A. Hardware for new doors. B. Keying of new hardware into existing hardware keying system.

Transcription

1 SECTION PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section SECTION INCLUDES A. Hardware for new doors. B. Keying of new hardware into existing hardware keying system RELATED SECTIONS A. Section Rough Carpentry, wood blocking for door stops. B. Section Steel Doors and Frames. C. Section Flush Wood Doors. D. Section Stile & Rail Wood Doors. E. Section Overhead Coiling Doors. F. Section Aluminum Entrances and Storefronts. G. Division 26 Electrical; power and control connections SUBMITTALS A. Completely itemized hardware schedule, coordinated with the schedule below, and the door schedule. Coordinate the final door hardware sets with doors, frames, and related work to ensure proper size, thickness, hand, function, and finish of door hardware. B. Catalog cuts for each item specified. C. Samples if required by the Architect. Include one representative piece of each item of hardware requested. Tag samples to show their intended use. Samples will be retained by the Architect until the project is nearly completed, at which time they may be incorporated into the work. D. Paper templates, approved hardware schedule and, when required, actual hardware shall be sent to frame and door manufacturers in sufficient time for those manufacturers to prepare for hardware and to incorporate hardware into their products if required. E. Wiring Diagrams: power, signal and control wiring QUALITY ASSURANCE A. Qualifications of Supplier: shall be a qualified member in good standing with Door and Hardware Institute (DHI) and certified as an Architectural Hardware Consultant (AHC) shall properly schedule and service hardware requirements, including delivery and installation of hardware ( )

2 B. Requirements of Regulatory Agencies: Comply with the following: 1. Exit Devices: Listed under "Panic Hardware" in the current edition of "UL" Accident and Burglary Protection Equipment List `or in a Supplement to that publication. 2. Fire-Rated Door Assemblies: Assemblies complying with NFPA 80 that are listed and labeled by a testing and inspecting agency acceptable to authorities having jurisdiction, for fire ratings indicated, based on testing according to NFPA Electrified Door Hardware: Listed and labeled as defined in NFPA 70, Article 100, by a testing agency acceptable to authorities having jurisdiction, and marked for intended use. 4. Commonwealth of Pennsylvania: Department of Health - National Fire Protection Association (NFPA) Americans with Disabilities Act (ADA) Accessibility Guidelines for Buildings and Facilities (ADAGG). 6. Door and Hardware Institute (DHI) Any hardware required by agencies above omitted from this section shall be furnished and installed PRODUCT DELIVERY, STORAGE AND HANDLING A. The installer shall use all means necessary to protect material of this Section before, during, and after installation, including protection of existing construction and the installed work of other trades. B. In the event of damage to this or other trades or existing construction, replace damaged material at no additional cost. C. Pack hardware in boxes. Plainly mark each box with the identification of the opening for which hardware is intended, including packing list showing each item enclosed, proper screws, bolts, accessories, and similar items in each box. D. Deliver all products to job site in manufacturer's unopened containers with labels intact. E. Check hardware on receipt at the project to insure that each set is complete and operative. F. Store hardware in a manner which will prevent damage and which will insure that no items are removed from any set before installation ( )

3 1.07 COORDINATION A. Templates: Distribute door hardware templates for doors, frames, and other work specified to be factory prepared for installing door hardware. Check Shop Drawings of other work to confirm that adequate provisions are made for locating and installing door hardware to comply with indicated requirements. B. Electrical System Roughing-in: Coordinate layout and installation of electrified door hardware with connections to power supplies, access control system, security system. C. Existing Openings: Where new hardware components are scheduled for application to existing construction or where modifications to existing door hardware are required, field verify existing conditions and coordinate installation of door hardware to suit opening conditions and to provide for proper operation WARRANTY A. Special Warranty: Manufacturer's standard form in which manufacturer agrees to repair or replace components of door hardware that fail in materials or workmanship within specified warranty period. 1. Failures include, but are not limited to, the following: a. Structural failures including excessive deflection, cracking, or breakage. b. Faulty operation of operators and door hardware. c. Deterioration of metals, metal finishes, and other materials beyond normal weathering and use. 2. Warranty Period: Three years from date of Substantial Completion, except as follows: PART 2 - PRODUCTS 2.01 REQUIREMENTS a. Exit Devices: Two years from date of Substantial Completion. b. Manual Closers: 10 years from date of Substantial Completion. A. Sizes, weights and quality specified are minimum acceptable. B. Should item of hardware not specified be required for completion of the work, furnish such items of types and quantities suitable for the service required and comparable to adjacent or similar hardware. C. Should it be determined that specified hardware for any location, ( )

