ATTACHMENTS CATALOGUE NO.6 CHALLENGEIMPLEMENTS. Australian technology to load, lift AND carry.
|
|
- Dana Opal Bridges
- 5 years ago
- Views:
Transcription
1 ATTACHMENTS CATALOGUE NO.6 CHALLENGEIMPLEMENTS Australian technology to load, lift AND carry
2 Contents Buckets pages 2-6 Post Hole Diggers page 7 Earthmoving Blades pages 8-9 Hay Handling Attachments page Hay Tines page 11 Silage Attachments pages Other Lifting Attachments pages Point Linkage Attachments pages Counterweights page 18
3 Over 50 Years of History Challenge Implements is a tractor loader and attachment specialist with its major manufacturing plant situated in Orange, New South Wales, approximately 260 kilometres west of Sydney. Orange is a regional city with a population of 39,000 and the area is promoted as the agribusiness capital of New South Wales. Main agricultural activities in the surrounding area include: cereal and oilseed production; wool and prime lambs; beef; dairies; apple, pear and stone fruit orchards; grapes and vineyards; vegetables; flowers and pine plantations. Challenge is a fully Australian-owned thirdgeneration family company. Challenge commenced manufacturing agricultural implements in Orange in 1957 with two employees and a capital of less than 500. The ultimate aim of the company was to develop a representative range of everyday agricultural equipment. Steps were taken even in the first year of operation to divert every available penny toward the necessary research and development required to produce such equipment. The year 1962 marked the release of the first Challenge front end loader along with a threepoint linkage grader. These products gained immediate market acceptance and established the brand name Challenge as implements of good design, robust in construction and offering value for money. Today Challenge continues to grow by expanding its operations throughout Australia. This allows Challenge to continue to support Australian farmers with fast, prompt and reliable service, with equipment designed by Australians for Australian conditions. From the very first loader made by Challenge in 1962, this Australian-owned company and its brand has created enviable traditions of worldclass engineering excellence and innovation.
4 General Purpose Buckets All general purpose buckets have been designed to meet the high strength and safety requirements of today s environment. There is a large variety of buckets available to cover a wide range of applications and to enable a more compatible loader/tractor combination, ensuring you get the most from your loader. All buckets are constructed from high tensile steel (570mpa) which is laser cut for accuracy and press formed to ensure superior strength. When attached to a Challenge front end loader, the bucket profile has been designed to ensure there is no rollback, a condition whereby material spills or falls over the rear of the bucket as it is filled. All earthmoving buckets enable maximum fill with minimum effort, ensuring an efficient loading cycle. The lower back portion of the bucket has a double plate arrangement that forms an enclosed 'box' section running the full width of the bucket, giving the bucket exceptional torsional strength. Buckets have a high quality roll formed cutting edge for excellent durability as well as wear plates on the bottom face of the bucket. Heavy section pipe gives a clean smooth face to the top of the bucket. The buckets' cut ends have been pressed to give strength along the edge and sides of the bucket. The attachment lugs on the rear of the bucket have plates that distribute the load to the strengthened sections of the bucket, directly behind the box section and to the formed edge towards the top of the bucket. This eliminates deformation in the back of the bucket during loading cycles. Most general purpose buckets can be fitted with ground-engaging teeth if required. Bucket Size Width: Measurement of the overall outside width of the bucket in millimetres. Depth (D¹): Horizontal distance in millimetres from tip of blade edge to rearmost vertical inner face of bucket. Overall Depth (D²): Horizontal distance in millimetres from the tip of the blade edge to the furthermost edge of the outer bucket. Height (H¹): Overall vertical height in millimetres from bottom of bucket to top edge of bucket. D¹ B U C K E T S p a g e 2 H¹ D²
5 General Purpose High Capacity BUCKET General Purpose Low Capacity BUCKET B u c k e t s p a g e 3 Compact LCC Mid LCM Low Capacity LC High Capacity HC Model 134LCC 150LCC 170LCC 186LCM 186LC 216LC 246LC 216HC 246HC Horse power range 21hp-45hp 21hp-45hp 21hp-45hp 45hp-70hp 55hp-360hp 55hp-360hp 55hp-360hp 55hp-360hp 55hp-360hp Width 1340mm 1500mm 1700mm 1860mm 1860mm 2160mm 2460mm 2160mm 2460mm 62kg 78kg 88kg 178kg 190kg 220kg 245kg 240kg 265kg Depth (D¹) 460mm 490mm 575mm 665mm 672mm 672mm 672mm 787mm 787mm Overall depth (D²) 695mm 740mm 805mm 940mm 964mm 964mm 964mm 1040mm 1040mm Height (H¹) 425mm 445mm 495mm 600mm 657mm 657mm 657mm 700mm 700mm Struck capacity 0.13m³ 0.17m³ 0.25m³ 0.38m³ 0.47m³ 0.55m³ 0.63m³ 0.66m³ 0.76m³ Rated capacity 0.16m³ 0.22m³ 0.31m³ 0.49m³ 0.57m³ 0.67m³ 0.77m³ 0.80m³ 0.90m³ Optional ground engaging teeth N/A N/A N/A N/A Grain Bucket The two grain buckets have the same rated capacity but offer different widths. They have been developed to handle larger volumes of lighter material. They have the same features as the general purpose bucket with the addition of internal ribs near the attachment lugs for extra strength in the back of the bucket. Grain Bucket GB Model 216GB 246GB Horse power range 55hp-360hp 55hp-360hp Width 2160mm 2460mm 320kg 336kg Depth (D¹) 1087mm 921mm Overall depth (D²) 1335mm 1230mm Height (H¹) 921mm 982mm Struck capacity 1.20m³ 1.20m³ Rated capacity 1.45m³ 1.45m³
6 Multi-Purpose Buckets (4-in-1) For the ultimate in versatility, the multipurpose 4-in-1 bucket gives you a bucket, a blade, a grab and a grader. This attachment requires a third hydraulic control circuit. Bucket With the multi-purpose bucket in the closed position you have a standard earthmoving bucket to pick up and move loose materials, with the option to open the bucket to empty material instead of dumping (ideal for unloading material over a high side-board of a truck or trailer). Blade With the multi-purpose bucket in the open position and the fixed half of the bucket in the vertical position you have an earthmoving blade. Grab As you approach the material to be handled you can open the multipurpose bucket and position it over or around the material then, closing the bucket jaws in a biting action, pick up the material. Grader With the multi-purpose bucket in the open position and dumped forward so the front internal cutting edge is in contact with the ground, you can drag the bucket backwards to scrape material into a heap or to backfill trenches. With the multi-purpose bucket in a similar orientation but with both internal cutting edges in contact with the ground, the bucket can be used as a leveller on firmer surfaces. All multi-purpose buckets have been designed to exceed the requirements of the agricultural industry and, when used with the standard level-lift Challenge front end loader, have safety features to eliminate rollback, this feature prevents material from falling over the rear of the bucket when it is filled. The multi-purpose buckets enable maximum fill with minimum effort, ensuring an efficient loading cycle. Buckets are available in a number of sizes to enable a more compatible loader/tractor combination, ensuring you get the most from your loader. The lower back portion of the bucket has a double plate arrangement constructed from high tensile steel (570mpa) that forms an enclosed 'box' section running the full width of the bucket, giving the bucket exceptional torsional strength. Buckets have high-quality roll-formed cutting edges for excellent durability. Heavy section pipe give a clean smooth face to the top of the bucket. The laser cut ends and hinges of the bucket have been cut from heavy highgrade plate to give maximum strength to the sides of the bucket. B U C K E T S p a g e 4 The bottom of the bucket has additional formed plate with internal rib section for maximum strength in the moving half of the bucket. Some multi-purpose buckets can be fitted with ground-engaging teeth if required.
