TIMING BELT (4A FE) COMPONENTS

Size: px
Start display at page:

Download "TIMING BELT (4A FE) COMPONENTS"

Transcription

1 EM30 Timing Belt (4AFE) TIMING BELT (4AFE) COMPONENTS REMOVAL OF TIMING BELT 1. REMOVE RH FRONT WHEEL 2. REMOVE RH ENGINE UNDER COVER 3. REMOVE WASHER TANK 4. LOOSEN WATER PUMP PULLEY BOLTS AND REMOVE ALTERNATOR DRIVE BELT (a) Stretch the belt tight and loosen the water pump pulley bolts. (b) Loosen the pivot nut and adjusting bolt, and remove drive belt.

2 Timing Belt (4AFE) EM31 5. (with A/C) REMOVE A/C COMPRESSOR DRIVE BELT (a) Loosen the idler pulley mount bolt A. (b) Loosen the adjusting bolt B and remove the drive belt. 6. (w/ PS) REMOVE PS PUMP DRIVE BELT (a) Loosen the pivot and lock bolts. (b) Swing PS pump toward the engine and remove the drive belt. 7. DISCONNECT ENGINE WIRE FROM NO.3 TIMING BELT COVER (a) Disconnect the following connectors and wire: Alternator connector Alternator wire Oil pressure switch connector (with A/C) Compressor connector (b) Remove the bolt. (c) Disconnect the wire clamp from the wire bracket, and disconnect the engine wire from the timing belt cover. 8. REMOVE SPARK PLUG (a) Disconnect the hightension cord from spark plug. (b) Using a plug wrench (16 mm), remove the spark plugs. 9. REMOVE CYLINDER HEAD COVER (a) Disconnect the PCV hoses from the cylinder head cover. (b) Remove the three cap nuts, grommet and cylinder head cover with the gasket.

3 EM32 Timing Belt (4AFE) 10. SET NO.1 CYLINDER AT TDC/COMPRESSION (a) Turn the crankshaft pulley and align its groove with the No.1 timing belt cover. (b) Check that the valve lifters on the No. 1 cylinder are loose. If not, turn the crankshaft pulley one complete revolution (360 ). 11. REMOVE RH ENGINE MOUNTING INSULATOR (a) Set the jack to the engine. HINT: Place a wooden block between the jack and engine. (b) Remove the three bolts and mounting stay. (c) Remove the bolt, two nuts, through bolt and RH mounting. 12. REMOVE WATER PUMP PULLEY 13. REMOVE CRANKSHAFT PULLEY (a) Using SST to hold the crankshaft pulley, remove the pulley bolt. SST and

4 Timing Belt (4AFE) EM33 (b) Using SST, remove the pulley. SST REMOVE TIMING BELT COVERS Remove the nine bolts, engine wire bracket and timing belt covers. 15. REMOVE TIMING BELT GUIDE 16. REMOVE TIMING BELT AND IDLER PULLEY HINT: If reusing the timing belt, draw a direction arrow on the belt (in direction of engine revolution), and place matchmarks on the pulleys and belt as shown in the illustration. (a) Remove the bolt, idler pulley and tension spring. (b) Remove the timing belt. 17. REMOVE CRANKSHAFT TIMING PULLEY 18. REMOVE CAMSHAFT TIMING PULLEY Hold the hexagonal head wrench portion of the camshaft with a wrench, and remove the bolt and timing pulley. NOTICE: Be careful not to damage the cylinder head with the wrench.

5 EM34 Timing Belt (4AFE) INSPECTION OF TIMING BELT COMPONENTS 1. INSPECT TIMING BELT NOTICE: Do not bend, twist or turn the timing belt inside out. Do not allow the timing belt to come into contact with oil, water or steam. Do not utilize timing belt tension when installing or removing the mount bolt of the camshaft timing pulley. If there are any defects as shown in the illustrations, check the following points: (a) Premature splitting Check for proper installation. Check the timing cover gasket for damage and proper installation. (b) If the belt teeth are cracked or damaged, check to see if either camshaft, water pump is locked. (c) If there is noticeable wear or cracks on the belt face, check to see if there are nicks on the side of the idler pulley lock. (d) If there is wear or damage on only one side of the belt, check the belt guide and the alignment of each pulley.

6 Timing Belt (4AFE) EM35 (e) If there is noticeable wear on the belt teeth, check the timing cover for damage and check for correct gasket installation and for foreign material on the pulley teeth. If necessary, replace the timing belt. 2. INSPECT IDLER PULLEY Check the turning smoothness of the idler pulley. If necessary, replace the idler pulley. 3. INSPECT TENSION SPRING (a) Measure the free length of the tension spring. Free length: 38.4 mm (1.512 in.) If the free length is not as specified, replace the tension spring. (b) Measure the tension of the tension spring at the specified installed length. Installed tension: kg ( b,3539Nm) at 50.2 mm (1.976 in.) If the tension is not as specified, replace the tension spring.

7 EM36 Timing Belt (4AFE) INSTALLATION OF TIMING BELT (See page EM30) 1. INSTALL CAMSHAFT TIMING PULLEY (a) Align the camshaft knock pin with the knock pin groove of the pulley, and slide on the pulley. (b) Temporarily install the timing pulley bolt. (c) Hold the hexagonal wrench head portion of the camshaft with a wrench, and tighten the timing pulley bolt. Torque: 600 kgcm (43 ftib, 59 Nm) (d) Turn the hexagonal wrench head portion of the camshaft, and align the hole of the camshaft timing pulley with the timing mark of the bearing cap. 2. INSTALL CRANKSHAFT TIMING PULLEY (a) Align the pulley set key with the key groove of the pulley. (b) Slide on the timing pulley, facing the flange side inward. (c) Using the crankshaft pulley bolt, turn the crankshaft and align the timing marks of the crankshaft timing pulley and oil pump body. 3. TEMPORARILY INSTALL IDLER PULLEY AND TENSION SPRING (a) Install the idler pulley with the bolt. Do not tighten the bolt yet. (b) Install the tension spring. (c) Push the pulley toward the left as far as it will go and tighten the bolt. 4. INSTALL TIMING BELT NOTICE: The engine should be cold. HINT: If reusing the timing belt, align the points marked during removal, and install the belt with the arrow pointing in the direction of engine revolution.

