OWNER'S MANUAL. Review this manual before operating your PRESTIGE PRO Powerhead P/N /17

Transcription

1 OWNER'S MANUAL Review this manual before operating your PRESTIGE PRO Powerhead P/N /17

2 PRESTIGE PRO POWERHEAD TABLE OF CONTENTS: SUBJECT PAGE Safety Instructions...3 Using your Prestige Pro Powerhead for the First Time... 4 General Operation...5 Performance Features Warning Indicator Light...6 Prestige Pro Attachments... 6 Maintenance and Care Brush Cleaning...7 Belt Removal and Replacement...8 Bulb Replacement...9 Limited Warranty...10 Service Information Copyright 2017 H-P Products, Inc.

3 IMPORTANT SAFETY INSTRUCTIONS Read These Instructions Before Using This Vacuum System When using an electrical appliance, basic precautions should always be followed, including the following: WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY: Unplug and disconnect power before servicing. Do not use on wet surfaces. Do not allow to be used as a toy. Close attention is necessary when used by or near children. Use only as direct in this manual. Use only manufacturer s recommended attachments. Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged or exposed to water, return it to a service center. Do no pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp objects or corners. Do not run appliance over cord. Keep cord away from heated surfaces. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. Do not handle system or appliance with wet hands. Do not put any objects into openings. Do not use with any opening blocked; keep free of dust, lint, hair and anything that may reduce airflow. Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts. Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes. Turn OFF all controls before unplugging. Use extra care when cleaning on stairs. Do not pick up flammable or combustible liquids such as gasoline or use it in any areas where they may be present. The hose contains electrical wires. Do not use if damaged, cut or punctured. Avoid picking up sharp objects. Always turn off this appliance before connecting or disconnecting either hose or powerhead. SAVE THESE INSTRUCTIONS Intended for Household Use Only 3

4 PRESTIGE PRO POWERHEAD USING YOUR PRESTIGE PRO POWERHEAD FOR THE FIRST TIME WARNING: Do not plug into electrical supply until assembly is complete. Failure to do so could result in electrical shock or injury. 1. Insert the wand into the opening located on the neck of the powerhead, it will click into place. 2. Insert the hose handle into the wand assembly. Insert the hose end into the inlet valve. If your hose has a pigtail, plug the 120v power cord into the nearest electrical outlet. 3. Push the power switch to the right (II) and lower the wand by pressing the handle release pedal on the back left side of the powerhead to begin vacuuming. (Fig. 1) To remove the wand, disconnect the power cord and step on the wand release pedal, then pull up on the wand. (Fig. 2) Adjustable Wand Wand Release Pedal Handle Release Pedal Height Indicator Window Height Adjustment Pedal Adjustable Wand Wand Release Pedal Jam Indicator Warning Light Circuit Protector/ Reset Button Handle Release Button Neck Soft Furniture Guard Xenon Headlight Fig. 1 Fig. 2 4 WARNING Always unplug the Prestige Pro powerhead before cleaning the brush area as the brush may suddenly restart. Failure to do so can result in personal injury.

5 GENERAL OPERATION The Prestige Pro is controlled by pressing the three position ON/OFF power control switch located on the hose handle. When the switch is pushed to the left (I) it turns on the vacuum only. When the switch is pushed to the right (II) it operates both the vacuum and the brush roller. The headlight will operate when the Prestige Pro is turned on. Carpet Height Adjustment Your powerhead has six different settings to clean a variety of carpet types and floor surfaces. The height adjustment pedal is located on the back right of the powerhead. To determine which setting you are currently on, look through the height indicator window on the top of the unit. You will see one of the six settings detailed below: XHI HI AUTO MED LO XLO Very Plush Carpet Plush Carpet General Carpet Thickness or Bare Floors Medium Pile Carpet Low Pile Carpet Indoor/Outdoor Carpet Height Indicator Window Height Adjustment Pedal Carpet Height Adjustment Tip: When using the Prestige Pro powerhead, start on the Auto setting. If pushing the powerhead feels difficult, then adjust to a higher setting. If the powerhead feels easy to push, you may want to lower the powerhead for more effective cleaning. The Auto setting is the recommended setting for hard floor surfaces (i.e. tile, vinyl, wood). CAUTION Do not attach or remove handle or wand while system is ON. This could cause sparking and damage the electrical contacts. 5

