580SN WT. Specifications below apply to both Power Shuttle and Powershift S-Type transmission unless otherwise indicated.

Transcription

1 580SN WT LOADER /BACKHOE TIER 4 INTERIM CERTIFIED ENGINE Model Type Case F5C, Tier 4 Interim Emissions Certified Diesel 4-stroke, turbocharged Cylinders 4 Bore/Stroke 3.90 x 4.33 in (99 x 110 mm) Displacement 207 in 3 (3.4 L) Fuel injection Fuel Fuel filter Air intake Cooling Direct high pressure common rail HPCR Diesel w/ water trap Cross-flow Liquid Engine speeds* RPM Rated speed full load 2200 Low idle High idle no load RPM: Gross Net 97 hp (72 kw) 95 hp (71 kw) Maximum 1400 RPM: Gross 334 lb ft (453 N m) Net 333 lb ft (452 N m) Torque rise at rated speed 45% Radiator: Core type Square wave Core size area 486 in 2 (3145 cm 2 ) Rows of tubes 4 Viscous fan: Style 9 blade viscous suction Diameter 19.6 in (500 mm) Ratio 1.4:1 Water pump style Integral Engine oil pump: Deep sump plate cooler w/ pressurized under-piston nozzles Pump operating angle ratings: Side to side Rated 35 Fore and aft Rated 35 Oil filtration Replaceable, full flow cartridge NOTE: *Engine speeds w/ standard transmission. Meets federal emission regulations. POWERTRAIN Transmission optional: 4F-4R Power Shuttle Synchromesh transmission manual gear shift fully synchronized Transmission standard: Powershift S-Type, 4F-3R fully synchronized POWERTRAIN (cont.) Specifications below apply to both Power Shuttle and Powershift S-Type transmission unless otherwise indicated. Gear ratios Forward / Reverse 1st / nd 3.431/ rd / th / 0.657* Travel speeds Forward Reverse mph (kph) mph (kph) 1st 3.9 (6.3) 4.7 (7.6) 2nd 6.2 (10.0) 7.5 (12.0) 3rd 13.3 (21.4) 16.0 (24.9) 4th 24.1 (38.8) 28.9 (46.6)* NOTE: Travel speeds at 2295 engine RPM w/ 19.5 L x 24.0 tires. *4R not available on Powershift S-Type. Transmission optional: Powershift H-Type, 4F-3R hydraulic clutch shifting w/ auto function Gear ratios Forward / Reverse 1st / nd / rd / th 0.811/ Travel speeds Forward Reverse mph (kph) mph (kph) 1st 3.9 (6.2) 4.7 (7.6) 2nd 6.4 (10.3) 7.7 (12.4) 3rd 13.6 (21.9) 16.3 (26.3) 4th 23.0 (37.0) NOTE: Travel speeds at 2295 engine RPM w/ 21.0 L X 24.0 tires. Torque converter ratio 2.6 Limited slip differential 4WD Front 4WD/rear axle: Differential ratio 2.3/2.5 Planetary hub ratio 6.0/6.4 Total reduction ratio 13.7/16.0 Service brakes: Individually applied, power assisted, hydraulically actuated, maintenance-free, self-adjusting, outboard mounted, wet disc, 2 per side. Disc area 384 in 2 (0.25 m 2 ) Parking brakes Trans Mounted spring-applied hydraulic release SAHR ELECTRICAL Voltage 12 Volts, negative ground Alternator 120 amp Battery 850 cold-cranking amps Opt. batteries (2) 850 cold-cranking amps Power plugs (2) 30 amps total OPERATOR ENVIRONMENT ROPS/FOPS certified protective canopy; Key start; Hydrostatic steering; Vinyl air suspension seat w/ 180 swivel; Seat turn around; Electronic hand and foot throttles; Ergonomic loader control lever w/ push-button activation of differential lock and transmission de-clutch; Backhoe pilot controls; 2 Accessory power plugs 30 amp; Anti-vandalism covers canopy only; Cup holder; Coat hook w/ tether strap cab only; Interior rearview mirror; 3 in (76 mm) retractable seat belt; Storage compartment w/ lid; Left-side storage tray; 900 lb (408 kg) counterweight; Extendahoe ; 4WD. Vehicle Control Module w/ menu driven options and onboard diagnostics: Foot throttle sensitivity; Cold weather idle settings; Maintenance settings. Gauges: Engine water temperature; Converter oil temperature; Fuel; Tachometer/hourmeter; Voltmeter. Warning lights: Air cleaner restriction; Alternator; A/C high pressure; Cold start; Engine oil pressure; Hydraulic oil filter bypass; Parking brake; Rear axle fluid temperature sensing system; Low fuel. Audible alarms w/ diagnostics: Coolant temperature; Engine oil pressure; Parking brake engagement; Shuttle engagement/seat position; Backup alarm. Horn dual switched front and rear OPERATING WEIGHT Configuration SAE Transport: 93 in (2.36 m) bucket, PST, 4WD, 21.0 L x 24.0 rear tires, Extendahoe, 24 HD bucket, flip stabilizer pads, 2-Door ROPS cab, air suspension seat, dual battery, backhoe coupler, auxiliary backhoe hydraulics, comfort steer, no operator: 19,985 lb (9065 kg) Add-on weights: Cab over canopy 0 lb (0 kg) 93 in (2.36 m) Long Lip Bucket: 1,188 lb (539 kg) 24 in (0.61 m) HD Universal: 427 lb (193.5 kg) Page 1 of 7

