GTR 485 FUEL PUMP BASKET UPGRADE INSTALL GUIDE
|
|
- Herbert Casey
- 5 years ago
- Views:
Transcription
1 INTRODUCTION GTR 485 FUEL PUMP BASKET UPGRADE INSTALL GUIDE UPDATED Welcome to the Install Guide for the Visconti Tuning s GTR 485 FUEL PUMP BASKET UPGRADE. 485 pumps in our preassembled baskets now come with slim connectors that do not require any adapters. Important! When the gas gauge shows 1/2 your passenger side of the gas tank is 100% full, installation is best done when the car has less than half a tank of gas. Please also keep in mind this system was designed with the intention of having the fuel pumps fit very tight. Not using the provided LUBE will 100% tear the orings in the prefilter blocks. You will have problems if you bypass the fuel pump controller with a direct hardware kit that causes the primary pump to run at 14volts during idle. This will overrun the venturi pressure relief valve causing fuel pressure to creep 15-20PSI at idle. KIT CONTENTS Super Lube 1x Billet Basket Top 2x Pre-Filter Blocks with orings 1x 485 Filter Housing 1x Filter Housing Top with oring 2x Venturi jet fittings with orings 1x 10 micron filter 2x 40 micron pre-filters 6x Pump O-rings (4 Large, 2 Small) 3x 14mm bolts (Filter Housing Top) 2x 8mm bolts + Washers (Pre-Filter Block) 1x 30mm bolt (Fuel Pump Clamp) 1x 14mm bolt (Filter Housing Lock) 3/8 AN Quick Connect Fitting 1x Fuel Lines 1x Hose Clamp 1x Billet Barb Adapter for fuel hanger 1 P age
2 STEP 1 - REMOVE BACK SEAT AND GAS TANK COVER STEP 2 OPEN GAS CAP & DISCONNECT BOTH FUEL LINES FROM THE SENDING UNIT 2 P age
3 STEP 3 REMOVE SENDING UNIT & BASKET 3 P age
4 STEP 4 TAKE APART FACTORY BASKET 4 P age
5 STEP 5 PREPARE STOCK HANGER/SENDING UNIT STEP 5.1 Carefully remove the fuel pump ground from the top of the factory filter housing. They normally don t come out easy. STEP 5.2 Using a razor blade carefully remove the plastic fuel line that runs from the fuel hanger to the top of the STOCK fuel filter housing. STEP 5.3 Unscrew the provided billet barb adapter and apply lube to the (2) orings inside the fitting. LEAVE ORINGS INSIDE FITTING STEP 5.4 Firmly press the billet fitting on to the fuel hanger barb. STEP 5.5 Slide the two locks back onto the billet fitting and screw them together. This is best done while firmly pressing the fitting. STEP 5.6 Apply lube to the end of the billet fitting and push the provided hose on to the fitting. STEP 5.7 Once the provided fuel line is on fitted secure it using the provide fuel injection hose clamp. THIS DOES NOT NEED TO BE SUPER TIGHT DO NOT connect this fuel line to the billet basket until the basket is locked into the gas tank. 5 P age
6 STEP 6A ASSEMBLING THE BASKET (FOR SYSTEMS SOLD WITHOUT PUMPS) If you purchase your system with pumps please skip below to STEP 6B. If you purchased this system without fuel pumps PLEASE carefully follow these steps to properly install your fuel pumps. Not following these steps will result in damaging orings or fuel pumps. STEP 6A.1 Run the pump wires through the top of the basket top STEP 6A.2 Each pump is provided with two large and one small oring, install them into each port on the filter housing small oring goes in last. STEP 6A.2.1 Apply supplied lube on filter housing and pre-filter block orings STEP 6A.2.2 Install the first pump on the sort side of the filter housing. Place the two of provided O-rings in each port of the filter housing. STEP 6A.2.3- Before installing the pre-filter block on the back of the fuel pump you ll need to loosen the filter housing from the billet top. Not doing so will prevent you from lining up the bolt holes for the pre-filter block. Once both pre-filter blocks are secure tighten the filter housing