6 PRESTIGE PRO POWERHEAD PERFORMANCE FEATURES Warning Indicator Light Your powerhead is equipped with a circuit protector safety system that protects it from a possible jammed brush roller. The warning indicator light on top of the unit will change from green to red should a jam occur. If the circuit protector trips: 1. Turn your system OFF and unplug the Prestige Pro powerhead. 2. Remove the object preventing the brush roller from turning. 3. Locate the circuit protector reset button on the back right of the powerhead to reset the circuit protector. When the unit is turned back ON, the warning indicator light should be green. If the circuit protector trips again, repeat these steps. If this does not correct the issue, please contact your authorized service dealer for further assistance. PRESTIGE PRO ATTACHMENTS Handle Release Button Hose Handle Attachments- Using the Hose with Other Attachments If the Prestige Pro powerhead is attached to the wand, turn the system OFF before removing the hose handle from the wand. To disconnect the hose from the wand: 1. Press the black handle release button, then pull on the hose handle to disconnect from the wand. 2. Slide attachments firmly on handle as needed. Wand Assembly Attachments To remove the powerhead from the wand: Wand Release Pedal 1. Raise the wand to a vertical position so that it clicks into a locked position. 2. Press wand release pedal with your foot and pull the wand straight up and out of the Prestige Pro powerhead. 3. Put desired attachments on wand as needed. 6

7 MAINTENANCE AND CARE WARNING: Always unplug vacuum hose and wand before servicing and maintaining the Prestige Pro powerhead. Failure to do so could result in electrical shock or personal injury if unit suddenly starts. Always follow all safety precautions specified when caring for your Prestige Pro. Brush Cleaning Check the brush roller and brush support areas frequently in order to maintain optimum efficiency. If hair, string, thread, carpet fiber or lint become wound around the brush roller, remove by unwinding them by hand or carefully cutting with scissors. If build up becomes excessive, disconnect the Prestige Pro powerhead from the wand assembly and follow the brush roller removal steps below. Removing the Brush Roller Depending on usage and flooring type, the brush roller will become worn and will need to be replaced over time. To Remove the Brush Roller 1. Turn the powerhead over and take off the metal bottom plate by first unscrewing the two screws located by the rear wheels. 2. Remove the belt cover guard and pull the brush roller out. To Re-install the Brush Roller 1. Re-insert the brush roller back into the powerhead, making sure the belt is attached properly. 2. Insert the belt cover guard. 3. Place the metal bottom plate back onto the powerhead by inserting the front end of the bottom plate first. 4. Re-insert the two bottom plate screws and secure. Remove Screws Belt Cover Guard 7

8 PRESTIGE PRO POWERHEAD Replacing the Belt To replace the belt, you must first remove the brush roller, see Removing the Brush Roller section on page 7. Belt 1. Locate and discard broken belt. To install new belt, locate the powerhead motor pulley and loop the belt around it. 2. Place the other end of the belt around the brush roller making sure the belt is seated in the belt groove of the brush roller. 3. Insert the brush roller back into the brush support and place the belt guard back into position. Place the metal bottom plate onto the powerhead by inserting the front end of the bottom plate first. Re-insert the two bottom plate screws and secure. 8

9 Replacing the Bulb Remove Screws 1. Turn the powerhead over and remove the bottom plate by first unscrewing the two bottom plate screws located by the rear wheels. 2. Remove the two top cover screws (located under the front wheels). Turn the powerhead back over, push the neck flat, and remove the top cover. 3. Simply pull the bulb out (DO NOT TWIST) and re-insert a factoryauthorized bulb. Place the top cover back on the unit, turn the powerhead over and re-insert the two top cover screws. Re-install the bottom plate by inserting the front end of the bottom plate first. Re-insert the two bottom plate screws and secure. 9

10 PRESTIGE PRO POWERHEAD LIMITED WARRANTY H-P Products, Inc. warrants that the Prestige Pro powerhead, when used for household purposes, pursuant to Seller s instructions, will be free from defects in materials and workmanship for a period of one (1) year from the date of the initial consumer purchase. H-P Products, Inc. warrants that the Prestige Pro powerhead, when used in a commercial application, pursuant to Seller s instructions will be free from defects in materials and workmanship for a period of ninety (90) days from the date of initial sale by H-P Products, Inc.. This warranty does not cover consumable parts such as light bulbs and replacement belts. This warranty is limited to the replacement of defective parts and any costs of shipping shall be incurred by the purchaser. THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS, IMPLIED OR STATUTORY AND H-P PRODUCTS, INC. SPECIFICALLY DISCLAIMS RESPONSIBILITY FOR CONSEQUENTIAL AND INCIDENTAL DAMAGES AND LIMITS THE IMPLIED WARRANTY OF MERCHANTABILITY TO THE PERIOD OF EFFECTIVENESS OF THIS EXPRESS WARRANTY. SERVICE INFORMATION The instructions in this booklet serves as a guide to routine maintenance. If additional service or repairs are required, please call for your nearest authorized servicing dealer. WARNING: ELECTRIC SHOCK COULD OCCUR IF USED ON WET SURFACES 10

11 11

12 512 W. Gorgas Street Louisville, Ohio