1656) (825) (619) (412) (18.29) (1306) (649) (486) (324) 3.39 Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 10'-0" sections. Other section lengths are available. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, STACKING TRUSS 25" SPIGOTED Connections are steel spigots & 5/8" clevis pins 5' STACKING TRUSS Item Code TRS 25SK-060S Weight 45 (20.4) 8' STACKING TRUSS TRS 25SK-096S 72 (32.7) 10' STACKING TRUSS TRS 25SK-120S 90 (40.8) 2m STACKING TRUSS TRS 25SK-20MS 114 (51.7) 2.5m STACKING TRUSS TRS 25SK-25MS 143 (64.9) 3m STACKING TRUSS TRS 25SK-30MS 172 (78.0) 4m STACKING TRUSS TRS 25SK-40MS 229 (103.9) STACKING TRUSS 2-WAY CORNER BLOCK TRS 25SK-C2S 96 (43.52) STACKING TRUSS 3-WAY CORNER BLOCK TRS 25SK-C3S 120 (54.40) STACKING TRUSS 4-WAY CORNER BLOCK 5/8" CLEVIS PIN TRS 25SK-C4S HDW CP (64.83).25 (.11) MEDIUM R-CLIP HDW RCMED T-32 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

41 STAGING, LIGHTING AND SUPPORT SYSTEMS FIXED TRIANGULAR TRUSS 20.5" SPIGOTED * Standard lengths are 10', 8' and 5' * Custom lengths available upon request Equipped with steel spigot connections Main chords are 2" OD x 3/16" aluminum Diagonals are 1" OD x 1/8" aluminum Fabricated by certified welders 29.50" (74.93) 28.56" (72.54) 38" (96.52) 35.88" (91.13) " (310.18) OD 29.38" (74.62) 28.19" (71.60) 29.12" (73.96) 28.19" (71.60) 20.5" (52.07) 2-Way Corner Block 3-Way Corner Block PLAN 38" (96.52) 35.88" (91.13) 120" (304.80) 20.5" (52.07) 20.5" (52.07) 18.02" (45.77) 38" (96.52) 35.88" (91.13) SIDE ELEVATION END VIEW 4-Way Corner Block PLAN VIEWS Connector Orientation Specified by Customer 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-33

42 ALLOWABLE LOAD DATA FIXED TRIANGULAR TRUSS 20.5" SPIGOTED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER No. of 10' Sections Span ft. (mtrs) (3.04) (6.09) (9.14) (12.21) (15.24) #/ft (3506) 4920 (2232) 3120 (1415) 2200 (998) 1600 (726) Spigots Only 6229 (2825) (1119) (714) (502) (366) 2.60 (1754) (840) (535) (376) (275) Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 10'-0" sections. Other section lengths are available. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, (1169) 1234 (560) 787 (357) 553 (251) 404 (183) FIXED TRIANGULAR TRUSS 20.5" SPIGOTED Connections are steel spigots & 3/4" clevis pins 5' FIXED TRIANGULAR TRUSS Item Code TRS 20FX-060S Weight 62 (29) 8' FIXED TRIANGULAR TRUSS TRS 20FX-096S 82 (37) 10' FIXED TRIANGULAR TRUSS TRS 20FX-120S 90 (41) FIXED TRIANGULAR 2-WAY CORNER BLOCK FIXED TRIANGULAR 3-WAY CORNER BLOCK FIXED TRIANGULAR 4-WAY CORNER BLOCK 3/4" CLEVIS PIN TRS 20FX-C2S TRS 20FX-C3S TRS 20FX-C4S HDW CP (22) 63 (29) 80 (36).4 (.18) MEDIUM R-CLIP HDW RC-MED T-34 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

43 STAGING, LIGHTING AND SUPPORT SYSTEMS FIXED TRIANGULAR TRUSS 20.5" PLATED * Standard lengths are 10', 8' and 5' * Custom lengths available upon request Equipped with single Camlocs or bolts Main chords are 2" OD x 1/8" aluminum Diagonals are 1" OD x 1/8" aluminum Fabricated by certified welders 25.38" (64.46) 29.5" (74.93) 20.5" (52.07) 25" (63.50) 25" (63.50) 2-Way Corner Block 3-Way Corner Block PLAN 29.5"(74.93) 120" (304.8) 20.5" (52.07) 20.5" (52.07) 18.02" (45.77) 29.5" (74.93) SIDE ELEVATION END VIEW 4-Way Corner Block PLAN VIEWS 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-35

44 ALLOWABLE LOAD DATA FIXED TRIANGULAR TRUSS 20.5" PLATED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER Span ft. (mtrs) #/ft. Single Camloc through 3/8" gusset plates (3.04) (6.09) (9.14) (1302) (635) (381) (670) (318) (193) (503) (239) (145) (335) (159) (97) /8" diameter Grade 8 bolts with standard washers through 3/8" gusset plates 10 (3.04) (1302) (712) (534) (356) (6.09) (671) (339) (254) (169) (9.14) (408) (207) (155) (103) 0.49 Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 10'-0" sections. Other section lengths are available. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, FIXED TRIANGULAR TRUSS 20.5" PLATED Connections are single sets of bolts or Camlocs 5' FIXED TRIANGULAR TRUSS 8' FIXED TRIANGULAR TRUSS 10' FIXED TRIANGULAR TRUSS FIXED TRIANGULAR 2-WAY CORNER BLOCK FIXED TRIANGULAR 3-WAY CORNER BLOCK FIXED TRIANGULAR 4-WAY CORNER BLOCK Item Code Bolt TRS 20FX-060B Cam TRS 20FX-060C Bolt TRS 20FX-096B Cam TRS 20FX-096C Bolt TRS 20FX-120B Cam TRS 20FX-120C Bolt TRS 20FX-C2B Cam TRS 20FX-C2C Bolt TRS 20FX-C3B Cam TRS 20FX-C3C Bolt TRS 20FX-C4B Cam TRS 20FX-C4C Weight 40 (18) 56 (25) 62 (28) 27 (12) 35 (16) 43 (20) T-36 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

45 STAGING, LIGHTING AND SUPPORT SYSTEMS FOLDING TRIANGULAR TRUSS 14" SPIGOTED * Standard lengths are 10', 8' and 5' * Custom lengths available upon request Equipped with aluminum spigot connections Main chords are 2" OD x 1/8" aluminum Diagonals are 1" OD x 1/8" aluminum Fabricated by certified welders Snap Braces provided to lock truss in open position " (309.52) OD Shipping Width 5.79" (14.70) 22.75" (57.78) 120" (304.8) 17.25" (43.81) Snap Hooks 18.02" (45.77) Shipping Height 14.25" (36.19) PLAN 14" (35.56) ELEVATION END VIEW 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-37

46 ALLOWABLE LOAD DATA FOLDING TRIANGULAR TRUSS 14" SPIGOTED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER Span ft. (mtrs) (3.04) (6.09) (9.14) #/ft (2617) 2780 (1261) 1740 (789) Spigots Only 2889 (1310) (632) (396) 1.20 (983) (474) (297) Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 10'-0" sections. Other section lengths are available. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, (655) (316) (198) FOLDING TRIANGULAR TRUSS 14" SPIGOTED Connections are aluminum spigots & 5/8" clevis pins 5' FOLDING TRIANGULAR TRUSS 14" 8' FOLDING TRIANGULAR TRUSS 14" 10' FOLDING TRIANGULAR TRUSS 14" 5/8" CLEVIS PIN Item Code TRS 14FT-060S TRS 14FT-096S TRS 14FT-120S HDW CP-625 Weight 54 (25) 71 (32) 78 (36).25 (.11) TOP HITCH PIN 5/8" x 4-3/4" HDW HP.57 (.26) MEDIUM R-CLIP HDW RC-MED T-38 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