until it is flush with the billet top. STEP 6A.3 - Slide the pre-filter block on to the back of the fuel pumps, secure using provided bolts and washers. STEP 6A.4 Install Fuel Pump Clamp DO NOT OVER TIGHEN!!!!!! STEP 6A.5 Install ONE-TIME-USE provided pre-filters, they don t just slide on, they require pressure I recommend bottoming out filter, then lock washer. STEP 6A.6 - Install Basket Ground Remove the pre-installed screw and place ground in the center of the basket top and turn ¼ of a turn. Secure the ground by reinstalling the screw. STEP 6A.7 Install OEM Pressure Relief 6 P age
7 STEP 6B ASSEMBLING THE BASKET (FOR SYSTEMS SOLD WITH PUMPS) If you purchased this system with fuel pumps then it will come preassembled. STEP 6B.1 Install ONE-TIME-USE provided pre-filters I recommend bottoming out filter, then lock washer. STEP 6B.2 Install Basket Ground Remove the pre-installed screw and place ground in the center of the basket top and turn ¼ of a turn. Secure the ground by reinstalling the screw. STEP 6B.3 Install OEM Pressure Relief STEP 7 CHECK FILTER HOUSING AN FITTING & TIPS Before installing the basket into the gas tank please make sure the preinstall 3/8 AN6 fitting in the filter housing is tight. There is no need to remove the fitting, simply make sure it is tight. A fitting that is loose or hand tight can cause extended cranking when trying to start the car. Although you ll be able to place this upgraded stock basket into the gas tank fully assembled you will not be able to connect any of the fuel lines until the is in the gas tank. 7 P age
8 We have cut open the side of the gas tank to show you how the unit looks when installed. Take notice how we run the fuel feed line. It s important to make sure none of the fuel lines interfere with the level sensor. We recommend looping the fuel feed line away from the fuel level (around the basket) If you have any questions or problems contact us via , not facebook or some thread on a fourm. john@vtune.us 8 P age
9 9 P age
INSTRUCTIONS. EZ-EFI FK In-Tank Fuel Kit
1 INSTRUCTIONS EZ-EFI 30401-FK In-Tank Fuel Kit Thank you for choosing FAST products; we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning installation,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL PUMP SLEEVE INSTALLATION KIT 2001-2006 BMW E46 M3 Document# 19-0058 Customer Support: info@radiumauto.com 1. There are 2 common ways to relieve fuel pressure on the BMW.
More informationEvo X Walbro 450 Pump System
Evo X Walbro 450 Pump System Installation Guide Please contact us at sales@wtftuned.com with any additional questions Tools required: 8 mm socket and wrench, needle-nose pliers, razor, drill w/ 5/64 bit,
More informationSKID MARK GARAGE. Axillary Fuel Supply
1 SKID MARK GARAGE Axillary Fuel Supply *Disclaimer: Our Axillary Fuel kits are designed to fit most late model GM vehicles with minimum modifications. While not quite a universal kit for all, it has been
More informationCut zip ties and remove 2 plastic wiring harness brackets.
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports
More informationGTR 12 INJECTOR CONVERSION INSTALL GUIDE
07/28/17 GTR 12 INJECTOR CONVERSION INSTALL GUIDE INTRODUCTION Welcome to the Install Guide for Visconti Tuning s Plug & Play GTR 12 Injector Conversion Kit. Your Conversion Kit should contain all of the
More informationDodge 24v ISB
1 BD KILLER B SINGLE TURBO KIT 1994-2002 Dodge 24v ISB Part #: 1045163 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION UNLESS AN EO# IS LISTED, THIS PRODUCT IS LEGAL IN CALIFORNIA FOR RACING VEHICLES
More informationProcedure: Installation of the ATP Eliminator Series turbo hardware kit for the 1.8T B5/B6 Audi A4/VW Passat Years 1996 through 2005.