2 HYDRAULICS Pump: Bosch Rexroth Series 31 Variable Displacement Axial Piston Pump Main relief pressure: Standard Power Lift 3,450 +/- 50 psi (238 +/- 3.5 bar) 3,780 +/- 50 psi (261 +/- 3.5 bar) Filtration: 7 micron, full flow replaceable cartridge on return line, condition indicator light for filter Oil cooler Heavy-duty Loader rated engine RPM: 41 2,340 psi ( bar) Loader control valve w/ pilot or manual backhoe controls: Two or three spool closed center sectional control valve. Single lever manual control for lift and tilt functions. The three spool valve uses a proportional Electro-Hydraulic control for the auxiliary function. The lift lever has a positive hold Float position and a return to-dig feature. Loader auxiliary hydraulics w/ proportional thumb switch w/ detent on loader control handle: 0 to 31.5 gpm (0 to 119 L/min) Backhoe rated engine RPM: 41 3,100 psi ( bar) Manual backhoe control valve: Six or seven monoblock open center control valve. Features Pro-Control which includes custom designed spools for each individual function along w/ swing cushioning valve for zero-wag swing control. Basic control valve has an open center parallel circuit for all functions. Pilot backhoe control valve: Six, seven, or eight spool sectional closed center control valve. Features Pro-Control which includes custom designed spools for each individual function along w/ swing cushioning valve for zero-wag swing control. Basic control valve is closed center, w/ circuits in parallel w/ a postcompensated, flow sharing feature for simultaneous operation of all circuits. Unidirectional auxiliary hydraulics: Unidirectional hydraulic valve is equipped w/ an adjustable LS relief valve to control attachment pressure and a 6 position flow control selector for 6 detented, distinct flow settings. Actuation: Manual backhoe controls cab floor pedal Pilot controls left-hand joystick SERVICE CAPACITY Fuel tank 42.0 gal (159.0 L) Hydraulic system total qt (124.9 L) Transmission total system: 4WD Standard 21.0 qt (19.4 L) 4WD Powershift S-Type 22.0 qt (20.7 L) 4WD Powershift H-Type 19.0 qt (18.0 L) Front axle: 4WD Differential 9.1 qt (8.6 L) 4WD Planetaries 1.1 qt (1.0 L) Rear axle: Differential 19.7 qt (18.6 L) Engine oil w/ filter 14.4 qt (13.6 L) Cooling system: w/ heater 19.0 qt (18.0 L) w/o heater 18.3 qt (17.3 L) Window washer reservoir 3.0 qt (2.8 L) OTHER SPECIFICATIONS Front tires 4WD 12.5/80 x 18.0, 10-ply rating Rear tires 4WD 21.0 L x 24.0, 10-ply rating Loader: Single-lever control for lift and tilt; Positive hold float; Return-to-dig; Automatic selfleveling; In line, reverse linkage; Dual parallel dump cylinders; Clutch disconnect button on loader control and shift levers; Bucket position indicator. Loader bucket sizes: Width Weight Struck Heaped Long Lip Bucket w/ bolt on edge 93 in 1,123 lb 1.1 yd yd 3 (2.36 m) (509 kg) (0.84 m 3 ) (0.99 m 3 ) 4 IN 1 Bucket w/ bolt on edge 93 in 1,628 lb 1.0 yd yd 3 (2.36 m) (738 kg) (0.76 m 3 ) (0.92 m 3 ) Turning diameter*: 4WD engaged: Brakes on 12 ft 0 in (3.65 m) Brakes off 14 ft 11 in (4.54 m) 4WD disengaged: Brakes on 11 ft 3 in (3.43 m) Brakes off 13 ft 6 in (4.11 m) NOTE: *Turning diameter dimensions curb to curb w/ 21.0 L x 24.0 tires and 93 in (2.36 m) general purpose bucket. OTHER SPECIFICATIONS (cont.) Backhoe: Over center design, Fabricated S boom ; Pro-Control System; Dipperstick integrated serrated grip teeth; 17,940 lb ft ( N m) swing torque; Case attachment coupler; Foot-swing w/ 3 lever controls; Wing stabilizers w/ cleated dirt pad. Backhoe bucket sizes: Width Weight Heaped Universal Buckets 12 in 295 lb 3.40 ft 3 (305 mm) (134 kg) (0.10 m 3 ) 18 in 356 lb 5.30 ft 3 (457 mm) (162 kg) (0.15 m 3 ) 24 in 427 lb 7.70 ft 3 (610 mm) (194 kg) (0.22 m 3 ) 30 in 489 lb ft 3 (762 mm) (222 kg) (0.29 m 3 ) 36 in 552 lb ft 3 (914 mm) (251 kg) (0.36 m 3 ) High Capacity Buckets 24 in 447 lb 8.50 ft 3 (610 mm) (203 kg) (0.24 m 3 ) 30 in 502 lb ft 3 (762 mm) (228 kg) (0.30 m 3 ) 580 Super N WT Page 2 of 7

