Preventive Maintenance Inspection Form: Trailers

Size: px
Start display at page:

Download "Preventive Maintenance Inspection Form: Trailers"

Transcription

1 Preventive Maintenance Inspection Form: Trailers A. Under Structure Test glad hands (glad hand with gauge and valve) Air hose Review history record and insure that parts necessary to complete inspection are available. ITEM / NOTES 1) Check for current registration and permits. Check condition of glad hand rubbers. Connect test glad hand and air hose to service emergency lines. Shut off valve on test glad hand. Disconnect air supply and note pressure. Cart Kingpin gauge Grease gun Drop light Oil can Creeper Landing gear crank Inspection form and repair order Move cart with tools and equipment to landing gear leg. Walk to front of trailer and note any air pressure loss on test glad hand (air pressure should not drop more than 2 psi per minute with brakes engaged.) Install landing gear crank. ITEM / NOTES 2) Inspect lower landing: gears (high and low range), rods and connections. Inspect landing gear mounting and brackets: alignment and condition of pad mounting to legs. Clean and inspect landing gear legs and pads. Apply light coating of lubricant over leg segment and lube fittings. 3) Inspect kingpin plate (use kingpin gauge if necessary).

2 Four jack stands Mechanic: Obtain floor jack when necessary and lift rear of trailer. Place stands under bumper or axle with all tires clear of floor. ITEM / NOTES 4) Inspect frame rails for cracks, mounting, corrosion and damage. Touch up undercoatings. Inspect cross members for cracks, mounting, corrosion and damage. Touch up undercoats. Inspect air lines and fittings for routing, chafing and damage. Air is applied during this inspection so any leaks will be evident. 5) Inspect relay valves for mounting and leaks. Inspect wiring conduit for routing, chafing and damage. Inspect mud flaps for mounting and condition. B. Axles, Brakes and Springs Tools to adjust brakes Grease gun Oil can Get on creeper at rear of trailer with tools and drop light. ITEM / NOTES 6) Inspect air hoses and fittings at rear axle. If double trailer, check for routing, chafing and condition. Inspect air tank and bleeder valve for mounting and damage. Bleed air tank and inspect brake chambers for operation and mounting. Note operation of slack adjusters by pulling on them or by applying air. Inspect spring for broken leaves and alignment. Rebound clips and center bolts for proper mounting. Inspect U-bolts and saddles. Tighten if signs of looseness. Use 3 breaker bar. Should measure approximately 395 feet per pound. Inspect hangers and brackets for wear and secure mounting. Inspect radius rods for mounting, damage and bushing wear. Check axles for damage and shifted condition. Inspect slack adjuster and clevis pin lube. Inspect brake cam and bushings for wear. Lube: do not over-grease.

3 ITEM / NOTES 7) If brakes are not being replaced, adjust brakes on both axles. Back off brakes and axles if necessary (for brake removal only if a brake job is scheduled after the PM). Inspect right side same as left. 8) Roll to front axle air tank - inspect air hoses and fittings at front axle check for routing, chafing and condition. Inspect air tank and bleeder valve for mounting and damage. Bleed air tank and inspect brake chambers for operation and mounting - note operation of slack adjusters. Starting at right side, repeat inspection and lube. Return tools and equipment except creeper and drop light. Fill out PMI form and repair order as needed. C. Wheel Assemblies Mechanic s seat Tools to adjust brakes Bar to check bearing play Tool to probe tires Tread depth gauges Tire pressure gauge and inflator Rags Inspection form and repair order Place tools and equipment on cart and move to left front wheel couple air hose to inflator. ITEM / NOTES 9) Inspect rims and lock rings for cracks, rust and proper seating of lock rings. Probe and inspect left front tires. Check tread depths check tire pressures If tires are 15 psi low, remove and check for leaks. Air to correct specifications. Check tire matching with a straight edge. Tires are not to exceed 1/16 out of match. Inspect metal valve caps, seals and stems. Inspect lug nuts for looseness and rust. Place drain pan under hub and remove hubcap. Clean and inspect hub for damage. Inspect wheel-bearing play.

4 ITEM / NOTES 10) Inspect condition of undercoating in wheel well area. Service and inspect all wheel assemblies using this sequence: (a) Complete left rear, (b) right front and (c) end at right rear. Obtain floor jack, remove jack stands from under trailer and lower trailer to floor. Put jacks and stands away. Kingpin adapter Two axle extensions Metal tape with ring Install axle extension on left front axles. Install kingpin adapter, attach metal tape and measure distance to left axle extension. Use creeper to roll under trailer to right side and install second extension on right axle. Measure distance to right axle extension and compare to distance measured to left (1/4 maximum variance from kingpin to axle). Replace all hubcaps using new gaskets. Fill hubs to proper level. D. Door and Interior Drop light Lubricant for overhead door tracks and hinges (dry tape) ITEM / NOTES 11) Walk to closed rear door of trailer. Inspect door cables for tension, alignment, and fraying. Inspect safety chain and latch for secure mounting and proper operation and adjustment. Lube. Inspect weather seals for condition. Inspect door panels for damage and deterioration. Open door. Check balance. Observe condition of tracks and stops. 12) Inspect ceiling, equipment, walls, mountings and stops at rear of trailer. 13) Inspect floor for damage and corrosion.

5 E. Body and Lights Can of undercoating Screwdriver Tools to open and inspect nose box Needle-nose pliers to remove bulbs Supply of bulbs and lenses Light circuit checker Position light circuit checker at front corner on same side convex mirror. ITEM / NOTES 14 ) If hinged, open and inspect nose box. Inspect wiring and connections for corrosion and condition. Inspect circuit breakers for secure mounting, corrosion and connections. Inspect condition of trailer light plug, terminals and lid. Connect light circuit checker. Clean contacts with wire brush cleaner. Use light circuit checker to verify lighting of all circuits individually. Use convex mirror to observe lights on rear of unit. Leave clearance and market light circuits on. 15) Inspect roof for damage. 16) Continue inspection of all clearance lights, reflectors, roof (if applicable), side panels and rub rails moving along the side of the trailer. Look for signs of corrosion on bottom rail. Inspect signs and permit numbers for condition and proper placement. Inspect condition of paint or coatings on steel body parts. Continue inspection across front of trailer and along other side finishing with inspection of upper marker lights. 17) Inspect rear bumper, springs and pads. Check for damage and mounting. Inspect and service taillights in same manner as clearance lights. Inspect reflectors. Inspect license plate light and license plates for condition and secure mounting. Return hand tools and equipment. Walk to front of trailer. Turn off light circuit checker and disconnect. (Note that pintle trailers must be checked from the rear electrical plug for proper operation of individual circuits.) Return tools and equipment.