7 MULTI-PURPOSE (4-IN-1) BUCKET Multi-Purpose Bucket with Ground Engaging Teeth fitted B u c k e t s p a g e 5 Compact MLCC Mid MLCM Low Capacity MLC High Capacity MHC Model 134MLCC 150MLCC 170MLCC 186MLCM 186MLC 216MLC 246MLC 216MHC Horse power range 21hp-60hp 21hp-60hp 21hp-60hp 55hp-70hp 55hp-360hp 55hp-360hp 55hp-360hp 55hp-360hp Width 1340mm 1500mm 1700mm 1860mm 1860mm 2160mm 2460mm 2160mm 113kg 144kg 165kg 235kg 326kg 362kg 391kg 441kg Depth (D¹) 393mm 380mm 494mm 545mm 560mm 560mm 560mm 750mm Overall depth (D²) 502mm 514mm 535mm 702mm 767mm 767mm 767mm 950mm Height (H¹) 394mm 440mm 491mm 553mm 613mm 613mm 613mm 755mm Overall height (H²) 520mm 514mm 560mm 625mm 776mm 776mm 776mm 845mm Maximum opening (O¹) 433mm 443mm 625mm 680mm 824mm 824mm 824mm 965mm Struck capacity 0.10m³ 0.12m³ 0.20m³ 0.25m³ 0.32m³ 0.37m³ 0.42m³ 0.56m³ Rated capacity 0.13m³ 0.15m³ 0.26m³ 0.32m³ 0.40m³ 0.46m³ 0.52m³ 0.70m³ Optional ground engaging teeth N/A N/A N/A N/A Bucket Size Width: Measurement of the overall outside width of the bucket in millimetres. Depth (D 1 ): Horizontal distance in millimetres from the tip of the cutting edge to rearmost inner face of the bucket when closed. Overall Depth (D 2 ): Horizontal distance in millimetres from the tip of the cutting edge to the furthermost edge of the outer bucket when closed. Height (H 1 ): Overall vertical height in millimetres from the top of the crossbar to the bottom of the bucket when closed. Overall Height (H 2 ): Overall vertical height in millimetres from the highest point of the bucket to the bottom of the bucket when closed. Maximum Opening (O 1 ): Maximum distance in millimetres between the inner cutting edges of the bucket when open. H² D² D¹ O¹ H¹
8 Rock Buckets The rock bucket is ideal for removing unwanted materials and sorting materials for reuse. It has a variety of uses including, digging and removing rocks from loose soil, cleaning up of materials such as branches, greenery and unwanted scrap. The rock bucket has been built for high strength, the heavy duty teeth are 20mm thick and the two outer teeth are 25mm thick increasing strength and wear life of the attachment. With easy to fit hitch lug plates, the rock bucket has the potential to be fitted to a variety of machines on the market or can be refitted to more than one machine. B U C K E T S p a g e 6 Rock Bucket STF2 Model 190STF2 220STF2 Width 1890mm 2230mm 359kg 418kg Depth 858mm 858mm Height 740mm 740mm Number of tines Struck capacity 0.30m m 3 Rated capacity 0.42m m 3 Note: Rated Capacity measured across side plates. Additional height gained by bend guard section of the bucket is not considered for calculation purposes.
9 Post Hole Diggers POST HOLE DIGGER Carriage & DRIVE UNIT Drive Unit Model 100PHD 200PHD 300PHD Flow rate range* 30L/min-57L/min 40L/min-65L/min 50L/min-95L/min The hydraulic post hole digger drive unit is operated by a third service from the front end loader to drive whichever size auger is fitted. The operator controls the loader arms to provide downward pressure while drilling the hole, or by raising the loader arms to lift the auger out of the hole. The post hole digger is supplied with a one piece attachment carriage. The drive unit can be positioned to the left, right or centre of the carriage to suit individual needs. There are a number of drive units to best match the tractor's hydraulic capacity and auger sizes to suit any job. All augers come standard with replaceable tungsten carbide cutting teeth and pilot. P o s t H o l e D i g g e r p a g e 7 Torque 220Bar 220Bar 240Bar 54kg 54kg 60kg * Flow rate range refers to the flow rate delivered to the attachment. To determine the appropriate drive unit model to suit your tractor, check the tractor hydraulic specifications from your tractor manufacturer. Note: Hydraulic oil flow at the attachment may not always be equal to the total oil flow indicated in the tractor specifications. Auger Model* 100ATC 150ATC 200ATC 250ATC 300ATC 350ATC 400ATC 450ATC 600ATC Diameter 100mm 150mm 200mm 250mm 300mm 350mm 400mm 450mm 600mm 16kg 18kg 20kg 26kg 29kg 32kg 36kg 38kg 44kg * Auger Tungsten Carbide ATC Note: 400mm, 450mm and 600mm augers are only available for 300PHD. Flow vs Speed PHD Torque vs Pressure PHD FLOW (L/min) SPEED (r/min) 200PHD 100PHD TORQUE (Nm) PRESSURE (Bar) 200PHD 100PHD 100PHD 200PHD 300PHD 100PHD 200PHD 300PHD L/min r/min L/min r/min L/min r/min Bar Nm Bar Nm Bar Nm The figures shown are theoretical and provided as a guide only. The manufacturer accepts no responsibility/liability for any direct or indirect loss caused to person(s) who use this guide. Suitable test equipment must be used to obtain accurate values
10 Earthmoving Blades E a r t h m o v i n g B l a d e s p a g e 8 The bull blade is available in two widths and with a variety of configurations. All blades are formed from high grade steel and have a pressed mouldboard and are fitted with a replaceable bolt-on reversible cutting edge. Standard bull blades have the attaching lugs welded directly to the rear of the blade ready to couple to the front end loader. When fitted with root rakes, the bull blade can be inverted through an adaptor on the rear of the blade. This will position the rake tines towards the ground, allowing ripping and removal of small tree and shrub roots from beneath the ground surface. Alternatively, when pushing up debris, the tines allow topsoil to be left behind. The bull blade can also be set up with a manual angle adjustment and a manual tilt adjustment. These are set through brackets supplied and attached to the back of the blade, allowing the operator to change from a standard configuration to either or both angle and tilt options. The bull blade can also be set up with a manual angle adjustment and a hydraulic tilt adjustment. The manual angle is set using the bracket supplied and attached to the back of the blade. The tilt is controlled through a hydraulic third service which the operator can control during use. BULL BLADE WITH MANUAL ANGLE AND HYDRAULIC TILT
11 E a r t h m o v i n g B l a d e s p a g e 9 BULL BLADE WITH ROOT RAKES Blade Rake BR Model 216BR 246BR Description Bull Blade with Root Rakes Bull Blade with Root Rakes Width 2160mm 2460mm 320kg 360kg Root rake spacing 163mm 157mm Blade Rake, Manual Angle and Tilt BRMAT Model 216BRMAT 246BRMAT Description Bull Blade Manual Angle and Tilt with Root Rakes Bull Blade Manual Angle and Tilt with Root Rakes Width 2160mm 2460mm 370kg 410kg Root rake spacing 163mm 157mm Blade Rake, Manual Angle and Hydraulic Tilt BRHAT Model 216BRHAT 246BRHAT Description Bull Blade Manual Angle, Hydraulic Tilt with Root Rakes Bull Blade Manual Angle, Hydraulic Tilt with Root Rakes Width 2160mm 2460mm 450kg 490kg Root rake spacing 163mm 157mm Blade Rotation 1 Blade Rotation 2
12 Hay Handling Attachments Round Bale Spike RBS Model 100RBS 125RBS Round BALE Spike The round bale spike can be used to spike into the flat side of a round bale. The attachment is fitted with two tines to ensure the bale is unable to rotate while being handled. The round bale spike has the loader attachment lugs welded directly to the attachment frame making it a stand-alone attachment to allow for quick and efficient changeover. 94kg 91kg Width 1340mm mm Tines x usable length Other tines available 2 x 970mm (Conus I) 2 x 680mm (Conus I) 2 x 970mm (Conus I) 2 x 680mm (Conus I) Round Bale Fork RBF Round BALE FORK The round bale fork can be used to spike into the flat side of a round bale or the tines can be slid under the bale allowing the tines to cradle the bale (great for older or loose bales that need to be supported). The attachment is fitted with two tines so that the bale is unable to rotate during transport or stacking. The round bale fork has the loader attachment lugs welded directly to the attachment frame making it a stand-alone attachment to allow for quick and efficient changeover. Model Width Tines x usable length Other tines available 125RBF 108kg 1100mm-1250mm 2 x 1110mm (Conus II) 2 x 840mm (Conus II) 2 x 1260mm (Conus II) H ay H a n d l i n g A t t a c h m e n t s p a g e 1 0 DUAL ROUND BALE SPIKE The dual round bale spike can carry 2 and up to 3 round bales when used with the back rest. Used in conjunction with the three-point linkage dual round bale spike attached to a front end loader you will be able to move 4 and up to 6 round bales at once. The option of using both dual round bale spikes together will save you time and fuel costs by reducing tractor movements when moving bales. Dual Round Bale Spike RB2C Model 100RB2C 126kg Tines x usage length 4 x 970mm (Conus I) Inner tine spacing 1230mm Outer tine spacing 660mm
