TR-800XXL Ton Capacity (72.6 Metric Tons) DIMENSIONS. GENERAL DIMENSIONS (29.5 X 25 Tires) 46' 8-1/4" (14230) 6' 7/8"(1850)

Transcription

1 TR-8XXL-4 8 Ton Capacity (72.6 Metric Tons) HYDRAULC ROUGH TERRAN CRANE DMENSONS 13' 6-1/4" (412) 46' 8-1/4" (1423) Min. 37' 8-3/4" ~ Max. 144' 4-1/4" (115 ~ 44) 6' 7/8"(185) 11' 4-1/2" (347) 12' 5-1/2" (38) 9' 2-1/4"(28) 18' 1/2"(55) 21' 11-3/4"(67) 23' 7-1/2"(72) 17.6 o 14.4 o 6' 7-3/4"(225) 12' 11-1/2"(395) 23' 7-1/3" (72) 6' 1-7/8"(1875) 7' 1-1/2"(24) GENERAL DMENSONS (29.5 X 25 Tires) Feet Meters Turning radius 4 wheel steer 21' 11-3/4" wheel steer 39' 1/2" ' 2-1/2" (252) 1' 1-1/2" (15) 1 Specifications are subject to change without notice

2 SUPERSTRUCTURE SPECFCATONS BOOM DRUM - Grooved 15-3/4"(.4m) root diameter x 22-3/4" Five section full power synchronized telescoping boom, (.578m) wide. Wire rope: 436' of 3/4"diameter rope (1m of 37.7'~144.4'(11.5m~44.m), of round hexagonal box construction 19mm). Drum capacity: 1,96' (4m) 7 layers. Maximum line with 7 sheaves, 17-5/16" (.44m) root diameter, at boom head. pull (available): 18,2lbs. (8,26kg). Maximum line speed: The synchronization system consists of two double acting telescope 585FPM (178m/min). cylinders, an extension cable and retraction cable. Hydraulic cylinder fitted with holding valve. Two easily removable wire rope guards, WRE ROPE - Warrington seal wire, extra improved plow steel, rope dead end provided on both sides of boom head. Boom preformed, independent wire rope core, right regular lay. telescope sections are supported by wear pads both vertically and 3/4"(19 mm) 6X37 class horizontally. Extension speed 16' 7-1/2" in 145 seconds. HOOK BLOCKS 6.2 ton (5.6 metric ton) - Weighted hook with swivel and BOOM ELEVATON - By a double acting hydraulic cylinder safety latch, for 3/4"(19mm) wire rope. with holding valve. Elevation -2. o ~8.7 o, combination controls for hand or foot operation. Boom angle indicator. HYDRAULC SYSTEM Automatic speed reduction and soft stop function. Elevation speed -2. o ~8.7 o in 77 seconds. PUMPS - Two variable piston pumps for crane functions. Tandem gear pump for steering, swing and optional equipment. JB - Two stage bi-fold lattice type with 3.5 o, 25 o or 45 o offset Powered by carrier engine. Pump disconnect for crane is (tilt type). Single sheave, 15-5/8"(.396m) root diameter, at the engaged/ disengaged by rotary switch from operator's cab. head of both jib sections. Stored alongside base boom section. Jib length is 32.5' (9.9m) or 58.1' (17.7m). Assist cylinders for CONTROL VALVES - Multiple valves actuated by pilot mounting and stowing are controlled at right side of superstructure. pressure with integral pressure relief valves. Self stowing jib mounting pins. RESERVOR gallon (74 lit.) capacity. External sight AUXLARY LFTNG SHEAVE (SNGLE TOP) level gauge. Single sheave, 15-5/8"(.396m) root diameter. Mounted to main boom head for single line work (stowable). FLTRATON - 26 micron return filter, full flow with bypass protection, located inside of hydraulic reservoir. Accessible for ANT-TWO BLOCK - Pendant type over-winding cut out easy replacement. device with audio-visual (FALURE lamp/buzzer) warning system. OL COOLER - Air cooled fan type. SWNG Hydraulic axial piston motor driven through planetary swing speed reducer. Continuous 36 o full circle swing on ball bearing turntable at 2.3rpm. Equipped with manually locked/released swing brake. A 36 o positive swing lock for pick and carry and travel modes, manually engaged in cab. Twin swing System: Free swing or lock swing controlled by selector switch on front console. HOST MAN HOST - Variable speed type with grooved drum driven by hydraulic axial piston motor through winch speed reducer. Power load lowering and raising. Equipped with automatic brake (neutral brake) and counterbalance valve. Controlled independently of main hoist. Equipped with cable follower and drum rotation indicator. DRUM - Grooved 15-3/4"(.4m) root diameter x 22-3/4" (.578m) wide. Wire rope: 797' of 3/4"diameter rope (243m of 19mm). Drum capacity: 1,96' (4m) 7 layers. Maximum line pull (available): 18,2lbs. (8,26kg). Maximum line speed: 585FPM (178m/min). AUXLARY HOST - Variable speed type with grooved drum driven by hydraulic axial piston motor through winch speed reducer. Power load lowering and raising. Equipped with automatic brake (neutral brake) and counterbalance valve. Controlled independently of main hoist. Equipped with cable follower and drum rotation indicator. CAB AND CONTROLS Both crane and drive operations can be performed from one cab mounted on rotating superstructure. Left side, 1 man type, steel construction with sliding door access and tinted safety glass windows opening at side. Door window is powered control. Windshield glass and roof window glass window are shatter-resistant. Tilt-telescoping steering wheel. Adjustable control lever stands for swing, boom hoist, boom telescoping, auxiliary hoist and main hoist. Control lever stands can change neutral positions and tilt for easy access into cab. 3 way adjustable operator's seat with high back, headrest and armrest. Engine throttle knob. Foot operated controls: boom hoist, boom telescoping, service brake and engine throttle. Hot water cab heater and air conditioning (OPTONAL). Dash-mounted engine start/stop, monitor lamps, cigarette lighter ashtray, drive selector switch, parking brake switch, steering mode select switch, power window switch, pump engaged/ disengaged switch, swing brake switch, telescoping/auxiliary winch select switch, outrigger controls, main winch/auxiliary winch selector switch, swing stop cancel switch, slow elevation stop cancel switch and free swing / lock swing selector switch. nstruments - Torque converter oil temperature, engine water temperature, air pressure, fuel, speedometer, tachometer and hour meter. Hydraulic oil pressure is monitored and displayed on the AML-L display panel. 2

