Electric wiring kit for towbars / 13-pin / 12 Volt / ISO 11446

Transcription

1 BMW 3 Series F30 03/4-> 3 Series F3 03/4-> 3 Series F34 03/4-> 4 Series F3 03/4-> 4 Series F33 03/4-> 4 Series F36 06/4-> Part No: Electric wiring kit for towbars / 3-pin / Volt / ISO 446 This electric kit has to be installed by a professional workshop or a suitable qualified person. The installation instructions must have been read and fully understood before the start of any installation. Please contact your wiring kit provider or the hotline shown in the footer should you need assistance! Make sure the vehicle is approved/homologated by the manufacturer to tow a trailer! lso please check that there is a definite compatibility between this vehicle and the electric kit! Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook. The fitting instructions contain important information relating to the use and function of the towing kit as well as for any diagnostic or activation process, that might have to be repeated in the future (e.g. after the performance of a vehicle software update). ll warranty claims will be forfeited if the electric kit or components contained therein are used incorrectly or modified. If a towing socket adaptor has been used to connect to the trailer or bike rack, this must be removed from the trailer socket once the trailer or bike rack has been disconnected. If the trailer or bike rack is not equipped with a rear fog lamp, depending on the towing vehicle type, the correct function of the towing kit cannot be guaranteed. In such cases, a rear fog lamp should be retro fitted. This towing electric kit will not be covered under warranty if any technical or electrical modifications or software updates have been performed by the vehicle manufacturer after the initial commissioning of the kit. That applies especially to modifications or updates which may cause malfunctions in the trailer socket or any other part of the trailer electrical equipment! Depending on the type of trailer module used in this electric kit, diagnostic interrogation with the vehicle s electrical system may be limited or will not function. The error memory inside the trailer module may not be able to be accessed by vehicle manufacturers diagnostic system. Error logs relating to the trailer electrical equipment, that may be generated in the vehicle manufacturers diagnostic system as a result of a test procedure, may be due to the incorrect installation of the towing electric kit or the false activation of the trailer module. We always recommend whenever possible, the following troubleshooting process: n analysis of the vehicle s error memory and possibly clearing of all faults before the start of the installation! Try disconnecting the trailer module form the towing harness and re-start the fault clearing process! If in doubt, limit the time for troubleshooting to a max of 0,5 hours and call our Technical Support Team! Please follow our instructions carefully and always test the towing electrics using a true lighting board or a specifically designed bulb tester. If an LED tester is used, ensure it is equipped with correct load resistors or malfunctions will occur! This instruction is subject to changes and we reserve the right to make changes to design, colour etc. ll of the data and illustrations may not be an exact representation but the text contained in this instructions must be observed! /6

2 Part No: **-***-*** Electric wiring kit for towbars / 3-pin / Volt / ISO 446 This electric kit has to be installed by a professional workshop or a suitable qualified person. The installation instructions must have been read and fully understood before the start of any installation. Please contact your wiring kit provider or the hotline shown in the footer should you need assistance! Make sure the vehicle is approved/homologated by the manufacturer to tow a trailer! lso please check that there is a definite compatibility between this vehicle and the electric kit! Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook. The fitting instructions contain important information relating to the use and function of the towing kit as well as for any diagnostic or activation process, that might have to be repeated in the future (e.g. after the performance of a vehicle software update). ll warranty claims will be forfeited if the electric kit or components contained therein are used incorrectly or modified. If a towing socket adaptor has been used to connect to the trailer or bike rack, this must be removed from the trailer socket once the trailer or bike rack has been disconnected. If the trailer or bike rack is not equipped with a rear fog lamp, depending on the towing vehicle type, the correct function of the towing kit cannot be guaranteed. In such cases, a rear fog lamp should be retro fitted. This towing electric kit will not be covered under warranty if any technical or electrical modifications or software updates have been performed by the vehicle manufacturer after the initial commissioning of the kit. That applies especially to modifications or updates which may cause malfunctions in the trailer socket or any other part of the trailer electrical equipment! Depending on the type of trailer module used in this electric kit, diagnostic interrogation with the vehicle s electrical system may be limited or will not function. The error memory inside the trailer module may not be able to be accessed by vehicle manufacturers diagnostic system. Error logs relating to the trailer electrical equipment, that may be generated in the vehicle manufacturers diagnostic system as a result of a test procedure, may be due to the incorrect installation of the towing electric kit or the false activation of the trailer module. We always recommend whenever possible, the following troubleshooting process: n analysis of the vehicle s error memory and possibly clearing of all faults before the start of the installation! Try disconnecting the trailer module form the towing harness and re-start the fault clearing process! If in doubt, limit the time for troubleshooting to a max of 0,5 hours and call our Technical Support Team! Please follow our instructions carefully and always test the towing electrics using a true lighting board or a specifically designed bulb tester. If an LED tester is used, ensure it is equipped with correct load resistors or malfunctions will occur! This instruction is subject to changes and we reserve the right to make changes to design, colour etc. ll of the data and illustrations may not be an exact representation but the text contained in this instructions must be observed! evision: / XX.XX.XXX XX-XXX-XXX Product overview M U U M T X B 5x G 3x 3x 5 mp. x 0 mp. x 5 mp. x 4x 3x 4x 5 mp. minifuse 3x 0 mp. minifuse 5 mp. minifuse x 0x /6