8 Timing Belt (4AFE) EM37 5. CHECK VALVE TIMING AND TIMING BELT TENSION (a) Loosen the timing belt idler pulley mount bolt. (b) Temporarily install the crank pulley bolt and turn the crankshaft two revolutions from TDC to TDC. HINT: Always turn the crankshaft clockwise. (c) Check the valve timing. Ensure that each pulley aligns with the marks as shown in the illustration. (d) Tighten the timing belt idler pulley mount bolt. Torque: 375 kgcm (27 ftib, 37 Nm) (e) Remove the temporarily installed crank pulley bolt. (Reference) (a) Measure the timing belt deflection as shown in the illustration. Timing belt deflection: 5 6 mm ( in.) at 2 kg (4.4 Ib, 20 N )

9 EM38 Timing Belt (4AFE) (b) If the measured value is not within standard, readjust with the idler pulley. 6. INSTALL TIMING BELT GUIDE Install the guide, facing the cup side outward. 7. INSTALL TIMING BELT COVERS (a) Install the timing belt cover with the three bolts. (b) Install the No.2, No.3 timing belt covers and engine wire bracket with the six bolts. Torque: 75 kgcm (^5 inib, 7.4 Nm) 8. INSTALL CRANKSHAFT PULLEY (a) Align the pulley set key with the key groove of the pulley, slide on the pulley. (b) Temporarily install the pulley bolt. (c) Using SST, install the pulley bolt. SST and Torque: 1,200 kgcm (87 ftib, 118 Nm) 9. TEMPORARILY INSTALL WATER PUMP PULLEY 10. INSTALL RH ENGINE MOUNTING INSULATOR (a) Install the RH mounting insulator to the engine mounting bracket with the two nuts and bolt. Align the RH mounting insulator with the body bracket and install the mounting through bolt and nut. Torque: Bolt 650 kgcm (47 ftib, 64 Nm) Nut 530 kgcm (38 ftib, 52 Nm) Through bolt 890 kgcm (64 ftib, 87 Nm)

10 Timing Belt (4AFE) EM39 (b) Install the RH mounting stay with the three bolts. Torque: 430 kgcm (31 ftib, 42 Nm) (c) Remove the jack. 11. INSTALL CYLINDER HEAD COVER (a) Apply seal packing as shown in the illustration. Seal packing: Part No or equivalent HINT: Clean the indicated portions by removing the original sealant before recoating. (b) Install the cylinder head cover with the three grommet and bolts. (c) Install the PCV hoses. 12. INSTALL SPARK PLUG (a) Using a plug wrench (16 mm), install the spark plugs. Torque: 180 kgcm (13 ftib, 18 Nm) (b) Connect the hightension cords to spark plugs. 13. CONNECT ENGINE WIRE TO NO.3 TIMING BELT COVER (a) Connect the engine wire to the timing belt cover, and connect the wire clamp to the wire bracket. (b) Install the bolt. (c) Connect the following connectors and wire: Alternator connector Alternator wire Oil pressure switch connector (with A/C) Compressor connector

11 EM40 Timing Belt (4AFE) 14. TEMPORARILY INSTALL WATER PUMP PULLEY Install the water pump pulley and partially tighten the four bolts. 15. (wi PS) INSTALL PS PUMP DRIVE BELT 16. (with A/C) INSTALL A/C COMPRESSOR DRIVE BELT 17. INSTALL ALTERNATOR DRIVE BELT 18. ADJUST DRIVE BELTS Using a belt tension gauge, check the drive belt tension. Belt tension gauge: Nippondenso BTG20 ( ) or Borroughs No. BT3373F Drive belt tension: Alternator New belt 160 ± 20 Ib Used belt 130 ± 20 Ib PS New belt 125 ± 25 Ib Used belt 80 ± 20 Ib A/C New belt 160 ± 20 Ib Used belt 100 ± 20 Ib If necessary, adjust the drive belt tension. HINT: New belt refers to a belt which has been used less than 5 minutes on a running engine. Used belt refers to a belt which has been used on a running engine for 5 minutes or more. After installing the drive belt, check that it fits properly in the ribbed grooves. Check with your hand to confirm that the belt has not slipped out of the groove at the bottom of the crank pulley. After installing a new belt, run the engine for about 5 minutes and then recheck the tension. 19. TIGHTEN WATER PUMP PULLEY BOLTS 20. INSTALL WASHER TANK 21. INSTALL RH ENGINE UNDER COVER 22. INSTALL RH FRONT WHEEL

TIMING BELT (3S FE) COMPONENTS

TIMING BELT (3S FE) COMPONENTS Timing Belt (3SFE) TIMING BELT (3SFE) COMPONENTS EM23 REMOVAL OF TIMING BELT 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY 2. REMOVE RH FRONT WHEEL 3. REMOVE ENGINE RH UNDER COVER 4. REMOVE CRUISE

More information

TIMING BELT (5S FE) COMPONENTS

TIMING BELT (5S FE) COMPONENTS ENGINE MECHANICAL Timing Belt (5SFE) EM67 TIMING BELT (5SFE) COMPONENTS REMOVAL OF TIMING BELT 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started after approx. 20 seconds

More information

Timing Belt: Service and Repair Timing Belt Replace. Timing Belt Removal

Timing Belt: Service and Repair Timing Belt Replace. Timing Belt Removal 1998 Toyota Corolla DX Sedan 4-Door L4-1762cc 1.8L DOHC MFI Page 1 Timing Belt: Service and Repair Timing Belt Replace Timing Belt Removal SPECIAL SERVICE TOOL (SST) REQUIRED ^ 09213-70010 Crankshaft Pulley

More information

Toyota Camry CE Sedan L4-2.2L DOHC (5S-FE) MFI Timing Belt: Service and Repair

Toyota Camry CE Sedan L4-2.2L DOHC (5S-FE) MFI Timing Belt: Service and Repair Toyota Camry CE Sedan L4-2.2L DOHC (5S-FE) MFI 2001 Timing Belt: Service and Repair REMOVAL 1. REMOVE GENERATOR 2. REMOVE RH FRONT WHEEL 3. REMOVE RH FRONT FENDER APRON SEAL 4. REMOVE PS PUMP DRIVE BELT

