POWERED INDUSTRIAL TRUCK PROGRAM September 2015
|
|
|
- Betty Hart
- 6 years ago
- Views:
Transcription
1 A. SCOPE AND APPLICATION POWERED INDUSTRIAL TRUCK PROGRAM September 2015 The Powered Industrial Truck Program is established in accordance with 29 CFR , Powered Industrial Trucks, and describes the requirements for inspection and safe operation of powered industrial trucks at all University of Nevada, Las Vegas (UNLV) properties. B. COMPLIANCE This program applies to UNLV employees and student workers who operate powered industrial trucks (forklifts) at UNLV. C. DUTIES AND RESPONSIBILITIES (1) Risk Management and Safety (RMS) a. Establish the Powered Industrial Truck Program. b. Develop and offer training to powered industrial truck operators and certify operators (Appendix A). c. Provide refresher training as needed. (2) Department Managers and Supervisors a. Implement the Powered Industrial Truck Program. b. Verify that operators are trained and certified to operate powered industrial trucks and use all safety restraint devices provided. c. Schedule time for operators to attend training and complete certifications prior to assigning job tasks. d. Ensure that maintenance and repairs are completed by Vehicle Repair Services or authorized service provider. e. Remove powered industrial trucks from service that are not in safe operating condition. f. Evaluate operator performance on the job to ensure that safe work Page 1
2 Powered Industrial Truck Program practices are followed. g. Take appropriate corrective action (including refresher training) when: i. Individuals have observed operating powered industrial trucks unsafely. ii. iii. Operators have been involved in accidents or near-miss incidents. Workplace/equipment changes occur that could affect the safe operation of powered industrial trucks. h. Contact RMS to evaluate and approve individuals who will be assigned the responsibility of performing powered industrial truck certifications for the department. (3) Operators a. Receive authorization from supervisors to operate powered industrial trucks on campus. b. Complete Powered Industrial Truck training and certifications as required. c. Inspect powered industrial trucks before being placed in service and at least once per shift to determine that trucks are in safe working condition. d. Use the Forklift Pre-Operational Check (Appendix B) and the Forklift Functional Check (Appendix C) as guidelines when completing daily inspections. e. Notify supervisor immediately when deficiencies are found (including items such as illegible data plates) that prevents the safe operation of powered industrial trucks f. Take powered industrial trucks out of service when they are found to be unsafe. g. Handle fuel and liquefied petroleum gas (LP Gas) in a safe manner. h. Perform worksite inspections to identify and eliminate (if possible), or avoid operational conditions and hazards that my affect safe operation. i. Operate powered industrial trucks safely at all times and obey all traffic laws. j. Lower the forks, set controls to neutral, turn off power and set the brakes when powered industrial trucks are left unattended. Page 2
3 Page 3 Powered Industrial Truck Program Note: A powered industrial truck is unattended when the operator is 25 feet or more from the vehicle in view, or whenever the operator leaves the powered industrial truck and it is not in view. (4) Vehicle Repair Services a. Maintain powered industrial trucks in a safe operating condition. b. Install replacement parts that are approved by the manufacturer and equivalent to those used in the original design. D. MODIFYING AND MARKING POWERED INDUSTRIAL TRUCKS (1) Modifications or additions that affect the capacity or safe operation of powered industrial trucks shall not be made without written approval from the manufacturer. (2) Request for manufacturer s approval of modifications or additions shall only be made by Vehicle Repair Services. (3) Approved modifications shall be installed by Vehicle Repair Services or authorized service provider. (4) If modifications are made, a new data plate shall be obtained from the manufacturer to reflect changes to the powered industrial truck. (5) Front-end attachments not installed at the factory shall be marked to identify the attachment, its weight, and safe lifting capacity. E. TRAINING AND PERFORMANCE EVALUATION (1) Operators must attend initial classroom training and successfully complete certification prior to operating powered industrial trucks at UNLV. Note: Employees that provide documentation that shows successful completion of classroom training prior to employment at UNLV; will only be asked to pass the performance evaluation prior to operation of a powered industrial truck. (2) Trainees should be given an opportunity to practice prior to completing performance evaluations. (3) Trainee practice sessions will only occur under the direct supervision of a designated person who has the knowledge, training, and experience to evaluate their competence. (4) Trainee practice sessions will be conducted in areas that do not endanger the operator, other individuals, or cause property damage. (5) Course instruction and certifications shall be conducted by individuals who have the knowledge, training, and experience to train new operators