3 + + SYMBOL EXPLNTION Left (58-L) respectively t (58-) tail light V Cigarette lighter / accessory socket Stop light (54) / high mounted, third stop light (54) Loudspeaker / buzzer L Turn signal indicator left Park Distance Control Turn signal indicator right Switch / source of function ear fog light(s) Connect together everse eversing light(s) Disconnect Permanent power supply / 3pin socket, chamber 9 Charging wire for trailer battery / 3pin socket, chamber 0 Look at / See further information Look carefully at selected area Trailer / trailer recognition Present / Occupied / OK +30 Permanent current power supply Not present / Not occupied / Not OK Ground or Earth (3) coustic indication Ground connection battery terminal lug ttention / important advice Positive connection battery terminal lug 0 mp. 0 mp. Fuse / fuse capacity 0 mpère TOOLS C o C o TNTION! The vehicle's cooling capacity may have to be increased when retrofitting a trailer coupling! You must observe the manufacturer's instructions!!! Note: It may be necessary to check if this vehicle has a stored radio code before disconnecting the battery! Code 3:3 TNTION! In order to avoid mal-functions and damage to the vehicle s electrical system the earth terminal must be disconnected from the vehicle s battery before starting work! Both the trailer module and the vehicle s control unit for the electrical system can be damaged during work on the data bus connections if the battery is not disconnected! Please pay attention to the manufacturer s instructions when disconnecting and reconnecting the vehicle s battery! 3/6

4 F33 F30/ F F /6

5 F mm 3 ø 40mm X 90 mm T 3 SEL WITH SILICONE /6

6 + + X 8 SOCKET CONNECTION DIN/ISO 446 Pmax L -8 STOP everse 0 9 /L 3/3 4/ 5/58-6/54 7/58-L W W W 4W 3xW 4W W 40W 80W Colour Yellow Blue White Green Brown ed Black Pink Orange Grey White/ Black - White/ ed 9 Pin-out Tool 0 X 6/6

7 X F33 0 mm G 3 F30/F3/F3/F34 0 mm G 4 7/6

8 3 M M 4 M 5 M 6 Important! Please note informations in picture! Black/Grey PIN Black 54-Pol Black 54-Pin Black/Green Black/Grey Black/Grey /6

9 F30/ F3/F3 Blue/ed F33 Blue/ed /6

10 F34 Blue/ed Black 54-Pol Black 54-Pin Important! Please note informations in picture! CN-Data Wire Yellow/ed Yellow/Brown! Yellow/ed Yellow/Brown B Yellow Yellow/Brown B Black Yellow/ed Yellow Black B 0/6

11 mp. 0 mp. minifuse 0 mp. 0 mp. minifuse ed/blue Orange 5 mp. 5 mp. minifuse 5 mp. 5 mp. minifuse 0 mp. Yellow ed/yellow U 5 mp. 0 mp. 5 mp. ed/blue Yellow U Orange ed/yellow 4 /6