More information

TIMING BELT COMPONENTS EM 15

TIMING BELT COMPONENTS EM 15 ENGINE MECHANICAL COMPONENTS EM15 EM16 ENGINE MECHANICAL COMPONENTS (Cont d) ENGINE MECHANICAL EM17 REMOVAL OF (See pages EM15 and 16) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work

More information

2000 Toyota Truck Tundra. Timing Belt: Service and Repair

2000 Toyota Truck Tundra. Timing Belt: Service and Repair Timing Belt: Service and Repair REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE RADIATOR ASSEMBLY 4. REMOVE THROTTLE BODY COVER 5. REMOVE INTAKE AIR CONNECTOR ASSEMBLY 6. REMOVE

More information

EG-34 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION

EG-34 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG34 TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG35 TIMING BELT REMOVAL (See Components for Removal and Installation) 1. DISCONNECT NEGATIVE TERMINAL CABLE FROM BATTERY CAUTION: Work must be

More information

8/14/2016 8:12 PM. Bolt: Part No for Type B

8/14/2016 8:12 PM. Bolt: Part No for Type B 1 of 21 2 of 21 REMOVAL 1. DISCONNECT PS RESERVOIR AND REMOVE RESERVOIR BRACKET 2. DISCONNECT WIRE HARNESS BRACKET FOR DLC1 3. REMOVE GENERATOR 4. REMOVE GENERATOR BRACKET 5. w/ ABS: REMOVE NO.3 ABS ACTUATOR

More information

2/17/2017 Timing Belt Service and Repair, Removal and Replacement

2/17/2017 Timing Belt Service and Repair, Removal and Replacement http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com 1/22 http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com

More information

INSTALLATION. Check that the idler pulley moves smoothly.

INSTALLATION. Check that the idler pulley moves smoothly. ENGINE MECHANICAL (5SFE) INSTALLATION EM23 EM08604 1. INSTALL OIL PUMP PULLEY (a) Align the cutouts of the pulley and shaft, and slide on the pulley. (b) Using, install the pulley nut. 0996010010 (0996201000,

More information

EG 18 ENGINE MECHANICAL TIMING BELT EG5EK 01 COMPONENTS FOR REMOVAL AND INSTALLATION

EG 18 ENGINE MECHANICAL TIMING BELT EG5EK 01 COMPONENTS FOR REMOVAL AND INSTALLATION EG18 ENGINE TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG5EK01 ENGINE EG19 EG20 ENGINE ENGINE EG21 EG22 ENGINE TIMING BELT REMOVAL EG5G101 1. REMOVE OIL PAN PROTECTOR 2. REMOVE ENGINE UNDER COVER

More information

Timing Belt: Service and Repair. Toyota Truck Sienna LE V6-3.0L (1MZ-FE) 2002

Timing Belt: Service and Repair. Toyota Truck Sienna LE V6-3.0L (1MZ-FE) 2002 Timing Belt: Service and Repair Toyota Truck Sienna LE V6-3.0L (1MZ-FE) 2002 REMOVAL 1. REMOVE OUTER FR COWL TOP PANEL ASSEMBLY 2. REMOVE RH FRONT WHEEL 3. REMOVE RH FENDER APRON SEAL 4. REMOVE GENERATOR

More information

TIMING BELT COMPONENTS

TIMING BELT COMPONENTS EG134 3SGTE ENGINE TIMING BELT COMPONENTS 3SGTE ENGINE EG135 EG136 3SGTE ENGINE 3SGTE ENGINE TIMING BELT REMOVAL EG137 (See Components for Removal and Installation) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL

More information

ALLDATA Online Toyota Camry Wagon L4-2.0L (3S-FE) - Timing Belt Installat... Page 1 of 15. Timing Belt Installation. Timing Belt (3S-FE)

ALLDATA Online Toyota Camry Wagon L4-2.0L (3S-FE) - Timing Belt Installat... Page 1 of 15. Timing Belt Installation. Timing Belt (3S-FE) ALLDATA Online - 1990 Toyota Camry Wagon L4-2.0L (3S-FE) - Timing Belt Installat... Page 1 of 15 Timing Belt Installation Timing Belt (3S-FE) INSTALLATION OF TIMING BELT 1. INSTALL OIL PUMP PULLEY a. Align

More information

EG-37 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION 2JZ-GE

EG-37 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION 2JZ-GE ENGINE EG37 TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION 2JZGE EG38 ENGINE 2JZ GTE ENGINE EG39 TIMING BELT REMOVAL (See Components for Removal and Installation) 1. REMOVE BATTERY AND BATTERY TRAY

More information

2003 Toyota Truck Highlander 2WD V6-3.0L (1MZ-FE) Copyright 2013, ALLDATA Page 1

2003 Toyota Truck Highlander 2WD V6-3.0L (1MZ-FE) Copyright 2013, ALLDATA Page 1 2003 Toyota Truck Highlander 2WD V6-3.0L (1MZ-FE) Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair TIMING BELT REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FRONT FENDER APRON SEAL

More information

TIMING BELT (1MZ FE Jan., 2003)

TIMING BELT (1MZ FE Jan., 2003) 14 100 TIMING BELT (1MZ FE Jan., 2003) REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FRONT FENDER APRON SEAL RH 3. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1 (See Pub. No. RM972U on page

More information

12. REMOVE ENGINE MOVING CONTROL ROD (a) Remove the 4 bolts, the engine moving control rod and the bracket.

12. REMOVE ENGINE MOVING CONTROL ROD (a) Remove the 4 bolts, the engine moving control rod and the bracket. TIMING BELT (3MZFE) REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FR WIPER ARM RH (See page 669) 3. REMOVE FR WIPER ARM LH (See page 669) 4. REMOVE COWL TOP VENTILATOR LOUVER SUBASSY (See page 669) 5.

More information

2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.

2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. TIMING BELT NOTE: On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. Removal 1. Remove the engine cover. See Fig. 1. 2. Remove right

More information

REPLACEMENT. 12. REMOVE ENGINE MOVING CONTROL ROD (a) Remove the 5 bolts, the engine moving control rod and the engine mounting stay.