3 Tadano electronic LOAD MOMENT NDCATOR system (AML-L) including: Control lever lockout function with audible and visual pre-warning. Boom position indicator Outrigger state indicator Boom angle / boom length / jib offset angle / load radius / rated lifting capacities / actual loads read out Ratio of actual load moment to rated load moment indication Automatic Speed Reduction and Soft Stop function on boom elevation and swing (swing range restricted only) Working condition register switch Load radius / boom angle / tip height / swing range preset function External warning lamp CARRER SPECFCATONS TADANO AML-L monitors outrigger extended length and automatically programs the corresponding "RATED LFTNG CAPACTES" table. Operator's right hand console includes transmission gear selector and sight level bubble. Upper console includes working light switch, roof washer and wiper switch, oil cooler switch, emergency outrigger set up key switch, drum indicator switch, jib equipped/removed select switch, boom emergency telescoping switch (2nd and 3rd-top) and air conditioning control switch. Swing lock lever. NOTE:Each crane motion speed is based on unladen conditions. TYPE - Rear engine, left hand steering, driving axle 2-way selected type by manual switch, 4x2 front drive, 4x4 front and rear drive. FRAME - High tensile steel, all welded mono-box construction. SUSPENSON - Front: Rigid mounted to frame. Rear: Pivot mounted with hydraulic lockout device. BRAKE SYSTEMS - Service: Air over hydraulic disc brakes on all 4 wheels. Parking/Emergency: Spring applied-air released brake acting on input shaft of front axle. Auxiliary: Electropneumatic operated exhaust brake. TRANSMSSON - Electronically controlled full automatic transmission. Torque converter driving full powershift with driving axle selector. 6 forward and 2 reverse speeds, constant TRES PR(OR) mesh. 3 speeds - high range - 2 wheel drive; 4 wheel drive OUTRGGERS - Four hydraulic, beam and jack outriggers. 3 speeds - low range - 4 wheel drive Vertical jack cylinders equipped with integral holding valve. Each outrigger beam and jack is controlled independently from cab. TRAVEL SPEED - 25 mph (4 km/h) Beams extend to 23' 7-1/2" (7.2 m) center-line and retract to within 1' 1-1/2" (3.315 m) overall width with floats. Outrigger AXLE - Front: Full floating type, steering and driving axle with jack floats are attached thus eliminating the need of manually planetary reduction. Rear: Full floating type, steering and driving attaching and detaching them. Controls and sight bubble located axle with planetary reduction and non-spin rear differential. in superstructure cab. Four outrigger extension lengths are provided with corresponding "RATED LFTNG CAPACTES" for STEERNG- Hydraulic power steering controlled by steering crane duty in confined areas. wheel. Four steering modes available: 2 wheel front, 2 wheel Min. Extension 9' 2-1/4" center to center rear, 4 wheel coordinated and 4 wheel crab. Mid. Extension 18' 1/2" center to center Mid. Extension 21' 11-3/4" center to center Max. Extension 23' 7-1/2" center to center Float size(diameter) 1' 7-11/16" (.5m) ENGNE Model Mitsubishi 6D16-TLEE Radiator Fin and tube core, thermostat controlled Type Direct injection diesel Fan, in.(mm) Suction type, 6-blade, 23.6 (6) dia. No. of cylinders 6 Starting 24 volt Combustion 4 cycle, turbo charged and after cooled Charging 24 volt system, negative ground BoreXStroke, in.(mm) X (118X115) Battery 2-12 amp. Hour Displacement, cu. in (liters) 46 (7.545) Compressor, air, CFM(l /min) 9.2 CFM (26) at 2,8rpm Air inlet heater 24 volt preheat Horsepower (kw) Gross 223 (1) at 2,7rpm Air cleaner Dry type, replaceable element Torque, Max. ft-lb (kgm) 521 (72) at 1,3rpm Oil filter Full flow with replaceable element Capacity, gal.(liters) Fuel filter Full flow with replaceable element Cooling water 3.4 (13) Fuel tank, gal.(liters) 79.2 (3), right side of carrier Lubrication 3.7 ~ 4.2 (14 ~ 16) Cooling Liquid pressurized, recirculating by-pass Fuel 79.2 (3) 3

