AutoSteer Installation Guide
|
|
- Miles Quinn
- 5 years ago
- Views:
Transcription
1 AutoSteer Installation Guide Covers AutoSteer (IK# Rev 01) installation on the following tractors: AutoFarm NOVARIANT INC Willow Road, Menlo Park/CA JD-7720 MFWD JD-7820 MFWD JD-7920 MFWD P# Rev /2005 1
2 Introduction This installation guide specifies the correct mounting positions for all the AutoSteer brackets and hardware on the machine. Refer to an AutoFarm Wheeled Tractor Installation Manual for full details on cable connections, AutoSteer system startup and calibration. Attention Tighten all screws, bolts, nuts, hose connections and cable connections after final assembly of AutoSteer system on machine. Special Requirements The tractor must be equipped with Power Beyond ports before starting your AutoSteer installation. If the tractor does not have a factory installed power beyond, you must order and install the John Deere power beyond accessory kit before starting the AutoSteer installation. 2
3 Special Tools Required 1. Metric Allen keys including larger 10-12mm sizes 2. Soft brush 3. Clean rags 4. Oil collection pan (for collecting oil when hose connections are opened) 5. Metric open wrenches 6. Metric socket wrenches up to 24mm 3
4 Installation Kit Overview JD-7920 Tractor Cab Box Bracket Assy. P# Steering Cable P# Wheel Angle Sensor Kit P# Cable Routing Hardware P# Valve Bracket Assy AutoSteer Valve Assy. P# Hydraulic Hose Kit with Adapters P# Install Guide P# P# Rev. A 10/2004
5 General Installation Sequence 1. Install the roof array on cab roof and rout antenna cables into the cab 2. Install the monitor 3. Install the cab box and power cable 4. Connect the monitor cable and antenna cables on cab box 5. Install the AutoSteer valve 6. Install all the hydraulic hoses 7. Install the steering cable between cab box and valve 8. Install the wheel angle sensor on front axle 9. Connect the cable between the valve and the wheel angle sensor 10. Check all hose and cable connections 11. Turn on the engine and check manual steering right and left and check for oil leaks. 12. Turn on the Cab Box and verify if AutoSteer display is working 13. Select wheeled tractor for vehicle type when prompted 14. Adjust the wheel angle sensor for correct counts between a hard left and hard right turn 15. Verify if the wheels turn right and left in AutoSteer calibration mode. 16. Follow complete AutoSteer calibration procedures before delivering machine to customer. 5
6 Roof Array Installation 6
7 Mounting Points for Roof Array on Tractor Cab Roof Remove these two M16 bolts for mounting the Roof Array Cab Roof 7
8 Roof Array Identification GPS L1 antenna Cable connectors that will be connected to the Cab Box Antenna cables (4x) Mount for radio wip antenna GPS L1 antenna LEFT SIDE OF TRACTOR RIGHT SIDE OF TRACTOR GPS L1/L2 antenna ROOF ARRAY 8
9 Roof Array Installed Secure the roof array using the two original tractor bolts through these holes Install the roof array with the single GPS antenna on the right side of the tractor RIGHT LEFT 9
10 Radio Antenna Radio Modem Wip Antenna Roof array 1. Install the radio wip antenna on the roof array as shown above 2. Remember to install rubber ring between the antenna and the base mount. 3. Hand tighten the antenna onto the threaded base. Do not use tools. WARNING! To avoid electrical shock hazard, the wip antenna must be removed from the cab roof before transporting the tractor on a truck or trailer and before driving the tractor under low objects and electrical power lines. 10
11 Monitor & Cab Box Installation 11
12 Monitor & Cab Box Mounting Position Right Side Cab Post Locate the two threads on the right side cab post That will be used for mounting the bracket that holds The monitor & cab box. Threads for Mounting Bracket 12
13 Assembling the Monitor & Cab Box bracket Slider bracket for the cab box Mounting bolts (for securing to cab post) Slider bracket for the monitor Phillips screws with lock nuts (4x) ¼-20 flat Head Phillips screws With nuts (4x) Assemble the slider brackets onto the main bracket using the parts and screws shown above. Do this pre assembly before installing inside the tractor cab. Main bracket for monitor and cab box 13
14 Monitor & Cab Box Bracket Installation Slider bracket for installing the monitor arm M10 Bolts & washers Mount the bracket over the two threads in the position shown using the two M10 bolts & washers provided Slider bracket for installing the cab box 14
15 Assembling the Monitor Arm AutoFarm Monitor Slider plate Mounting Plate Adjustable Monitor Arm 1. Mount the monitor onto the adjustable arm as shown above. 2. The monitor is secured to the mounting plate with three nuts. 15