6 Notes About Fleet University Fleet University is the home of free, valuable resources that make fleet management more productive. These materials are based on the best practices that Ron Turley developed while saving UPS nearly $100 million during five years as their national director of maintenance in the 1970s. Adjusted for inflation, that figure would be over $300 million today. Ron had one of the first authoritative voices in the fleet management industry, and his influence continues today. Following UPS, he consulted with over 170 organizations in the U.S., Canada, the Caribbean, Far East, Europe and South America. His best practices became the foundation of RTA fleet management software over 35 years ago. Fleet University continues in the same spirit of improving productivity through attention to details and data, regardless of what software a fleet manager uses. Discover more free resources from Fleet University at RTAfleet.com/fleetuniversity. Fleet University is presented by Ron Turley Associates, Inc. All rights reserved N. 71st Drive, Suite 110 Glendale, AZ Phone: rtafleet.com rtafleet@rtafleet.com

Inspection Form: Vehicles

Inspection Form: Vehicles Inspection Form: Vehicles A. Engine Operation Materials: Tool to remove battery covers Tool to remove engine splash guards Can of dry solvent-type lubricant Rag Flashlight Has the vehicle s exterior been

More information

TRUCKINGTRUTH.COM T T. Daniel B s Pre-Trip Inspection Checklist

TRUCKINGTRUTH.COM T T. Daniel B s Pre-Trip Inspection Checklist TRUCKINGTRUTH.COM T T Daniel B s Pre-Trip Inspection Checklist 1 My pre-trip begins as I approach the vehicle. I am looking for leaks, leaning one way or the other (which may indicate a low tire or bad

More information

PRE-TRIP INSPECTION CDL SKILLS TEST

PRE-TRIP INSPECTION CDL SKILLS TEST CDL SKILLS TEST PRE-TRIP INSPECTION Engine Compartment +1 Axle Side and Back of Truck +1 Axle Connections and Trailer +1 Axle External Light Check In-Cab with Brake Check 1810 N WATKINS RD, WATKINS, CO

More information

PRE-TRIP Inspection. CDL Skills Test

PRE-TRIP Inspection. CDL Skills Test CDL Skills Test PRE-TRIP Inspection Engine Compartment +1 Axle Side and Back of Truck +1 Axle Connections and Trailer +1 Axle External Light Check In-Cab with Brake Check 7505 Dahlia St. Commerce City,

More information

Code Description of Repair Mfgr Increments Hours

Code Description of Repair Mfgr Increments Hours Repair Labor Code Description of Repair Mfgr Increments Hours Main Frame - Structure 1.0 All Main Frame Structural Steel Components CROWLEY MARITIME CORPORATION CROWLEY FLAT RATE SCHEDULE CHASSIS EXHIBIT

More information

Taking the CDL Pre-trip Inspection Test

Taking the CDL Pre-trip Inspection Test Taking the CDL Pre-trip Inspection Test Class A Pre-trip Inspection Test: If you are applying for a Class A CDL, you will be required to perform a pre-trip inspection in the vehicle you have brought with

More information

SRT OPERATIONS MANUAL

SRT OPERATIONS MANUAL MAINTENANCE SECTION PAGE # VEHICLE DAILY INSPECTION.......................................1 P.M. INSPECTION #1.................................................3 P.M. INSPECTION #2.................................................6

More information

ESCONDIDO FIRE DEPT TRAINING MANUAL Section DRIVER OPERATOR Page 1 of 13 Pre-Trip Inspection Revised

ESCONDIDO FIRE DEPT TRAINING MANUAL Section DRIVER OPERATOR Page 1 of 13 Pre-Trip Inspection Revised DRIVER OPERATOR Page 1 of 13 PRE-TRIP INSPECTION The purpose of a vehicle inspection is to identify systems or parts of a vehicle that are not working properly, have failed or are missing parts so that

More information

Hands On Test Scoring Instructions

Hands On Test Scoring Instructions Hands On Test Scoring Instructions Each scoring box contains 3 to 6 line items and up to 7 numbers plus a 0. Each section has a separate criteria for scoring. Based on the criteria, you will score the

More information

Other employees or individuals are not allowed to start, pre-trip, or drive the bus without permission from the Transportation Office.

Other employees or individuals are not allowed to start, pre-trip, or drive the bus without permission from the Transportation Office. Pre-Trip Inspection January 27, 2014 Drivers Pre-Trip Inspection The Virginia State Department of Education and Virginia Department of Motor Vehicles REQUIRE a pre-trip inspection. A check must be put

More information

As a safety precaution, remove keys from the ignition while working under or around the vehicle.

As a safety precaution, remove keys from the ignition while working under or around the vehicle. CAB AND CHASSIS As a safety precaution, remove keys from the ignition while working under or around the vehicle. 1. Approach Check the overall appearance of vehicle stance (not leaning). Check for signs

More information

CDL Series Pre-Trip Inspection AT-TC3TS T1-JA01. Pre-Trip Inspection Checklist

CDL Series Pre-Trip Inspection AT-TC3TS T1-JA01. Pre-Trip Inspection Checklist Pre-Trip Inspection Checklist This checklist covers different parts of the vehicle you would check before a trip. Note that some specifications described in the following content may not be the same as

More information

DRIVER S GUIDE. For VEHICLE INSPECTIONS

DRIVER S GUIDE. For VEHICLE INSPECTIONS DRIVER S GUIDE For VEHICLE INSPECTIONS The United States Laws and Federal regulations published herein are in public domain. Due to the constantly changing nature of government regulations, it is impossible

More information

Department of Motor Vehicles Loudoun County Public Schools School Bus Inspection Study Guide Hand Out

Department of Motor Vehicles Loudoun County Public Schools School Bus Inspection Study Guide Hand Out Department of Motor Vehicles Loudoun County Public Schools School Bus Inspection Study Guide Hand Out During the actual tests, you will be expected to point or touch each of the parts of your vehicle.