13 SQUARE BALE SPIKE This attachment is designed to handle large square bales, but round bales may also be handled depending on the tine configuration. The attachment is fitted with four tines as standard (five tines in the extra wide square bale spike - ideal for export bales) and these are driven into the long side of the bale to give maximum support to the bale while being handled. The square bale spike has the loader attachment lugs welded directly to the attachment frame, making it a stand-alone attachment to allow for quick and efficient changeover. A backrest extension is available as an option with this attachment to enable additional bales to be handled safely. The square bale spike can be fitted with a number of tine configurations to suit your individual needs. All tines fit into a tapered sleeve and are removable. Square Bale Spike SBD Model Width Tines x usable length Tine spacing 100SBD 102kg 1710mm 2 x 970mm (Conus I) 2 x 680mm (Conus I) 535mm Extra Wide Square Bale Spike SBDE (suit export bales) Model 100SBDE Width Tines x usable length Inner tine spacing Outer tine spacing 138kg 1910mm 5 x 1110mm (Conus II) 420mm 480mm H ay H a n d l i n g A t t a c h m e n t s p a g e 1 1 Back Rest BR Model 125BR 18kg Width 1230mm Height 1380mm Back Rest Extension The back rest has the ability to provide support to loads during handling that are higher than the attachment frame. The back rest extension quickly and simply slides in or out of the top section of the attachment frame, extending the effective height. Compatible with all hay handling attachments. Hay Tines It is important that hay tines are replaced with genuine Challenge hay tines to ensure that safety standards are met. Some hay tines on the market are made from inferior grade steel and may fail. Straight Cranked Curved Full length 810mm 810mm 1100mm 1100mm 980mm 1250mm 1400mm 800mm 680mm Usable length 680mm 670mm 970mm 960mm 840mm 1110mm 1260mm 670mm 550mm Conus I II I II II II II I I
14 Silage Attachments ROUND WRAPPED SILAGE GRAB The round wrapped silage grab has been designed to allow the efficient handling of wrapped silage bales and round hay bales. The large smooth surface area helps prevent damage to the wrapping material on silage bales. This attachment requires a third hydraulic control circuit, through which the grab arms are controlled. Bringing the arms together around the wrapped silage or round bale allows it to be handled, transported and stacked. The round wrapped silage grab also allows you to rotate the bale through 90 so that you can stack bales on their flat or round sides. An additional cylinder position hole allows the grab arms to be adjusted, allowing most bale sizes to be handled securely and safely. Round Wrapped Silage Grab RSG Model 200RSG Bale sizes Up to 1800mm 224kg SQUARE WRAPPED SILAGE GRAB The square wrapped silage grab has been designed to allow the efficient handling of both wrapped square silage bales and square hay bales. The large smooth surface area helps prevent damage to the wrapping material on silage bales. This attachment requires a third hydraulic control circuit, through which the grab arms are controlled. Bringing the arms together around the wrapped silage or square bale allows it to be handled, transported and stacked securely and safely. Square Wrapped Silage Grab SSG Model 180SSG 246SSG Bale sizes 3 to 6 6 to 8 374kg 412kg Note: Optional back rest extension S i l a g e A t t a c h m e n t s p a g e 1 2 WRAPPED SILAGE HANDLER The wrapped silage handler has the ability to handle wrapped silage bales as well as round hay bales. This attachment requires a third hydraulic control circuit to activate the hydraulic cylinder, enabling the arms to open and close as required. With the arms in the open position and close to the ground, the attachment is driven forward under the bale. Closing the arms, the large diameter steel tubes roll around the outside of the bale without damaging the plastic, allowing it to be transported. When handling unwrapped hay or straw bales the tubes can be unpinned and slid off, exposing heavy duty tines which can then be driven into the face of the bale. The adjustable arms allow any size bale to be handled securely and safely. Tines fit into a tapered sleeve and are removable. Wrapped Silage Handler RSH Model 100RSH 195kg Length of arms 1120mm Tines x usage length 2 x 1110mm (Conus II)
15 SILAGE GRAB BUCKET The silage grab bucket has been designed to handle loose or fine chop silage and is ideal for cleaning up other loose materials such as straw. Having a bucket style bottom, this attachment allows for clean and easy handling of this type of material. After it is driven into the silage face, the attachment can be crowded back like a conventional bucket, ensuring maximum fill with the tines holding and containing the material being handled. Optional end plates are available which simply bolt to the side profile if extremely loose material is to be handled. This attachment requires a third hydraulic control circuit to activate the grab portion of the attachment. All tines fit into a tapered sleeve and are removable. POWER SILAGE GRAB The power silage grab has been designed to handle pit silage easily and safely. This attachment requires a third hydraulic control circuit to activate the grab portion of the attachment. The tines are forced through the silage in a circular motion using minimal effort and ensuring an efficient cut, clamping the material in the attachment. The tines are spaced to ensure wastage from material falling through the tines is kept to a minimum. All tines fit into a tapered sleeve and are removable. Silage Grab Bucket SGB Model 156SGB 186SGB 216SGB 310kg 360kg 410kg Width 1560mm 1860mm 2160mm Depth 800mm 800mm 800mm Volume/capacity 0.73m³ / 449kg 0.88m³ / 541kg 1.03m³ / 633kg Tines x usable length 6 x 550mm 7 x 550mm 8 x 550mm Tine spacing 252mm 260mm 260mm Note: Volume and capacity based on 615 kg/m³ - 30% dry volume. Power Silage Grab PSG Model 150PSG 180PSG 253kg 304kg Width 1500mm 1800mm Depth 860mm 860mm Volume/capacity 0.64m³ / 394kg 0.76m³ / 467kg Bottom tines x usable length 9 x 670mm 11 x 670mm Tine spacing 175mm 175mm Top tines x usable length 6 x 550mm 7 x 550mm Tine spacing 251mm 260mm Tines on side x usable length 2 x 680 (Conus I) 2 x 680 (Conus I) Note: Volume and capacity based on 615 kg/m³ - 30% dry volume. S i l a g e A t t a c h m e n t s p a g e 1 3 SILAGE FORK The silage fork is ideal for handling pit silage and other light materials. This attachment has the loader attachment lugs welded directly to the attachment frame making it a stand-alone attachment to allow for quick and efficient changeover. The tines are fitted into a tapered sleeve and are removable. Silage Fork SF Model 150SF 180SF 111kg 125kg Width 1510mm 1810mm Tines x usable length 9 x 670mm 11 x 670mm Tine spacing 175mm 170mm
16 Silage Attachments SILAGE SHEAR GRAB The silage shear grab is designed to cut silage blocks from the silage pit, leaving a smooth face that is sealed to prevent spoilage. This attachment requires a third hydraulic control circuit to activate the grab/cutting portion of the attachment, which features a hardened serrated front knife and hardened plain knives on the sides. The rounded front profile of the grab is forced through the silage in a circular motion, reducing the cutting force required and ensuring an efficient, clean cut. The two heavyduty hydraulic cylinders provide ample cutting force and the attachment is fitted with quality heavy-duty tines to accommodate this. All tines fit into a tapered sleeve and are removable. Silage Shear Grab SS Model 140SS 170SS 370kg 460kg Width 1400mm 1700mm Depth 880mm 880mm Volume/capacity 0.81m³ / 498kg 0.98m³ / 602kg Opening 730mm 730mm Bottom tines x usable length 9 x 670mm 11 x 670mm Tines on side x usable length 2 x 670mm (Conus II) 2 x 670mm (Conus II) Tine spacing 125mm 129mm Note: Volume and capacity based on 615 kg/m³ - 30% dry volume. Other Lifting Attachments BULK BAG LIFTER The bulk bag lifter has been designed to safely handle fertilizer bags with four lifting straps. Maximum lift height is achieved by the high strapping lugs allowing the bag to be attached to the bulk bag lifter while the attachment is on the ground. The four strapping points ensure stability of the bag during handling. S i l a g e A t t a c h m e n t s p a g e 1 4 Bulk Bag Lifter BBL Model 100BBL 146kg Height 1520mm Maximum load 1000kg APPROVED LIFTING CHAIN The approved lifting chain provides a safe and legal lifting point on a Challenge loader. The rated operating load is the same as that of the tractor/loader combination up to a maximum of 2.6 tonne at 60.