4 and/or evaluate operator competence. (6) Restoration of privileges to operate powered industrial trucks at UNLV shall follow acceptable completion of retraining and/or any other requirements specified. (7) Refresher Training may be required when: a. Operators have been observed operating powered industrial trucks in an unsafe manner. b. Operators have been involved in accidents or near-miss incidents. c. Workplace or equipment changes occur that could affect the safe operation of powered industrial trucks. (8) An evaluation of powered industrial truck operators performance shall be conducted at least once every three years. F. CONTRACTORS/SUB-CONTRACTORS (1) Contractors and sub-contractors whose job assignments require the use of powered industrial trucks while working on UNLV properties shall comply with the requirements specified in 29 CFR , Powered Industrial Trucks. (2) Operate powered industrial trucks safety at all times and obey all traffic laws. G. APPENDICES Appendix A Forklift Practical Evaluation Appendix B Forklift Pre-Operational Check Appendix C Forklift Functional Check Page 4
5 Appendix A Forklift Practical Evaluation Page 5
6 Appendix B Pre-Operational Check Page 6
7 Appendix B (continued) Pre-Operational Check Page 7
8 Appendix C Functional Check Page 8
9 Appendix C (continued) Functional Check Page 9
CART SAFETY and LOSS PREVENTION PROGRAM MAY 2018
CART SAFETY and LOSS PREVENTION PROGRAM MAY 2018 A. SCOPE AND APPLICATION The Cart Safety Program and Loss Prevention Program has been established to prevent loss, provide proper maintenance and ensure
Powered Industrial Trucks
INDIANA UNIVERSITY-PURDUE UNIVERSITY at INDIANAPOLIS IUPUI Department of Environmental Health and Safety 620 Union Drive, Room 043, Indianapolis, Indiana 46202 Powered Industrial Trucks Purpose and Background
SECTION 11 POWERED INDUSTRIAL TRUCKS
SECTION 11 POWERED INDUSTRIAL TRUCKS 11.1 Powered Industrial Truck Procedure 11.2 Forklift Inspection 11.3 Operator Performance Evaluation Checklist Revised: May 2009 Updated: November 2017 Reviewed: October
Powered Industrial Truck Safety Program
Powered Industrial Truck Safety Program 0 TABLE OF CONTENTS Forklift Safety Program 1.0 Overview.. 2 2.0 Purpose....2 3.0 Procedures..2 4.0 Responsibilities. 4 5.0 Training Requirements......5 Appendix
Forklift Safety Plan Contents: Forklift Safety Plan
Forklift Safety Plan Contents: Forklift Safety Plan Introduction... ii Plan Cover Sheet... 1 Purpose... 2 Supervisory Responsibilities... 2 Maintenance, Fueling, and Repair... 3 General Rules for Operator
Powered Industrial Vehicle Policy
Powered Industrial Vehicle Policy Policy The Flight Department is committed to protecting employees from the hazards involved in the operation of powered industrial vehicles. This Policy is established
SUNY GENESEO ENVIRONMENTAL HEALTH & SAFETY
Prepared by: Darlene Necaster Page 1 I. OVERVIEW Material handling is a significant safety concern. During the movement of products and materials, there are a number of opportunities for injuries and property
UC Irvine Environmental Health & Safety SECTION: TITLE: Powered Industrial Truck (Forklift) Safety Program
UC Irvine Environmental Health & Safety SECTION: TITLE: Powered Industrial Truck (Forklift) Safety Program INITIATOR: Desirée Villarreal REVISION DATE: 10/17/2014 1. Program Description 2. Scope 3. Definitions
ROUGH TERRAIN VEHICLES
ROUGH TERRAIN VEHICLES OPERATING SAFETY RULES AND PRACTICES Operator Responsibility Safe operation is the responsibility of the operator. The equipment can be dangerous if not used properly. The operator
UNIVERSITY OF TOLEDO
UNIVERSITY OF TOLEDO SUBJECT: POWERED INDUSTRIAL TRUCKS Procedure No: S-08-046 PROCEDURE STATEMENT All powered industrial truck operators must be licensed through the University of Toledo Environmental
Forklift and Industrial Trucks
Forklift and Industrial Trucks University Facilities Internal Procedure: July 1, 2013 Effective date: July 1, 2013 Last Modified: April 2013 Approved by: Bob Wells 1.0 Program Objective This program for
Industrial Truck (Forklift) Safety Program
University of North Carolina Wilmington Environmental Health & Safety Workplace Safety Industrial Truck (Forklift) Safety Program GENERAL The UNCW Environmental Health & Safety Department (EH&S) is authorized
Powered Industrial Trucks. Supersedes: 10/14 (Rev. 02) Preparer: Owner: Approver: EHS Team Member EHS Team Member EHS Manager
Procedure No.: PA-020-0057 Page: 1 of 14 Preparer: Owner: Approver: EHS Team Member EHS Team Member EHS Manager Document Revision Change Table Revision Number Revision Description Revised By Revision Date
Department guidelines and procedures are subject to change at any time and staff are responsible for familiarizing themselves with current guidelines.