REPLACEMENT. 12. REMOVE ENGINE MOVING CONTROL ROD (a) Remove the 5 bolts, the engine moving control rod and the engine mounting stay. 1484 ENGINE MECHANICAL REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FRONT WIPER ARM HEAD CAP 3. REMOVE FR WIPER ARM RH (See page 668 ) 4. REMOVE FR WIPER ARM LH (See page 668 ) 5. REMOVE COWL TOP VENTILATOR

More information

ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT INSPECTION OF ENGINE OIL INSPECTION OF BATTERY. INSPECTION OF AIR FILTER (Paper Filter Type)

ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT INSPECTION OF ENGINE OIL INSPECTION OF BATTERY. INSPECTION OF AIR FILTER (Paper Filter Type) ENGINE MECHANICAL - Engine Tune-Up EM-17 ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT (See steps 1 and 2 on page CO-4) INSPECTION OF ENGINE OIL (See steps 1 and 2 on page LU-5) INSPECTION OF BATTERY (See

More information

INSTALLATION EM 21. Inward. Sensor. Plate Washer. 10 mm Hexagon Wrench SST. Fulcrum Length SST TIMING BELT ENGINE MECHANICAL 2002 AVALON (RM872U)

INSTALLATION EM 21. Inward. Sensor. Plate Washer. 10 mm Hexagon Wrench SST. Fulcrum Length SST TIMING BELT ENGINE MECHANICAL 2002 AVALON (RM872U) Inward Sensor A05060 INSTALLATION EM21 EM0ZD02 1. INSTALL CRANKSHAFT TIMING PULLEY (a) Align the pulley set key with the key groove of the timing pulley, and slide on the timing pulley. (b) Install the

More information

INSTALLATION. 6. SET NO.1 CYLINDER TO TDC/COMPRESSION (a) Temporarily install the crankshaft pulley bolt to the crankshaft.

INSTALLATION. 6. SET NO.1 CYLINDER TO TDC/COMPRESSION (a) Temporarily install the crankshaft pulley bolt to the crankshaft. EM19 ENGINE MECHANICAL (5VZFE) INSTALLATION EM0Z003 1. INSTALL CRANKSHAFT TIMING PULLEY (a) Align the pulley set key with the key groove of the timing pulley and slide on the timing pulley. (b) Slide on

More information

2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE)

2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE) 2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE) Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair TIMING CHAIN TIMING CHAIN http://alldatapro.com/alldata/pro~v440713400~c39519~r0~od~n/0/108596970/110859775/110859788/110859790/34853741/100411974/34853743/56492475

More information

INSTALLATION. NOTICE: Do not scratch the angle sensor of the timing pulley.

INSTALLATION. NOTICE: Do not scratch the angle sensor of the timing pulley. EM26 INSTALLATION EM11B01 1. INSTALL OIL PUMP PULLEY (a) Align the cutouts of the pulley and shaft, and slide on the pulley. (b) Using, install the pulley nut. 0996010010 (0996201000, 0996300600) Torque:

More information

Service and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly.

Service and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly. Service and Repair REPLACEMENT 1. SEPARATE BATTERY NEGATIVE TERMINAL 2. REMOVE AIR CLEANER INLET NO.1 3. DRAIN ENGINE COOLANT 4. REMOVE V-BANK COVER 5. REMOVE INTAKE AIR CONNECTOR PIPE 6. REMOVE ENGINE

More information

EM 6 VALVE CLEARANCE ENGINE MECHANICAL EM11I 01 ADJUSTMENT HINT:

EM 6 VALVE CLEARANCE ENGINE MECHANICAL EM11I 01 ADJUSTMENT HINT: EM6 ADJUSTMENT EM11I01 Inspect and adjust the valve clearance when the engine is cold. 1. REMOVE NO.1 ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE AIR CLEANER INLET 4. REMOVE AIR CLEANER ASSEMBLY

More information

2012 Kia Soul L4 2.0L

2012 Kia Soul L4 2.0L 2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 1 Removal Engine removal is not required for this procedure. CAUTION: Use fender

More information

REMOVAL. 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE RADIATOR ASSEMBLY (See page CO 1 5) 4. REMOVE DRIVE BELT (See page 1) CH

REMOVAL. 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE RADIATOR ASSEMBLY (See page CO 1 5) 4. REMOVE DRIVE BELT (See page 1) CH ENGINE MECHANICAL (2JZGE) EM1 7 REMOVAL EM1S301 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE RADIATOR ASSEMBLY (See page CO 1 5) 4. REMOVE DRIVE BELT (See page 1) CH 5. REMOVE PS PUMP

More information

TIMING CHAIN COMPONENTS

TIMING CHAIN COMPONENTS h Page 1 of 52 TIMING CHAIN COMPONENTS ht Page 2 of 52 Fig. 24: Displaying Timing Chain Components (1 Of 2) Page 3 of 52 Fig. 25: Displaying Timing Chain Components (2 Of 2) Page 4 of 52 REMOVAL NOTE:

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Raise and

More information

VALVE CLEARANCE INSPECTION

VALVE CLEARANCE INSPECTION ENGINE MECHANICAL (2RZFE, 3RZFE) INSPECTION EM5 EM02K06 Inspect and adjust the valve clearance when the engine is cold. 1. REMOVE INTAKE AIR CONNECTOR (See page EM34) 2. REMOVE PCV HOSES 3. REMOVE IGNITION

More information

Page 1 of 44 REPLACEMENT 1. 2. 3. 4. REMOVE ENGINE UNDER COVER RH DRAIN COOLANT (See REPLACEMENT ) REMOVE FRONT WHEEL RH REMOVE CYLINDER HEAD COVER NO. 2 a. Remove the 2 nuts, 2 clips and cylinder head

More information

REPLACEMENT HINT: 11. REMOVE V RIBBED BELT TENSIONER ASSY (a) Remove the 5 bolts and V ribbed belt tensioner.

REPLACEMENT HINT: 11. REMOVE V RIBBED BELT TENSIONER ASSY (a) Remove the 5 bolts and V ribbed belt tensioner. 14142 REPLACEMENT HINT: ENGINE MECHANICAL Refer to CAMSHAFT (RH BANK) or CAMSHAFT (LH BANK) for the replacement procedure of the No.2 chain (see page 14157 or 14175). 1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION Page 1 of 11 REMOVAL & INSTALLATION TIMING BELT Tips Click a link to view tip Tech1 Question: Timing problems P0340 Tech1 Question: 2.2 TIMING PROBLEMS - RESOLVED Removal Tips Click a link to view tip

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower

More information

10. SEPARATE COMPRESSOR (a) Remove the nut, 3 bolts compressor stay and compressor. HINT: Hang up the hoses instead of detaching.