More information

Pre-Trip Inspection Tractor Trailer

Pre-Trip Inspection Tractor Trailer Pre-Trip Inspection Tractor Trailer CHECK OUTSIDE IN FRONT OF YOUR VEHICLE (Front of Vehicle, Lights/Reflectors, Engine Compartment & Steering Components) 1. Clearance lights, head lights, four-way flasher

More information

Vehicle Inspection Study Guide TRUCK/TRAILER (PINTLE HOOK)

Vehicle Inspection Study Guide TRUCK/TRAILER (PINTLE HOOK) Department of Motor Vehicles Vehicle Inspection Study Guide TRUCK/TRAILER (PINTLE HOOK) During the actual tests, you will be expected to point to or touch each of the parts of your vehicle listed below.

More information

Section 11 Vehicle Inspection Test

Section 11 Vehicle Inspection Test Section 11 Vehicle Inspection Test This Section Covers Internal Inspection External Inspection During the Vehicle inspection, you must show that the vehicle is safe to drive. You will have to walk around

More information

A SYSTEMATIC SEQUENCE FOR PM INSPECTIONS

A SYSTEMATIC SEQUENCE FOR PM INSPECTIONS A SYSTEMATIC SEQUENCE FOR PM INSPECTIONS TYPE OF INSPECTION UNDER THE HOOD GASOLINE AND DIESEL 1 Fuel, oil, exhaust leaks - inspect 2 Oil and fuel lines inspect for kinks and wear 3 Automatic transmission

More information

ABS Components Air Compressors Air Dryers & Cartridges Air Tanks. Air Disc Brakes Bearings Brake Pads Brake Rotors Brake Shoes & Kits Camshafts & Kits

ABS Components Air Compressors Air Dryers & Cartridges Air Tanks. Air Disc Brakes Bearings Brake Pads Brake Rotors Brake Shoes & Kits Camshafts & Kits Air Brake Systems ABS Components Air Compressors Air Dryers & Cartridges Air Tanks Air Valves Brass Fittings Composite Fittings Coiled Air Hoses Glad Hands Nylon Tubing Rubber Hoses Tire Valves Brake &

More information

Seabee Annual/100-Hour Inspection

Seabee Annual/100-Hour Inspection Date Completed Seabee Annual/100-Hour Inspection ENGINE Mechanic s Initials 1 Drain engine oil and check for foreign material 2 Check oil screen for proper rotation or looseness 3 Safety Oil Plug 4 Refill

More information

LA County Fire Department Pre -Trip Inspection Class B Vehicles

LA County Fire Department Pre -Trip Inspection Class B Vehicles LA County Fire Department Pre -Trip Inspection Class B Vehicles Pre Trip Inspection This slide program was designed to assist firefighter s s with their pre trip inspection This slide program comes with

More information

Pre-Trip Inspection Bus, School Bus.

Pre-Trip Inspection Bus, School Bus. Pre-Trip Inspection Bus, School Bus. CHECK OUTSIDE IN FRONT OF YOUR VEHICLE (Front of Vehicle, Lights/Reflectors, Engine Compartment & Steering Components) 1. Clearance lights, alternately flashing amber

More information

Trailer Parts. Brake Components. Axle Components. Suspensions. Lights & Electrical. Wheels & Tires. Loading Ramps. Couplers & Safety Chains

Trailer Parts. Brake Components. Axle Components. Suspensions. Lights & Electrical. Wheels & Tires. Loading Ramps. Couplers & Safety Chains Trailer Parts Brake Components Axle Components Suspensions Lights & Electrical Wheels & Tires Loading Ramps Couplers & Safety Chains Trailer Jacks Fenders Dump Trailer Parts Tilt SST Parts Decal Kits Brake

More information

Section 11 Vehicle Pre-Trip Inspection

Section 11 Vehicle Pre-Trip Inspection Section 11 Vehicle Pre-Trip Inspection Air Gauge Make sure the air gauge is working properly. Build air pressure to governor cut-out, roughly 120 to 140 psi. Removed Parking Brake Check With the parking

More information

Pre and Post Trip Inspection for School Bus Drivers Video Reference Guide and Test

Pre and Post Trip Inspection for School Bus Drivers Video Reference Guide and Test 1 Pre and Post Trip Inspection for School Bus Drivers Video Reference Guide and Test Produced by Video Communications www.safetyvideos.org 2 INTRODUCTION School buses are complicated pieces of equipment.

More information

i. ii. iii. iv. 1. HYDRAULIC CYLINDER PIVOT PIN GREASE TWO PLACES 2. 5 TH PLATE- DRAFT ARM CONNECTION GREASE TWO PLACES 3. DRAFT ARM- BOLSTER CONNECTION GREASE TWO PLACES 4. HIGH LIFT GATE HINGE GREASE

More information

ATV 90 UTILITY GREEN (A2006KUB2BUSG) Page 1 of 60 AIR INTAKE ASSEMBLY

ATV 90 UTILITY GREEN (A2006KUB2BUSG) Page 1 of 60 AIR INTAKE ASSEMBLY 2006 ATV 90 UTILITY GREEN (A2006KUB2BUSG) Page 1 of 60 AIR INTAKE ASSEMBLY 2006 ATV 90 UTILITY GREEN (A2006KUB2BUSG) Page 2 of 60 AIR INTAKE ASSEMBLY Ref # Part Number Qty S/P/F Description 1 3303-005

More information

Trailer Parts. Brake Components. Axle Components. Suspensions. Lights & Electrical. Wheels & Tires. Loading Ramps. Couplers & Safety Chains

Trailer Parts. Brake Components. Axle Components. Suspensions. Lights & Electrical. Wheels & Tires. Loading Ramps. Couplers & Safety Chains Trailer Parts Brake Components Axle Components Suspensions Lights & Electrical Wheels & Tires Loading Ramps Couplers & Safety Chains Trailer Jacks Fenders Dump Trailer Parts Tilt SST Parts Decal Kits Brake

More information

CLASS B PRE-TRIP VEHICLE INSPECTION

CLASS B PRE-TRIP VEHICLE INSPECTION Warren County ESC 320 E. Silver Street Lebanon, OH 45036 April 1, 2006 CLASS B PRE-TRIP VEHICLE INSPECTION A vehicle inspection test evaluates your ability to inspect important parts of a commercial vehicle.