16 Monitor & Cab Box Installed in Tractor Cab Right side Cab post Red Kill Switch must always be depressed when driving the tractor on roads or public areas On/Off Switch Monitor Installed Cab Box Installed 16
17 Wheel Angle Sensor Installation 17
18 Wheel Angle Sensor Assembly Wheel angle sensor (potentiometer) Connector for cable Ball joints This hole is for mounting on existing bolt on right side tie rod Hole for securing the cable with cable tie Tie rod bracket This hole is for mounting on existing bolt on differential housing Linkage rod (adjust length to 10.5 Between centers) Bracket for the wheel angle sensor Linkage arm (adjust length to 5.5 Between centers) Pre-assemble the wheel angle sensor with the linkages and brackets as shown above. Do not tighten bolts and nuts because it will require Adjustments after being installed on the tractor s front axle. Note: kit shown above is for the heavy duty two piece twelve bolt pattern front axle. Other types of front axles might require special parts. 18
19 Remove this bolt on right side of the differential housing on right side of front axle (JD-7920). You will use this same bolt for securing the wheel angle sensor bracket. 19
20 Mounting the wheel angle sensor bracket Steering cylinder Right side of front axle Mount the bracket in this position and secure with the original bolt. Torque the bolt to the tractor manufacturer specifications. 20
21 Mounting the tie rod bracket Tie rod (right side) Bolt Mount the bracket in the position shown above using the existing bolt & nut. Use the flat washer provided between the nut and the bracket. If the bolt is too short, replace with longer bolt of same grade. 21
22 Wheel angle Sensor Final Assembly & adjustments 1. Mount the wheel angle sensor and linkages as shown above 2. Connect the cable to the sensor (see cable identification figure in this manual) 3. Adjust the arm & rod lengths to obtain between 3400 and 3800 counts from the wheel angle sensor during steering calibration procedure 3. Check if wheel angle sensor has sufficient travel for hard left and hard right turns. 4. Tighten all nuts and bolts. 22
23 AutoSteer Valve Installation 23
24 AutoSteer Valve position Rotate Knob to open Remove this cover to gain access to mounting position for the AutoSteer valve 24
25 Valve Position on Tractor below right side of cab Rout the hydraulic hoses to front axle and steering unit through here Mount the valve bracket over this steel plate. Secure using three bolts. Use the back plate provided in your Kit behind the larger hole. You will have to drill one hole in tractor steel plate for the bolt on the Left. 25
26 AutoSteer Valve & mounting bracket Valve bracket Bolts & nuts AutoSteer Valve Backplate bracket 1. Mount the valve onto the bracket in the position shown using the three long 3/8 socket head screws provided. The screw heads must be mounted behind the bracket and the washers and nuts must be mounted over the front of the valve. The screw must not touch the fuel tank after assembly. 2. Mount the bracket onto the steel floor panel in front on the fuel tank under the right side of the tractor cab. 3. Secure the bracket onto existing holes on the steel floor panel using the bolts provided. Use the backplate to secure the bolt through the large hole on tractor. 4. Brackets shipped since 01/2005 use three mounting bolts and have an extra hole on the left side as shown. The bolt shown on the left requires drilling a 3/8 or larger diameter hole on tractor plate. 26
27 Installing the valve Bracket Bolt on left Is not shown Bolt the valve bracket to steel plate using three bolts. 27
28 Hose Connections on the AutoSteer Valve Connect to Left steer cylinder on front axle Connect to Right steer cylinder on front axle Connect to tractor steering unit on the port that sends oil to the Right steer cylinder (hose connector not shown) Connect to Load Sense port on tractor power beyond Connect to tractor steering unit on the port that sends oil to the Left steer cylinder Connect to Return (or tank) port on tractor power beyond Connect to Pressure port on tractor power beyond Connect the hydraulic hoses between the AutoSteer valve and the tractor steering system according to the connections shown above. 28
29 Valve Installed 29
30 Installing the Pressure Transducer Connector for cable Pressure transducer for detecting manual steering pressure ¼ NPT Elbow Adapter AutoSteer valve Install the pressure transducer in the position shown above. Use the 90 degree elbow adapter so that the pressure transducer is in a protected position close to the valve. Use Teflon tape on the threads to prevent oil leaks (you can use liquid thread sealer if you prefer). 30