4 STANDARD EQUPMENT - Four section full power partially synchronized boom - ndependently controlled outriggers 37.7'~144.4' (11.5 m~44. m) - Four outrigger extension positions '~58.1' (9.9 m~17.7 m) bi-fold lattice jib (tilt type) - Self-storing outrigger pads with 3.5 o, 25 o or 45 o pinned offsets and self storing pins. - Outrigger hose protection - Auxiliary lifting sheave (single top) stowable - Mitsubishi 6D16-TLEE turbo charged after cooled engine - Variable speed main hoist with grooved drum, cable follower (223HP) with exhaust brake and 797' of 3/4" cable. - Electronic controlled automatic transmission driven by torque - Variable speed auxiliary hoist with grooved drum, cable converter follower and 436' of 3/4" cable. - 4 X 4 X 4 drive/steer - Drum rotation indicator (thumper type) main and auxiliary hoist - Non-spin rear differential - Anti-Two block device (overwind cutout) - Automatic rear axle oscillation lockout system - Boom angle indicator PR (OR) tires - Tadano electronic load moment indicator system (AML-L) - Disc brakes - Outrigger extension length detector - Fenders - Electronic crane monitoring system - Air dryer - Tadano twin swing system and 36 o positive swing lock - Water separator with filter - Self centering finger control levers with pilot control - Engine over-run alarm - Control pedals for boom hoist and boom telescoping - Back-up alarm - 3 way adjustable cloth seat with armrests, high back - Low oil pressure/high water temp. warning device (visual) and seat belt - Rear steer centering light - Tilt-telescoping steering wheel - Air cleaner dust indicator - Tinted safety glass and sun visor - Full instrumentation package - Front windshield wiper and washer - Complete highway light package - Roof window wiper and washer - Flood lights and work lights - Power window (cab door) - Tool storage compartment - Rear view mirrors (right and left side) - Tire inflation kit - Mirror for main and auxiliary hoists - 24 volt electric system - Cigarette lighter and ashtray ton (5.6 metric ton) hook with swivel - Electric fan in cab - Towing hooks-front and rear - Cab floor mat - Lifting eyes - Pump disconnect in operator's cab - Hydraulic oil cooler - Hook block tie down (front bumper) - Weighted hook storage compartment OPTONAL EQUPMENT - 8 ton (72.6 metric ton) - 7 sheave with swivel hook and safety latch for 3/4"(19 mm) wire rope - 5 ton (45.4 metric ton) - 4 sheave with swivel hook and safety latch for 3/4"(19 mm) wire rope - Hot water cab heater and air conditioner - Propane heater (less tank) HOSTNG PERFORMANCE LNE SPEEDS AND PULLS DRUM WRE ROPE CAPACTES Layer Speed Main or auxiliary hoist - 15'-3/4" (.4m) drum Wire Main and auxiliary drum grooved lagging Line speeds 2 Line pulls 3/4" (19mm) wire rope rope Available 1 Permissible 4 Rope per layer Total wire rope layer F.P.M m/min Lbs. kgf Lbs. kgf Feet Meters Feet Meters 1st High ,2 8,26 15,2 6, nd High ,7 7,57 13,9 6, rd High ,4 6,99 12,8 5, th High ,3 6,49 11,9 5, th High ,4 6,6 11,1 5, th High ,5 5,68 1,4 4, th 3 High ,8 5,35 9,8 4, , Developed by machinery with each layer of wire rope, but not based DRUM DMENSONS on rope strength or other limitation in machinery or equipment. nch mm Line speeds based only on hook block, not loaded. Root diameter 15-3/4" 4 Seventh layer of wire rope are not recommendedfor hoisting Length 22-3/4" 578 operations. Flange diameter 27-3/8" 695 Permissible line pull may be affected by wire rope strength. 4

5 TR-8XXL WORKNG RANGE CHART Mode Mode 3.5 o 25 o 45 o 22' 3.5 o 25 o 45 o 22' 21' 21' 2' 2' 19' 19' 18' 18' 8 o 7 o 144.4' Boom 117.7' Boom 144.4' Boom ' Jib 144.4' Boom ' Jib 6 o 55 o 5 o 45 o 4 o 17' 16' 15' 14' 13' 12' 11' 1' Lifting Height in feet 8 o 7 o 144.4' Boom 131' Boom 117.7' Boom 144.4' Boom ' Jib 144.4' Boom ' Jib 6 o 55 o 5 o 45 o 4 o 17' 16' 15' 14' 13' 12' 11' 1' Lifting Height in feet 9' 9' 37.7' Boom 64.4' Boom 51' Boom 91' Boom 3 o 2 o 8' 7' 6' 5' 4' 37.7' Boom 64.4' Boom 91' Boom 3 o 2 o 8' 7' 6' 5' 4' 1 o 3' 1 o 3' 2' 2' o 1' o 1' Axis of Rotation 1' 2' 3' 4' 5' 6' 7' 8' 9' 1' 11' 12' 13' 14' Load Radius from Axis of Rotation in Feet Boom Length in Feet ( Mode ) 15' Axis of Rotation 1' 2' 3' 4' 5' 6' 7' 8' 9' 1' 11' 12' 13' 14' Load Radius from Axis of Rotation in Feet Boom Length in Feet ( Mode ) 15' NOTE : 1.Boom and jib geometry shown are for unloaded condition and machine standing level on firm supporting surface. Boom deflection and subsequent radius and boom angle change must be accounted for when applying load to hook. 5

6 TR-8XXL RATED LFTNG CAPACTES (N POUNDS) ON OUTRGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD 36 o ROTATON A 37.7' 51' 64.4' (19.62m) 91' (27.75m) 117.7' (35.87m) 131' 144.4' B C (11.5m) C (15.56m) C C C C C C C (39.93m) C (44.m) , 75 13, , , , 72 13, , , , 69 13, , , 79 44, 79 3, , , , , 76 44, 76 3,8 79 3, , , , 64 56, , 73 44, 73 3,8 77 3, , ,6 8 17, , , , , 7 39, 7 26,7 75 3, , , , ,8 53, 53 39,9 34, 23, , , , , , , , ,7 63 2,4 7 24,7 7 17, , , ,9 4 2, 4 26, , , , , , , , , , , , , , , , , , , ,3 13, , 37 11,4 53 1,7 53 9, ,1 62 1, ,1 24 9,5 46 7,6 46 8,4 53 9, 57 8, ,3 38 7,2 46 6,9 51 6, ,5 28 5,9 39 5,1 45 4, ,1 12 4,6 31 3,6 39 2, ,6 32 1,8 D o 18 o 32 o conditions (%) mode 2nd boom 3rd boom 4th boom Top boom, , LFTNG CAPACTES AT ZERO DEGREE BOOM ANGLE ON OUTRGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD 36 o ROTATON A 37.7' 51' 64.4' 64.4' 91' 91' 117.7' 117.7' C B (11.5m) B (15.56m) B (19.62m) B (19.62m) B (27.75m) B (27.75m) B (35.87m) B (35.87m) o , , , , , , , ,3 mode, A :Boom length in feet B :Load radius in feet C :Loaded boom angle (deg.) D :Minimum boom angle (deg.) for indicated length (no load) NOTE: -The lifting capacity data stored in the LOAD MOMENT NDCATOR (AML-L) is based on the standard number of parts of line listed in the chart. -Standard number of parts of line for outrigger operation should be according to the following table. Boom Length in Feet (meters) 37.7' 37.7' to 51' 51' to 64.4' 64.4' to 91' 91' to 144.4' Single top (11.5m) (11.5m to 15.56m) (15.56m to 19.62m) (19.62m to 27.75m) (27.75m to 44.m) Jib Number of parts of line

