NED s HYDRAULIC CLUTCH KIT PARTS LIST / INSTRUCTIONS
|
|
- Randolph Everett Hensley
- 6 years ago
- Views:
Transcription
1 NED s HYDRAULIC CLUTCH KIT PARTS LIST / INSTRUCTIONS Information collected and compiled by: Peter Goertz (Crazy Cunuc)
2 Prefix The intent of this document is ONLY meant to be a collaboration of ideas all in one place as a starting guide for anyone looking to do the conversion. All of the information used in this document was collected from various members from Kawasaki Triples Canada and I do not take credit for any of the ideas shared. THIS IS NOT AN OFFICIAL INSTRUCTION!! ALL OF THE FITTINGS ARE REFERENCED FROM RUSSELL PERFORMANCE PRODUCTS... LINKS INCLUDED IN DOCUMENT
3 1.0 PARTS LIST SLAVE CYLINDER NED s (Dave) Hydraulic Clutch Kit - Hose Fitting Thread Pitch: 10 X 1.25mm - Piston Travel (With Magura 9.5mm M/C): Seal: 7/8 Wheel Cylinder Cup Seal NAPA - PT# 3023 LINK: MASTER CYLINDER Magura: OEM Replacement Master Cylinder 9.5mm PT# Hose fitting Thread Pitch: 10 x 1.0mm - Magura Mirror Mount Bracket - PT# *BOTH AVAILABLE ON EBAY FLUID - Recommended: DOT 5 Silicone Fluid NOTE: - Magura Master Cylinder seals are NOT compatible with Glycol Based Fluid. - Since the Slave Cylinder cup seal is made for brake use it MAY NOT be compatible with Magura s Mineral Oil Blood and expand the rubber. SEALS - 10mm Parker Stat-o-Seals *Available on Ebay HOSE This is using all Russell Performance Parts. *This is only made as a quick reference guide for the Hose *Applications vary based on Bike Model, Handle bars, Gauges, Carbs etc etc RUSSELL Factory Assembled Universal Brake Hoses *Available in multiple finishes - Available in a variety of lengths (Check on your bike before ordering) LINK: FITTINGS *Available in multiple finishes This is using all Russell Performance Parts. *This is only made as a quick reference guide for the fittings
4 *Applications vary based on Bike Model, Handle bars, Gauges, Carbs etc etc SLAVE CYLINDER Fittings - Banjo Bolt 10mm x 1.25: PT# R40516C (Chrome Finish) - Banjo 45 : PT# R4055C (Chrome Finish) OR - Banjo 35 : PT# R4050C (Chrome Finish) LINK: MASTER CYLINDER Fittings *M/C to HOSE Thread Pitch 10mm x There have been TWO suggested methods (1) DIRECT HOSE TO M/C CONNECTION - Male Flare Union: PT# R41431 (2) BANJO APPLICATION - Banjo Bolt 10mm x 1.0: PT# R40506 (Chrome Finish) - Banjo 45 : PT# R4055C (Chrome Finish) OR - Banjo 35 : PT# R4050C (Chrome Finish) LINK:
5 2.0 INSTALLATION 2.1 SLAVE CYLINDER This is NOT meant as an OFFICIAL instruction but rather only a collaboration of tips/tricks from the various comments/members on the KTC forum. Piston should be greased upon assembly as there is no fluid contact to lubricate this in service. - Recommend very thick Silicone grease (compatible with rubber). Ex. Dow Corning 111. Labeled "Valve lubricant and Sealant" (for disk brake slider/pad tip lubrication). It does not wash off like other caliper greases. Ensure that Seal AND Piston are both orientated properly.
6 2.2 CLEARANCE / INTERFERENCE SLAVE TO ENGINE CASES When installing the slave, be sure that it seats properly. Some applications may have slight interference. It can be resolved quickly with a dermal. Luckily, it's between the mounting bolts so it's easy to feel the rocking (the shiny spot on the top where there is a ledge from machining). PERFECT FIT
7 PUSH ROD IF you are using a ball bearing pusher you may be required to trim down your push rod accordingly to make up for the added length from the ball bearing pusher. *BE CAUTIOUS AND ENSURE THAT ALL MEASUREMENTS ARE CORRECT BEFORE TRIMMING ENGINE COVER Based on your selected fitting application modification may be required to your LH Engine Sprocket Cover to accommodate the hydraulic clutch hose. *BE CAUTIOUS AND ENSURE THAT ALL MEASUREMENTS ARE CORRECT BEFORE CUTTING 2.3 MASTER CYLINDER / MIRROR MOUNT
8 2.4 FITTINGS Applications vary based on Bike Model, Handle bars, Gauges, Carbs etc. Refer to 1.0 PARTS LIST for all LINKS to RUSSELL PERFORMANCE PRODUCTS SLAVE CYLINDER RECOMENDATIONS - Banjo Bolt 10mm x 1.25: PT# R40516C (Chrome Finish) - Banjo 45 : PT# R4055C (Chrome Finish) OR - Banjo 35 : PT# R4050C (Chrome Finish)
9 MASTER CYLINDER RECOMMENDATIONS *M/C to HOSE Thread Pitch 10mm x 1.0 (1) DIRECT - HOSE TO M/C CONNECTION - Male Flare Union: PT# R41431 (2) BANJO APPLICATION Available Russell Banjo bolt is too long. If it is cut the chrome plating may have a burr and give troubles. *USE AT YOUR OWN RISK OR SOURCE A SHORTER BOLT - Banjo Bolt 10mm x 1.0: PT# R40506 (Chrome Finish) - Banjo 45 : PT# R4055C (Chrome Finish) OR - Banjo 35 : PT# R4050C (Chrome Finish)
10 2.5 HOSE RUSSELL Factory Assembled Universal Brake Hoses *Available in multiple Lengths & Finishes The Russell hose length is quoted tip to tip and there is no compensation for the additional length of the fittings. DETRMINING HOSE LENGTH Install the Master and Slave Cylinders with their respective fittings. Using a piece of 3/8 ID fuel hose; route and trim as needed with the hose plugged onto the threaded fittings. Remove the fuel hose and measure its final length. Use this value to determine the length of hose to order from Russell.