47 STAGING, LIGHTING AND SUPPORT SYSTEMS FOLDING TRIANGULAR TRUSS 20.5" SPIGOTED * Standard lengths are 10', 8' and 5' * Custom lengths available upon request Equipped with aluminum spigot connections Main chords are 2" OD x 1/8" aluminum Diagonals are 1" OD x 1/8" aluminum Fabricated by certified welders Snap Braces provided to lock truss in open position " (309.52) OD Shipping Width 5.79" (14.70) 22.75" (57.78) Shipping Height 20.75" (52.70) PLAN 120" (304.8) 20.5" (52.07) 23.75" (60.32) Snap Hooks 18.02" (45.77) ELEVATION END VIEW 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-39

48 ALLOWABLE LOAD DATA FOLDING TRIANGULAR TRUSS 20.5" SPIGOTED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER Span ft. (mtrs) (3.04) (6.09) (9.14) (12.21) #/ft (2962) 4340 (1969) 2760 (1252) 1920 (871) Spigots Only 4468 (2027) (988) (630) (443) 1.41 (1481) (741) (473) (332) Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 10'-0" sections. Other section lengths are available. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, (987) (494) (315) (221) FOLDING TRIANGULAR TRUSS 20.5" SPIGOTED Connections are aluminum spigots & 5/8" clevis pins 5' FOLDING TRIANGULAR TRUSS 20.5" 8' FOLDING TRIANGULAR TRUSS 20.5" 10' FOLDING TRIANGULAR TRUSS 20.5" 5/8" CLEVIS PIN Item Code TRS 20FT-060S TRS 20FT-096S TRS 20FT-120S HDW CP-625 Weight 55 (25) 77 (35) 85 (39).25 (.11) TOP HITCH PIN 5/8"x4-3/4" HDW HP.57 (.26) MEDIUM R-CLIP HDW RC-MED T-40 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

49 STAGING, LIGHTING AND SUPPORT SYSTEMS FOLDING TRIANGULAR TRUSS 26" SPIGOTED * Standard lengths are 10', 8' and 5' * Custom lengths available upon request Equipped with aluminum spigot connections Main chords are 2" OD x 1/8" aluminum Diagonals are 1" OD x 1/8" aluminum Fabricated by certified welders Snap Braces provided to lock truss in open position " (309.52) OD Shipping Width 5.79" (14.70) 28.25" (71.75) Shipping Height 6.25" (15.87) PLAN 120" (304.80) 26" (66.04) 29.50" (74.93) Snap Hooks 22.78" (57.86) ELEVATION END VIEW 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-41

50 ALLOWABLE LOAD DATA FOLDING TRIANGULAR TRUSS 26" SPIGOTED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER Span ft. (mtrs) (3.04) (6.09) (9.14) (12.21) (15.24) #/ft (2477) 5380 (2440) 4920 (2232) 3520 (1597) 2650 (1202) Spigots Only 5470 (2481) (1729) (1121) (807) (611) 2.27 (1241) (1221) (841) (605) (458) Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 10'-0" sections. Other section lengths are available. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, (827) (814) (560) (403) (305) FOLDING TRIANGULAR TRUSS 26" SPIGOTED Connections are aluminum spigots & 5/8" clevis pins 5' FOLDING TRIANGULAR TRUSS 26" 8' FOLDING TRIANGULAR TRUSS 26" 10' FOLDING TRIANGULAR TRUSS 26" 5/8" CLEVIS PIN Item Code TRS 26FT-060S TRS 26FT-096S TRS 26FT-120S HDW CP-625 Weight 60 (27) 84 (38) 92 (42).25 (.11) TOP HITCH PIN 5/8"x4-3/4" HDW HP.57 (.26) MEDIUM R-CLIP HDW RC-MED T-42 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

51 STAGING, LIGHTING AND SUPPORT SYSTEMS TTR COMPATIBLE TRUSS * Standard lengths are 8' and 4' * Custom lengths available upon request Equipped with special TTR steel spigot connections Main chords are 1.90" OD x 0.18" aluminum Diagonals are 1-1/2" OD x 1/8" Fabricated by certified welders Snap Braces provided to lock truss in open position 98.21" (249.45) OD Shipping Width 4.67" (11.86) 96.05" (243.96) 26.28" (66.75) 23.25" (59.05) Shipping Height 26.75" (67.94) TOP VIEW 23.88" (60.65) Snap Hooks 26.25" (66.67) ELEVATION END VIEW 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-43

52 ALLOWABLE LOAD DATA TTR COMPATIBLE TRUSS MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER Span ft. (mtrs) (2.43) (4.87) (7.31) (9.75) (12.19) (14.63) #/ft (8005) 8928 (4050) 5784 (2624) 4160 (1887) 3120 (1415) 2448 (1110) Spigots Only 4724 (2143) (2027) (1314) (946) (716) (556) 1.28 (2143) (1520) (985) (709) (537) (417) Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 8'-0" sections. Other section lengths are available. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, (2060) 2234 (1013) 1448 (657) 1043 (473) 789 (358) 612 (278) TTR COMPATIBLE TRUSS Connections are steel spigots & TTR clevis pins 4' TTR COMPATIBLE TRUSS Item Code TRS TTR-048S Weight 67 (30) 8' TTR COMPATIBLE TRUSS TRS TTR-096S 104 (47) TTR PIN HDW HD WCP (.27) MEDIUM R-CLIP HDW RC-MED T-44 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

53 STAGING, LIGHTING AND SUPPORT SYSTEMS MEDIUM DUTY FOLDING TRUSS 20.5" x 20.5" SPIGOTED * Standard lengths are 10', 8' and 5' * Custom lengths available upon request Equipped with steel spigot connections Main chords are 2" OD x 3/16" aluminum Diagonals are 1" OD x 1/8" aluminum Fabricated by certified welders 38" (96.52) 29.50" (74.93) 38" (96.52) 35.88" (91.13) " (356.24) End to End (collapsed) 28.56" (72.54) 35.88" (91.13) " (310.18) O.D " (74.62) 28.18" (71.57) 29.12" (73.96) 28.18" (71.57) 38" (96.52) 35.88" (91.13) 2-Way Corner Block 3-Way Corner Block 4-Way Corner Block 20.5" (52.07) Sleeve Version 5-Way & 6-Way Available PLAN VIEWS 120"(304.8) ELEVATION 20.5" (52.07) 20.5" (52.07) END VIEW 6.25" (15.88) Collapsed 39.42" (100.12) Horiz. & Vert " (94.74) Horiz. & Vert. 20.5" (52.67) Horiz. & Vert. 9.50" (24.13) 8.31" (21.10) 9.24" 8.31" (23.46) (21.10) Center Pivot Horizontal Horizontal Articulating Block Variable Corner PLAN VIEWS Connector Orientation Specified by Customer 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-45

54 ALLOWABLE LOAD DATA MEDIUM DUTY FOLDING TRUSS 20.5" x 20.5" SPIGOTED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER No. of 10' Sections Span ft. (mtrs) (3.04) (6.09) (9.14) (12.21) (15.24) #/ft (4173) 9000 (4082) 7560 (3429) 5480 (2486) 3850 (1746) Spigots Only (4175) (2630) (1715) (1246) (957) (2087) (1972) (1286) (935) (648) (1392) 2898 (1315) 1891 (858) 1374 (623) 1025 (465) Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 10'-0" sections. Other section lengths are available. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, MEDIUM DUTY FOLDING TRUSS 20.5" x 20.5" SPIGOTED Connections are steel spigots & 3/4" clevis pins ' FOLDING MEDIUM DUTY TRUSS Item Code TRS F Weight 85 (38.5) 8' FOLDING MEDIUM DUTY TRUSS TRS F 115 (52.2) 10' FOLDING MEDIUM DUTY TRUSS TRS F 125 (56.7) MEDIUM DUTY 2-WAY CORNER MEDIUM DUTY 3-WAY CORNER MEDIUM DUTY 4-WAY CORNER MEDIUM DUTY 5-WAY CORNER MEDIUM DUTY 6-WAY CORNER MD ARTICULATING HORIZ. (center pivot) MD ARTICULATING VERT. (center pivot) MD VARIABLE CORNER HORIZ. (book style with brace) MD VARIABLE CORNER VERT. (book style with brace) MD 2-WAY SLEEVE FOR 12" TOWER MD 3-WAY SLEEVE FOR 12" TOWER MD 4-WAY SLEEVE FOR 12" TOWER 3/4" CLEVIS PIN TRS 2020-C2S TRS 2020-C3S TRS 2020-C4S TRS 2020-C5S TRS 2020-C6S TRS 2020-AHS TRS 2020-AVS TRS 2020-VHS TRS 2020-VVS TRS 2020-S2S TRS 2020-S3S TRS 2020-S4S HDW CP (31) 90 (41) 113 (51) 142 (65) 168 (77) 82 (38) 82 (38) 62 (28) 62 (28) 79 (36) 101 (46) 124 (57).4 (.18) T-46 MEDIUM R-CLIP HDW RC-MED USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