Use of University Vehicles FACILITIES OPERATIONS AND MAINTENANCE GUIDELINES AND PROCEDURES Date Issued: 03/01/09 Guideline # USE OF UNIVERSITY VEHICLES PURPOSE: To establish guidelines for the use of Facilities
LIFT TRUCK POLICY AND PROGRAM
LIFT TRUCK POLICY AND PROGRAM Table of Contents 1.0 Policy Statement and Program Overview... 4 2.0 Lift Truck Applicable Legislation, Guidelines and Standards... 4 3.0 Forklift Program Requirements...
AERIAL LIFTS/MAN-LIFTS
AERIAL LIFTS/MAN-LIFTS Aerial lifts are pieces of equipment that many workers can't imagine working without. This equipment, if used correctly, provides quick and safe access to work areas that at one
UNIVERSITY OF ROCHESTER ENVIRONMENTAL HEALTH & SAFETY
Revision No.: New Page 1 of 11 I. PURPOSE Personal transportation via small and agile electric or gas powered vehicles is a convenience but also presents a unique set of hazards. This policy addresses
Fixed Ladder: A ladder that cannot be readily moved or carried because it is an integral part of a building or structure
Ladder Safety University of Tennessee Safety Guide GS-045 Document Contact: EHS-General Safety Date effective: May 1, 2013 Revision Date: May 1, 2013 Purpose The purpose of this procedure is to ensure
CRANE & HOIST SAFETY PROGRAM
CRANE & HOIST SAFETY PROGRAM 1.0 PURPOSE The purpose of the Crane and Hoist Safety Program is to: 1.1 Ensure a safe work environment for employees who operate, maintain, or work around cranes and hoists
Transporation Policies and Procedures CO 400.7:
Transporation Policies and Procedures CO 400.7: Purpose To provide a framework of Transportation policies and procedures that can be implemented at Morehouse College under the direction of the Physical
Powered Industrial Trucks Workgroup The workgroup met on to discuss the applicability of the proposed rule for general industry on Powered
e Powered Industrial Trucks Workgroup The workgroup met on 5-25-95 to discuss the applicability of the proposed rule for general industry on Powered Industrial Trucks as it would relate to the construction
RELIANT HOLDINGS LTD AND ITS AFFILIATES Safety Management System. Preparation: Safety Mgr Authority: CEO Issuing Dept: Safety Page: Page 1 of 5
Preparation: Safety Mgr Authority: CEO Issuing Dept: Safety Page: Page 1 of 5 Purpose This program is written to be in compliance with local regulatory requirements and provide directives to managers,
UNIVERSITY OF TOLEDO
UNIVERSITY OF TOLEDO SUBJECT: CRANE AND HOIST SAFETY PROGRAM Procedure No: S-08-024 PROCEDURE STATEMENT All crane and hoists operated on UT campuses must be adequately maintained and inspected as prescribed
RUTGERS UNIVERSITY POWERED INDUSTRIAL TRUCK PROGRAM
RUTGERS UNIVERSITY POWERED INDUSTRIAL TRUCK PROGRAM 9/01 1 TABLE OF CONTENTS POWERED INDUSTRIAL TRUCK PROGRAM A. PURPOSE AND SCOPE...1 B. LIFE TRUCK REQUIREMENTS...1 C. AREA REQUIREMENTS...2 D. RESPONSIBILITIES...2
Power Industrial Truck
C L O V I S U N I F I E D S C H O O L D I S T R I C T Trans po rt a tio n De par tme nt Power Industrial Truck Utility Cart, Golf Cart, Forklift, etc. PIT Driver Handbook Revised May, 2013 1 P I T D R
ESSENTIAL SAFETY RESOURCES
ESSENTIAL SAFETY RESOURCES GS-3009 DRIVING SAFETY Originator: Safety Advisor s Signature: Type Name Approval: HSE Manager s Signature: Type Name Approval: Operations Manager s Signature: Type Name Table
Fleet Safety. Latest revised date: October 26, 2011 Page 1 of 6 Prepared by: Department of Health & Safety S-008
Fleet Safety Latest revised date: October 26, 2011 Page 1 of 6 1.0 Introduction 1.1 University faculty and staff are eligible to operate University vehicles for the purpose of conducting University business.