11 2.6 FINAL ASSEMBLY AND BLEEDING *Refer to 1.0 Parts List; Fluid, for correct recommendations. NOT ALL SEALS ARE COMPATIBLE WITH CERTAIN FLUIDS Assemble and install your Master Cylinder and fittings / hose. Leave the Slave Cylinder UNBOLTED from the Engine Cases. DO NOT bleed through the Slave Cylinder s bleed screw. Rather use it to fill the system via a syringe. Insure the line into the Master is LOWER than the ball end of the lever. Make sure there are no high spots in the line Hold the Slave Cylinder in one hand with a finger over the piston. Pump the Master Cylinder so the piston comes out of the Slave Cylinder 0.125" Slowly push the piston back into the bore. *DO NOT push it all the way in; Seal damage CAN occur from being pushed past the ports! The DOT 5 fluid likes to froth. GO SLOWLY! Repeat until all the air is out.
INSTALLATION GUIDE. RMS500, RMS501, RMS502, RMS503, RMS506, RMS507, RMS508, RMS509, -OR Manual Revision:
REKLUSE MOTOR SPORTS z-start Brake Kit INSTALLATION GUIDE RMS500, RMS501, RMS502, RMS503, RMS506, RMS507, RMS508, RMS509, -OR 196-200 Manual Revision: 051309 2009 Rekluse Motor Sports Rekluse Motor Sports,
More informationTorque specifications Stainless steel ft. lbs Aluminum ft. lbs
INSTALLATION PROCESS: FK003D802-8 Complete Brake Line Kit 2013 Kawasaki VN1700 Voyager Custom ABS 2013 Kawasaki VN1700 Vaquero ABS Torque specifications Stainless steel 15-17 ft. lbs Aluminum 12-15 ft.
More informationINSTALLATION PROCESS: FK003D771-9 Complete Brake Line Kit 2012 Yamaha XT 1200Z Super Tenere
INSTALLATION PROCESS: FK003D771-9 Complete Brake Line Kit 2012 Yamaha XT 1200Z Super Tenere Step 1: Identify the key components that complete our brake line kit: You should have nine (9) lines, one (1)
More informationINSTALLATION GUIDE. RMS510, 511, 512, 513, 511MC 510-OR, 512-OR Manual Revision:
REKLUSE MOTOR SPORTS z-start Dual-Actuated Brake Kit INSTALLATION GUIDE RMS510, 511, 512, 513, 511MC 510-OR, 512-OR 196-210 Manual Revision: 051309 2002-2009 Rekluse Motor Sports Rekluse Motor Sports,
More informationTSS Fit Kit Installation Instructions Timbersled Snow Bike System
TSS Fit Kit Installation Instructions Timbersled Snow Bike System Information needed before you start: Read the entire installation instructions before starting. The instruction sheet is universal for
More informationw w w. h d o n l i n e s h o p. d e MODULAR DIAMONDBACK BRAKE LINE KITS GENERAL -J04284 REV Kit Number Models Tools and Supplies Required
-J08 REV. 007-07-6 GENERAL MODULAR DIAMONDBACK BRAKE LINE KITS Table. Upper Brake Line s (Banjo Angle 0 - Straight) 7-07 77-07 79-07 8-07 87-07 9-07 8-07 8 inch 9 inch 0 inch inch inch inch inch 96-07
More informationINSTALLATION PROCESS: FK003D744 Complete Brake Line Kit VFR800 NON ABS
INSTALLATION PROCESS: FK003D744 Complete Brake Line Kit 2000-2007 VFR800 NON ABS Step 1: Identify the key components that complete our brake line kit: You should have Ten (10) hoses, one (1) double banjo
More informationINSTALLATION & USER S GUIDE
REKLUSE MOTOR SPORTS The Rekluse Left Hand Rear Brake Kit INSTALLATION TIPS INSTALLATION & USER S GUIDE Doc ID: 196-5301 Doc Rev: 031016 Before continuing, we recommend watching the Brake Kit Installation
More informationTorque specifications Stainless steel ft. lbs Aluminum ft. lbs
INSTALLATION PROCESS: FK003D738C Front and Rear Brake Line Kit 2009-2012 BMW S1000 RR ABS Torque specifications Stainless steel 15-17 ft. lbs Aluminum 12-15 ft. lbs Step 1: Identify the key components
More information55-64 Full Size GM (Impala, Bel Air, etc.) This kit is for axles with a 3 3/8 spread center to center on the top two bolt holes (pictured left).