17 Other Lifting Attachments Pallet Fork MCPF Model 125MCPF Width Maximum load Fork length 195kg 1105mm-1250mm 2500kg 1075mm POWER LOG GRAB The power log grab has loader attachment lugs welded directly to the attachment frame making it a stand-alone attachment to allow for quick efficient changeover. This attachment requires a third hydraulic control circuit to activate the grab arm of the attachment. Additional pallet forks are available to increase the load bearing surface area. C Pallet Fork The pallet fork has the loader attachment lugs welded directly to the attachment frame to allow simple coupling and uncoupling to the loader. The fork arms are made from alloy steel and are forged to ensure maximum load carrying capacity. This attachment can be fitted with an optional back rest extension. O Width: Measurement of the overall width of the carriage in millimetres. Maximum Opening (O): Maximum distance in millimetres between the tines and power log grab arm when open. Optional Back Rest Extension compatible with the Pallet Fork Power Log Grab PLG Model 100PLG Width Maximum opening (O) Minimum close (C) 240kg 1350mm 870mm 210mm O t h e r L i f t i n g A t t a c h m e n t s p a g e 1 5 Minimum Close (C): Minimum distance in millimetres between the carriage and power log grab arm when closed. Aus Hitch QUICK COUPLER The Aus Hitch quick coupler is a specifically designed attachment system used for coupling all attachments, using the Aus Hitch system, quickly and efficiently. The quick coupler uses a single lever action to disengage the locking pins from the attachment and has a spring return auto lock function when reattaching to an attachment. The Aus Hitch is designed with much larger and stronger locking pins in comparison to the Euro Hitch. EURO Hitch QUICK COUPLER The Euro Hitch quick coupler has been developed to allow those customers, who may have previously purchased European-style attachments that suit some of the European-manufactured loaders, the ability to retain those attachments and use them on their Challenge front end loader. The quick coupler uses a single lever action to disengage the locking pins from the attachment and has a spring return auto lock function when reattaching to an attachment. 70kg 84kg
18 Three-Point Linkage Attachments THREE-POINT LINKAGE ROUND BALE SPIKE The three-point linkage round bale spike tines can be driven into the flat side of a round bale. The attachment is fitted with two tines to ensure the bale is unable to rotate while being handled. Tines fit into a tapered sleeve and are removable. Three-Point Linkage Round Bale Spike Model 3PLRBS Width Linkage category 50kg 770mm Tines x usable length 2 x 970mm (Conus I) Tine spacing II 547mm Other tines available 2 x 680mm (Conus I) THREE-POINT LINKAGE DUAL ROUND BALE SPIKE The three-point linkage dual round bale spike can carry 2 and up to 3 round bales when used with the extension. Used in conjunction with the dual round bale spike attached to a front end loader you will be able to move 4 and up to 6 round bales at once. The option of using both dual round bale spikes together will save you time and fuel costs by reducing tractor movements when moving bales. Three-Point Linkage Dual Round Bale Spike Model 3PLDRBS Width Linkage category 120kg 2680mm Tines x usable length 4 x 970mm (Conus I) Inner tine spacing Outer tine spacing II 1230mm 660mm T h r e e - P o i n t L i n k a g e A t t a c h m e n t s p a g e 1 6 THREE-POINT LINKAGE SQUARE BALE SPIKE The three-point linkage square bale spike is designed to handle large square bales. The attachment is fitted with four tines as standard and these are driven into the long side of the bale to give maximum support to the bale while being handled. This attachment can be fitted with a number of tine configurations to suit your individual needs. All tines fit into a tapered sleeve and are removable. Three-Point Linkage Square Bale Spike Model 3PLSBS Width Linkage category Tines x usable length Tine spacing 80kg 1710mm II 2 x 970mm (Conus I) 2 x 680mm (Conus I) 535mm
19 G Series Rear End Grader The G Series graders can be used for maintenance and repair of agricultural roads and other farm related operations. The blade can also be reversed for back blade work. The rear end graders have been designed specifically to suit tough Australian conditions. The large high tensile 100mm rotation pin ensures correct alignment and maximum forces can be sustained. The main boom structure has been designed to handle the large horse power of todays tractors. The hydraulic hoses are conveniently routed to the tractor remote connections. The graders are equipped with two heavy duty, pneumatic depth wheels. The blade angle and rotation plate is fixed by two large machined brackets that take all the forces submitted through the blade. The front hitch is compatible with category 2 and 3 linkage and category 3 quick hitch system. The grader blades are constructed of 8mm high grade steel with replaceable purpose built toughened wear edges. This attachment also includes two heavy duty frame stands that allow stable and easy storage of the rear end grader. T h r e e - P o i n t L i n k a g e A t t a c h m e n t s p a g e 1 7 Rear End Grader G Model G24 G30 G36 Horse power range 90hp-180hp 90hp-180hp 180hp-300hp Linkage category 2, 3, 3QH 2, 3, 3QH 2, 3, 3QH Blade width 2400mm 3000mm 3600mm Blade height 600mm 600mm 600mm Blade angle Blade tilt Offset adjustment 830mm 830mm 830mm Blade thickness 8mm 8mm 8mm 1070kg 1120kg 1220kg
20 Counterweights Three-Point Linkage Counterweight A major safety factor in the operation of a front end loader/tractor unit is the stability of the machine whilst lifting and transporting a load. After fitting a loader, the centre of gravity of the tractor is moved forward. When a load is raised, this combined centre of gravity is moved further forward and higher, potentially moving the centre of gravity outside the base triangle of the tractor, causing instability both longitudinally and laterally. Along with instability, there are high loads placed on tractor frontend components such as tyres, rims and axle. Traditionally, tractor owners have added ballast to increase the stability of the tractor when a loader is fitted by adding liquid fill to the rear tyres, or fitting rear wheel weights. Although the addition of liquid fill or rear wheel weights may aid stability, neither will reduce the high front axle load when using the front end loader on the tractor. Also, an unnecessarily large amount of weight is required to achieve a result, increasing total vehicle mass considerably. The three-point linkage counterweight is designed to enhance the performance of the tractor/loader combination by providing suitable ballast behind the rear axle. Applying weight on the three-point linkage of the tractor will provide the greatest counterbalancing effect as it applies a downward force behind the rear axle, reducing the weight carried by the front tyres, rims and axle. The threepoint linkage counterweight will not only reduce the front axle load but will also move the centre of gravity of the tractor/loader combination rearwards, and lower, to maintain stability and ensure safe, effective performance. The three-point linkage counterweights are supplied without ballast and should be filled with concrete to achieve the designed operational weights. Each tractor and loader specification should be considered when selecting the appropriate counterweight. Challenge Implements strongly recommends the use of a three-point linkage counterweight to improve both the safety and performance of your Challenge loader/tractor unit. Challenge Implements has undergone an independent evaluation to ensure that the company complies with the Tractor & Machinery Association of Australia (TMA) code of practice for manufacture and supply of agricultural front end loaders. Downward force applied by linkage counterweight Front axle load reduced and stability increased Counterweight for low horse power tractors C o u n t e r w e i g h t s p a g e 1 8 FULCRUM Three-Point Linkage Counterweight CW Model 14CW 30CW 46CW 125CW (empty) 45kg 70kg 155kg 380kg (full) 360kg 760kg 1220kg 3270kg Width 495mm 660mm 1015mm 1610mm Height 645mm 790mm 950mm 1210mm Depth 475mm 460mm 500mm 715mm Volume 0.14m m m m 3 Linkage category I I II III Standard hitch Yes Yes Yes Yes Quick hitch No No No Yes
21 Manufacturing Technology Challenge Implements has a strong commitment to continuous improvement, research, and development and has adopted state-of-the-art manufacturing processes using robotic welding, laser cutting and multi-head profile cutting machines as an integral component in the fabrication of their attachments. Challenge Implements use two robotic welding machines, including dual robots controlling two welding torches simultaneously, allowing both welding torches to work on the one product at any one time. The latest robotic system is the first dual robot of this type to be installed in Australia. These robotic systems use weld seam tracking, an advanced system that allows the robot to correct minor errors in joint alignment, improving quality and accuracy. All Challenge Implements attachments are designed using 3D CAD software, allowing for computer-generated profiles to be accurately cut using laser or profile cutting machines. Using computer generated tool paths ensures consistent part manufacture and trouble-free assembly of components. M a n u f a c t u r i n g T e c h n o l o g y p a g e 1 9
22 Notes
23 Challenge Implements 100% Australian Owned
24 Challenge Implements Holdings Pty Ltd Trading as Challenge Implements ABN Leewood Drive, Orange NSW 2800 PO Box 7039, Orange NSW 2800 Phone: (02) Fax: (02) REF REV. E 11/11/13 Challenge Implements reserves the right to improve specifications and change the design of its products without prior notification. Challenge Implements designs, manufactures and supplies agricultural attachments that are intended to be used on Challenge Implements front end loaders and other front end loaders approved by the company. Challenge Implements front end loaders and attachments are made to comply with the Tractor and Machinery Association (TMA) code of practice. Attachments must not be modified and should only be used for their stated use.