3 J D F A N H E B G C M O L K Line drawings are for illustrative purpose only and may not be exact representation of unit. LOADER DIMENSIONS Long Lip Bucket 4 IN 1 Bucket A. Overall operating height fully raised 13 ft 11 in (4.24 m) 13 ft 10 in (4.22 m) Height to: B. Bucket hinge pin fully raised 11 ft 6 in (3.50 m) 11 ft 6 in (3.50 m) C. Bucket hinge pin at SAE carry in (324 mm) in (324 mm) D. Dump angle at full height E. Dump clearance at full height, 43 dump: Bucket 8 ft 11 in (2.73 m) 9 ft 1 in (2.77 m) Clam open 9 ft 11 in (3.01 m) F. Dump reach at full height, 45 dump from bumper: Bucket 27.0 in (685 mm) 27.0 in (685 mm) Clam open 13.9 in (353 mm) Bucket rollback: Groundline SAE carry Full height Adjustable Adjustable K. Digging depth below grade: Bucket flat 6.1 in (156 mm) 5.9 in (151 mm) Clam open dozing 3.5 in (88 mm) L. Reach from front axle centerline bucket on ground 6 ft 8 in (2.05 m) 6 ft 1 in (1.99 m) Lift capacity to full height calculated values 8,425 lb (3822 kg) 8,025 lb (3640 kg) Breakout force: Lift cylinders 11,450 lb (5093 dan) 11,241 lb (5000 dan) Dump cylinders 10,873 lb (4837 dan) 11,674 lb (5193 dan) Bucket cutting edge width 94.2 in (2.39 m) 93.0 in (2.36 m) Maximum grading angle Maximum clam opening 38.3 in (972 mm) Moldboard height 36.8 in (934 mm) Raising time to full height 3.7 sec 3.7 sec Bucket dumping time 2.0 sec 2.0 sec Lowering time: Power down 2.5 sec 2.5 sec Return-to-dig manual controls/pilot controls 3.6 sec 3.0 sec Clam: Open time 1.3 sec Close time 1.1 sec NOTE: Loader dimensions taken with 4WD, 21.0 L x 24.0 rear tires. 580 Super N WT Page 3 of 7

4 DIMENSIONS Standard Backhoe Extendahoe Retracted Extended M. Overall transport length: Long Lip bucket 23 ft 4 in (7.11 m) 23 ft 4 in (7.11 m) 4 IN 1 bucket 23 ft 1 in (7.04 m) 23 ft 1 in (7.04 m) Overall transport width 8 ft 6 in (2.59 m) 8 ft 6 in (2.59 m) Height 4WD with 21.0 L x 24.0 tires: To top of canopy 8 ft 11 in (2.70 m) 8 ft 11 in (2.70 m) 8 ft 11 in (2.70 m) To top of cab 8 ft 11 in (2.73 m) 8 ft 11 in (2.73 m) 8 ft 11 in (2.73 m) To top of exhaust stack 8 ft 9 in (2.67 m) 8 ft 9 in (2.67 m) 8 ft 9 in (2.67 m) N. Transport 11 ft 1 in (3.37 m) 11 ft 7 in (3.53 m) Ground clearance at backhoe frame 14.8 in (377 mm) 14.8 in (377 mm) 14.8 in (377 mm) Angle of departure Wheel tread: 12.5/80 x in (1.92 m) 75.6 in (1.92 m) 75.6 in (1.92 m) 21.0 L x in (1.77 m) 69.6 in (1.77 m) 69.6 in (1.77 m) Width across tires: 12.5/80 x in (2.24 m) 88.2 in (2.24 m) 88.2 in (2.24 m) 21.0 L x in (2.33 m) 91.8 in (2.33 m) 91.8 in (2.33 m) O. Wheelbase: 21.0 L x in (2.15 m) 84.5 in (2.15 m) 84.5 in (2.15 m) CYLINDERS Bore Diameter Rod Diameter Stroke Closed Length Loader: Lift (2) 3.50 in (88.9 mm) 1.88 in (47.6 mm) in (740.0 mm) in ( mm) Bucket (2) 3.00 in (76.2 mm) 1.50 in (38.1 mm) in (516.5 mm) in (759.5 mm) 4 IN 1 clam (2) 3.00 in (76.2 mm) 1.75 in (44.5 mm) 9.08 in (230.6 mm) in (498.3 mm) Backhoe: Boom 5.00 in (127 mm) 2.50 in (63.5 mm) in (971.6 mm) in ( mm) Dipperstick 4.75 in (120.7 mm) 2.50 in (63.5 mm) in (628.5 mm) in ( mm) Bucket 3.50 in (88.9 mm) 2.50 in (63.5 mm) in (897.9 mm) in ( mm) Extendahoe 3.00 in (76.2 mm) 1.75 in (44.5 mm) in ( mm) in ( mm) Swing (2) 4.00 in (101.6 mm) 2.00 in (50.8 mm) in (292.0 mm) in (620.8 mm) Stabilizer (2) 5.25 in (133.4 mm) 2.50 in (63.5 mm) in (518.1 mm) in (852.7 mm) AXLE RATINGS Front 4WD Rear Maximum static 67,883 lb ( kg) 70,848 lb ( kg) Dynamic operating 47,426 lb ( kg) 49,494 lb ( kg) Static operating 18,969 lb (8604 kg) 19,798 lb (8980 kg) SAE J43 11,773 lb (5340 kg) 15,197 lb (6893 kg) 580 Super N WT Page 4 of 7