7 TR-8XXL RATED LFTNG CAPACTES (N POUNDS) ON OUTRGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD 36 o ROTATON 144.4' (44.m) Boom ' (9.9m) Jib 144.4' (44.m) Boom ' (17.7m) Jib C 3.5 o Tilt 25 o Tilt 45 o Tilt C 3.5 o Tilt 25 o Tilt 45 o Tilt 8 o , , ,1 8 o 4.6 5, , ,4 75 o 5.3 9, , ,3 75 o 6.6 5, , ,4 7 o.4 9, , ,6 7 o , , ,4 65 o 8.5 7, , , 65 o , , ,1 6 o , , ,4 6 o , , ,9 55 o 16. 5, , ,3 55 o , , ,7 5 o , , , 5 o , , ,7 45 o ,2 1. 2, , 45 o ,2 4 o , ,2 ON OUTRGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD 36 o ROTATON 117.7' (35.87m) Boom (telescoping mode ) 117.7' (35.87m) Boom (telescoping mode ) C ' (9.9m) Jib ' (17.7m) Jib 3.5 o Tilt 25 o Tilt 45 o C Tilt 3.5 o Tilt 25 o Tilt 45 o Tilt 8 o , , ,4 8 o.6 7, , ,7 75 o , , 57. 8, 75 o 5.4 7, , ,7 7 o , , ,4 7 o , , ,6 65 o , , ,7 65 o 8.2 6, , ,5 6 o , , ,2 6 o , , ,3 55 o , , , 55 o 16. 4, , ,1 5 o , , ,4 5 o , , , 45 o 16. 4, , ,2 45 o , , ,6 4 o , , 4 o , ,8 35 o , ,3 35 o , ,2 3 o , ,7 25 o , ,2 ON OUTRGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD 36 o ROTATON 117.7' (35.87m) Boom (telescoping mode ) 117.7' (35.87m) Boom (telescoping mode ) C ' (9.9m) Jib ' (17.7m) Jib 3.5 o Tilt 25 o Tilt 45 o Tilt C 3.5 o Tilt 25 o Tilt 45 o Tilt 8 o , , ,3 8 o , , ,7 75 o , , ,7 75 o 51. 6, , ,7 7 o , , 7.1 6,9 7 o 67. 6, , ,6 65 o.3 8, , 8.4 6,2 65 o 8.9 5, , ,3 6 o , , ,7 6 o , , , 55 o , , ,2 55 o 16. 3, , ,8 5 o , 15. 4, ,5 5 o , , ,7 45 o 17. 4, , , 45 o , , ,5 4 o , ,6 4 o , ,3 35 o , ,3 35 o , , 3 o , , 3 o , ,8 25 o , ,8 25 o , ,7 2 o ,65 2 o ,55 15 o ,5 15 o ,45 C :Loaded boom angle (deg.) R :Load radius in feet W :Rated lifting capacity in pounds 7

8 TR-8XXL RATED LFTNG CAPACTES (N POUNDS) ON OUTRGGERS MD EXTENDED 21' 11-3/4'' (6.7m) SPREAD 36 o ROTATON A 37.7' 51' 64.4' (19.62m) 91' (27.75m) 117.7' (35.87m) 131' 144.4' B C (11.5m) C (15.56m) C C C C C C C (39.93m) C (44.m) , 75 13, , , , 72 13, , , , 69 13, , , 79 44, 79 3, , , , , 76 44, 76 3,8 79 3, , , , , , 73 44, 73 3,8 77 3, , ,6 8 17, , , , , 7 39, 7 26,7 75 3, , , , , 53 28, ,2 32, 23, , , , , , , , ,9 63 2,4 7 24,7 7 17, , , , 4 16,5 4 22, , , , , , , , , 55 15, , , , , , , , , , ,3 12, ,8 37 9,9 52 8, 53 9,9 58 9,6 61 8, ,2 24 7,1 45 5,2 46 7,8 52 6,8 56 6, ,2 38 5,7 46 4,7 51 4, ,6 28 4,1 39 3,1 45 2, ,8 3 1,9 39 1,2 D o 27 o o 3 o 39 o conditions (%) mode 2nd boom 3rd boom 4th boom Top boom, , LFTNG CAPACTES AT ZERO DEGREE BOOM ANGLE ON OUTRGGERS MD EXTENDED 21' 11-3/4'' (6.7m) SPREAD 36 o ROTATON A 37.7' 51' 64.4' 64.4' 91' 91' 117.7' C B (11.5m) B (15.56m) B (19.62m) B (19.62m) B (27.75m) B (27.75m) B (35.87m) o , , , , , , ,5 mode, A :Boom length in feet B :Load radius in feet C :Loaded boom angle (deg.) D :Minimum boom angle (deg.) for indicated length (no load) NOTE: -The lifting capacity data stored in the LOAD MOMENT NDCATOR (AML-L) is based on the standard number of parts of line listed in the chart. -Standard number of parts of line for outrigger operation should be according to the following table. Boom Length in Feet (meters) 37.7' 37.7' to 51' 51' to 64.4' 64.4' to 91' 91' to 144.4' Single top (11.5m) (11.5m to 15.56m) (15.56m to 19.62m) (19.62m to 27.75m) (27.75m to 44.m) Jib Number of parts of line