4 because of detail or size of member to which the hardware is to be applied, is unsuitable, provide hardware of the proper type. Such hardware shall be similar in operation to types specified and not of lesser quality. D. Locks shall have keepers. Catches shall have strikes. Provide required escutcheons and plates. E. Screws: All exposed screws shall be security type FINISHES A. Finish Designations include the following: US Finish Description BHMA Finish Base Material 2C Zinc Plated BHMA-603 steel 26D Chromium Plated BHMA-652 steel Satin 26D Chromium Plated BHMA-626 brass/bronze Satin 32D Stainless Steel BHMA-630 stainless steel Satin B. Finish of hardware and accessories as selected by Architect from selections above. Exposed portions of door closers shall have a sprayed finish to match adjacent hardware. Locksets, exit devices, push plates, pull plates and kickplates shall have matching finishes. Aluminum threshold and weatherstripping shall match adjacent hardware MATERIALS/MANUFACTURERS A. Manufacturers: 1. Best Access System; Indianapolis, IND , 2. Glynn Johnson; Indianapolis, IND Hager Hinge; St. Louis MO LCN; Princton, ILL Lund Key Cabinets; Bath, OH McKinney Mfg. Co Scranton, PA , 7. National Guard Products; Memphis, TN Pemko Mfg. Co. a Division of ASSA ABLOY; Memphis, TN Rixon-Division of ASSA ABLOY; Franklin Park, ILL Rockwood Mfg. Co. Rockwood, PA Stanley Hardware; New Britain, CT ( )

5 12. Von Duprin; Indianapolis, IN Tellkee a Division of Tri Palm International; Columbus, OH B. Qualifications of Manufacturers: 1. Hardware numbers are taken from the catalogues of: a. Butts Hager b. Locksets Best Access Systems c. Exit Devices, Power Von Duprin Transfers d. Door Closers LCN, Inc. e. Door Trim Rockwood Mfg. Company f. Overhead Stops & Holders Glynn Johnson g. Thresholds, Gaskets Pemko Mfg. Company Automatic Door Bottoms, Drip Caps h. Flush Bolts, Dustproof Rockwood Mfg. Company Strikes, Door Stops, and Wall Bumpers i. Electric Strikes HES k. Key Cabinet Lund C. Other Manufacturers: 1. Hardware of the same types, weights, and functions approved by the architect and as manufactured by the following manufacturers may be bid: a. Butts Stanley, McKinney Mfg. Company b. Locksets NO Substitution c. Exit Devices, Power Supplies NO Substitution Power Transfer d. Door Closers NO Substitution e. Door Trim IVES; Hager Hinge f. Overhead Stops & Sargent & Company, Rixson- Holders Firemark Division, Zero g. Thresholds, Gaskets National Guard Products, Inc.; Reese Automatic Door Bottoms, Equipment, Inc.; Hager Hinge Drip Caps h. Flush Bolts, Dustproof Burns Mfg., Inc.; Hager Hinge Strikes, Door Stops, & Wall Bumpers i. Electric Strikes Von Duprin k. Key Cabinet Tellkee 2. Substitutions: Proposed substitutes shall be equal to the specified material with respect to size, quality, function, and finish. The supplier proposing to bid on substitute material shall request permission to do so from the architect not less than ten (10) ( )

6 days prior to bid date. If the substitution is allowed, it will be noted as an addendum. Deviation from this procedure will be cause for rejection of substitution request. D. Butts BHMA A156.1: 1. Furnish butts in types, weights, and sizes shown. 2. Furnish two (2) butts for each door 5 0 or less in height plus one (1) butt for each additional 2 6 in height or fraction thereof. 3. Furnish with non-removable pins (NRP) on all outswinging exterior doors. 4. Template hinge dimensions; BHMA A E. Door Bolts BHMA A156.16, Grade 1: 1. Flush bolts shall be equal to Rockwood Mfg. Company s No , furnished for top and bottom of inactive leaf, complete with dustproof strike No F. Door Closers BHMA 156.4, Grade 1: 1. All door closers shall be the product of one (1) manufacturer and will be equal to LCN 4041 Series. All closers shall be of full rack and pinion construction, with separate valves for adjusting closing and latching speeds and hydraulic backcheck, adjustable spring providing Closer Sizes 1 through 6 and removable non-ferrous covers. Extra duty arms where specified. Mounting applications to be: Standard or parallel with proper arm and brackets. Closer location subject to practicality and approval. G. Locksets BHMA A156.13, Grade 1: 1. Furnish Best 45h Series, 3-h Design heavy-duty type locksets and latchsets with 2-3/4 backset, 3/4 minimum throw latchbolt, and ANSI (1-1/4 X 4-7/8 ) strike, in the functions specified. H. Panic Hardware BHMA A156.3, Grade 1: 1. All exit devices shall be the product of one (1) manufacturer and must be listed under Panic Hardware in the Accident Equipment List of Underwriters Laboratories. In addition, where devices are required on labeled doors, devices will bear a UL label indicating Fire Exit Hardware. 2. Devices shall be "Von Duprin 98 Series in types and functions specified and with "9961/03" Series outside trim. No Substitutions ( )