55 STAGING, LIGHTING AND SUPPORT SYSTEMS HEAVY DUTY FOLDING TRUSS 30" x 20.5" SPIGOTED * Standard lengths are 10', 8' and 5' * Custom lengths available upon request Equipped with steel spigot connections Main chords are 2" OD x 3/16" aluminum Diagonals are 1-1/2" OD x 1/8" aluminum Fabricated by certified welders 38" (96.52) 29.50" (74.93) 38" (96.52) 35.88" (91.13) " (356.24) End to End (collapsed) 28.56" (72.54) 35.88" (91.13) " (310.18) O.D " (74.62) 28.18" (71.57) 29.12" (73.96) 28.18" (71.57) 38" (96.52) 35.88" (91.13) PLAN VIEWS 120"(304.8) ELEVATION 20.5" (52.07) 20.5" (52.07) 2-Way Corner Block 30" (76.20) END VIEW 6.25" (15.88) Collapsed 3-Way Corner Block 39.42" (100.12) Horiz (124.25) Vert " (94.74) Horiz (118.87) Vert. Center Pivot Horizontal Articulating Block 20.5" (52.07) Horiz. 30" (76.20) Vert. 4-Way Corner Block Sleeve Version 9.50" (24.13) 8.31" (21.10) 9.24" 8.31" (23.46) (21.10) Horizontal Variable Corner PLAN VIEWS Connector Orientation Specified by Customer 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-47

56 ALLOWABLE LOAD DATA HEAVY DUTY FOLDING TRUSS 30" x 20.5" SPIGOTED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER No. of 10' Sections Span ft. (mtrs) #/ft. Spigots Only (3.04) (6.09) (9.14) (12.21) (15.24) (18.29) (16125) (7956) (5185) 8320 (3774) 6350 (2880) 4710 (2136) (8065) (3980) (2597) (1888) (1449) (1069) (6046) (2985) (1948) (1416) (1087) (802) (4032) (1990) (1299) (944) (725) (534) Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 10'-0" sections. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, HEAVY DUTY TRUSS 30" x 20.5" SPIGOTED Connections are steel spigots & 3/4" clevis pins 5' HEAVY DUTY TRUSS Item Code TRS S Weight 90 (41) 8' HEAVY DUTY TRUSS TRS S 120 (55) 10' HEAVY DUTY TRUSS TRS S 132 (60) HEAVY DUTY 2-WAY CORNER HEAVY DUTY 3-WAY CORNER HEAVY DUTY 4-WAY CORNER HD ARTICULATING BLOCK HORIZONTAL (center pivot) HD ARTICULATING BLOCK VERTICAL (center pivot) HD VARIABLE CORNER HORIZ. (book style with brace) HD VARIABLE CORNER VERT. (book style with brace) HD 2-WAY SLEEVE FOR 12" TOWER* HD 3-WAY SLEEVE FOR 12" TOWER* HD 4-WAY SLEEVE FOR 12" TOWER* 3/4" CLEVIS PIN TRS 3020-C2S TRS 3020-C3S TRS 3020-C4S TRS 3020-AHS TRS 3020-AVS TRS 3020-VHS TRS 3020-VVS TRS 3020-S2S TRS 3020-S3S TRS 3020-S4S HDW CP (35) 95 (43) 121 (55) 91 (42) 92 (42) 72 (33) 68 (31) 97 (44) 115 (53) 141 (64).4 (.18) MEDIUM R-CLIP HDW RC-MED * Spans greater than 40' require custom sleeves for larger tower. T-48 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

57 STAGING, LIGHTING AND SUPPORT SYSTEMS INTELLIGENT TRUSS 26" x 30" PLATED * Standard length is 93" (for 3 intelligent fixtures) * Available in 63" (for 2 intelligent fixtures) and 123" (for 4 intelligent fixtures) lengths Universal fixture mounting brackets (accepts most intelligent fixtures) One man deployment system Top-mountable headframe Fixture restraint system Compatible with all industry standard Pre-Rigged trussing Main chords are 2" OD x 3/16" aluminum Diagonals are 1" OD x 1/8" aluminum Equipped with bolts or optional spigots (refer to page T-5 for spigoted accessories) 30.75" (78.10) 30.75" (78.10) 30.75" (78.10) 93" (236.22) 31.25" (79.37) 26" (66.04) 30" (76.20) 30.38" (77.16) 30.75" (78.10) 30.75" (78.10) PLAN 2-Way Corner Block 30" (76.20) 3-Way Corner Block Horiz " (100.76) Vert " (90.66) 4-Way Corner Block Sleeve Version 6.75" (17.14) 6.75" (17.14) Horiz. 30" (76.20) Vert. 26" (66.04) ELEVATION END VIEW Center Pivot Horizontal Articulating Block Horizontal Variable Corner PLAN VIEWS 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) T-49

58 ALLOWABLE LOAD DATA INTELLIGENT TRUSS 26" x 30" PLATED MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER No. of 10' Sections Span ft. (mtrs) #/ft. Spigots Only (2.36) (4.72) (7.09) (9.45) (11.81) (14.17) (16.54) (3023) (2946) (2541) (1677) (1160) (801) (517) (3025) (1995) (1202) (811) (569) (399) (267) (1513) (1352) (853) (589) (419) (296) (200) (1008) (947) (584) (399) (282) (198) (133) Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 7'-9" sections. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, INTELLIGENT TRUSS 26" x 30" SPIGOTS (optional) MAXIMUM ALLOWABLE UNIFORM LOADS CENTER MAXIMUM ALLOWABLE LOADS THIRD QUARTER No. of 10' Sections Span ft. (mtrs) #/ft (2.44) (4.88) (7.32) (9.75) (12.19) (14.63) (17.07) (3048) (2968) (2896) (2816) (2740) (2417) (1930) (3051) (2974) (2776) (2015) (1543) (1215) (970) (1525) (1487) (1448) (1410) (1157) (911) (728) (1017) (991) (966) (940) (772) (608) (485) Note: Deflections reported in the above tables are maximum expected for full loadings (indoors only). All loads are based on 8'-0" sections. tables are reprinted from engineering reports developed by Parkhill, Smith & Cooper, Inc., structural engineers, and apply to truss fabricated after December, INTELLIGENT TRUSS 26" x 30" End plates equipped for bolts or optional spigots. Spigots Only Item Code Weight Item Code Weight 93" INTELLIGENT TRUSS 96"INTELLIGENT TRUSS TRS 26IT-093B TRS 26IT-096S 159 (72) 186 (84) HANDLE TRS 26IT-HAND 2 (.9) 123" INTELLIGENT TRUSS 126" INTELLIGENT TRUSS TRS 26IT-123B TRS 26IT-126S 184 (83) 210 (94) BUNGIED FIXTURE RESTRAINTS TRS 26IT-NET.5 (.23) UNIVERSAL FIXTURE MOUNTING BRACKETS (Set of 2) TRS 26IT-BIO 4 (1.8) Empty truss includes headframe, universal fixture mounting brackets, and bungied restraints. * (See catalog pages T-5/6 for spigoted accessories and catalog pages T-7/8 for plated accessories.) T-50 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