SUM-BK1624A Full Size GM Installation Instructions Rear Disc Conversion 55-64 Full Size GM (Impala, Bel Air, etc.) This kit is for axles with a 3 3/8 spread center to center on the top two bolt holes (pictured
More informationA /F/X Body Instruction Packet Rear Disc Conversion
A /F/X Body Instruction Packet Rear Disc Conversion 64-72 A Body / 67-81 F Body / 62-74 X Body This kit is for axles with a 3 1/8 spread center to center on the top two bolt holes (pictured left). Rotor
More informationInstallation Instructions
Installation Instructions Rear Disc Brake Conversion Kit Item # RC4001, RC4001X Applications: Mopar 7.25, 8.25, 9.25 Axles Thank you for choosing Leed Brakes for your automotive product needs. Before you
More informationMASTER CYLINDER INSPECTION
7-16 CHASSIS A-PDF Split DEMO : Purchase from www.a-pdf.com to remove the watermark Remove the piston assembly. MASTER CYLINDER INSPECTION MASTER CYLINDER Inspect the master cylinder bore for any scratches
More informationOVERHAULING BRAKE CALIPERS GUIDE by Mr. Stefnwolf. This guide is for a 1982 GSX750ET but I expect most of the GS series to be similar if not the same.
OVERHAULING BRAKE CALIPERS GUIDE by Mr. Stefnwolf This guide is for a 1982 GSX750ET but I expect most of the GS series to be similar if not the same. Badly corroded calipers (caused by moisture in the
More informationINSTALLATION & USER S GUIDE
REKLUSE MOTOR SPORTS The Rekluse Core EXP Kit with Adjustable Slave Cylinder INSTALLATION & USER S GUIDE Doc ID: 191-7704A Doc Rev: 102915 OVERVIEW This kit replaces the OEM core clutch components including
More informationInstallation Instructions
Installation Instructions Rear Disc Brake Conversion Kit Item # RC2001, RC2001X Applications: Mopar 8-3/4 & 9-3/4 Rear Axles Thank you for choosing Leed Brakes for your automotive product needs. Before
More informationINSTALLATION PROCESS: FK003D945-7 Complete Front, Rear, and Clutch A.B.S. KIT Harley Davidson FLH Touring Models
INSTALLATION PROCESS: FK003D945-7 Complete Front, Rear, and Clutch A.B.S. KIT 2014-2017 Harley Davidson FLH Touring Models Parts List: 4 Lines 1 Brake Light Switch Adapter 7 Single banjo bolts 2 Caliper
More informationUNRESPONSIVE CLUTCH: AIR ENTRAPPED IN HYDRAULIC SYS Ford Ra... UNRESPONSIVE CLUTCH: AIR ENTRAPPED IN HYDRAULIC SYS TECHNICAL SERVICE BULLETIN
Page 1 of 5 UNRESPONSIVE CLUTCH: AIR ENTRAPPED IN HYDRAULIC SYS TECHNICAL SERVICE BULLETIN Reference Number(s): 93-12-19, Date of Issue: June 9, 1993 CONDITIONS CLUTCH - "SOFT" UNRESPONSIVE CLUTCH PEDAL
More informationInstallation Instructions
Installation Instructions Rear Disc Brake Conversion Kit Item # RC1001, RC1001X Applications: 64-72 A-body, 67 F-Body, 63-67 X-body with Non Staggered Shocks Thank you for choosing GPS Auto for your automotive
More informationHAYS HYDRAULIC RELEASE BEARING INSTALLATION INSTRUCTIONS
HAYS HYDRAULIC RELEASE BEARING INSTALLATION INSTRUCTIONS PRELIMINARY INSTALLATION NOTES IMPORTANT! DO NOT RETURN THIS PRODUCT TO YOUR DISTRIBUTOR. If you have questions, please review additional information
More informationTorque specifications Stainless steel ft. lbs Aluminum ft. lbs
INSTALLATION PROCESS: FK003D926-R Rear Brake Line Kit 2017 + SUZUKI GSX-R 1000 Torque specifications Stainless steel 15-17 ft. lbs Aluminum 12-15 ft. lbs Step 1: Identify the key components that complete
More informationleft-side-drive hydraulic side cover installation manual
left-side-drive hydraulic side cover installation manual rear feed and front feed models rear feed front feed for baker OD6, dd5, dd6, and stock H-D 5-speeds v3-021307 DD5, DD6, and Stock H-D Instructions
More informationMopar 8 3/4 & 9 3/4 (Dana) Installation Instructions Rear Disc Conversion
Mopar 8 3/4 & 9 3/4 (Dana) Installation Instructions Rear Disc Conversion This kit is for either Mopar 8 ¾ or Mopar 9 ¾ (Dana). This kit is designed to work with axles with either GM 5 x 4.75 Bolt Pattern
More informationCLUTCH SECTION CL CONTENTS C TRANSMISSION/TRANSAXLE CL-1
CLUTCH C TRANSMISSION/TRANSAXLE SECTION CL A B CLUTCH CL D CONTENTS E PRECAUTIONS... 2 Caution... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools... 3 NOISE, VIBRATION AND HARSHNESS
More informationBRAKE PADS REPLACEMENT
KLR650 Homepage Contact Me You must remove the "REMOVE-THIS" in my email address for it to work. This is a hobby website dedicated to the Kawasaki KLR650 motorcycle. I make no claim concerning the accuracy
More informationTools, Equipment and Supplies Needed:
153-162 DISC BRAKE/DUAL MASTER CYLINDER CONVERSION Please take the time to read the enclosed instructions carefully. If you have any questions, call our Product Assistance personnel for clarifi cation.
