Innovative Technologies for Roadside Maintenance. Product Range Mowing. Municipal Tractors

Transcription

1 Innovative Technologies for Roadside Maintenance Product Range Mowing Municipal Tractors

2 The complete overview on Reflexion post mowers / Verge mowers Front-mounted mowing equipment MLM 200 / MRM 300 MRS 300 MFK 400 Control Drive MLM 200 up to 2.5 m MRM 300 up to 3.0 m The Reflexion post mower MLM 200 works around the guard rails, posts and traffic signs. In combination with the verge mower MRM 300 it offers a very effective and economic solution. Mowing combinations electro-hydraulical Front PTO-shaft (opt. rear PTO-shaft with rear-mounted hydraulic) - Automatic touch control system to adapt to the terrain contour - Continuous distance control to the guard rail MKF 600 MLM 200 / MRM 300 transport up to 3 m right-/left-hand side Drive The verge mower MRS 300 is perfect for close to roadside mowing work, either righthand or left-hand operation. Due to its low height, this mower is suitable for use underneath crash-barriers. Front PTO-shaft (opt. rear PTO-shaft with rear-mounted hydraulic) - Electro-hydraulic control with mowing head relief system - Road speed-related automatic obstacle detector - Automatic parking system MRS 300 transport MKM 700 up to 5.1 m right-/left-hand side 1500 mm - Transport position in front of the vehicle - Width in transport position 2.1 m - Universal use by quick-changedevice - for small tractors The MFK 400 has been designed for smaller size of tractors and vehicles and is an ideal basis for cost effective road side maintenance. Various available working attachments for the MFK 400, guaranty a multipurpose use of the arm the whole year long. MFK 400 transport Central-mounted mowing equipment GZA 500 SM Front-mounted mower 5.5 m / 6.0 m* (with telescopic arm 6.5 m / 7.0 m*) Verge mower 3.0 m The independent lateral shift of power arm and verge mower increases the working performance considerably, in particular when working in alleys and under crash barriers. The MKF 600 has a compact transport position. hydraulic, 1300 mm (1800 mm*) Verge mower up to 1000 mm - Transport width 2.5 m - CAN-Bus control / Mähtronic and automatic touch control system MKF 600 transport * after dismounting of the verge mower The optimal geometry of the boom system makes it easy for the MKM 700 to avoid obstacles such as traffic signs up to 2.9 m and enables quick mowing work. Front-mounted mower 6.7/6.9* m (7.2/7.4* m)** Verge mower 3.0 m 850 mm (1300 mm**) - Proportional control with CAN-Bus - Automatic parking / extending of the verge mower - Automatic touch control and arm relief system Mähtronic MKM 700 transport * with overhead offset cylinder ** after dismounting of the verge mower up to 6.8 m Swivel range 180 (90 rear / 90 front) Mounting Transport position Centre position Each boom available with telescopic arm function. That makes it possible to set up the GZA 500 for flexible use and for the best reach suitable for almost all sizes of tractors. over fender to the rear GZA 500 SM transport

3 professional roadside care. MFK 500 FME 500 FME 600 up to 6 m right-/left-hand side (with telescope up to 7 m) 1800 mm - Transport position in front of the vehicle (equipment width in transport position 2.4 m) - Universal use by quick-changedevice up to 6.5 m right-/left-hand side - Transport position above vehicle cab - Low front axle load in transport position - Implement width in transport position only 1.5 m up to 7.2 m right-/left-hand side 1300 mm - Balanced weight distribution in transport position - Obstacles easily passed - Implement width in transport position only 2.1 m Thanks to its lateral shift and its geometry the MFK 500 is suitable for mowing and working close to the roadside as well as behind crash barriers. An optional telescopic arm increases its reach, e.g. for hedge cutting. MFK 500 transport The FME 500 with its reach up to 6.50 m is parked in transport position at the rear behind the cab on a parking frame. This configuration provides a balanced weight distribution on the vehicle axles. FME 500 transport The lateral shift of the FME 600 makes the arm highly flexible in every field of activity. Thanks to the special arm geometry it is easy to work with, has considerable reach and passes obstacles with ease. FME 600 transport GZA 750 S / 850 S Rear-mounted mowing equipment GA 600 GHA 600 P Swivel range Mounting Transport position up to 7.0 m / 8.0 m (with telescopic arm 8.2 / 9.2 m) right-hand working position 200 (95 rear / 105 front) Centre position over fender to the rear Working in the immediate proximity of obstacles is now possible with the integrated swivel arm. Transport position to the rear allows advanced driver s view on the street while driving. GZA 750 S with Telesc. transport Mounting Transport position up to 6.4 m right-/left-hand side (with telescopic 7.4 m) rear position above power-lift unit over cabin to the front With the high mounting position it is possible to work over high obstacles. GA 600 transport (Parallelogram boom) up to 6.0 m Displacement up to 2.5 m Various range of working attachments extending the use for the GHA 600 P. Displacement of the mowing head by the parallelogram arm geometry increases the operators comfort. The GHA 600 P is easily mounted in the three point linkage. - Proportional control and ergonomically one hand joystick - Works ideally in combination with front mounted verge mower - Automatic touch control and arm relief system Mähtronic (opt.) GHA 600 P transport measures from the center of the vehicle (including mowing head width of 1.2 m)