7 I. Door Pulls and Push Plates: 1. Furnish pull plates and push plates as specified. 2. Pull plates shall have grips attached to the plates at the factory. J. Protections Plates BHMA A156.6: 1. Kickplates shall be 18 gauge (.050) by 8 high by 2 less than the nominal width of single doors and 1 less than the nominal width of double doors, and installed on the stop (push) side. Beveled top and two sides. K. Door Stops BHMA A156.16, Grade 1: 1. Furnish some type of stop for each door opening against a wall, fixture, or equipment, complete with fasteners as required by detail. Furnish wall bumpers equal to Rockwood s No. 409 wherever possible. General contractor to provide wood blocking in wall at each door stop location. 2. Furnish overhead stops and holders where specified: a. Door Silencers BHMA A146.16, Grade 1: 1. Furnish rubber door silencers for all hollow metal frames. Three (3) per single and two (2) per pair of doors, minimum diameter of ½ inch (13mm). L. Key Cabinet BHMA A156.5, Grade 1: 1. Lund type No Series metal cabinet with baked enamel finish with two (2) tag system with index pocket for storage. Furnish all keys to owner at completion of job in a key cabinet complete with all keys properly tagged and indexed ready for owner s use. Size as required, allow for 25% expansion. M. Thresholds, Gasketing, Automatic Door Bottoms and Drip Caps: 1. Thresholds BHMA A156.21: shall be the type specified under the hardware sets, furnished full length of opening with lead expansion shields for anchoring. All thresholds shall be set in full bed of mastic by contractor. Bevel raised thresholds with a slope of not more than 1:2. Provide thresholds not more than ½ inch (13mm) high. 2. Gasketing BHMA A156.22: shall be of the type specified under the hardware sets, furnished for both jambs and head. 3. Automatic Door Bottoms shall be of the type specified under the hardware sets ( )

8 4. Drip Caps: shall be of the type specified under the hardware sets O. Automatic Flush Bolts: 2.04 KEYING 1. Provide automatic flush bolts where specified, as manufactured by Rockwood. Acceptable Substitutions: Door Controls or Glynn Johnson. A. All locksets and cylinders shall be set to to the existing campus key system B. All keying requirements to be coordinated and completed at factory to protect the integrity of the system. Field keying will not be permitted and will be considered as just cause for rejection of supplier. C. Cylinder must be an integral part of lock as manufactured by specified lock supplier. Substitution of foreign made cylinders or components will not be allowed and also will be cause for rejection of supplier. D. Keys shall be furnished as follows: 1. Change keys (3) each. 2. Master keys (3) each set. 3. Grand Master Keys (3). 4. Construction Master Keys (3). 5. Core removal key (3). PART 3 - EXECUTION 3.01 INSTALLATION A. Examine areas in which the hardware is to be installed and report any areas which are unsatisfactory. Do not proceed with the work until such areas have been corrected. B. Hardware shall be installed hardware in a neat and workmanlike manner, in accordance with the manufacturer's specifications so that it operates smoothly, quietly, and properly. Inspect installed hardware and leave it in first class operating condition. C. Take care not to mark or damage adjacent work. Repair or replace damaged work to the Architect's satisfaction. D. Secure bumpers to walls with toggle bolts or expansion shields as required by wall or partition construction. E. Examine rough openings for electrical power system to verify actual locations of wiring connections before electrified hardware ( )

9 installation. F. Installation of steel doors and frames: DHI A115 series. G. Installation of wood doors: DHI A115-W series ADJUSTING A. Adjust and check each operating item of door hardware and each door to ensure proper operation or function of every unit. Replace units that cannot be adjusted to operate as intended. Adjust door control devices to compensate for final operation of heating and ventilating equipment and to comply with referenced accessibility requirements. 1. Strikes: Adjust horizontal and vertical alignment of keeper to properly engage lock bolt CLEANING AND PROTECTION A. Clean adjacent surfaces soiled by door hardware installation. B. Clean operating items as necessary to restore proper function and finish. C. Provide final protection and maintain conditions that ensure that door hardware is without damage or deterioration at time of Substantial Completion SCHEDULE A. The following schedule is included as a guide in establishing the quality, type, and function of hardware required for each opening and is not to be construed as all inclusive. Quantities listed under each hardware set for each opening, whether a pair or single door. HARDWARE SET 1 DOORS: G02-1, 114-1, 162-1, 168-1, 181-1, 193-1, NOTE: WEATHERSTRIPPING BY THE ALUMINUM DOOR SUPPLIER. 3 EA HINGE B X 4.5 (NRP) US26D 1 EA RIM EXIT DEVICE 98NL-OP US32D 1 EA RIM CYLINDER 1E72 US26D 1 EA PULL PLATE BF158 US32D 1 EA OH CONCEALED STOP 100S US26D 1 EA CLOSER A4041-DEL ALUM 1 EA EXIT SADDLE THR 2005AT X 36 A ( )