31 Steering Hoses Installation 31
32 AutoSteer Hose Kit Identification Your AutoSteer installation kit is supplied with all the necessary hoses and adapters to complete the installation on the tractor. You will also change the position of two existing hoses on the tractor as part of your installation. P Pressure on tractor T Return on tractor Connect these ends to the AutoSteer valve at the ports identified as shown LS Load Sense on Tractor Connect these ends to tractor RIGHT Right steering cylinder on tractor Steer Out hoses LEFT Left steering cylinder on tractor Note: The steer in hoses going from the tractor steering unit to the AutoSteer valve will be the original hoses already installed on the tractor. You must disconnect the two hoses from the steer cylinder on the front axle and connected the same hose directly to the SL & SR ports on the AutoSteer valve. This feature allows us to use only five special AutoSteer hoses instead of the usual seven hoses. 32
33 Connecting Hoses to Power Beyond on Tractor Pressure Port (Metric M22 thread) Load Sense Port (Metric M12 thread) Return/Tank Port (Metric M22 thread) 1. The hydraulic oil supply for the AutoSteer valve is obtained from the Power Beyond ports on the tractor. 2. These ports must be already installed on the tractor before starting your AutoSteer installation. 3. Locate the power beyond ports at the back left side of the tractor as shown in picture above. 2. Install the metric hose adapters provided in your installation kit. Use metric Allen key tool to remove plugs. 3. Rout the three hoses (pressure/return/load sense) between the AutoSteer valve and the power beyond ports. 4. Connect the hoses to the power beyond outlets and the AutoSteer valve. 5. Secure the hoses with cable ties away from moving parts. 33
34 Steering Cable Identification Connect to pressure transducer & solenoids on AutoSteer valve Connect to Proportional (blue) valve on AutoSteer valve Connect to Wheel Angle Sensor On front axle Connects to Cab Box The steering cable sends electrical steering commands from the cab box to the main AutoSteer valve to turn the tractor wheels. Connect the cable between the cab box and the steering valve according to the connector identifications shown above. Rout the cable away from hot or moving parts and secure with cable ties. 34
35 Calibration and Tuning Notes Select Wheeled Tractor option during initial AutoSteer setup and calibration. Measure all the lever arm distances and input the values during AutoSteer setup and calibration procedure. If the hydraulic system is correctly installed and the pressure transducer has been calibrated, then the system should easily switch from AutoSteer Mode to Manual Steer Mode when you try to turn the steering wheel in AutoSteer mode. 35
36 AutoFarm NOVARIANT INC Willow Road Menlo Park/CA 36
AutoSteer Installation Guide
AutoSteer Installation Guide Covers AutoSteer (IK#180-0006-03 Rev A) installation on the following MFWD tractors: JD-8100 JD-8200 JD-8300 JD-8400 JD-8110 JD-8210 JD-8310 JD-8410 JD-8120 JD-8220 JD-8320
More informationAutoFarm GPS AutoSteer Hardware Installation Guide
AutoFarm GPS AutoSteer Hardware Installation Guide Supported Models: John Deere 7220 John Deere 7320 John Deere 7420 John Deere 7520 PN: 602-0022-02 Special Requirements Tools This list consists of special
More informationAutoFarm GPS AutoSteer Hardware Installation Guide
AutoFarm GPS AutoSteer Hardware Installation Guide Supported Models: Case AFX-8010 Combines PN: 602-0039-01-A Special Requirements Tools This list consists of special tools required to complete the installation.
More informationAutoFarm GPS AutoSteer Hardware Installation Guide
AutoFarm GPS AutoSteer Hardware Installation Guide Supported Models: Maxxum MXM-175 and MXM-190 MFD, New Holland TM-190, New Holland TM-175 PN: 602-0016-02-A Special Requirements Tools This list consists
More informationAutoFarm GPS AutoSteer Hardware Installation Guide
AutoFarm GPS AutoSteer Hardware Installation Guide Supported Models: Deutz 130 Agrotron, 140 Agrotron, 150 Agrotron, 165 Agrotron PN: 602-0046-01-A Special Requirements Tools This list consists of special
More informationAutoFarm GPS AutoSteer Hardware Installation Guide
AutoFarm GPS AutoSteer Hardware Installation Guide Supported Models: Deutz 215 Agrotron, 235 Agrotron, 265 Agrotron PN: 602-0047-01-A Special Requirements Tools This list consists of special tools required
More informationAutoFarm GPS AutoSteer Hardware Installation Guide