More information

ATV 90 UTILITY CALIFORNIA GREEN (A2008KUB2BCAG) Page 1 of 58 AIR INTAKE ASSEMBLY

ATV 90 UTILITY CALIFORNIA GREEN (A2008KUB2BCAG) Page 1 of 58 AIR INTAKE ASSEMBLY 2008 ATV 90 UTILITY CALIFORNIA GREEN (A2008KUB2BCAG) Page 1 of 58 AIR INTAKE ASSEMBLY 2008 ATV 90 UTILITY CALIFORNIA GREEN (A2008KUB2BCAG) Page 2 of 58 AIR INTAKE ASSEMBLY Ref # Part Number Qty S/P/F Description

More information

As stated, these are solely based off of how I like to do the Pre-Trip. I give my personal opinions as well as some helpful tips.

As stated, these are solely based off of how I like to do the Pre-Trip. I give my personal opinions as well as some helpful tips. Here are our sections: Engine Compartment Drivers Door Fuel Area Coupling System Trailer (Please note in the type of suspension your trailer has) Light Check In-Cab Inspection and Brake Tests You will

More information

ATV 50 DVX BLACK-RED (A2008KSA2BUSD) Page 1 of 60 AIR INTAKE ASSEMBLY

ATV 50 DVX BLACK-RED (A2008KSA2BUSD) Page 1 of 60 AIR INTAKE ASSEMBLY 2008 ATV 50 DVX BLACK-RED (A2008KSA2BUSD) Page 1 of 60 AIR INTAKE ASSEMBLY 2008 ATV 50 DVX BLACK-RED (A2008KSA2BUSD) Page 2 of 60 AIR INTAKE ASSEMBLY Ref # Part Number Qty S/P/F Description 1 3303-005

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTRUCTION FOR ASSEMBLY OF JEEP CJ SERIES W/AMC 20 REAR AXLES, 5 x 5-1/2" BOLT CIRCLE WITH A130-1 FULL FLOATING AXLE OR A130-2 (1 PIECE AXLE) Thank you for choosing STAINLESS

More information

CHASSIS CONTENTS FRONT WHEEL 6-1 FRONT BRAKE 6-6 FRONT FORK 6-14 STEERING STEM 6-20 REAR WHEEL AND REAR BRAKE 6-25 SUSPENSION 6-31 REAR SWING ARM 6-36

CHASSIS CONTENTS FRONT WHEEL 6-1 FRONT BRAKE 6-6 FRONT FORK 6-14 STEERING STEM 6-20 REAR WHEEL AND REAR BRAKE 6-25 SUSPENSION 6-31 REAR SWING ARM 6-36 CHASSIS CONTENTS FRONT WHEEL 6-1 FRONT BRAKE 6-6 FRONT FORK 6-14 STEERING STEM 6-20 REAR WHEEL AND REAR BRAKE 6-25 SUSPENSION 6-31 REAR SWING ARM 6-36 6 6-1 CHASSIS FRONT WHEEL REMOVAL Support the machine

More information

DVX 90 MODEL NUMBER A2008KSB2BUSD (BLACK-RED) MODEL NUMBER A2008KSB2BUSE (BLACK-CAT GREEN) MORE TO GO ON. TM

DVX 90 MODEL NUMBER A2008KSB2BUSD (BLACK-RED) MODEL NUMBER A2008KSB2BUSE (BLACK-CAT GREEN) MORE TO GO ON. TM 2008 DVX 90 Illustrated Parts Manual MODEL NUMBER A2008KSB2BUSD (BLACK-RED) MODEL NUMBER A2008KSB2BUSE (BLACK-CAT GREEN) MORE TO GO ON. TM TABLE OF CONTENTS Black-Red (Model No. A2008KSB2BUSD) Black-Cat

More information

FASTENERS, SPRINGS, DETENT BALLS & MISC. HARDWARE PAINT, SEALANT, ADHESIVES, DECALS & LEAK DETECTORS

FASTENERS, SPRINGS, DETENT BALLS & MISC. HARDWARE PAINT, SEALANT, ADHESIVES, DECALS & LEAK DETECTORS CROSS REFERENCE LANDING LEG PARTS TWISTLOCK & PINLOCK ASSEMBLIES & PARTS STEEL PANELS & STRUCTURAL STEEL ALUMINUM EXTRUSIONS & STRUCTUAL COMPONENTS DOOR HARDWARE AXLES, SUSPENSION PARTS, 5TH WHEEL & COMPONENTS

More information

Commercial Vehicle Pre-Trip Inspection Checklist

Commercial Vehicle Pre-Trip Inspection Checklist Commercial Vehicle Pre-Trip Inspection Checklist The Commercial Vehicle Pre-Trip Inspection Test is designed to test your ability to check a variety of commercial vehicle safety equipment and vehicle components.

More information

T6 Owners Manual. Basic Function

T6 Owners Manual. Basic Function T6 Owners Manual Basic Function The T6 is a frameless aluminum end dump trailer. It is used mainly for hauling sand, gravel and dirt. The material is discharged by extending the hoist which raises the

More information

SHERMAN VOLUNTEER FIRE DEPARTMENT SVFD DRIVER TRAINING INFORMATION

SHERMAN VOLUNTEER FIRE DEPARTMENT SVFD DRIVER TRAINING INFORMATION SHERMAN VOLUNTEER FIRE DEPARTMENT SVFD DRIVER TRAINING INFORMATION The State of Connecticut requires any member operating a vehicle over 26,000 lbs. gross vehicle weight (GVW) to have at the minimum a

More information

MARYLAND COMMERCIAL DRIVER'S LICENSE PRE-TRIP INSPECTION GUIDE

MARYLAND COMMERCIAL DRIVER'S LICENSE PRE-TRIP INSPECTION GUIDE MARYLAND COMMERCIAL DRIVER'S LICENSE PRE-TRIP INSPECTION GUIDE This guide has five sections: Engine Compartment In-Cab Checks Outside of Vehicle Air Brake Test School Bus Applicants may conduct the Pre-Trip