9 TR-8XXL RATED LFTNG CAPACTES (N POUNDS) ON OUTRGGERS MD EXTENDED 21' 11-3/4'' (6.7m) SPREAD 36 o ROTATON 144.4' (44.m) Boom ' (9.9m) Jib 144.4' (44.m) Boom ' (17.7m) Jib C 3.5 o Tilt 25 o Tilt 45 o Tilt C 3.5 o Tilt 25 o Tilt 45 o Tilt 8 o , , ,1 8 o 4.6 5, , ,4 75 o 5.3 9, , ,3 75 o 6.6 5, , ,4 7 o.4 9, , ,6 7 o , , ,4 65 o 8. 7, , , 65 o , , ,1 6 o , , ,1 6 o 11. 3, , ,5 55 o 14. 2, , ,6 55 o , , ,4 5 o , , ,5 ON OUTRGGERS MD EXTENDED 21' 11-3/4'' (6.7m) SPREAD 36 o ROTATON 117.7' (35.87m) Boom (telescoping mode ) 117.7' (35.87m) Boom (telescoping mode ) C 3.5 o Tilt ' (9.9m) Jib ' (17.7m) Jib C 25 o Tilt 45 o Tilt 3.5 o Tilt 25 o Tilt 45 o Tilt 8 o , , ,4 8 o.6 7, , ,7 75 o , , 57. 8, 75 o 5.4 7, , ,7 7 o , , ,4 7 o , , ,6 65 o , , ,7 65 o 8.2 6, , ,5 6 o , , ,2 6 o , , ,3 55 o , , ,7 55 o 15. 3, , , 5 o , , ,4 5 o , , , 45 o 16. 2, , ,3 45 o , , ,2 4 o , ,4 ON OUTRGGERS MD EXTENDED 21' 11-3/4'' (6.7m) SPREAD 36 o ROTATON 117.7' (35.87m) Boom (telescoping mode ) 117.7' (35.87m) Boom (telescoping mode ) C 3.5 o Tilt ' (9.9m) Jib ' (17.7m) Jib C 25 o Tilt 45 o Tilt 3.5 o Tilt 25 o Tilt 45 o Tilt 8 o , , ,3 8 o , , ,7 75 o , , ,7 75 o 51. 6, , ,7 7 o , , 7.1 6,9 7 o 67. 6, , ,6 65 o.3 8, , 8.4 6,2 65 o 8.9 5, , ,3 6 o , , ,7 6 o , , , 55 o , , ,2 55 o 16. 3, , ,8 5 o , 15. 4, ,5 5 o , , ,7 45 o 17. 4, , , 45 o , , ,5 4 o , ,3 4 o , , 35 o , ,6 35 o , ,4 3 o , ,1 3 o ,1 25 o , ,7 2 o ,4 15 o ,2 C :Loaded boom angle (deg.) R :Load radius in feet W :Rated lifting capacity in pounds 9

10 TR-8XXL RATED LFTNG CAPACTES (N POUNDS) ON OUTRGGERS MD EXTENDED 18' 1/2'' (5.5m) SPREAD 36 o ROTATON A 37.7' 51' 64.4' (19.62m) 91' (27.75m) 117.7' (35.87m) 131' 144.4' B C (11.5m) C (15.56m) C C C C C C C (39.93m) C (44.m) , 75 13, , , , 72 13, , , , 69 13, , , 79 44, 79 3, , , , , 76 44, 76 3,8 79 3, , , ,4 64 4, , 73 43,5 73 3,8 77 3, , ,6 8 17, ,1 48 3, , ,2 7 31,6 7 26,7 75 3, , , , ,1 53 2, ,1 23,7 23, , , , , , , 47 2, ,2 63 2,4 7 2,3 7 17, , , ,6 4 11, 4 16, , , 67 16, , , , , 32 13, , , , , ,7 7 13, ,6 46 1, 58 8,1 59 1,9 63 9,9 8, ,5 36 6,8 52 4,9 52 7,6 57 6,7 61 5, ,4 23 4,6 45 2,7 45 5,3 52 4,3 56 3, ,5 45 2,6 5 1, ,2 38 1, ,1 D o 41 o 12 o 38 o 5 o conditions (%) mode 2nd boom 3rd boom 4th boom Top boom, , LFTNG CAPACTES AT ZERO DEGREE BOOM ANGLE ON OUTRGGERS MD EXTENDED 18' 1/2'' (5.5m) SPREAD 36 o ROTATON A 37.7' 51' 64.4' 64.4' 91' 91' C B (11.5m) B (15.56m) B (19.62m) B (19.62m) B (27.75m) B (27.75m) o , , , , , ,7 mode, A :Boom length in feet B :Load radius in feet C :Loaded boom angle (deg.) D :Minimum boom angle (deg.) for indicated length (no load) NOTE: -The lifting capacity data stored in the LOAD MOMENT NDCATOR (AML-L) is based on the standard number of parts of line listed in the chart. -Standard number of parts of line for outrigger operation should be according to the following table. Boom Length in Feet (meters) 37.7' 37.7' to 51' 51' to 64.4' 64.4' to 91' 91' to 144.4' Single top (11.5m) (11.5m to 15.56m) (15.56m to 19.62m) (19.62m to 27.75m) (27.75m to 44.m) Jib Number of parts of line