10. SEPARATE COMPRESSOR (a) Remove the nut, 3 bolts compressor stay and compressor. HINT: Hang up the hoses instead of detaching. 14108 ENGINE MECHANICAL REPLACEMENT 1. DRAIN ENGINE COOLANT(See page165 ) 2. SEPARATE BATTERY NEGATIVE TERMINAL 3. REMOVE VBANK COVER SUBASSY (a) Remove the 2 cap nuts and Vbank cover subassy. 4. REMOVE

More information

REMOVAL. 5. REMOVE OIL DIPSTICK GUIDE (a) Remove the bolt, dipstick guide and engine wire bracket. (b) Remove the O ring from the dipstick guide.

REMOVAL. 5. REMOVE OIL DIPSTICK GUIDE (a) Remove the bolt, dipstick guide and engine wire bracket. (b) Remove the O ring from the dipstick guide. EM34 ENGINE MECHANICAL (2RZFE, 3RZFE) P23426 EM1MY01 REMOVAL 1. DRAIN ENGINE COOLANT 2. DISCONNECT THESE CABLES: (a) Disconnect the accelerator cable from the throttle body. A/T: Disconnect the throttle

More information

Page 1 of 25. Service and Repair REMOVAL SIZED FOR PRINT. Related Components

Page 1 of 25. Service and Repair REMOVAL SIZED FOR PRINT. Related Components Page 1 of 25 Service and Repair REMOVAL Related Components Page 2 of 25 1ZZ-FE Page 3 of 25 2ZZ-GE 1. REMOVE UPPER FRONT FENDER APRON SEAL AND UPPER RADIATOR SUPPORT SEAL 2. DRAIN ENGINE COOLANT 3. REMOVE

More information

2011 > G 1.6 DOHC > Language. [MDPS Type] Loosen the mounting bolts (A) and then, turn the adjusting bolt(b) clockwise in loose tension.

2011 > G 1.6 DOHC > Language. [MDPS Type] Loosen the mounting bolts (A) and then, turn the adjusting bolt(b) clockwise in loose tension. 2011 > G 1.6 DOHC > Language Removal Engine removal is not required for this procedure. 1. Disconnect the battery negative terminal. 2. Loosen the water pump pulley bolt and the drive idler mounting bolt.

More information

VALVE CLEARANCE (K3-VE)

VALVE CLEARANCE (K3-VE) ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) 25 ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) INSPECTION 1. DISCONNECT NEGATIVE BATTERY TERMINAL (See page RS-164.) 2. ROVE ENGINE UNDER COVER 3. DRAIN ENGINE COOLANT

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. On Millenia, raise and support vehicle. Remove right front wheel. Remove lower engine covers. 2. On all models, remove accessory

More information

CHARGING SYSTEM CHARGING SYSTEM CH 1

CHARGING SYSTEM CHARGING SYSTEM CH 1 CH1 CH2 Precautions PRECAUTIONS 1. Check that the battery cables are connected to the correct terminals. 2. Disconnect the battery cables when the battery is given a quick charge. 3. Do not perform tests

More information

TUNE UP EG2 12 ENGINE MECHANICAL

TUNE UP EG2 12 ENGINE MECHANICAL EG212 TUNEUP 1. CHECK COOLANT LEVEL AT RESERVOIR TANK The engine coolant level should be between the LOW and FULL lines. If low, check for leaks and add engine coolant up to the FULL line. 2. CHECK COOLANT

More information

GENERATOR CH-9 COMPONENTS FOR REMOVAL AND INSTALLATION

GENERATOR CH-9 COMPONENTS FOR REMOVAL AND INSTALLATION CH9 COMPONENTS FOR REMOVAL AND INSTALLATION CH10 REMOVAL (See Components for Removal and Installation) 1. DISCONNECT NEGATIVE TERMINAL CABLE FROM BATTERY CAUTION: Work must be started after 90 seconds

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Noting position for installation reference, disconnect secondary wires from spark plugs. Remove spark plugs. 2. Disconnect negative battery cable. Remove air

More information

REMOVAL. 16. LOOSEN CRANKSHAFT PULLEY BOLT Using SST, loosen the pulley bolt. SST ( ), EM 20 SST TIMING BELT

REMOVAL. 16. LOOSEN CRANKSHAFT PULLEY BOLT Using SST, loosen the pulley bolt. SST ( ), EM 20 SST TIMING BELT EM20 REMOVAL EM11901 1. REMOVE NO.1 ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE AIR CLEANER INLET 4. REMOVE AIR CLEANER ASSEMBLY 5. REMOVE NO.2 CYLINDER HEAD COVER 6. REMOVE IGNITION COILS (See

More information

CAMSHAFT (LH BANK) (2GR FE) ENGINE MECHANICAL 1424N 01 REPLACEMENT

CAMSHAFT (LH BANK) (2GR FE) ENGINE MECHANICAL 1424N 01 REPLACEMENT REPLACEMENT N0. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE ). REMOVE ENGINE WIRE 3. REMOVE FRONT FRAME ASSY (SEE PAGE ). REMOVE STARTER ASSY (SEE PAGE 99). REMOVE AUTOMATIC TRANSAXLE ASSY (SEE PAGE

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal (200SX & 300ZX)

More information

Fig. 1: Remove the bolts which fasten the upper timing belt cover... Fig. 2:... and remove the cover

Fig. 1: Remove the bolts which fasten the upper timing belt cover... Fig. 2:... and remove the cover Show Timing Belt and Covers REMOVAL & INSTALLATION 1983 87 626 NOTE: For access, safely support the car, then remove the right front wheel and splash shield. 1. Loosen the alternator mounting bolts and

More information

2012 Kia Soul L4 2.0L

2012 Kia Soul L4 2.0L 2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 2 Installation 1. The TDC marks of the intake and exhaust CVVT sprockets are

More information

Timing Belt Removal. CAUTION: Inspect the water pump when replacing the timing belt (page 10-9). 4. Remove the P/S bracket.