59 STAGING, LIGHTING AND SUPPORT SYSTEMS 12" Tower Configuration Tower Components 6" 44"/56" Style Mark I Tower Mark II Tower Mark III 12"-Tower 31" 12" 6" Base Connections Bolts Bolts Spigots Head Block Top Tower - 10' MK2 Mid Tower -5', 10' Hinge Radius Head Pin Outrigger Stabilizer 67.5" 12" 95" 20" 12" GROUND SUPPORT SYSTEM 12" GROUND SUPPORT SYSTEM COMPONENTS Connections are singlesets of bolts or Camlocs MK-1 tower is standard MK-1 & MK-2 Tower Components 3' MK1 12" x 12" TOWER 5' MK1 12" x 12" TOWER 8' MK1 12" x 12" TOWER 10' MK1 12" x 12" TOWER 3' MK2 12" x 12" TOWER 5' MK2 12" x 12" TOWER 8' MK2 12" x 12" TOWER 10' MK2 12" x 12" TOWER 44" HINGE BLOCK FOR 12" TOWER (for use with MD & PRT Trusses) 56" HINGE BLOCK FOR 12" TOWER (for use with HD Trusses) BASE FOR 12" X 12" TOWER OUTRIGGER/STABILIZER SET PER TOWER For use with 44" Hinge Block For use with 56" Hinge Block HEAD BLOCK FOR 12" x 12" TOWER* For use with 2020, 2630, 3020 RADIUS HEAD 3/4" CLEVIS PIN 5/8" GRADE-8 BOLT, NUT & WASHERS Item Code Bolt TRS 12G1-036B Cam TRS 12G1-036C Bolt TRS 12G1-060B Cam TRS 12G1-060C Bolt TRS 12G1-096B Cam TRS 12G1-096C Bolt TRS 12G1-120B Cam TRS 12G1-120C Bolt TRS 12G2-036B Cam TRS 12G2-036C Bolt TRS 12G2-060B Cam TRS 12G2-060C Bolt TRS 12G2-096B Cam TRS 12G2-096C Bolt TRS 12G2-120B Cam TRS 12G2-120C Bolt TRS 12GS-H44B Cam TRS 12GS-H44C Bolt TRS 12GS-H56B Cam TRS 12GS-H56C Bolt TRS 12GS-BB Cam TRS 12GS-BC TRS 12GS-OS44 TRS 12GS-OS56 Bolt TRS 12GS-HBB Cam TRS 12GS-HBC HDW CP-75R BLT BOLT SET Weight 26 (13) 40 (18) 58 (27) 69 (31) 34 (15) 49 (22) 71 (32) 87 (39) 61 (27) 67 (30) 46 (21) 101 (46) 103 (47) 41 (18) MK-3 Tower Components Item Code Weight MK-3 Tower Components (con t) Item Code Weight 3' MK3 12" x 12" TOWER Spig TRS 12G3-036S 29 (13) BASE FOR 12" X 12" TOWER Spig TRS 12G3-BS 46 (21) 5' MK3 12" x 12" TOWER 8' MK3 12" x 12" TOWER 10' MK3 12" x 12" TOWER 44" HINGE BLOCK FOR 12" TOWER (for use with MD & PRT Trusses) 56" HINGE BLOCK FOR 12" TOWER (for use with HD Trusses) Spig TRS 12G3-060S Spig TRS 12G3-096S Spig TRS 12G3-120S Spig TRS 12G3-H44S Spig TRS 12G3-H56S 40 (18) 58 (27) 69 (31) 61 (27) 67 (30) OUTRIGGER/STABILIZER SET PER TOWER For use with 44" Hinge Block For use with 56" Hinge Block HEAD BLOCK FOR 12" x 12" TOWER* For use with 2020, 2630, 3020 RADIUS HEAD 3/4" CLEVIS PIN * Standard for GS 5/16" chain TRS 12G3-OS44 TRS 12G3-OS56 Spig TRS 12G3-HBB HDW CP-75R 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) (46) 103 (47) 41 (18) T-51

60 STAGING, LIGHTING AND SUPPORT SYSTEMS 16" Ground Suppport Tower Components 37" 6" Head Block 16" GROUND SUPPORT SYSTEM 16" GROUND SUPPORT SYSTEM COMPONENTS Connections are steel spigots & 3/4" clevis pin 10' 16"x16" TOWER TOP SECTION 20' 16"x16" TOWER TOP SECTION 5' 16"X16" TOWER Item Code Bolt TRS 16G1-120B Cam TRS 16G1-120C Bolt TRS 16G1-240B Cam TRS 16G1-240C TRS 16G1-060S Weight 116 (53) 191 (87) 63 (29) Top Tower - 10', 20' 10' 16"X16" TOWER TRS 16G1-120S 101 (46) 20' 16"X16" TOWER TRS 16G1-240S 176 (80) 5' HINGE BLOCK FOR 16" x 16" TOWER (for use with HDPRT Trusses) Bolt TRS 16G1-H60B Cam TRS 16G1-H60C 109 (50) BASE FOR 16" x 16" TOWER Bolt TRS 16G1-BB Cam TRS 16G1-BC 69 (31) 16" Spigot Radius Pin OUTRIGGER/STABILIZER SET PER TOWER HEAD BLOCK FOR 16" x 16" TOWER* (for use with HDPRT Trusses) TRS 16G1-OS60 Bolt TRS 16G1-HBB Cam TRS 16G1-HBC 151 (68) 50 (23) 3/4" CLEVIS PIN HDW CP /8" 6" Base Mid Tower - 5', 10' Spigot Radius Pin Hinge 5' Radius Head Pin Stabilizer Outrigger 77.75" 16" 110" 24" RADIUS HEAD 3/4" CLEVIS PIN 5/8" GRADE-8 BOLT, NUT & WASHERS HDW CP-75R BLT BOLT SET NOTE: 16" Towers used with BFT Roof are not part listed here, but are part of kit. Head Blocks, Stabilizer & Hinge Block are also custom to kit. * Standard for GS 5/16" chain Designed to raise TOMCAT truss using Columbus McKinnon Theatrical Chain Hoists (Headblock sheaves for 5/16" chain is standard, but 1/4" chain sheaves are available). Standard sleeve blocks are available for midsize to large types of TOMCAT truss. All hinge and spigot connections employ 3/4" radius head pins. *Towers are designed to support both axial and flexural (Bending) loads simultaneously. Axial load capacity is dependent upon the amount of flexural loading placed upon the structure through a number of sources including, but not limited to the eccentric axial loads, moment transfer from horizontal truss loading (via sleeve and corner blocks), wind forces and seismic forces. Due to the Profile size (square) Indoor Use Outdoor Use Bolt Connection Camloc Connection Spigot Connection imum Height. Axial *. Flexural * Mark I Mark II Mark III 16" Tower 12" (30.5 cm) Yes No Available Available No 35' (10.67 m) 2,000lbs (907kg) 3.63 K-ft. 12" (30.5 cm) Yes Yes Available Available No 35' (10.67 m) 3,000lbs (1361kg) 3.63 K-ft. 12" (30.5 cm) Yes Yes No No Yes 35' (10.67 m) 3,000lbs (1,360kg) K-ft. 16" (40.6 cm) Yes Yes No No Yes 45' (13.72 m) 4,000lbs (1,815kg) K-ft. interdependent nature of the two forces, the loads stated above should be used for reference only and as either of the variables change along their respective planes, allowable loads may increase or decrease as a result. Axial loads are represented in the table above in both pounds and kilograms. Flexural loads are represented in kip feet. Dynamic loads must be converted into a static load equivalent for comparison to the rated capacity. All towers for use outdoors must be checked for flexural loads introduced by wind loading on the towers and related structures. Contact your TOMCAT representative for further assistance and other information on the specific use of towers in your situation. T-52 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

61 STAGING, LIGHTING AND SUPPORT SYSTEMS SPOT CHAIRS Top View Top Mount Spot Chair 33" (83.82) 30" (76.2) 12 3/8" (31.43) Top or Universal mount Seat belt provided Removable 15-3/4" x 20-3/4" Ballast Tray Spot Mount provided Swivel couplers available separately Universal spot chair has removable halo section 45 1/2" (115.57) Universal Mount Spot Chair SPOT CHAIRS Follow Spot Chairs - includes seat belt, removable ballast tray, and spot mount. Does not include swivel couplers to mount chair to trussing. Specify Spot Type when ordering. 9 7/8" (25.08) 2 3/8" (40.64) 7 3/8" (121.92) TOP MOUNT SPOT CHAIR UNIVERSAL MOUNT SPOT CHAIR * Approximate weight Item Code TRS ACC-SCTOP TRS ACC-SCUNI 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) Weight *23 (10) *51 (23) T-53