5 BACKHOE LIFT CAPACITIES Boom Lift BACKHOE OPERATIONAL DATA Standard Backhoe Extendahoe Retracted Extended Standard Power Lift Standard Power Lift Standard Power Lift Lift Capacity lb (kg) Lift Capacity lb (kg) Lift Capacity lb (kg) Lift Capacity lb (kg) Standard Backhoe Extendahoe Retracted Lift Capacity lb (kg) Lift Capacity lb (kg) +16 ft (4.87 m) 2,115 (959) 2,447 (1110) +14 ft (4.27 m) 3,039 (1378) 3,484 (1580) 2,837 (1287) 3,282 (1489) 2,395 (1086) 2,769 (1256) +12 ft (3.66 m) 3,413 (1548) 3,913 (1775) 3,201 (1452) 3,701 (1679) 2,536 (1151) 2,935 (1331) +10 ft (3.05 m) 3,499 (1587) 4,015 (1821) 3,281 (1488) 3,797 (1722) 2,593 (1176) 3,001 (1361) +8 ft (2.44 m) 3,485 (1581) 4,005 (1817) 3,263 (1480) 3,783 (1716) 2,564 (1163) 2,972 (1348) +6 ft (1.83 m) 3,438 (1559) 3,957 (1795) 3,213 (1457) 3,732 (1693) 2,549 (1156) 2,961 (1343) +4 ft (1.22 m) 3,374 (1530) 3,890 (1764) 3,146 (1427) 3,662 (1661) 2,521 (1144) 2,935 (1331) +2 ft (0.61 m) 3,307 (1500) 3,820 (1733) 3,077 (1396) 3,590 (1628) 2,489 (1129) 2,904 (1317) Ground Level 3,251 (1475) 3,761 (1706) 3,018 (1369) 3,528 (1600) 2,489 (1129) 2,904 (1317) -2 ft (0.61 m) 3,201 (1452) 3,710 (1683) 2,965 (1345) 3,474 (1576) 2,466 (1118) 2,882 (1307) -4 ft (1.22 m) 3,175 (1440) 3,686 (1672) 2,935 (1331) 3,446 (1563) 2,446 (1109) 2,866 (1300) -6 ft (1.83 m) 3,182 (1443) 3,699 (1678) 2,938 (1333) 3,455 (1567) 2,443 (1108) 2,869 (1301) -8 ft (2.44 m) 3,258 (1478) 3,792 (1720) 3,007 (1364) 3,541 (1606) 2,465 (1118) 2,899 (1315) -10 ft (3.05 m) 3,441 (1561) 3,951 (1792) 3,175 (1440) 3,685 (1671) 2,530 (1148) 2,979 (1351) -12 ft (3.66 m) 2,707 (1228) 3,187 (1446) -14 ft (4.27 m) 3,239 (1469) 3,759 (1705) Dipper Lift: +14 ft (4.27 m) 4,281 (1942) 4,281 (1942) +12 ft (3.66 m) 5,822 (2641) 5,822 (2641) 5,618 (2548) 5,618 (2548) 4,046 (1835) 4,046 (1835) +10 ft (3.05 m) 5,600 (2540) 5,600 (2540) 5,399 (2449) 5,399 (2449) 3,984 (1807) 3,984 (1807) +8 ft (2.44 m) 5,562 (2523) 5,562 (2523) 5,360 (2431) 5,360 (2431) 3,913 (1775) 3,913 (1775) +6 ft (1.83 m) 6,236 (2829) 6,236 (2829) 6,030 (2735) 6,030 (2735) 4,166 (1889) 4,166 (1889) +4 ft (1.22 m) 7,424 (3368) 7,424 (3368) 7,203 (3267) 7,203 (3267) 4,102 (1861) 4,102 (1861) +2 ft (0.61 m) 4,850 (2200) 4,850 (2200) NOTE: Boom and Dipper Lift Capacities are rated per SAE J31 and are 87% of the maximum hydraulic lift force available with the specified options. Extended Digging depth: Maximum 14 ft 6 in (4.43 m) 14 ft 6 in (4.43 m) 18 ft 0 in (5.48 m) Maximum with hi-capacity bucket 15 ft 1 in (4.59 m) 15 ft 1 in (4.59 m) 18 ft 6 in (5.64 m) 2 ft (610 mm) flat bottom 14 ft 5 in (4.39 m) 14 ft 5 in (4.39 m) 17 ft 11 in (5.45 m) 8 ft (2.44 m) flat bottom 13 ft 5 in (4.09 m) 13 ft 5 in (4.09 m) 17 ft 1 in (5.22 m) Overall reach from: Rear axle centerline 21 ft 11 in (6.68 m) 21 ft 11 in (6.68 m) 25 ft 4 in (7.71 m) Swing pivot 18 ft 3 in (5.56 m) 18 ft 3 in (5.56 m) 21 ft 8 in (6.60 m) Loading height 12 ft 0 in (3.66 m) 12 ft 0 in (3.66 m) 14 ft 4 in (4.38 m) Loading reach 4 ft 8 in (1.42 m) 4 ft 8 in (1.42 m) 7 ft 3 in (2.22 m) Swing arc Bucket rotation: Mechanical coupler Hydraulic coupler Extendahoe dipper Hydraulic coupler standard dipper Stabilizer spread operating: Flip pad 10 ft 9 in (3.28 m) 10 ft 9 in (3.28 m) 10 ft 9 in (3.28 m) Cast pad 11 ft 1 in (3.38 m) 11 ft 1 in (3.38 m) 11 ft 1 in (3.38 m) Digging force: Bucket cylinder SAE rated 3,460 psi 13,576 lb ( N) 13,576 lb ( N) 13,576 lb ( N) Bucket cylinder Power Lift 14,831 lb ( N) 14,831 lb ( N) 14,831 lb ( N) Dipper cylinder SAE rated 3,460 psi 8,657 lb ( N) 8,657 lb ( N) 6,305 lb ( N) Dipper cylinder Power Lift 9,458 lb ( N) 9,458 lb ( N) 6,888 lb ( N) Leveling angle: Flip pad Cast pad NOTE: Lift capacities apply straight to the rear of prime mover. Equipped with 24 in (610 mm) Universal heavy-duty trenching bucket and Case coupler except as noted. 580 Super N WT Page 5 of 7