University of Hartford Golf Cart/Utility Vehicle Policy & Procedures. Revised
University of Hartford Golf Cart/Utility Vehicle Policy & Procedures Revised Purpose: To establish standards for the safe use and operations of a Golf Cart/Utility Vehicle at the University of Hartford.
WEST VIRGINIA UNIVERSITY OFFICE of ENVIRONMENTAL HEALTH AND SAFETY TABLE OF CONTENTS
WEST VIRGINIA UNIVERSITY OFFICE of ENVIRONMENTAL HEALTH AND SAFETY TABLE OF CONTENTS 1.0 Scope...2 2.0 Purpose...2 3.0 Definitions...2 4.0 Roles and Responsibilities...2 5.0 Training...4 6.0 Procedures...7
Policies and Procedures
PAGE 1 OF 5 PURPOSE This policy has been developed to define standards of conduct and establish mandatory training for faculty, staff, students, volunteers or contractors/vendors who operate golf carts
DRIVING & CITY VEHICLES January To identify some rules relevant to use of vehicles; and,
A. PURPOSE The purpose of Section is to: 1. Set Authorized Driver standards; 2. To identify some rules relevant to use of vehicles; and, 3. To comply with IRS laws regarding taxation of commuter use of
Jay Industries, Inc. Powered Industrial Trucks (Forklifts) Written Program and Procedures
Jay Industries, Inc. Powered Industrial Trucks (Forklifts) Written Program and Procedures 07/02/11 JAY INDUSTRIES, INC. Jay Plastics Division Broshco Fabricated Products Crestline Paint Division Kronis
Table of Contents. Community College of Allegheny County Ladder. I. Objective. Assignment of Responsibilities. Selection of Ladders
This document is intended to provide basic safety guidelines for the Physical Plant Department at Community College of Allegheny County. The information provided in this guide may vary by site. Version
Newport News Shipbuilding Contractor Environmental, Health and Safety Resource Manual Cranes
Newport News Shipbuilding Contractor Environmental, Health and Safety Resource Manual Cranes Newport News Shipbuilding Page 1 CRANES 1. Hazard and Reference The use of cranes at NNS presents a serious
Environmental Health and Safety Office
Environmental Health and Safety Office Industrial Powered Trucks/ Forklift Safety August 2011 1.0 Purpose This policy has been developed to establish compliance with OSHA standard 29 CFR 1910.178 for industrial
Revision #: 14.4 Document #: Page: 1 of 5 Title: Mobile Aerial Work Platforms
Revision #: 14.4 Document #: 12.06 Page: 1 of 5 1. PURPOSE The purpose of this procedure is to provide guidance on the safe use of mobile aerial work platforms. 2. SCOPE This procedure applies to all employees
Table of Contents. Why An Occupational Health and Safety Program Demonstrating Commitment to Occupational Health and Safety... 1.
Table of Contents Foreword... i 1. Introduction Why An Occupational Health and Safety Program... 1.1 Demonstrating Commitment to Occupational Health and Safety... 1.4 Appendix I: District Commitment to
CLEARWATER FIRE & RESCUE TRAINING BUREAU
CLEARWATER FIRE & RESCUE TRAINING BUREAU TILLER OPERATOR TASK BOOK #4 Candidate Name (printed) Signature Beginning Date Candidate Station/Shift 08# Hire Date Lieutenant (print) Signature Completion date
USC Upstate Policy For The Safe Operation of Golf Carts, Accessibility Carts, Low Speed and Utility Vehicles on Campus
Effective Date: October 1, 2012 Annual Review Date: October USC Upstate Policy For The Safe Operation of Golf Carts, Accessibility Carts, Low Speed and Utility Vehicles on Campus 1 I. Purpose: USC Upstate
Safe Driving Standards & Procedures
Type: POLICY Revision: 01 Owner: BRL Document Name: HSPOL 016 Status: Current Nov 2014 Review Date: February 1, 2018 Effective Date: 01 January 2015 Total Pages: 5 Scope: The following standard applies
!!! Sample Written Program For Your Company! For! Forklift Safety!! Provided By: !!!