More information

Driver s Vehicle Inspection Report

Driver s Vehicle Inspection Report Driver s Vehicle Inspection Report Check ANY Defective Item and Give Details under Remarks. DATE: TRuCk/TRACTOR NO. Air Compressor Air Lines Battery Brake Accessories Brakes Carburetor Clutch Defroster

More information

For Use With Power Units Mounted on M200A1 Trailers Only

For Use With Power Units Mounted on M200A1 Trailers Only TASK COMPLETION WORKSHEET WORK ORDER# SERIAL # Form : Each task shall be completed by an individual working in the section listed for the task. This individual shall write their employee number in the

More information

LIFT Standard A-Arm Lift Kit Club Car Precedent Installation Instructions

LIFT Standard A-Arm Lift Kit Club Car Precedent Installation Instructions LIFT-563 6 Standard A-Arm Lift Kit Club Car Precedent Installation Instructions Contents of LIFT-563 Club Car Precedent Lift Kit: a (1 ea.) Front Suspension b (1 ea.) Driver Side Upper A-Arm c (1 ea.)

More information

ABS Components Air Compressors Air Dryers & Cartridges Air Tanks. Air Disc Brakes Bearings Brake Pads Brake Rotors Brake Shoes & Kits Camshafts & Kits

ABS Components Air Compressors Air Dryers & Cartridges Air Tanks. Air Disc Brakes Bearings Brake Pads Brake Rotors Brake Shoes & Kits Camshafts & Kits Air Brake Systems ABS Components Air Compressors Air Dryers & Cartridges Air Tanks Air Valves Brass Fittings Composite Fittings Coiled Air Hoses Glad Hands Nylon Tubing Rubber Hose Tire Valves Brake &

More information

TABLE OF CONTENTS Pre Trip and Post Trip Inspections

TABLE OF CONTENTS Pre Trip and Post Trip Inspections TABLE OF CONTENTS Pre Trip and Post Trip Inspections Introduction. 11 Pre Trip Inspection.. 12 Circle Check.. 12 Rear of Bus...12 Right Side of Bus...13 Air Brake Procedure...13 Post Trip Inspection. 13

More information

Owner s Manual Enclosed Cargo

Owner s Manual Enclosed Cargo Owner s Manual Enclosed Cargo 1 This manual contains safety information and instructions for your trailer. You must read this manual before loading or towing your trailer. You must follow all safety precautions

More information

90 Utility Model Number A2013KUB2BUSZ SHARE OUR PASSION.

90 Utility Model Number A2013KUB2BUSZ SHARE OUR PASSION. 2013 90 Utility Model Number A2013KUB2BUSZ TM SHARE OUR PASSION. TABLE OF CONTENTS 2013 ATV 90 (Model No. A2013KUB2BUSZ) BODY PANEL AND HEADLIGHT ASSEMBLY... 1 FRONT AND REAR RACK ASSEMBLY... 2 FRAME AND

More information

ATV I l. l u. r a. Parts Manual ARCTIC CAT. 250 cc/300 cc

ATV I l. l u. r a. Parts Manual ARCTIC CAT. 250 cc/300 cc 2000 I l l u st ATV 250 cc/300 cc Model No. A2000ATE2AUSG (250 - Green) Model No. A2000ATE2AUSR (250 - Red) Model No. A2000ATF2AUSG (300 2x4 - Green) Model No. A2000ATF2AUSR (300 2x4 - Red) Model No. A2000ATF4AUSG

More information

Diesel Technology: Steering and Suspension

Diesel Technology: Steering and Suspension Diesel Technology: Steering and Suspension National Skills Crosswalk The following NATEF Suspension and Steering tasks (rev. 2004) are covered in this publication. The chart shows where each task is located

More information

Commercial Driver s License Manual SECTION 7. Section-7 Doubles and Triples

Commercial Driver s License Manual SECTION 7. Section-7 Doubles and Triples SECTION 7 doubles and triples this section Is for drivers WHo WIll tow double or triple trailers Section-7 Doubles and Triples section 7 - doubles and triples this section covers Pulling double/triple

More information

Rear Toyota Landcruiser 4x4 S-W GX 91 Onwards

Rear Toyota Landcruiser 4x4 S-W GX 91 Onwards 60728A0 Rear Toyota Landcruiser 4x4 S-W 80-100 GX 91 Onwards LOWER SPRING SEAT.DRILLING INSTRUCTIONS 6. The picture above shows the expected result after drilling the hole in step 4. 1. The spring seat

More information

WEDICO. `çãéäéíé=háí= q~êéjqçé=péãájqê~áäéê= Art.-No. 63

WEDICO. `çãéäéíé=háí= q~êéjqçé=péãájqê~áäéê= Art.-No. 63 WEDICO `çãéäéíé=háí= q~êéjqçé=péãájqê~áäéê= Art.-No. 6 Measurements Chassis and superstructure Finish Assembly Length...768 mm Width...7 mm Height...65 mm Weight...8 kg Frame made of aluminium section,

More information

OPERATOR S MANUAL MAINTENANCE MANUAL PARTS LIST TURFCO METE-R-MATIC III. Top Dresser. Model F12D. Product Number 85423

OPERATOR S MANUAL MAINTENANCE MANUAL PARTS LIST TURFCO METE-R-MATIC III. Top Dresser. Model F12D. Product Number 85423 Model FD OPERATOR S MANUAL MAINTENANCE MANUAL PARTS LIST TURFCO Top Dresser Model FD Product Number U.S. Patents,,;,0,;,0, Other Patents Pending Manual Number Rev B DANGER - IF INCORRECTLY USED THIS MACHINE

More information

INSTRUCTIONS, (FORD) SUPER DUTY INSTALLATION KIT (C2 PICKUP LIFTGATES)

INSTRUCTIONS, (FORD) SUPER DUTY INSTALLATION KIT (C2 PICKUP LIFTGATES) LIFT CORPORATION Sht. 1 of 20 DSG# M-14-32 Rev. B Date: 05/31/2017 INSTRUCTIONS, (FORD) SUPER DUTY INSTALLATION KIT (C2 PICKUP LIFTGATES) FORD SUPER DUTY F-250 PICKUP TRUCKS, 1999-2016 FORD SUPER DUTY

More information

UNPACK AND IDENTIFY THE FOLLOWING PARTS.