AutoFarm GPS AutoSteer Hardware Installation Guide Supported Models: Cat Challenger 65-E Track Cat Challenger 75-E Track Cat Challenger 85-E Track Cat Challenger 95-E Track PN: 602-0051-01-B i Special
More informationAutoFarm GPS AutoSteer Hardware Installation Guide
AutoFarm GPS AutoSteer Hardware Installation Guide Supported Models: John Deere 9120 Wheeled John Deere 9220 Wheeled John Deere 9320 Wheeled John Deere 9420 Wheeled John Deere 9520 Wheeled John Deere 9620
More informationSupported Models: Case SPX 3320 Case SPX 4410 Case SPX AutoFarm GPS AutoSteer. Hardware Installation Guide
Supported Models: Case SPX 3320 Case SPX 4410 Case SPX 4420 AutoFarm GPS AutoSteer Hardware Installation Guide P/N: 602-0150-01-A February 2008 Special Requirements Tools This list consists of special
More informationAutoSteer Installation Guide
AutoSteer Installation Guide John Deere JD-9860 STS Combine Harvester Covers AutoSteer (IK#180-0051-01 Rev A) installation on the following combine models having single cylinder rear axle: JD-9650 STS
More informationSupported Models: Ag-Chem Terragator 6103, 6203 Ag-Chem Terragator 8103, AutoFarm GPS AutoSteer. Hardware Installation Guide
Supported Models: Ag-Chem Terragator 6103, 6203 Ag-Chem Terragator 8103, 8203 AutoFarm GPS AutoSteer Hardware Installation Guide P/N: 602-0147-01-A January 2008 Special Requirements Tools This list consists
More informationKit. Hydraulic Kit Installation Guide REV B Table 1 Component List. Item Component Part Number Qty
Hydraulic Kit Installation Guide Table 1 Component List Item Component Part Number Qty 1. Hose 5/8 X 36-8F X -12F 90 DEG ORFS F451TC-JSJ9081210-36 2 2. HOSE ASSY. 1/4" X 36" -4F X -6F ORFS F451TC-JCJC040604-36
More informationKit. Hydraulic Kit Installation Guide REV A Item Component Part Number Qty
Hydraulic Kit Installation Guide Item Component Part Number Qty 1. HOSE 5/8 X 48" -8F X -12F 90 DEG ORFS F451TC-JSJ9081210-48 2 2. HOSE 1/4" X 48" -4F X -6F ORFS F451TC-JCJC040604-48 1 3. HOSE 5/8 X 72"
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual John Deere MFWD AutoTrac Ready Supported Models 8225R 8245R 8270R 8295R 8320R 8345R PN: 602-0254-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in
More informationKit. Hydraulic Kit Installation Guide REV A Item Description Part Number Qty
Hydraulic Kit Installation Guide Item Description Part Number Qty 1. HOSE ASSY. 1/2" X 174" -8F X -8F 90 DEG. ORFS F451TC-JCJ9080808-174 1 2. HOSE ASSY. 1/2" X 96" -8F X -10F ORFS F451TC-JCJC081008-96
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles Case IH Vehicles Case 5088 Combines Case 6088 Combines Case 7088 Combines Accuguide Ready PN: 602-0250-01-A LEGAL DISCLAIMER Note: Read and follow
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles John Deere Sprayers 4700 4710 4720 Non-AutoTrac Ready PN: 602-0228-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles Non-AccuGuide Ready and Non-IntelliSteer Ready Case STX Wheeled or Quadtrac Case STEIGER Wheeled or Quadtrac New Holland TJ New Holland T 380
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual John Deere MFWD Valve Install Vehicles Supported Models 7200 7210 7400 7410 7600 7510 7700 7610 7800 7710 7810 PN: 602-0212-01-A LEGAL DISCLAIMER Note: Read and
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Closed Center High Flow Valve Custom Hardware Installation Guidelines and Recommendations THIS MANUAL IS FOR TRAINED AUTOSTEER DEALERS ONLY PN: 602-0203-01-A LEGAL
More informationA5 AutoSteer Closed Center Compact Valve Custom Hardware Installation Guidelines and Recommendations
A5 AutoSteer Closed Center Compact Valve Custom Hardware Installation Guidelines and Recommendations THIS MANUAL IS FOR TRAINED AUTOFARM DEALERS ONLY AutoFarm GPS AutoSteer Hardware Installation Guide
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles Case IH Vehicles Case 2577 Combines Case 2588 Combines Accuguide Ready PN: 602-0233-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles Agco Gleaner Combines R65 R66 R75 R76 PN: 602-0288-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual carefully before
More informationINSTALLATION MANUAL. AutoSteer Install Kit: AutoTrac Ready Installation
INSTALLATION MANUAL AutoSteer Install Kit: 186-0002-01 186-0002-02 186-0002-03 186-0002-04 Please refer to this manual prior to beginning the installation of the AutoSteer system AutoTrac Ready Installation
More informationWheel Angle Sensor Kit Installation
Wheel Angle Sensor Kit Installation Item Component Part Number Qty 1. Bracket Kit, WAS 200-0081-02 1 2. WAS Assembly 200-0468-01 1 3. Instruction Guide 602-0398-01 1 602-0398-01 REV A 2014-02 Overview