More informationFull Size GM Installation Instructions
Full Size GM Installation Instructions Rear Disc Conversion 55 64 Full Size GM (Impala, Bel Air, etc.) This kit is for axle with a 3 3/8 spread center to center on the top two bolt holes (pictured left).
More informationGSX-R1000 K7/K8 Front master cylinder replacement procedure
GSX-R000 K7/K8 Front master cylinder replacement procedure.preparation Replacement parts Part name P/NO Q ty Description Cylinder kit, FR MASTER 59000-080-RX0 Master cylinder set (5960-7H0) Bracket, reservoir
More informationpowered with magura.com
powered with magura.com HCT Hard Core Technology the new patented technology from MAGURA improves the feedback from your brake system. Originally designed for the race track the benefits are just as relevant
More informationREAR DRUM BRAKE (1ZZ FE(FF))
REAR DRUM BRAKE (1ZZFE(FF)) OVERHAUL HINT: Overhaul the RH side by the same procedures as LH side. 1. REMOVE REAR WHEEL 2. DRAIN BRAKE FLUID NOTICE: Wash the brake fluid off immediately if it comes into
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FOR A136 REAR DRUM TO DISC BRAKE CONVERSION KIT for 1970-75 Jeep, CJ SERIES with Dana 44 flanged axle Thank you for choosing STAINLESS STEEL BRAKES CORPORATION
More information67-69 Camaro. Hydraulic Clutch Master Cylinder Installation Instructions Read These Instructions Completely Before Beginning
67-69 Camaro Hydraulic Clutch Master Cylinder Installation Instructions Read These Instructions Completely Before Beginning These instructions are for hydraulic master cylinder installations using an external
More informationCHASSIS CONTENTS EXTERIOR PARTS 7-1 FRONT WHEEL 7-2 FRONT BRAKE 7-6 HANDLEBARS 7-13 FRONT FORK 7-15 STEERING 7-23 REAR WHEEL 7-26 REAR BRAKE 7-30
CHASSIS CONTENTS EXTERIOR PARTS 7- FRONT WHEEL 7-2 FRONT BRAKE 7-6 HANDLEBARS 7-3 FRONT FORK 7-5 STEERING 7-23 REAR WHEEL 7-26 REAR BRAKE 7-30 REAR SHOCK ABSORBER 7-32 SWING ARM 7-33 7 7- CHASSIS EXTERIOR
More informationDISC BRAKE/DUAL MASTER CYLINDER CONVERSION. Tools, Equipment and Supplies Needed:
Please take the time to read the enclosed instructions carefully. If you have any questions, call our Product Assistance personnel for clarification. It is important to note that these instructions contain
More informationHydraulic Brakes: How and Why
Hydraulic Brakes: How and Why Hydraulic disc brakes have been fitted to Moto Guzzi for over forty years, and yet a surprisingly large number of people don't properly understand how they work. The disc
More informationGM FULL SIZE REAR DISC BRAKE KIT
GM FULL SIZE REAR DISC BRAKE KIT This kit is for axles with a 3 3/8 spread center to center on the top two bolt holes (pictured left). If your axle flange measures 3 1/8 from center to center, you need
More informationCHASSIS CONTENTS EXTERIOR PARTS 6-1 FRONT WHEEL 6-2 FRONT BRAKE 6-6 HANDLEBARS 6-12 REAR WHEEL 6-30 REAR BRAKE 6-34 REAR SHOCK ABSORBER 6-36
CHASSIS CONTENTS EXTERIOR PARTS 6-1 FRONT WHEEL 6-2 FRONT BRAKE 6-6 HANDLEBARS 6-12 FRONT FORK ( ) 6-14 FRONT FORK ( ) 6-20 STEERING 6-27 REAR WHEEL 6-30 REAR BRAKE 6-34 REAR SHOCK ABSORBER 6-36 6 SWING
More information1993 AEROSTAR, BRONCO, EXPLORER, F SERIES, F-47, RANGER
CLUTCH SOFT UNRESPONSIVE CLUTCH Article No. PEDAL AIR ENTRAPPED IN HYDRAULIC 93-12-19 SYSTEM SERVICE TIPS CLUTCH HYDRAULIC UNABLE TO RELEASE AIR ENTRAPPED IN SYSTEM SERVICE TIPS CLUTCH HYDRAULIC BLEED
More informationInstallation Manual. Model T675A Engine Brakes. For Mack 6 Cylinder, 2 valve Head ENDT-673, 675, 676 & E6 Series Engines.
Engine Brakes Installation Manual Model T675A Engine Brakes For Mack 6 Cylinder, 2 valve Head ENDT-673, 675, 676 & E6 Series Engines TecBrake P.O. Box 27822 Houston, Texas 77227 INSTALLATION MANUAL TECBRAKE
More informationThis chapter covers the location and servicing of the front brake components for the KYMCO MXU 700i and MXU 500i models.