Sample Written Program For Your Company For Forklift Safety Provided By: P.O. Box 2136 Slidell, LA 70458 Phone: 985-781-1444 Fax: 985-718-4957 Email: info@se-safety.com Forklift & Motorized Pallet Jack
SECTION 14: AERIAL LIFT PROGRAM
SECTION 14: AERIAL LIFT PROGRAM Fisher Auto Parts is committed to promoting a safe and healthy environment for all employees and customers. Protection from accidental loss of any resources, especially
Powered Industrial Trucks (Forklifts)
Powered Industrial Trucks (Forklifts) The University Of Iowa Environmental Health & Safety 122 Grand Avenue Court Iowa City, IA 52242-1000 Phone: 319-335-8501 Date Revised/Reviewed: 5/16/2018 Table of
CLEARWATER FIRE & RESCUE TRAINING BUREAU
CLEARWATER FIRE & RESCUE TRAINING BUREAU TRACTOR OPERATOR TASK BOOK #5 Candidate Name (printed) Signature Signature Beginning Beginning Date Date Candidate Station/Shift 08# Hire Date Lieutenant (print)
Parked forklift crushes operator against semi-trailer
OR 2004-04-01 Parked forklift crushes operator against semi-trailer SUMMARY On February 10, 2004, a 42-year-old forklift operator was crushed between the forklift he had been operating and a semi-trailer
Tillman Insurance Agency, Inc. Driver Safety Manual
Tillman Insurance Agency, Inc. Driver Safety Manual September 6, 2008 1) Driver Qualifications All drivers must have the proper drivers license for the class of vehicle they are operating. All drivers
Use of District- Owned Vehicles Administrative Regulations (AR) New Driver Packet
Use of District- Owned Vehicles Administrative Regulations (AR) 3541.53 New Driver Packet Use of District Owned Vehicles o Steps for approval: o Review policy (Administrative Regulation 3541.53) Reviewed
MVR Evaluation. MVR Evaluation. When to Order MVRs. MVR Evaluation Tools. Loss Control Bulletin. MVR Point System
MVR Evaluation One of the most effective fleet management tools is a driver s Motor Vehicle Record (MVR). A MVR details an individual s past driving history indicating violations and accidents over a specified
Effective Date: 14-January Table of Contents
Version: 5 Page: 1 of 12 Table of Contents 1.0 Introduction... 2 1.1 Purpose... 2 1.2 Scope... 2 1.3 Definitions... 2 1.4 Responsibilities... 3 Environmental Health and Safety Office (EHSO) and applicable
POWERED INDUSTRIAL TRUCK OPERATIONS
POWERED INDUSTRIAL TRUCK OPERATIONS DEPARTMENT OF RISK MANAGEMENT AND SAFETY CREATED AUGUST 2009 Table of Contents INTRODUCTION... 1 RESPONSIBILITIES... 1 PRE-QUALIFICATIONS... 1 TRAINING... 1 LICENSING...
WAYNE COUNTY COMMUNITY COLLEGE DISTRICT MOTOR VEHICLE SAFETY POLICY
WAYNE COUNTY COMMUNITY COLLEGE DISTRICT MOTOR VEHICLE SAFETY POLICY 1. Policy Many employees operate company owned, leased, rental or personal vehicles as part of their jobs. Employees are expected to
City University of New York Automobile Use Policy
Introduction and Statement of Policy City University of New York Automobile Use Policy Each time a City University of New York (hereafter referred to as CUNY or University ) vehicle is operated in an inappropriate
Fort Valley State University Golf Cart/Utility Vehicle Use and Campus Vehicle Usage Policy
Fort Valley State University Golf Cart/Utility Vehicle Use and Campus Vehicle Usage Policy Purpose and Intent Personal Transportation vehicles This policy provides guidelines for the use of golf carts
Risk Control at United Fire Group
United Fire Group (UFG) believes the safety of the employee, public and the operations of a company is essential and every attempt must be made to reduce the possibility of accidents. The safety of the
FACILITIES MANAGEMENT POLICIES AND PROCEDURES. Director of Transportation Services and Work Management WCU MOTOR POOL 15-PASSENTER VAN POLICY
NUMBER: 807 DISTRIBUTION: FACILITIES MANAGEMENT POLICIES AND PROCEDURES ISSUED BY: Director of Transportation Services and Work Management EFFECTIVE: SUBJECT: WCU MOTOR POOL 15-PASSENTER VAN POLICY I.