62 STAGING, LIGHTING AND SUPPORT SYSTEMS SPECIAL ASSEMBLIES Custom Circular Truss Application Made From: 12"x12" Light Duty Box Truss 20.5"x20.5" Medium Duty Box Truss 20.5"x30" Heavy Duty Box Truss Ladder Truss Roll Drops Sound Delay Tower Custom Speaker Support Grid T-54 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

63 STAGING, LIGHTING AND SUPPORT SYSTEMS PRT SUNSHADE ROOF SYSTEM PRT PEAKED SUNSHADE Long demanded by the touring industry, the Pre-Rigged Truss (PRT) Sunshade has quickly become the favorite system for small to medium sized productions. Designed for rapid disassembly and mobility, the PRT Sunshade may be utilized in a variety of venues. More importantly, the system is built from industry standard components like 93" Double Hung Pre-Rigged Truss (see catalog pg. T-7) and Mark I Towers (see catalog pg. T-51) adding to its versatility. Two options are available. The Peaked Sunshade (shown above) is patterned after our BFT where the cross stage runs of truss are sloped approximately 5% to form a peak in the center. A canopy is attached to the components of the main body. The Flat Sunshade (shown below) incorporates a canopy rail system above a flat Pre-Rigged Truss grid to form the roof s pitch. Both options are available with PA Wings formed with a 123" section of Double-Hung Pre- Rigged Truss used to connect each downstage tower to an additional tower. The live loads (equipment loads) that can be applied to the system include a 6,000 pound uniformly distributed load (UDL) on the main grid and a 5,000 pound speaker load on each PA Wing - making it ideal for many applications. 26'-6" 28'-8" 33'-11 7/8" 34'-5 7/8"" 29'-3 7/8" 31'-5 7/8" 34'-1 15/16" PRT FLAT SUNSHADE 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) S-1

64 STAGING, LIGHTING AND SUPPORT SYSTEMS PRT SUNSHADE ROOF SYSTEM PRT PEAKED SUNSHADE 43' /2" 43' - 9 3/4" 18' - 1 7/8" 18' - 1 7/8" PRT FLAT SUNSHADE 43' /2" 20' - 8 1/4" 43' - 9 3/4" 32' /16" 3' /16" 18' - 1 7/8" 18' - 1 7/8" 43' - 9 3/4" 29' - 3 7/8" 34' /16" 12' /8" 12' /8" 69' - 6" Plan End Elevation 64' - 6" Plan End Elevation S-2 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

65 46' x 43' ROOF 41' 41 ' 28'-10" This roof design has long been one of the most popular ever offered by TOMCAT due to it s loading capabilities and it s ease of transportation. Because of it s unique construction, including sleeves for the 12-inch tower that are built into the perimeter grid, the system boasts a total maximum uniform distributed load of 16,000-pounds (7,258kg). The name of this roof is derived from the outside dimensions of the grid: 43' (13.11m) deep by 46' (14.02m) wide. In addition to the ability to erect the system in just a few hours, the entire system fits easily into a mid-size truck. The system is shown here without the guy wires that are required for outdoor installations. 35'-7" STAGING, LIGHTING AND SUPPORT SYSTEMS 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) S-3

66 46' x 43' ROOF STAGING, LIGHTING AND SUPPORT SYSTEMS Roof Grid will support 16,000 lbs. Roof Cover provided. Entire System will pack into 24' truck. Roof lifts with four CM chain hoists. Guy package required for outdoor use. Detailed Engineering information available on request. Side Elevation Front Elevation Plan View S-4 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

67 64' x 40' ROOF with PA WINGS STAGING, LIGHTING AND SUPPORT SYSTEMS 41'-6" ND OU GR L E LEV 35'-9" OU GR ND LEV EL 5 5 '-0 1 /8 " " '-5 " 60 ' Standing for Big Frame Truss, this roof design is true to it s name as it features 26" x 36" cross-stage truss, 26" x 43" end truss and folding 26" triangle truss as the up-stage/downstage part of the grid. The system utilizes 16" x 16" towers. The general dimensions of the BFT are 60' x 40' (18.29m x 12.19m), not including the optional PA wings that are shown here. The maximum uniformly distributed load capacity for the BFT is 60,000-pounds (27,215kg). Like most TOMCAT roof systems, the BFT can, and has been customized to a variety of other dimensions to fit a customer s specific needs. The system is depicted here without the guy wires for use outdoors. 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) S-5

68 STAGING, LIGHTING AND SUPPORT SYSTEMS 64' x 40' ROOF with PA WINGS Tower Plan View PA Wing Capacity U.D.L. 20,000 Lbs. Front View Main Roof Capacity U.D.L. 60,000 Lbs. PA Wing Capacity U.D.L. 20,000 Lbs. Plan View S-6 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

69 KT-7 ROOF STAGING, LIGHTING AND SUPPORT SYSTEMS * shown without PA wings 49'-10" GRO UND LEVE L 43' '-7" '-5" 160 EL '- ND 1 2" 1/ Raised on 22-1/2" towers, this roof system provides customers with an unobstructed opening of over 100' (30.48m) and a depth of 60' (18.28m). The grid is made up of folding 31" x 54" truss with truss ladders providing the up-stage/down-stage part of the grid, thus providing for the maximizing of shipping space. The maximum uniformly distributed load for the KT system as shown is 100,000pounds (45,360kg). The system is shown here with a roof peak incorporated into the design, but is available in a flat configuration to meet the specific needs of customers. It is also shown without the required guy wires for outdoor applications. OU GR LEV 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) S-7

70 KT-7 ROOF STAGING, LIGHTING AND SUPPORT SYSTEMS Front View Plan View S-8 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

71 45' x 45' LADDER ROOF STAGING, LIGHTING AND SUPPORT SYSTEMS This is the newest of the TOMCAT roof systems and is designed to meet customer demands for economy in terms of shipping space without sacrificing its loading capabilities. Constructed with an optional perimeter of folding 20.5" x 30" truss, it uses a system of single truss ladders to form the internal grid. The ladders are joined by TOMCAT s own unique intersection spigot connection. The use of the folding box truss along with the ladder grid allows for compact shipping and storage, but because of the unique design it still provides for a maximum uniformly distributed load of 16,000-pounds (7,257 kg). 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) S-9

72 STAGING, LIGHTING AND SUPPORT SYSTEMS 45' x 45' LADDER ROOF Plan View Front View Side View S-10 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

73 STAGING, LIGHTING AND SUPPORT SYSTEMS 65' x 45' LADDER ROOF With PA Wings Without PA Wings This is the newest of the TOMCAT roof systems and is designed to meet customer demands for economy in terms of shipping space without sacrificing its loading capabilities. Constructed with an optional perimeter of folding 20.5" x 30" truss, it uses a system of single truss ladders to form the internal grid. The ladders are joined by TOMCAT s own unique intersection spigot connection. The use of the folding box truss along with the ladder grid allows for compact shipping and storage, but because of the unique design it still provides for a maximum uniformly distributed load of 20,000-pounds (9,072 kg). Available in smaller configurations, the 60' x 40' (18.28m x 12.19m) is shown here without the rafters for the canvas nor the guy wires required for outdoor use. 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) S-11

74 STAGING, LIGHTING AND SUPPORT SYSTEMS 65' x 45' LADDER ROOF Front View Plan View S-12 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

75 SPECIAL ROOFS STAGING, LIGHTING AND SUPPORT SYSTEMS SEA WORLD - Orlando, Florida 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) S-13

76 SPECIAL ROOFS STAGING, LIGHTING AND SUPPORT SYSTEMS SHIMIZU - Tokyo S-14 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