ADVANCED TUNING PRODUCTS, INC Page 1 of 13 Procedure: Installation of the ATP Eliminator Series turbo hardware kit for the 1.8T B5/B6 Audi A4/VW Passat Years 1996 through 2005. Parts Checklist (Bill Of
More informationMercedes E63/CLS AMG Carbon Turbo Intake System Instructions
Mercedes E63/CLS AMG Carbon Turbo Intake System Instructions The goal of Alpha Performance is to provide the highest quality, best performing products available. By utilizing research and development,
More informationInstructions for Anti Shudder Valve Type EGR. Introduction
BMW EGR Valve Delete Instructions for Anti Shudder Valve Type EGR Introduction These instructions show how to install our BMW EGR Delete for EGRs fitted with an anti shudder valve, for all other elements
More informationBD 6.7L Super B Special Turbo Kit For L Dodge -- I n s t a l l a t i o n I n s t r u c t i o n s -- PN#
26 September 2012 1045140 6.7L Super B Special Turbo Installation 1 BD 6.7L Super B Special Turbo Kit For 2007.5-2012 6.7L Dodge -- I n s t a l l a t i o n I n s t r u c t i o n s -- PN# 1045140 PLEASE
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi (N55 engine) with BMW Standard bumper and with stock oil cooler
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0924 APPLICATION: 2011-12 E92 335i/xi (N55 engine) with BMW Standard bumper and with stock oil cooler Congratulations for being selective enough
More informationInstallation Instructions : Jaguar F-Type Intake System : Page 1
Installation Instructions : Jaguar F-Type Intake System : Page 1 1. Remove the undertray all the Torx bolts and the hex bolts holding the splitters in place need to be removed. 2. Starting with the right
More informationb o o s t r e t a i n e r v a l v e
b o o s t r e t a i n e r v a l v e i n s t a l l a t i o n i n s t r u c t i o n s For questions or tech support, CONTACT US! Email: greg@hiperformancestore.com sales@hpsimotorsports.com Sites: www.hiperformancestore-fiat.com
More informationBD 6.7L Super B Special Turbo Kit For L Dodge -- I n s t a l l a t i o n I n s t r u c t i o n s -- PN#
28 January 2014 1045140 6.7L Super B Special Turbo Installation (I-00266) 1 BD 6.7L Super B Special Turbo Kit For 2007.5-2012 6.7L Dodge -- I n s t a l l a t i o n I n s t r u c t i o n s -- PN# 1045140
More informationEngine Management System
Engine Management System 6 0 4-0 0 1 I N S T R U C T I O N S For 2005-2007 Harley-Davidson FL Models 2 Revolution Performance was founded with two major goals in mind to go that extra mile providing a
More informationFanatec GT3RS V1 to GT3RS V2 Tutorial
Fanatec GT3RS V1 to GT3RS V2 Tutorial by Roy Visser 1 How to update your Fanatec GT3RS V1 wheel to a GT3RS V2 wheel Welcome to this guided and detailed tutorial for upgrading your Fanatec GT3RS V1 wheel
More informationFUEL KITS P/N & 526-4
FUEL KITS P/N 526-3 & 526-4 NOTE: These instructions must be read and fully understood before beginning installation. If this manual is not fully understood, installation should not be attempted. Failure
More informationINSTALLATION INSTRUCTIONS
APPLICATIONS: 2000-`02 GP1200R; 1999-`00 XL1200Ltd.; 2001-`03 XLT1200 equipped with Riva Stinger2. NOTE: Stinger3 Upgrade Kit is compatible with Riva Stinger2 Exhaust System only. Do not attempt to install
More informationWRX/STI Engine Oil Cooler
2002-14 WRX/STI Engine Oil Cooler 2014-04-21 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of
More informationEngine Management System
Engine Management System 6 0 4-0 0 1 I N S T R U C T I O N S For 2005-2010 Harley-Davidson FXS (Softail) Models 2 Revolution Performance was founded with two major goals in mind to go that extra mile providing
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Part # 751-FP2500 IMPORTANT INFORMATION This Jagg oil cooler must be installed following these instructions. Read the easy-to-follow instructions fully prior to starting the installation
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Part # 751-FP2600 IMPORTANT INFORMATION This Jagg oil cooler must be installed following these instructions. Read the easy-to-follow instructions fully prior to starting the installation
More informationGrimmSpeed Install Guide Series Installing the GrimmSpeed WRX Boost Control Solenoid Updated 4/14/15
GrimmSpeed Install Guide Series Installing the GrimmSpeed 2015+ WRX Boost Control Solenoid Updated 4/14/15 Introduction: This guide will illustrate the installation of the GrimmSpeed 2015+ WRX Boost Control
More informationAPIKOL AAN INTAKE MANIFOLD INSTALLATION INSTRUCTIONS
APIKOL AAN INTAKE MANIFOLD INSTALLATION INSTRUCTIONS Estimated Installation Time: Approximately 2 hours Parts that will need to be modified/removed (Details provided later in the instructions): Intercooler
More informationINSTRUCTIONS. #82044 Race Diesel Nitrous System
INSTRUCTIONS #82044 Race Diesel Nitrous System Thank you for choosing ZEX products; we are proud to be your manufacturer of choice. Kit Parts List Description Qty. Description Qty. Nitrous Solenoid 2.088
More informationLethal Performance Dual FPDM Harness Kit Installation
Lethal Performance Dual FPDM Harness Kit Installation The Lethal Performance Dual FPDM Harness Kit is a plug-and-play modification. Depending on whether you are using the Lethal Performance wire upgrade
More information2015 WRX Engine Oil Cooler
2015 WRX Engine Oil Cooler 2014-04-24 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket
More informationAMS EVO X Fuel Pressure Regulator Kit
AMS EVO X Fuel Pressure Regulator Kit The goal of AMS is to provide the highest quality, best performing products available. By utilizing research and development, and rigorous testing programs AMS will
More informationTOP FEED FUEL RAIL KIT for WRX
TOP FEED FUEL RAIL KIT for 2002-14 WRX Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket
More informationCut zip ties and remove 2 plastic wiring harness brackets.
