BATH FILLER & BATH / SHOWER MIXER Installation & aftercare instructions

Transcription

1 GENERAL NOTES This mixer should be installed in accordance with water regulations. Approved check valves should be fitted where required. For further details please contact your local water authority. Should the mixer fail to operate effectively it may be that there is insufficient water pressure. Similarly, hot & cold water supplies should be relatively balanced for optimum performance. A reputable plumber will be able to advise on each of these issues. BATH FILLER & BATH / SHOWER MIXER Installation & aftercare instructions Please retain for future reference AFTERCARE INSTRUCTIONS Whilst this item has a high quality durable finish, it should nevertheless be treated with care. Surfaces should be cleaned using only a soft damp cloth and clean water & dried using a soft cotton cloth. Bath cleaning products, even non-scratch ones could damage the finished surface. 10-YEAR GUARANTEE We have complete confidence in this Roper Rhodes product and as such it is offered with a 10-year guarantee against defects in manufacture. The guarantee requires that this product be used in the manner for which it was intended and that it is installed & maintained in accordance with the fitting instructions and local water bylaws. The guarantee covers products in domestic use only. The guarantee is invalidated should the mixer be damaged by water borne debris. Make sure that supply pipes are clear of any debris prior to installation, this is particularly important on new plumbing installations. In the unlikely event that this product should fail during the guarantee period we will either replace the faulty part or the complete unit as appropriate. WESSEX T / T Customer Services, Roper Rhodes Ltd, Brassmill Lane Trading Estate, Bath, BA1 3JF TEL: FAX: sales@roperrhodes.co.uk Web: REF: NH.RR.T V1.00

2 Additional Instructions for Bath / Shower Mixers Only 7. Attach the end of the shower hose with the large nut shaped fitting to the bottom of the diverter valve. The other end should be attached to the shower head (see diagram). 8. Establish the desired position for the shower head wall-mounting bracket. Check that the bracket is oriented correctly & that the shower head will reach by placing it temporarily in position. Caution: Before drilling, check for hidden power cables and pipes. Take care using power tools, especially near water. The use of a residual current device (RCD) is recommended. Bath filler 9. Drill a single 8mm hole in the desired position for the shower head mounting bracket and insert the supplied nylon plug into the hole. 10. Disassemble the wall mounting bracket by unscrewing the cover cap from the cover plate and insert the supplied screw through the centre of the cover plate and screw into the wall, making sure the O-ring is placed between the wall and cover plate. Re-assemble the bracket in the order shown and place the shower head in position. Base plate 3/4" BSP Arm Cover cap Spring plate Spring Screw Cover plate O-ring Rubber washer Plastic washer Brass nut Shower head INSTALLATION PROCEDURE 1. Prior to installation flush out the pipe work to remove debris & then ensure that the water supply is turned off. 2. Refer to diagram & check that all components are present. Diverter valve (Clockwise - spout, Anti-clockwise - shower) 3. Fit the bath filler / shower mixer to the bath using the brass nuts and the washers provided as indicated in the diagram. Remember to fit the base plates between the legs of the mixer and the bath. 4. Connect the hot & cold water supplies using PTFE tape to help create the seal. The hot supply should always be connected to the left hand side. 5 Fully open mixer on both hot & cold sides & allow water to run for approximately one minute to further flush the system. 6. Check all connections for leaks.

3 Contents Instructions for the removal of a tap cartridge Page 2 Instructions for the removal of a tap valve - Basin Mixer Page 3 Instructions for the removal of a tap valve - Bath Filler / Shower Mixer Page 4 Instructions for pop up waste replacement Page 5 Instructions for bath/shower mixer diverter replacement Page 7 Instructions for Storm bath/shower mixer diverter replacement Page 8 Instructions for fixing drip issue on Reef, Bora & Aero basin mixers Page 11 Page 1

4 Instructions for the removal of tap cartridge Page 2

5 Instructions for the removal of tap valve Basin mixer Before beginning any work ensure that the water supply is turned off Page 3

6 Instructions for the removal of tap valve Bath fi ller / shower mixer Before beginning any work ensure that the water supply is turned off Page 4

7 Instructions for pop up waste replacement POP-UP WASTE - mechanism replacement instructions STEP 1 Unscrew the plug top by rotating anti-clockwise STEP2 With the plug top removed you can access the brass pop-up mechanism. This can be unscrewed and removed by rotating anti-clockwise. Use a 9mm / adjustable spanner to grip the mechanism across the flats and rotate anti-clockwise. Page 5