front end loaders forklifts & attachments Made in Australia Page 4 Page 5 Page 6 Page 8 Page 16
front end loaders forklifts & attachments Made in Australia Page 4 Page 5 Page 6 Page 8 Page 16 front end loader Simple and easy to use Level Indicator Through Rod Tilt Rams for faster dump and crowd Vesconite
More informationLOADERS Ideal for virtually every rugged job, Woods loaders provide years of worry-free service
LOADERS Ideal for virtually every rugged job, Woods loaders provide years of worry-free service Loaders Contents Table of Contents LS-Series Loaders...4 LS72 LS84 LS96 LS96R LC-Series Loaders...5 LC96
More informationWork Tools Telehandlers
Work Tools Telehandlers Access Platform Bale Handler Buckets Carriages Forks Lifting Hook Manure Forks Material Handling Arm Self Tipping Hopper Truss Boom Caterpillar Work Tools Designed for maximum performance,
More informationattachment product catalogue
attachment product catalogue 2011 A Complete Range Handling Made Easy The Best Partner for your machine 1 THE RANGE Invest in Rata Attachments. Rata Industries has been designing and manufacturing innovative
More informationAGRICULTURE ATTACHMENTS
AGRICULTURE ATTACHMENTS TACKLE MORE TASKS WHILE MITIGATING COSTS WITH YOUR CAT MACHINE. Cat Skid Steer Loaders, Multi Terrain Loaders, Compact Track Loaders, Compact Wheel Loaders, Backhoe Loaders, Small
More informationFront loader Fendt CARGO
Front loader Fendt CARGO An unbeatable combination Fendt Vario with Fendt CARGO The new Fendt front loader Fendt CARGO offers sophisticated technology for maximum productivity. It expands the Fendt product
More informationPower Ditchers, Bale Slicer, Rock Picker, Screening Bucket
Model 400 Power Ditchers Model 600 Bale Slicer Model 500 Rock Picker Model 700 Screening Bucket remlingermfg.com ISO9001:2015 certified Our Tradition is Quality Driven and Field Proven Power Ditchers,
More informationFront loader Fendt CARGO
Front loader Fendt CARGO An unbeatable combination Fendt Vario with Fendt Cargo The Fendt front loader Fendt CARGO offers sophisticated technology for maximum productivity. As a reliable universal implement,
More informationPower Ditchers Spring Tensioned - BELT DRIVE
EMLINGER MANUFACTURING COMPANY, INC. 16394 U.S. 224 - P.O. Box 299 Kalida, Ohio 45853 419/532-3647 800/537-7370 www.remlingermfg.com ECONOMICAL TO OWN EASY TO OPERATE Series 400 - Center Cut & Offset Power
More informationLOADERS. COMPACT MX C1 MX C2 MX C3u MX C3 MX C3+ MX C4 MX C4+
LOADERS COMPACT MX C1 MX C2 MX C3u MX C3 MX C3+ MX C4 MX C4+ Connexion électro-hydraulique tracteur/chargeur à coupleurs étanches avec le MACH System. We dare to innovate: in our relationships, our techniques,
More informationAGRICULTURE ATTACHMENTS
AGRICULTURE ATTACHMENTS TACKLE MORE TASKS WHILE MITIGATING COSTS WITH YOUR CAT MACHINE. Cat Skid Steer Loaders, Multi Terrain Loaders, Compact Track Loaders, Compact Wheel Loaders, Backhoe Loaders, Small
More informationLoaders Loaders And Mounts To Fit Your Tractor. Backhoes Ability To Do Your Own Dirt Work. Attachments A Variety Of Options For Your Loader
Koyker Manufacturing INC. A division of Sioux Steel Company 200 N. Cleveland, P.O. Box 409 Lennox, SD 57039 Toll Free: (800) 456-1107 Local: (605) 647-2811 Fax: (605) 647-2813 info@koykermfg.com www.koykermfg.com
More informationMELBOURNE: BRISBANE: Ph : Fax : Ph : Fax :
www.normeng.com.au BRISBANE: Ph : 07 3376 3177 Fax : 07 3376 3201 sales@normeng.com.au www.normeng.com.au 21 Spine Street Sumner Park Queensland 4074 MELBOURNE: Ph : 03 9775 1965 Fax : 03 9770 8054 victoria@normeng.com.au
More informationFront loader. Fendt CARGO
Front loader Fendt CARGO 1 2 The Fendt CARGO front loader 3 The combination is unbeatable The Fendt front loader Fendt CARGO offers sophisticated technology for maximum productivity. As a reliable universal
More informationATTACHMENTS FOR LOADER CRANES
ATTACHMENTS FOR LOADER CRANES 2012 Rotators page KM 03 S Rotator with shaft 11 KM 04 S Rotator with shaft 11 KM 04 F Rotator with flange 11 KM 06 F Rotator with flange 12 Brick Stack Grapples KM 332V-1100
More informationPRODUCTIVE COST-EFFECTIVE RUGGED VERSATILE
PRODUCTIVE COST-EFFECTIVE RUGGED VERSATILE { } GANNON the industry workhorse HEAVY-DUTY BUCKETS SEVERE-DUTY BUCKETS DITCHING & GRADING BUCKETS LOADER BUCKETS SPECIALTY BUCKETS BOX SCRAPERS QUICK CHANGE
More informationFrontier Loader Attachments
Frontier Loader Attachments Hay and Forage Tools Material Handling Pallet Forks Hay Handling: Durable, efficient Large and Small Square Bale Forks There s no time for downtime when you ve got chores to
More informationAGRICULTURE ATTACHMENT OVERVIEW
AGRICULTURE ATTACHMENT OVERVIEW AG LOADER BUCKETS GP BUCKET 6mm high grade shell Wear plates Cutting edge 0.5-1.0m 3 capacities HIGH CAP BUCKET 6mm high grade shell Wear plates Cutting edge 0.9-1.5m 3
More informationAGRICULTURE ATTACHMENTS TACKLE MORE TASKS WHILE MITIGATING COSTS WITH YOUR CAT MACHINE.