12 + 3 U U 5 0 mm U U 6 INFO >3.5V V ON <.5V (min 8 sec) V OFF PIN 0 /6

13 IMPOTNT! The Voltage Control Module (VCM) in this kit is designed to be self switching at a pre-set voltage input. With the engine started, the switched output (e.g. caravan fridge or alternative), pin 0, will switch on at a preset gure of 3,5 volts. When the engine is switched off, the switched output will remain live until the vehicle battery voltage drops to a preset ure of approx,5 volts. NO: The cut-off voltage depends on the condition of the vehicle battery, power consumption of the fridge etc. In all cases, the cut-of ure is preset so the vehicle engine can be started at any time. 8! Code 3:3 9 Option Jifeline We recommend a configuration for tow bar operations, with an online coding session with JIFELINE or with an approved Jifeline Partner 30 3/6

14 + + Option Only vehicles with PDC on front & back! 3 Optional Trailer Simulator for 7- and 3-pin Sockets 3 L everse /6

15 C PMx000 H 6:00 M 36 F 80 Driving ids OK MENU 60 km/h 6666 miles 500 miles 60 0 / PMx000! L P LED L km/h PMx000 C H C Trailer Indicator ! Trailer Indicator The following lamp functions for the trailer are not supported by all towing vehicles with DL circuit:! ear lights Side lights Numberplate lights The parking lights or dimmed headlights must be switched on to activate this function! 35 Optional dapter socket 3-pin 7-pin 36 5/6

16 Part No: **-***-*** Electric wiring kit for towbars / 3-pin / Volt / ISO 446 This electric kit has to be installed by a professional workshop or a suitable qualified person. The installation instructions must have been read and fully understood before the start of any installation. Please contact your wiring kit provider or the hotline shown in the footer should you need assistance! Make sure the vehicle is approved/homologated by the manufacturer to tow a trailer! lso please check that there is a definite compatibility between this vehicle and the electric kit! Following the installation of the electric kit, the fitting instructions should be kept together with the vehicle service document and vehicle handbook. The fitting instructions contain important information relating to the use and function of the towing kit as well as for any diagnostic or activation process, that might have to be repeated in the future (e.g. after the performance of a vehicle software update). ll warranty claims will be forfeited if the electric kit or components contained therein are used incorrectly or modified. If a towing socket adaptor has been used to connect to the trailer or bike rack, this must be removed from the trailer socket once the trailer or bike rack has been disconnected. If the trailer or bike rack is not equipped with a rear fog lamp, depending on the towing vehicle type, the correct function of the towing kit cannot be guaranteed. In such cases, a rear fog lamp should be retro fitted. This towing electric kit will not be covered under warranty if any technical or electrical modifications or software updates have been performed by the vehicle manufacturer after the initial commissioning of the kit. That applies especially to modifications or updates which may cause malfunctions in the trailer socket or any other part of the trailer electrical equipment! Depending on the type of trailer module used in this electric kit, diagnostic interrogation with the vehicle s electrical system may be limited or will not function. The error memory inside the trailer module may not be able to be accessed by vehicle manufacturers diagnostic system. Error logs relating to the trailer electrical equipment, that may be generated in the vehicle manufacturers diagnostic system as a result of a test procedure, may be due to the incorrect installation of the towing electric kit or the false activation of the trailer module. We always recommend whenever possible, the following troubleshooting process: n analysis of the vehicle s error memory and possibly clearing of all faults before the start of the installation! Try disconnecting the trailer module form the towing harness and re-start the fault clearing process! If in doubt, limit the time for troubleshooting to a max of 0,5 hours and call our Technical Support Team! Please follow our instructions carefully and always test the towing electrics using a true lighting board or a specifically designed bulb tester. If an LED tester is used, ensure it is equipped with correct load resistors or malfunctions will occur! This instruction is subject to changes and we reserve the right to make changes to design, colour etc. ll of the data and illustrations may not be an exact representation but the text contained in this instructions must be observed! evision: / XX.XX.XXX XX-XXX-XXX 37 Product overview 38 6/6