UNPACK AND IDENTIFY THE FOLLOWING PARTS. SUT-500-S ASSEMBLY REQUIREMENTS *Torque all T-bolt nuts to 35-40 foot pounds. *Check all lights before towing. *Tire pressure not to exceed recommendation on serial tag. *Re-torque wheel nuts after first

More information

USER MANUAL. Keep this User Manual in the vehicle on which Halos are installed.

USER MANUAL. Keep this User Manual in the vehicle on which Halos are installed. Keep this User Manual in the vehicle on which Halos are installed. USER MANUAL 3 IMPORTANT SAFETY INFORMATION The Halo is not intended to replace regular pressure-checks and tire maintenance practices

More information

Installation Instructions

Installation Instructions Installation Instructions Rear Disc Brake Conversion Kit Item # RC4001, RC4001X Applications: Mopar 7.25, 8.25, 9.25 Axles Thank you for choosing Leed Brakes for your automotive product needs. Before you

More information

<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W Trailer Hitches 1216 Hawaii Road / PO Box 186 Humboldt, KS P: F:

<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W Trailer Hitches 1216 Hawaii Road / PO Box 186 Humboldt, KS P: F: B&W Trailer Hitches 26 Hawaii Road / PO Box 86 Humboldt, KS 66748 P:620.473.3664 F:620.869.903 Ford OEM Mount System Installation Instructions 20,000

More information

AmTryke Adult Recumbent Model JT2000 #50-FC-2000

AmTryke Adult Recumbent Model JT2000 #50-FC-2000 AmTryke Adult Recumbent Model JT2000 #50-FC-2000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable

More information

BRAKE SYSTEM Return To Main Table of Contents

BRAKE SYSTEM Return To Main Table of Contents BRAKE SYSTEM Return To Main Table of Contents GENERAL... 2 BRAKE PEDAL... 10 MASTER CYLINDER... 13 BRAKE BOOSTER... 16 BRAKE LINE... 18 PROPORTIONING VALVE... 19 FRONT DISC BRAKE... 20 REAR DRUM BRAKE...

More information

All outside contractors have to be qualified by Fleet Services.

All outside contractors have to be qualified by Fleet Services. Vehicle Practice Practice: Reference: 1 of 7 1.0 INTRODUCTION The Preventive Maintenance Inspection Program is designed to ensure routine service functions are performed at regular intervals on Company

More information

Salem, OhioSalem, Ohio

Salem, OhioSalem, Ohio OWNER S MANUAL FLATBED TRAILERS Alliance, Ohio Salem, Ohio Salem, Ohio 14599 Commerce St. 1453 Allen 1453 Rd. Allen Rd. Alliance, Ohio 44601 Salem, OhioSalem, Ohio Phone: 330.823.9900 Phone: 330.829.1680

More information

DEMOUNTABLE BODY INSPECTION PROCEDURE Follow Detailed Instructions Inside for Each Step

DEMOUNTABLE BODY INSPECTION PROCEDURE Follow Detailed Instructions Inside for Each Step DEMOUNTABLE BODY INSPECTION PROCEDURE Follow Detailed Instructions Inside for Each Step Inspection Date: Inspected By: Serial #: Unit #: INSPECT: Inspected OK Needs Repair Comments Front Locking Bar Rear

More information

Time Task Tariff JOB NO CHASSIS JOB DESCRIPTION Time/Hours*

Time Task Tariff JOB NO CHASSIS JOB DESCRIPTION Time/Hours* Time Task Tariff JOB NO CHASSIS JOB DESCRIPTION Time/Hours* 10001 Main Frame - Straighten (GS) - First 12 in. 0.50 10002 Main Frame - Straighten (GS) - Ea. add'l 12 in. 0.50 10003 Main Frame - Straighten

More information

WEDICO. `çãéäéíé=háí= `çåí~áåéê=péãájqê~áäéê= Art.-No. 64 white

WEDICO. `çãéäéíé=háí= `çåí~áåéê=péãájqê~áäéê= Art.-No. 64 white WEDICO `çãéäéíé=háí= Art.-No. 6 white Measurements Chassis and superstructure Finish Assembly Length...78 mm Width...65 mm Height...58 mm Weight...7 kg Frame made of aluminium section, mm thick; torsion

More information

11/14/ U. Baja Motorsports Inc. P.O. Box Phoenix, AZ Toll Free: PARTS AND PRICES ARE SUBJECT TO CHANGE 1 of 53

11/14/ U. Baja Motorsports Inc. P.O. Box Phoenix, AZ Toll Free: PARTS AND PRICES ARE SUBJECT TO CHANGE 1 of 53 250U Toll Free: 888-863-2252 PARTS AND PRICES ARE SUBJECT TO CHANGE 1 of 53 FIG. 1 PNEUMATIC MECHANISM 1-1 250U-100 883099019951 CAMSHAFT 1 1 1-2 250U-101 883099019968 KEY, WOODRUFF 1 1 1-3 250U-102 883099019975

More information

SUT-250-S (These instructions are used for SUT-250-SCLC also)

SUT-250-S (These instructions are used for SUT-250-SCLC also) SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16, 3/4, 13/16,

More information

Kysor On/Off Rear Air Fan Drive

Kysor On/Off Rear Air Fan Drive . Proper precautions must be taken to prevent personal injury from contact with moving parts, unintended engine start, or other hazards present when working with powered equipment. Refer to the vehicle

More information

P/N Figure 1. Figure 2. 3 Valve Stem

P/N Figure 1. Figure 2. 3 Valve Stem P/N 80523 BY MN-75 (12612) ECN1965 ECR 8167 3 Valve Stem 2 1 Figure 1 1 1. Jack up front end of vehicle and place safety stands under axle. Remove front wheels and lower shock absorber attaching bolts.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DRUM TO DISC BRAKE CONVERSION KIT A118 pre-1985 Ford F150 (except 1983-1984 w/super H/D axle) Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.