AGRICULTURE ATTACHMENTS TACKLE MORE TASKS WHILE MITIGATING COSTS WITH YOUR CAT MACHINE. Cat Skid Steer Loaders, Multi Terrain Loaders, Compact Track Loaders, Compact Wheel Loaders, Backhoe Loaders, Small
More informationExcavator Attachments
Quick Coupler Lug Adapter Dig Bucket Clean Up Bucket Tilt Bucket Tilt Blade Hydraulic Thumb Stick Ripper Brush Rake Lift Device Guarding Excavator Attachments Brandt takes pride in designing and manufacturing
More informationStoll Loaders & Implements
Stoll Loaders & Implements Burder Ag Attachments is the exclusive distributor for Stoll in Australia. Stoll products are available through Burder s dealership network. Stoll manufactures a wide range of
More informationLEGEND ATTACHMENTS. Product Catalog (Main Office) (Tim Lake - Sales)
LEGEND ATTACHMENTS 2018 Product Catalog 218-844-5378 (Main Office) 612-360-4160 (Tim Lake - Sales) tlake@legendattachments.com www.legendattachments.com Legend Attachments 1090 Legion Road Detroit Lakes,
More information980H. Block Handler Arrangement. Engine Engine Model. Operating Specifications. Cat C15 ACERT
98H Block Handler Arrangement Engine Engine Model Gross Power Net Power Cat C15 ACERT 293 kw 398 hp 26 kw 353 hp Operating Specifications Operating Weight Implement System Maximum Operating Pressure Hydraulic
More informationAttachments For Compact Tractors with Universal Skid-Steer Hitch
compact Tractor Attachments Compact Tractor Attachments For Compact Tractors with Universal Skid-Steer Hitch Paladin offers a variety of attachments for Compact Tractors ranging in size, capability, and
More informationMINI SKID STEER ATTACHMENT LITERATURE
MINI SKID STEER ATTACHMENT LITERATURE 2 BUCKETS & BLADES When you need to power through with productivity you can be sure that you ve come to the right place. With our versatile lineup of buckets and blades,
More informationStandard Duty Cutter 3 Medium Duty Cutter 4 Heavy Duty Cutter (5, 6 & 7 ) 5 Heavy Duty Cutter (8 ) 6 Heavy Duty Cutter (10 ) 7 M-Heavy Duty Cutter (5
PRODUCT PAGE NUMBER Standard Duty Cutter 3 Medium Duty Cutter 4 Heavy Duty Cutter (5, 6 & 7 ) 5 Heavy Duty Cutter (8 ) 6 Heavy Duty Cutter (10 ) 7 M-Heavy Duty Cutter (5 & 6 ) 8 Super Duty Cutter (6 &
More informationLoader Attachments. Material Handling
Loader Attachments Material Handling Hay Handling: Durable, efficient hay tools to suit every situation. There is no time for downtime when you have chores to do. That is why you need reliable hay handling
More informationSKID STEER ATTACHMENTS. A full line of attachments to harness the versatility of your Skid Steer Loader
SKID STEER ATTACHMENTS A full line of attachments to harness the versatility of your Skid Steer Loader Skid Steer Attachments Contents Table of Contents General Purpose Buckets...4 Augers... 14 Root Grapple
More informationCOMPACT TRACTOR ATTACHMENTS
COMPACT TRACTOR ATTACHMENTS For Compact Tractors with Universal Skid-Steer Hitch Paladin Attachments is your single source for high quality Compact Tractor Attachments landscapers. Paladin offers a variety
More informationloaders U300 Series MX U303 / U304 MX U305 / U306 MX U307 / U308 MX U309 / U310 MX U312 RAISE YOUR EXPECTATIONS
loaders U300 Series MX U303 / U304 MX U305 / U306 MX U307 / U308 MX U309 / U310 MX U312 RAISE YOUR EXPECTATIONS RAISE YOUR EXPECTATIONS We dare to innovate; in our relationships, in our techniques, in
More informationAMI Wheel Loader Attachments
AMI Wheel Loader Attachments www.amiattachments.com Top View GENERAL PURPOSE To fill quickly material needs to roll. AMI angles the bucket floor up slightly helping to lift material into the bucket. Smooth
More informationGrabs and Rotators. Attachments for truck mounted crane.
Grabs and Rotators Attachments for truck mounted crane www.hyva.com Crane Attachments by Brick Stack Grapple H 332 Pallet Fork H 415 Orange Peel Grapple H 650 Clamshell Bucket H 604HPX Small Volume Clamshell
More informationAMI Wheel Loader Attachments
AMI Wheel Loader Attachments www.amiattachments.com Top View SPADE NOSE Make your point with the AMI severe duty spade nose bucket. Built for handling rock in mining and quarry applications, the AMI spade
More informationLANDSCAPE EQUIPMENT. A full line of tools to tackle a variety of yard, garden and landscape projects
LANDSCAPE EQUIPMENT A full line of tools to tackle a variety of yard, garden and landscape projects Landscape Equipment Contents Table of Contents Box Scrapers...4 From the reinforced steel A-frame to
More informationCOMMERCIAL EQUIPMENT. Snowblowers Triplex Finishing Mower Stump Grinder Brush Grapple Rotary Sweep Snow Blade Rear Blade Quick Hitch Loader Attachment
COMMERCIAL EQUIPMENT Snowblowers Triplex Finishing Mower Stump Grinder Brush Grapple Rotary Sweep Snow Blade Rear Blade Quick Hitch Loader Attachment Allied by Farm King Commercial Equipment: snowblowers,
More informationGRABS AND ROTATORS ATTACHMENTS FOR TRUCK MOUNTED CRANE.
GRABS AND ROTATORS ATTACHMENTS FOR TRUCK MOUNTED CRANE www.hyva.com CRANE ATTACHMENTS BY Brick Stack Grapple H 332 Pallet Fork H 415 Orange Peel Grapple H 650 Clamshell Bucket H 604HPX Small Volume Clamshell
More informationFront loaders IRON - STEEL - GOLD - TITANIUM.
Sigma4 S.p.A. Via Madrara, 2/1 48026 Russi (RA) Italy Tel. +39 0544-585411 _ Fax +39 0544-585415 www.sigma4.it Front loaders IRON - STEEL - GOLD - TITANIUM The perfection of the detail A winning choice
More informationBackhoe Range. For Tractors from 15HP
Backhoe Range For Tractors from 15HP LEWIS Backhoe Range The LEWIS range of backhoes are specifically designed to fit most makes of tractors from 15HP compact tractors up to 60+HP agricultural tractors.
More informationGet More Out Of Your Land With Frontier Landscape Equipment
Get More Out Of Your Land With Frontier Landscape Equipment Rear Blades Box Blades Soil Pulverizers Core Aerators Turf Renovators Landscape Rakes Keep your land looking clean Landscape Rakes Your needs
More informationAgriculture. Your handling partner
Agriculture Your handling partner HELPING you Whether you breed dairy or suckler cows, grow crops or run a farming business, run a stud farm or are part of a farm machinery co-operative, you have many
More informationAMI Wheel Loader Attachments
AMI Wheel Loader Attachments www.amiattachments.com Top View SPADE NOSE Make your point with the AMI severe duty spade nose bucket. Built for handling rock in mining and quarry applications, the AMI spade
More informationFEEDING BUCKETS MX BD1202 MX BD1402 MX BD2002 MX BD2402 MX BD3102
FEEDING BUCKETS MX BD1202 MX BD1402 MX BD2002 MX BD2402 MX BD3102 We dare to innovate; in our relationships, in our techniques, in our products and services. Together with our business partners, our ambition
More informationCAT MINI EXCAVATOR ATTACHMENT OPTIONS
CAT MINI EXCAVATOR ATTACHMENT OPTIONS Get Multiple Machines Out of One For more information, visit Cat.com/attachments or contact your local Cat dealer. AEXQ1584-02 March 2018 2018 Caterpillar. All Rights
More informationCAT MINI EXCAVATOR ATTACHMENT OPTIONS
CAT MINI EXCAVATOR ATTACHMENT OPTIONS Get Multiple Machines Out of One For more information, visit Cat.com/attachments or contact your local Cat dealer. AEXQ1584-01 December 2015 2015 Caterpillar. All
More informationAsk for genuine Bobcat buckets.
24 bucket Don t accept imitations. Ask for genuine Bobcat buckets. Bobcat buckets are built tougher to work harder. For lighter duty jobs: General Purpose & Dirt Buckets For daily use with smaller Bobcat
More informationJCB ATTACHMENTS AGRICULTURAL ATTACHMENTS. Stronger, lighter, more durable.
JCB ATTACHMENTS AGRICULTURAL ATTACHMENTS Stronger, lighter, more durable. MAXIMUM PERFORMANCE MAXIMUM EFFICIENCY. JCB HAS ALWAYS UNDERSTOOD THAT, WHEN IT COMES TO AGRICULTURAL MACHINERY, ONLY THE VERY
More informationSEVERE SERVICE SKID STEER BUCKETS
SEVERE SERVICE SKID STEER BUCKETS GROUP 6 2200 LB. AND OVER OPERATING CAPACITY BOBCAT 873/953/963 NH L865/LX865/LX885/LX985/LS190 CASE 85XT/90XT/95XT 435 445 450 465 SCAT TRAK 2300D CAT 902/906/908 SWINGER
More informationRound Bale Wrappers
Bale Wrapper Specialists Round Bale Wrappers www.itanco.com Tanco Round Bale Wrappers For contractors and farmers around the world, Tanco is the choice for round bale wrapping. Over twenty years experience
More informationFRONT LOADER TURNS LITTLE INTO BIG!