APPENDIX D - ELECTRIC CART REGULATIONS TERMINAL BUILDING
APPENDIX D - ELECTRIC CART REGULATIONS TERMINAL BUILDING A. Scope These Rules and Regulations outline the requirements and procedures for the safe operation of electric cart vehicles (hereinafter Vehicles
San Ramon Valley Unified School District
San Ramon Valley Unified School District Parent Handbook Special Education Transportation 3280 E. Crow Canyon Road, San Ramon, California 94583 Director of Transportation, Sheri Glaser Dispatch (925) 824-0264
UNIVERSITY OF ARKANSAS SYSTEM VEHICLE SAFETY PROGRAM
UNIVERSITY OF ARKANSAS SYSTEM VEHICLE SAFETY PROGRAM JUNE 2014 PURPOSE The University of Arkansas vehicle driver safety program is intended to ensure maximum safety for all drivers and passengers of University
SECTION 25-MOTORIZED CART SAFETY
SECTION 25-MOTORIZED CART SAFETY 25.1 Operator Guidelines 25.2 Motorized Cart Inventory List 25.3 Vehicle Inspection Checklist (optional) 25.4 Motorized Cart Safety Acknowledgement Form Aug. 2010 Updated:
Provide a safe working environment, Govern operator use of heavy equipment, and Ensure proper care and maintenance of heavy equipment.
Heavy Equipment Operation Procedures for Construction Purpose The written Heavy Equipment Operation Procedures for Construction establish guidelines to be followed whenever any of our employees work with
Authorized Driver Policy and Procedures
Authorized Driver Policy and Procedures In order to comply with the Arizona Administrative Code Fleet Safety Policy (R2-10- 207.12), NAU must institute the requirements contained in this policy. Departmental
2018 NDE Pupil Transportation Reminders
2018 NDE Pupil Transportation Reminders Effective January 1, 2019, DMV will no longer issue school bus permits per LB347. At that time, the Nebraska Safety Center will be begin handling the qualification
Powered Industrial Trucks - Operator Training
Powered Industrial Trucks - Operator Training 1910.178 (l) 1915.120 (a) 1917.1 (a)(2)(xiv xiv) 1918.1 (b)(10) 1926.602 (d) Disclaimer This presentation is intended as a resource for providing training
LIFT TRUCK SAFETY OPERATOR TRAINING
LIFT TRUCK SAFETY OPERATOR TRAINING Avoiding Injury One person and a lift truck can move large amounts of material with ease and efficiency. Employers are responsible for training operators in the safe
EL DORADO UNION HIGH SCHOOL DISTRICT ADMINISTRATIVE REGULATION
EL DORADO UNION HIGH SCHOOL DISTRICT ADMINISTRATIVE REGULATION Business and Noninstructional Operations TRANSPORTATION SAFETY AND EMERGENCIES AR 3543 Cautionary Notice: AB 1610 amended Government Code
Operation of Fork Lift Trucks
Operation of Fork Lift Trucks 1. PURPOSE The purpose of this Procedure is to define the rules for the safe operation of Forklift trucks within the University. 2. SCOPE These rules apply to all rider-type
What Industrial Contractors Need to Know About MSHA Before Work at a Mine Site?
Session No. 663 What Industrial Contractors Need to Know About MSHA Before Work at a Mine Site? Terry Keenan Corporate Safety Director McCormick Construction Inc. Greenfield, MN Paper Scope and Focus This
ANS Vehicle Fleet Safety Policy
ANS Vehicle Fleet Safety Policy The purpose of this Policy is to ensure the safety of those individuals who operate a vehicle for Company business. Vehicle accidents are costly to our company, but more
Handbook EL-804 May 8, 2008 Transmittal Letter
Safe Driver Program Handbook EL-804 May 8, 2008 Transmittal Letter A. Explanation The purpose of this new handbook is to establish policy and provide guidelines to ensure that Postal Service drivers are
APPLICABILITY This procedure applies to all Ogeechee Technical College employees who drive on State of Georgia business regardless of frequency.