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. Included parts: 1 - New Bosch Cp3 Pump 1 - HSM Pulley 1 - Serpentine Belt 1 - Pump Bracket/
More informationBA /02/03/04/06/07/08/13/13B/15 BIG AIR KIT (BAK) - Yamaha Road Star (99-07)
BA-2020-00/02/03/04/06/07/08/13/13B/15 BIG AIR KIT (BAK) - Yamaha Road Star (99-07) Page: 1 Revision: 6.2-02/23/2011 Install Time: 1.5 Hours We recommend a qualified Yamaha technician install this kit
More informationL/6.7L DODGE CUMMINS
6/15/2016 #1050310D 2005-09 5.9/6.7 Dodge Cummins FlowMAX Lift Pump Kit (I-00170) - 1-2005-09 5.9L/6.7L DODGE CUMMINS BD FLOWMAX LIFT PUMP KIT Installation Instructions P/N # 1050310D PLEASE READ ALL INSTRUCTIONS
More information4L80E HD SHIFT RECALIBRATION KIT PART # 4L80ECC/HDSRK
4L80E HD SHIFT RECALIBRATION KIT PART # 4L80ECC/HDSRK Kit Contents: 1 Purple Pressure Regulator Spring 1 Orange Pressure Regulator Spring 1.375 Cup Plug 1 Separator Plate 1 Upper Valve Body Gasket 1 Lower
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0904 APPLICATION: 2011-2012 E90 335i/xi (N55 engine) with BMW standard bumper and with stock oil cooler Congratulations for being selective enough
More informationArrow Shark TS 760A E Starter for Gas Cars. Owner s Manual
Arrow Shark TS 760A E Starter for Gas Cars Starting a Gas Engine Has Never Been So Easy! Owner s Manual The TS 760A is heavy duty equipment with most main components being CNC billet finished and anodized
More informationINSTALLATION INSTRUCTIONS
1. Note: It is recommended this install be done with a minimal amount of fuel in the tank. This will reduce fuel spills and make installation easier and safer. Draining the tank is recommended. INSTALLATION
More informationINSTALLATION MANUAL APPLICATION: T D07 220G 16-18psi) T D07 260G 16-18psi) Cummins 5.9L /6.7L 24Valve Standard Pickup Truck
INSTALLATION MANUAL APPLICATION: T D07 220G (220GPH @ 16-18psi) T D07 260G (260GPH @ 16-18psi) Cummins 5.9L /6.7L 24Valve Standard Pickup Truck 2005-2016 1998.5-2004 *with In-tank Lift Pump* **Note: Cab
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL PUMP HANGER FORD MUSTANG: 2011+ S197 AND S550 Support: info@radiumauto.com Document# 19-0161 WARNING: DO NOT EXPOSE WORK AREA TO ANY SPARKS OR FIRE. DO NOT SMOKE WHILE WORKING
More informationTurboback Exhaust
501301 Turboback Exhaust 2014+ Ford Fiesta ST 501200 High Flow Catted Downpipe Page 2 501100 Catback Exhaust System Page 10 501200 High Flow Catted Downpipe 2014+ Ford Fiesta ST Congratulations on your
More informationInstant Chat off the main page of Or simply call our tech team at
02-07 WRX/STI Air Oil Separator for Top Mounted Intercooler Setups 2013-02- 27 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL PUMP HANGER MITSUBISHI LANCER EVOLUTION X Support: info@radiumauto.com Document# 19-0116 WARNING: DO NOT EXPOSE WORK AREA TO ANY SPARKS OR FIRE. DO NOT SMOKE WHILE WORKING
More informationAir Oil Separator for WRX