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles Case STX Wheeled or Quadtrack Case STEIGER Wheeled or Quadtrack New Holland TJ New Holland T 380 380 380 9030 430 385 430 9040 480 430 480 9050
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles Case IH Combines 7010 7120 8010 8120 AFX 8010 9120 PN: 602-0283-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual carefully
More informationKit. Hydraulic Kit Installation Guide REV A. Item Component Part Number Qty
Hydraulic Kit Installation Guide Item Component Part Number Qty 1. HOSE ASSY. 3/8" X 110" -8F ORFS X -8F ORFS 90 DEG F451TC-JCJ9080806-110 1 2. HOSE ASSY. 3/8" X 110" -6F ORFS X -8F ORFS 90 DEG F451TC-JCJ9060806-110
More informationAutomated Steering Hydraulic Installation Kit
Automated Steering Hydraulic Installation Kit P/N: ED-JD4060 Fits John Deere Tractor Models: 4560 4760 4960 Overview A series of equipment specific hydraulic installation kits have been developed to work
More informationInstallation Manual. AutoSteer. Gleaner Combine. AutoGuide 2 Steer Ready. Supported Models A66 A76 R66 R76 S67 S77 PN: A
Installation Manual AutoSteer Gleaner Combine AutoGuide 2 Steer Ready Supported Models A66 A76 R66 R76 S67 S77 PN: 602-0312-01-A LEGAL DISCLAIMER Note: Read and follow ALL Instructions in this manual carefully
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles New Holland Combines CR 9040 CX 9040 CR 9050 CX 9050 CR 9060 CX 9060 CR 9070 CX 9070 CR 9080 CX 9080 IntelliSteer Ready PN: 602-0231-01-A LEGAL
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual John Deere Track Supported Models 8295RT 8320RT 8345RT PN: 602-0255-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual carefully before
More informationKit. Hydraulic Kit Installation A. Item Component Part Number Qty
Hydraulic Kit Installation Item Component Part Number Qty 1. 2. 3. 4. Hose, 1/2 x 60-8F ORFS x -8F ORFS 90 Hose, 3/8 x 60-6F ORFS x -8F ORFS 90 Hose, 1/4 x 60-4F ORFS x -4F ORFS 45 Hose, 1/4 x 60-4F ORFS
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles MacDon M150 M200 PN: 602-0232-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual carefully before installing or operating
More informationAutomated Steering Hydraulic Installation Kit
Automated Steering Hydraulic Installation Kit P/N: ED-JD7010 its John Deere Tractor odels: 7200 7210 7400 7410 7510 7600 7610 7700 7710 7800 7810 Overview A series of equipment specific hydraulic installation
More informationINSTALLATION MANUAL. Fendt VarioGuide Ready COM 3 Supported Models PN REV A
INSTALLATION MANUAL Fendt VarioGuide Ready COM 3 Supported Models 922 924 927 930 933 936 PN 602-0264-02 REV A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual carefully before installing
More informationPN: A. Reactive Steering Kit Installation Manual
PN: 602-0275-01-A Reactive Steering Kit Installation Manual LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual carefully before installing or operating the AutoSteer system. Note: Take
More informationJanuary Rev. B Rel. 2
Automated Steering Hydraulic Installation Kit P/N: ED-JD4040 Fits John Deere Tractor Models: 4050 4055 4250 4255 4440 4450 4455 4555 4640 4650 4755 4840 4850 4955 Overview A series of equipment-specific
More informationWheel Angle Sensor Kit Installation
Wheel Angle Sensor Kit Installation Item Component Part Number Qty 1. Bracket Kit, WAS, Titan 200-0769-01 1 2. WAS Assembly 200-0468-01 1 3. Instruction Guide 602-0576-01 1 602-0576-01 Rev A Overview Always
More informationINSTALLATION MANUAL. AutoSteer. Install Kit: Upgrade from A5
INSTALLATION MANUAL AutoSteer Install Kit: 186-0066-01 Please refer to this manual prior to beginning the installation of the AutoSteer system Upgrade from A5 Custom Hardware Installation 2014-05 PN 602-0432-02
More informationAutomated Steering Hydraulic Installation Kit
Automated Steering Hydraulic Installation Kit P/N: ED-MF0 Fits Massey Ferguson Swather Models: 0 Read and Follow Safety Messages In these instructions, you will see the heading, WARNING, and the safety
More informationGPS Steering System Installation Manual
GPS Steering System Installation Manual Supported Vehicles Challenger Massey Ferguson AGCO MT-645C, MT-645D MF-8650 DT-205B MT-655C, MT-655D MF-8660 DT-225B MT-665C, MT-665D MF-8670 DT-250B MT-675C, MT-675D
More informationFits AGCO, Challenger, & Massey Ferguson Tractor Models:
Automated Steering Hydraulic Installation Kit P/N: ED-MF8400 Fits AGCO, Challenger, & Massey Ferguson Tractor Models: DT180A MT635B 8450 DT200A MT645B 8460 DT220A MT655B 8470 DT240A MT665B 8480 Overview
More informationOpen Center Compact Valve Custom Installation Guide Rev A