11 TR-8XXL RATED LFTNG CAPACTES (N POUNDS) ON OUTRGGERS MD EXTENDED 18' 1/2'' (5.5m) SPREAD 36 o ROTATON 144.4' (44.m) Boom ' (9.9m) Jib 144.4' (44.m) Boom ' (17.7m) Jib C 3.5 o Tilt 25 o Tilt 45 o Tilt C 3.5 o Tilt 25 o Tilt 45 o Tilt 8 o , , ,1 8 o 4.6 5, , ,4 75 o 5.3 9, , ,3 75 o 6.6 5, , ,4 7 o , 75. 6, ,3 7 o , , ,4 65 o , , , 65 o , , ,4 6 o 9.9 2, , ,3 6 o 17. 1, , ,1 55 o 12. 1, , ,1 ON OUTRGGERS MD EXTENDED 18' 1/2'' (5.5m) SPREAD 36 o ROTATON 117.7' (35.87m) Boom (telescoping mode ) 117.7' (35.87m) Boom (telescoping mode ) C 3.5 o Tilt ' (9.9m) Jib ' (17.7m) Jib 25 o Tilt 45 o C Tilt 3.5 o Tilt 25 o Tilt 45 o Tilt 8 o , , ,4 8 o.6 7, , ,7 75 o , , 57. 8, 75 o 5.4 7, , ,7 7 o , , ,4 7 o , , ,6 65 o 65. 8, , ,2 65 o , , ,5 6 o , , ,2 6 o 92. 3, , ,6 55 o , , ,7 55 o 14. 1, , ,5 5 o , , ,6 ON OUTRGGERS MD EXTENDED 18' 1/2'' (5.5m) SPREAD 36 o ROTATON 117.7' (35.87m) Boom (telescoping mode ) 117.7' (35.87m) Boom (telescoping mode ) C 3.5 o Tilt ' (9.9m) Jib ' (17.7m) Jib 25 o Tilt 45 o Tilt C 3.5 o Tilt 25 o Tilt 45 o Tilt 8 o , , ,3 8 o , , ,7 75 o , , ,7 75 o 51. 6, , ,7 7 o , , 7.1 6,9 7 o 67. 6, , ,6 65 o.3 8, , 8.4 6,2 65 o 8.9 5, , ,3 6 o , , ,7 6 o , , , 55 o , 96. 4, ,3 55 o 16. 3, , ,7 5 o , , ,2 5 o , , ,8 45 o 16. 2, , ,3 45 o , , ,2 4 o , ,7 35 o , ,1 C :Loaded boom angle (deg.) R :Load radius in feet W :Rated lifting capacity in pounds 11

12 TR-8XXL RATED LFTNG CAPACTES (N POUNDS) ON OUTRGGERS MN EXTENDED 9' 2-1/4'' (2.8m) SPREAD 36 o ROTATON A 37.7' 51' 64.4' (19.62m) 91' (27.75m) 117.7' (35.87m) 131' 144.4' B C (11.5m) C (15.56m) C C C C C C C (39.93m) C (44.m) , , , 78 44, , 72 58, , , ,4 68 4, 73 39, 73 43, ,7 79 3, , , , , ,6 76 3, , , , , , , , , , , ,6 8 17, , 48 9,9 59 9, , , , , , , , ,2 53 5,5 53 1,4 65 8,6 11,9 72 9, , , , ,4 47 2,8 47 7,4 62 5,6 62 8,9 69 6,9 69 9,6 72 8,7 74 7, ,3 4 5,2 58 3,4 58 6,7 4,7 7,3 69 6,4 71 5, ,4 54 1,7 54 4,9 63 2,9 64 5,6 67 4,7 69 3, ,3 58 3, 62 2,1 65 1, ,2 D o 44 o o 54 o 43 o 61 o 51 o 61 o 65 o conditions (%) mode 2nd boom 3rd boom 4th boom Top boom, , LFTNG CAPACTES AT ZERO DEGREE BOOM ANGLE ON OUTRGGERS MN EXTENDED 9' 2-1/4'' (2.8m) SPREAD 36 o ROTATON A 37.7' 51' 64.4' C B (11.5m) B (15.56m) B (19.62m) o , , ,7 mode, A :Boom length in feet B :Load radius in feet C :Loaded boom angle (deg.) D :Minimum boom angle (deg.) for indicated length (no load) NOTE: -The lifting capacity data stored in the LOAD MOMENT NDCATOR (AML-L) is based on the standard number of parts of line listed in the chart. -Standard number of parts of line for outrigger operation should be according to the following table. Boom Length in Feet (meters) 37.7' 37.7' to 51' 51' to 64.4' 64.4' to 91' 91' to 144.4' Single top (11.5m) (11.5m to 15.56m) (15.56m to 19.62m) (19.62m to 27.75m) (27.75m to 44.m) Jib Number of parts of line