77 STAGING, LIGHTING AND SUPPORT SYSTEMS MOTORS and CONTROL Lodestar motors are designed specifically for the entertainment industry and are custom prepped to customers specifications by TOMCAT. By maintaining a stock of most hoist sizes along with the chain and other parts, TOMCAT is able to respond to customers demands for the finest hoists, faster than anyone. Each Lodestar chain hoist comes in a standard black matte finish in either single phase or three phase models. Swivel hook suspensions are standard and latch-lock hooks are available for all models. To meet the requirements of the entertainment industry, each hoist is specifically designed to operate in the inverted position. It is preferred that the load always be tied off with auxiliary chains or cables before access to the area beneath the load is permitted. As an alternative, the system may be designed such that malfunction or failure of one hoist s load bearing components does not cause load loss and/or overloading of any other hoist(s) in the system. Not that in such a system, hoist performance and function must be monitored visually or with the use of load cells. Both load cell and speed sensor kits are available options on all Lodestar hoists supplied by TOMCAT. MODEL F & C MODEL L, LL, J & JJ MODEL R & RR! WARNING Improper use of Lodestar motors can result in bodily injury or property damage. To avoid injury or damage: Do not use Lodestar motors to lift people. 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) M-1

78 STAGING, LIGHTING AND SUPPORT SYSTEMS MOTORS and CONTROL MODEL SPECIFICATIONS: Size & Capacity Capacity: Tons (Kg) Speed Motor Horspower Body Weight: Ibs (kg) Electric Standard Single Phase Voltage Current (AMPS) 115/1/60 Standard 3 Phase Voltage Current (AMPS) 230/3/60 Standard 3 Phase High Voltage Current (AMPS) 460/3/ 60 Chain Chain Weight: IbsNt (kg/m) Chain Length plus fl (m) Standard lift limit: ft (m) C 1/4 (250) 32 FPM 1/2 75 (34) (.74) 1 x Lift 2.5 (.76) 204 (62.2) F 1/2 (500) 16 FPM 1/2 74 (33.6) (.74) 1 x Lift 2.5(.76) 102(31.1) J 1/2 (500) 32 FPM (52.2) (1.49) 1 x Lift 2.5(7.6) 125 (38.1) JJ 1/2 (500) 64 FPM (54.4) (1.49) 1 x Lift 2.5(.76) 254 (77.4) L 1 (1,000) 16 FPM (51.7) (1.49) 1 x Lift 2.5(.76) 125 (38.1) R 2 (2,000) 8 FPM (60.8) (1.49) 2xLift 5(1.5) 66 (20.1) RR 2 (2,000) 16 FPM (61.7) (1.49) 2xLift 5 (1.5) 125 (38.1) ITEM CODES: Single Phase Hoist Three Phase Hoist Chain Motor Prep No Connectors Single Phase Hubbell 5266C - Power Hubbell Control Three Phase Hubbell Power Hubbell Control High Voltage Prep Code Pickles With Hubbell 2411 No Hubbell Chain Bags Small Frame Strap-On Small Cloth Bucket Large Cloth Bucket Large Frame Strap-On XL Cloth Bucket Latchlock Hooks (Exchange) Upper Lower Hoist Handles Installed MTR C1PH MTR C3PH MTR LC1/4 MTR PREP MTR PREP1 PH MTR PREP3PH MTR PREPHV MTR PICHUB MTR PIC RIG CBSMS RIG CBSMB RIG CBLGB - - MTR CM1050 MTR CM MTR F1PH MTR F3PH MTR LC1/4 MTR PREP MTR PREP1PH MTR PREP3PH MTR PREPHV MTR PICHUB MTR PIC RiG CBSMS RIG CBSMB RIG CBLGB - - MTR CM1050 MTR CM MTR J1PH MTR J3PH MTR LC5/16 MTR PREP MTR PREP1PH MTR PREP3PH MTR PREPHV MTR PICHUB MTR PIC - RIG CBSMB RIG CBLGB RIG CBLMS RIG CBXLB MTR CM1054 MTR CM1051 MTR HAND-1 - MTR JJ3PH MTR LC5/16 MTR PREP - MTR PREP3PH MTR PREPHV MTR PICHUB MTR PIC - RIG CBSMB RIG CBLGB RIG CBLMS RIG CBXLB MTR CM1054 MTR CM1051 MTR HAND-1 MTR L1 PH MTR L3PH MTR LC5/16 MTR PREP MTR PREP1PH MTR PREP3PH MTR PREPHV MTR PICHUB MTR PIC - RIG CBSMB RIG CBLGB RIG CBLMS RIG CBXLB MTR CM1054 MTR CM1051 MTR HAND-1 MTR R1 PH MTR R3PH MTR LC5/16 MTR PREP MTR PREP1PH MTR PREP3PH MTR PREPHV MTR PICHUB MTR PIC - RIG CBSMB RIG CBLGB RIG CBLMS RIG CBXLB MTR CM1056 MTR CM1057 MTR HAND-1 - MTR RR3PH MTR LC5/16 MTR PREP - MTR PREP3PH MTR PREPHV MTR PICHUB MTR PIC - RIG CBSMB RIG CBLGB RIG CBLMS RIG CBXLB MTR CM1056 MTR CM1057 MTR HAND-1 M-2 USA - Tel: (915) Fax: (915) UK - Tel: Fax: /97

79 STAGING, LIGHTING AND SUPPORT SYSTEMS MOTORS and CONTROL The PROSTAR Compact Lightweight Durable 300 pound or 600 pound capacity Tomcat Standard 3ø Hubbell Connector Layout All hoists, cabling and controllers available with alternate connectors Single Phase Hoist Power / Control Cables P Power Hubbells C & 5269C (Edison) C Control Hubbells & 2411 Base Code for Hubbells & assembly Up to 100' - power 12/3 SJO & control 16/4 SO Cable charge per foot ItemCode ELE MC1PH ELE MC12/3 P CM 3ø MOTOR C Three Phase Hoist Power / Control Cables P Power Hubbells & 2433 C Control Hubbells & 2411 ItemCode Base Code for Hubbells & assembly ELE MC3PH HOIST & CABLE ASSY. POWER & CONTROL Up to 100' - power 16/4 SO & control 16/4 SO Cable charge per foot ELE MC16/ C P Up to 150' - power 14/4 SJO & control 16/4 SO Cable charge per foot Up to 150' - power 12/4 SJO & control 16/4 SO Cable charge per foot ELE MC14/4 ELE MC12/4 10/4 SO ' 16/4: 16/4 cable assembly 100' 16/4: 16/4 cable assembly ELE MC3PH50 ELE MC3PH100 CS 8364C /4 SO CS 2723 CS-800 CS-400 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) M-3

80 STAGING, LIGHTING AND SUPPORT SYSTEMS MOTORS and CONTROL CS800 MOTION CONTROLS The CS-800 controller provides power distribution and relay control to run up to eight hoists from a single compact unit. It is available in a variety of formats to meet individual needs. MTR SKCS-8OO For use with volt, 3 phase hoists. It uses 50 amp, 250 volt Hubbell connector for input power, a 20 amp 480 volt Hubbell connector for output power and a 20 amp 125/250 volt Hubbell connector for control. Features include safety key on/off switch with phase reversal and phase power indicators. It comes standard with full function remote which allows both up and down operation of any or all of the hoists. The remote is hard-wired to a 50 cable which plugs into the controller. Dimensions: in (42.5 cm) wide x 21-in (53.3 cm) deep x 7.13-in (18.1 cm) deep, 39 lbs (17.7 kg). MTR SKCS-8OO (Specify Rack Mount) Same as above, with additional feature of a rack-ear case that is required if unit is to be mounted in a road case. Dimensions: 19-in (48.3 cm) wide x 21-in (53.3 cm) high x 6.5-in (16.5 cm) deep, 39 lbs (17.7 kg). CS800R MTR SKCS-8OOHV For use with volt, 3 phase hoists. It uses a 50 amp, 480 volt Hubbell connector for input power, a 20 amp, 480 volt Hubbell connector for output power and a 20 amp 125/250 volt Hubbell connector for control. Features include safety key on/off phase reversal switch with phase power indicators. It comes standard with full function remote which allows both up and down operation of any or all of the hoists. The remote is hard-wired to a 50 cable which plugs into the controller. Dimensions: in (42.5 cm) wide x in (57.8 cm) high x 7.13-in (18.1 cm) deep, 55 lbs (24.9 kg). MTR SKCS-8OOHV (Specify Rack Mount) Same as above, with additional feature of a rack-ear case that is required if unit is to be mounted in a road case. Dimensions: 19-in (48.3 cm) wide x in (57.8 cm) high x 6.5-in (16.5 cm) deep, 55 lbs (24.9 kg). MTR SKCS-8OOEC For use with volt, 3 phase hoists. It uses Cee Form connectors for both input power and output power and control, and features safety key on/off phase reversal switch and phase power indicators. It comes standard with full function remote which allows both up and down operation of any or all of the hoists. The remote is hard-wired to a 50 cable which plugs into the controller. Dimensions: in (42.5 cm) wide x 24.5-in (62.23 cm) high x 7.13-in (18.1 cm) deep, 55 lbs (24.9 kg). MTR SKCS-8OOEC (Specify Rack Mount) Same as above, with additional feature of a rack-ear case that is required if unit is to be mounted in a road case. Dimensions: 19-in (48.3 cm) wide x 24.5-in (62.23 cm) high x 6.5-in (16.5 cm) deep, 55 lbs (24.9 kg). M-4 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