KYMCO MXU 500i/700i Repair Manual Brake System 9.Brake System This chapter covers the location and servicing of the front brake components for the KYMCO MXU 700i and MXU 500i models. 1.Brake Discs... 9-3
More informationHYMEC. Owner's manual
HYMEC Owner's manual Contents Abbildungen Introduction Preface... 6 Legend...6 Technical specifications overview...7 Safety Intended use... 8 Basic safety instructions... 8 Installation Installing the
More informationCLUTCH PREPARATION Union Nut Wrench 10 mm Clutch Guide Tool Input Shaft Front Bearing Puller
CLUTCH CL1 CL2 PREPARATION SST (SPECIAL SERVICE TOOLS) CLUTCH PREPARATION 0902300100 Union Nut Wrench 10 mm Clutch line 0930100110 Clutch Guide Tool 0930335011 Input Shaft Front Bearing Puller 0930430012
More informationMASTER CYLINDER MC9601
MASTER CYLINDER MC9601 1 CHECK...1 2 INSTALLATION...1 3 CHECK LINE POSITIONING...2 4 SET UP...2 5 BLEEDING OPERATIONS...3 6 MC013/AC004 BRAKE SWITCH...5 7 KR0091 LEVER...6 8 KR0119 BLEEDER SCREW+RUBBER...7
More informationMOUNTAIN HORSE INSTALL KIT
MOUNTAIN HORSE INSTALL KIT P/N 9928508 APPLICATION Installation Instructions are for all Mountain Horse TSS and TFS Installation Kits and Timbersled Mountain Horse chassis installations. The Timbersled
More informationM-2300-T 6-Piston Mustang Brake Kit INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationFull Size GM Installation Instructions Rear Disc Conversion
Full Size GM Installation Instructions Rear Disc Conversion 65 68 Full Size GM (Impala, Bel Air, etc.) This kit is for axles with a 3 3/8 spread center to center on the top two bolt holes (pictured left).
More informationM-2300-M Mustang GT Rear Disc Brake Bracket Kit INSTALLATION INSTRUCTIONS
Please contact the Tech Line for the most current instruction information (800) 367-3788!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! INTRODUCTION: This kit allows for the
More informationSTEP 1 Clutch Slave Cylinder Piston Removal and Installation
STEP 1 Clutch Slave Cylinder Piston Removal and Installation This step is mandatory as the Clutch Adjustment Screw will remain bolted in place and you will not be able to remove the Primary Drive Cover
More informationREMOVAL AND INSTALLATION
308-02B-1 REMOVAL AND INSTALLATION 308-02B-1 Clutch Master Cylinder Material Item Brake Fluid (DOT 3) Specification ESA-M6C25-A Removal WARNING: Brake fluid contains polyglycol ethers and polyglycols.
More informationBrake Upgrade Kit Fitting Instructions Bonneville America
WARNING: Always have Triumph approved parts, accessories and conversions fitted by a trained technician of an authorised Triumph Dealer. The fitment of parts, accessories and conversions by a technician
More informationModel DFR 070/156/220 Rotary Actuator
Figure 1 DFR 156 TABLE OF CONTENTS General 2 Actuator Assembly 18 Scope 2 Bushing / Yoke Assembly 18 Principles of Operation 2 Spring Barrel Assembly 18 Safety Caution 2 Diaphragm Plate Assembly 20 Specifications
More informationFord 8, 9 Small Bearing Installation Instructions Rear Disc Conversion
Ford 8, 9 Small Bearing Installation Instructions Rear Disc Conversion This kit is for Ford 9 rear axles with the small (2.835 ) style bearing and Ford 8 rear ends. This kit is designed to work with axles
More informationCHASSIS CONTENTS FRONT WHEEL 6-1 FRONT BRAKE 6-6 FRONT FORK 6-14 STEERING STEM 6-20 REAR WHEEL AND REAR BRAKE 6-25 SUSPENSION 6-31 REAR SWING ARM 6-36
CHASSIS CONTENTS FRONT WHEEL 6-1 FRONT BRAKE 6-6 FRONT FORK 6-14 STEERING STEM 6-20 REAR WHEEL AND REAR BRAKE 6-25 SUSPENSION 6-31 REAR SWING ARM 6-36 6 6-1 CHASSIS FRONT WHEEL REMOVAL Support the machine
More informationENG CLUTCH CLUTCH RELEASE CYLINDER. Order Job/Part Q ty Remarks. Removing the clutch release cylinder. Remove the parts in the order listed.