10 DOORS: HARDWARE SET 2 NOTE: WEATHERSTRIPPING BY THE ALUMINUM DOOR SUPPLIER. 3 EA HINGE B X 4.5 (NRP) US26D 1 EA RIM EXIT DEVICE 98NL-OP US32D 1 EA RIM CYLINDER 1E72 US26D 1 EA PULL PLATE BF158 US32D 1 EA OH CONCEALED STOP 100S US26D 1 EA CLOSER A4041-DEL ALUM 1 EA EXIT SADDLE THR 2005AT X 36 A DOORS: 129-1, HARDWAE SET 3 NOTE: WEATHERSTRIPPING BY THE ALUMINUM DOOR SUPPLIER. 6 EA HINGE B X 4.5 (NRP) US26D 1 EA VERT ROD DEVICE 9827EO US32D 1 EA VERT ROD DEVICE 9827NL-OP US26D 1 EA RIM CYLINDER 1E72 US26D 2 EA PULL PLATE BF158 US32D 2 EA OH CONCEALED STOP 100S US26D 2 EA CLOSER A4041-DEL ALUM 1 EA EXIT SADDLE THR 2005AT X 72 A DOORS: A14-2 HARDWARE SET 3A 3 EA HINGE B X 4.5 (NRP) US26D 1 EA RIM EXIT DEVICE 98EO US32D 1 EA CLOSER A4041-DEL ALUM 1 EA KICK PLATE 8 X 40 US32D 1 EA THERSHOLD 171A X 42" A 1 EA SILICON SEAL S88D20 1 EA BRUSH WEATHERST 3452CNB X 42" C ( )

11 HARDWARE SET 4 DOORS: 180A-2, 182A-1, 182A-4 (ADD#2) NOTE: WEATHERSTRIPPING BY THE ALUMINUM DOOR SUPPLIER. 3 EA HINGE B X 4.5 (NRP) US26D 1 EA STOREROOM LOCK 45H-7-D-3H US26D 1 EA OH CONCEALED HOLDER 100H US26D 1 EA CLOSER A4041-DEL ALUM 1 EA EXIT SADDLE THR 2005AT X 36 A DOORS: A09-1 HARDWARE SET 4A 3 EA HINGE B X 4.5 (NRP) US26D 1 EA STOREROOM LOCK 45H-7-D-3H US26D 1 EA O.H. HOLDER 90 H US26D 1 EA THRESHOLD 171A X 36" A 1 EA BRUSH WEATHERST 3452CNB X 36" C 1 EA SILICON SEAL S88D17 DOORS: 135A-1 HARDWARE SET 5 NOTE: WEATHERSTRIPPING BY THE ALUMINUM DOOR SUPPLIER. 6 EA HINGE B X 4.5 US26D 2 EA DUMMY PUSH PAD 350 US32D 2 EA PULL PLATE BF158 US32D 2 EA O.H. STOP 90 S US26D 2 EA CLOSER A A-DEL ALUM 1 EA EXIT SADDLE THR 2005AT X 72 A ( )

12 DOORS: 135A-2 HARDWARE SET 5A NOTE: CARD READER BY OTHERS. 6 EA HINGE B X 4.5 US26D 1 EA VERT ROD DEVICE 9827EO US32D 1 EA VERT ROD DEVICE EL9827NL-OP US32D 1 EA RIM CYLINDER 1E72 US26D 2 EA PULL PLATE BF158 US32D 2 EA O.H. STOP 90 S US26D 2 EA CLOSER A A-DEL ALUM 2 EA SILENCERS 608 GRAY 1 EA POWER SUPPLY PS873 1 EA POWER TRANSFER EPT10 SP28 HARDWARE SET 6 DOORS: 182A-1, 182A-2, 182A-3, 182A-4 (ADD#2) NOTE: DOOR, FRAME AND HARDWARE PART OF GREENHOUSE SYSTEM. FURNISH CYLINDERS AS REQUIRED. HARDWARE SET 7 DOORS: G11-1, 100-1, 105-1, 161-1, 167-1, 175-1, 183-1, 200-1, 209-1, 264-1, 272-1, 275-1, EA HINGE B X 4.5 US26D 1 EA RIM EXIT DEVICE 98L-BE-F-996L/03 US32D 1 EA CLOSER A4041-DEL ALUM DOORS: G03-1 HARDWARE SET 8 3 EA HINGE B X 4.5 US26D 1 EA RIM EXIT DEVICE 98L-BE-F-996L/03 US32D 1 EA CLOSER A4041-DEL ALUM ( )

13 DOORS: 106-1, 107-1, NOTE: CARD READER BY OTHERS. HARDWARE SET 9 3 EA HINGE B X 4.5 US26D 1 EA STOREROOM LOCK 45H-7-D-3H-LESS/STRIKE US26D 1 EA ELECTRIC STRIKE 1006-KM US32D 1 EA CLOSER A4041-DEL ALUM 1 EA KICK PLATE 8 X 40 US32D 1 EA SMART PAC II 2005 HARDWARE SET 10 DOORS: 153-1, NOTE: CARD READER BY OTHERS. 1 EA STOREROOM LOCK 45H-7-D-3H-LESS/STRIKE US26D 1 EA ELECTRIC STRIKE 1006-KM US32D 1 EA CLOSER RA4041-DEL ALUM 1 EA SMART PAC II 2005 HARDWARE SET 11 DOORS: 177-1, 240-1, 242-1, 245-1, 246-1, 266-1, 269-1, 278-2, NOTE: CARD READER BY OTHERS. 3 EA HINGE BB X 4.5 US26D 1 EA STOREROOM LOCK 45H-7-D-3H-LESS/STRIKE US26D 1 EA ELECTRIC STRIKE 1006-KM US32D 1 EA CLOSER PA4041-DEL ALUM 1 EA KICK PLATE 8 X 40 US32D 1 EA SMART PAC II ( )