More information

X4 (GREEN) (A2000ATF2AUSG) Page 1 of 80 AIR INTAKE ASSEMBLY

X4 (GREEN) (A2000ATF2AUSG) Page 1 of 80 AIR INTAKE ASSEMBLY 2000 300 2X4 (GREEN) (A2000ATF2AUSG) Page 1 of 80 AIR INTAKE ASSEMBLY 2000 300 2X4 (GREEN) (A2000ATF2AUSG) Page 2 of 80 AIR INTAKE ASSEMBLY Ref # Part Number Qty S/P/F Description 1 3570-001 1 /P Intake,

More information

Seabee Annual Inspection Procedures

Seabee Annual Inspection Procedures Procedures Due to the wide variety of Seabee s flying out there, these procedures should be modified to fit YOUR Seabee. Make sure that all AD s are complied with as well as any required Service Bulletins

More information

CLUTCH-04, Clutch Master Cylinder Replacement

CLUTCH-04, Clutch Master Cylinder Replacement CLUTCH-04, Clutch Master Cylinder Replacement Introduction This procedure details replacement of the clutch master cylinder on 944s and 968s. Terry Jenner did a great job with this procedure. He wrote

More information

DVX 300 Euro. Model Number A2012KSF2BEUK SHARE OUR PASSION.

DVX 300 Euro. Model Number A2012KSF2BEUK SHARE OUR PASSION. ATV 2012ATV Illustrated Parts Manual DVX 300 Euro Model Number A2012KSF2BEUK TM SHARE OUR PASSION. TABLE OF CONTENTS 2012 ATV DVX 300 Euro (Model No. A2012KSF2BEUK) BODY PANEL AND HEADLIGHT ASSEMBLY...

More information

Owner s Manual Hybrid/Crossover

Owner s Manual Hybrid/Crossover Owner s Manual Hybrid/Crossover This manual contains safety information and instructions for your trailer. You must read this manual before loading or towing your trailer. You must follow all safety precautions

More information

FRONT SUSPENSION GROUP 2 FRONT SUSPENSION 2-1 CONTENTS SPECIFICATIONS VC-1, VC-2, VC-3 VY-1 TOOL LIST. Page

FRONT SUSPENSION GROUP 2 FRONT SUSPENSION 2-1 CONTENTS SPECIFICATIONS VC-1, VC-2, VC-3 VY-1 TOOL LIST. Page GROUP 2 FRONT SUSPENSION CONTENTS Page Specifications 1 Tool List.... 1 Torque Reference 2 Preparation for Measuring Front End Alignment... 2 Front Suspension Height Adjustment 3 Front Suspension Alignment

More information

Model 3770 WARNING. Failure to comply with the safety information in these instructions could result in serious injury or death.

Model 3770 WARNING. Failure to comply with the safety information in these instructions could result in serious injury or death. B&W Trailer Hitches 1216 Hawaii Road / PO Box 186 Humboldt, KS 66748 P:620.473.3664 See Limited Lifetime Warranty at F:620.869.9031 bwtrailerhitches.com/warranty NOTE: We recommend reading instructions

More information

Accident Prevention Program

Accident Prevention Program Accident Prevention Program Maintenance Aspects of Owning Your Own Airplane Introduction As an owner-pilot, FAR Part 43 allows you to perform certain types of inspections and maintenance on your airplane.

More information

CYLINDER HEAD. Ref. Part No. Number Description Qty Remarks

CYLINDER HEAD. Ref. Part No. Number Description Qty Remarks A1 CYLINDER HEAD 1 55V-11101-01-00 CYLINDER HEAD ASSEMBLY. 1 2 30X-11133-10-00. GUIDE, INTAKE VALVE..... 4 3 93440-10109-00. CIRCLIP................. 4 4 99510-08016-00. PIN, DOWEL............. 8 5 90105-06153-00.

More information

AmTryke Adult Recumbent Model HP1000 #50-HC-1000

AmTryke Adult Recumbent Model HP1000 #50-HC-1000 AmTryke Adult Recumbent Model HP1000 #50-HC-1000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A128 1990-1995 JEEP WRANGLER (YJ) WITH DANA 35 AXLES (non-abs) Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases

More information

Truck Owner. Heavy Vehicle Inspection Checklist. conducted for. Location Kidman Way, Mount Hope NSW 2877, Australia. Conducted on 27 Mar :07 AM

Truck Owner. Heavy Vehicle Inspection Checklist. conducted for. Location Kidman Way, Mount Hope NSW 2877, Australia. Conducted on 27 Mar :07 AM Heavy Vehicle Inspection Checklist conducted for Truck Owner Location Kidman Way, Mount Hope NSW 2877, Australia Conducted on 27 Mar 2018 09:07 AM Prepared by SafetyCulture Staff Completed on 27 Mar 2018

More information

ATTENTION: THIS IS NOT A RELEASED DOCUMENT. Labor Flat Rates DRAFT. Aeromaster and Truck Body

ATTENTION: THIS IS NOT A RELEASED DOCUMENT. Labor Flat Rates DRAFT. Aeromaster and Truck Body Contents ATTENTION: THIS IS NOT A RELEASED DOCUMENT. Service Guide Labor Flat Rates Aeromaster and Truck Body Flat Rates and Labor Operation Codes...3 Door...3 Side Sliding...3 Swing...4 Bulkhead...4 Rear

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DRUM TO DISC BRAKE CONVERSION KIT A130 JEEP CJ SERIES W/AMC-20 REAR AXLES AND 5 x 5-1/2" BOLT CIRCLE Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking

More information

Part Inspection, Repair, and Maintenance

Part Inspection, Repair, and Maintenance Part 396 - Inspection, Repair, and Maintenance General Requirements (396.3(a)) Every carrier shall systematically inspect, repair, and maintain all commercial motor vehicles under its control. Record Keeping

More information

Installation Instructions

Installation Instructions Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to

More information

TABLE OF CONTENTS 2001 ATV

TABLE OF CONTENTS 2001 ATV TABLE OF CONTENTS 2001 ATV 400/500 cc Manual Transmission 400 2x4 Red (Model No. A2001ATI2AUSR) 400 2x4 Green (Model No. A2001ATI2AUSG) 400 4x4 Red ( Model No. A2001ATI4AUSR) 400 4x4 Green (Model No. A2001ATI4AUSG)

More information

Parts Diagrams RR/RS Models

Parts Diagrams RR/RS Models Parts Diagrams 2008-2009 RR/RS Models Table Of Contents Description Page # front fork 1 handlebar, clutch pump, meter (RR Models) 2 handlebar, clutch pump, meter (RS Models) 3 frame, subframe 4 rear shock,