Timing Belt Removal. CAUTION: Inspect the water pump when replacing the timing belt (page 10-9). 4. Remove the P/S bracket. Timing Belt Removal CAUTION: Inspect the water pump when replacing the timing belt (page 10-9). Turn the crankshaft so that No. 1 piston is at top dead center (page 6-64). Before removing the timing belt,

More information

1996 Isuzu Truck Rodeo (2WD) V6-3165cc 3.2L SOHC (6VD1)

1996 Isuzu Truck Rodeo (2WD) V6-3165cc 3.2L SOHC (6VD1) 1996 Isuzu Truck Rodeo (2WD) V6-3165cc 3.2L SOHC (6VD1) Service and Repair Notes REMOVAL STEPS Preparation: Battery ground cable 1. Radiator upper fan shroud Remove from radiator. 2. Cooling fan assembly

More information

1ZZ-FE ENGINE MECHANICAL ENGINE UNIT DISASSEMBLY. If you paid for the content in this manual you were screwed!

1ZZ-FE ENGINE MECHANICAL ENGINE UNIT DISASSEMBLY. If you paid for the content in this manual you were screwed! 1ZZ-FE ENGINE MECHANICAL ENGINE UNIT 107 DISASSBLY 1. ROVE OIL FILLER CAP SUB-ASSBLY (a) Remove the oil filler cap from the cylinder head cover. A064852 A065656 A064854 2. ROVE OIL FILLER CAP GASKET (a)

More information

INTEGRATED IGNITION ASSEMBLY (IIA) (4A FE)

INTEGRATED IGNITION ASSEMBLY (IIA) (4A FE) IG20 IGNITION SYSTEM Integrated Ignition Assembly (11A) (4AFE) INTEGRATED IGNITION ASSEMBLY (IIA) (4AFE) REMOVAL OF IIA 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started

More information

2001 Toyota MR ENGINES' '1.8L 4-Cylinder

2001 Toyota MR ENGINES' '1.8L 4-Cylinder TIMING CHAIN Removal 1. Disconnect negative battery cable. Drain cooling system. On Corolla, remove windshield washer fluid reservoir. On Celica, remove upper front fender apron seal and upper radiator

More information

Intake Manifold: Service and Repair Removal

Intake Manifold: Service and Repair Removal 1992 Toyota Truck Pickup 2WD V6-180.5 2959cc 3.0L SOHC (3VZ-E) Copyright 2013, ALLDATA 10.52 Page 1 Intake Manifold: Service and Repair Removal NOTE: If removing and later reinstalling the fluid coupling

More information

REPLACEMENT. 1. REMOVE CYLINDER HEAD COVER NO.2 (a) Remove the 4 nuts and cylinder head cover No. 2.

REPLACEMENT. 1. REMOVE CYLINDER HEAD COVER NO.2 (a) Remove the 4 nuts and cylinder head cover No. 2. ENGINE MECHANICAL 1475 REPLACEMENT 141FV01 1. REMOVE CYLINDER HEAD COVER NO.2 (a) Remove the 4 nuts and cylinder head cover No. 2. A66316 2. REMOVE IGNITION COIL NO.1 (a) Remove the 4 bolts and pull out

More information

Technical Service BULLETIN

Technical Service BULLETIN Technical Service BULLETIN May 19, 2003 Title: Models: 00 02 Celica GTS EG010-03 ENGINE Introduction In some cases, owners of 2000 2002 model year Celica GTS vehicles equipped with the 2ZZ GE engine may

More information

ENGINE MECHANICAL > VALVE CLEARANCE INSPECTION > 2.5L >

ENGINE MECHANICAL > VALVE CLEARANCE INSPECTION > 2.5L > Print 2003 Subaru Forester 2.5L Eng X ENGINE CONTROLS - ON-VEHICLE ADJUSTMENTS ENGINE MECHANICAL > VALVE CLEARANCE INSPECTION > 2.5L > 1. Set the vehicle onto the lift. 2. Lift-up the vehicle. 3. Remove

More information

11. REMOVE OIL PAN SUB ASSY NO.2 (a) Remove the 18 bolts and 2 nuts.

11. REMOVE OIL PAN SUB ASSY NO.2 (a) Remove the 18 bolts and 2 nuts. 1444 ENGINE MECHANICAL REPLACEMENT 1. REMOVE ENGINE ASSEMBLY (SEE PAGE 1419) 2. REMOVE DRIVE PLATE & RING GEAR SUBASSY (AUTOMATIC TRANSMISSION) (SEE PAGE 1419) SST 0921354015 (9165160855), 0933000021 3.

More information

REAR DRIVE SHAFT (3S GTE ENGINE)

REAR DRIVE SHAFT (3S GTE ENGINE) SA52 REAR DRIVE SHAFT (3SGTE ENGINE) COMPONENTS SA53 NOTICE: The axle bearing could be damaged if it is subjected to the vehicle weight, such as when moving the vehicle with the drive shaft removed. Therefore,

More information

3/13/ :32 AM. NOTICE: Do not disconnect the hose.

3/13/ :32 AM. NOTICE: Do not disconnect the hose. 1 of 25 REPLACEMENT 1. REMOVE HOOD SUB-ASSEMBLY 2. REMOVE FRONT WHEEL RH 3. REMOVE ENGINE UNDER COVER LH 4. REMOVE ENGINE UNDER COVER RH 5. REMOVE FRONT FENDER APRON SEAL RH 6. DRAIN ENGINE OIL a. Install

More information

25. REMOVE OIL PIPE NO.1 (a) Remove the 2 oil pipe unions, and oil pipe No.1. (b) Remove the oil control valve filter LH and gaskets.

25. REMOVE OIL PIPE NO.1 (a) Remove the 2 oil pipe unions, and oil pipe No.1. (b) Remove the oil control valve filter LH and gaskets. CAMSHAFT (RH BANK) (2GRFE) REPLACEMENT 1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE 1421) 2. REMOVE ENGINE WIRE 3. REMOVE FRONT FRAME ASSY (SEE PAGE 1421) 4. REMOVE STARTER ASSY (SEE PAGE 199). REMOVE

More information

2003 Cadillac CTS V6-3.2L VIN N

2003 Cadillac CTS V6-3.2L VIN N 1 of 16 5/11/2013 11:18 AM 2003 Cadillac CTS V6-3.2L VIN N Vehicle» Engine, Cooling and Exhaust» Engine» Timing Belt» Service and Repair» Timing Belt Replacement Timing Belt Replacement Tools Required