13 WARNNG AND OPERATNG NSTRUCTONS FOR LFTNG CAPACTES GENERAL 1. When making lifts at a load radius not shown, use the next 1. RATED LFTNG CAPACTES apply only to the machine as longer radius to determine allowable capacity. originally manufactured and normally equipped by TADANO 11. Load per line should not exceed 12,3 lbs. (5,6kg) for LTD. Modifications to the machine or use of optional main winch and auxiliary winch. equipment other than that specified can result in a reduction 12. Check the actual number of parts of line with LOAD MOMENT of capacity. NDCATOR (AML-L) before operation. Maximum lifting 2. Construction equipment can be hazardous if improperly capacity is restricted by the number of parts of line of LOAD operated or maintained. Operation and maintenance of this MOMENT NDCATOR (AML-L). Limited capacity is as machine must be in compliance with information in the determined from the formula, Single line pull for main winch operation, safety and maintenance manual supplied with (12,3 lbs.) x number of parts of line. machine. f these manuals are missing, order replacements 13. The boom angle before loading should be greater to account through the distributor. for deflection. For rated lifting capacities, the loaded boom 3. The operator and other personnel associated with this angle and the load radius is for reference only. machine shall fully acquaint themselves with the latest 14. The 37.7' (11.5m) boom length capacities are based on boom American National Standards nstitute (ANS) safety fully retracted. f not fully retracted [less than 51'(15.56m) standards for cranes. boom length, use the rated lifting capacities for the 51' (15.56m) boom length. SET UP 15. Extension or retraction of the boom with loads may be 1. Rated lifting capacities on the chart are the maximum attempted within the limits of the RATED LFTNG CAPACTES. allowable crane capacities and are based on the machine The ability to telescope loads is limited by hydraulic pressure, standing level on firm supporting surface under ideal job boom angle, boom length, crane maintenance, etc. conditions. Depending on the nature of the supporting 16. For lifting capacity of single top, reduce the rated lifting surface, it may be necessary to have structural supports capacities of relevant boom according to a weight reductions under the outrigger floats or tires to spread the loads to a for auxiliary load handling equipment. Capacities of single top larger bearing surface. shall not exceed 12,3 lbs. (5,6kg) including main hook. 2. For outrigger operation, outriggers shall be properly extended 17. When base jib or top jib or both jib removing, jib state switch with tires free of supporting surface before operating crane. select removed. 18. When erecting and stowing jib, be sure to retain it by hand or by OPERATON other means to prevent its free movement. 1. Rated lifting capacities have been tested to and meet 19. Use "ANT-TWO BLOCK" disable switch when erecting and minimum requirements of SAE J163-Cantilevered Boom stowing jib and when stowing hook block. While the switch is Crane Structures Method of Test. pushed, the hoist does not stop, even when overwind condition 2. Rated lifting capacities do not exceed 85 % of the tipping occurs. load on outriggers fully extended as determined by SAE 2. For boom length with 32.5' (9.9m) jib, rated lifting capacities are J765-Crane Stability Test Code. determined by loaded boom angle only in the column headed Rated lifting capacities for partially extended outriggers are "144.4' (44.m) boom ' (9.9m) jib". determined from the formula, Rated Lifting Capacities For boom length with 58.1' (17.7 m) jib, rated lifting capacities =(Tipping Load -.1 x Tip Reaction)/1.25. are determined by loaded boom angle only in the column 3. Rated lifting capacities above bold lines in the chart are headed "144.4' (44.m) boom ' (17.7m) jib". based on crane strength and those below, on its stability. For angles not shown, use the next lower loaded boom angle They are based on actual load radius increased by boom to determine allowable capacity. deflection. 21. When lifting a load by using jib (aux. winch) and boom (main 4. The weight of handling device such as hook blocks, slings, winch) simultaneously, do the following: etc., must be considered as part of the load and must be Enter the operation status as jib operation, not as boom deducted from the lifting capacities. operation. 5. Rated lifting capacities are based on freely suspended loads Before starting operation, make sure that mass of load is and make no allowance for such factors as the effect of wind, within rated lifting capacity for jib. sudden stopping of loads, supporting surface conditions, inflation of tires, operating speeds, side loads, etc. Side pull DEFNTONS on boom or jib is extremely dangerous. 1. Load Radius: Horizontal distance from a projection of the axis 6. Rated lifting capacities do not account for wind on lifted load of rotation to supporting surface before loading to the center of or boom. Rated lifting capacities and boom length shall be the vertical hoist line or tackle with load applied. appropriately reduced, when wind velocity is above 2 mph 2. Loaded Boom Angle: The angle between the boom base (9 m/sec.). section and the horizontal, after lifting the rated lifting capacity 7. Rated lifting capacities at load radius shall not be exceeded. at the load radius. Do not tip the crane to determine allowable loads. 3. Working Area: Area measured in a circular arc about the 8. Do not operate at boom lengths, radii, or boom angle, where centerline of rotation. no capacities are shown. Crane may overturn without any 4. Freely Suspended Load: Load hanging free with no direct load on the hook. external force applied except by the hoist line. 9. When boom length is between values listed, refer to the 5. Side Load: Horizontal side force applied to the lifted load either rated lifting capacities of the next longer and next shorter on the ground or in the air. booms for the same radius. The lesser of the two rated lifting capacities shall be used. 13