More information

REQUEST FOR QUOTATIONS

REQUEST FOR QUOTATIONS Public Works Department REQUEST FOR QUOTATIONS 12 14 YARD DUMP TRUCK PURCHASE Due: Thursday, July 27, 2017 No later than 2:00 P.M. Submit to: City of Arroyo Grande Attn: Public Works Department 1375 Ash

More information

STATE OF MINNESOTA PRICING Page % DISCOUNT

STATE OF MINNESOTA PRICING Page % DISCOUNT TRAILERS: DUMP BODY, LOWBOYS, FLATBED, TAG, SLIDE AXLE, UTILITY, GOOSENECK, ENCLOSED, ETC. Vendor Name: Truck Utilities Inc Contact Person: Paul Warner Street Address: 2370 English Street P.O. Box: City,

More information

SMF / DSF / DTF SMF / DSF / DTF 200

SMF / DSF / DTF SMF / DSF / DTF 200 2006 SMF / DSF / DTF 200 1 The drawings in this parts book have been scaled so that parts can be easily recognized. 1 CYLINDER ASSY 2 CYLINDER ASSY Ref # Part # Description 1 410 0001A CYLINDER HEAD COVER

More information

Illustrated Parts Manual. Model Number A2011KSF2BEUZ (Black-Cat Green) A2011KSF2BEOJ (White-Cat Green)

Illustrated Parts Manual. Model Number A2011KSF2BEUZ (Black-Cat Green) A2011KSF2BEOJ (White-Cat Green) Illustrated Parts Manual 2 1 10 DVX 300 Euro Model Number A2011KSF2BEUZ (Black-Cat Green) A2011KSF2BEOJ (White-Cat Green) S H A R E O U R PAS S IO N. TM TABLE OF CONTENTS 2011 ATV DVX 300 Euro Black-Cat

More information

WEDICO. `çãéäéíé=háí= q~åâ=péãájqê~áäéêi=çî~ä= Art.-No. 67 polished. Measurements Length 745 mm Width 160 mm Height 250 mm Weight 3.

WEDICO. `çãéäéíé=háí= q~åâ=péãájqê~áäéêi=çî~ä= Art.-No. 67 polished. Measurements Length 745 mm Width 160 mm Height 250 mm Weight 3. WEDICO `çãéäéíé=háí= Art.-No. 67 polished Measurements Length 745 mm Width 160 mm Height 250 mm Weight 3.8 kg Chassis and superstructure Assembly Frame made of aluminium section, 2 mm thick; torsion resistant.

More information

Remount Proposal. Everest Emergency Vehicles 1133 Rankin Street St Paul, MN Eric Olson

Remount Proposal. Everest Emergency Vehicles 1133 Rankin Street St Paul, MN Eric Olson Remount Proposal Customer Dealer Everest Emergency Vehicles 1133 Rankin Street St Paul, MN 55116 651-236-8943 Eric Olson Module: INFORMATION 0.1.60 ****** Ambulance Re-chassis / Refurbish ****** * * Old

More information

<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W Trailer Hitches 1216 Hawaii Road / PO Box 186 Humboldt, KS P: F:

<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W Trailer Hitches 1216 Hawaii Road / PO Box 186 Humboldt, KS P: F: B&W Trailer Hitches 26 Hawaii Road / PO Box 86 Humboldt, KS 6678 P:620.73.366 F:620.869.903 RAM OEM Mount System Installation Instructions 25,000 LBS.

More information

BRAKE SYSTEM Nissan 240SX DESCRIPTION BRAKE BLEEDING * PLEASE READ FIRST * BLEEDING PROCEDURES ADJUSTMENTS BRAKE PEDAL HEIGHT SPECS TABLE

BRAKE SYSTEM Nissan 240SX DESCRIPTION BRAKE BLEEDING * PLEASE READ FIRST * BLEEDING PROCEDURES ADJUSTMENTS BRAKE PEDAL HEIGHT SPECS TABLE BRAKE SYSTEM 1990 Nissan 240SX 1990 BRAKE SYSTEMS Nissan Disc & Drum Axxess, Maxima, Pathfinder, Pickup, Pulsar NX, Sentra, Stanza, 240SX, 300ZX DESCRIPTION All brake systems are hydraulically operated

More information

Tractor DOT Inspection Customer Name HUDSON VALLEY TRUCK CENTER CRP Inspection 11/15/2018 Date b. Friction Parts (Shoes, Linings,Drums, etc...) c. Hos

Tractor DOT Inspection Customer Name HUDSON VALLEY TRUCK CENTER CRP Inspection 11/15/2018 Date b. Friction Parts (Shoes, Linings,Drums, etc...) c. Hos Tractor DOT Inspection Customer Name HUDSON VALLEY TRUCK CENTER CRP Inspection /5/208 Date b. Friction Parts (Shoes, Linings,Drums, etc...) c. Hoses, Tubing etc... d. Slack Adjuster & Push Rods e. Camshafts,

More information

<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W Trailer Hitches 1216 Hawaii Road / PO Box 186 Humboldt, KS P: F:

<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W Trailer Hitches 1216 Hawaii Road / PO Box 186 Humboldt, KS P: F: B&W Trailer Hitches 26 Hawaii Road / PO Box 86 Humboldt, KS 6678 P:620.73.366 F:620.869.903 Ford OEM Mount System Installation Instructions 20,000 LBS.

More information

Kwik-Loc Corp Tag Axle Installation Manual

Kwik-Loc Corp Tag Axle Installation Manual Kwik-Loc Corp Tag Axle Installation Manual 7340 Dorr St. Toledo, OH 43615 419.867.9393 www.kwikloc.com I. Requirements Most two axle tractors that have a steel frame a minimum of nine inches deep (A).

More information

Land Cruiser FJ80 and FZJ80 Double Swingout Rear Bumper Installation Instructions PRELIMINARY

Land Cruiser FJ80 and FZJ80 Double Swingout Rear Bumper Installation Instructions PRELIMINARY Land Cruiser FJ80 and FZJ80 Double Swingout Rear Bumper Installation Instructions Fits 1991-1997 80 Series Land Cruiser / Lexus LX450 PRELIMINARY Thank you for purchasing a Rear Bumper for your Land Cruiser.

More information