6 STANDARD EQUIPMENT OPERATOR ENVIRONMENT See page 1 ENGINE Case F5C Interim Tier 4, with CEGR/DPF after treatment IT4 or Tier 4 A Emissions compliant Glow plugs cold start Full flow engine oil filter Air cleaner replaceable dry type with radial seal Aspirated air cleaner Fuel filter with water trap Diesel Particulate Filter F spark arresting Fuel tank usable capacity 42 gal (159 L) High Pressure Common Rail computer controlled injection with diagnostic features Electronic throttles foot and rotary hand Antifreeze to -34 F (-37 C) Radiator with overflow bottle POWERTRAIN Standard Powershuttle, 4F-4R Power Shuttle Synchromesh transmission, manual gear shift, fully synchronized Front axle: 4WD heavy-duty mechanically driven front axle with 14.0 x 17.5 tires, limited slip differential and drive shaft guard POWERTRAIN (continued) Rear axle: 4WD heavy-duty outboard planetary drive with 21.0 x 24.0 tires Torque converter 12 in (305 mm) On-the-go electric 4WD control Electric F/R shuttle control Electric differential lock control, push-button Park brake, spring-applied, hydraulic release SAHR HYDRAULICS Ground level remote hydraulic test ports Variable displacement axial piston pump Maximum loader capacity: ,340 psi ( bar) Loader torque regulation: ,450 psi ( bar) Maximum backhoe capacity: ,100 psi ( bar) Backhoe torque regulation: ,450 psi ( bar) Heavy-duty oil cooler 7 micron, spin on oil filter LOADER See page 2 BACKHOE Power Lift See page 2 OTHER Front tire 12.5/80 x 18.0, 10-PR Rear tire 21.0 L x 24.0, 10-PR Forward tilt engine hood Replaceable, molded front bumpers Front/Rear tie downs Reflective logos Lights cab and canopy: 2 rear tail/stop 2 front flashers/turn 2 rear flashers/turn Cab only: 2 front driving lights 55 W Adjustable halogen work lights 55 W: 2 front 2 side left and right 4 rear Canopy only: 2 front driving lights 55 W Adjustable halogen work lights 55 W: 2 side left and right 2 rear OPTIONAL EQUIPMENT OPERATOR ENVIRONMENT Auto Ride Control 4WD models Standard Ride Control 2WD models Comfort Steering with momentary latching switch, two speed steering pump and 3rd/4th gear cutout ROPS/FOPS certified protective cab with rear wipers and floor mat Cab Convenience Package containing pull-down sun visor, window washer front and rear, left-hand storage tray, deluxe interior package, tilt steering column, sound Reduction Package for cab models levels reduced to 72 db (A), right-hand threshold storage box Pull-down sun visor for canopy models Radio AM/FM Stereo/WB, MP3 auxiliary input ENGINE Cold Weather Starting Aid with dual 12 Volt batteries Block heater POWERTRAIN Powershift S-Type transmission, 4F-3R fully synchronized electronic transmission controller and kick down in loader control lever 2WD or 4WD Powershift H-Type transmission, 4F-3R hydraulic clutch shifting with auto function HYDRAULICS Auxiliary backhoe unidirectional hydraulics Auxiliary backhoe bidirectional hydraulics: Hand lever operated for manual controls Button operated for pilot controls LOADER Auxiliary hydraulics for loader mounted equipment with thumb-operated proportional control Hydraulic front quick coupler Loader linkage without loader bucket Tool portfolio of additional attachments Buckets see page 2 BACKHOE Gripper teeth extensions on dipper Thumb-operated unidirectional auxiliary hydraulics with low flow from 0 to 36 gal/min (0 to 136 L/min) Thumb-operated bidirectional auxiliary hydraulic control Hydraulic bucket quick coupler Bucket retrofit kit Flip over stabilizer pads Cemetery/Street pads Buckets see page 2 OTHER Electrical master disconnect switch and remote jump-start Special paint Lift hooks export Front counterweights: 700 lb and 1,100 lb (318 kg and 500 kg) Rotating beacon Export protection package 580 Super N WT Page 6 of 7