FRONT LOADER TURNS LITTLE INTO BIG! 2 ADDED VALUE FOR SMALL TRACTORS Confi ned spaces, small areas and narrow alleys. Small tractors feel comfortable here. It s all about manoeuvrability with simultaneous
More informationThere s no better choice than Premier.
There s no better choice than Premier. PREMIER POWER Premier Agricultural Attachments are designed to utilize the power of the host machine most efficiently, turning them into high performance work tools.
More information512, 522, AND 542 LOADERS
9-5-1 512, 522, AND 542 LOADERS 5325 Tractor with 542 Self-Leveling Loader and MX7 Rotary Cutter 5425 Tractor with 542 Loader and 49 Backhoe 9-5-2 512, 522, and 542 Loaders 5325N Cab Tractor with 522 Loader
More informationFence Building Attachments Consistently delivering high performance
Designed. Engineered. Remarkable Value. Fence Building Attachments Consistently delivering high performance www.worksaver.com Engineered, Designed and Manufactured in the USA Our Post Hole Diggers Dig
More informationAdapters, Augers, Backhoes & Brooms
Mini Attachments Bradco & McMillen, Delhi, IA 52223 PH: (800)922-2981 FX: (563)922-2700 1805 2nd Avenue SW, PH: (800)437-9779 FX: (701)252-1978 Adapters, Augers, Backhoes & Brooms Bradco Adapters Auger
More informationB26 KUBOTA DIESEL TRACTOR
KUBOTA DIESEL TRACTOR B B26 More versatile than most tractors in its class, the streamlined B26 is compact, yet has the power and high-end features you need to accomplish a wide array of tasks. *This information
More informationVersaHANDLER Telescopic Tool Carriers
VersaHANDLER Telescopic Tool Carriers Bobcat VersaHANDLER TTC The VersaHandler Telescopic Tool Carrier combines the speed, agility and strength of a skid-steer with extended reach to handle a wide variety
More informationVALTRA FRONT LOADERS VALTRA N SERIES YOUR WORKING MACHINE
VALTRA FRONT LOADERS VALTRA N SERIES YOUR WORKING MACHINE SPECIAL FEATURES FOR PRODUCTIVE WORK Front loader features Valtra front loaders are an integral part of the tractor, tailored to the customer s
More informationAttachment Lineup. You have a lot of choices in attachments; they re all in here. Make more money with your compact equipment.
Attachment Lineup You have a lot of choices in attachments; they re all in here. Make more money with your compact equipment. Find products you didn t know existed. Compact Excavators Augers Breakers Quick
More informationCOMPACT TRACK LOADERS PRODUCT RANGE
COMPACT TRACK LOADERS PRODUCT RANGE TEREX COMPACT TRACK LOADERS WILD THINGS FAST, POWERFUL, VERSATILE. Terex compact track loaders (CTL s) excel due to the many ways in which they can be used on the widest
More informationLOADERS. T400 series MX T406 MX T408 MX T410 MX T412 MX T414 MX T417 MX T418 RAISE YOUR EXPECTATIONS
LOADERS T400 series MX T406 MX T408 MX T410 MX T412 MX T414 MX T417 MX T418 RAISE YOUR EXPECTATIONS RAISE YOUR EXPECTATIONS We dare to innovate; in our relationships, in our techniques, in our products
More informationS S T F E O S T S L EMPOWER YOUR TRACTOR!
ARTILLIAN.COM T E K R M E O T F T Y E L L E PA APPAttLachments GAnRd Other TM EMPOWER YOUR TRACTOR! TM (508) 459-4394 Make itwork for you. Artillian Pallet Fork ystems work seamlessly with John Deere,
More informationCOMPACT TRACTOR RANGE JIVO (2025) - emax 25 - MAX 28 - MAX 36
COMPACT TRACTOR RANGE JIVO (2025) - emax 25 - MAX 28 - MAX 36 MAX 28 - MAX 36 REFINEMENT AT IT S BEST DESIGNED TO MAINTAIN 5-20 ACRE PLOTS Offers a larger bucket size, stronger lifting, perfect for Nurseries.
More informationSnowblowers Triplex Finishing Mower Stump Grinder Brush Grapple Rotary Sweep Snow Blade Rear Blade Quick Hitch Loader Attachment COMMERCIAL EQUIPMENT
Snowblowers Triplex Finishing Mower Stump Grinder Brush Grapple Rotary Sweep Snow Blade Rear Blade Quick Hitch Loader Attachment COMMERCIAL EQUIPMENT Allied by Farm King Commercial Equipment: snowblowers,
More informationPH SERIES PH1000F-2000F SERIES. Heavy-duty rigid and foldable power harrows
KUBOTA PH POWER HARROWS PH1000-3000 SERIES PH1000F-2000F SERIES Heavy-duty rigid and foldable power harrows HEAVY-DUTY RIGID AND FOLDABL 2 Heavy-Duty Technology for Tough Conditions To meet the ever increasing
More informationFull products line 2014
Full products line 2014 937-2 Taegock-ri, Buk-myun, Jeongeup, Jeonbuk, Korea 580-924 Tel : 82-63-5322700 Fax: 82-63-2144175 URL: www.cowloader.co.kr or www.bawoocompany.co.kr E-mail : skid2000@cowloader.co.kr
More informationATTACHMENTS FOR LOADER CRANES
ATTACHMENTS FOR LOADER CRANES 2014 1 KINSHOFER Attachments Quality in Action Brick Stack Grapple KM 332 Universal Fork KM 461 Orange Peel Grapple KM 650 Clamshell Bucket KM 604HPX Clamshell Bucket with
More informationSide Cutter Kit (Left and Right - fits all 68", 72", 80" Buckets) 48" Pallet Fork
Side Cutter Kit (Left and Right - fits all 68", 72", 80" Buckets) These Bolt On Side Cutters (BOSC) greatly extend bucket service life and improve penetration power into hard packed soil or stock piled
More informationBobcat Backhoe Attachments
Backhoe Attachments M06 4 Bobcat Backhoe Attachments Turn your loader into a powerful part-time excavator. Ideal for landscaping, nursery work, sewage systems, septic tanks, water lines, power lines and
More informationUTILITY FARMALL U SERIES TRACTORS
UTILITY FARMALL U SERIES TRACTORS 2 READY TO WORK AS HARD AS YOU. Since 1923, the Farmall tractor name has meant power, performance, durability and value. The utility Farmall U tractors offer the ultimate
More informationSOLVING YOUR TREE AND BRUSH PROBLEMS
SOLVING YOUR TREE AND BRUSH PROBLEMS SINCE 1992 Our Revolutionary Products Let You Reclaim Your Pastures, Fields & Fence Rows From Unwanted Trees and Limbs. THE ORIGINAL SINCE 1992 TELECLIPPER TC6451 Our
More informationBUTT-N-TOP GRAPPLE FEATURES & BENEFITS: STANDARD SPECIFICATIONS: OPTIONS: Continued on next page»
BUTT-N-TOP GRAPPLE Weldco-Beales Manufacturing s Butt-n-Top Grapples load, unload, sort, and pile tree length wood with a log loader or standard excavator machine configuration. FEATURES & BENEFITS: Individually
More informationCOMPACT DISC HARROW HELIODOR 9
COMPACT DISC HARROW HELIODOR 9 2 Versatility is the trump card Compact disc harrows have revolutionised modern agriculture for more than ten years now. No other soil cultivation implement combines a comparable
More informationCompact Tracked Loaders. Product Range
Compact Tracked Loaders Product Range More productivity, less effort n Get more done in a day The undercarriage of our compact tracked loaders provides high pushing force and large lifting capabilities,
More informationQuick-drop removable beaters remove in minutes, converting your spreader into a rear discharge trailer for stockpiling or windrowing.