PROCEDURE: 3.3.2p1. Use of College Vehicles Revised: September 17, 2008; October 21, 2009; September 16, 2010; September 21, 2011; September 19, 2012; September 18, 2013; September 17, 2014; September
4.1. Environmental Health and Safety Office (EHSO) and applicable Emory Healthcare (EHC) Safety Management
Effective Date: 12/10/14 Version: 4 Page: 1 of 15 1. PURPOSE The purpose of this program is to protect the health and safety of all Emory employees assigned to operate powered industrial trucks as prescribed
PORTABLE LADDER SAFETY PROGRAM
PORTABLE LADDER SAFETY PROGRAM REGULATORY STANDARD: OSHA - 29 CFR 1910.25 Portable Wood Ladders* - 29 CFR 1910.26 Portable Metal Ladders* - 29 CFR 1926.1050-1060* *The above standards are intended to prescribe
SAINT MARY S COLLEGE OF CALIFORNIA STANDARD POWERED INDUSTRIAL TRUCK OPERATION. Prepared by
SAINT MARY S COLLEGE OF CALIFORNIA STANDARD 1.1.1 POWERED INDUSTRIAL TRUCK OPERATION Prepared by SAINT MARY S COLLEGE OF CA MORAGA, California KAREN LAURICELLA Original Date: 22 MAY, 2003 Effectivity:
THE UNIVERSITY OF MAINE AT PRESQUE ISLE. Powered Industrial Trucks & other vehicles
THE UNIVERSITY OF MAINE AT PRESQUE ISLE Powered Industrial Trucks & other vehicles General The Powered Industrial Truck Policy applies to the operation of forklifts, pallet jacks, platform-mounted trucks,
Possess a valid CDL with proper endorsements for the vehicle being driven;
581-053-0220 School Bus Driver s Permit and Certificate (1) No person shall transport pupils in a school bus or a vehicle that has a capacity of more than 20 passengers and not subject to regulations promulgated
Guidelines for Safety Training of Overhead Crane Operators and Supervisors
Guidelines for Safety Training of Overhead Crane Operators and Supervisors Purpose These guidelines present minimum recommended safety requirements for ensuring the safe and efficient operation of overhead
To reduce and eliminate at-fault crash, costs and injuries by promoting a safe driving culture within the organisation.
Safe Driving Policy Date: 19.03.2012 To be updated: 19.03.2013 Aim of this policy To reduce and eliminate at-fault crash, costs and injuries by promoting a safe driving culture within the organisation.
PURPOSE... 1 II. SCOPE... 2 III. REFERENCES... 2 IV. RESPONSIBILITIES...
Reed College 3203 Southeast Woodstock Blvd. Portland Oregon 97202-8199 Crane Safety Policy Effective Date: Revision Dates: February 9, 2011, June 25, 2012, July 2016 Review Dates: I. PURPOSE... 1 II. SCOPE...
DATE ISSUED: 9/13/ of 5 LDU DBA(REGULATION)-X
Records for Professional Personnel Incomplete Records Records for Support Personnel Driving Requirements for Drivers of District Vehicles Driving Record Evaluation The following records are required to
UNIVERSITY OF ARKANSAS SYSTEM VEHICLE SAFETY PROGRAM
UNIVERSITY OF ARKANSAS SYSTEM VEHICLE SAFETY PROGRAM OCTOBER 2008 PURPOSE The University of Arkansas vehicle driver safety program is intended to ensure maximum safety for all drivers and passengers of
FOR THE MANAGEMENT OF POWERED INDUSTRIAL TRUCKS
BEST MANAGEMENT PRACTICE FOR THE MANAGEMENT OF POWERED INDUSTRIAL TRUCKS PREPARED BY THE BREWERS ASSOCIATION SAFETY SUBCOMMITTEE TABLE OF CONTENTS Purpose.... 3 Summary.... 3 Frequently Asked Questions...