Air Oil Separator for 2015+ WRX 2018-06-05 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket
More informationEVOMS Cayenne TT V-Flow Installation Instructions
EVOMS Cayenne TT V-Flow Installation Instructions Passenger s Side OEM Air Box Removal: 1) Using a flat head screw driver, remove the plastic OEM engine covers by unscrewing the large plastic hold down
More informationSAGINAW P-SERIES PUMP INSTALLATION
SAGINAW P-SERIES PUMP INSTALLATION WARNING Failure to read and follow these instructions will void any warranty, can cause severe damage to power steering components and premature failure. Pump internals
More informationInstant Chat off the main page of Or simply call our tech team at
08+ Rotated Tuner Kit for Garrett GT Turbos 2016-11-03 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation
More informationAudi VW 2.0 TFSI T FSI Inlet Intake Manifold Swirl Flap Runner Delete Repair Kit Plate Blanks Install Instruction Guide
instructables Audi VW 2.0 TFSI T FSI Inlet Intake Manifold Swirl Flap Runner Delete Repair Kit Plate Blanks Install Instruction Guide by x8rltd Audi VW 2.0 TFSI T FSI Inlet Intake Manifold Swirl Flap Runner
More informationCOBB Tuning Catback Exhaust System MAZDASPEED3
572101 COBB Tuning Catback Exhaust System 2010+ MAZDASPEED3 Congratulations on your purchase of the COBB Tuning SS Catback Exhaust System for your 2010+ MAZDASPEED3. The following instructions will assist
More informationDODGE OFF ROAD T-STYLE STEERING KIT INSTALLATION INSTRUCTIONS
Dodge Off Road, LLC Specializing in Dodge Ram Solid-Axle 4x4 Suspension and Steering for Off Road Applications 855.9009.DOR sales@dodgeoffroad.com dodgeoffroad.com DODGE OFF ROAD T-STYLE STEERING KIT INSTALLATION
More informationINSTALLATION INSTRUCTIONS
APPLICATIONS: 2000-`02 GPR1200R; 1999-`00 XL1200Ltd.; 2001-`03 XLT1200 PARTS LISTING PART# QTY DESCRIPTION N/A 1 Stinger 3 Billet Flange N/A 1 Stinger 3 Head Pipe N/A 1 Stinger 2/3 Tail Pipe N/A 6 8MM
More informationGas Spreader PLUS Remote Kit With Built in Clutch Relay and On/Off Switch
Gas Spreader PLUS Remote Kit With Built in Clutch Relay and On/Off Switch NOTE: Read all directions first before continuing. This wireless controller kit has been programmed and tested before shipping.
More informationINSTRUCTIONS. #82028 Diesel Nitrous System. Thank you for choosing ZEX products; we are proud to be your manufacturer of choice.
1 INSTRUCTIONS #82028 Diesel Nitrous System Thank you for choosing ZEX products; we are proud to be your manufacturer of choice. Why our nitrous system is better: 2 Performance enthusiasts know the potential
More informationInstallation instructions for Camaro/Firebird and Nova* Windshield Wiper Systems
Installation instructions for 1967-69 Camaro/Firebird and 1968-74 Nova* Windshield Wiper Systems The Raingear 1967-69 Camaro/Firebird and 1964-74 Nova wiper system is designed for ease of installation
More informationThank you for purchasing the Dezod Motorsports Return Fuel System for your Scion tc.