14 DOORS: 176-1, NOTE: PROP ALARM BY OTHERS. HARDWARE SET 11A 3 EA HINGE BB X 4.5 US26D 1 EA STOREROOM LOCK 45H-7-D-3H US26D 1 EA CLOSER PA4041-DEL ALUM DOORS: NOTE: PROP ALARM BY OTHERS. HARDWARE SET 11B 3 EA HINGE BB X 4.5 US26D 1 EA STOREROOM LOCK 45H-7-D-3H US26D 1 EA CLOSER RA4041-DEL ALUM DOORS: NOTE: CARD READER BY OTHERS. HARDWARE SET 12 1 EA STOREROOM LOCK 45H-7-D-3H-LESS/STRIKE US26D 1 EA ELECTRIC STRIKE 1006-KM US32D 1 EA CLOSER PA4041-DEL ALUM 1 EA SMART PAC II ( )

15 HARDWARE SET 13 DOORS: 202-1, EA STOREROOM LOCK 45H-7-D-3H-LESS/STRIKE US26D 1 EA ELECTRIC STRIKE 1006-KM US32D 1 EA CLOSER RA4041-DEL ALUM 1 EA SMART PAC II 2005 DOORS: HARDWARE SET 14 NOTE: CARD READER BY OTHERS. 3 EA HINGE BB X 4.5 US26D 1 EA STOREROOM LOCK 45H-7-D-3H-LESS/STRIKE US26D 1 EA ELECTRIC STRIKE 1006-KM US32D 1 EA CLOSER RA4041-DEL ALUM 1 EA KICK PLATE 8 X 40 US32D 1 EA SILENCERS 608 GRAY 1 EA SMART PAC II 2005 HARDWARE SET 15 DOORS: EA HINGE BB X 4.5 US26D 1 EA STOREROOM LOCK 45H-7-D-3H-LESS/STRIKE US26D 1 EA ELECTRIC STRIKE 1006-KM US32D 1 EA CLOSER PA A-DEL ALUM 1 EA KICK PLATE 8 X 40 US32D 1 EA SMART PAC II ( )

16 DOORS: G14-1, G14-2 HARDWARE SET 16 6 EA HINGE BB X 4.5 US26D 1 EA VERT ROD DEVICE 9827EO-F US32D 1 EA VERT ROD DEVICE 9827L-NL-F-996L/03 US32D 1 EA RIM CYLINDER 1E72 US26D 2 EA CLOSER PA4041-DEL ALUM 2 EA KICK PLATE 8 X 35 US32D 2 EA DOOR STOP 406 US32D 2 EA SILENCERS 608 GRAY DOORS: 131A-1 HARDWARE SET 17 6 EA HINGE BB X 4.5 US26D 2 EA VERT ROD DEVICE F-996L/03 US32D 2 EA RIM CYLINDER 1E72 US26D 2 EA O.H. STOP 90 S US26D 2 EA CLOSER PA A-DEL ALUM 2 EA KICK PLATE 8 X 35 US32D 2 EA SILENCERS 608 GRAY HARDWARE SET 17A DOORS: 136A-1, 147-1, EA HINGE BB X 4.5 US26D 1 EA VERT ROD DEVICE 9827EO US32D 1 EA VERT ROD EXIT 9827L-996L/03 US32D 1 EA RIM CYLINDER 1E72 US26D 1 EA O.H. HOLDER 90 H US26D 1 EA CLOSER PA A-DEL ALUM 1 EA KICK PLATE 8 X 35 US32D 2 EA SILENCERS 608 GRAY ( )

17 DOORS: HARDWARE SET 17B 6 EA HINGE BB X 4.5 US26D 2 EA VERT ROD DEVICE 9827L-BE-F-996L/03 US32D 2 EA O.H. STOP 90 S US26D 2 EA CLOSER PA A-DEL ALUM 2 EA KICK PLATE 8 X 35 US32D 2 EA SILENCERS 608 GRAY HARDWARE SET 18 DOORS: EA RIM EXIT DEVICE 98L-F-996L/03 US32D 1 EA RIM CYLINDER 1E72 US26D 1 EA CLOSER PA4041-DEL ALUM DOORS: 131B-3 HARDWARE SET 19 1 EA RIM EXIT DEVICE 98L-F-996L/03 US32D 1 EA RIM CYLINDER 1E72 US26D 1 EA CLOSER PA A-DEL ALUM DOORS: G21-1 HARDWARE SET 19A 1 EA RIM EXIT DEVICE 98L-NL-F-996L/03 US32D 1 EA RIM CYLINDER 1E72 US26D 1 EA CLOSER PA SC ALUM ( )