8 Instructions for pop up waste replacement STEP3 Replace the faulty mechanism reversing the above steps to fit it. Page 6

9 Instructions for bath/shower mixer diverter replacement 1. Remove the face plate on the diverter handle. 2. Using a Phillips head screwdriver remove the screw and washers on the inside of the diverter handle. 3. Remove the diverter handle. 4. Using a 14mm socket and wrench unscrew the diverter axle. Nut faces this way Remove flow straightener 29mm Remove shower hose 23mm Paper clip 5. Remove the damaged diverter axle. 6. Check for any loose debris inside the diverter body and remove it. If none is not visible you should flush out the mixer by removing the flow straightener and shower hose and fully turn on both hot and cold taps. 7. Check the orientation of the nut on the replacement diverter axle (see diagram). If it is the wrong way around pull it off and put it back on the other way around. 8. Remove the o-ring from the damaged diverter axle and use it on the replacement axle. TIP a paper clip will be useful to help slide the o- ring off the damaged diverter axle. Insert the replacement diverter axle into position in the bath / shower mixer making sure the arm on the axle slots into the groove on the diverter mechanism. Page 7

10 Instructions for Storm bath/shower mixer diverter replacement Step 1. Remove the shower hose attachment from the diverter valve on the bath / shower mixer. Next remove the diverter handle. Do this by placing a flat head screwdriver into the base of the diverter valve on the underside of the spout (to stop it spinning whilst you unscrew the handle) [Figure 1]. Unscrew the diverter handle by turning anti-clockwise [Figure 2]. Figure 1 Figure 2 Step 2. Using a 12mm Allen key unscrew the diverter valve by turning anti-clockwise [Figure 3]. For an alternate method without the 12mm Allen key see Alternate Step 2 below. Page 8

11 Instructions for Storm bath/shower mixer diverter replacement Figure 3 Alternate Step 2. Using a 10mm spanner unscrew the diverter from the top of the spout, turning anticlockwise [Figure 4]. Figure 4 Step 3. Remove the diverter component from the underside of the spout [Figure 5]. Remove the flow straightener (using a suitable spanner) from the spout and flush out the bath shower mixer by turning on the hot and cold water to remove any debris which may be left behind from the damaged diverter component. Then proceed to fit the replacement component by reversing steps 2 and 1. Page 9

12 Instructions for Storm bath/shower mixer diverter replacement Figure 5 Replacement component: Page 10

13 Instructions for fixing drip issue on Reef, Bora & Aero basin mixers In most cases it s unlikely the valve component has failed. If the basin mixer is being used in a hard water area it s likely a build-up of limescale or damaged O-rings have caused the basin mixer to drip. Service valves on Bora basin mixer: 1. Shut off the water supply to the tap you are working on. 2. Unscrew the handle assembly by rotating the collar anti-clockwise. 3. Using a 17mm socket wrench or spanner loosen the valve by turning anti-clockwise. The valves can be tightly screwed in so take care not to damage the tap or basin. 4. Remove the valve and inspect the O-ring for damage. Clean it and the valve body. A wire brush maybe useful if a lot of limescale has built up on the valve. Also check the rubber seal on the base of the valve (colour coded for hot and cold). Clean this and make sure it has a flat surface. Page 11

14 Instructions for fixing drip issue on Reef, Bora & Aero basin mixers 6. Using tap grease (available from plumbers merchants) grease the O-rings and threads before re-installing the valves. 7. Re-fit the handles, turn the water supply back on and test the tap. Page 12

15 TECHNICAL INFORMATION - DIMENSIONS Wessex bath fi ller deck mounted T R G3/4 G3/4

16 TECHNICAL INFORMATION - FLOW RATES Wessex taps TAPS CODE LP/HP FLOW RATE (LITRES/MINUTE) AT BAR PRESSURE Wessex Basin Mixer T LP Wessex Deck Mounted Bath Filler T LP Wessex Deck Mounted Shower Bath Mixer T LP MIN PRESSURE KEY LP1 Taps Require Minimum Pressure Of 0.1 Bar LP2 Taps Require Minimum Pressure Of 0.2 Bar LP3 Taps Require Minimum Pressure Of 0.3 Bar HP Taps Require Minimum Pressure Of 0.5 Bar