7 NOTE: All specifications are stated in accordance with SAE Standards or Recommended Practices, where applicable. NOTE: All engines meet current EPA emissions requirements. IMPORTANT: Case Construction Equipment Inc. reserves the right to change these specifications without notice and without incurring any obligation relating to such change. Case Construction Equipment Inc. does not warrant the safety or reliability of attachments from other manufacturers. Case is a registered trademark of CNH America LLC. Any trademarks referred to herein, in association with goods and/or services of companies other than CNH America LLC, are the property of those respective companies. Form No. CCE SNWT Printed in U.S.A CNH America LLC Replaces form no. CCE SNWT 580 Super N WT Page 7 of 7 All Rights Reserved All Case construction equipment is biodiesel ready.

8 N SERIES BACKHOE LOADERS 580N 580 Super N 580 Super N WT 590 Super N

9 OUT MUSCLE. OUT POWER. OUTPERFORM. OUTLAST. When you re building one of the most versatile machines in the industry, where do you focus your strength? Everywhere. The best breakout force, the highest lifting capacity, the fastest roading speeds, the quietest cab the list of credentials is impressive. That s what happens when your legacy goes back to the world s first backhoe loader. So whether it s excavating, grading, craning, loading or removing snow, the N Series is engineered to outdo. PowerLift * *Not available on the 580N Over-Center Backhoe Design ProControl System (PCS) Comfort Steer 2

10 Models Available 580N 580 Super N 580 Super N WT 590 Super N Fully Integrated Hydraulic Quick Coupler* *Optional Second-to-None Serviceability 3

11 DIG, LIFT, LOAD AND ROAD BETTER. POWERLIFT TAKES TOUGHNESS UP A NOTCH* Our exclusive, push-button PowerLift feature unleashes the industry s most ferocious breakout force and a lifting capacity that outperforms the competition to the tune of nearly 1,200 lbs. Additional hydraulic power is channeled directly to the backhoe, giving the N Series strength comparable to an 8-ton excavator and greater precision when craning. *Not available on the 580N A QUICK BENEFIT OF OVER-CENTER DESIGN Our revolutionary over-center backhoe design locks the boom in toward the machine, transferring at least 15% of its weight to the front axle, which drastically improves stability to minimize porpoising during roading. You ll retain more material and comfortably travel up to an industry-leading 24 mph to, from and around the site. OPERATORS ASKED FOR IT AUTO-RIDE CONTROL Once only available on wheel loaders, CASE Auto-Ride Control is engineered into our 4WD loader backhoes. This spill-reducing feature automatically reduces loader arm bounce at elevated speeds and features industry-leading adjustable speed settings, giving operators full control of their load retention and comfort. SAME POWER, SAME TORQUE, LESS FUEL To meet Tier 4 Interim standards, a 3.4-liter turbocharged CEGR (Cooled Exhaust Gas Recirculation) engine delivers the performance of previous models while providing a faster throttle response and delivering fuel savings of 5-20%. And where other solutions required a larger hood that decreases visibility, ours stayed the same. That s going beyond compliance. DIG DEEPER. REACH FURTHER. LOAD FASTER. Every element of the CASE loader is designed for greater productivity. Longer arms make it easier to load in the center of a truck, a mechanical stopper causes metal-to-metal impact on full dump to shake out material and our in-line parallel linkage with a solid thru-pin design another industry first helps balance uneven loads. It s a loader like no other. Dump Cylinder Breakout Force Lift Capacity at Full Height 0 Case 580 Super N WT 8,425 11,450 Deere 310SK 7,419 11,051 Cat 420F IT 8,193 11,575 4,000 8,000 Lift Capacity in Pounds 12,000 4

12 PROCONTROL MEANS PRECISION When swinging the backhoe from side to side, our exclusive ProControl swing dampening system stops the boom exactly when and where you want. No wiggle. No rebound. No waiting for it to set. Just precise, responsive control. 5

13 MAXIMUM VISIBILITY. MINIMUM VOLUME. Floor-to-ceiling windows encircle the operator for exceptional sightlines of loader and backhoe. CASE also offers the quietest cab in the industry, with a sound rating as low as 72 dba. 6