200-0762-01 Open Center Compact Valve Custom Installation Guide 602-0575-01 Rev A 2014-12 Overview This guide provides information for completing a custom AutoSteer valve installation on wheeled farm vehicles
More informationAutoFarm AutoSteer System Installation, Calibration & Tuning Guide
AutoFarm AutoSteer System Installation, Calibration & Tuning Guide Model: John Deere 8000 Series Tracked Tractor PN: 602-0002-01 Rev A April 21, 2004 Purpose: This document guides certified field technicians
More informationINSTALLATION MANUAL. Install Kit: AutoTrac Ready Installation
INSTALLATION MANUAL Install Kit: 188-0089-02 Please refer to this manual prior to beginning the installation of the ParaDyme system AutoTrac Ready Installation Supported Models. John Deere S680 S690 2013-05
More informationWheel Angle Sensor Kit Installation
Wheel Angle Sensor Kit Installation Item Component Part Number Qty 1. WAS Bracket Kit 200-0247-02 1 2. WAS Assembly Kit 200-0468-01 1 3. Instruction Guide 602-0401-01 1 602-0401-01-A Overview Always shut
More informationWheel Angle Sensor Kit Installation
Wheel Angle Sensor Kit Installation Item Component Part Number Qty 1. Bracket Kit, WAS 200-0540-01 1 2. WAS Assembly 200-0468-01 1 3. Instruction Guide 602-0390-01 1 602-0390-01 REV A 2014-02 Overview
More informationINSTALLATION INSTRUCTIONS Autopilot Kit
INSTALLATION INSTRUCTIONS Autopilot Kit MODELS Case IH MX20 MX230 MX255 MX285 Note: This kit is to be installed by a Trimble-trained technician only. 2004 Trimble Printed in U.S.A. 40394-25-AP Issued 2/04
More informationWheel Angle Sensor Kit Installation
Wheel Angle Sensor Kit Installation Item Component Part Number Qty 1. Bracket Kit, WAS 200-0572-01 1 2. WAS Assembly 200-0468-01 1 3. Instruction Guide 602-0456-01 1 602-0456-01-A Overview Always shut
More informationWheel Angle Sensor Kit Installation
Wheel Angle Sensor Kit Installation Item Component Part Number Qty 1. Bracket Kit, WAS 200-0535-01 1 2. WAS Assembly 200-0468-01 1 3. Instruction Guide 602-0467-01 1 602-0467-01-A Overview Always shut
More informationAutomated Steering Hydraulic Installation Kit
Automated Steering Hydraulic Installation Kit P/N: ED-AC85496 Fits Ag-Chem RoGator Sprayer: 854 (Models thru 1996) Overview A series of equipment-specific hydraulic installation kits has been developed
More informationONBOARD AIR SYSTEM FOR ALL VEHICLES APPLICATIONS
ONBOARD SYSTEM FOR ALL VEHICLES APPLICATIONS Thank you and congratulations on the purchase of a Pacbrake onboard air system. Please read the manual prior to starting to ensure you can complete the installation
More informationIMPORTANT! READ BEFORE INSTALLING!
1360 Redwood Way, Suite A Petaluma, CA. 94954 TEL: (707) 763-7799 Toll free in the USA (800) 767-9543 FAX (707) 763-2631 www.xandexsemi.com EMAIL: info@xandex.com Instructions for Xandex Pneumatic Controller
More informationRECON ZONE BLOCKAGE AND FLOW MONITOR INSTALLATION MANUAL. Document revision: 1.2 Last revised: October 25, 2017
RECON ZONE BLOCKAGE AND FLOW MONITOR INSTALLATION MANUAL Document revision: 1.2 Last revised: October 25, 2017 Recon Zone Blockage and Flow Monitor Installation Manual 2017 Intelligent Agricultural Solutions.
More informationAssisted Steering Hydraulic Installation Manual for Vehicle Kit Number Fits Only AGCO Gleaner R62/R65 (after S/N 66000) and R72/R75 (after
F i e l d p i l o t U s e r M A N U A L Assisted Steering Hydraulic Installation Manual for Vehicle Kit Number 91-02340 Fits Only AGCO Gleaner R62/R65 (after S/N 66000) and R72/R75 (after S/N 76000) Combines
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE 3000 SERIES (4200/4300/4400) (4210/4310/4410) & (3120/3320/3520/3720) HARD SIDED CAB ENCLOSURE (p/n 1JD3520AS) SOFT SIDED CAB ENCLOSURE
More informationClutch Control. PN: November 2013 Rev E 1
NOTE: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Module Kit 4100533 1 Cable Installation Kit 2000901-1 1 Alcohol swab packet 2002811 2
More informationSprayer Control. Manual for SprayLink Cable Installations. Tank. Jet Agitator. Agitator Valve. Diaphragm Pump. Pressure Transducer.
Sprayer Control Plumbing & Installation Manual for SprayLink Cable Installations Tank Jet Tank Shut-Off Diaphragm Pump Electric Ball s Transducer Strainer Relief Regulating Copyrights 2012 TeeJet Technologies.
More informationFAX
INSTALLATION INSTRUCTIONS 6090 Air Suspension Kit (pat. pending) 1999-2006 Tahoe, Suburban, Avalanche, Yukon Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY
More informationREARVIEW MIRROR AND BACKUP CAMERA KIT
REARVIEW MIRROR AND BACKUP CAMERA KIT P/N 2881483 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for.