EAS00 CLUTCH RELEASE CYLINDER 0 Nm (.0 m kg) 0 Nm (.0 m kg) Order Job/Part Q ty Remarks Removing the clutch release cylinder Bolt Remove the parts in the order listed. Refer to INSTALLING THE CLUTCH RELEASE
More informationALLDATA Online Saturn L200 L4-2.2L VIN F - Base Brake Bleeding. Base Brake Bleeding
Page 1 of 9 Base Brake Bleeding BASE BRAKE BLEEDING TOOLS REQUIRED J-439l5 Brake Bleed Adapter J29532 Pressure Bleeder MANUAL BLEEDING NOTICE: Brake fluid is corrosive to painted surfaces. Take care not
More informationSERVICE PROCEDURES FOR CLUTCH HYDRAULIC UNITS
SERVICE PROCEDURES FOR CLUTCH HYDRAULIC UNITS SAFETY PROCEDURES Always follow the vehicle manufacturer's recommended safety procedures in your Shop and Owners Manual. REQUIRED TOOLS Flat blade screwdriver,
More informationA /F/X Body Instruction Packet Rear Disc Conversion
A /F/X Body Instruction Packet Rear Disc Conversion 64-72 A Body / 67-81 F Body / 62-74 X Body This kit is for axles with a 3 1/8 spread center to center on the top two bolt holes (pictured left). If your
More informationParking brake Mechanical brake acting on rear wheels
11 Brake System 11.1 General SPECIFICATIONS EJTC0010 Master cylinder Type Tandem type I.D. mm(in.) 20.64 mm (0.813 in.) Fluid level warning sensor Provided Brake booster Type Vacuum Boosting ratio 4.0
More informationINSTALLATION PROCESS: FK003D932-6 FRONT & REAR A.B.S. KIT 2017 Harley Davidson FXDL Lowrider S ABS
INSTALLATION PROCESS: FK003D932-6 FRONT & REAR A.B.S. KIT 2017 Harley Davidson FXDL Lowrider S ABS Parts List: 6 Lines 1 Splitter Block 4 A.B.S. Block Bolts (KIT A) 1 1x1/4 x20x1 Bolt 4 Caliper/Front Master
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A128-4 1997-2004 JEEP WRANGLER (TJ) WITH DANA 44 AXLES (non-abs) Thank you for choosing STAINLESS STEEL BRAKES for your braking needs. Pleases take the
More informationSignature Series A/F/X Body GM Installation Instructions Rear Disc Conversion
Signature Series A/F/X Body GM Installation Instructions Rear Disc Conversion 64-72 A Body / 67-81 F Body / 62-74 X Body This kit is for axles with a 3 1/8 spread center to center on the top two bolt holes
More informationHCT ERSPORTS HNOLOGY THE RADIAL FAMILY MAGURA.COM
EN HCT THE RADIAL FAMILY TECHNOT POWERSP HNOLOGY ERSPORTS MAGURA.COM HCT BRAKE AND CLUTCH HARD CORE TECHNOLOGY LIKE A PRO The new patented MAGURA technology significantly improves the responsiveness of
More informationINSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE CROSS COUNTRY / CROSS ROADS / HARD BALL RAKE KIT
INSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE CROSS COUNTRY / CROSS ROADS / HARD BALL RAKE KIT Thank you for choosing the Motor Trike Cross Country / Cross Roads / Hard Ball rake kit. We ask that you read
More informationHKS 700E. Service Manual June Ver. 2.04
HKS 700E Service Manual 009 June Ver..04 HKS CO.,LTD 78 KITAYAMA FUJINOMIYA SHIZUOKA JAPAN 48-09 TEL +8(0)544-54-78 FAX +8(0)544-54-40 hks_aviation@hks-power.co.jp http://www.hks-power.co.jp/hks_aviation/
More informationSlave Cylinder Weep Hole Drilling Procedure
Slave Cylinder Weep Hole Drilling Procedure Tools Required: T20 Torx Driver T25 Torx Driver T25 Torx Bit with ¼ Ratchet Wrench 4mm Hex Key (Allen wrench) 5mm Hex Key 6mm Hex Key 8mm Hex Key 12mm Hex Key
More informationDura Force Disc Brake System Service Manual
TS 20809_a 3501 Shotwell Drive ISO/TS 16949:2002 Registered (PH): 937.743.8125 Franklin, OH 45005 www.waltheremc.com (FX): 937.743.8232 Table of Contents General Description 1 3 Fastener Torque Chart 4
More informationOVERHAUL. Remove the union bolt and a gasket from the disc brake cylinder, then disconnect the flexible hose from the disc brake cylinder.
OVERHAUL COMPONENTS: See page 3232 Overhaul the RH side by the same procedures with LH side. Two types of brake pad exist; one is with slit and the other without slit. 1. REMOVE REAR WHEEL 2. DRAIN FLUID
More informationCLUTCH SECTION CL CONTENTS C TRANSMISSION/TRANSAXLE CL-1
CLUTCH C TRANSMISSION/TRANSAXLE SECTION CL A B CLUTCH CL D CONTENTS E PRECAUTIONS... 2 Caution... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools... 3 NOISE, VIBRATION AND HARSHNESS
More informationA /F/X Body Instruction Packet Rear Disc Conversion
A /F/X Body Instruction Packet Rear Disc Conversion 64-72 A Body / 67-81 F Body / 62-74 X Body This kit is for axles with a 3 1/8 spread center to center on the top two bolt holes (pictured left). If your
More information1999 Toyota RAV BRAKES Disc & Drum - Trucks & Vans
DESCRIPTION & OPERATION 1999-2000 BRAKES Disc & Drum - Trucks & Vans WARNING: For warnings and procedures regarding vehicles equipped with Anti-Lock Brake Systems (ABS), see appropriate ANTI-LOCK article.
More informationBRAKE SYSTEM Return To Main Table of Contents
BRAKE SYSTEM Return To Main Table of Contents GENERAL... 2 BRAKE PEDAL... 10 MASTER CYLINDER... 13 BRAKE BOOSTER... 16 BRAKE LINE... 18 PROPORTIONING VALVE... 19 FRONT DISC BRAKE... 20 REAR DRUM BRAKE...