81 STAGING, LIGHTING AND SUPPORT SYSTEMS MOTORS and CONTROL CS400 MOTION CONTROLS The CS-400 controller provides power distribution and relay control to run up to four hoists from a single compact unit. It is available in a variety of formats to meet individual needs. MTR SKCS-4OO For use with volt, 3 phase hoists. It uses 30 amp, 250 volt Hubbell connector for input power, a 20 amp, 480 volt Hubbell connector for output power and and a 20 amp, 250 volt Hubbell connector for control. Features include safety key on/off phase reversal switch with phase power indicators. It comes with a run only remote on a 25 cable. Dimensions: 17-in (43.2 cm) wide x 14-in (35.6 cm) hign x 6-in (15.2 cm) deep 35 lbs (15.9 kg) MTR SKCS-4OO (Specify Rack Mount) Same as above, with the additional feature of a rack-ear case that is required if unit is to be mounted in a road case. Dimensions: 19-in (48.3 cm) wide x 14-in (35.6 cm) high x 6-in (15.2 cm) deep, 35 lbs (15.9 kg) CS400RM MTR SKCS-4OOR For use with volt, 3 phase hoists. It uses 30 amp, 250 volt Hubbell connector for input power a 20 amp, 480 volt Hubbell connector for output power and a 20 amp 125/250 volt Hubbell connector for control. Features include safety key on/off phase reversal switch and phase power indicators. It comes standard with full function remote which allows both up and down operation of any or all of the hoists. The remote is hard-wired to a 25 cable which plugs into the controller. Dimensions: 17-in (43.2 cm) wide x 14-in (35.6 cm) high x 6-in (15.2 cm) deep, 35 lbs (15.9 kg) MTR SKCS-4OOR (Specify Rack Mount) Same as above, with the additional feature of a rack-ear case that is required if unit is to be mounted in a road case. Dimensions: 19-in (48.3 cm) wide x 14-in (35.6 cm) high x 6-in (15.2 cm) deep, 35 lbs (15.9 kg) MTR SKCS-4OORHV For use with volt, 3 phase hoists. It uses a 20 amp, 480 volt Hubbell connector for input power, a 20 amp, 480 volt Hubbell connector for output power and a 20 amp, 125/250 volt Hubbell connector for control. It features safety key on/off phase reversal switch and phase power indicators. It comes standard with full function remote which allows both up and down operation of any or all of the hoists. The remote is hard-wired to a 25 cable which plugs into the controller. Dimensions: 17-in (43.2 cm) wide x 15.8-in (40 cm) highx 6-in (15.2 cm) deep, 43 lbs (19.5 kg) MTR SKCS-4OORHV (Specify Rack Mount) Same as above, with the additional feature of a rack-ear case that is required if unit is to be mounted in a road case. Dimensions: 19-in (48.3 cm) wide x 15.8-in (40 cm) high x 6-in (15.2c m) deep, 43 lbs (19.5 kg) MTR SKCS-4OO-EC For use with volt, 3 phase hoists. It uses Cee Form connectors for both input power and output power and control, and features safety key on/off switch, phase reversal switch, phase power indicators. It comes standard with full function remote which allows both up and down operation of any or all of the hoists. The remote is hard-wired to a 25 cable which plugs into the controller. Dimensions: 17-in (43.2 cm) wide x 15.8-in (40 cm) high x 6-in (15.2 cm) deep, 43 lbs (19.5 kg) MTR SKCS-4OO-EC (Specify Rack Mount) Same as above, with the additional feature of a rack-ear case that is required if unit is to be mounted in a road case. Dimensions: 19-in (48.3 cm) wide x 15.8-in (40 cm) high x 6-in (15.2 cm) deep, 43 lbs (19.5 kg) 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) M-5

82 STAGING, LIGHTING AND SUPPORT SYSTEMS MOTORS and CONTROL Road Cases for Skjonberg Controllers - Each includes storage area for remote and castors. MTR SKCASE/CS-400 Road case for 400 series controllers with rack ear cases. Dimensions: 20.8-in (52.7 cm) wide x 23.5-in (59.7 cm) high x 16.5-in (41.9 cm) deep, 45 lbs (20.4 kg). MTR SKCASE/CS-800 Road case for MTR CS8OORM. Dimensions: 20.8-in (52.7 cm) wide x 30.5-in (77.5 cm) high x 16.5-in (41.9 cm) deep, 57 lbs (25.8 kg). MTR SKCASE/CS-800 Road case for MTR CS8OORHVM. Dimensions: 20.8-in (52.7 cm) wide x 34-in (86.4 cm) high x 16.5-in (41.9 cm) deep, 60 lbs (27.2 kg). MTR SKCASE/CS-800 Road case for MTR CS8OORECM. Dimensions: 20.8-in (52.7 cm) wide x 34-in (86.4 cm) high x 16.5-in (41.9 cm) deep, 60 lbs (27.2 kg). Remote Controls and Cables 400 Series (Run Only) MTR SKP4-CS-SQ-A25 MTR SKRXTJ21K025 Run only remote control with 25-foot cable. 25-foot extension cable for MTR CS4-RUN. 400R Series (Full Function) MTR SKP4-CS-SQ-A25 MTR SKP4-CS-SQ-D MTR SKCBLRCTJ21K050 Full function remote hardwired to 25-foot cable. Full function remote with chassis connector. 50-foot extension cablefor full function remote. 800R Series (Slim Line) MTR SKP8-CS-SL-A50 MTR SKP8-CS-SL-D MTR SKCBLRCTJ21K050 MTR SKCBLRCTJ21K100 Slim line remote with hardwired 50-foot cable. Use with all CS800R series controllers. Slim line remote with chassis connector. Requires use of one CS8-C50 control cable, additional extensions may be used. 50-foot extension cable. Has locking ring only on male end. 100-foot extension cable. Has locking ring only on male end. Other Control Options Single phase hoist controllers Custom configurations Computerized hoist controls Hoist sensors Multiple controller systems Cells Custom motion control systems Variable speed controls M-6 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

83 RIGGING STAGING, LIGHTING AND SUPPORT SYSTEMS H BRIDLE BASKET HITCH CHOKER HITCH AUTHORIZED PRODUCTS FOR BETTER LIFTING DISTRIBUTOR 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) R-1