Thank you for purchasing the Dezod Motorsports Return Fuel System for your Scion tc. We took much pride in putting together a fuel system that would deliver a maximum amount of fuel as simply as possible
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335is (N54 engine) with BMW M-Technic bumper and with stock oil cooler
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0923 APPLICATION: 2011 E92 335is (N54 engine) with BMW M-Technic bumper and with stock oil cooler Congratulations for being selective enough to
More informationADVANTAGE Annual Preventive Maintenance Instructions
ADVANTAGE Annual Preventive These instructions should be followed to perform preventive maintenance on the Advantage reprocessor. Before commencing work on the reprocessor, ensure that you have the appropriate
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL PUMP HANGER 08+ MITSUBISHI LANCER EVOLUTION X Support: info@radiumauto.com Document# 19-0116 WARNING: DO NOT EXPOSE WORK AREA TO ANY SPARKS OR FIRE. DO NOT SMOKE WHILE WORKING
More informationMAINTENANCE MANUAL DI 16
MAINTENANCE MANUAL DI 16 0.2-1.6% Press Ctrl + L for full screen 1 STANDARD INSTALLATION Inlet Outlet Optional accessories: Pressure regulator Solenoid valves Water meter Flow restrictor 200 Mesh/ 80 micron
More informationMain Fuel Tank #9662 Date 3/17/23 rev. 0. Pic #1 Pic #2. Pic #4. Pic #3. Pic #5 Pic #6
1045 S. Cherokee Lane Lodi CA 95240 Phone (209)400-7200 Fax (209)943-7923 www.wildhorses4x4.com Note: To assure a completely clean tank, use the large hole to inspect tank for any debris. It is highly
More informationTwoStep linkage. Installation guide Read this first. 2. Tools required for installation WARNING!
TwoStep linkage Installation guide HOT ROD CARBURETION CLOTHING & COLLECTIBLES SERVICE PARTS LINKAGE & FUEL DELIVERY If you need further information or assistance, please contact your Genuine Stromberg
More informationTURBO KIT INSTRUCTIONS
Revision 12/20/10 TURBO KIT INSTRUCTIONS This turbo kit consists of the necessary parts to upgrade or add a turbo to your 22R/RE/RET. This kit may require some fabrication to address your particular application
More informationONBOARD AIR HOOKUP KIT
ONBOARD AIR HOOKUP KIT PART NO. 20052 (30 amp - 110PSI on, 150PSI off) PART NO. 20053 (30 amp - 85PSI on, 105 PSI off) PART NO. 20055 (30 amp - 90 PSI on, 120 PSI off) IMPORTANT: It is essential that you
More informationSaab 9-3 Krona Downpipe Installation Instructions. What's Included:
www.kronaperformance.com 2003-2010 Saab 9-3 Krona Downpipe Installation Instructions What's Included: (1) 3 stainless downpipe (with or without catalyst) (1) 3-2.5 stainless downpipe adapter pipe (1) Turbo
More informationPlease read these instructions completely before proceeding with installation. Read all maintenance guidelines on page 7 before operating the vehicle.
MN-643 (02511) ECR 5461 Kit No. 39205 Please read these instructions completely before proceeding with installation Item P/N Description Quantity A 26391 Driver-Side Beam Assembly 1 B 26414 Passenger-Side
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS
COLD AIR INTAKE INSTALLATION INSTRUCTIONS # D760-0007 Fits: 2001-05 E46 325i NOTES: This intake MUST be used with the appropriate Dinan Performance Software for your vehicle. Evaluate & repair any stored
More informationTITAN Fuel Tanks. INSTALLATION INSTRUCTIONS G e n e r a t i o n V. Extended Capacity Replacement Tank for Diesel Chevrolet / GMC Trucks
Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended Capacity Replacement Tank
More informationMKVI Jetta Fog Light Kit
MKVI Jetta Fog Light Kit Part Number VW Jetta Fog Light Installation This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation
More informationPRODUCT: JK RockSport Steering Stabilizer Kit READ INSTRUCTIONS IN FULL BEFORE INSTALLATION. QUESTIONS? CALL M-F 7:00 AM 5:00 PM PST
PRODUCT: JK RockSport Steering Stabilizer Kit READ INSTRUCTIONS IN FULL BEFORE INSTALLATION. QUESTIONS? CALL 916-631-8071 M-F 7:00 AM 5:00 PM PST REV: A 07-14-2016 II-7133 The MetalCloak experience includes
More informationFor all Ram x4 Trucks, and all Ram x4 trucks.
