Installation Instructions

Transcription

1 Installation Instructions PlayDesigns Infant FunCenter Installation Preparation Recommended Crew:...Two (2) adults Installation Time:...1 man-hour Use Zone:...Refer to the information below User Group Age:... ASTM: 6-23 months Assembly View ICON KEY Fully Tighten Hardware Add 1 Drop of Thread Locking Adhesive Do Not Fully Tighten Hardware Pour Concrete A Equipment Use Zone A : 36 in. (914 mm) Drill Hammer Dig Footing Holes Critical Fall Height Page 1 of 8

2 KEY Position Top # Bottom # Unit of Measurement Inches [Millimeters] Top View Elevation View Long Panel Frame Panel Tracing Panel 12" (305 mm) Page 2 of 8

3 Follow the details in alphabetical order. For clarifi cation, each detail references the step description. The step descriptions start on page 5. Insert post up through the base and align holes. Center Post BPL0074 FunCenter Base ASY0046 3/8" x 1-1/2" Knob Bolt BAE0077 (2 Total) Detail A Step 3 Attach the center post to the FunCenter base. Page 3 of 8

4 Long Center Panel ASY0055 Tracing Panel ASY0045 Frame Panel ASY0044 Detail B Step 4 Insert the long center panel into the FunCenter base and push down to "snap" in place. Detail C Step 5 Insert the frame and tracing panels into the FunCenter base and push down to "snap" in place. Page 4 of 8

5 Notes Before You Begin: Do not over tighten bolts during assembly, only snug tighten them until assembly is complete. Carefully read and understand these installation instructions before you begin. Step 1: Before attempting to assemble your equipment, please review all installation information carefully. Should you experience any diffi culty during the installation process, please call us at the phone number shown on the last page of these instructions. Step 2: Separate and identify all components and hardware. Step 3: Attach the center post to the FunCenter base. See Detail A. Insert the post up through the bottom of the base, align the holes, and attach as shown. Fully tighten the connections. Step 4: Insert the long center panel into the FunCenter base and push down to "snap" in place. See Detail B. Step 5: Insert the frame and tracing panels into the FunCenter base and push down to "snap" in place See Detail C. Final Details. Step 6: For areas complying with ASTM standard F1487 apply the age appropriate label to the component at eye level. Page 5 of 8

6 Bill of Materials PD INFANT FUN CENTER PART NO. DESCRIPTION QTY. ASY0044 ASSEMBLY - INFANT FUN CENTER FRAME PANEL 1 ASY0045 ASSEMBLY - INFANT FUN CENTER TRACING PANEL 1 ASY0046 ASSEMBLY - INFANT FUN CENTER 1 ASY0055 ASSEMBLY - INFANT FUN CENTER LONG PANEL 1 BAE0077 BOLT - 3/8"-16 x 1-1/2" KNOB 2 BPL0074 INFANT FUN CENTER - CENTER POST 1 ALB0038 LABEL - AGE APPROPRIATE SHEET 1 For Customer Service, Call or OUTSIDE U.S Buffalo Road Lewisburg, PA Playworld Systems, Inc. PlayDesigns is a brand of Playworld Systems, Inc. Page 6 of 8

7 Plastic Parts Inspect all plastic surfaces for sharp points, cracks or jagged edges. If any damage is detected and is determined to be unsafe, barricade equipment to prevent use until repair is completed. Minor burrs or sharp edges may be removed by using a sharp utility knife or block plane to remove sharp burr. Equipment Maintenance PlayDesigns Infant FunCenter Moving Parts Inspect moving parts to make sure they are securely attached to the panels and function properly. Fasteners Inspect for loose fasteners. Tightening torque specifications are: Bolts and Nuts: Snug tighten and tighten an additional one-half turn. Inspect for missing, worn or broken fasteners. If any missing, worn or broken fasteners are found, refer to the installation instructions for proper replacement fastener. If any damage is detected, barricade equipment to prevent use until repair is completed. Contact your sales representative immediately for a replacement part. Cleaning All plastic surfaces should be cleaned with a non-toxic, non-abrasive, antibacterial cleaning product. Mirrors should be cleaned with a non-toxic, non-abrasive glass cleaner. Replacement Parts Refer to your installation instructions to obtain replacement part number. Contact your sales representative or call Playworld Systems Customer Service for a replacement part. For Customer Service, Call or OUTSIDE U.S Buffalo Road Lewisburg, PA Playworld Systems, Inc. PlayDesigns is a brand of Playworld Systems, Inc. Page 7 of 8

8 Installation Inspection Form Instructions Be sure that you are using a copy of this Inspection Form and not your original. Use the Inspection Codes listed below and record condition of equipment at time of examination on the Inspection Checklist. Document any item from the Inspection Checklist that will require maintenance along with any corrective action on the Maintenance Schedule. Be sure to include appropriate dates and signatures on each section to properly document maintenance procedure. Preventive Maintenance... for Safety's Sake! INSPECTION CHECKLIST Inspect plastic parts for damage. Inspect for loose, missing, worn, or broken fasteners. Inspect moving parts for proper function. Frequency Medium High Medium Inspection Code Date Date Repairs Completed Inspection Codes P = Pass F = Fail NA = Not Applicable Inspect for clean and sanitary, non-obstructed surfaces. High Inspector: Name (Please Print) Signature: Date: / / MAINTENANCE SCHEDULE Item in Question Description of Problem Corrective Action Date Repairer: Name (Please Print) Page 8 of 8 Signature: Date: / /