More information

DISTRIBUTOR DISTRIBUTOR REMOVAL

DISTRIBUTOR DISTRIBUTOR REMOVAL IG12 (5SFE) DISTRIBUTOR DISTRIBUTOR REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION (w / Airbag): Work must be started after approx. 30 seconds or longer from the time the ignition

More information

Timing Belt: Service and Repair Timing Belt Replacement

Timing Belt: Service and Repair Timing Belt Replacement 2000 Cadillac Catera V6-3.0L VIN R Copyright 2006, ALLDATA 8.80 Page 1 Timing Belt: Service and Repair Timing Belt Replacement TIMING BELT REPLACEMENT Removal Procedure ^ Tools Required - J 42069 Timing

More information

2003 Hyundai Sonata LX

2003 Hyundai Sonata LX TIMING & COUNTERBALANCE SHAFT BELTS Removal CAUTION: DO NOT rotate engine counterclockwise (as viewed from timing belt end of engine). If reusing timing belt, place reference mark on timing belt to indicate

More information

TIMING BELT TIMING BELT

TIMING BELT TIMING BELT TIMING BELT TIMING BELT DISASSEMBLY 1. Lift the vehicle by using of jack. 2. Remove the engine support bracket. (14 mm bolt and 2 nuts, 17 mm bolt) 3. Remove the power steering belt. 4. Remove the air

More information

REMOVAL AND INSTALLATION

REMOVAL AND INSTALLATION 2006 Eclipse (2.4L 4G69) REMOVAL AND INSTALLATION Report a problem with this article Pre-removal Operation Side Under Cover Removal (Refer to GROUP 51, Under Cover Post-installation Operation Crankshaft

More information

REMOVAL AND REPLACEMENT

REMOVAL AND REPLACEMENT 2002 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Vehicle > Engine, Cooling and Exhaust > Engine > Timing Components > Timing Belt > Service and Repair REMOVAL AND REPLACEMENT https://my.alldata.com/repair/#/repair/article/36847/component/64/itype/401/nonstandard/

More information

Timing Belt: Service and Repair TIMING BELT

Timing Belt: Service and Repair TIMING BELT 2008 Hyundai Accent L4-1.6L Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair TIMING BELT EMOVAL Engine removal is not required for this procedure. 1. Remove the engine cover. 2. Remove

More information

1995 Mitsubishi Montero LS. Ensure timing marks are aligned. Mark timing belt direction of rotation.

1995 Mitsubishi Montero LS. Ensure timing marks are aligned. Mark timing belt direction of rotation. TIMING BELT NOTE: Ensure timing marks are aligned. Mark timing belt direction of rotation. Removal 1. Disconnect negative battery cable. Drain engine coolant. Remove engine coolant reservoir tank, fan

More information

VALVE CLEARANCE (1NZ-FXE)

VALVE CLEARANCE (1NZ-FXE) 146 ENGINE MECHANICAL ADJUSTMENT 1. REMOVE REAR FLOOR BOARD NO.2 (See page 211 16) 2. REMOVE DECK FLOOR BOX REAR (See page 211 16) 3. REMOVE REAR FLOOR BOARD NO.3 (See page 211 16) 4. DISCONNECT BATTERY

More information

a. Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.

a. Turn the crankshaft pulley, and align its groove with the timing mark 0 of the timing chain cover. Adjustments ADJUSTMENT HINT: Inspect and adjust the valve clearance when the engine is cold. 1. REMOVE CYLINDER HEAD COVER 2. SET NO. 1 CYLINDER TO TDC/COMPRESSION a. Turn the crankshaft pulley, and align

More information

WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.

WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components. 4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,

More information

1990 Nissan-Datsun 300ZX V6-2960cc DOHC Turbo (VG30DETT) Service and Repair TIMING BELT REPLACEMENT

1990 Nissan-Datsun 300ZX V6-2960cc DOHC Turbo (VG30DETT) Service and Repair TIMING BELT REPLACEMENT 1990 Nissan-Datsun 300ZX V6-2960cc DOHC Turbo (VG30DETT) Service and Repair TIMING BELT REPLACEMENT CAUTION: a. Do not bend or twist timing belt. b. After removing timing belt, do not turn crankshaft and

More information

OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE CYLINDER HEAD COVER SUB ASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.

OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE CYLINDER HEAD COVER SUB ASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket. 144 ENGINE MECHANICAL OVERHAUL 1. REMOVE OIL FILLER CAP SUBASSY 1410H01 2. REMOVE CYLINDER HEAD COVER SUBASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket. A11090 3. REMOVE CAMSHAFT

More information

TIMING BELT REMOVAL/INSTALLATION [ZM]

TIMING BELT REMOVAL/INSTALLATION [ZM] ALLDATA Online - 2000 Mazda Protege LX L4-6L DOHC - Service an... 1 of 8 6/26/2012 7:53 PM TIMING BELT REMOVAL/INSTALLATION [ZM] 5. 6. 7. 8. 9. Disconnect the negative battery cable. Remove the CMP sensor.

More information

Timing Belt. Removal ENGINE MECHANICAL (6VD1 3.2L) 6A-27

Timing Belt. Removal ENGINE MECHANICAL (6VD1 3.2L) 6A-27 Removal 1. Disconnect battery ground cable. 2. Remove air cleaner assembly. 3. Remove radiator upper fan shroud from radiator. 4. Move drive belt tensioner to loose side using wrench then remove drive

More information

Toyota Truck Pickup 2WD L4-2.4L SOHC (22R) 1987

Toyota Truck Pickup 2WD L4-2.4L SOHC (22R) 1987 Timing Chain: Service and Repair Toyota Truck Pickup 2WD L4-2.4L SOHC (22R) 1987 PREPARATION FOR REMOVAL OF TIMING CHAIN 1. REMOVE CYLINDER HEAD 2. REMOVE RADIATOR 3. REMOVE OIL PAN (a) Remove the engine

More information

INTEGRATED IGNITION ASSEMBLY (IIA)

INTEGRATED IGNITION ASSEMBLY (IIA) (4AFE) IG7 Pickup coil resistance (Hot): G (+) and G () 240325 NE(+) and G() 475650 If the resistance is not as specified, replace the distributor housing assembly. 9. REINSTALL IGNITION COIL DUST COVER

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING & COUNTERBALANCE SHAFT BELTS

More information

OVERHAUL. 1. REMOVE OIL FILLER CAP SUB ASSY (a) Remove the oil filler cap from the cylinder head cover.