www.tubeline.ca VERTICAL BEATER MANURE SPREADERS CAPACITIES MODEL 375RS 12 Ton / 410 heaped cu. ft. MODEL 450 13 Ton / 453 heaped cu. ft. MODEL 525RS 15 Ton / 555 heaped cu. ft. MODEL 600 17 Ton / 593
More informationFence Building Attachments Consistently delivering high performance
Designed. Engineered. Remarkable Value. Fence Building Attachments Consistently delivering high performance www.worksaver.com Engineered, Designed and Manufactured in the USA Worksaver Worksaver with over
More informationTRACTOR - LOADER ATTACHMENTS
2017 TRACTOR - LOADER ATTACHMENTS COMPACT BALE GRAB Identification Code: HM-JDBALEGRAB MUCK FORK Identification Code: HM-JD1250MF / 1500MF MUCK GRAB Identification Code: HM-JD1250MG / 1500MG BUCKET GRAB
More informationConstruction Implements Depot, Inc. (CID) was founded in 2003 with a combined experience of over 30 years in skid steer attachments. Located in Denton, North Carolina, USA, we are committed to providing
More informationCTSERIES CT28 CT36 CT41 CT47 SYNCHRO SHUTTLE I HYDROSTATIC
CTSERIES CT28 CT36 CT41 CT47 SYNCHRO SHUTTLE I HYDROSTATIC Power and Performance The Perfect Fit The McCormick CT a new breed of power in the compact line of tractors With four horsepower sizes offered
More informationHP MF4600. Proven power and efficiency
80-100 HP MF4600 Proven power and efficiency 2 3 Big engine muscle from just 3-cylinders Torque is the key to an engine s ability to work. Torque turns the gears in the transmission. Torque digs your tyres
More informationNew Zealand. Punches well above its weight. Series II Expander with Super Pro Base. (Optional Safety Guarding not shown)
New Zealand Punches well above its weight Series II Expander with Super Pro Base (Optional Safety Guarding not shown) www.kinghitter.com PRODUCT UPDATES Series I - RANCHER Multi-Shift Base 20 Side Shift
More informationFORKS & SPEARS. Endless Attachments FORKS & RELATED ATTACHMENTS
Endless Attachments Change the attachment to change the machine. Manual tasks traditionally done by many people are now carried out by Dieci rough terrain telescopic handlers. One skilled operator with
More information7580/7590 4WD Series Tractors. No.1 TRACTOR COMPANY IN THE WORLD BY VOLUME #
7580/7590 4WD Series Tractors No.1 TRACTOR BY VOLUME # COMPANY IN THE WORLD 7580/7590 4WD Series Tractors SPECIFICATIONS ENGINE Compression Ratio Cylinders Displacement cc Engine HP (kw) @ rpm ELECTRIC
More informationCat MINI HYDRAULIC EXCAVATORS
MINI HYDRAULIC EXCAVATORS Cat match the machine to the job. Whether quarry, construction site or landscaping job, they focus the full power and performance of the machine on the task at hand. Features:
More informationLandscaping Attachments
Landscaping Attachments Skid Steer Compact Track Backhoe Compact Wheel Wheel SINCE 1842 AUGER Tackle fence work, foundations, and drainage work with a versatile auger. + + Auger options include various
More informationJOHN BERENDS IMPLEMENTS Pty. Ltd.
Product JOHN BERENDS IMPLEMENTS Pty. Ltd. AGRICULTURAL ENGINEERS (Incorporating Gibbins-Rawling) 130 Frankston-Dandenong Road, Dandenong South, Victoria 3175 Australia Phone (03) 9791 2494 Fax (03) 9794
More informationSERIES 04 DIAMOND HARROW PRODUCT MANUAL FOR SECTIONS & SETS
SERIES 04 DIAMOND HARROW PRODUCT MANUAL FOR SECTIONS & SETS TABLE OF CONTENTS Welcome Note 4 Safety 5 Usage Information 7 Normal Packaging 9 Assembly Instructions 10 Operating Instructions 13 Series 04
More informationTHE TOUGHEST IMPLEMENTS FOR THE TOUGHEST TRACTORS
THE TOUGHEST IMPLEMENTS FOR THE TOUGHEST TRACTORS 3 Point Std Duty Cutters 3 Point Medium Duty Cutters Quick hitch ready for a speedy clip on & off Round deck with channel reinforcements for extra deck
More informationDesign that improves your profitability Quicke loaders and implements ENNA
Design that improves your profitability Quicke loaders and implements ENNA 2 A front loader to make you proud Isn t it great that recurrent feeling that you have made the right choice? You notice it in
More informationCheck us out on-line! INSTRUCTION MANUAL. Scan with your smartphone to watch in use videos
INSTRUCTION MANUAL http://www.youtube.com/ user/betterbuiltco Scan with your smartphone to watch in use videos Check us out on-line! DAWS MANUFACTURING COMPANY, INC. www.dawsbetterbuilt.com 8811 GROW DR
More informationROBOCUT MORE THAN JUST A MOWER UNRIVALLED FUNCTIONALITY REMOTE CONTROL CLEAN-FIX RADIATOR MATRIX
32 33 MORE THAN JUST A MOWER Far more than just an all-terrain mowing machine, comes with a choice of seventeen new attachments, transforming it into a remote control work platform that boosts safety,
More informationData sheet GT950 C Model. Code. Technical data. Optional. Attachments
Data sheet Model Code Technical data Engine Yanmar Cylinders/power 3 cylinder 49 HP diesel R.P.M 3000 Cooling water Tank autonomy 33 l Transmission 4 D Direct Drive Max. speed 25 km/h Transmission torque
More informationMulching. Attachments BULL HOG FORESTRY MULCHERS
BULL HOG Mulching Attachments FORESTRY MULCHERS The Bull Hog Durability Fecon s Bull Hogs provide durability that is known and expected in the mulching industry. Leading with the strongest Severe-Duty
More informationProduct Catalogue. Version
Product Catalogue Version 1.0-2017 sales@lionforgeindustries.com An Introduction to Simplement The Simplement System is our Patent Pending receiver/hitch unit and modular implement system. This product
More informationBobcat T870 Compact Track Loader
Compact Track Loader The T870 is Bobcat s largest compact track loader ever manufactured. The 12 foot lift height makes it the highest lifting Compact Track Loader on the market. This machine provides
More informationMUNICIPAL ATTACHMENTS
MUNICIPAL ATTACHMENTS www.amiattachments.com GRAPTOR BUCKET When you need to pick up large, heavy objects or grab bucketfuls of debris, get a tighter grip on productivity with AMI s Graptor Bucket. The
More informationBACKHOE LOADERS CONTENTS
BACKHOE LOADERS CONTENTS Features...............................-1 Specifications...........................-3 416E:......................-6 Lift Capacities.........................-8 420E/420E IT:......................-9
More informationDrum Handling. Drum Transporter and Pouring Stand. Drum Trolley and Pouring Stand. Low Loading Drum Carrier Capacity 250kg.
62 Drum Transporter and Pouring Stand For 210 litre steel drums Capacity 350kg Welded steel construction. Removable 2-position handle Wheels: 2 x 400 mm dia. 2 x 160mm dia. castors, with solid rubber tyres.
More informationCOMPACT EXCAVATORS ZERO-TAIL-SWING 170Z 270Z 350Z 450Z 800Z
COMPACT EXCAVATORS ZERO-TAIL-SWING 170Z 270Z 350Z 450Z 800Z IN THE BEGINNING What began in the 19th century as an agricultural implement manufacturer has grown into a 21st century compact equipment powerhouse
More informationH Series Front Loader (European Specification)
H Series Front Loader (European Specification) 2 H Series Front Loader Introduction Made for each other Our new H Series front loaders are the perfect match for your John Deere tractor even if it s an
More informationQ26 Q36 Q38 Q39 Q46 Q48 Q49 Q56 Q58 Q66 Q68 Q76 Q78 Q88 Q98 Q21 Q31 Q33 Q41 Q51 Q61
Design that improves your profitability A complete range of professional front loaders and implements Q26 Q36 Q38 Q39 Q46 Q48 Q49 Q56 Q58 Q66 Q68 Q76 Q78 Q88 Q98 Q21 Q31 Q33 Q41 Q51 Q61 EN 2 A front loader
More informationFARMALL. SPRING INTO A NEW CASE IH 3000^ FARMALL. PROVEN SINCE REWARD DOLLARS ON FARMALL C, U & JX STRADDLE MODELS PARTS AND SERVICE
$ 3000^ UP TO IN EXCLUSIVE CASE IH PARTS AND SERVICE REWARD DOLLARS ON FARMALL C, U & JX STRADDLE MODELS SPRING INTO A NEW CASE IH FARMALL. FARMALL. PROVEN SINCE 1923. ADMIRED. REQUIRED. DESIRED. THERES
More information