More informationZONE BLOCKAGE AND FLOW MONITOR INSTALLATION MANUAL
ZONE BLOCKAGE AND FLOW MONITOR INSTALLATION MANUAL Document revision: 1.1 Last revised: February 24, 2017 Zone Blockage and Flow Monitor Installation Manual 2017 Intelligent Agricultural Solutions. All
More informationVALVE AND PLUMBING KIT NEW HOLLAND 7310 LOADER NEW HOLLAND TRACTORS
ASSEMBLY MANUAL Keep With Operator s Manual VALVE AND PLUMBING KIT NEW HOLLAND 73 LOADER NEW HOLLAND TRACTORS MODEL 2WD FWA LESS CAB WITH CAB TT55 X X X TT75 X X X Valve and plumbing kit can be installed
More informationTOYOTA TACOMA XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-35090 Tuner Assembly 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item
More informationEndeavor Fertilizer Controler" Electric Pump Fertilizer System for John Deere GS2 with Servo Control
Endeavor Fertilizer Controler" Electric Pump Fertilizer System for John Deere GS with Servo Control We Can Also Interface with These Popular Third Party Controllers: Trimble - EZ Boom & Field IQ Ag Leader
More informationSCION xb SIRIUS SATELLITE RADIO TUNER Preparation
Preparation Part Number: PTS3-52050 NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Reqd. Description Antenna, Exterior 2 Wire Harness 3 Bracket,
More informationECU Mounting Bracket Installation
ECU Mounting Bracket Installation Item Component Part Number Qty 1. Bracket, ECU Mounting 202-0481-08 1 2. Instruction Guide 602-0359-02 1 3. Screw, 8-32 x 1/2 Hex 514-0151-01 4 4. Bolt, M6 x 1 x 25mm
More informationAutomatic Electronic Sport Mode Shifter Installation Instructions
Automatic Electronic Sport Mode Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Release Automatic Electronic Sport Mode
More informationSteer Ready Kit Installation Guide
Fits Caterpillar Challenger MT Track Tractor Models: 745 755 765 835 845 855 865 875 745B 755B 765B 835B 845B 855B 865B 875B Steer Ready Kit Installation Guide Kit: EDX-SR-CATMTT, P/N 911-3005-000 Read
More informationSteer Ready Kit Installation Guide
Fits CaseIH Tractors: Puma 130 Puma 200 Puma 145 Puma 215 Puma 160 Puma 230 Puma 170 Puma 185 Steer Ready Kit Installation Guide Kit: EDX-SR-CPuma, P/N 911-3016-000 Read and Follow Safety Messages In these
More informationCombustion Technologies By-Pass Filtration Instructions
Combustion Technologies By-Pass Filtration Instructions www.combustionusa.com Made in the USA Date Revision Jan 17 th, 2013 PLEASE READ AND UNDERSTAND ALL INSTALLATION INSTRUCTIONS PRIOR TO BEGINNING THE
More informationPowerglide Automatic Floor Mount Shifter Installation Instructions
Powerglide Automatic Mount Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 (865) 966-2269 FAX (865) 671-1999 tech@lokar.com www.lokar.com Powerglide
More informationJohn Deere. MODEL: 2140 Volume 1 of 3 JD-S-TM4373
John Deere MODEL: 2140 Volume 1 of 3 THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF JOHN DEERE OR IT'S SUCCESSORS. JOHN DEERE AND IT'S SUCCESSORS ARE NOT RESPONSIBLE FOR THE QUALITY
More information6 Gauge Box Set IS0332
Caution 6 Gauge Box Set IS0 Rev. A ecr 878 /0 Disconnect the battery during installation. Tighten nuts on the back clamp only slightly more than you can tighten with your fingers. Six inch-pounds of torque
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08L92-S0X-100 ODYSSEY AII 22049 Issue Date AUG 2000 PARTS LIST Trailer hitch Receiver cover 2 Small wire ties (1 not used) Ball mount
More informationVALVE AND PLUMBING KIT 2408TL LOADER AGCO & MASSEY FERGUSON TRACTORS
ASSEMBLY MANUAL Keep With Operator s Manual VALVE AND PLUMBING KIT 2408TL LOADER AGCO & MASSEY FERGUSON TRACTORS AGCO MASSEY FERGUSON CAB ROPS ST34A 1533 X ST41A 1540 N/A X TRACTOR AND VALVE KIT GENERAL
More informationInstallation. Manual. OnTrac2+ GPS Assisted Steering System PN: A
Installation OnTrac2+ GPS Assisted Steering System Manual PN: 602-0208-02-A Copyright Copyright 2012. All rights reserved. This document is copyrighted and all rights are reserved. Information in this
More informationGOCATUTV.COM Hydraulic Brake line Lock for UTV / Side by Sides
GOCATUTV.COM Hydraulic Brake line Lock for UTV / Side by Sides WARNING! Hydraulic Brake line locks are intended to supplement park brake locks and should only be used in conjunction with your factory park
More informationFord C6 Automatic Trans Mount Shifter Installation Instructions
Ford C6 Automatic Trans Mount Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Ford C6 Automatic Trans Mount Installation
More informationgeneral booster conversion kit instructions
general booster conversion kit instructions your kit may look slightly different than above instructions are general and work for many builds Unboxing your kit: 1. Remove new booster, bracket assembly
More informationAIRTEK for Mack Vehicles Single to Dual Height Control Valve Conversion Kit
Single to Dual Height Control Valve Conversion Kit SUBJECT: Kit Nos.60961-128 and 60961-129 LIT NO: 59310-030 DATE: April 2006 REVISION: A INTRODUCTION As of March 2006 all of Mack vehicles will be equipped