Dodge Off Road, LLC Specializing in Dodge Ram Solid-Axle 4x4 Suspension and Steering for Off Road Applications 855.9009.DOR sales@dodgeoffroad.com dodgeoffroad.com DODGE OFF ROAD 5 th GEN STEERING KIT
More informationThermo-Bob 3 Installation Manual: KLR650E (2008 and newer)
Thermo-Bob 3 Installation Manual: KLR650E (2008 and newer) Thank you for purchasing the Thermo-Bob 3 radiator bypass system for the KLR650. Since the KLR already has a doohickey, it seemed that this thingamabob
More informationCVO - with ipod Amp & Speaker Upgrade Install Instructions for Batwing Fairing
CVO - with ipod Amp & Speaker Upgrade Install Instructions for Batwing Fairing Tools Needed: 1/2 inch Socket Wire Cutters 7/16 inch Socket Wire Strippers 5/16 inch Socket Phillips Screwdriver 1/2 inch
More informationPRO-CAMEL 24 SETUP AND OPERATING INSTRUCTIONS
PRO-CAMEL 24 SETUP AND OPERATING INSTRUCTIONS CAMEL MINING PRODUCTS Inc. P.O. Box 3179 Quartzsite AZ 85346 Telephones 1-800-331-5311 or 1-928-927-4009 FAX 1-928-927-4739 email desfox@tds.net ... DRIVE
More informationInstant Chat off the main page of Or simply call our tech team at
Subaru WRX/STI Air Oil Separator for Front Mounted Intercooler Setups 2013-02- 22 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons
More information82-01 Chevy S-10/ GMC Sonoma Front Kit Part No B
www.airliftcompany.com 82-01 Chevy S-10/ GMC Sonoma Front Kit Part No. 75512B MN-481 (02105) ECN 3549 Please read these instructions completely before proceeding with installation Left Side Upper Shock
More information4-Bank 6-POSition Chip. Vehicle Application
INSTALLATION Manual 4-Bank 6-POSition Chip Vehicle Application Part# F250-F350 7.3L 94-97 Automatic Transmission Ford Power Stroke 41611 F250-F350 7.3L 94-97 Standard Transmission Ford Power Stroke 41612
More informationCP3 Retrofit Pump Install:
CP3 Retrofit Pump Install: 2A 4 2 5 3 6 1.) Clean this area very well. No dirt = No troubles!!!!! Lay lots of Rags under and around the pumps, alternator and belts!!!!! This will save dropped tools, parts,
More informationInstallation Procedures
Installation Procedures Part Number for Audi B6 A4/S4 Audi B7 A4/S4 Audi C5 A6 Audi C6 A6 Heavy Duty Snub Mount Installation This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair
More informationRotated Tuner Kit for Garrett GT Turbos
Rotated Tuner Kit for Garrett GT Turbos 031411 Thank you for purchasing the PERRIN performance rotated turbo kit. Installation of this turbo should only be performed by persons experienced in the installation
More informationInstruction P/N:EVO1800
Q R S Instruction D EXPLODED VIEW A WARNING: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PRO- VIDED HARDWARE MAY DAMAGE THE INTAKE SYSTEM, ENGINE AND COMPONENTS!!! *Do not attempt to
More informationInstallation Instructions Diesel Nitrous System (#82028)
Installation Instructions Diesel Nitrous System (#82028) Thank you for choosing ZEX. If at any time you have questions regarding this or any of our products, please call our Nitrous Help support line at
More informationRACE X INTERCOOLER INSTALLATION INSTRUCTIONS
RACE X INTERCOOLER INSTALLATION INSTRUCTIONS The goal of AMS Performance is to provide the highest quality, best performing products available. By utilizing research and development, and rigorous testing
More informationRAM FRONT RADIUS ARM DROP BRACKETS Installation Instructions
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF SYNERGY MFG. ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF SYNERGY MFG IS PROHIBITIED. Revisions Rev. Description
More informationNissan GTR Alpha Fuel System
Nissan GTR Alpha Fuel System Instructions V5 The goal of AMS is to provide the highest quality, best performing products available. By utilizing research and development, and rigorous testing programs
More informationThermo-Bob 1 Installation Manual: Kawasaki Concours
Thermo-Bob 1 Installation Manual: 1986-2006 Kawasaki Concours This is a basic guide for installing the Thermo-Bob 1 on a Kawasaki ZG-1000 Concours. The bike used in the following photos was a 1995 year
More informationMINI TONG (LITTLE JERK 2) MODEL 8071
8071N02 REV 01 MINI TONG (LITTLE JERK 2) MODEL 8071 OPERATION, MAINTENANCE AND SAFETY MANUAL Reviewed and Approved By: Page 1 TABLE OF CONTENTS... PAGE 1. EQUIPMENT INFORMATION AND SPECIFICATION... 2 1.1