OVERHAUL. 1. REMOVE OIL FILLER CAP SUB ASSY (a) Remove the oil filler cap from the cylinder head cover. 1452 ENGINE MECHNICL OVERHUL 140QU01 1. REMOVE OIL FILLER CP SUSSY (a) Remove the oil filler cap from the cylinder head cover. 64852 2. REMOVE OIL FILLER CP GSKET (a) Using a screwdriver, remove the gasket

More information

REMOVAL. Engine removal is not required for this procedure. Remove the engine cover(a).

REMOVAL. Engine removal is not required for this procedure. Remove the engine cover(a). 1 of 25 12/11/2012 4:43 PM REMOVAL Engine removal is not required for this procedure. 1. Remove the engine cover(a). 2. 3. Remove the RH front wheel. Remove the 2 bolts(b) and RH side cover(a). 2 of 25

More information

FRONT AXLE AND SUSPENSION FA 1

FRONT AXLE AND SUSPENSION FA 1 FRONT AXLE AND SUSPENSION FA1 FRONT AXLE AND SUSPENSION FA2 FRONT AXLE AND SUSPENSION Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Page Wanders/pulls Tires worn or improperly inflated

More information

VALVE CLEARANCE (3ZZ FE/4ZZ FE)

VALVE CLEARANCE (3ZZ FE/4ZZ FE) ENGINE MECHANICAL ADJUSTMENT 1. REMOVE CYLINDER HEAD COVER NO.2 1487 140M901 Remove the 2 nuts, 2 clips and cylinder head cover. 2. REMOVE IGNITION COIL ASSY Disconnect the 4 connectors. (b) Remove the

More information

LU 8 LUBRICATION SYSTEM. Oil Pump OIL PUMP COMPONENTS

LU 8 LUBRICATION SYSTEM. Oil Pump OIL PUMP COMPONENTS LU8 OIL PUMP COMPONENTS LU9 REMOVAL OF OIL PUMP (See page LU8) 1. RAISE VEHICLE NOTICE: Be sure the vehicle is securely supported. 2. REMOVE ENGINE UNDERCOVER 3. DRAIN ENGINE OIL (a) Remove the oil filler

More information

Remove four nuts, then the cooling fan assembly.

Remove four nuts, then the cooling fan assembly. The DOHC and SOHC engines both use the same Service and Repair procedure from Isuzu. Make note that the DOHC and SOHC engines both use a single gear for the camshaft but use different alignment marks.

More information

ENGINE TUNE UP. (See steps 1 and 2 on page CO 5)

ENGINE TUNE UP. (See steps 1 and 2 on page CO 5) EM12 ENGINE MECHANICAL ENGINE TUNEUP INSPECTION OF ENGINE COOLANT (See steps 1 and 2 on page CO5) INSPECTION OF ENGINE OIL (See steps 1 and 2 on page LU5) INSPECTION OF BATTERY (See steps 1 and 2 on page

More information

26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]

26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ] Last Modified: 8-24-2016 6.6 A Doc ID: RM000000T4X000X Model Year Start: 2006 Model: GS300 Prod Date Range: [01/2005 - ] Title: 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/2005

More information

3. Using the ST, align the Top mark on crank sprocket to nine o clock position as shown in the figure

3. Using the ST, align the Top mark on crank sprocket to nine o clock position as shown in the figure 2008 Tribeca (3.6L) MECHANICAL(H6DO) > Timing Chain Assembly Report a problem with this article INSTALLATION Be careful that the foreign matter is not into or onto assembled component during installation.

More information

DISTRIBUTOR (5S FE) REMOVAL OF DISTRIBUTOR IG 30

DISTRIBUTOR (5S FE) REMOVAL OF DISTRIBUTOR IG 30 IG30 IGNITION SYSTEM Distributor (5SFE) DISTRIBUTOR (5SFE) REMOVAL OF DISTRIBUTOR 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started after approx. 20 seconds or longer

More information

1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION (2007 4Runner) Model Year: 2007 Model: 4Runner Doc ID: RM WS002X

1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION (2007 4Runner) Model Year: 2007 Model: 4Runner Doc ID: RM WS002X Last Modified: 4-26-2007 Service Category: Engine/Hybrid System 1.6 A Section: Engine Mechanical Model Year: 2007 Model: 4Runner Doc ID: RM0000029WS002X Title: 1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION

More information

2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page 1. Timing Belt: Service and Repair

2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page 1. Timing Belt: Service and Repair 2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page 1 Timing Belt: Service and Repair 2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page

More information

Toyota Truck Tacoma Extra Cab 2WD L4-2.4L (2RZ-FE) Timing Chain: Service and Repair

Toyota Truck Tacoma Extra Cab 2WD L4-2.4L (2RZ-FE) Timing Chain: Service and Repair Toyota Truck Tacoma Extra Cab 2WD L4-2.4L (2RZ-FE) 2002 Timing Chain: Service and Repair REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE OIL 3. 4 WD: REMOVE FRONT DIFFERENTIAL AND DRIVE SHAFTS

More information

ALLDATA Online Ford Focus L4-2.0L DOHC VIN 5 - Service and Repair. Service and Repair

ALLDATA Online Ford Focus L4-2.0L DOHC VIN 5 - Service and Repair. Service and Repair Page 1 of 22 Service and Repair NOTE: Ford does not provide camshaft gear timing marks, or information to perform timing belt service without the special tools shown in this procedure. Timing Belt Special

More information

Removal. All vehicles. Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair. Special Tool(s) Check Pin - Camshaft Pulleys

Removal. All vehicles. Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair. Special Tool(s) Check Pin - Camshaft Pulleys Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair Special Tool(s) Check Pin - Camshaft Pulleys 303-1132 Timing Pin - Camshaft Pulleys 303-1126 Timing Pin - Automatic Transmission

More information

Timing Belt: Service and Repair Installation NOTE: Check the water pump for water leakage and the oil seal for oil leakage.

Timing Belt: Service and Repair Installation NOTE: Check the water pump for water leakage and the oil seal for oil leakage. 1991 Daihatsu Truck Rocky L4-1589cc 1.6L SOHC Page 1 Timing Belt: Service and Repair Installation NOTE: Check the water pump for water leakage and the oil seal for oil leakage. Repair any water leakage

More information