18 DOORS: 184-1, HARDWARE SET 20 3 EA HINGE BB X 4.5 US26D 1 EA IND CLASSROOM 45H-7-IND-3H US26D 1 EA CLOSER PA4041-DEL ALUM 1 EA KICK PLATE 8 X 40 US32D DOORS: HARDWARE SET 20A 3 EA HINGE BB X 4.5 US26D 1 EA IND CLASSROOM 45H-7-IND-3H US26D 1 EA CLOSER PA A-DEL ALUM 1 EA KICK PLATE 8 X 40 US32D 1 EA SILICON SEAL S88D20 1 EA AUTOMATIC DOOR 4131CRL X 42" C DOORS: HARDWARE SET 21 NOTE:PROP ALARM BY OTHERS. 6 EA HINGE BB X 4.5 US26D 1 EA D.P. STRIKE 570 US26D 2 EA BOLTS & LATCHES D 1 EA STOREROOM LOCK 45H-7-D-3H US26D 1 EA CLOSER PA4041-DEL ALUM 1 EA KICK PLATE 8 X 35 US32D 1 EA KICK PATE 8 X 23 US32D 2 EA DOOR STOP 406 US32D 2 EA SILENCERS 608 GRAY ( )

19 DOORS: G00-1, G16-2 HARDWARE SET 21A 6 EA HINGE BB X 4.5 US26D 2 EA FLUSH BOLT " US26D 1 EA D.P. STRIKE 570 US26D 1 EA STOREROOM LOCK 45H-7-D-3H US26D 1 EA CLOSER PA SC ALUM 2 EA SILENCERS 608 GRAY HARDWARE SET 22 DOORS: EA HINGE BB X 4.5 US26D 1 EA D.P. STRIKE 570 US26D 2 EA BOLTS & LATCHES D 1 EA IND CLASSROOM 45H-7-IND-3H US26D 1 EA CLOSER PA4041-DEL ALUM 1 EA KICK PATE 8 X 23 US32D 2 EA DOOR STOP 406 US32D 2 EA SILENCERS 608 GRAY HARDWARE SET 23 DOORS: 153A-1, 153B-1, 182D-1 1 EA STOREROOM LOCK 45H-7-D-3H US26D 1 EA CLOSER RA4041-DEL ALUM ( )

20 DOORS: HARDWARE SET 24 1 EA OFFICE LOCK 45H-7-A-3H US26D 1 EA CLOSER PA A-DEL ALUM HARDWARE SET 25 DOORS: 140-1, 158-1, 185-1, 235-1, EA IND CLASSROOM 45H-7-IND-3H US26D 1 EA CLOSER RA4041-DEL ALUM DOORS: 131C-1, HARDWARE SET 25A 1 EA IND CLASSROOM 45H-7-IND-3H US26D 1 EA CLOSER PA SC ALUM DOORS: HARDWARE SET 25B 1 EA IND CLASSROOM 45H-7-IND-3H US26D 1 EA CLOSER RA4041-DEL ALUM ( )

21 HARDWARE SET 26 DOORS: 241-1, 301-1, 304-1, EA STOREROOM LOCK 45H-7-D-3H US26D 1 EA CLOSER PA SC ALUM DOORS: G15-1 HARDWARE SET 26A 3 EA HINGE BB X 4.5 US26D 1 EA STOREROOM LOCK 45H-7-D-3H US26D 1 EA CLOSER PA SC ALUM DOORS: HARDWARE SET 27 1 EA PASSAGE LOCK 45H-0-N-3H US26D 1 EA CLOSER PA A-DEL ALUM 1 EA KICK PLATE 8 X 35 US32D DOORS: HARDWARE SET 28 1 EA PASSAGE LOCK 45H-0-N-3H US26D 1 EA CLOSER PA4041-DEL ALUM ( )

22 DOORS: HARDWARE SET 29 1 EA COMM LOCK 45H-7-G-3H US26D 1 EA CLOSER PA A-DEL ALUM HARDWARE SET 30 DOORS: G05-2, G19-2, G EA HINGE BB X 4.5 US26D 2 EA FLUSH BOLT " US26D 1 EA DEADLOCK 48H-7-L-48HS1 US26D 2 EA OH CONCEALED HOLDER 100H US26D 1 EA THRESHOLD 171A X 64" A 2 EA BRUSH WEATHERST 3452CNB X 32" C 1 EA SILICON SEAL S88D20 2 EA FLUSH PULL BF97L US32D 1 EA OVERLAPPING AST 357SP84 SP DOORS: G16-1 HARDWARE SET 31 6 EA HINGE BB X 4.5 US26D 2 EA FLUSH BOLT " US26D 1 EA DEADLOCK 48H-7-L-48HS1 US26D 2 EA OH CONCEALED HOLDER 100H US26D 1 EA THRESHOLD 171A X 72" A 2 EA BRUSH WEATHERST 3452CNB X 36" C 1 EA SILICON SEAL S88D20 2 EA FLUSH PULL BF97L US32D 1 EA OVERLAPPING AST 357SP84 SP ( )