More informationINSTALLATION & USER S GUIDE
INSTALLATION & USER S GUIDE RadiusCX Clutch For KTM/Husqvarna DDS clutches Doc ID: 191-7901A Revision: 050217 2017 Rekluse Motor Sports Rekluse Motor Sports, Inc. support@rekluse.com TABLE OF CONTENTS
More informationASSEMBLY INSTRUCTIONS FOR DYNAPRO BIG BRAKE FRONT HAT KIT, WITH DIAMETER VENTED ROTOR - RACE
www.wilwood.com ASSEMBLY INSTRUCTIONS FOR DYNAPRO BIG BRAKE FRONT HAT KIT, WITH 11.75 DIAMETER VENTED ROTOR - RACE 00 - PRESENT BMW MINI COOPER AND MINI COOPER S PART NUMBER GROUP 10-870 DISC BRAKES SHOULD
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS FOR SUPERLITE 6 BIG BRAKE FRONT HAT KIT PRO STREET APPLICATION,.90 DIAMETER VENTED ROTOR 99-00 MUSTANG (5 LUG, STOCK OFFSET) PART NUMBER GROUP 0-907 INSTALLATION OF THIS KIT SHOULD
More informationASSEMBLY INSTRUCTIONS FOR PRO-MATRIX OE UPGRADE PAD AND ROTOR KIT REAR, WITH DIAMETER VENTED ROTOR CHEVROLET C-4 CORVETTE
ASSEMBLY INSTRUCTIONS FOR PRO-MATRIX OE UPGRADE PAD AND ROTOR KIT REAR, WITH 1.00 DIAMETER VENTED ROTOR 1988-1996 CHEVROLET C-4 CORVETTE PART NUMBER GROUP 140-8314 DISC BRAKES SHOULD ONLY BE INSTALLED
More information2010+ Victory Cross Country / Cross Roads Installation Guide Nov 2014
2010+ Victory Cross Country / Cross Roads Installation Guide Nov 2014 125 Industrial Drive Spearfish, SD 57783 Toll Free 888.3WHEELS w w w. l e h m a n t r i k e s. c o m UNDERSTANDING SAFETY LABELS &
More informationSCION tc BIG BRAKE KIT Section I - Installation Preparation
SCION tc 2005- BIG BRAKE KIT Section I - Installation Preparation Part Number: PTR09-21080 Kit Contents Item # Quantity Reqd. Description 1 1 Brake Rotor, LH Front 2 1 Brake Rotor, RH Front 3 1 Brake Caliper
More informationGENERAL PROCEDURES. Component Bleeding. Master Cylinder Priming In-Vehicle or Bench
206-00-1 Brake System General Information 206-00-1 GENERAL PROCEDURES Component Bleeding Special Tool(s) Worldwide Diagnostic System (WDS) 418-F224, New Generation STAR (NGS) Tester 418-F052, or equivalent
More informationSlide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided.
Slide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided. Put the urethane bushings into the upper antiroll-bar-link eyebolt. Coat the bushings
More informationHydraulic Hand Pallet Trucks
Operating Instructions & Parts Manual 12U124 Please read and save these instructions. Read carefully before attempting to assemble, install, operate, or maintain the product described. Protect yourself
More informationDBK FULL-SIZE CHEVY DISC BRAKE conversion KIT
DBK5964 1959-1964 FULL-SIZE CHEVY DISC BRAKE conversion KIT impala, bel air, biscayne Installation Instructions does not fit 14" rims must ust 15" or larger for this kit to be installed correctly on your
More information06-11 Civic Si / EM1 Clutch Master Cylinder
06-11 Civic Si / EM1 Clutch Master Cylinder Upgrade This guide will show you how to install the EM1 CMC upgrade kit in a 2006-2011 Honda Civic Si. Written By: Hybrid Racing 2017 guides.hybrid-racing.com/
More information2012 MKT Workshop Manual. REMOVAL AND INSTALLATION Procedure revision date: 06/13/2011
SECTION 205-05: Rear Drive Halfshafts REMOVAL AND INSTALLATION Procedure revision date: 06/13/2011 Halfshaft Special Tool(s) Axle Seal Protector 205-816 Front Hub Remover 205-D070 (D93P-1175-B) or equivalent
More informationSECTION 35iS/U: LANDING GEAR & ENGINE MOUNT
WD-1221 ENGINE MOUNT STANDOFF SECTION 35iS/U: LANDING GEAR & ENGINE MOUNT U-01203E-1 INBOARD DOUBLER PLATE U-01203B-1 INBOARD WEAR PLATE U-01203C-1 BEARING PLATE U-01203-2 (U-01203-1 SHOWN) INBOARD MAIN
More information16. BRAKE SYSTEM 16-0 BRAKE SYSTEM UXV 500
16 BRAKE SYSTEM 16 SERVICE INFORMATION------------------------------------------------ 16-1 TROUBLESHOOTING----------------------------------------------------- 16-2 BRAKE PADS REPLACEMENT-----------------------------------------
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A117-1, A117-2 1991-97 S10 PICKUP & BLAZER 1985-02 ASTRO AND SAFARI VAN Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking
More informationDISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE EXPERIENCED AND COMPETENT IN THE INSTALLATION AND MAINTENANCE OF DISC BRAKES READ ALL WARNINGS
ASSEMBLY INSTRUCTIONS FOR SUPERLITE BIG BRAKE FRONT HUB KIT WITH 1.90 DIAMETER VENTED ROTOR 197-199 CAMARO, DISC/DRUM SPINDLE 197-197 NOVA, DISC/DRUM SPINDLE 19-19 CHEVY II, DRUM SPINDLE WITH MODIFICATIONS
More informationATS metal clutch (twin / triple) instruction manual for Nissan 350Z w/ HR motor 12 pages
ATS metal clutch (twin / triple) instruction manual for Nissan 350Z w/ HR motor 12 pages This instruction is provided by Performance Partners Intl 1 ATS Clutch operating instructions Thank you very much
More informationCHASSIS CONTENTS EXTERIOR PARTS 6-1 FRAME COVER 6-2 REAR FRAME COVER 6-4 FRONT WHEEL 6-6 FRONT BRAKE 6-10 HANDLEBARS 6-17 FRONT FORK 6-19
CHASSIS CONTENTS EXTERIOR PARTS 6- FRAME COVER 6- REAR FRAME COVER 6-4 FRONT WHEEL 6-6 FRONT BRAKE 6-0 HANDLEBARS 6-7 FRONT FORK 6-9 STEERING 6-6 REAR WHEEL 6-3 REAR BRAKE 6-39 6 REAR SHOCK ABSORBER 6-43
More informationINSTALLATION INSTRUCTIONS. KAWASAKI Concours Handlebar Risers for ABS & Non-ABS Part # HR04042 & HR04042-NABS
INSTALLATION INSTRUCTIONS KAWASAKI Concours14 2008-2015 Handlebar Risers for ABS & Non-ABS Part # HR04042 & HR04042-NABS IMPORTANT: PLEASE GIVE CUSTOMER ENCLOSED INFORMATION! Thank you for your purchase
More informationINSTALLATION GUIDE. Doc ID Revision
REKLUSE MOTOR SPORTS OVERVIEW INSTALLATION GUIDE Doc ID 191-6301 Revision 123016 Read the separate included Safety Information document before operating the vehicle with the product installed. If you are
More informationInstallation Manual. Model T680A/B Engine Brakes. For Mack 6 Cylinder, 4 Valve Head E6 and E7 Series Engines. Engine Brakes
Engine Brakes Installation Manual Model T680A/B Engine Brakes For Mack 6 Cylinder, 4 Valve Head E6 and E7 Series Engines TecBrake P.O. Box 27822 Houston, Texas 77227 INSTALLATION MANUAL TECBRAKE T680A
More informationJBrake.com Made in the U.S.A. Forums.SuperTrapp.com P:
Master Index 3 FORWARD CONTROLS & PEGS: J-FL Forward Controls 131 Classic Solid Forward Controls 132-133 Radial Slotted Forward Controls 134-135 J-FX Forward Controls 136-137 Pegs 138-139 HAND CONTROLS
More informationTOYOTA TUNDRA BIG BRAKE KIT Section I - Installation Preparation
TOYOTA TUNDRA 2007- BIG BRAKE KIT Section I - Installation Preparation Part Number: PTR09-34070 Kit Contents Item # Quantity Reqd. Description 1 1 Brake Rotor, LH Front 2 1 Brake Rotor, RH Front 3 1 Brake
More informationService Manual. #19 Gearmatic Winch
Allis Chalmers Service Manual #19 Gearmatic Winch Service Manual THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF ALLIS CHALMERS OR IT S SUCCESSORS. ALLIS CHALMERS AND IT S SUCCESSORS
More informationMaster Cylinders, Boosters, Brackets, Valves and Vacuum Pumps
Master Cylinders, Boosters, Brackets, Valves and Vacuum Pumps When adapting larger brakes to your car we need to ensure that the volume displacement of the master cylinder matches the requirements of the
More informationINSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE GL1500 RAKE KIT
INSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE GL1500 RAKE KIT Thank you for choosing the Motor Trike GL1500 Rake Kit. We ask that you read the directions before you start and follow them very closely.
More informationASSEMBLY INSTRUCTIONS FOR PART NUMBER GROUP
ASSEMBLY INSTRUCTIONS FOR DYNAPRO 6 BIG BRAKE FRONT HAT KIT, 1.19 DIAMETER VENTED ROTOR 1990-005 ACURA/CIVIC ( LUG) 000-003 CIVIC SI ( LUG) 007 - PRESENT HONDA FIT FOR FACTORY 6 mm DISC SPINDLE PART NUMBER
More informationJRC ENGINEERING INC 3110 Indian Ave Suite E Perris, California
JRC ENGINEERING INC 3110 Indian Ave Suite E Perris, California 92571 800-634-3250 Thank you for choosing our 750 conversion for your Triumph 650. Careful assembly and running in will greatly extend the
More informationSD Bendix E-10PR Retarder Control Brake Valve DESCRIPTION. OPERATION - Refer to Figure 2
SD-03-832 Bendix E-10PR Retarder Control Brake Valve MOUNTING PLATE SUPPLY 4 PORTS ELECTRICAL AUXILIARY DESCRIPTION TREADLE RETARDER CONTROL SECTION EXHAUST DELIVERY 4 PORTS FIGURE 1 - E-10PR RETARDER
More information