84 RIGGING STAGING, LIGHTING AND SUPPORT SYSTEMS WIRE ROPE SLINGS 3/8" diameter - 5', 10', 20' and 30' in stock 1/2" diameter - 5', 10' and 20' in stock Custom sizes available TOMCAT ROUNDSLINGS 18", 3', 6', 9' and 12' in stock Custom sizes available CM Theatrical Shackles: Designed specifically for the entertainment industry, CM theatrical shackles meet or exceed strength requirements for Federal Specifications RR-C-271. Black phosphated glare resistant finish. Pins and bows stamped with batch lot identification for easy tracing. Each CM theatrical shackle is proof tested at 2.2 times the working load limit Ultimate strength equals 6 times the working load limit. Marked with size and Working Limit (WLL) in tons. Easy pin insertion and removal. Bows forged from micro alloy steel with integral heat treating. Pins forged from 4140 alloy steel and heat treated. Dropped theatrical shackles can be returned to service following visual examination for obvious damage. CM THEATRICAL SHACKLES 1/2", 5/8" and 3/4" in stock RACHET STRAPS made to order CARABINERS BUNGIES 10-1/2" light duty All Diminsions in inches Working W B Tolerance Plus or Approx. CM D P Width L Inside Outside Minus Weight Product Limit Size Diameter Between Inside Width Diameter Per/100 Code (Tons) Diameter Of Pin Eyes Length At Bow Of Eye W L (Lbs.) /2 5/8 13/ /16 1-7/16 1-1/4 1/16 1/ /2 5/8 3/4 1-1/16 2-1/2 1-3/4 1-9/16 1/16 1/ /2 3/4 7/8 1-1/ /8 1/16 1/4 225 Note: Wide range of sizes available. 1.6"-2" ALLOY HALF COUPLER Counterbored hole, Countersunk hole, Straight hole, or no hole SNAPHOOKS and SNAPBRACES 1.9"-2" Standard & Custom Length 1.6"-2" ALLOY SWIVEL COUPLERS Also fixed, parallel or 90 degree HOOK CLAMPS Assorted sizes available Shackles are mechanical couplers which consist of a U shaped body closed by a pin and are used in rigging applications. Exercise the following actions during use to assure safe operation. Inspect shackles before each use for excessive (more than 10% of any original dimension) wear, visable distortion, bending or twisting of more than 10, and damaged or bent load p When applying shackle, do not side load, shock load or overload. Make certain that shackle pin is secure during use. Use only replacement load pins obtained from CM. Other pins may not have the required propreties to sustain the working load. CLEVIS PINS Standard or Radius Head HITCH PINS 5/8" x 4-3/4" 3/4" x 4-3/4" R-CLIPS Small Medium Large BOLT SETS 5/8" x 1-3/4" NON-STANDARD HARDWARE TO ORDER CAMLOCS! WARNING Improper use or care of shackles can result in bodily injury or property damage. To avoid injury or damage: Do not use exceed working load limit. Do not shock or impact load. Do not side load - center line of load must coincide with center line of shackle. Do not replace pin or bolt with other than original equipment parts. Inspect before use for wear, deformation and pin engagement. R-2 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

85 RIGGING STAGING, LIGHTING AND SUPPORT SYSTEMS ItemCode ItemCode 3/8" WIRE ROPE SLINGS by LiftAll Rated capacities lbs vert, 2200 lbs choker, 5800 lbs basket 5' Red RIG SL3/8X5 10' White RIG SL3/8X10 20' Blue RIG SL3/8X20 30' Green RIG SL3/8X30 CASTERS, WHEELS and ACCESSORIES Blue swivel caster Caster plate Mounting hardware for one caster Blue wheel for sleeve block Nylon wheel for sleeve block HDW 4SWCA HDW CASTERPL HDW 4BLWH HDW 4NYW 1/2" WIRE ROPE SLINGS by LiftAll Rated capacities lbs vert, 3800 lbs choker, 10,20 0 lbs basket 5' Red RIG SL1/2X5 10' White RIG SL1/2X10 20' Blue RIG SL1/2X20 TUFLEX EN-60 ROUNDSLINGS Black TOMCAT spansets by LiftAll Rated capacities lbs vert, 4200 lbs choker, 10,600 lbs basket 1.5' RIG EN ' RIG EN60-3 6' RIG EN60-6 9' RIG EN ' RIG EN60-12 CM THEATRICAL SHACKLES Black phosphate finish 1/2" 3 ton WLL RIG SH1/2 5/8" 4.5 ton WLL RIG SH5/8 3/4" 6.5 ton WLL RIG SH3/4 CARABINERS OUTRIGGER / STABILIZER HARDWARE 12" tower base pin - 1 x 6.5" HDW SPPIN6.5 16" tower base pin - 1 x 8.5" HDW SPPIN8.5 Screw jack HDW SJ-10 Screw jack foot HDW SJ-FT Foot attachment screw BLT 5/16X3/4FAH TOMCAT SMALL BUNGIE CORDS BURLAP BAG COUPLERS FOR 2" OD TUBE and MOUNTING BOLTS Half coupler - no mounting hole Half coupler - counterbored hole Half coupler - countersunk 3/8" hole Half coupler - countersunk 1/2" hole RIG BUNGIE RIG BURLAP HDW HCNH HDW HCCB HDW HCCS3/8 HDW HCCS1/2 1" Magic bolt BLT 1MB-N 3" Magic bolt BLT 3MB-N 3/8" x 1-1/4" countersunk bolt and nyloc BLT CS3/8N 1/2 x 1-1/4" countersunk bolt and nyloc BLT CS1/2N Oval carabiner Autolock D carabiner RIGGING KIT RIG BIN-O RIG BIN-DA Eye Bolt w/hex Nut & Roll Pin Eye Bolt w/wing Nut & Roll Pin Fixed 90 degree coupler (pinned) Fixed parallel coupler (welded) HDW EYEBSN HDW EYEWN HDW HC90P HDW HCPW 3 bags 10 x 5/8" shackles 5 x 5' 3 x 1/2" shackles 5 x 10' 5 x 20' 2 x 30' 1 x 40' CAMLOCS AND BOLT SETS Male Camloc #2-3/8" plates Male Camloc #4 - for 1/2" plates Male Camloc crosspin Female Camloc Mounting hdw (2.5mm x 25mm, 2 nylocs) Bolt Set - 5/8" x 1-3/4" gr 8, 2 wash & nut CLEVIS PINS and HITCH PINS BLT CAM02 BLT CAM04 BLT CAMCPINS BLT CAMFE BLT CAMHDW BLT BOLTSET 5/8" Clevis pin - for aluminum spigots HDW CP-625 5/8" x 4-1/2" Hitch pin - for folding triangle HDW HP 3/4" Clevis pin - for steel spigots HDW CP-75 3/4" Radiused head clevis pin - for towers HDW CP-75R 1" Clevis pin - for 3" spigots HDW CP-1 Swivel coupler SNAPHOOKS & SNAPBRACES Snapbrace length measured between centers of gripped tubes Snaphook for 2" OD tube Snaphook for 1.90" OD tube HDW HCSW HDW SHK2 HDW SHK1.9 3' Snapbrace for 2" OD tube non-stock add per foot over 3' non-stock HOOK CLAMPS Prices valid on stock only!! Prices include thumbscrews 7" Double hook clamp HDW 7DBL/2HOLE 10" Double hook clamp HDW 10DBL/2HOL 18" Double hook clamp HDW 18DBL/2HOL 24" Double hook clamp HDW 24DBL/2HOL 26" Double hook clamp HDW 26DBL/2HOL 26" Offset double hook clamp HDW 26DBLOFF GUIDE RODS and SLIDERS (does not include small R clip) Guide rod for PRT /2" Guide rod for HDPRT /2" Guide rod slider - not including bolt HDW GROD25.5 HDW GROD29.5 HDW GROD-SL R - clips Small R-clip - for guide rods Medium R-clip - for 5/8" & 3/4" pins Large R-clip - for 1" pins HDW RC-SM HDW RC-MED HDW RC-LG 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) R-3

86 RIGGING STAGING, LIGHTING AND SUPPORT SYSTEMS R-4 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

87 RIGGING STAGING, LIGHTING AND SUPPORT SYSTEMS 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) R-5

88 RIGGING STAGING, LIGHTING AND SUPPORT SYSTEMS R-6 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) /99

89 RIGGING STAGING, LIGHTING AND SUPPORT SYSTEMS TYPE B TYPE A 6/99 USA - Tel: +1 (915) UK - Tel: +44 (0) MEX - Tel: +52 (0) R-7