14 TR-8XXL RATED LFTNG CAPACTES (N POUNDS) ON RUBBER TRE : PR Stationary Creep A OVER FRONT 36 o ROTATON OVER FRONT 37.7' 64.4' 91' 37.7' 64.4' 91' 37.7' 64.4' 91' B C (11.5m) C (19.62m) C (27.75m) C (11.5m) C (19.62m) C (27.75m) C (11.5m) C (19.62m) C (27.75m) , , , , , , , , , , ,3 5 18, 69 21,3 5 29, 69 31, , 64 29, , , , , , , ,1 21 7,6 58 1,6 69 1, ,2 59 2, , ,1 19,1 53 7,5 65 7, ,5 17, , ,3 47 5,3 62 5, , , , ,4 4 3,6 58 4,2 4 11, , , 55 1, 32 2,3 54 3, 32 9, 55 1, ,1 5 8,2 21 1,2 5 2,1 21 7,1 5 8, ,6 45 1,3 46 6, ,4 41 5, ,3 36 4, ,4 29 3, ,7 22 2,7 D o o 21 o 45 o o conditions (%) mode 2nd boom 3rd boom 4th boom Top boom,,, LFTNG CAPACTES AT ZERO DEGREE BOOM ANGLE ON RUBBER OPERATON Stationary Creep A OVER FRONT 36 o ROTATON OVER FRONT 37.7' 64.4' 91' 37.7' 37.7' 64.4' 91' C B (11.5m) B (19.62m) B (27.75m) B (11.5m) B (11.5m) B (19.62m) B (27.75m) o , , 85. 1, , , , 85. 1,9 A :Boom length in feet B :Load radius in feet C :Loaded boom angle (deg.) D :Minimum boom angle (deg.) for indicated length (no load) NOTE: -The lifting capacity data stored in the LOAD MOMENT NDCATOR (AML-L) is based on the standard number of parts of line listed in the chart. -Standard number of parts of line for rubber operation should be according to the following table. Boom Length in Feet 37.7' 37.7' to 91' (meters) (11.5m) (11.5m to 27.75m) Number of parts of line 6 4 Single top Jib 1 WARNNG AND OPERATNG NSTRUCTONS FOR ON RUBBER LFTNG CAPACTES 1.Rated lifting capacities on rubber are in pounds and do not exceed 6. Over front operation shall be performed within two degrees in front of 75 % of tipping loads as determined by SAE J765-Crane Stability chassis. Test Code. 7. On rubber lifting with "jib" is not permitted. Maximum permissible 2.Rated lifting capacities shown in the chart are based on condition boom length is 91 ft. (27.75m). that crane is set on firm level surfaces with axle oscillation lockout 8. When making lift on rubber stationary, set parking brake. applied. Those above bold lines are based on tire capacity and 9. For creep operation, boom must be centered over front of machine, those below, on crane stability. They are based on actual load swing lock engaged, and load restrained from swinging. Travel slowly radius increased by tire deformation and boom deflection. and keep the lifted load as close to the ground as possible, and 3.f the axle oscillation lockout cylinders contain air, the axle will not especially avoid any abrupt steering, accelerating or braking. be locked completely and rated lifting capacities may not be 1. Do not operate the crane while carrying the load. obtainable. Bleed the cylinders according to the operation safety 11. Creep is motion for crane not to travel more than 2 ft. (6 m) in any and maintenance manual. 3 minute period and to travel at the speed of less than 1mph (1.6km/h). 4.Rated lifting capacities are based on proper tire inflation, capacity 12. For creep operation, set Drive select switch to "4-WHEEL (Lo)" and and condition. Damaged tires are hazardous to safe operation of set gear shift lever to "1". crane. 5.Tires shall be inflated to correct air pressure. Tires PR Air Pressure 6 psi (4.2 kgf/cm 2 ) 14

15 WARNNG AND OPERATNG NSTRUCTONS FOR USNG THE LOAD MOMENT NDCATOR (AML-L) 1. When operating crane on outriggers: When a load is lifted in the front position and then swung Set P.T.O. switch to "ON". to the side area, make sure the value of the LOAD Press the outrigger mode select key to register for the MOMENT NDCATOR(AML-L) is below the 36 o lifting outrigger operation. Press the set key, then the outrigger capacity. mode indicative symbol changes from flickering to lighting. (2) For creep operation. Press the boom mode select key to register the boom mode, The creep capacities are attainable only when boom is then the boom mode indicative symbol changes from in the straight forward position of chassis and the over lighting to flickering. Each time the boom mode select key is front position symbol is on. f boom is not in the straight pressed, the mode changes. Press the set key to select forward position of chassis, never lift load. the status that corresponds to the actual state of the boom, 3. A swing does not automatically stop even if the crane then the boom mode indicative symbol changes from flickering becomes overloaded. to lighting. 4. During crane operation, make sure that the displays on front When erecting and stowing jib, select the status of jib set panel are in accordance with actual operating conditions. (jib state indicative symbol flicker). 5. The displayed values of LOAD MOMENT NDCATOR 2. When operating crane on rubber: (AML-L) are based on freely suspended loads and make no Set P.T.O. switch to "ON". allowance for such factors as the effect of wind, sudden Press the outrigger mode select key. The on-tire mode stopping of loads, supporting surface conditions, inflation of indicative symbol comes on. Each time the outrigger mode tire, operating speed, side loads, etc. select key is pressed the mode changes. Select the creep For safe operation, it is recommended when extending and operation, the on-tire mode indicative symbol flicker. lowering boom or swinging, lifting loads shall be Press the boom mode select key to register the boom mode. appropriately reduced. However, pay attention to the following. 6. LOAD MOMENT NDCATOR (AML-L) is intended as an aid (1) For stationary operation. to the operator. Under no condition should it be relied upon The front capacities are attainable only when the over front to replace use of capacity charts and operating instruction. position symbol comes on. When the boom is more than Sole reliance upon LOAD MOMENT NDCATOR (AML-L) 2 degrees from centered over front of chassis, 36 o aids in place of good operating practice can cause an capacities are in effect. accident. The operator must exercise caution to assure safety. TR-8XXL- 4 Axle weight distribution chart Pounds Kilograms GVW Front Rear GVW Front Rear Base machine 15,934 54,437 51,498 48,51 24,692 23,359 Remove: ton (5.6 metric ton) hook ball Top jib (25.6') Base jib (32.5') -1,832-3,543 1, , Auxiliary lifting sheave Removable Counterweight -17,355 7,474-24,828-7,872 3,39-11,262 Options: 1. 8 ton (72.6 metric ton) hook block 1,817 3,276-1, , ton (45.4 metric ton) hook block 95 1, Hot water cab heater and air conditioner

16 MEMO TADANO AMERCA CORPORATON 3 NORTHPARK CENTRAL DRVE, SUTE Z, HOUSTON, TEXAS 7773 U.S.A. PHONE: (281) EXT.315 FAX: (281) Web site: sales@tadano-cranes.com Form No. GR /US-2 16