Arkansas State University - Jonesboro
Arkansas State University - Jonesboro Effective Date: 01/12/01 Number: 04-24 Section: Facilities and Services Subject: Facilities - University Vehicles Purpose This procedure is designed to assist ASU
Section 27 Brieser Construction SH&E Manual
Brieser Construction SH&E Manual January 2017 This program establishes the minimum requirements for the operation of aerial work platforms used in the course of work performed by personnel. This program
Section Sixteen. Transportation
Section Sixteen Transportation Section 16 TRANSPORTATION Lakehead District School Board Policies and Procedures Lakehead District School Board services a very large area. With the intent of providing this
Choctaw Nation of Oklahoma Fleet Safety Program
Choctaw Nation of Oklahoma Fleet Safety Program Fleet Safety Program Table of Contents I. Objective II. Scope III. Responsibilities IV. Training V. Implementation VI. Vehicle Inspection VII. Driving Safely
COMMERCIAL DRIVER APPLICATION
Date: COMMERCIAL DRIVER APPLICATION Professional Transportation Services, Inc PO Box 2368 541-826-7645 tel 541-826-8921 fax Name: First Middle Last Address Home telephone: City State Zip Cellular telephone:
East Lake Tarpon Special Fire Control District
East Lake Tarpon Special Fire Control District Implementation Date: 11/2000 Forms or Attachments: None SOP 803 Vehicle Safety Revision Date(s): 07/2004 Reviewed Date(s): A. All operators of Departmental
Ladder Safety Program
Ladder Safety Program For Adopted LC-1022 Rev. 06/16 Page 1 I. Introduction The Organization recognizes that employees use ladders on a regular
DUQUESNE UNIVERSITY FORKLIFT SAFETY PROGRAM
DUQUESNE UNIVERSITY FORKLIFT SAFETY PROGRAM Prepared by: Environmental Health and Safety Department TABLE OF CONTENTS Page Purpose 1 Driver Qualifications 1 Operator Training 2 Refresher Training 2 Evaluations
Gilmer ISD Transportation Department
Gilmer ISD Transportation Department Requirements to Drive a Bus Welcome to Gilmer ISD. This information is provided to help you in the process and requirements of being able to drive a school bus for
The University of Louisiana at Monroe Utility Vehicle Safety Policy
The University of Louisiana at Monroe 1. Introduction The information and instructions included in this policy will enable operators of utility vehicles to avoid situations that may compromise their safety
Electrical Safety CSA Z462 & NB Regulations
Electrical Safety CSA Z462 & NB Regulations WorkSafeNB s 2014 Health and Safety Conference Daniel Roberts Senior Manager, Electrical Safety Consulting at Schneider Electric Vice-chair CSA Z462 daniel.roberts@schneider-electric.com
Caterpillar Heavy Equipment Blind Spots
Caterpillar Heavy Blind Spots Free PDF ebook Download: Caterpillar Blind Spots Download or Read Online ebook caterpillar heavy equipment blind spots in PDF Format From The Best User Guide Database May
Position Paper. Telehandler Use: Lifting Suspended Loads
Position Paper Telehandler Use: Lifting Suspended Loads The following paper reflects the considered opinion on the Crane Association of New Zealand (Inc.) This document has been prepared by the Technical
Environmental Health and Safety Last Reviewed: September 10, 2018
CART/UTILITY VEHICLE OPERATION Philosophy: I. INTRODUCTION This procedure outlines requirements for the use of electric, solar or gaspowered carts and/or similar utility type vehicles (carts) on all campuses
Safe Driving Policy. 1. Objectives of the policy. 2. Code of conduct. 3. Responsibilities as an employee. Rev. Number 4 Page: Page 1 of 5
Title: Safe Driving Policy : THG_POL_10 Page: Page 1 of 5 7/2/201 1. Objectives of the policy HS&E Chairman: : Safe Driving Policy a. To ensure that all company vehicles are operated by authorized drivers
PAGE 1 OF 6 HEALTH, SAFETY & ENVIROMENTAL MANUAL PROCEDURE: S450 Motor Vehicle Safety REV /01/09
PAGE 1 OF 6 PURPOSE: MOTOR VEHICLE SAFETY To define the Company s requirement that drivers must possess the appropriate license for the type of vehicle to be operated and must comply at all times with
Vehicle Operation Procedure HSE
1 Purpose and Scope The Purpose of this Procedure is to prevent injury to personnel and damage to property through the safe operation of vehicles. This Vehicle Operation Procedure provides mandatory requirements
Policy on Use of Vehicles for University Purposes
SAFETY AND SECURITY Effective Date: October 24, 2014 Date Revised: December 15, 2017 Supersedes: N/A Related Policies: Policy on Professional Standards and Business Conduct Responsible Office/Department:
Middlebury College. Driver s License Program
Middlebury College Driver s License Program Revision Date: 9/2015 For the most current revision, refer to: http://www.middlebury.edu/offices/health/ehs/policies/driverslicense 1.0 Scope This policy applies