More informationHP10207 KIT. Ram WD*
HP10207 KIT Ram 1500 4WD* (For 2WD call customer service 800.663.0096 for assistance) * See application guide for proper fitment. Use the most advanced air springs on the market to eliminate your vehicle
More informationRZR WINCH KIT KIT P/N
RZR WINCH KIT KIT P/N 2878787; 2879334 Application All RZR Models except RZR XP Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain
More informationToyota 4RUNNER With/MR Overhead Video
Toyota 4RUNNER With/MR 2010-10.2 Overhead Video Part Number: 00016-00110; Fit Kit-00110-14, Beige 00016-00120; Fit Kit-00120-14, Gray Accessory Code: ED7 Conflicts: Vehicles without a sunroof Kit Contents:
More informationTOYOTA Matrix XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-12080 Tuner Assembly 86180-0W031 (Music Only) Tuner Assembly PT546-00090 (Music Plus Data) NOTE: Part number of this accessory may not be the same as the part
More informationVALVE AND PLUMBING KIT INSTRUCTIONS SMC 84Q & 2408 LOADERS NEW HOLLAND TRACTORS MODEL 2WD 4WD LESS CAB WITH CAB 1720 X X X 1920 X X X
ASSEMBLY MANUAL Keep With Operator s Manual VALVE AND PLUMBING KIT INSTRUCTIONS SMC 84Q & 2408 LOADERS NEW HOLLAND TRACTORS MODEL 2WD 4WD LESS CAB WITH CAB 1720 X X X 1920 X X X TRACTOR AND VALVE KIT GENERAL
More informationInstallation Instructions
Part # 500399-00 Up Camaro Level 3 Shockwave System Front Components: 30 Front ShockWave Strut Recommended Tools Rear Components: 505 Rear ShockWave Miscellaneous Components: 303000 3 Gallon AirPod Compressor
More informationConstruction Attachments, Inc. Auxiliary Hydraulics
Construction Attachments, Inc. Auxiliary Hydraulics D03 KIT WITHOUT HOSES FOR TRACTOR WITH LESS THAN 14GPM OPEN CENTER HYDRAULIC SYSTEM AND A FACTORY OR AFTERMARKET 2 FUNCTION LOADER VALVE BEFORE INSTALLING
More informationAIRTEK for Volvo Vehicles Single to Dual Height Control Valve Conversion Kit
Single to Dual Height Control Valve Conversion Kit SUBJECT: 60961-101 and 60961-102 LIT NO: 59310-026 DATE: January 2006 REVISION: A INTRODUCTION Prior to March 2005, some Volvo vehicle configurations
More informationInstallation Instructions
Powerglide Automatic Trans Mount Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 (865) 966-2269 FAX (865) 671-1999 tech@lokar.com www.lokar.com Powerglide
More informationINSTALLATION MANUAL. Agra-GPS Fendt-JD Bridge for Fendttractors
INSTALLATION MANUAL Agra-GPS Fendt-JD Bridge for Fendttractors Version 1.0 Revision A January 2016 Contact information Agra-GPS Ltd. Box 2585 Stony Plain, AB T7Z 1X9 CANADA 001 780 990 4052 Phone www.agra-gps.com
More informationROGATOR B RAVEN RS1 ISO GUIDANCE AND STEERING INSTALLATION GUIDE
ROGATOR B RAVEN RS1 ISO GUIDANCE AND STEERING INSTALLATION GUIDE ROGATOR B RAVEN RS1 ISO GUIDANCE AND STEERING INSTALLATION GUIDE This quick guide provides the installation instructions for the RS1 on
More informationDeegan 38 HD Rock Sliders w/ LED Rock Lights (07-18 Wrangler JKU)
Installation Time: 2-3 Hours Deegan 38 HD Rock Sliders w/ LED Rock Lights (07-18 Wrangler JKU) Note: This kit comes with everything you need to wire the lights with a switch in the cab. However, I recommend
More informationInstallation Instructions Diesel Nitrous System (#82028)
Installation Instructions Diesel Nitrous System (#82028) Thank you for choosing ZEX. If at any time you have questions regarding this or any of our products, please call our Nitrous Help support line at
More informationTOYOTA PRIUS XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-4700 Tuner Assy 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item # Quantity
More informationFRS/BRZ Air Oil Separator (AOS) Installation Manual
FRS/BRZ Air Oil Separator (AOS) Installation Manual Eric Hazen Rev. 2 Overview: Detailed instructions on installing the AOS for the FRS/BRZ/GT86. Difficulty: Beginner Time required: 1-3 hours depending
More informationPerfect Park 7000 Installation & Unloading Instructions Operating Manual
Perfect Park 7000 Installation & Unloading Instructions Operating Manual 1) Always file a claim with the truck line if the lift has been damaged! (If you don t originally notice the damage, but find some
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE 4000 SERIES (4500/4600/4700) (4510/4610/4710) (4120/4320/4520/4720) HARD SIDED CAB ENCLOSURE (p/n 1JD4120AS) SOFT SIDED CAB ENCLOSURE
More informationBasic Machine Interface Options
Limit Switch Version (515) 232-3188 www.razorgage.com Basic Machine Interface Options The Tool Safe Sensor is a limit switch to be installed on the user s saw, drill press, punch press, or whatever the
More informationServo and Proportional Valves
Servo and Proportional Valves Servo and proportional valves are used to precisely control the position or speed of an actuator. The valves are different internally but perform the same function. A servo
More information