23 HARDWARE SET 32 DOORS: G01-1, G04-1, G04-2, 163-1, 164-2, 165-1, 166-1, 203-1, 238-1, 239-1, 284-1, EA IND CLASSROOM 45H-7-IND-3H US26D DOORS: 277-1, HARDWARE SET 32A 1 EA IND CLASSROOM 45H-7-IND-3H US26D 1 EA O.H. HOLDER 90 H US26D HARDWARE SET 33 DOORS: 101-1, 128-3, 137-1, 159-1, 164-1, 213-1, 255-2, 293-2, EA IND CLASSROOM 45H-7-IND-3H US26D HARDWARE SET 34 DOORS: 102-1, 128-2, 155-1, 230-1, 270-1, EA HINGE BB X 4.5 US26D 1 EA IND CLASSROOM 45H-7-IND-3H US26D ( )

24 DOORS: HARDWARE SET 34A 3 EA HINGE BB X 4.5 US26D 1 EA IND CLASSROOM 45H-7-IND-3H US26D 1 EA O.H. HOLDER 90 H US26D HARDWARE SET 35 DOORS: 109-1, 111-1, 112-1, 113-1, 144-1, 145-1, 151-1, 152-1, 186-1, 187-1, 190-1, 212-1, 218-1, 220-1, 259-1, 261-1, 263-1, 279-1, 287-1, EA OFFICE LOCK 45H-7-A-3H US26D HARDWARE SET 36 DOORS: 110-1, 138-1, 138-3, 189-1, 191-1, 192-1, 204-1, 205-1, 206-1, 207-1, 210-1, 211-1, 217-1, 219-1, 260-1, 262-1, 285-1, 288-1, 289-1, 1 EA OFFICE LOCK 45H-7-A-3H US26D DOORS: G20-1 HARDWARE SET 37 1 EA STOREROOM LOCK 45H-7-D-3H US26D 1 EA CLOSER PA4041-DEL ALUM ( )

25 DOORS: 229A-1 HARDWARE SET 38 3 EA HINGE BB X 4.5 US26D 1 EA STOREROOM LOCK 45H-7-D-3H US26D 1 EA CLOSER PA4041-DEL ALUM DOORS: HARDWARE SET 38A 1 EA STOREROOM LOCK 45H-7-D-3H US26D 1 EA CLOSER RA4041-DEL ALUM HARDWARE SET 39 DOORS: G10-1, G19-1, G24-1, 103-1, 131D-1, 131E-1, 143A-1, 146-1, 180-1, 180A-1, 216-1, 233A-1, 234-1, 247-1, 248-1, 256-1, EA STOREROOM LOCK 45H-7-D-3H US26D 1 EA O.H. HOLDER 90 H US26D HARDWARE SET 39A DOORS: A01-1, A02-1, A03-1, A05-1, A06-1, A07-1, A10-1, A11-1, A12-1, A EA HINGE BB X 4.5 US26D 1 EA CLASSROOM LOCK 45H-7--R-3H US26D 1 EA O.H. HOLDER 90 H US26D ( )

26 HARDWARE SET 40 DOORS: G05-1, G06-1, G22-1, G25-1, EA STOREROOM LOCK 45H-7-D-3H US26D DOORS: A00-1 HARDWARE SET 40A 3 EA HINGE BB X 4.5 US26D 1 EA STOREROOM LOCK 45H-7-D-3H US26D DOORS: A08-1 HARDWARE SET 40B 3 EA HINGE BB X 4.5 US26D 1 EA STOREROOM LOCK 45H-7-D-3H US26D 1 EA O.H. HOLDER 90 H US26D HARDWARE SET 41 DOORS: 101-2, 101-3, 101A-1, 101B-1, 128A-1, 269-2, EA PASSAGE LOCK 45H-0-N-3H US26D HARDWARE SET 41A DOORS: A04A-1,103-2, 138-2, 139-2, 140-2, 140-3, 141-2, 155-2, 177-2, 185-2, 230-2, 256-2, 284-3, EA PASSAGE LOCK 45H-0-N-3H US26D ( )

27 DOORS: 101C-1, 101D-1 HARDWARE SET 42 1 EA PASSAGE LOCK 45H-0-N-3H US26D 1 EA SILICON SEAL S88D17 1 EA AUTOMATIC DOOR 4131CRL X 36" C DOORS: HARDWARE SET 42A 1 EA PASSAGE LOCK 45H-0-N-3H US26D 1 EA SILICON SEAL S88D17 1 EA AUTOMATIC DOOR 4131CRL X 36" C DOORS: 131B-1, HARDWARE SET 43 1 EA CLASSROOM LOCK 45H-7--R-3H US26D 1 EA CLOSER PA A-DEL ALUM DOORS: 131B-2 HARDWARE SET 44 1 EA CLASSROOM LOCK 45H-7--R-3H US26D 1 EA CLOSER RA4041-DEL ALUM ( )