4

5 Optional features for MULAG-Mowers Mähtronic Hydraulic Rotating Device Multifunction Joystick Automatic, computer-assisted contact pressure setting of the mowing head. Sensors transmit the ground configuration to the computer which adjusts the boom functions independently. The rotational range is 230, continously controlled via the control unit. The rotational range can be adapted during operation. The form of this joystick is perfectly adapted to the human hand. Up to 4 proportional functions can be controlled at one level. Rear-mounted Hydraulics Front-mounting plate Axle Support To drive front-mounted power arms with the rear PTO-shaft a supporting frame for the hydraulic drive has to be build onto the rear power-lift unit. One or more hydraulic pumps are driven by a cardan shaft. The supporting frame serves also as a support for mounting the hydraulic tank, optional counterweights and the parking frame for power arms with transport position above the cabin. For the mechanical support of front-mounted power arms a front-mounting plate (size 3) is being attached to the tractor front. This frontmounting plate is installed onto the front power-lift unit with the lower links removed. Thus an easy accessible and robust base for the front-sided mounting of the power arm is being accomplished. To reinforce the vehicle against torsional moments alongside the vehicle axis it is necessary to install a hydraulic cylinder with disengageable support to the vehicle front axles. The hydraulic supply of the support is realized using the existing vehicle hydraulics. Depending on the application of the power arm the support on the vehicle axle can be single- or doublesided.

6 Working attachments for operation all year round Mowing Heads Flail Head Universal Cutting Head Scrub Cutting Head Clearing attachments Verge Cleaning Device Rotary Ditch Cleaner MK 1200 / 1600 Mowing of grass and scrub Working width 1200 / 1600 mm Cutting thickness 20 / 20 mm approx. 320/ 385 kg UMK 1200 Mowing of grass and scrub Working width 1200 mm Cutting thickness up to 40 mm approx. 350 kg GMK 1200 Mowing of grass and scrub Working width 1200 mm Cutting thickness up to 60 mm approx. 345 kg BRG 1000 Cleaning of overgrown verges Working width 1000 mm Cutting thickness up to 80 mm approx. 415 kg GRG 650 Clearing of roadside ditches Ø Milling wheel 650 mm Wheel speed 500 rpm approx. 245 kg Attachments for hedging and siding up Coarse Cutting Bar Branch / Hedge Cutter Free Zone Cutter Stump Grinder Earth Auger Earth Auger GMB 2000 Cutting of branches, twigs, etc. Working width 2000 mm Cutting thickness 40 mm approx. 135 kg Brush systems Weed Brush WKB 750 Removing of grass and weeds Working width 750 mm Brush speed 300 rpm approx. 140 kg AWS 2200 Cutting of branches, twigs, etc. Working width 2200 mm Cutting thickness 110 mm approx. 210 kg Gutter / Surface Brush RB 650 Removing of grass and weeds Working width 500 mm Ø Brush 650 mm approx. 160 kg FSG 2000 Clearing of walkways / roadsides Working width 2000 mm Cutting thickness up to 150 mm approx. 220 kg Double Washing Brush DWB Washing of posts, road signs, etc. Working width 800 mm Ø Brush 600 mm approx. 200 kg BSF 500 Grinding stumps (e.g. along roadsides) Ø Grinding wheel 500 mm Rate of cut max. 40 mm approx. 170 kg EBG drilling of holes (for posts e.g.) Auger length 900 mm Ø Auger 250 mm approx. 165 kg Embankment maintenance Double Blade Cutter Weed Bucket DSW 1900 Grass / shrub removal on slopes Working width 1900 mm Cutting thickness up to 10 mm approx. 130 kg MKB 2450 Clearing of ditch vegetation Working width 2450 mm Stroke rate max. 600 per minute approx. 235 kg MULAG Fahrzeugwerk Heinz Wössner GmbH u. Co. KG // Subject to change without notice, Dok 0215_333en * other working attachments on demand Distributor Manufacturer MULAG Fahrzeugwerk Heinz Wössner GmbH u. Co. KG Gewerbestraße Oppenau Germany Phone Fax info@mulag.com Web