14 STRENGTH FROM WITHIN. CUT TURNS IN HALF WITH COMFORT STEER Exclusive to CASE, the Comfort Steer option reduces lock-tolock rotations when moving from full-right to full-left (and vice versa). You can load, stockpile and backfill considerably faster with less operator discomfort throughout the day. THE MOST MANEUVERABLE CONTROLS AROUND Exclusive creature comforts such as infinitely adjustable pilot control towers that adjust fore/aft and tilt in/out, as well as comfortable armrests, adjustable wrist rests and a footrest help keep any sized operator comfortable. Pilot control towers offer industry-leading ergonomic design. LIGHTS, VISIBILITY, 360 ACTION All N Series machines feature high-intensity exterior lighting, including industry-inclusive Easy Flex side lighting. These adjustable lights have 45 rotation to provide overlapping fields of coverage for 360 visibility at night. COMMUNICATION IS A BREEZE All windows easily open by hand, including the rear-quarter window, which opens 180. Not only does this maximize airflow through the cab, it enables operators to clearly communicate with spotters all around the machine. SMARTCLUTCH DECIDE HOW IT DRIVES Operators can customize the feel of forward-to-reverse transitions, thanks to our industry-exclusive SmartClutch modulation. Aggressive or soft, set it to what you need. Adjustable Easy Flex side lights come standard. 7

15 MAINTENANCE MADE EASY. SERVICEABILITY IS IN OUR DNA When you invest in CASE equipment, you need it to last. We make it simple. The N Series is no exception. From swing-out coolers and outboard-mounted disc brakes to groundlevel site gauges and grouped service points located under a tilt-up hood, you can do daily maintenance in a matter of minutes. It s the easiest way to help you get the most performance and longest life out of your machine. < Add bevel to left edge EASY ACCESS TO EVERYTHING 1. Easiest safety strut to lower/raise 2. Spin-on filters 3. Flip-up hood 8 4. Outboard-mounted wet-disc brakes 5. Hydraulic diagnostic ports 6. Grouped site gauges SERVICE-FREE FEATURES: 7. Swing-out coolers 8. Safe jump-start terminal and master disconnect switch (optional) Lube-for-life U-joints Hardened steel triplebushed joints

16 NO TOOLS NEEDED The N Series backhoe loaders continue the CASE hallmark of simple serviceability with features like tool-free access to routine maintenance points. 9

17 REMOTE. CONTROL. SUPPORT COMES STANDARD Base & Extended Warranty Coverage * 2-Year/2,000-Hour Standard Powertrain Warranty available at no charge in addition to 1-Year/Unlimited-Hour Full-Coverage Base Warranty * Please see your CASE dealer for limitations, exclusions and confirmation of policies in effect. Purchased Protection Plan Extension of the factory base and extended coverage is available at an additional cost. Plans are available up to six years/7,500 hours on CASE N Series backhoe loaders. Talk to your CASE dealer to determine the plan that best fits your needs. Breakdown Assistance Standard on all CASE equipment. STRONGER PRODUCT SUPPORT SOLUTIONS Your CASE dealer knows best how you can maximize your equipment investment and uptime, with genuine CASE parts, expert service and a complete range of product support solutions including CASE remanufactured and all-makes parts. CASE supports better parts availability and faster deliveries, through nine parts distribution centers in North America and a forecasting system to ensure that the right parts will be there when you need them. And only CASE dealers have exclusive access to the Electronic Service Tool that quickly pinpoints machine issues to help maximize uptime. 10

18 Standard on all N Series backhoe loaders, CASE SiteWatch telematics breaks the boundaries of fleet management by allowing you to monitor and manage multiple machines from your office, wherever that may be. No more manually tracking down engine hours and fuel levels. Get real-time performance metrics, idle-time analytics, scheduled maintenance intervals and programmable security alerts sent to any computer, anytime, anywhere. 11

19 12

20 ATTACHED TO STRENGTH. INDUSTRY-EXCLUSIVE INTEGRATED HYDRAULIC QUICK-COUPLER Only CASE offers an integrated hydraulic quick coupler on our backhoes. Its unique design is factory built into the backhoe, so it doesn t alter the physics or breakout force of the machine like after-market options. You get the same industry-leading power with the added convenience of being able to switch out attachments from the comfort of the cab. SMARTFIT BUCKET TEETH N Series buckets come standard with the innovative SmartFit bucket tooth system. These heavy-duty, selfsharpening teeth combine exceptional strength and unmatched ease of installation thanks to a hammerless fastener system with reusable locking pins. Available in a full range of styles. 13