28 DOORS: HARDWARE SET 45 1 EA CLASSROOM LOCK 45H-7--R-3H US26D 1 EA O.H. HOLDER 90 H US26D DOORS: 242-2, 242-3, HARDWARE SET 46 1 EA COMM LOCK 45H-7-G-3H US26D 1 EA O.H. HOLDER 90 H US26D DOORS: 293-1, HARDWARE SET 47 6 EA HINGE BB X 4.5 US26D 2 EA FLUSH BOLT " US26D 1 EA D.P. STRIKE 570 US26D 1 EA IND CLASSROOM 45H-7-IND-3H US26D 2 EA DOOR STOP 406 US32D 2 EA SILENCERS 608 GRAY DOORS: 128-1, HARDWARE SET 48 6 EA HINGE BB X 4.5 US26D 2 EA FLUSH BOLT " US26D 1 EA D.P. STRIKE 570 US26D 1 EA IND CLASSROOM 45H-7-IND-3H US26D 2 EA O.H. HOLDER 90 H US26D 2 EA SILENCERS 608 GRAY ( )

29 DOORS: HARDWARE SET 49 3 EA HINGE BB X 4.5 US26D 1 EA DEADLOCK 48H-7-R-48HS2 US26D 1 EA PULL PLATE BF110 US32D 1 EA PUSH PLATE 70C US32D 1 EA CLOSER PA A-DEL ALUM 1 EA KICK PLATE 8 X 40 US32D DOORS: HARDWARE SET 50 3 EA HINGE BB X 4.5 US26D 1 EA DEADLOCK 48H-7-R-48HS2 US26D 1 EA PULL PLATE BF110 US32D 1 EA PULL PLATE BF158 US32D 1 EA CLOSER RA4041-DEL ALUM 1 EA KICK PLATE 8 X 40 US32D HARDWARE SET 51 DOORS: 130A-1, 236A-1, 249-1, EA HINGE BB X 4.5 US26D 2 EA FLUSH BOLT " US26D 1 EA D.P. STRIKE 570 US26D 1 EA DEADLOCK 48H-7-L-48HS1 US26D 2 EA O.H. HOLDER 90 H US26D 2 EA FLUSH PULL BF97L US32D 2 EA SILENCERS 608 GRAY ( )

30 HARDWARE SET 52 DOORS: 126-1, 127-1, 133-1, 227-1, EA DEADLOCK 48H-7-R-48HS2 US26D 1 EA PULL PLATE BF110 US32D 1 EA PUSH PLATE 70C US32D 1 EA CLOSER RA4041-DEL ALUM HARDWARE SET 53 DOORS: 134-1, 142-1, 143-1, 231-1, EA DEADLOCK 48H-7-R-48HS2 US26D 1 EA PULL PLATE BF110 US32D 1 EA PUSH PLATE 70C US32D 1 EA CLOSER RA4041-DEL ALUM HARDWARE SET 54 DOORS: G08-1, G09-1, 243-1, EA PRIVACY LOCK 45H-0-L-3H US26D ( )

31 HARDWARE SET 55 DOORS: A05B-1, A EA HINGE BB X 4.5 US26D 1 EA PULL PLATE BF110 US32D 1 EA PUSH PLATE 70C US32D 1 EA CLOSER PA4041-DEL ALUM 1 EA KICK PLATE 8 X 40 US32D DOORS: G12-1 HARDWARE SET 56 1 EA DUMMY PUSH PAD 350 US32D 1 EA PULL PLATE BF158 US32D 1 EA CLOSER PA A-DEL ALUM HARDWARE SET 57 DOORS: 115-1, 169-1, 169-2, 194-1, EA HINGE BB X 4.5 US26D 1 EA DUMMY PUSH PAD 350 US32D 1 EA PULL PLATE BF158 US32D 1 EA CLOSER PA A-DEL ALUM ( )

32 DOORS: 131-1, 132-2, HARDWARE SET 58 6 EA HINGE BB X 4.5 US26D 2 EA DUMMY PUSH PAD 350 US32D 2 EA PULL PLATE BF158 US32D 2 EA O.H. STOP 90 S US26D 2 EA CLOSER PA A-DEL ALUM 2 EA KICK PLATE 8 X 35 US32D 2 EA SILENCERS 608 GRAY DOORS: HARDWARE SET 59 NOTE: ALL HARDWARE COMPLETE BY THE O. H. COILING DOOR SUPPLIER. FURNISH CYLINDERS AS REQUIRED. DOORS: HARDWARE SET 60 NOTE: ALL HARDWARE COMPLETE BY THE ALUMINUM SLIDING DOOR SUPPLIER. FURNISH CYLINDERS AS REQUIRED. DOORS: HARDWARE SET 61 NOTE: DOOR, FRAME AND HARDWARE COMPLETE BY THE COLD ROOM ENCLOSURE SUPPLIER. DOORS: A16-1 HARDWARE SET 62 NOTE: EXISTING DOOR, FRAME AND HARDWARE TO REMAIN. END OF SECTION ( )