More informationPOLARIS XLT-SPECIAL TRIPLE PIPE SET P.N
1998-99 POLARIS XLT-SPECIAL TRIPLE PIPE SET P.N. 09-596 Important: Read instructions carefully before installation. 1-Remove stock exhaust, Y-pipe, and rear muffler support. 2-Install three exhaust flanges,
More informationMtd kit: Honda Engine Conversions for classic minis. mtd installation manual For Classic minis
Mtd kit: Honda Engine Conversions for classic minis mtd installation manual For Classic minis 1959 2001 Dear Customer, We welcome you to the Honda Powered Mini World. Thank you and Congratulations for
More informationTESLA MODEL S REFRESH FRONT FASCIA INSTALLATION MANUAL FIGURE 1. Unplugged Performance 3523 Jack Northrop Ave, Hawthorne, CA 90250
INSTALLATION MANUAL TESLA MODEL S PARTS QUANTITY INCLUDES FRONT FASCIA 1 PIECE V-STRIPE PANEL 1 PIECE HARDWARE KIT 1 SET PDC SENSOR HOLDERS 4 / 6 PIECES HOOD RELEASE KIT 1 KIT REFRESH FRONT FASCIA PLEASE
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS D Application: , E89 Z4 sdrive 35i without stock oil cooler* PARTS LIST
OIL COOLER KIT INSTALLATION INSTRUCTIONS D570-0891 Application: 2009-11, E89 Z4 sdrive 35i without stock oil cooler* PARTS LIST Qty Part No. Description 1 D573-0050 Oil Cooler + Frame Assy 1 D573-0044
More informationM7 R52S & R53 Cold Air Intake Installation Guide 53-3M7301
M7 R52S & R53 Cold Air Intake Installation Guide 53-3M7301 M7 Speed engineers and manufactures the highest quality MINI COOPER accessories and performance parts available anywhere on Planet Earth! Please
More informationSTEP 1 Disconnect the negative terminal from both batteries.
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports
More informationFord Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List:
2015-2017 Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List: LED Foglights/ Bezels 2 Flat head & Phillips screwdriver (if you ordered part#3600) Ratchet & Socket set OR Wiring harness
More informationP/N# Application Description Ford 6.0L Turbo Kit Only w/sct Tuner Ford 6.0L Turbo Kit Only (No drivability guarantee)
1 Low stall convertors are not recommended for this turbocharger kit. BD FORD 6.0L TURBOCHARGER KIT P/N# Application Description 1047070 2003-07 Ford 6.0L Turbo Kit Only w/sct Tuner 1047071 2003-07 Ford
More informationDodge/SRT Viper Gen IV and V (2008+) Intake Heat Shield
Dodge/SRT Viper Gen IV and V (2008+) Intake Heat Shield Overview: The DSE Intake Heat Shield reduces Intake Air Temperature (IAT) caused by a hot airbox assembly heating the incoming air. Ceramic coating
More informationWWW.RUSHRACINGPRODUCTS.COM 1. Remove the saddlebags, side covers, and seat; place them to the side. 2. Disconnect the battery. EXHAUST SYSTEM REMOVAL 3. Cover the primary housing and transmission covers
More informationTerms and conditions of use:
Terms and conditions of use: Berk Technology or any of its affiliates will not be held liable for any and all of the costs involved with use, installation, removal, inconvenience, or any other such associated
More informationINSTALLATION MANUAL. CUMMINS POWERED DODGE TRUCKS Model Year 1994 THROUGH High Performance Fuel System! With New Quick Connect Components!
#2 MODEL FP-100 & FP-150 INSTALLATION MANUAL CUMMINS POWERED DODGE TRUCKS Model Year 1994 THROUGH 1998 High Performance Fuel System! With New Quick Connect Components! READ INSTRUCTIONS THOROUGHLY BEFORE
More informationSymptom Diagnostics - Hard Start/No Start - Two-Filter System April Publication Number / Title Platform Section Title Change
1 4 05-15 SUBJECT DATE Symptom Diagnostics - Hard Start/No Start - Two-Filter System April 2015 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084
More informationINSTALLATION INSTRUCTIONS Dual Catch Can Kit Subaru Turbo and STi Document# Support:
INSTALLATION INSTRUCTIONS Dual Catch Can Kit 02-14 Subaru Turbo and 2015+ STi Document# 19-0099 Support: info@radiumauto.com This document covers the installation of a Radium dual catch can kit for the
More informationAir Oil Separator for WRX/STI Top Mounted Intercooler Setups
Air Oil Separator for 02-07 WRX/STI Top Mounted Intercooler Setups Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced
More information