21 THE N SERIES BACKHOE LOADERS SPECIFICATIONS 580N 580 Super N 580 Super N WT 590 Super N Engine FPT F5H FPT F5H FPT F5H FPT F5H Gross hp 2200 RPM 85 (63.4) 97 (72.3) 97 (72.3) 110 (82) Net hp 2200 RPM 78 (59) 95 (71) 95 (71) 108 (81) Emissions certification* Tier 4 Interim (CEGR/DPF) Tier 4 Interim (CEGR/DPF) Tier 4 Interim (CEGR/DPF) Tier 4 Interim (CEGR/DPF) Operating weight, 4WD lb. (kg) 17,454 (7 917) 17,226 (7 814) 19,985 (9 065) 20,458 (9 280) Maximum net torque lb. ft. (N 1400 RPM 268 (364) 333 (452) 333 (452) 338 (458) Backhoe bucket force lbf (kn) 11,334 (50.4) 14,223 (63.2) 14,831 (65.9) 15,652 (69.6) Maximum travel speed fwd. mph (kph) 24.3 (39.1) 23.6 (38.0) 23.0 (37.0) 24.2 (38.9) System flow gpm (L/min) 28.5 (108) 41 (155.2) 41 (155.2) 43 (162.6) Lift capacity at full height lb. (kg) 6,803 (3 086) 7,044 (3 195) 8,425 (3 822) 8,325 (3 776) Backhoe boom lift groundline 2,858 (1 297) 3,513 (1 594) 2,904 (1 317) 3,160 (1 433) Bucket breakout force lb. (dan)** 11,312 (5 032) 11,658 (5 288) 11,674 (5 193) 13,717 (6 102) DIMENSIONS Height to top of cab 8 ft. 11 in. (2.72 m) 8 ft. 11 in. (2.72 m) 8 ft. 11 in. (2.72 m) 8 ft. 11 in. (2.72 m) Bucket hinge pin height fully raised 11 ft. 3 in. (3.42 m) 11 ft. 3 in. (3.42 m) 11 ft. 6 in. (3.50 m) 11 ft. 6 in. (3.50 m) Overall operating height fully raised 13 ft. 9 in. (4.18 m) 13 ft. 9 in. (4.18 m) 13 ft. 11 in. (4.24 m) 13 ft. 10 in. (4.22 m) Dump full height Dump full height, 45 dump 8 ft. 10 in. (2.69 m) 8 ft. 10 in. (2.69 m) 8 ft. 11 in. (2.72 m) 9 ft. 1 in. (2.77 m) Dump full height, 45 dump 31.5 in. (801 mm) 31.5 in. (801 mm) 27.0 in. (685 mm) 27.8 in. (707 mm) Bucket groundline Digging depth below grade bucket flat 6.1 in. (155 mm) 6.1 in. (155 mm) 6.1 in. (155 mm) 5.9 in. (150 mm) Wheelbase 84.5 in. (2.15 m) 84.5 in. (2.15 m) 84.5 in. (2.15 m) 84.5 in. (2.15 m) Reach from front axle centerline bucket on ground 6 ft. 1 in. (2.08 m) 6 ft. 8 in. (2.09 m) 6 ft. 8 in. (2.05 m) 6 ft. 5 in. (1.99 m) Turning radius at curb, 4WD, brakes applied 11 ft. 4 in. (3.45 m) 11 ft. 0 in. (3.36 m) 12 ft. 0 in. (3.65 m) 12 ft. 6 in. (3.81 m) Backhoe dig depth 18 ft. 3 in. (5.55 m) 17 ft. 11 in. (5.47 m) NOTE: Specification data calculated using same bucket determining operating weight unless otherwise specified. *CEGR = Cooled Exhaust Gas Recirculation; DPF = Diesel Particulate Filter. **Machine equipped with a 4-in-1 bucket. 18 ft. 0 in. (5.48 m) 19 ft. 6 in. (5.94 m) 14

22 BUILDING A STRONG CASE Already in high gear with the arrival of founder J.I. Case s portable steam engine in 1869, we found ourselves at the heart of the road construction boom of the early 1900s. The path was set. Today, CASE is a game changer in construction equipment, financing, parts and service. Revolutionary is nothing new to CASE, as innovations like the integrated loader/backhoe (1957), Ride Control, over-center boom design and ProCare have shown. It s this ingenuity and spirit that fuels our ongoing pursuit of building industry-leading performance and productivity into every machine throughout our full line of light, medium and heavy equipment. All of this is backed by a portfolio of more than 10,000 OEM, REMAN and Gold Value parts, more than 350 North American dealer locations, and unmatched financial and insurance services that ensure the best support is always within reach. When all is said and done, our strength is only as solid as the machines we engineer, the support and service we give, and most importantly, the vote of confidence CASE customers have with every bit of it. Specialized finance programs and flexible leasing packages put you in the driver s seat of industryleading CASE equipment, while no-nonsense warranties and comprehensive protection plans ensure that your equipment is protected. As the only finance company dedicated to CASE, we offer strong products and services designed around your unique needs and are the only ones supported by the helpful service professionals at your CASE dealer. To learn more about CASE or for attentive customer service, visit your nearest dealer, call CASE6 or visit us online at CaseCE.com. 15

23 CaseCE.com 2014 CNH Industrial America LLC. All rights reserved. CASE is a trademark registered in the United States and many other countries, owned by or licensed to CNH Industrial N.V., its subsidiaries or affiliates. CNH Industrial Capital is a trademark in the United States and many other countries, owned by or licensed to CNH Industrial N.V., its subsidiaries or affiliates. Printed in U.S.A. Form No. CCE201401TLB Always read the Operator s Manual before operating any equipment. Inspect equipment before using it, and be sure it is operating properly. Follow the product safety signs and use any safety features provided. NOTE: All engines meet current EPA emission regulations. NOTE: All specifications are stated in accordance with SAE Standards or Recommended Practices, where applicable. Contains 10% post-consumer fiber IMPORTANT: CASE Construction Equipment Inc. reserves the right to change these specifications without notice and without incurring any obligation relating to such change. Availability of some models and equipment builds vary according to the country in which the equipment is used. The illustrations and text may include optional equipment and accessories and may not include all standard equipment. Your CASE dealer/distributor will be able to give you details of the products and their specifications available in your area. CASE Construction Equipment is biodiesel friendly.